NXP Austria CLEV6630B Customer Evaluation Board CLEV6630B User Manual Integration Manual EXPLORE NFC

Download:
Mirror Download [FCC.gov]
Document ID	3321721
Application ID	rpm21xvIwpaUpPzKlXZ7nA==
Document Description	Integration Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	105.04kB (1313044 bits)
Date Submitted	2017-03-17 00:00:00
Date Available	2017-03-17 00:00:00
Creation Date	2017-03-17 07:48:24
Producing Software	LibreOffice 5.0
Document Lastmod	0000-00-00 00:00:00
Document Title	Integration Manual EXPLORE-NFC
Document Creator	Writer
Document Author:	Pavel Slamnik

Integration Manual: Customer Evaluation
Board CLRC663, CLEV6630B
Doc Rev 1.00 Approved — 2017.02.15
1. Customer Evaluation Board CLRC663, CLEV6630B: Photo
Figure 1: Customer Evaluation Board CLRC663, CLEV6630B – side view.
Figure 2: Customer Evaluation Board CLRC663, CLEV6630B – bottom view.
BL ID
2. Customer Evaluation Board CLRC663, CLEV6630B: Description
1.
Operational desription
Customer Evaluation Board CLRC663, CLEV6630B, is an example of implementation of
ISO/IEC 14443A and ISO/IEC 14443B reader/writer and NFC reader/writer (P2P passive
initiator mode) on the same printed board. Middle size antenna, implemented on the same
pcb, permits reading/writing on distance up to 50 mm (RFID card or other NFC device). The
onboard USB connector permits direct connection and communication with personal
computer.
Power supply is via usb port or via SELV rated and limited power source ( 7-13.5V / 500mA).
On the Customer Evaluation Board CLRC663, CLEV6630B main parts are easily visible:
•
the pcb antenna,
•
the antenna matching components,
•
the reader part: CLRC663 reader IC, LPC 1769 microcontroller IC, two crystall
oscillators and decopling capacitors, power supply ICs and EEPROM, USB serial
communication port and JTAG port.
The Customer Evaluation Board CLRC663, CLEV6630B uses USB serial communiation port
for communicating with personal computer and transfer data. JTAG port is for development
purposes (programming). Some test pins are added on pcb.
The Customer Evaluation Board CLRC663, CLEV6630B has following features:
•
Supports ISO/IEC 14443A and ISO/IEC 14443B reader/writer up to 848 Kbps.
•
Supports MIFARE 1K/4K encryption in reader/writer mode.
•
Supports contactless RF communication according to the FeliCa protocol at 212 Kbps
and 424 Kbps.
•
Supports P2P passive initiator mode in accordance with ISO/IEC 18092
•
P2P supported for types: A (106 kbit/s), F (212, 424 kbit/s)
•
ISO/IEC15693 reader (I-Code)
•
ISO/IEC 18000 EPC-HF reader (I-Code ILT)
•
EMVCo 2.3.1 digital & analog Compliance
•
Serial communication via USB port with Personal computer
•
Power supply via USB port or via external power adapter.
Disclaimer:
This module is intended only for development and evaluation purposes, and cannot be used
in a finished product.
Figure 3: Customer Evaluation Board CLRC663, CLEV6630B - Block diagram.
Figure 4: Customer Evaluation Board CLRC663, CLEV6630B: dimensions, pcb with
elements.
3. Customer Evaluation Board CLRC663, CLEV6630B: SPECIFICATION
3.1.
Customer Evaluation Board CLRC663, CLEV6630B: Specifications
Table 2: Customer Evaluation Board CLRC663, CLEV6630B – specifications
Antenna
PCB type, 65 mm x 65 mm
Contactless operating frequency
13.56 MHz
Card reading/writing distance
Up to 50 mm
Contactless (RFID) Smart Card Interface
Reader/Writer mode
ISO 14443 A up to 848 Kbps transmission rate (depending on card)
ISO 14443 B up to 848 Kbps transmission rate (depending on card)
NXP Mifare Crypto 1 intellectual property
Reader/Writer mode supporting JIS X 6319-4 (comparable with FeliCa scheme)
ICODE EPC UID / EPC OTP
SO/IEC15693 reader
ISO/IEC 18000-3 mode 3 / EPC Class-1 HF reader (I-Code ILT)
EMV Contactless protocol specification V2.3.1 on RF level
Peer to Peer mode
Passive-Initiator / Passive-Target acc. ISO/IEC 18092
P2P supported for types: A (106 kbit/s), F (212,424 kbit/s)
Microcontroller LPC1769
ARM Cortex-M3 based microcontroller with 512 kb internal flash memory, 64 kb
internal RAM
Clock Crystals
12.000 MHz crystal for CPU
Firmware
Customer developed firmware for testing PN5180 functionality
Host Interface
Host Interface
USB 2.0 (also supported USB 1.1)
Transmission Speed
12 Mbps (USB 2.0 full speed)
Power Supply
Bus powered
Other Communication
Interfaces
JTAG IEEE1149.1 Serial
Interface
JTAG 10-pin connector; to connect JTAG adapter
Electrical and Mechanical Specifications
Power Supply
5V DC 5%, 500 mA (via USB port) or
external power suply 7 – 13.5 V DC / 500 mA
PCB Dimensions (L x W x H)
152 mm x 68 mm x 15 mm
Weight
approx. 40 g
Operating Temperature
0… + 40 C (without condensing)
Storage temperature
-40 … + 85 C (without condensing)
Operating Humidity
5 … 95% RH
Certificates
CE, FCC
3.2.
Customer Evaluation Board CLRC663, CLEV6630B: Electrical characteristics
Table 3: Customer Evaluation Board CLRC663, CLEV6630B – Electical Specifications
Operating Range
Symbol
Description
Conditions
Min
Typ
Max
Unit
7-13.5V
DC
DC Power Supply
Active Reader
7.0
13.5
VUSB
DC Power Supply
Active Reader
4.75
5.0
5.25
Tamb
Ambient Temperature
+25
+40
C
Min
Typ
Max
Unit
350
450
mA
Min
Typ
Max
Unit
0 – 50
mm
Current Consumption
Symbol
Description
Conditions
IC5V
Supply Current
Active, RF on
Operating Distance
Symbol
Description
Conditions
DST
Operating Distance
Measured from the center of
the antenna
USB Interface Characteristics
Symbol
Description
Conditions
USB
Baudrate
micro B USB Connector
Min
Typ
Max
12
Unit
Mbaud
4. INSTALLING MANUAL
4.1.
Desktop use
Customer Evaluation Board CLRC663, CLEV6630B is intended for development use in
development environment such are development departements in factories, at institutes.
CLEV6630B board is powered via USB serial connection from personal computer or via
external power supply.
Usuall climate conditions in development environment (room temperature and humidity) are
deep inside Customer Evaluation Board CLRC663, CLEV6630B specified climate conditions.
4.2.
Power supply
Customer Evaluation Board CLRC663, CLEV6630B has no power supply mounted on pcb.
There are two possibilties to connect external power supply:
- powering via USB port (micro B usb connector) from personal computer or
- via external power supply 7-13.5V DC / 500mA.
Which option is used is set with jumper J101 (figure 4).
The micro B USB connector is used for connection to the PC usb port – for power supply
and USB serial communication. Used this power option is default setting with jumper J101.
USB A male to micro B USB (5 pin) cable is used for connection between Customer
Evaluation Board CLRC663, CLEV6630B and personal computer.
External power supply 7-13.5V / 500mA is connected to power jack J100 to supply Customer
Evaluation Board CLRC663, CLEV6630B. On board IC LT1129IST-5 is used to stabilize
voltage to 5V.
Note 1:
Power supply from USB port on personal computer has to comply with LPS requirement of
IEC60950-1.
Maximum lenght for USB cable is 1.8 meter.
Note 2:
External power supply 7 – 13.5V / 500mA has to comply with LPS requirement of IEC609501.
Maximum lenght for power cable is 1.8 meter.
5. USER MANUAL
Customer Evaluation Board CLRC663, CLEV6630B is an example of implementation of
ISO/IEC 14443A and ISO/IEC 14443B reader/writer, NFC reader/writer and Card Emulation
Device on the same printed board. Middle size antenna, implemented on the same pcb,
permits reading/writing on distance up to 50 mm (RFID card or other NFC device). The
onboard USB connector permits direct connection and communication with personal
computer.
Customer Evaluation Board CLRC663, CLEV6630B is inteded to send and receive data
according to the ISO 14443A and ISO 14443B protocol. Data transfer from reader to/from
contactless cards operates at frequency 13.56 MHz. Data transfer between CLRC663 reader
IC and microcontroller LPC1769 is via SPI serial communication.
The firmware for testing and development purposes is written into LPC1769 microcontroller.
But user can develop his own firmware and write it via JTAG port into LPC1769 memory.
Power supply is via usb port or via external power supply ( 7-13.5V / 500mA).
How to installing user developed firmware is written in detail in Quick Start Guide (and ARM
Board User Manual).
5.1.
General user instructions
Reading/writing is possible with MIFARE contactless cards, FeliCa cards or with NFC
device.
CLEV6630B board can detect contactless card or NFC device up to 50 mm from the
center reader's antenna.
CLEV6630B board can emulate contactless (NFC) card.
Contactless card identification is possible in electromagnetic field (created from
contactless reader). Nonmetal material between antenna and RFID contactless card
have no influence to reading distance or reading reliability.
Reading/writing to/from card is very simple: user approaches his contactless card to
reader's antena. CLEV6630B board detects card and confirm reading via serial (USB)
communication to personal computer (depend from customer firmware). Successfully
reading/writing can be signalised with status led diode on CLEV6630B board.
5.2.
Instructions for safe work, maintaining and care
•
Be careful not to damage the connectors, antenna, PCB, ICs and other connected
parts.
•
Because of the specifics of the device and the damage, only quallified staff, authorized
by the producer, are allowed to repair the device. All interventions of the unauthorized
person and mechanical damage means repealing of the guarantee.
6. ELECTROMAGNETIC COMPATIBILITY
Customer Evaluation Board CLRC663, CLEV6630B fulfils the following requirements of
electromagnetic compatibility:
FCC, Part 15 and CE.
6.1 FCC Compliance Statement
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Compliance for Limited Modular Approval (§15.212(b))
As note, the module is intended for PROFESSIONAL AND DEVELOPMENT USE ONLY and
cannot be used in final products. The module is tested to comply with relevant part 15 rules
without shielding and in the same configuration as it is intended to be used by developer.
CLEV6630B board has passed spurious emissions test without shielding and is certified as
limited modular transmitter. Under FCC part 15.212(b), shielding is not required.
Concerning §2.803 the CLEV6630B board will be not offered for sale to other parties or to
end users located in a residential environment.
Caution!
The Federal Communications Commission warns the users that changes or modifications to
the unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
6.2 COMPLIANCE INFORMATION according to 47CFR 2.1033
We, declare that the product
Customer Evaluation Board CLRC663, CLEV6630B
FCC 12.225, Limited Modular Approval, FCC ID: OWRCLEV6630B
is in conformity with Part 15 of the FCC Rules.
Operation of this product is subject to the following conditions:
(1) this device may not cause harmful interference
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 12
Language                        : sl-SI
Title                           : Integration Manual EXPLORE-NFC
Author                          : Pavel Slamnik
Subject                         : Integration Manual
Keywords                        : Integration, Manual
Creator                         : Writer
Producer                        : LibreOffice 5.0
Create Date                     : 2017:03:17 07:48:24+01:00

EXIF Metadata provided by EXIF.tools