NXP Austria OM25180TWR 13.56 MHz RFID Module User Manual AN11806

Download:
Mirror Download [FCC.gov]
Document ID	3052982
Application ID	Ff3AFvrWIWzqX/0tdr+juw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	234.41kB (2930186 bits)
Date Submitted	2016-07-06 00:00:00
Date Available	2016-07-06 00:00:00
Creation Date	2016-05-25 13:55:36
Producing Software	Microsoft® Word 2013
Document Lastmod	2016-05-25 13:55:36
Document Title	AN11806
Document Creator	Microsoft® Word 2013
Document Author:	Christophe lombardo

AN11806
TWR-POSCARD Hardware description
Rev. 1.1 — 25 May 2016
366410
Application note
COMPANY CONFIDENTIAL
Document information
Info
Content
Keywords
TWR_POSCARD, SPI, E.M.V, Kinetis, PN5180, TDA8035
Abstract
This application note describe the TWR_POSCARD evaluation board to
be used with NXP’s Kinetis K80 family chip.
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Revision history
Rev
Date
Description
1.0
20160303
Initial revision
1.1
20160525
Add FCC Warning Statement
Contact information
For more information, please visit: http://www.nxp.com
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
2 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
1. Presentation
TWR-POSCARD is a peripheral module board to be used with NXP’s Tower system.
Fig 1.
Tower System
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
3 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
1.1 Daughter board
TWR-POSCARD is a peripheral board that can be plugged into a tower system to add
Contact and Contactless EMV reader functionality.
TWR-POSCARD is the below board:
Fig 2.
TWR-POSCARD V2 Top view
This board can be plugged as in Fig 1, using the TWR-ELEV boards (side connector
boards).
When plugging this board, the Primary and Secondary connection sides have to be
respected. PCI secondary and primary connector are identified on TWR-POSCARD, and
on TWR-ELEV card, see below figure.
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
4 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 3.
TWR-Elev: Secondary and Primary
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
5 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
1.2 Architecture
The TWR-POSCARD peripheral board embeds ICs to provide Contact and Contactless
payment functionalities.
The board uses the following ICs:
PN5180: NXP Contactless Front-end reader
TDA8035: NXP Contact Front-end reader device.
Both devices are compliant with latest payment specifications (EMVCo)
The reader ICs are controlled by an MCU or processor module, through the side
connectors, plugged on Tower system.
In order to interface with smart cards, the TWR-POSCARD board is autonomous as it
embeds an antenna connected to PN5180 to interact with Contactless cards, and a
contact smart card connector, connecting the smart card to the TDA8035.
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
6 of 23
AN11806
NXP Semiconductors
Smart Card
Connector
Antenna
TDA8035
PN5180
TWR-POSCARD
TWR-ELEV
TWR-ELEV
TWR-POSCARD Hardware description
MCU
Fig 4.
AN11806
Application note
COMPANY CONFIDENTIAL
Architecture view
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
7 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
1.3 Configuration
The TWR-POSCARD peripheral board embeds several configuration jumpers. They are
used to enable several Tower MCU or processor modules to be used as the controller.
Below table shows the default configuration when the TWR-K80F150M is used as the
MCU module. Other configurations can be set depending on the MCU or processor
module board that is used.
Table 1.
Jumper
Name
J1
J2
Configuration jumpers for K81
Function
Options
PN5180 SPI NSS
PN5180 SPI MISO
J3
PN5180 SPI MOSI
J4
PN5180 SPI SCL
J5
J6
J7
Connection
(default in bold)
PN5180 IRQ
TDA8035 Presence N
TDA8035 Clock input
SPI1_CS0 - Pin B9 on Elevator
1-2
SPI0_CS0 - Pin B46 on Elevator
2-3
SPI1_MISO - Pin B11 on Elevator
1-2
SPI0_MISO - Pin B44 on Elevator
2-3
SPI1_MOSI - Pin B10 on Elevator
1-2
SPI0_MOSI - Pin B45 on Elevator
2-3
SPI1_CLK - Pin B7 on Elevator
1-2
SPI0_CLK - Pin B48 on Elevator
2-3
IRQ_A - Pin B62 on Elevator
1-2
IRQ_F - Pin B57 on Elevator
2-3
PWM3 - Pin A37 on Elevator
1-3
GPIO14 - Pin A50 on Elevator
3-5
ULPI_DATA1 - Pin C22 on Elevator
4-6
PWM1 - Pin A39 on Elevator
1-3
PWM0 - Pin A40 on Elevator
3-5
I2S1_DIN_SCK - Pin C58 on Elevator 4-6
J8
J9
J10
TDA8035 IOUC
1-3
PWM2 - Pin A38 on Elevator
3-5
I2S1_DIN_WS - Pin C59 on Elevator
4-6
ETH_RXDV_1 - Pin A16 on Elevator
1-2
I2S0_DOUT_SCK - Pin A22 on Elev.
2-3
UART0_TX - Pin A42 on Elevator
1-2
UART1_TX - Pin A44 on Elevator
2.3
TDA8035 IOUC
I2S1_DOUT1 - Pin C61 on Elevator
1-2
J12 1-3-5
TDA8035 CMDVCCN
ULPI_DATA4 - Pin C25 on Elevator
1-3
GPIO1 - Pin B21 on Elevator
3-5
IRQ_C - Pin B60 on Elevator
2-4
IRQ_B - Pin B61 on Elevator
4-6
PWM3 - Pin A37 on Elevator
1-2
J16 1-2
Application note
COMPANY CONFIDENTIAL
TDA8035 IOUC
GPIO17 - Pin A53 on Elevator
J11
J12 2-4-6
AN11806
TDA8035 RSTIN
TDA8035 OFFN
Connect
MCU_ICC_PDA37
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
8 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
AN11806
Application note
COMPANY CONFIDENTIAL
Jumper
Name
Function
Options
Connection
J16 3-4
Connect
MCU_ICC_RST_A38
PWM2 - Pin A38 on Elevator
3-4
J19
PN5180 BUSY
IRQ_D - Pin B59 on Elevator
1-2
IRQ_E - Pin B58 on Elevator
2-3
J20
PN5180 RESET
SPI1_CS1 - Pin B58 on Elevator
1-2
J21 1-2
Connect
MCU_MSR_DATA
TMR1 - Pin A33 on Elevator
1-2
J21 3-4
Connect
MCU_MSR_STROBE
TMR0 - Pin A34 on Elevator
1-2
J22
Connect
GPIO3 - Pin B23 on Elevator
MCU_ICC_CVVV_SEL0
1-2
J23
Connect
GPIO9 - Pin A9 on Elevator
MCU_ICC_CVVV_SEL1
1-2
(default in bold)
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
9 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
2. Design files
2.1 Schematics
Fig 5.
Contactless Front-end
Fig 6.
PN5180 Configuration
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
10 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 7.
TDA8035
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
11 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 8.
Contact Jumper settings
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
12 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 9.
Tower Connector - Primary
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
13 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 10. Tower Connector - Secondary
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
14 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 11. Other
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
15 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
2.2 Layout and placement
Fig 12. Board placement
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
16 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 13. Layout TOP
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
17 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 14. Layer in #1
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
18 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 15. Layer in #2
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
19 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
Fig 16. Layout Bottom
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
20 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
3. FCC Part 15 Warning Statements
3.1 FCC Part 15.19 Warning Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
3.2 FCC Part 15.21 Warning Statement
The user manual for an intentional or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.
3.3 FCC Part 15.105(b) Warning Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
AN11806
Application note
COMPANY CONFIDENTIAL
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 2016. All rights reserved.
21 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
4. Legal information
4.1 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences
of use of such information.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
4.2 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation lost profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability
towards customer for the products described herein shall be limited in
accordance with the Terms and conditions of commercial sale of NXP
Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP
Semiconductors accepts no liability for any assistance with applications or
customer product design. It is customer’s sole responsibility to determine
whether the NXP Semiconductors product is suitable and fit for the
customer’s applications and products planned, as well as for the planned
application and use of customer’s third party customer(s). Customers should
provide appropriate design and operating safeguards to minimize the risks
associated with their applications and products.
AN11806
Application note
COMPANY CONFIDENTIAL
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
Evaluation products — This product is provided on an “as is” and “with all
faults” basis for evaluation purposes only. NXP Semiconductors, its affiliates
and their suppliers expressly disclaim all warranties, whether express,
implied or statutory, including but not limited to the implied warranties of noninfringement, merchantability and fitness for a particular purpose. The entire
risk as to the quality, or arising out of the use or performance, of this product
remains with customer.
In no event shall NXP Semiconductors, its affiliates or their suppliers be
liable to customer for any special, indirect, consequential, punitive or
incidental damages (including without limitation damages for loss of
business, business interruption, loss of use, loss of data or information, and
the like) arising out the use of or inability to use the product, whether or not
based on tort (including negligence), strict liability, breach of contract, breach
of warranty or any other theory, even if advised of the possibility of such
damages.
Notwithstanding any damages that customer might incur for any reason
whatsoever (including without limitation, all damages referenced above and
all direct or general damages), the entire liability of NXP Semiconductors, its
affiliates and their suppliers and customer’s exclusive remedy for all of the
foregoing shall be limited to actual damages incurred by customer based on
reasonable reliance up to the greater of the amount actually paid by
customer for the product or five dollars (US$5.00). The foregoing limitations,
exclusions and disclaimers shall apply to the maximum extent permitted by
applicable law, even if any remedy fails of its essential purpose.
4.3 Licenses
Purchase of NXP ICs with NFC technology
Purchase of an NXP Semiconductors IC that complies with one of the Near
Field Communication (NFC) standards ISO/IEC 18092 and ISO/IEC 21481
does not convey an implied license under any patent right infringed by
implementation of any of those standards. Purchase of NXP
Semiconductors IC does not include a license to any NXP patent (or other
IP right) covering combinations of those products with other products,
whether hardware or software.
4.4 Trademarks
Notice: All referenced brands, product names, service names and
trademarks are property of their respective owners.
MIFARE — is a trademark of NXP Semiconductors N.V.
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 25 May 2016
366410
© NXP Semiconductors N.V. 20164. All rights reserved.
22 of 23
AN11806
NXP Semiconductors
TWR-POSCARD Hardware description
5. Contents
1.
1.1
1.2
1.3
2.
2.1
2.2
3.
3.1
3.2
3.3
4.
4.1
4.2
4.3
4.4
5.
Presentation......................................................... 3
Daughter board .................................................. 4
Architecture ........................................................ 6
Configuration ...................................................... 8
Design files ........................................................ 10
Schematics....................................................... 10
Layout and placement ...................................... 16
FCC Part 15 Warning Statements .................... 21
FCC Part 15.19 Warning Statement ................. 21
FCC Part 15.21 Warning Statement ................. 21
FCC Part 15.105(b) Warning Statement .......... 21
Legal information .............................................. 22
Definitions ........................................................ 22
Disclaimers....................................................... 22
Licenses ........................................................... 22
Trademarks ...................................................... 22
Contents ............................................................. 23
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in the section 'Legal information'.
© NXP Semiconductors N.V. 2016.
All rights reserved.
For more information, visit: http://www.nxp.com
Date of release: 25 May 2016
366410
Document identifier: AN11806

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 23
Language                        : fr-FR
Tagged PDF                      : Yes
Title                           : AN11806
Author                          : Christophe lombardo
Creator                         : Microsoft® Word 2013
Create Date                     : 2016:05:25 13:55:36+02:00
Modify Date                     : 2016:05:25 13:55:36+02:00
Producer                        : Microsoft® Word 2013

EXIF Metadata provided by EXIF.tools