NXP Semiconductors JN5169U0V2 ZigBee Modular Transmitter User Manual UM11030
NXP Semiconductors ZigBee Modular Transmitter UM11030
Contents
- 1. User manual
- 2. User manual rev.pdf
User manual rev.pdf
UM11030 JN5169-001-U00-2 USB Dongle User Manual Rev. 1.1 — 28 February 2017 Document information Info Content Keywords JN5169, ZigBee, dongle, USB Abstract JN5169-001-U00-2 USB dongle user manual User manual UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual Revision history Rev Date Description 1.0 20160928 First release 1.1 20170228 SAR condition Correction Contact information For more information, please visit: http://www.nxp.com UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 2 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 1. Introduction This chapter introduces the NXP JN5169-001-U00-2 USB Dongle (DR1198), which provides a hardware development platform for wireless microcontroller applications with a USB interface. 1.1 Overview The JN5169-001-U00-2 USB Dongle features a JN5169 wireless microcontroller and allows communication with this JN5169 device from a USB connection. The JN5169 device can act as a node of a wireless network. Thus, the dongle provides an easy way of interfacing a host machine (such as a PC) to a wireless network based on the IEEE802.15.4, ZigBee Smart Energy or ZigBee-Home Automation networking protocol. An FTDI device provides the USB connection between the host machine and the JN5169 device, which in turn provides the radio interface to the wireless network. Typical uses of the dongle include: A complete and stable hardware environment for the development of IEEE802.15.4, ZigBee Smart Energy and ZigBee-Home Automation networking applications, facilitating an accelerated time-to-market for wireless network products The basis of a packet sniffer for IEEE 802.15.4-based wireless communications A means of integrating the host machine into a wireless network, typically as the network Coordinator The small-footprint PCB of the dongle provides all the necessary components for a wireless microcontroller with access to a USB connection. All RF layout and decoupling issues are handled by the design of this dongle. Therefore, this design is ready for application development without the necessity of hardware development. The JN5169 USB dongle, shown Fig 1, is supplied in the JN5169-EK004 Evaluation Kit. Fig 1. UM11030 User manual JN5169-001-U00-2 USB dongle (DR1198) All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 3 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 1.2 Features The dongle has the following features: USB 2.0 Full-Speed Compatible Interface IEEE 802.15.4-based wireless microcontroller (JN5169) with the following radio characteristics: o Transmit power: 8.5 dBm (typ.), can be increased to 10 dBm (typ.) o Transmit current: 19.6 mA (typ) at 8.5 dBm / 23.3 mA (typ.) at 10 dBm o Receive sensitivity: 96dBm (typ.) o Receive current: 13 mA (typ.) Integrated printed RF antenna General-purpose LEDs (one green, one orange) Serial Flash memory device (4 Mbits) 32-kHz crystal oscillator 2. Hardware overview 2.1 Dongle layout Fig 2. UM11030 User manual DR1198 board layout All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 4 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 2.2 Dongle block diagram The Fig 3 illustrates the main hardware blocks of the dongle. Fig 3. JN5169-001-U00-2 USB dongle hardware blocks 2.3 Hardware components The hardware components on the board are described in the following sub-sections. JN5169 wireless microcontroller – see section 2.3.1 FTDI FT232RL driver device – see section 2.3.2 LEDs – see section 2.3.3 32-kHz crystal oscillator – see section 2.3.4 2.3.1 JN5169 device The JN5169 circuit on the board is based around the standard JN5169-001-M00 module. However, it is built on a 2-layer board, as the DIOs do not need to be externally available. The JN5169 device uses an integrated antenna on the PCB of the dongle. UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 5 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 2.3.2 FT232RL device The FT232RL device is connected to the USB connector and acts as an interface between the PC and the JN5169 device. The FT232RL will enumerate on the PC as a virtual COM port connected directly to UART0 on the JN5169 device. The IO controls C2 and C3 in the FT232RL device need to be set to ’I/O Mode’ to allow the RESET and PGM signals to operate correctly. To do this, execute the following instructions. 1. Download the application FT_Prog from the FTDI website www.ftdichip.com 2. Insert the JN5169 USB Dongle into a USB port of your computer and wait for the device to enumerate 3. Start FT_Prog and click Scan and Parse (the magnifying glass button) 4. Update the IO controls C2 and C3 to I/O MODE – see Fig 4 UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 6 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual Fig 4. IO controls window 5. Click Program Devices (the lightning button) 6. On the resulting screen, click Program – see Fig 5 UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 7 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual Fig 5. Program devices window 2.3.3 LEDs There are two surface-mounted LEDs that can be controlled by the JN5169 wireless microcontroller (see Fig 2 for locations): LED D1 (green) LED D2 (orange) Both LEDs are connected to DIO16 and DIO17. These DIOs can be used to control the LEDs as indicated in the Table 1. Table 1. DIO control of LEDs DIO17 DIO16 Low High Low High D1: Off D1: Off D2: Off D2: On D1: On D1: Off D2: Off D2: Off 2.3.4 32-kHz crystal oscillator The JN5169 device has an internal 32-kHz RC oscillator. In order to provide more accurate system timings, an external 32-kHz crystal can be used with the device. This is provided on the JN5169-001-U00-2 USB dongle and can be enabled from the JN5169 application using the JN5169 Integrated Peripherals API - refer to the JN5169 Integrated Peripherals API User Guide (JN-UG-3087). UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 8 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 3. Flash programming When the JN5169-001-U00-2 USB dongle is powered up, it attempts to run an application from the internal Flash memory of the JN5169 device. This may be a selfcontained application that sends and receives wireless data, and which does not need to communicate with the host. Alternatively, it may communicate via the USB with an application running on the host, such as a Windows program, and also communicate with a wireless device or network. In order to program an application binary into Flash memory, the JN51xx Production Flash Programmer can be used, which is described in the JN51xx Production Flash Programmer User Guide (JN-UG-3099). This programming utility will place the JN5169 into its programming mode. It will then download the program to the Flash memory and reset the JN5169 device, causing the application to be executed. 4. Compliance statements and documentation The FCC ID number of the JN5169-001-U00-2 USB dongle is XXMJN5169U0V2 The IC ID number of the JN5169-001-U00-2 USB dongle is 8764A-JN5169U0V2 4.1 FCC statements and documentation This section contains the Federal Communication Commission (FCC) statements and documents. 4.1.1 FCC interference statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 9 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual FCC caution: User guide mandatory statements User's instructions of the host device must contain the following statements in addition to operation instructions: * “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation” * “Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment” WARNING! FCC radiation exposure statement: This device complies with FCC radiation exposure limits set forth for general population (uncontrolled exposure). This device must not be collocated or operating in conjunction with any other antenna or transmitter. RF exposure guidelines require that the device be used at a minimum of 0.5cm from the human body. Failure to observe this guideline may result in RF exposure exceeding limits. Certification information (SAR): This device is also designed to meet the requirements for exposure to radio waves established by the FCC (USA). The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported to the FCC for this device complies with this limit. UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 10 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 4.2 Industry Canada statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. RF exposure requirements: This device complies with FCC radiation exposure limits set forth for general population (uncontrolled exposure). This device must not be collocated or operating in conjunction with any other antenna or transmitter. RF exposure guidelines require that the device be used at a minimum of 0.5 cm from the human body. Failure to observe this guideline may result in RF exposure exceeding limits. Certification information (SAR): This device is also designed to meet the requirements for exposure to radio waves established by the Industry Canada. The SAR limit adopted by Canada is 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported to IC for this device complies with this limit. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt a accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Exigences RF en matière d’exposition : Cet appareil est conforme aux limites d’exposition RF générales des personnes. Cet appareil ne doit pas être co-localisé ou utilisé en conjonction avec d’autres émetteurs. Les directives d'exposition RF exigent que l’appareil soit utilisé à une distance minimum de 0.5 cm du corps humain. Le non-respect de cette directive peut entraîner une exposition RF dépassant les limites. Informations de Certification (DAS): Cet appareil est également conçu pour répondre aux exigences d'exposition aux ondes radio établies par l'Industrie Canada. La limite DAS adoptée par le Canada est de 1,6 W/kg sur 1 gramme de tissu. La valeur DAS la plus élevée signalée à l'IC pour ce type d'appareil est conforme à cette limite. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropic radiated power (e.i.r.p.) is not more than that permitted for successful communication UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 11 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 5. Abbreviations Table 2. Abbreviations Acronym Description BOM Bill Of Materials DIO Digital Input/Output FCC Federal Communication Commission IC Industry Canada PCB Printed Circuit Board UART Universal Asynchronous Receiver/Transmitter USB Universal Serial Bus 6. References UM11030 User manual [1] JN5169 JN5169 Data Sheet [2] JN-UG-3087 JN516x Integrated Peripherals API User Guide [3] DR1198_JN5169_USB_Dongle_1V0b DR1198 USB dongle PCB files All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 12 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 7. Legal information 7.1 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. 7.2 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or UM11030 User manual customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Evaluation products — This product is provided on an “as is” and “with all faults” basis for evaluation purposes only. NXP Semiconductors, its affiliates and their suppliers expressly disclaim all warranties, whether express, implied or statutory, including but not limited to the implied warranties of noninfringement, merchantability and fitness for a particular purpose. The entire risk as to the quality, or arising out of the use or performance, of this product remains with customer. In no event shall NXP Semiconductors, its affiliates or their suppliers be liable to customer for any special, indirect, consequential, punitive or incidental damages (including without limitation damages for loss of business, business interruption, loss of use, loss of data or information, and the like) arising out the use of or inability to use the product, whether or not based on tort (including negligence), strict liability, breach of contract, breach of warranty or any other theory, even if advised of the possibility of such damages. Notwithstanding any damages that customer might incur for any reason whatsoever (including without limitation, all damages referenced above and all direct or general damages), the entire liability of NXP Semiconductors, its affiliates and their suppliers and customer’s exclusive remedy for all of the foregoing shall be limited to actual damages incurred by customer based on reasonable reliance up to the greater of the amount actually paid by customer for the product or five dollars (US$5.00). The foregoing limitations, exclusions and disclaimers shall apply to the maximum extent permitted by applicable law, even if any remedy fails of its essential purpose. 7.3 Trademarks Notice: All referenced brands, product names, service names and trademarks are property of their respective owners. All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 13 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 8. List of figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. JN5169-001-U00-2 USB dongle (DR1198) ....... 3 DR1198 board layout ........................................ 4 JN5169-001-U00-2 USB dongle hardware blocks ................................................................ 5 IO controls window ............................................ 7 Program devices window .................................. 8 UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 14 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 9. List of tables Table 1. Table 2. DIO control of LEDs .......................................... 8 Abbreviations .................................................. 12 UM11030 User manual All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 28 February 2017 © NXP Semiconductors N.V. 2014. All rights reserved. 15 of 16 UM11030 NXP Semiconductors JN5169-001-U00-2 USB Dongle User Manual 10. Contents 1. 1.1 1.2 2. 2.1 2.2 2.3 2.3.1 2.3.2 2.3.3 2.3.4 3. 4. 4.1 4.1.1 4.2 5. 6. 7. 7.1 7.2 7.3 8. 9. 10. Introduction ......................................................... 3 Overview ............................................................ 3 Features ............................................................. 4 Hardware overview .............................................. 4 Dongle layout ..................................................... 4 Dongle block diagram ........................................ 5 Hardware components ....................................... 5 JN5169 device ................................................... 5 FT232RL device ................................................. 6 LEDs .................................................................. 8 32-kHz crystal oscillator ..................................... 8 Flash programming ............................................. 9 Compliance statements and documentation .... 9 FCC statements and documentation .................. 9 FCC interference statement ............................... 9 Industry Canada statement .............................. 11 Abbreviations .................................................... 12 References ......................................................... 12 Legal information .............................................. 13 Definitions ........................................................ 13 Disclaimers....................................................... 13 Trademarks ...................................................... 13 List of figures..................................................... 14 List of tables ...................................................... 15 Contents ............................................................. 16 Please be aware that important notices concerning this document and the product(s) described herein, have been included in the section 'Legal information'. © NXP Semiconductors N.V. 2014. All rights reserved. For more information, please visit: http://www.nxp.com Date of release: 28 February 2017 Document identifier: UM11030
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 16 Language : fr-FR Tagged PDF : Yes Title : UM11030 Author : Christophe Menard Creator : Microsoft® Word 2013 Create Date : 2017:02:28 14:01:37+01:00 Modify Date : 2017:02:28 14:01:37+01:00 Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools