Navico Auckland VHF7100US VHF MARINE RADIO User Manual USERS MANUAL

Navico Auckland Limited VHF MARINE RADIO USERS MANUAL

Contents

USERS MANUAL

1NAVMAN VHF 7000 / VHF 7100 Owner’s Manual
2IMPORTANT: 1. Some features described in this manual are not available on every model. In particular, DSC functions are NOT available on the NAVMAN VHF 7000.2. The radio channels installed into the NAVMAN VHF radio may vary from country to country, depending upon the NAVMAN VHF radio model and government or national communications authority regulations.3. NAVMAN NZ Ltd recommends that you check the radio operating licensing requirements of your country before using the NAVMAN VHF radio. The operator is solely responsible for observing proper radio installation and usage practices.4. A warning label is supplied with this NAVMAN VHF radio. To comply with FCC regulations, this label must be affixed in a location that is clearly visible from the operating controls of this NAVMAN VHF radio. Make sure that the chosen location is clean and dry before applying this label.It is the owner’s sole responsibility to install and use the instrument in such a manner that will not cause accidents, personal injury or property damage. NAVMAN NZ LIMITED disclaims all liability for any use of this product in a way that may cause acidents, damage or that may violate the law.Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of Documentation, the English language version of the Documentation will be the official version of the Documentation.This manual represents the NAVMAN VHF 7000 and NAVMAN VHF 7100 at the time of printing. NAVMAN NZ LIMITED reserves the right to make changes to specifications without notice.Copyright © NAVMAN NZ Limited, New Zealand. All rights reserved. NAVMAN is a registered trademark of NAVMAN NZ Limited.FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:•reorient or relocate the receiving antenna.•increase the separation between the equipment and receiver.•connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•consult the dealer or an experienced radio/TV technician for help.
3ContentsChapter 1 - General Information 51.1 FEATURES 51.2 CUSTOMIZING YOUR NAVMAN VHF RADIO 51.3 HOW TO DISPLAY AND NAVIGATE MENUS 61.4 HOW TO ENTER ALPHANUMERIC DATA 61.5 LCD SYMBOLS AND MEANINGS 61.6 BASIC OPERATION AND KEY FUNCTIONS 82.1 RADIO MENU OPTIONS (MENU) 11Chapter 2 - The Radio Menu (MENU) 112.2 MAINTAIN YOUR BUDDY LIST (BUDDY LIST) 122.2.1 Add an Entry 122.2.2 Edit an Entry 122.2.3 Delete an Entry 132.3 LOCAL OR DISTANCE SENSITIVITY (LOCAL/DST) 132.3.1 Set Distance Sensitivity 132.3.2 Set Local Sensitivity 132.4 BACKLIGHTING (BACKLIGHT) AND CONTRAST (CONTRAST) 142.4.1 Set the Backlighting Level 142.4.2 Set the Contrast Level 142.5 GPS DATA AND TIME (GPS/DATA) 142.5.1 MANUALLY ENTER Position & UTC TIME (MANUAL) 142.5.2 LOCAL Time DISPLAY (TIME OFFSET) 152.5.4 TIME DISPLAY OPTIONS (TIME DISPLAY) 162.5.6 Course & speed display options (COG/SOG) 162.5.7 GPS Alarm OPTIONS (ALARM) 172.6 GPS SIMULATOR (SIMULATOR) 172.7 RESET TO FACTORY DEFAULTS (RESET) 18Chapter 3 - Radio Setup Menu (RADIO SETUP) 193.1 RADIO SETUP MENU (RADIO SETUP) 193.2 CUSTOMIZE OR DELETE CHANNEL NAMES (CH NAME) 193.3 RING & BEEP VOLUME (RING VOLUME) & (BEEP VOLUME) 203.4 INTERNAL SPEAKER CONNECTIONS (INTERNAL SPK) 203.5 SET THE PRIORITY CHANNEL (WATCH MODE) 213.6 WEATHER ALERT (WX ALERT) 213.7 NMEA PROTOCOL (COMM PORT) 22Chapter 4 - DSC Setup Menu (DSC SETUP) 234.1 DSC SETUP - MENU OPTIONS 23
44.3 MAINTAIN YOUR GROUPS (GROUP SETUP) 244.3.1 Create a Group (GROUP SETUP) 244.3.2 EDIT GROUP NAME DETAILS (EDIT) 244.3.3 Delete a Group 254.4 RESPONSE TO INDIVIDUAL CALLS (INDIV REPLY) 254.5 ATIS MMSID AND ATIS FUNCTIONALITY (ATIS FUNC) 254.5.1 Enter or Edit the ATIS MMSID 254.5.2 Enable ATIS Functionality (ATIS FUNC) 264.7 RESPONSE TYPE TO LL CALLS (LL REPLY) 26Chapter 5 - Sending and Receiving DSC Calls 275.1 WHAT IS DSC? 275.2 SENDING DSC CALLS 275.2.1 Make a Routine Call MANUALLY (INDIV REPLY) 285.2.2 Retrying a Routine Call 285.2.3 ACKNOWLEDGE AN INDIVIDUAL CALL (INDIV ACK) 295.2.4 Recall the Most Recent INCOMING Call (LAST) 295.2.5 Call a Group (GROUP) 295.2.6 Call All Ships (ALL SHIPS) 305.2.7 CALL Using the Call Log (CALL LOG) 305.2.8 CALL using the distress log (DISTRES LOG) 315.3 RECEIVING DSC CALLS 325.3.1 Receiving an All ships call (ALL SHIPS) 325.3.2 receiving an individual call (INDIVIDUAL) 325.3.3 receiving A Group call (GROUP CALL) 33Chapter 6 - Distress Calls 346.1 SENDING A DISTRESS CALL 346.2 RECEIVING A DISTRESS CALL (DISTRESS!) 356.3 DISTRESS ACKNOWLEDGEMENT OR RELAY (DISTRESS ACK) 35Appendix A - Technical Specifications 36Appendix B - Troubleshooting 39Appendix C - VHF Marine Channel Charts 40C.1 INTERNATIONAL CHANNEL CHART 40C.2 USA CHANNEL CHART 43C.3 CANADA CHANNEL CHART 46C.4 EC CHANNEL CHART 49Appendix D - MMSID & License Information 52
5Chapter 1 - General Information1.1 FEATURESCongratulations on your purchase of a NAVMAN VHF 7000, 7100 USA, or 7100 EC marine band VHF radio. All of these models provide the following useful features:•prominent channel display •adjustable contrast settings for the LCD•adjustable keypad backlighting for easy night-time use•waterproof and submersible to comply with JIS-7•GPS latitude and longitude display (when connected to a GPS)•choice of High or Low (25 W or 1W) transmission power•top centred PTT button for comfortable left- or right-handed use•powerful 4W external audio output•access to all currently-available marine VHF channel banks (USA, Canada, International) including weather channels where available•special CH16 or CH16/9 key for quick access to the priority (international distress) channel•special 3CH key to select your three favourite channels•PSCAN (similar to dual watch) facilityIn addition, the VHF 7100 models also provide:•DSC (Digital Select Calling) capability that meets USCG SC101 and Class D Standards. 7100 USA only.•DSC (Digital Select Calling) capability that meets EC Class D Standards. 7100 EC only.•DISTRESS call button to automatically transmit the MMSID and position until an acknowledgement is received•easy access to a buddy list of up to 20 favourite people•MMSID storage for three favourite groups •Group Call and All Ships Call facility•LL position polling details•Weather alert facility. 7100 USA only.•ATIS facility for inland waterways. 7100 EC only.1.2 CUSTOMIZING YOUR NAVMAN VHF RADIOYou can customize the NAVMAN VHF radio to suit your individual preferences. Some preferences can be set directly through the keys as explained in this chapter.Other preferences are set up through the built-in menus and these are explained in the other chapters.
61.3 HOW TO DISPLAY AND NAVIGATE MENUS1. Hold down MENU (or CALL MENU). Note that only four menu items can be displayed at any one time on the LCD.2. Press + CH - to scroll up and down the menu until the cursor is postioned at the desired option. Press ENT to display that option.3. Make any entries or changes as explained in the following section. 4. Press ENT to confirm changes. Otherwise, press ESC to keep the original entry. 5. Press ESC to exit from the screen. Any changes are active as soon as you exit the screen.1.4 HOW TO ENTER ALPHANUMERIC DATAIf your NAVMAN VHF radio does not have the optional alphanumeric microphone, use the + CH - key to enter alphanumeric data.Press + to count through numbers, or hold down to scroll rapidly to the desired number.Press - to step through the alphabet, or hold down to scroll rapidly to the desired character.1.5 LCD SYMBOLS AND MEANINGSThis simulation shows the locations of all the following information symbols:
7Symbol MeaningTX Transmitting. HI LO Transmission power. High (HI) 25W or Low (LO) 1W.WX Weather channel.WX ALT Weather Alert. Alarm beeps will sound. 7100 USA only.BUSY Receiver busy with an incoming signal.PRI Priority channel is selected.D Duplex operation. Otherwise, blank for Simplex operation.LOCAL Local calling is selected. Otherwise, blank for distance calling.DSC DSC capability is available. 7100 USA and 7100 EC only. Incoming DSC call. Low Battery warning.88 Channel selected. USA INT CAN Selected channel bank for VHF radio operations and regulations.X Channel is temporarily deleted from the ALL SCAN operation.B A Channel suffix, if applicable.CH1 CH2 CH3 Shows which of the 3 favourite channels, if any, are selected. Otherwise blank.ATIS Enabled for use in inland waterways. Otherwise blank. 7100 EC only. A typical operational display is shown here. The latitude and longitude of the vessel and the time are shown. Local calling is selected. A transmission on Channel 16 is being made at high power using the International channel bank. Channel 16 is set as the Priority channel. It is also set as favourite channel 1.There is an incoming DSC call so the receiver is busy.
81.6 BASIC OPERATION AND KEY FUNCTIONSAll possible keys and their functions are listed. Note that some of the keys are not available depending on your NAVMAN VHF radio model.Key FunctionVOL/PWR Volume and Power. Turn clockwise to power on. Continue to turn until a comfortable volume is reached. VOL/PWR will also adjust the settings of an external speaker, if connected. SQL Squelch and Threshold Level. Sets the threshold level for the minimum receiver signal. Turn fully counterclockwise until random noise is heard, then turn slowly clockwise until the random noise disappears. Make another 1/4 turn clockwise for best reception in open sea conditions. In areas of high noise (eg close to large cities) reception may improve if sensitivity is reduced. Either turn SQL slowly clockwise or use the LOCAL setting. See section 2.4.16/9 Priority Channel. 7100 USA only. Also on the microphone. Press to cancel all other modes and to tune into the priority channel. Press again to return to your original channel. The default is Channel 16. To make Channel 09 the priority channel, hold down 16/9 until a beep sounds and 09 is displayed. 16 Priority Channel. 7100 EC and 7000 only. Also on the microphone. Press to cancel all other modes and to tune into the priority channel, Channel 16, on high power. Press again to return to your original channel.WX Weather Channel. 7100 USA and 7000 only. In USA and Canadian waters, press to hear the most recently selected weather station. The WX symbol is displayed on the LCD.
9 Press + or - to change to a different weather channel. Press WX, then 16/9, then CALL MENU to leave the weather channels and return to the most recent channel. If a weather alert is broadcast when you are in SCAN mode, it is picked up automatically and the alarm sounds. Press any key to hear the weather alert.H/L Transmission Power. High (HI) 25W or Low (LO) 1W. Press to toggle between high or low transmission power for the entire channel bank. The HI or LO selection is shown on the LCD. Some channels allow only low power transmissions. Error beeps will sound if the power transmission setting is incorrect. Press H/L to change it. Some channels allow only low power transmissions intially, but can be changed to high power by holding down H/L and PTT at the same time. See Appendix C for a complete listing of channel charts.3CH Three Favourite Channels. Also on the microphone. Press to toggle between your favourite channels. The CH1, CH2, or CH3 symbol appears on the LCD to show which favourite channel is selected. To add a favourite channel for the first time, select that channel then hold 3CH to store it in the CH1 location. Repeat the procedure to store two more favourite channels in the CH2 and CH3 locations respectively. If you try and add another favourite channel it will overwrite the existing CH3. CH1 and CH2 remain unless you delete them. To delete a favourite channel, select that channel then hold down 3CH until the CH1, CH2 or CH3 symbol disppears off the LCD.UIC Channel Bank. 7100 USA only. Press to toggle between USA, International or Canadian channel banks. The selected channel bank is displayed on the LCD. All the channel charts are shown in Appendix C. U/I Channel Bank. 7000 only. Press to toggle between channel banks. Note that the channel banks available are dependent upon your VHF radio model. The selected channel bank is displayed on the LCD. All the channel charts are shown in Appendix C.DIM Backlighting. 7100 EC only. Press to toggle between the backlighting settings. OFF will extinguish all the backlighting except for the DISTRESS key. (Otherwise, use the menu to change the backlight setting.)SCAN Scan. Press to scan between your current channel and the priority channel in Dual Watch mode. The weather channel is also scanned if the USA channel bank is selected. Hold down SCAN to enter ALL SCAN mode where the priority channel is checked every 1.5 seconds.
10 When a signal is received, scanning stops at that channel and BUSY appears on the LCD. If the signal ceases for more than 5 seconds, the scan restarts. Press ENT to skip over (lock out) a busy channel when in ALL SCAN mode and resume the scan. An X is shown on the LCD to designate a skipped channel. Note that it is not possible to skip over the priority channel. Press SCAN to stop at the current channel.+ CH - Channel Select. Also on the microphone. The current channel is shown on the LCD with any suffix (such as A or B) in small letters below the channel number. Press + or - to step through the available channels one at a time, or hold down to scroll rapidly through all the available channels. See Appendix C for a complete listing of channel charts. Alphanumeric Entry. This key can also be used for menu selection and for alphanumeric entry. Press + or - to scroll the cursor up or down menu options when navigating menus. To enter numbers, press + to count through the numbers or hold down to scroll rapidly to the desired number. To enter a character, press - to step through the alphabet or hold down to scroll rapidly to the desired character.ENT Enter. Use ENT when navigating menus, to confirm entries and edits. ESC Escape. Use ESC when navigating menus, to clear incorrect entries, to exit from a menu without saving changes, and to back up to the previous screen. CALL/MENU DSC Setup Menu and DSC Call Menu. 7100 USA and 7100 EC only. Press to enter the DSC Call Menu and make DSC calls. See Chapter 5. Hold down to enter the DCS Setup Menu and customize your NAVMAN VHF radio. See Chapter 4. MENU Radio menu. 7000 only. Press to enter the Radio Menu and customize your NAVMAN VHF radio. See Chapter 3.DISTRESS Send a DSC Distress Call. 7100 USA & 7100 EC only. See Chapter 6.PTT Press To Talk. Press PTT to transmit at any time. This automatically exits you from menu mode. You must release PTT to receive a signal. If PTT sticks, a built-in timer will automatically shut down a transmission after five minutes and sound the error beeps. If you have a USA 7100, note that PTT will not operate if you are in WX mode.
11Chapter 2 - The Radio Menu (MENU)2.1 RADIO MENU OPTIONS (MENU) The following options are available through MENU (or CALL MENU):Sections 1.3 and 1.4 explain how to navigate around the menu and enter, save and change data.BUDDY LISTLOCAL/DISTBACKLIGHTCONTRASTGPS/DATADSC SETUPRADIO SETUPGPS SIMULATORGPS SIMULATORGPS SIMULATORRESETCH NAME RING VOLUME INTERNAL SPKWATCH MODE WX ALERTCOM PORT USER MMSIDGROUP SETUPINDIV REPLY ATIS MMSIDATIS FUNCDSC FUNCLL REPLY MANUALSETTINGMaintain your buddy list. See Section 2.2.Set radio sensitivity. See Section 2.3.Set backlight level. See Section 2.4.Set contrast level. See Section 2.4.Set position & UTC manually.See Section 2.5. Set local time and time format. See Section 2.5. DSC Setup Menu. 7100 USA and EC models only.See Chapter 4.Radio Setup Menu. See Chapter 3.Turn the GPS Simulator on/off. See Section 2.6.Reset factory settings. See Section 2.7.Make DSC calls.7100 USA and EC models only.See Chapter 5.
122.2 MAINTAIN YOUR BUDDY LIST (BUDDY LIST)7100 USA and EC models only.Use the Buddy List to store the names and associated MMSIDs of 20 favourite people in alphanumeric order.The following sections show to use BUDDY LIST to add, edit, and delete entries on your buddy list.Chapter 3 explains how to call a buddy.2.2.1 ADD AN ENTRY1. Select BUDDY LIST.2. Press ENT again to display the list of entries. Scroll down (if required) to the first available blank line and press ENT.3. Enter the buddy name (this may be alphanumeric) then press > twice to go to the MMSID entry line.4. Enter the MMSID associated with that buddy name. This must be numeric. 5. Select SAVE & EXIT then press ENT to store the new entry, or CANCEL to exit without saving the new entry.The BUDDY LIST will arrange itself automatically into alphabetic order.Note that when the BUDDY LIST is full (20 entries), you cannot make a new entry until you have deleted an existing entry.2.2.2 EDIT AN ENTRY1. Select BUDDY LIST.2. Press ENT again to display the list of entries. Scroll down (if required) to the incorrect entry.3. Select EDIT.4. Edit the buddy name or press ENT to edit only the MMSID.5. Press ENT when you are finished.6. Choose STORE to store the changes, or EXIT to exit without saving the changes. The BUDDY LIST is displayed again.
132.2.3 DELETE AN ENTRY1. Select BUDDY LIST.2. Press ENT again to display the list of entries. Scroll down to entry that you want to delete.3. Select DELETE.4. A confirmation question (ARE YOU SURE?) is displayed. Select YES to delete the entry and return to the list of entries, or NO to keep the entry.Any deletions are effective immediately.7. If more changes are required, repeat Steps 2 thru 6. Otherwise, press ESC to exit.2.3 LOCAL OR DISTANCE SENSITIVITY (LOCAL/DST)Use LOCAL/DIST to improve the sensitivity of the receiver either locally (LOCAL) or over distances (DST). LOCAL is not recommended for use in open sea conditions. It is designed for use in areas of high radio noise, such as close to cities.See also Squelch Control (SQL) in Section 1.3.2.3.1 SET DISTANCE SENSITIVITY1. Select LOCAL/DST.2. Select DISTANT and select it to disable local sensitivity. LOCAL disappears off the LCD.2.3.2 SET LOCAL SENSITIVITY1. Select LOCAL/DST.2. Scroll to LOCAL and select it to switch on local sensitivity. LOCAL is displayed on the LCD as a reminder that local sensitivity is selected.
142.4 BACKLIGHTING (BACKLIGHT) AND CONTRAST (CONTRAST)Use BACKLIGHT to set the backlight levels for the LCD, the keypad, and the microphone at the same intensity.Use CONTRAST to set the contrast level for the LCD.2.4.1 SET THE BACKLIGHTING LEVEL1. Select BACKLIGHT.2. Select the appropriate backlight level, or off (OFF). Changes are effective when you exit from the screen. Note that the DISTRESS key backlighting cannot be switched off, even if OFF is selected.2.4.2 SET THE CONTRAST LEVEL1. Select CONTRAST.2. Select the apropriate contrast level. Changes are effective when you exit from the screen. 2.5 GPS DATA AND TIME (GPS/DATA)If the boat has an operational GPS navigation receiver, the VHF radio automatically detects and updates the vessel position and the local time. However, if the GPS navigation receiver is disconnected or absent, you can specify the vessel position and the local time manually, using the GPS/DATA option.This information is important because it will be used if a DSC distress call is transmitted.2.5.1 MANUALLY ENTER POSITION & UTC TIME (MANUAL)1. Select GPS/DATA, then MANUAL. Note that this function is available only if an operational GPS receiver is not connected.2. Enter the latitude, then the longitude, then the UTC.
153. Press ENT when all the information is correct. The vessel latitude and longitude are shown on the LCD, with the UTC time. The prefix M indicates a manual entry. 2.5.2 LOCAL TIME DISPLAY (TIME OFFSET)The local time can be set by entering the time offset between UTC and local time as follows.1. Select GPS/DATA, then SETTING. 2. Select TIME OFFSET to enter the difference between UTC and local time. Half hour increments can be used with a maximum offset of +13.5 and a minimum offset of -13.5. In this example, a difference of +1.5 hours has been entered and the local time is displayed with the suffix LOC.2.5.3 POSITION DISPLAY OPTIONS (LL DISPLAY)If you have entered the vessel position manually as described in the previous section, the vessel position is always shown on the LCD with the suffix M.However, if the time is being updated through a GPS navigation receiver, you can switch the vessel position display on the LCD on or off as follows: INSERT WORLD PICTURE SHOWING TIME ZONES OFFSET FROM UTC/GMT.
161. Select GPS/DATA, then SETTING.2. Select LL DISPLAY.2. Select ON (on) or OFF (off) as desired. In this example, OFF has been selected and so the LCD no longer shows the vessel position.2.5.4 TIME DISPLAY OPTIONS (TIME DISPLAY)If you have entered the time manually as described in the previous sections, the time is always shown on the LCD with the prefix M.However, if the vessel position is being updated through a GPS navigation receiver, you can switch the time display on the LCD on or off as follows:1. Select GPS/DATA, then SETTING.2. Select TIME DISPLAY.2. Select ON (on) or OFF (off) as desired. In this example, OFF has been selected and so the LCD no longer shows the time.If the time display is set ON, course and speed data are not displayed on the LCD (see section 2.6.6).2.5.5 TIME FORMAT OPTIONS (TIME FORMAT)Time can be shown in 12 or 24 hour format.1. Select GPS/DATA, then SETTING.2. Select TIME FORMAT.2. Select 12 Hr or 24 Hr as desired. In this example, 12 hour format has been selected and so the LCD shows the am or pm suffix.2.5.6 COURSE & SPEED DISPLAY OPTIONS (COG/SOG)Use this option to display course over ground (COG) and speed over ground
17(SOG) data on the LCD. 1. Select GPS/DATA, then SETTING.2. Select COG/SOG.2. Select ON (on) or OFF (off) as desired. In this example, ON has been selected and so the LCD shows the bearing and speed.If GOG/SOG is set ON, the time is not displayed on the LCD (see section 2.6.4). 2.5.7 GPS ALARM OPTIONS (ALARM) 7100 USA and 7100 EC only.The GPS Alarm is usually set to ON so that if the GPS navigation receiver is disconnected, the alarm sounds.1. Select GPS/DATA, then SETTING.2. Select ALARM.2. Select ON (on) or OFF (off) as desired.2.6 GPS SIMULATOR (SIMULATOR)The GPS Simulator is usually set to OFF. However, if you want to test it, turn it on. (new pictures)1. Select SIMULATOR, then select ON (on) or OFF (off) as desired.
18If the GPS Simulator is turned on, the simulated speed, bearing, and LL positions appear on the LCD as:7100 EC 11 knots moving 045º 50º 30.000N,00º 00.000E7100 USA 11 knots moving 045º25º 00.000N82º 00.000WThis data is updated automatically during the simulation.Note that it is not possible to send a transmission when in simulator mode.2.7 RESET TO FACTORY DEFAULTS (RESET)Use this to return every setting to the factory defaults except your user MMSID and the entries in your buddy list. (new picture)1. Select RESET, then select YES.
19Chapter 3 - Radio Setup Menu (RADIO SETUP)3.1 RADIO SETUP MENU (RADIO SETUP)Sections 1.3 and 1.4 explain how to navigate around the menu and enter, save and change data.3.2 CUSTOMIZE OR DELETE CHANNEL NAMES (CH NAME)The channel charts are listed in Appendix C with their default name tags. CH NAME gives you the option to edit the channel name tags displayed on your LCD, as follows:1. Select RADIO SETUP, then select CH NAME.2. Use + or - to step through the channels with their name tags until you see the channel name tag you want to change. In this example, there is no channel name tag associated with CH01.3. Select EDIT and press ENT to edit the existing name tag. Input the new name along the dashed line, then press ENT.CH NAME RING VOLUMEBEEP VOLUMEINTERNAL SPKWATCH MODE WX ALERT COM PORT Customize channel names.See Section 3.2.Switch the weather alert beeps on or off. (7100 USA only.) See section 3.6.Edit the channel name or use the default name. See section 3.5.Switch on or off any internal speakers that are connected to the VHF radio. See section 3.4.Select NMEA protocol for communications between the VHF radio and any other instruments. See section 3.7.Set the volume level of the beeps. See section 3.3.Set the volume level of the incoming call notification beeps. See section 3.3.
204. Select YES to confirm the new channel name tag. Delete a channel name as follows:1. Select RADIO SETUP, then select CH NAME.2. Use + or - to step through the channels with their name tags until you see the channel name tag you want to change. In this example, the PHONETALK name tag associated with CH02 is deleted.3. Select DELETE and press ENT. 4. Select YES to confirm the deletion. The channel is shown with no name tag.3.3 RING & BEEP VOLUME (RING VOLUME) & (BEEP VOLUME)Set the volume level of the incoming signal beeps (RING VOLUME) and/or the error and warning beeps (BEEP VOLUME) to HIGH (high) or LOW (low) as follows:1. Select RADIO SETUP, then select RING VOLUME or BEEP VOLUME as appropriate.2. Select HIGH or LOW. (The beeps will sound at the new level.)3.4 INTERNAL SPEAKER CONNECTIONS (INTERNAL SPK)If any internal speakers are connected to the VHF radio, use this menu option to switch them on or off to suit your cabin arrangements.
211. Select RADIO SETUP, then select INTERNAL SPK.2. Select ON or OFF.3.5 SET THE PRIORITY CHANNEL (WATCH MODE)If you have a VHF 7000 or a VHF 7100 EC, watch mode is similiar to a dual watch, scanning between the priority channel and the working channel. CH16 is the priority channel.However, only if you have the 7100 USA model and are operating in USA or Canadian waters, you can set the priority channel to cover both CH16 and CH09 as well as the working channel, as follows:1. Select RADIO SETUP, then select WATCH MODE.2. Select CH16 + CH09 for three channel scanning.3.6 WEATHER ALERT (WX ALERT) 7100 USA only.The NOAA provides several weather forecast channels for USA and Canadian waters. If severe weather such as storms or hurricanes are forecast, the NOAA broadcasts a weather alert. You can pick up these weather alerts, as follows:1. Select RADIO SETUP, then select Wx ALERT.2. Select ON. When a weather alert is broadcast, the alarm beeps will sound. (If
223.7 NMEA PROTOCOL (COMM PORT)The VHF radio can be added to a group of instruments using NMEA protocol.1. Select RADIO SETUP, then select COM PORT.2. Select NMEA. Specify whether CHECKSUM is on (ON) or off (OFF). CHECKSUM ON is the usual standard.
23Chapter 4 - DSC Setup Menu (DSC SETUP)These DSC facilities are available only on the VHF7100 USA and VHF7100 EC models, and a valid user MMSID must be entered to access the DSC functions.4.1 DSC SETUP - MENU OPTIONSThe following options are available: Sections 1.3 and 1.4 explain how to navigate around the menu and enter, save and change data. 4.2 ENTER YOUR USER MMSID (USER MMSID)This is a once-only operation. You must enter your user MMSID before you can access the DSC functions, as follows: Enter your user MMSID. If you do not have a user MMSID, see Appendix E.) See section 4.2. USER MMSID GROUP SETUP INDIV REPLY ATIS MMSID ATIS FUNC DSC FUNC LL REPLYEnter or change the name and/or details of a group. See section 4.3.Enter or change your ATIS MMSID (7100 EC only). See section 4.5.Enable/disable the ATIS function (7100 EC only). See section 4.5.Select the type of response to an LL request. See section 4.7.Turn DSC scanning on/off. See section 4.6.Choose an automatic or manual response to calls. See section 4.4.
24You can display and read your user MMSID at any time, but you get only one opportunity to enter your user MMSID.1. Select DSC SETUP, then USER MMSID. 2. If this is the first time that you are entering your user MMSID, a dashed line appears. Enter your user MMSID along the dashed line and press ENT when it is correct.3. Input the user MMSID again as a check, then select STORE. If the user MMSID has been entered correctly both times, it is displayed for 3 seconds on the LCD and then saved (SAVED).4.3 MAINTAIN YOUR GROUPS (GROUP SETUP)Use GROUP SETUP to create, edit, or delete 1, 2, or 3 groups of frequently called people stored in alphanumeric order. A group MMSID always starts with 0.4.3.1 CREATE A GROUP (GROUP SETUP)1. Select DSC SETUP, then select GROUP SETUP. 2. If this is the first time that you are entering a group name, a dashed line appears. Otherwise, any existing group names are displayed. Scroll down (if required) and enter the group name along the dashed line. It can be alphanumeric. 3. Enter the group MMSID. (Note that the first number is always 0.)4. The group name and group MMSID are shown in a confirmation screen. Select STORE if the entry is correct.4.3.2 EDIT GROUP NAME DETAILS (EDIT)1. Select DSC SETUP, then select GROUP SETUP.
252. Select the group, then select EDIT.3. Make the changes to the group name and/or to the group MMSID.4. Select STORE to store the changes.4.3.3 DELETE A GROUP1. Select DSC SETUP, then select GROUP SETUP.2. Select the group, then select DELETE OK.3. Press ENT to confirm the deletion.4.4 RESPONSE TO INDIVIDUAL CALLS (INDIV REPLY)You can respond to incoming individual calls with an automatic response or with a manual response.An automatic response sends an acknowledgement and then sets the request link channel, ready for a conversation.A manual response asks if you want to acknowlege the call, and then asks if you want to converse with the caller.1. Select DSC SETUP, then select INDIV REPLY.2. Select AUTO for an automatic response, or MANUAL for a manual response.4.5 ATIS MMSID AND ATIS FUNCTIONALITY (ATIS FUNC)7100 EC only. You must enter your ATIS MMSID to access ATIS functionality if you are navigating inland waterways within Europe. 4.5.1 ENTER OR EDIT THE ATIS MMSIDTo enter or edit your ATIS MMSID:1. Select DSC SETUP, then ATIS MMSID.
262. If this is the first time that you are entering your ATIS MMSID, a dashed line appears. Enter your ATIS MMSID here and select STORE. The first number is always 9. If you are editing an existing ATIS MMSID, this will be displayed. Make the required changes.3. Input the ATIS MMSID again as a check. Press ENT and select SAVED. If the user MMSID has been entered correctly both times, it is displayed for 3 seconds on screen and then stored.4.5.2 ENABLE ATIS FUNCTIONALITY (ATIS FUNC)7100 EC only. ATIS functionality will operate only after the ATIS MMSID has been entered (see previous section). 1. Select DSC SETUP, then ATIS FUNC.2. Select ON to enable the ATIS functionality and automatically disable DSC functionality. A warning message will appear: WARNING DSC OFF.(Note that it is not possible to have both ATIS ON and DSC ON simultaneously. When you enable one, the transceiver will automatically disable the other and display a warning message.) 4.6 DSC FUNCTIONALITY OPTIONS (DSC FUNC)DSC functionality can be disabled but this is not recommended. 1. Select DSC SETUP, then DSC SCAN.2. Select ON to operate the DSC functionality. (This will automatically disable ATIS functionality on the 7100 EC and a warning message will appear: WARNING ATIS OFF.)(Note that it is not possible to have both ATIS ON and DSC ON simultaneously on the 7100 EC. When you enable one, the transceiver will automatically disable the other and display a warning message.) 4.7 RESPONSE TYPE TO LL CALLS (LL REPLY)You can set up the VHF 7100 to respond to an LL request in one of four ways.AUTO - automatically reply to any incoming LL request.AUTO BUDDY - automatically reply to any incoming call from anyone in your buddy list or a group list.MANUAL - choose whether to reply or not.OFF - switch off notification of any incoming LL requests.
27Chapter 5 - Sending and Receiving DSC Calls5.1 WHAT IS DSC?DSC (Digital Selective Calling) is a semi-automated method of establishing VHF, MF, and HF radio calls. It has been designated as an international standard by the IMO (International Maritime Organization) and is part of the GMDSS (Global Maritime Distress and Safety System). Currently, you are required to monitor Distress Channel 16, but DSC will eventually replace listening watches on distress frequencies and will be used to broadcast routine and urgent maritime safety information. DSC enables you to send and receive calls from any vessel or coast station that is equipped with DSC functionality, and within geographic range. Calls can be categorised as distress, urgency, safety, or routine, and DSC selects a working channel automatically.5.2 SENDING DSC CALLS1. Press CALL MENU to show the types of DSC call that can be made. Note that only four DSC call types can be shown at any one time on the LCD menu.2. Press + or - to scroll up and down the DSC call types until the cursor is postioned at the desired option. Then press ENT. The DSC call types are:These DSC facilities are available only on the VHF7100 USA and VHF7100 EC models, and a valid user MMSID must have been entered to access the INDIVIDUALINDIV ACKLAST GROUPALL SHIPSCALL LOGDISTRESS LOGMake a manual call or reply to a new caller or a buddy.See Section 5.2.1 and 5.2.2.Make a call to one of your three groups. See Section 5.2.5.Show the details of the most recent incoming call.See Section 5.2.4.Make an urgent, safety, or routine call to all ships USA??See Section 5.2.6.Show the details of the 20 most recent incoming calls.See Section 5.2.7.Show the details of the 20 most recent distress calls.See Section 5.2.8.See Section 5.2.3 TBS
285.2.1 MAKE A ROUTINE CALL MANUALLY (INDIV REPLY)If you chose to respond manually to individual calls when you set up your DSC options (see Section 3.5), you must enter the caller’s MMSID or select the buddy name, and then specify the calling channel.1. When the incoming call is complete, press CALL MENU to enter DSC mode, then select INDIVIDUAL.2. If the caller is not in your buddy list, select MANUAL MMSID and then enter the MMSID of the caller along the dashed line. If the caller is in your buddy list, just scroll down the list of buddies and select that buddy.3. Now specify the calling channel using the + and - key and monitor that channel briefly to ensure that it is clear before you transmit. (This is an FCC requirement.) If it is busy, select a different calling channel. NOTE: If the call is from a coast station, the VHF 7100 will recognise this and automatically specify a channel.4. The VHF 7100 summarises the call data and asks if it should send the call (SEND?). Press ENT to send the call and CALLING appears on the LCD. 5. If the call is acknowledged (ACKNOWLEDGED), press to talk when invited (PRESS PTT TO TALK).6. If there is no reply (UNABLE TO ACKNOWLEDGE), retry the call (see Section 5.2.2).5.2.2 RETRYING A ROUTINE CALL
291. If there is no reply to your call after one minute (UNABLE TO ACKNOWLEDGE) the VHF 7100 asks if you want to retry the call (SEND AGAIN?).2. Select YES and press ENT to retry the call. The VHF 7100 will repeat this cycle twice. If the call still cannot be placed, the VHF 7100 returns to normal operation.5.2.3 ACKNOWLEDGE AN INDIVIDUAL CALL (INDIV ACK)TBS. OR is this VHF 7200 specific?5.2.4 RECALL THE MOST RECENT INCOMING CALL (LAST)The VHF 7100 stores the contact details of your most recent incoming call, so that you can call up quickly, if necessary.1. Press CALL MENU to enter DSC mode, then select LAST CALL. The VHF 7100 displays the contact details of the most recent incoming call.2. Press ENT to send a call to that contact, then set the channel and continue as explained in Section 5.2.1.5.2.5 CALL A GROUP (GROUP)1. Press CALL MENU to enter DSC mode, then select GROUP CALL. The VHF 7100 displays the names of your groups.2. Select the group that you want to call, then set the channel and continue as explained in Section 5.2.1.
305.2.6 CALL ALL SHIPS (ALL SHIPS)1. Press CALL MENU to enter DSC mode, then select ALL SHIPS.2. The priority is set automatically to URGENT. However, if you have a VHF 7100 USA, you can select one of the following call priorities: URGENT - for use when a serious situation or problem arises that could lead to a distress situation SAFETY - to send safety information to all other vessels in range; ROUTINE - routine call.3. The VHF 7100 asks for confirmation of the all ships call. Select YES and press ENT to transmit the call. Continue as explained in Section 5.2.1.5.2.7 CALL USING THE CALL LOG (CALL LOG)The Call Log contains the contact details for the 20 most recent incoming calls, so that you call any of them again quickly.1. Press CALL MENU to enter DSC mode, then select CALL LOG. Scroll down to the desired contact details. The VHF 7100 displays the contact details for the most recent incoming call as the first entry (01) in the call log. In the example, the contact details for the 11th most recent call are displayed. 2. Set the channel and continue as explained in Section 5.2.1.
315.2.8 CALL USING THE DISTRESS LOG (DISTRES LOG)The Distress Log contains the contact details for the 10 most recently received distress calls, so that you can call any of them quickly. Always try to make voice contact on CH16 first, as follows:1. Press CALL MENU to enter DSC mode, then select DISTRES LOG. 2. Scroll down to the distress call entry that you want to call. The VHF 7100 displays the details for the most recently received distress call as the first entry (01) in the distress log. The details are displayed over two screens that alternate every 1.5 seconds; the first screen shows the user MMSID and location, and the second screen shows the user MMSID and the nature and time of the emergency (if specified). 3. Set the channel and continue as explained in Section 5.2.1.
325.3 RECEIVING DSC CALLSFive types of DSC calls can be received from vessels within range at various priority levels: DISTRESS - see Chapter 5.ALL SHIPS - Urgency, or Safety priority (see Section 5.3.1)INDIVIDUAL - Urgency, Safety, or Routine priority (see Section 5.3.2)GROUP - Routine priority only (see Section 5.3.3)In addition to the audible alert, the telephone icon will flash on the LCD. 5.3.1 RECEIVING AN ALL SHIPS CALL (ALL SHIPS)1. When you receive notification of an ALL SHIPS call, press any key to cancel the alert. The VHF 7100 automatically selects CH16. The priority level and the user MMSID are displayed on the LCD. If the VHF 7100 recognises the user MMSID as one of your buddies, the buddy’s name is displayed in place of the user MMSID.2. You do not need to send an acknowledgement. If necessary, press PTT to initiate voice contact on CH16 and then switch to a working channel.The call data is stored in the Call Log (see Section 5.2.7). 5.3.2 RECEIVING AN INDIVIDUAL CALL (INDIVIDUAL)1. When you receive notification of an INDIVIDUAL call, press any key to cancel the alert. The VHF 7100 automatically selects the channel designated in the incoming call. In the example, an individual routine call has selected CH72. However, safety and urgency priority level calls always select CH16. The priority level and the user MMSID are displayed on the LCD. If the VHF 7100 recognises the user MMSID as one of your buddies, the buddy’s name is displayed in place of the user MMSID.2. The VHF 7100 prompts you to press ENT to acknowledge the incoming call (PRESS ENTER TO ACK BACK!). 3. Press ENT, then the caller should respond to your acknowledgement by making voice contact on the designated channel. If this does not happen, you can press PTT to initiate voice contact instead. The call data is stored in the Call Log (see Section 5.2.7).
335.3.3 RECEIVING A GROUP CALL (GROUP CALL)1. When you receive notification of a GROUP call, press any key to cancel the alert. The VHF 7100 automatically selects the channel designated in the incoming call. The priority level is always routine, and the group is identified on the LCD. The group will be one of the three groups of frequently called people that you set up earlier (see Section 3.4).2. You do not need to send an acknowledgement. If desired, press PTT to initiate voice contact on the designated channel.The call data is stored in the Call Log (see Section 5.2.7).
34Chapter 6 - Distress Calls6.1 SENDING A DISTRESS CALL 1. Open the red cover labelled DISTRESS. If time is available to specify the nature of the distress, go to step 2. Otherwise, go directly to step 3.2. Press the DISTRESS key to display the following categories. Scroll to the category that describes your situation, then press ENT:UNDEFINEDFIRE FLOODINGCOLLISIONGROUNDINGLISTINGSINKINGADRIFTABANDONINGPIRACYMAN IN WATEREPRIB 3. Hold down the DISTRESS key for about 3 seconds, until you see the distress call sent message (DISTRES CALL SENT!) on the LCD. The whole display starts to flash and beep. The distress call repeats five times continuously. It then repeats randomly every 3.5 to 4.5 minutes until a distress acknowledgement (DISTRESS ACK) is received from a search and rescue authority or until you cancel the distress call manually. The VHF 7100 selects CH16 automatically so that you can hear any incoming voice contacts from search and rescue authorities or other vessels within range. Press ESC if you need to cancel the distress call. This is the only key that operates in distress mode. This DSC facility is available only on the VHF7100 USA and VHF7100 EC models, and a valid user MMSID must have been entered to access this DSC function.
356.2 RECEIVING A DISTRESS CALL (DISTRESS!) An alert sounds when a distress call (DISTRESS!) is received. The VHF 7100 automatically selects CH16 and displays the details of the distress call on the LCD.The details are displayed over two screens that alternate every 1.5 seconds; the first screen shows the user MMSID and location (if specified), and the second screen shows the user MMSID and the nature and time of the emergency (if specified).If the location and time are not specified, these are replaced with sequences of 9s and 8s respectively. In this example, the location has not been specified.1. Press any key to cancel the alert. You do not need to send an acknowledgement.2. Press PTT to establish voice contact.6.3 DISTRESS ACKNOWLEDGEMENT OR RELAY (DISTRESS ACK) An alert sounds when a distress acknowledgement or relay (DISTRESS ACK) is received. The VHF 7100 automatically selects CH16 and displays the details of the distress call on the LCD.The details are displayed over two screens that alternate every 1.5 seconds; the first screen shows the user MMSID and location (if specified), and the second screen shows the user MMSID and the nature and time of the emergency (if specified).If the location and time are not specified, these are replaced with sequences of 9s and 8s respectively. In this example, the location has not been specified.1. Press any key to cancel the alert. You do not need to send an acknowledgement.2. Maintain a listening watch on CH16 and standby to lend assistance.
36NAVMAN VHF 7000 GENERALPower Supply: 13.6V DC. Current drain:Transmit 6A at 25W Tx / 1.5A at 1W TxReceive Less than 250mA in standbyUseable channels: International, USA (country specific)Mode: 16K0G3E (FM)PHYSICALLCD display (viewing): 41(H) x 53(W) mm FSTN 4 x 12 characterContrast andDimming control: Yes Antenna connector: SO-239 (50 ohm)Temperature Range: -15ºC to +50ºCWaterproof: JIS-7Dimensions: 161(W) x 75(H) x 147(D) mm - without bracketWeight: 1.29kg (2.8lbs) - without microphoneFrequency stability: +/- 10ppmFrequency control: PLLGPS/NMEA input: YesComm. port: 4800 baud NMEADSC: NoFEATURESFlush Mount kit and dust cover: YesLocal/Distant control: YesPosition polling: NoTrack-your-buddy: NoCall logs: NoDSC (USCG SC101 and Class D): NoChannel Naming: YesTri watch, Favourite channel scan, All scan: YesUser programmable MMSID: NoMMSID and NAMEdirectory: NoTRANSMITTERFrequency: 156.025 - 157.425MHzOutput power: 25W / 1W selectableTransmitter protection: Open / short circuit of antennaAppendix A - Technical Specifications
37Max Freq deviation: +/- 5kHzSpurious & harmonics: 80dB@25W, 60dB@1WModulation distortion: Less than 4%@ 1kHz for a +/-3kHz deviation RECEIVERFrequency: 156.025 - 163.275MHz12dB SINAD sensitivity: 0.25uV (distant) / 2.5uV (local)20db SINAD sensitivity: 0.35uVAdjacent CH selectivity:more than 70dBSpurious response: more than 70dbIntermodulationRejection ratio: more than 68dBResidual Noise level: more than -40dB unsquelchedAudio output power: 2W (with 8 ohm at 10% distortion) 4W with 4 ohm external speakerCompass safe distance: 0.Xm TBSSpecifications are subject to change without notice.NAVMAN VHF 7100 GENERALPower Supply: 13.6V DC. Current drain:Transmit 6A at 25W Tx / 1.5A at 1W TxReceive Less than 250mA in standbyUseable channels: International, USA, Canada, Weather (country specific)Mode: 16K0G3E (FM) / 16K0G2B (DSC)PHYSICALLCD display (viewing): 41(H) x 53(W) mm FSTN 4 x 12 characterContrast andDimming control: Yes Antenna connector: SO-239 (50 ohm)Temperature Range: -15ºC to +50ºCWaterproof: JIS-7Dimensions: 161(W) x 75(H) x 147(D) mm - without bracketWeight: 1.29kg (2.8lbs) - without microphoneFrequency stability: +/- 10ppmFrequency control: PLLGPS/NMEA input: YesComm. port: 4800 baud NMEADSC: YesFEATURESFlush Mount kit and dust cover: YesLocal/Distant control: YesPosition polling: Yes
38Track-your-buddy: NoCall logs: Yes - 20 individual and 20 distressDSC (USCG SC101 and Class D): Yes (7100 USA)Channel Naming: YesTri watch, Favourite channel scan, All scan: YesUser programmable MMSID: YesMMSID and NAMEdirectory: Yes - 20 numbers & groupTRANSMITTERFrequency: 156.025 - 157.425MHzOutput power: 25W / 1W selectableTransmitter protection: Open / short circuit of antennaMax Freq deviation: +/- 5kHzSpurious & harmonics: better than 2.5µWModulation distortion: Less than 4%@ 1kHz for a +/-3kHz deviation RECEIVERFrequency: 156.025 - 163.275MHz12dB SINAD sensitivity: 0.25uV (distant) / 2.5uV (local)20db SINAD sensitivity: 0.35uVAdjacent CH selectivity:more than 65dBSpurious response: more than 65dbIntermodulationRejection ratio: more than 65dBResidual Noise level: more than -40dB unsquelchedAudio output power: 2W (with 8 ohm at 10% distortion) 4W with 4 ohm external speakerCompass safe distance: 0.Xm TBSSpecifications are subject to change without notice.
39Appendix B - Troubleshooting1. The transceiver will not power up. A fuse may have blown OR there is no voltage getting to the transceiver.a) Check the power cable for cuts, breaks, or squashed sections.b) Replace the fuse (2 spare fuses are supplied).c) Check the battery voltage. This must be greater than 10.5V.2. The transceiver blows the fuse when the power is switched on. The power wires may have been reversed. a) Check that the red wire is connected to the positive battery terminal, and the black wire is connected to the negative battery terminal.3. The speaker makes popping or whining noises when the engine is running. Electrical noise may be interfering with the transceiver.a) Re-route the power cables away from the engine.b) Add a noise suppressor to the power cable.c) Use resistive spark plug wires and/or use an alternator whine filter.4. No sound from the external speaker.a) Check that the external speaker cable is physically connected.b) Check the polarity of the external speaker cable.5. Transmissions are always on low power, even when high (HI) power is selected. The antenna may be faulty.a) Test the transceiver with a different antenna.b) Have the antenna checked out.6. Battery symbol is displayed. The power supply is too low or too high.a) Check the battery voltage. This should be between 10.5V and ???b) Check the generator.7. No position information is displayed. The GPS cable may faulty or the GPS setting may be incorrect. a) Check that the GPS cable is physically connected.b) Check the polarity of the GPS cable.c) Check the baud rate setting of the GPS if applicable. The baud rate setting should be 4800 and parity should be set to NONE.
40Appendix C - VHF Marine Channel ChartsC.1 INTERNATIONAL CHANNEL CHARTCH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG01 156.050 160.650 Public Correspondence, Duplex No Yes TELEPHONE02 156.100 160.700 Public Correspondence, Duplex No Yes TELEPHONE03 156.150 160.750 Public Correspondence, Duplex No Yes TELEPHONE04 156.200 160.800 Port Operations, Duplex No Yes PORT OPS05 156.250 160.850Port Operations, Selected VTS AreasNo Yes PORT OPS/VTS06 156.300 156.300 Inter-ship Safety Yes No SAFETY07 156.350 160.950 Port Operations, Duplex No Yes PORT OPS08 156.400 156.400 Commercial (inter-ship only) Yes No COMMERCIAL09 156.450 156.450 Recreational Calling Channel Yes Yes CALLING10 156.500 156.500 Commercial Yes Yes COMMERCIAL11 156.550 156.550 Commercial, VTS in Selected Areas Yes Yes VTS12 156.600 156.600Port Operations, Selected VTS AreasYes Yes PORT OPS/VTS13 156.650 156.650 Intership Navigation Safety (bridge-to-bridge)Yes No BRIDGE COM14 156.700 156.700Port Operations, Selected VTS AreasYes Yes PORT OPS/VTS15 1156.750 156.750 Port Operations – 1W Only Yes Yes PORT OPS16 156.800 156.800 International Distress, Safety, and CallingYes Yes DISTRESS17 1156.850 156.850 State Controlled – 1W Only Yes Yes SAR18 156.900 161.500 Port Operations, Duplex No Yes PORT OPS19 156.950 161.550 Commercial, Duplex No Yes SHIP - SHORE20 157.000 161.600 Port Operations, Duplex No Yes PORT OPS21 157.050 161.650 Port Operations, Duplex No Yes PORT OPS22 157.100 161.700 Port Operations, Duplex No Yes PORT OPS23 157.150 161.750 Public Correspondence, Duplex No Yes TELEPHONE24 157.200 161.800 Public Correspondence, Duplex No Yes TELEPHONE25 157.250 161.850 Public Correspondence, Duplex No Yes TELEPHONE26 157.300 161.900 Public Correspondence, Duplex No Yes TELEPHONE27 157.350 161.950 Public Correspondence, Duplex No Yes TELEPHONE28 157.400 162.000 Public Correspondence, Duplex No Yes TELEPHONE
41CH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG61 156.075 160.675 Port Operations, Duplex No Yes PORT OPS62 156.125 160.725 Port Operations, Duplex No Yes PORT OPS63 156.175 160.775 Port Operations, Duplex No Yes PORT OPS64 156.225 160.825 Public Correspondence, Duplex No Yes TELEPHONE65 156.275 160.875 Port Operations, Duplex No Yes PORT OPS66 156.325 160.925 Port Operations, Duplex No Yes PORT OPS67 156.375 156.375 Commercial, bridge-to-bridge Yes No BRIDGE COM68 156.425 156.425 Boat Operations, Recreational Yes No SHIP - SHIP69 156.475 156.475 Port Operations Yes Yes PORT OPS70 3156.525 156.525 Digital Selective Calling - DSC ------ ------ DSC71 156.575 156.575 Port Operations Yes Yes PORT OPS72 156.625 156.625 Intership Yes No SHIP - SHIP73 156.675 156.675 Port Operations Yes Yes PORT OPS74 156.725 156.725 Port Operations Yes Yes PORT OPS77 156.875 156.875 Intership Yes No SHIP - SHIP78 156.925 161.525 Non-Commercial, Duplex No Yes SHIP - SHORE79 156.975 161.575 Commercial, Duplex No Yes SHIP - SHORE80 157.025 161.625 Commercial, Duplex No Yes SHIP - SHORE81 157.075 161.675 Port Operations, Duplex No Yes PORT OPS82 157.125 161.725 Port Operations, Duplex No Yes PORT OPS83 157.175 161.775 Public Correspondence, Duplex No Yes TELEPHONE84 157.225 161.825 Public Correspondence, Duplex No Yes TELEPHONE85 157.275 161.875 Public Correspondence, Duplex No Yes TELEPHONE86 157.325 161.925 Public Correspondence, Duplex No Yes TELEPHONE87 157.375 161.975 Public Correspondence, Duplex No Yes TELEPHONE88 157.425 162.025 Public Correspondence, Duplex No Yes TELEPHONE60 156.025 160.625 Public Correspondence, Duplex No Yes TELEPHONE
42WEATHER MHz TRAFFIC TYPE NAME TAGWx01 RX Only 162.550 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx02 RX Only 162.400 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx03 RX Only 162.475 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx04 RX Only 162.425 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx05 RX Only 162.450 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx06 RX Only 162.500 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx07 RX Only 162.525 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx08 RX Only 161.650 CANADIAN WEATHER CHANNEL ------ ------ CANADA WXWx09 RX Only 161.775 CANADIAN WEATHER CHANNEL ------ ------ CANADA WXWx10 RX Only 163.275 NOAA WEATHER CHANNEL ------ ------ NOAA WXSPECIAL NOTES ON INTERNATIONAL CHANNEL USAGE1. LOW POWER (1W) only.2. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.3. Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.4. The INTERNATIONAL mode is not legal for use in U.S. or Canada waters.
43C.2 USA CHANNEL CHARTCH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG01A 156.050 156.050Port Operations, Selected VTS AreasYes Yes PORT OPS/VTS03A 4156.150 156.150 US Government, Coast Guard Yes Yes UNAUTHORIZED05A 156.250 156.250Port Operations, Selected VTS AreasYes Yes PORT OPS/VTS06 156.300 156.300 Inter-ship Safety Yes No SAFETY07A 156.350 156.350 Commercial Yes Yes COMMERCIAL08 156.400 156.400 Commercial (inter-ship only) Yes No COMMERCIAL09 156.450 156.450 Recreational Calling Channel Yes Yes CALLING10 156.500 156.500 Commercial Yes Yes COMMERCIAL11 156.550 156.550 Commercial, VTS in Selected AreasYes Yes VTS12 156.600 156.600Port Operations, Selected VTS AreasYes Yes PORT OPS/VTS13 3156.650 156.650 Intership Navigation Safety (bridge-to-bridge), 1W with Power-upYes No BRIDGE COM14 156.700 156.700Port Operations, Selected VTS AreasYes Yes PORT OPS/VTS15 2RX Only 156.750 Environmental, RX Only ------ ------ ENVIROMENTAL16 156.800 156.800 International Distress, Safety, and CallingYes Yes DISTRESS17 1156.850 156.850 State Controlled – 1W Only Yes Yes SAR18A 156.900 156.900 Commercial Yes Yes COMMERCIAL19A 156.950 156.950 Commercial Yes Yes COMMERCIAL20 157.000 161.600 Port Operations, Canadian Coast Guard, DuplexNo Yes PORT OPS20A 157.000 157.000 Port Operations Yes Yes PORT OPS21A 4157.050 157.050 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED22A 157.100 157.100 Coast Guard Liaison Yes Yes COAST GUARD23A 4157.150 157.150 U.S. Government, Coast Guard Yes Yes UNAUTHORIZED24 157.200 161.800 Public Correspondence, Marine OperatorNo Yes TELEPHONE25 157.250 161.850 Public Correspondence, Marine OperatorNo Yes TELEPHONE26 157.300 161.900 Public Correspondence, Marine OperatorNo Yes TELEPHONE27 157.350 161.950 Public Correspondence, Marine OperatorNo Yes TELEPHONE28 157.400 162.000 Public Correspondence, Marine OperatorNo Yes TELEPHONE
44CH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TOSHORENAME TAG61A 4156.075 156.075 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED63A 156.175 156.175 Port Operations, VTS in Selected AreasYes Yes PORT OPS/VTS64A 4156.225 156.225 U.S. Government, Canadian Commercial FishingYes Yes UNAUTHORIZED65A 156.275 156.275 Port Operations Yes Yes PORT OPS66A 156.325 156.325 Port Operations Yes Yes PORT OPS67 3156.375 156.375 Commercial, bridge-to-bridge, 1W with Power-upYes No BRIDGE COM68 156.425 156.425 Boat Operations, Recreational Yes No SHIP - SHIP69 156.475 156.475 Boat Operations, Recreational Yes Yes PLEASURE70 6156.525 156.525 Digital Selective Calling - DSC ------ ------ DSC71 156.575 156.575 Boat Operations, Recreational Yes Yes PLEASURE72 156.625 156.625 Boat Operations, Recreational Yes No SHIP - SHIP73 156.675 156.675 Port Operations Yes Yes PORT OPS74 156.725 156.725 Port Operations Yes Yes PORT OPS77 1156.875 156.875 Port Operations –1W Only Yes Yes PORT OPS78A 156.925 156.925 Boat Operations, Recreational Yes No SHIP - SHIP79A 156.975 156.975 Commercial Yes Yes COMMERCIAL80A 157.025 157.025 Commercial Yes Yes COMMERCIAL81A 4157.075 157.075 U.S. Government, Environmental Protection Agency OperationsYes Yes UNAUTHORIZED82A 4157.125 157.125 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED83A 4157.175 157.175 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED84 157.225 161.825 Public Correspondence, Marine OperatorNo Yes TELEPHONE85 157.275 161.875 Public Correspondence, Marine OperatorNo Yes TELEPHONE86 157.325 161.925 Public Correspondence, Marine OperatorNo Yes TELEPHONE87 157.375 161.975 Public Correspondence, Marine OperatorNo Yes TELEPHONE88 157.425 162.025 Public Correspondence, Marine OperatorNo Yes TELEPHONE88A 157.425 157.425 Commercial, Intership Only Yes No COMMERCIAL
45WEATHER MHz TRAFFIC TYPE NAME TAGWx01 RX Only 162.550 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx02 RX Only 162.400 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx03 RX Only 162.475 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx04 RX Only 162.425 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx05 RX Only 162.450 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx06 RX Only 162.500 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx07 RX Only 162.525 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx08 RX Only 161.650 CANADIAN WEATHER CHANNEL ------ ------ CANADA WXWx09 RX Only 161.775 CANADIAN WEATHER CHANNEL ------ ------ CANADA WXWx10 RX Only 163.275 NOAA WEATHER CHANNEL ------ ------ NOAA WXSPECIAL NOTES ON USA CHANNEL USAGE1. LOW POWER (1W) only.2. Receive Only.3. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.4. Lightly Shaded Simplex channels 03A, 21A, 23A, 61A, 64A, 81A, 82A, and 83A cannot be lawfully used in U.S. waters unless special authorization is obtained from the U.S. Coast Guard. Not for use by the general public.5. The letter “A” illuminated by the channel number indicates the USA channel is simplex. This same channel is always duplex when selecting International. There is no “A” reference for International channels. The letter “B” is only used for some Canadian “Receive Only” channels.6. Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.
46C.3 CANADA CHANNEL CHARTCH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG01 156.050 160.650 Public Correspondence, Duplex No Yes TELEPHONE02 156.100 160.700 Public Correspondence, Duplex No Yes TELEPHONE03 156.150 160.750 Public Correspondence, Duplex No Yes TELEPHONE04A 156.200 156.200 Canadian Coast Guard, SAR Yes Yes CANADIAN CG05A 156.250 156.250 Port Operations, VTS in Selected AreasYes Yes PORT OPS/VTS06 156.300 156.300 Inter-ship Safety Yes No SAFETY07A 156.350 156.350 Commercial Yes Yes COMMERCIAL08 156.400 156.400 Commercial (inter-ship only) Yes No COMMERCIAL09 156.450 156.450 Recreational Calling Channel Yes Yes CALLING10 156.500 156.500 Commercial Yes Yes COMMERCIAL11 156.550 156.550 Commercial, VTS in Selected AreasYes Yes VTS12 156.600 156.600 Port Operations, VTS in Selected AreasYes Yes PORT OPS/VTS13 3156.650 156.650 Intership Navigation Safety (bridge-to-bridge)Yes No BRIDGE COM14 156.700 156.700 Port Operations, VTS in Selected AreasYes Yes PORT OPS/VTS15 1156.750 156.750 Commercial – 1W Only Yes Yes COMMERCIAL16 156.800 156.800 International Distress, Safety, and CallingYes Yes DISTRESS17 1156.850 156.850 State Controlled – 1W Only Yes Yes SAR18A 156.900 156.900 Commercial Yes Yes COMMERCIAL19A 156.950 156.950 Canadian Coast Guard Yes Yes CANADIAN CG20 1157.000 161.600 Canadian Coast Guard, Duplex– 1W OnlyNo Yes CANADIAN CG21 157.050 161.650 Port Operations, Duplex No Yes PORT OPS21A 157.050 157.050 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED21B RX Only 161.650 Port Operations, RX Only ------ ------ PORT OPS22A 157.100 157.100 Canadian Coast Guard Liaison Yes Yes CANADIAN CG23 157.150 161.750 Public Correspondence, Duplex No Yes TELEPHONE24 157.200 161.800 Public Correspondence, Duplex No Yes TELEPHONE25 157.250 161.850 Public Correspondence, Duplex No Yes TELEPHONE25B RX Only 161.850 Public Correspondence, RX Only ------ ------ TELEPHONE26 157.300 161.900 Public Correspondence, Duplex No Yes TELEPHONE27 157.350 161.950 Public Correspondence, Duplex No Yes TELEPHONE28 157.400 162.000 Public Correspondence, Duplex No Yes TELEPHONE
47CH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG28B RX Only 162.000 Public Correspondence, RX Only ------ ------ TELEPHONE60 156.025 160.625 Public Correspondence, Duplex No Yes TELEPHONE61A 4156.075 156.075 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED62A 156.125 156.125 Canadian Coast Guard Yes Yes CANADIAN CG64 156.225 160.825 Public Correspondence, Duplex No Yes TELEPHONE64A 4156.225 156.225 U.S. Government, Canadian Commercial FishingYes Yes UNAUTHORIZED65A 156.275 156.275 Port Operations Yes Yes PORT OPS66A 1156.325 156.325 Port Operations – 1W Only Yes Yes PORT OPS67 156.375 156.375 Commercial, SAR Yes No COMMERCIAL68 156.425 156.425 Boat Operations, Recreational Yes No SHIP - SHIP69 156.475 156.475 Commercial Fishing Only Yes Yes COMMERCIAL70 6156.525 156.525 Digital Selective Calling - DSC ------ ------ DSC71 156.575 156.575 Boat Operations, Recreational Yes Yes PLEASURE72 156.625 156.625 Intership Yes No SHIP - SHIP73 156.675 156.675 Commercial Fishing Only Yes Yes COMMERCIAL74 156.725 156.725 Commercial Fishing Only Yes Yes COMMERCIAL77 1156.875 156.875 Port Operations –1W Only Yes Yes PORT OPS78A 156.925 156.925 Boat Operations, Recreational Yes No SHIP - SHIP79A 156.975 156.975 Commercial Yes Yes COMMERCIAL80A 157.025 157.025 Commercial Yes Yes COMMERCIAL81A 4157.075 157.075 U.S. Government Operations Yes Yes UNAUTHORIZED82A 4157.125 157.125 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED83 157.175 161.775 Canadian Coast Guard Yes Yes CANADIAN CG83A 4157.175 157.175 U.S. Government, Canadian Coast GuardYes Yes UNAUTHORIZED83B RX Only 161.775 Canadian Coast Guard, RX Only ------ ------ CANADIAN CG84 157.225 161.825 Public Correspondence, Marine OperatorNo Yes TELEPHONE85 157.275 161.875 Public Correspondence, Marine OperatorNo Yes TELEPHONE86 157.325 161.925 Public Correspondence, Marine OperatorNo Yes TELEPHONE87 157.375 161.975 Public Correspondence, Marine OperatorNo Yes TELEPHONE88 157.425 162.025 Public Correspondence, Marine OperatorNo Yes TELEPHONE
48WEATHER MHz TRAFFIC TYPE NAME TAGWx01 RX Only 162.550 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx02 RX Only 162.400 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx03 RX Only 162.475 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx04 RX Only 162.425 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx05 RX Only 162.450 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx06 RX Only 162.500 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx07 RX Only 162.525 NOAA WEATHER CHANNEL ------ ------ NOAA WXWx08 RX Only 161.650 CANADIAN WEATHER CHANNEL ------ ------ CANADA WXWx09 RX Only 161.775 CANADIAN WEATHER CHANNEL ------ ------ CANADA WXWx10 RX Only 163.275 NOAA WEATHER CHANNEL ------ ------ NOAA WXSPECIAL NOTES ON CANADA CHANNEL USAGE1. LOW POWER (1W) only.2. Receive Only.3. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.4. Lightly Shaded Simplex channels 21A, 23A, 61A, 64A, 81A, 82A, and 83A cannot be lawfully used in Canada waters unless special authorization is obtained from the Canadian Coast Guard. Not for use by the general public.5. The letter “A” illuminated by the channel number indicates the Canada channel is simplex. This same channel is always duplex when selecting International. There is no “A” reference for International channels. The letter “B” is only used for some Canadian “Receive Only” channels.6. Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.7. The CANADA mode is not legal to use in U.S. waters.
49C.4 EC CHANNEL CHARTCH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG01 156.050 160.650 Public Correspondence, Duplex No Yes TELEPHONE02 156.100 160.700 Public Correspondence, Duplex No Yes TELEPHONE03 156.150 160.750 Public Correspondence, Duplex No Yes TELEPHONE04 156.200 160.800 Port Operations, Duplex No Yes PORT OPS05 156.250 160.850 Port Operations, VTS in Selected AreasNo Yes PORT OPS/VTS06 156.300 156.300 Inter-ship Safety Yes No SAFETY07 156.350 160.950 Port Operations, Duplex No Yes PORT OPS08 156.400 156.400 Commercial (inter-ship only) Yes No COMMERCIAL09 156.450 156.450 Recreational Calling Channel Yes Yes CALLING10 156.500 156.500 Commercial Yes Yes COMMERCIAL11 156.550 156.550 Commercial, VTS in Selected AreasYes Yes VTS12 156.600 156.600 Port Operations, Selected VTS AreasYes Yes PORT OPS/VTS13 2156.650 156.650 Intership Navigation Safety (bridge-to-bridge), 1W with Power-upYes No BRIDGE COM14 156.700 156.700 Port Operations, VTS in Selected AreasYes Yes PORT OPS/VTS15 1156.750 156.750 Port Operations – 1W Only Yes Yes PORT OPS16 156.800 156.800 International Distress, Safety, and CallingYes Yes DISTRESS17 1156.850 156.850 State Controlled – 1W Only Yes Yes SAR18 156.900 161.500 Port Operations, Duplex No Yes PORT OPS19 156.950 161.550 Commercial, Duplex No Yes SHIP - SHORE20 157.000 161.600 Port Operations, Duplex No Yes PORT OPS21 157.050 161.650 Port Operations, Duplex No Yes PORT OPS22 157.100 161.700 Port Operations, Duplex No Yes PORT OPS23 157.150 161.750 Public Correspondence, Duplex No Yes TELEPHONE24 157.200 161.800 Public Correspondence, Duplex No Yes TELEPHONE25 157.250 161.850 Public Correspondence, Duplex No Yes TELEPHONE26 157.300 161.900 Public Correspondence, Duplex No Yes TELEPHONE27 157.350 161.950 Public Correspondence, Duplex No Yes TELEPHONE28 157.400 162.000 Public Correspondence, Duplex No Yes TELEPHONE
5060 156.025 160.625 Public Correspondence, Duplex No Yes TELEPHONE61 156.075 160.675 Port Operations, Duplex No Yes PORT OPS62 156.125 160.725 Port Operations, Duplex No Yes PORT OPS63 156.175 160.775 Port Operations, Duplex No Yes PORT OPS64 156.225 160.825 Public Correspondence, Duplex No Yes TELEPHONE65 156.275 160.875 Port Operations, Duplex No Yes PORT OPS66 156.325 160.925 Port Operations, Duplex No Yes PORT OPS67 156.375 156.375 Commercial, bridge-to-bridge Yes No BRIDGE COM68 156.425 156.425 Boat Operations, Recreational Yes No SHIP - SHIP69 156.475 156.475 Port Operations Yes Yes PORT OPS70 3156.525 156.525 Digital Selective Calling - DSC ------ ------ DSC71 156.575 156.575 Port Operations Yes Yes PORT OPS72 156.625 156.625 Intership Yes No SHIP - SHIP73 156.675 156.675 Port Operations Yes Yes PORT OPS74 156.725 156.725 Port Operations Yes Yes PORT OPS77 156.875 156.875 Intership Yes No SHIP - SHIP78 156.925 161.525 Non-Commercial, Duplex No Yes SHIP - SHORE79 156.975 161.575 Commercial, Duplex No Yes SHIP - SHORE80 157.025 161.625 Commercial, Duplex No Yes SHIP - SHORE81 157.075 161.675 Port Operations, Duplex No Yes PORT OPS82 157.125 161.725 Port Operations, Duplex No Yes PORT OPS83 157.175 161.775 Public Correspondence, Duplex No Yes TELEPHONE84 157.225 161.825 Public Correspondence, Duplex No Yes TELEPHONE85 157.275 161.875 Public Correspondence, Duplex No Yes TELEPHONE86 157.325 161.925 Public Correspondence, Duplex No Yes TELEPHONE87 161.975 161.975 AIS - do not use for public correspondence reallocated------ ------ AIS188 162.025 162.025 AIS - do not use for public correspondence reallocated------ ------ AIS2CH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG
51SPECIAL CHANNELS 7CH SEND(MHz)RECEIVE(MHz)TRAFFIC TYPE SHIP TOSHIPSHIP TO SHORENAME TAG00 6156.000 156.000 UK Coast Guard Users Yes Yes UK COAST GRDM 157.425 157.850 UK Marina Channel M Yes Yes UK MARINAM2 161.425 161.425 UK Marina Channel M2 Yes Yes UK MARINA31 157.550 162.150 INT’L, Duplex (Holland) No Yes NL MARINA96H 162.425 162.425 INT’L (Belgium) No Yes BEL G MARINAL1 155.500 155.500 INT’L (Scandinavia) Yes no LEISURE 1L2 155.525 155.525 INT’L (Scandinavia) Yes no LEISURE 2L3 155.650 155.650 INT’L (Scandinavia – not in Denmark)Yes no LE ISURE3F1 155.625 155.625 INT’L (Scandinavia) Yes no FISHING 1F2 155.775 155.775 INT’L (Scandinavia) Yes no FISHING 2F3 155.825 155.825 INT’L (Scandinavia) call back Yes no FISHING 3AIS1 161.975 161.975 AIS1 ----- ----- -----AIS2 162.025 162.025 AIS2 ----- ----- -----SPECIAL NOTES ON EUROPEAN INTERNATIONAL CHANNEL USAGE1. LOW POWER (1W) only.2. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.3. Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.4. The INTERNATIONAL mode is not legal for use in U.S.A. or Canada waters.5. No WX channels are available.6. Lightly Shaded Simplex channel CH00 is only available in the UK to Coast Guard users with written authorization.7. The special channels above maybe fitted to your radio. These are only licensed for use in the country indicated. No attempt should be made to use them in any other country.
52Appendix D - MMSID & License InformationVHF 7100 onlyYou must obtain a user MMSID (Marine Mobile Service Identity) and enter it into your VHF 7100 in order to use the DSC functions. Contact the appropriate authorities in your country. If you are unsure who to contact, consult your NAVMAN dealer.The user MMSID is a unique nine digit number, similiar to a personal telephone number. It is used on marine transceivers that are capable of using DSC (Digital Select Calling).Depending upon your location, you may need need a radio station license for the VHF 7100. You may also also need an individual operator’s license. NAVMAN NZ recommends that you check the requirements of your national radio communications authorities before operating DSC functions.
53Declaration of ConformityTBS
540560

Navigation menu