Navico Auckland VHF7100US VHF MARINE RADIO User Manual USERS MANUAL

Navico Auckland Limited VHF MARINE RADIO USERS MANUAL

Contents

USERS MANUAL

Download: Navico Auckland VHF7100US VHF MARINE RADIO User Manual USERS MANUAL
Mirror Download [FCC.gov]Navico Auckland VHF7100US VHF MARINE RADIO User Manual USERS MANUAL
Document ID394473
Application IDjxxs3j5Ro5kY00KN6WMnig==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize129.23kB (1615350 bits)
Date Submitted2004-02-05 00:00:00
Date Available2004-02-05 00:00:00
Creation Date2003-11-28 10:26:19
Producing SoftwareAdobe PDF Library 5.0
Document Lastmod2003-11-28 10:43:27
Document TitleUSERS MANUAL
Document CreatorAdobe InDesign 2.0.1

NAVMAN VHF 7000 / VHF 7100
Owner’s Manual
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
a reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try and correct the interference by one or more of the following
measures:
•reorient or relocate the receiving antenna.
•increase the separation between the equipment and receiver.
•connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•consult the dealer or an experienced radio/TV technician for help.
IMPORTANT:
1. Some features described in this manual are not available on every
model. In particular, DSC functions are NOT available on the NAVMAN
VHF 7000.
2. The radio channels installed into the NAVMAN VHF radio may vary
from country to country, depending upon the NAVMAN VHF radio model
and government or national communications authority regulations.
3. NAVMAN NZ Ltd recommends that you check the radio operating
licensing requirements of your country before using the NAVMAN VHF
radio. The operator is solely responsible for observing proper radio
installation and usage practices.
4. A warning label is supplied with this NAVMAN VHF radio. To comply
with FCC regulations, this label must be affixed in a location that is
clearly visible from the operating controls of this NAVMAN VHF radio.
Make sure that the chosen location is clean and dry before applying this
label.
It is the owner’s sole responsibility to install and use the instrument in such a manner
that will not cause accidents, personal injury or property damage.
NAVMAN NZ LIMITED disclaims all liability for any use of this product in a way that
may cause acidents, damage or that may violate the law.
Governing Language: This statement, any instruction manuals, user guides and other
information relating to the product (Documentation) may be translated to, or has been
translated from, another language (Translation). In the event of any conflict between any
Translation of Documentation, the English language version of the Documentation will
be the official version of the Documentation.
This manual represents the NAVMAN VHF 7000 and NAVMAN VHF 7100 at the time
of printing. NAVMAN NZ LIMITED reserves the right to make changes to specifications
without notice.
Copyright © NAVMAN NZ Limited, New Zealand. All rights reserved. NAVMAN is a
registered trademark of NAVMAN NZ Limited.
Contents
Chapter 1 - General Information
1.1
1.2
1.3
1.4
1.5
1.6
2.1
FEATURES
CUSTOMIZING YOUR NAVMAN VHF RADIO
HOW TO DISPLAY AND NAVIGATE MENUS
HOW TO ENTER ALPHANUMERIC DATA
LCD SYMBOLS AND MEANINGS
BASIC OPERATION AND KEY FUNCTIONS
RADIO MENU OPTIONS (MENU)
Chapter 2 - The Radio Menu (MENU)
2.2 MAINTAIN YOUR BUDDY LIST (BUDDY LIST)
2.2.1 Add an Entry
2.2.2 Edit an Entry
2.2.3 Delete an Entry
2.3 LOCAL OR DISTANCE SENSITIVITY (LOCAL/DST)
2.3.1 Set Distance Sensitivity
2.3.2 Set Local Sensitivity
2.4 BACKLIGHTING (BACKLIGHT) AND CONTRAST (CONTRAST)
2.4.1 Set the Backlighting Level
2.4.2 Set the Contrast Level
2.5 GPS DATA AND TIME (GPS/DATA)
2.5.1 MANUALLY ENTER Position & UTC TIME (MANUAL)
2.5.2 LOCAL Time DISPLAY (TIME OFFSET)
2.5.4 TIME DISPLAY OPTIONS (TIME DISPLAY)
2.5.6 Course & speed display options (COG/SOG)
2.5.7 GPS Alarm OPTIONS (ALARM)
2.6 GPS SIMULATOR (SIMULATOR)
2.7 RESET TO FACTORY DEFAULTS (RESET)
11
11
12
12
12
13
13
13
13
14
14
14
14
14
15
16
16
17
17
18
Chapter 3 - Radio Setup Menu (RADIO SETUP) 19
3.1
3.2
3.3
3.4
3.5
3.6
3.7
RADIO SETUP MENU (RADIO SETUP)
CUSTOMIZE OR DELETE CHANNEL NAMES (CH NAME)
RING & BEEP VOLUME (RING VOLUME) & (BEEP VOLUME)
INTERNAL SPEAKER CONNECTIONS (INTERNAL SPK)
SET THE PRIORITY CHANNEL (WATCH MODE)
WEATHER ALERT (WX ALERT)
NMEA PROTOCOL (COMM PORT)
Chapter 4 - DSC Setup Menu (DSC SETUP)
4.1 DSC SETUP - MENU OPTIONS
19
19
20
20
21
21
22
23
23
4.3 MAINTAIN YOUR GROUPS (GROUP SETUP)
4.3.1 Create a Group (GROUP SETUP)
4.3.2 EDIT GROUP NAME DETAILS (EDIT)
4.3.3 Delete a Group
4.4 RESPONSE TO INDIVIDUAL CALLS (INDIV REPLY)
4.5 ATIS MMSID AND ATIS FUNCTIONALITY (ATIS FUNC)
4.5.1 Enter or Edit the ATIS MMSID
4.5.2 Enable ATIS Functionality (ATIS FUNC)
4.7 RESPONSE TYPE TO LL CALLS (LL REPLY)
24
24
24
25
25
25
25
26
26
Chapter 5 - Sending and Receiving DSC Calls 27
5.1 WHAT IS DSC?
5.2 SENDING DSC CALLS
5.2.1 Make a Routine Call MANUALLY (INDIV REPLY)
5.2.2 Retrying a Routine Call
5.2.3 ACKNOWLEDGE AN INDIVIDUAL CALL (INDIV ACK)
5.2.4 Recall the Most Recent INCOMING Call (LAST)
5.2.5 Call a Group (GROUP)
5.2.6 Call All Ships (ALL SHIPS)
5.2.7 CALL Using the Call Log (CALL LOG)
5.2.8 CALL using the distress log (DISTRES LOG)
5.3 RECEIVING DSC CALLS
5.3.1 Receiving an All ships call (ALL SHIPS)
5.3.2 receiving an individual call (INDIVIDUAL)
5.3.3 receiving A Group call (GROUP CALL)
Chapter 6 - Distress Calls
6.1 SENDING A DISTRESS CALL
6.2 RECEIVING A DISTRESS CALL (DISTRESS!)
6.3 DISTRESS ACKNOWLEDGEMENT OR RELAY (DISTRESS ACK)
Appendix A - Technical Specifications
Appendix B - Troubleshooting
Appendix C - VHF Marine Channel Charts
C.1
C.2
C.3
C.4
INTERNATIONAL CHANNEL CHART
USA CHANNEL CHART
CANADA CHANNEL CHART
EC CHANNEL CHART
Appendix D - MMSID & License Information
27
27
28
28
29
29
29
30
30
31
32
32
32
33
34
34
35
35
36
39
40
40
43
46
49
52
Chapter 1 - General Information
1.1 FEATURES
Congratulations on your purchase of a NAVMAN VHF 7000, 7100 USA, or 7100
EC marine band VHF radio. All of these models provide the following useful
features:
•prominent channel display
•adjustable contrast settings for the LCD
•adjustable keypad backlighting for easy night-time use
•waterproof and submersible to comply with JIS-7
•GPS latitude and longitude display (when connected to a GPS)
•choice of High or Low (25 W or 1W) transmission power
•top centred PTT button for comfortable left- or right-handed use
•powerful 4W external audio output
•access to all currently-available marine VHF channel banks (USA,
Canada, International) including weather channels where available
•special CH16 or CH16/9 key for quick access to the priority
(international distress) channel
•special 3CH key to select your three favourite channels
•PSCAN (similar to dual watch) facility
In addition, the VHF 7100 models also provide:
•DSC (Digital Select Calling) capability that meets USCG SC101 and
Class D Standards. 7100 USA only.
•DSC (Digital Select Calling) capability that meets EC Class D Standards.
7100 EC only.
•DISTRESS call button to automatically transmit the MMSID and position
until an acknowledgement is received
•easy access to a buddy list of up to 20 favourite people
•MMSID storage for three favourite groups
•Group Call and All Ships Call facility
•LL position polling details
•Weather alert facility. 7100 USA only.
•ATIS facility for inland waterways. 7100 EC only.
1.2 CUSTOMIZING YOUR NAVMAN VHF RADIO
You can customize the NAVMAN VHF radio to suit your individual preferences.
Some preferences can be set directly through the keys as explained in this
chapter.
Other preferences are set up through the built-in menus and these are
explained in the other chapters.
1.3 HOW TO DISPLAY AND NAVIGATE MENUS
1. Hold down MENU (or CALL MENU). Note that only four menu items can be
displayed at any one time on the LCD.
2. Press + CH - to scroll up and down the menu until the cursor is postioned at
the desired option. Press ENT to display that option.
3. Make any entries or changes as explained in the following section.
4. Press ENT to confirm changes. Otherwise, press ESC to keep the original
entry.
5. Press ESC to exit from the screen. Any changes are active as soon as you
exit the screen.
1.4 HOW TO ENTER ALPHANUMERIC DATA
If your NAVMAN VHF radio does not have the optional alphanumeric
microphone, use the + CH - key to enter alphanumeric data.
Press + to count through numbers, or hold down to scroll rapidly to the desired
number.
Press - to step through the alphabet, or hold down to scroll rapidly to the
desired character.
1.5 LCD SYMBOLS AND MEANINGS
This simulation shows the locations of all the following information symbols:
Symbol
Meaning
TX
Transmitting.
HI LO
Transmission power. High (HI) 25W or Low (LO) 1W.
WX
Weather channel.
WX ALT
Weather Alert. Alarm beeps will sound. 7100 USA only.
BUSY
Receiver busy with an incoming signal.
PRI
Priority channel is selected.
Duplex operation. Otherwise, blank for Simplex operation.
LOCAL
Local calling is selected. Otherwise, blank for distance calling.
DSC
DSC capability is available. 7100 USA and 7100 EC only.
Incoming DSC call.
Low Battery warning.
88
Channel selected.
USA INT CAN Selected channel bank for VHF radio operations and
regulations.
Channel is temporarily deleted from the ALL SCAN operation.
B A
Channel suffix, if applicable.
CH1 CH2 CH3 Shows which of the 3 favourite channels, if any, are selected.
Otherwise blank.
ATIS
Enabled for use in inland waterways. Otherwise blank. 7100
EC only.
A typical operational display is shown here.
The latitude and longitude of the vessel and the time are shown.
Local calling is selected.
A transmission on Channel 16 is being made at high power using the
International channel bank.
Channel 16 is set as the Priority channel. It is also set as favourite channel 1.
There is an incoming DSC call so the receiver is busy.
1.6 BASIC OPERATION AND KEY FUNCTIONS
All possible keys and their functions are listed. Note that some of the keys
are not available depending on your NAVMAN VHF radio model.
Key
Function
VOL/PWR
Volume and Power. Turn clockwise to power on. Continue to
turn until a comfortable volume is reached. VOL/PWR will also
adjust the settings of an external speaker, if connected.
SQL
Squelch and Threshold Level. Sets the threshold level for the
minimum receiver signal. Turn fully counterclockwise until
random noise is heard, then turn slowly clockwise until the
random noise disappears. Make another 1/4 turn clockwise for
best reception in open sea conditions.
In areas of high noise (eg close to large cities) reception
may improve if sensitivity is reduced. Either turn SQL slowly
clockwise or use the LOCAL setting. See section 2.4.
16/9
Priority Channel. 7100 USA only. Also on the microphone.
Press to cancel all other modes and to tune into the priority
channel. Press again to return to your original channel.
The default is Channel 16. To make Channel 09 the priority
channel, hold down 16/9 until a beep sounds and 09 is
displayed.
16
Priority Channel. 7100 EC and 7000 only. Also on the
microphone. Press to cancel all other modes and to tune into
the priority channel, Channel 16, on high power. Press again to
return to your original channel.
WX
Weather Channel. 7100 USA and 7000 only. In USA and
Canadian waters, press to hear the most recently selected
weather station. The WX symbol is displayed on the LCD.
Press + or - to change to a different weather channel.
Press WX, then 16/9, then CALL MENU to leave the weather
channels and return to the most recent channel.
If a weather alert is broadcast when you are in SCAN mode, it is
picked up automatically and the alarm sounds. Press any key to
hear the weather alert.
H/L
Transmission Power. High (HI) 25W or Low (LO) 1W. Press to
toggle between high or low transmission power for the entire
channel bank. The HI or LO selection is shown on the LCD.
Some channels allow only low power transmissions. Error beeps
will sound if the power transmission setting is incorrect. Press
H/L to change it.
Some channels allow only low power transmissions intially,
but can be changed to high power by holding down H/L and
PTT at the same time. See Appendix C for a complete listing of
channel charts.
3CH
Three Favourite Channels. Also on the microphone. Press to
toggle between your favourite channels. The CH1, CH2, or CH3
symbol appears on the LCD to show which favourite channel is
selected.
To add a favourite channel for the first time, select that channel
then hold 3CH to store it in the CH1 location. Repeat the
procedure to store two more favourite channels in the CH2 and
CH3 locations respectively.
If you try and add another favourite channel it will overwrite the
existing CH3. CH1 and CH2 remain unless you delete them.
To delete a favourite channel, select that channel then hold
down 3CH until the CH1, CH2 or CH3 symbol disppears off the
LCD.
UIC
Channel Bank. 7100 USA only. Press to toggle between USA,
International or Canadian channel banks. The selected channel
bank is displayed on the LCD. All the channel charts are shown
in Appendix C.
U/I
Channel Bank. 7000 only. Press to toggle between channel
banks. Note that the channel banks available are dependent
upon your VHF radio model. The selected channel bank is
displayed on the LCD. All the channel charts are shown in
Appendix C.
DIM
Backlighting. 7100 EC only. Press to toggle between the
backlighting settings. OFF will extinguish all the backlighting
except for the DISTRESS key. (Otherwise, use the menu to
change the backlight setting.)
SCAN
Scan. Press to scan between your current channel and the
priority channel in Dual Watch mode. The weather channel is
also scanned if the USA channel bank is selected.
Hold down SCAN to enter ALL SCAN mode where the priority
channel is checked every 1.5 seconds.
When a signal is received, scanning stops at that channel and
BUSY appears on the LCD. If the signal ceases for more than 5
seconds, the scan restarts.
Press ENT to skip over (lock out) a busy channel when in ALL
SCAN mode and resume the scan. An X is shown on the LCD to
designate a skipped channel. Note that it is not possible to skip
over the priority channel.
Press SCAN to stop at the current channel.
+ CH -
Channel Select. Also on the microphone. The current channel
is shown on the LCD with any suffix (such as A or B) in small
letters below the channel number.
Press + or - to step through the available channels one at a
time, or hold down to scroll rapidly through all the available
channels. See Appendix C for a complete listing of channel
charts.
Alphanumeric Entry. This key can also be used for menu
selection and for alphanumeric entry. Press + or - to scroll the
cursor up or down menu options when navigating menus.
To enter numbers, press + to count through the numbers or
hold down to scroll rapidly to the desired number.
To enter a character, press - to step through the alphabet or
hold down to scroll rapidly to the desired character.
ENT
Enter. Use ENT when navigating menus, to confirm entries and
edits.
ESC
Escape. Use ESC when navigating menus, to clear incorrect
entries, to exit from a menu without saving changes, and to
back up to the previous screen.
CALL/MENU
DSC Setup Menu and DSC Call Menu. 7100 USA and 7100 EC
only. Press to enter the DSC Call Menu and make DSC calls. See
Chapter 5.
Hold down to enter the DCS Setup Menu and customize your
NAVMAN VHF radio. See Chapter 4.
MENU
Radio menu. 7000 only. Press to enter the Radio Menu and
customize your NAVMAN VHF radio. See Chapter 3.
DISTRESS
Send a DSC Distress Call. 7100 USA & 7100 EC only. See
Chapter 6.
PTT
Press To Talk. Press PTT to transmit at any time. This
automatically exits you from menu mode. You must release
PTT to receive a signal.
If PTT sticks, a built-in timer will automatically shut down a
transmission after five minutes and sound the error beeps.
If you have a USA 7100, note that PTT will not operate if you are
in WX mode.
10
Chapter 2 - The Radio Menu (MENU)
2.1 RADIO MENU OPTIONS (MENU)
The following options are available through MENU (or CALL MENU):
BUDDY LIST
Maintain your buddy list.
See Section 2.2.
LOCAL/DIST
Set radio sensitivity.
See Section 2.3.
BACKLIGHT
Set backlight level.
See Section 2.4.
CONTRAST
Set contrast level.
See Section 2.4.
GPS/DATA
MANUAL
SETTING
DSC SETUP
USER MMSID
GROUP SETUP
INDIV REPLY
ATIS MMSID
ATIS FUNC
DSC FUNC
LL REPLY
RADIO SETUP
CH NAME
RING VOLUME
INTERNAL SPK
WATCH MODE
WX ALERT
COM PORT
Set position & UTC manually.
See Section 2.5.
Set local time and time format.
See Section 2.5.
DSC Setup Menu.
7100 USA and EC models only.
See Chapter 4.
Make DSC calls.
7100 USA and EC models only.
See Chapter 5.
Radio Setup Menu.
See Chapter 3.
GPS SIMULATOR
Turn the GPS Simulator on/off.
See Section 2.6.
RESET
Reset factory settings.
See Section 2.7.
Sections 1.3 and 1.4 explain how to navigate around the menu and enter, save
and change data.
11
2.2 MAINTAIN YOUR BUDDY LIST (BUDDY LIST)
7100 USA and EC models only.
Use the Buddy List to store the names and associated
MMSIDs of 20 favourite people in alphanumeric order.
The following sections show to use BUDDY LIST to add,
edit, and delete entries on your buddy list.
Chapter 3 explains how to call a buddy.
2.2.1 ADD AN ENTRY
1. Select BUDDY LIST.
2. Press ENT again to display the list of entries. Scroll down (if required) to the
first available blank line and press ENT.
3. Enter the buddy name (this may be alphanumeric) then press > twice to go
to the MMSID entry line.
4. Enter the MMSID associated with that buddy name. This must be numeric.
5. Select SAVE & EXIT then press ENT to store the new entry, or CANCEL to exit
without saving the new entry.
The BUDDY LIST will arrange itself automatically into alphabetic order.
Note that when the BUDDY LIST is full (20 entries), you cannot make a new
entry until you have deleted an existing entry.
2.2.2 EDIT AN ENTRY
1. Select BUDDY LIST.
2. Press ENT again to display the list of entries. Scroll down (if required) to the
incorrect entry.
3. Select EDIT.
4. Edit the buddy name or press ENT to edit only the MMSID.
5. Press ENT when you are finished.
6. Choose STORE to store the changes, or EXIT to exit without saving the
changes. The BUDDY LIST is displayed again.
12
7. If more changes are required, repeat Steps 2 thru 6. Otherwise, press ESC to
exit.
2.2.3 DELETE AN ENTRY
1. Select BUDDY LIST.
2. Press ENT again to display the list of entries. Scroll down to entry that you
want to delete.
3. Select DELETE.
4. A confirmation question (ARE YOU SURE?) is displayed. Select YES to delete
the entry and return to the list of entries, or NO to keep the entry.
Any deletions are effective immediately.
2.3 LOCAL OR DISTANCE SENSITIVITY (LOCAL/DST)
Use LOCAL/DIST to improve the sensitivity of the receiver
either locally (LOCAL) or over distances (DST).
LOCAL is not recommended for use in open sea conditions.
It is designed for use in areas of high radio noise, such as
close to cities.
See also Squelch Control (SQL) in Section 1.3.
2.3.1 SET DISTANCE SENSITIVITY
1. Select LOCAL/DST.
2. Select DISTANT
sensitivity.
and
select
it
to
disable
local
LOCAL disappears off the LCD.
2.3.2 SET LOCAL SENSITIVITY
1. Select LOCAL/DST.
2. Scroll to LOCAL and select it to switch on local
sensitivity.
LOCAL is displayed on the LCD as a reminder that local
sensitivity is selected.
13
2.4 BACKLIGHTING (BACKLIGHT) AND CONTRAST (CONTRAST)
Use BACKLIGHT to set the backlight levels for the LCD, the
keypad, and the microphone at the same intensity.
Use CONTRAST to set the contrast level for the LCD.
2.4.1 SET THE BACKLIGHTING LEVEL
1. Select BACKLIGHT.
2. Select the appropriate backlight level, or off (OFF).
Changes are effective when you exit from the screen.
Note that the DISTRESS key backlighting cannot be
switched off, even if OFF is selected.
2.4.2 SET THE CONTRAST LEVEL
1. Select CONTRAST.
2. Select the apropriate contrast level. Changes are
effective when you exit from the screen.
2.5 GPS DATA AND TIME (GPS/DATA)
If the boat has an operational GPS navigation receiver, the
VHF radio automatically detects and updates the vessel
position and the local time.
However, if the GPS navigation receiver is disconnected or
absent, you can specify the vessel position and the local
time manually, using the GPS/DATA option.
This information is important because it will be used if a DSC distress call is
transmitted.
2.5.1 MANUALLY ENTER POSITION & UTC TIME (MANUAL)
1. Select GPS/DATA, then MANUAL. Note that this function is available only if
an operational GPS receiver is not connected.
2. Enter the latitude, then the longitude, then the UTC.
14
3. Press ENT when all the information is correct.
The vessel latitude and longitude are shown on the LCD, with the UTC time.
The prefix M indicates a manual entry.
2.5.2 LOCAL TIME DISPLAY (TIME OFFSET)
The local time can be set by entering the time offset between UTC and local
time as follows.
1. Select GPS/DATA, then SETTING.
2. Select TIME OFFSET to enter the difference between UTC and local time.
Half hour increments can be used with a maximum offset of +13.5 and a
minimum offset of -13.5.
In this example, a difference of +1.5 hours has been entered and the local
time is displayed with the suffix LOC.
INSERT WORLD PICTURE SHOWING TIME ZONES OFFSET FROM UTC/GMT.
2.5.3 POSITION DISPLAY OPTIONS (LL DISPLAY)
If you have entered the vessel position manually as described in the previous
section, the vessel position is always shown on the LCD with the suffix M.
However, if the time is being updated through a GPS navigation receiver, you
can switch the vessel position display on the LCD on or off as follows:
15
1. Select GPS/DATA, then SETTING.
2. Select LL DISPLAY.
2. Select ON (on) or OFF (off) as desired. In this example, OFF has been
selected and so the LCD no longer shows the vessel position.
2.5.4 TIME DISPLAY OPTIONS (TIME DISPLAY)
If you have entered the time manually as described in the previous sections,
the time is always shown on the LCD with the prefix M.
However, if the vessel position is being updated through a GPS navigation
receiver, you can switch the time display on the LCD on or off as follows:
1. Select GPS/DATA, then SETTING.
2. Select TIME DISPLAY.
2. Select ON (on) or OFF (off) as desired. In this example, OFF has been
selected and so the LCD no longer shows the time.
If the time display is set ON, course and speed data are not displayed on the
LCD (see section 2.6.6).
2.5.5 TIME FORMAT OPTIONS (TIME FORMAT)
Time can be shown in 12 or 24 hour format.
1. Select GPS/DATA, then SETTING.
2. Select TIME FORMAT.
2. Select 12 Hr or 24 Hr as desired. In this example, 12 hour format has been
selected and so the LCD shows the am or pm suffix.
2.5.6 COURSE & SPEED DISPLAY OPTIONS (COG/SOG)
Use this option to display course over ground (COG) and speed over ground
16
(SOG) data on the LCD.
1. Select GPS/DATA, then SETTING.
2. Select COG/SOG.
2. Select ON (on) or OFF (off) as desired. In this example, ON has been selected
and so the LCD shows the bearing and speed.
If GOG/SOG is set ON, the time is not displayed on the LCD (see section
2.6.4).
2.5.7 GPS ALARM OPTIONS (ALARM)
7100 USA and 7100 EC only.
The GPS Alarm is usually set to ON so that if the GPS navigation receiver is
disconnected, the alarm sounds.
1. Select GPS/DATA, then SETTING.
2. Select ALARM.
2. Select ON (on) or OFF (off) as desired.
2.6 GPS SIMULATOR (SIMULATOR)
The GPS Simulator is usually set to OFF. However, if you want to test it, turn it
on. (new pictures)
1. Select SIMULATOR, then select ON (on) or OFF (off) as desired.
17
If the GPS Simulator is turned on, the simulated speed, bearing, and LL
positions appear on the LCD as:
7100 EC
11 knots moving 045º
50º 30.000N,
00º 00.000E
7100 USA
11 knots moving 045º
25º 00.000N
82º 00.000W
This data is updated automatically during the simulation.
Note that it is not possible to send a transmission when in simulator mode.
2.7 RESET TO FACTORY DEFAULTS (RESET)
Use this to return every setting to the factory defaults except your user MMSID
and the entries in your buddy list. (new picture)
1. Select RESET, then select YES.
18
Chapter 3 - Radio Setup Menu (RADIO SETUP)
3.1 RADIO SETUP MENU (RADIO SETUP)
CH NAME
Customize channel names.
See Section 3.2.
RING VOLUME
Set the volume level of the incoming call notification
beeps. See section 3.3.
BEEP VOLUME
Set the volume level of the beeps.
See section 3.3.
INTERNAL SPK
Switch on or off any internal speakers that are connected
to the VHF radio. See section 3.4.
WATCH MODE
Edit the channel name or use the default name.
See section 3.5.
WX ALERT
Switch the weather alert beeps on or off. (7100 USA only.)
See section 3.6.
COM PORT
Select NMEA protocol for communications between the
VHF radio and any other instruments. See section 3.7.
Sections 1.3 and 1.4 explain how to navigate around the menu and enter, save
and change data.
3.2 CUSTOMIZE OR DELETE CHANNEL NAMES (CH NAME)
The channel charts are listed in Appendix C with their default name tags. CH
NAME gives you the option to edit the channel name tags displayed on your
LCD, as follows:
1. Select RADIO SETUP, then select CH NAME.
2. Use + or - to step through the channels with their name tags until you see
the channel name tag you want to change. In this example, there is no
channel name tag associated with CH01.
3. Select EDIT and press ENT to edit the existing name tag. Input the new name
along the dashed line, then press ENT.
19
4. Select YES to confirm the new channel name tag.
Delete a channel name as follows:
1. Select RADIO SETUP, then select CH NAME.
2. Use + or - to step through the channels with their name tags until you see
the channel name tag you want to change. In this example, the PHONETALK
name tag associated with CH02 is deleted.
3. Select DELETE and press ENT.
4. Select YES to confirm the deletion. The channel is shown with no name tag.
3.3 RING & BEEP VOLUME (RING VOLUME) & (BEEP VOLUME)
Set the volume level of the incoming signal beeps (RING VOLUME) and/or
the error and warning beeps (BEEP VOLUME) to HIGH (high) or LOW (low) as
follows:
1. Select RADIO SETUP, then select RING VOLUME or BEEP VOLUME as
appropriate.
2. Select HIGH or LOW. (The beeps will sound at the new level.)
3.4 INTERNAL SPEAKER CONNECTIONS (INTERNAL SPK)
If any internal speakers are connected to the VHF radio, use this menu option
to switch them on or off to suit your cabin arrangements.
20
1. Select RADIO SETUP, then select INTERNAL SPK.
2. Select ON or OFF.
3.5 SET THE PRIORITY CHANNEL (WATCH MODE)
If you have a VHF 7000 or a VHF 7100 EC, watch mode is similiar to a dual
watch, scanning between the priority channel and the working channel. CH16
is the priority channel.
However, only if you have the 7100 USA model and are operating in USA or
Canadian waters, you can set the priority channel to cover both CH16 and
CH09 as well as the working channel, as follows:
1. Select RADIO SETUP, then select WATCH MODE.
2. Select CH16 + CH09 for three channel scanning.
3.6 WEATHER ALERT (WX ALERT)
7100 USA only.
The NOAA provides several weather forecast channels for USA and Canadian
waters. If severe weather such as storms or hurricanes are forecast, the NOAA
broadcasts a weather alert. You can pick up these weather alerts, as follows:
1. Select RADIO SETUP, then select Wx ALERT.
2. Select ON. When a weather alert is broadcast, the alarm beeps will sound. (If
21
3.7 NMEA PROTOCOL (COMM PORT)
The VHF radio can be added to a group of instruments using NMEA protocol.
1. Select RADIO SETUP, then select COM PORT.
2. Select NMEA. Specify whether CHECKSUM is on (ON) or off (OFF). CHECKSUM
ON is the usual standard.
22
Chapter 4 - DSC Setup Menu (DSC SETUP)
These DSC facilities are available only on the VHF7100
USA and VHF7100 EC models, and a valid user MMSID
must be entered to access the DSC functions.
4.1 DSC SETUP - MENU OPTIONS
The following options are available:
USER MMSID
Enter your user MMSID. If you do not have a user MMSID,
see Appendix E.) See section 4.2.
GROUP SETUP
Enter or change the name and/or details of a group.
See section 4.3.
INDIV REPLY
Choose an automatic or manual response to calls.
See section 4.4.
ATIS MMSID
Enter or change your ATIS MMSID (7100 EC only).
See section 4.5.
ATIS FUNC
Enable/disable the ATIS function (7100 EC only).
See section 4.5.
DSC FUNC
Turn DSC scanning on/off.
See section 4.6.
LL REPLY
Select the type of response to an LL request.
See section 4.7.
Sections 1.3 and 1.4 explain how to navigate around the menu and enter, save
and change data.
4.2 ENTER YOUR USER MMSID (USER MMSID)
This is a once-only operation. You must enter your user MMSID before you can
access the DSC functions, as follows:
23
You can display and read your user MMSID at any time, but you get only one
opportunity to enter your user MMSID.
1. Select DSC SETUP, then USER MMSID.
2. If this is the first time that you are entering your user MMSID, a dashed line
appears.
Enter your user MMSID along the dashed line and press ENT when it is
correct.
3. Input the user MMSID again as a check, then select STORE.
If the user MMSID has been entered correctly both times, it is displayed for
3 seconds on the LCD and then saved (SAVED).
4.3 MAINTAIN YOUR GROUPS (GROUP SETUP)
Use GROUP SETUP to create, edit, or delete 1, 2, or 3 groups of frequently
called people stored in alphanumeric order.
A group MMSID always starts with 0.
4.3.1 CREATE A GROUP (GROUP SETUP)
1. Select DSC SETUP, then select GROUP SETUP.
2. If this is the first time that you are entering a group name, a dashed line
appears. Otherwise, any existing group names are displayed. Scroll down
(if required) and enter the group name along the dashed line. It can be
alphanumeric.
3. Enter the group MMSID. (Note that the first number is always 0.)
4. The group name and group MMSID are shown in a confirmation screen.
Select STORE if the entry is correct.
4.3.2 EDIT GROUP NAME DETAILS (EDIT)
1. Select DSC SETUP, then select GROUP SETUP.
24
2. Select the group, then select EDIT.
3. Make the changes to the group name and/or to the group MMSID.
4. Select STORE to store the changes.
4.3.3 DELETE A GROUP
1. Select DSC SETUP, then select GROUP SETUP.
2. Select the group, then select DELETE OK.
3. Press ENT to confirm the deletion.
4.4 RESPONSE TO INDIVIDUAL CALLS (INDIV REPLY)
You can respond to incoming individual calls with an automatic response or
with a manual response.
An automatic response sends an acknowledgement and then sets the request
link channel, ready for a conversation.
A manual response asks if you want to acknowlege the call, and then asks if
you want to converse with the caller.
1. Select DSC SETUP, then select
INDIV REPLY.
2. Select AUTO for an automatic
response, or MANUAL for a
manual response.
4.5 ATIS MMSID AND ATIS FUNCTIONALITY (ATIS FUNC)
7100 EC only. You must enter your ATIS MMSID to access ATIS functionality if
you are navigating inland waterways within Europe.
4.5.1 ENTER OR EDIT THE ATIS MMSID
To enter or edit your ATIS MMSID:
1. Select DSC SETUP, then ATIS MMSID.
25
2. If this is the first time that you are entering your ATIS MMSID, a dashed line
appears. Enter your ATIS MMSID here and select STORE. The first number is
always 9.
If you are editing an existing ATIS MMSID, this will be displayed. Make the
required changes.
3. Input the ATIS MMSID again as a check. Press ENT and select SAVED.
If the user MMSID has been entered correctly both times, it is displayed for
3 seconds on screen and then stored.
4.5.2 ENABLE ATIS FUNCTIONALITY (ATIS FUNC)
7100 EC only. ATIS functionality will operate only after the ATIS MMSID has
been entered (see previous section).
1. Select DSC SETUP, then ATIS
FUNC.
2. Select ON to enable the ATIS
functionality and automatically
disable DSC functionality.
A warning message will appear:
WARNING DSC OFF.
(Note that it is not possible to have both ATIS ON and DSC ON simultaneously.
When you enable one, the transceiver will automatically disable the other and
display a warning message.)
4.6 DSC FUNCTIONALITY OPTIONS (DSC FUNC)
DSC functionality can be disabled but this is not recommended.
1. Select DSC
SCAN.
SETUP,
then
DSC
2. Select ON to operate the
DSC functionality. (This will
automatically
disable
ATIS
functionality on the 7100 EC and
a warning message will appear:
WARNING ATIS OFF.)
(Note that it is not possible to have both ATIS ON and DSC ON simultaneously
on the 7100 EC. When you enable one, the transceiver will automatically
disable the other and display a warning message.)
4.7 RESPONSE TYPE TO LL CALLS (LL REPLY)
You can set up the VHF 7100 to respond to an LL request in one of four ways.
AUTO - automatically reply to any incoming LL request.
AUTO BUDDY - automatically reply to any incoming call
from anyone in your buddy list or a group list.
MANUAL - choose whether to reply or not.
OFF - switch off notification of any incoming LL requests.
26
Chapter 5 - Sending and Receiving DSC Calls
These DSC facilities are available only on the
VHF7100 USA and VHF7100 EC models, and a valid
user MMSID must have been entered to access the
5.1 WHAT IS DSC?
DSC (Digital Selective Calling) is a semi-automated method of establishing VHF,
MF, and HF radio calls. It has been designated as an international standard by
the IMO (International Maritime Organization) and is part of the GMDSS (Global
Maritime Distress and Safety System).
Currently, you are required to monitor Distress Channel 16, but DSC will
eventually replace listening watches on distress frequencies and will be used
to broadcast routine and urgent maritime safety information.
DSC enables you to send and receive calls from any vessel or coast station that
is equipped with DSC functionality, and within geographic range. Calls can be
categorised as distress, urgency, safety, or routine, and DSC selects a working
channel automatically.
5.2 SENDING DSC CALLS
1. Press CALL MENU to show the types of DSC call that can
be made.
Note that only four DSC call types can be shown at any
one time on the LCD menu.
2. Press + or - to scroll up and down the DSC call types
until the cursor is postioned at the desired option.
Then press ENT. The DSC call types are:
INDIVIDUAL
Make a manual call or reply to a new caller or a buddy.
See Section 5.2.1 and 5.2.2.
INDIV ACK
See Section 5.2.3 TBS
LAST
Show the details of the most recent incoming call.
See Section 5.2.4.
GROUP
Make a call to one of your three groups.
See Section 5.2.5.
ALL SHIPS
Make an urgent, safety, or routine call to all ships USA??
See Section 5.2.6.
CALL LOG
Show the details of the 20 most recent incoming calls.
See Section 5.2.7.
DISTRESS LOG
Show the details of the 20 most recent distress calls.
See Section 5.2.8.
27
5.2.1 MAKE A ROUTINE CALL MANUALLY (INDIV REPLY)
If you chose to respond manually to individual calls when you set up your
DSC options (see Section 3.5), you must enter the caller’s MMSID or select the
buddy name, and then specify the calling channel.
1. When the incoming call is complete, press CALL MENU to enter DSC mode,
then select INDIVIDUAL.
2. If the caller is not in your buddy list, select MANUAL MMSID and then enter
the MMSID of the caller along the dashed line.
If the caller is in your buddy list, just scroll down the list of buddies and
select that buddy.
3. Now specify the calling channel using the + and - key and monitor that
channel briefly to ensure that it is clear before you transmit. (This is an FCC
requirement.) If it is busy, select a different calling channel.
NOTE: If the call is from a coast station, the VHF 7100 will recognise this
and automatically specify a channel.
4. The VHF 7100 summarises the call data and asks if it should send the call
(SEND?). Press ENT to send the call and CALLING appears on the LCD.
5. If the call is acknowledged (ACKNOWLEDGED), press to talk when invited
(PRESS PTT TO TALK).
6. If there is no reply (UNABLE TO ACKNOWLEDGE), retry the call (see Section
5.2.2).
5.2.2 RETRYING A ROUTINE CALL
28
1. If there is no reply to your call after one minute (UNABLE TO ACKNOWLEDGE)
the VHF 7100 asks if you want to retry the call (SEND AGAIN?).
2. Select YES and press ENT to retry the call.
The VHF 7100 will repeat this cycle twice. If the call still cannot be placed,
the VHF 7100 returns to normal operation.
5.2.3 ACKNOWLEDGE AN INDIVIDUAL CALL (INDIV ACK)
TBS. OR is this VHF 7200 specific?
5.2.4 RECALL THE MOST RECENT INCOMING CALL (LAST)
The VHF 7100 stores the contact details of your most recent incoming call, so
that you can call up quickly, if necessary.
1. Press CALL MENU to enter DSC mode, then select LAST CALL.
The VHF 7100 displays the contact details of the most recent incoming
call.
2. Press ENT to send a call to that contact, then set the channel and continue
as explained in Section 5.2.1.
5.2.5 CALL A GROUP (GROUP)
1. Press CALL MENU to enter DSC mode, then select GROUP CALL. The VHF
7100 displays the names of your groups.
2. Select the group that you want to call, then set the channel and continue as
explained in Section 5.2.1.
29
5.2.6 CALL ALL SHIPS (ALL SHIPS)
1. Press CALL MENU to enter DSC mode, then select ALL SHIPS.
2. The priority is set automatically to URGENT. However, if you have a VHF
7100 USA, you can select one of the following call priorities:
URGENT - for use when a serious situation or problem arises that could lead
to a distress situation
SAFETY - to send safety information to all other vessels in range;
ROUTINE - routine call.
3. The VHF 7100 asks for confirmation of the all ships call. Select YES and press
ENT to transmit the call. Continue as explained in Section 5.2.1.
5.2.7 CALL USING THE CALL LOG (CALL LOG)
The Call Log contains the contact details for the 20 most recent incoming calls,
so that you call any of them again quickly.
1. Press CALL MENU to enter DSC mode, then select CALL LOG.
Scroll down to the desired contact details.
The VHF 7100 displays the contact details for the most recent incoming call
as the first entry (01) in the call log. In the example, the contact details for
the 11th most recent call are displayed.
2. Set the channel and continue as explained in Section 5.2.1.
30
5.2.8 CALL USING THE DISTRESS LOG (DISTRES LOG)
The Distress Log contains the contact details for the 10 most recently received
distress calls, so that you can call any of them quickly. Always try to make voice
contact on CH16 first, as follows:
1. Press CALL MENU to enter DSC mode, then select DISTRES LOG.
2. Scroll down to the distress call entry that you want to call.
The VHF 7100 displays the details for the most recently received distress
call as the first entry (01) in the distress log.
The details are displayed over two screens that alternate every 1.5 seconds;
the first screen shows the user MMSID and location, and the second screen
shows the user MMSID and the nature and time of the emergency (if
specified).
3. Set the channel and continue as explained in Section 5.2.1.
31
5.3 RECEIVING DSC CALLS
Five types of DSC calls can be received from vessels within range at various
priority levels:
DISTRESS - see Chapter 5.
ALL SHIPS - Urgency, or Safety priority (see Section 5.3.1)
INDIVIDUAL - Urgency, Safety, or Routine priority (see Section 5.3.2)
GROUP - Routine priority only (see Section 5.3.3)
In addition to the audible alert, the telephone icon will flash on the LCD.
5.3.1 RECEIVING AN ALL SHIPS CALL (ALL SHIPS)
1. When you receive notification of an ALL SHIPS call, press
any key to cancel the alert. The VHF 7100 automatically
selects CH16.
The priority level and the user MMSID are displayed on
the LCD. If the VHF 7100 recognises the user MMSID as
one of your buddies, the buddy’s name is displayed in
place of the user MMSID.
2. You do not need to send an acknowledgement. If necessary, press PTT to
initiate voice contact on CH16 and then switch to a working channel.
The call data is stored in the Call Log (see Section 5.2.7).
5.3.2 RECEIVING AN INDIVIDUAL CALL (INDIVIDUAL)
1. When you receive notification of an INDIVIDUAL call,
press any key to cancel the alert. The VHF 7100
automatically selects the channel designated in the
incoming call.
In the example, an individual routine call has selected
CH72. However, safety and urgency priority level calls
always select CH16.
The priority level and the user MMSID are displayed on the LCD. If the VHF
7100 recognises the user MMSID as one of your buddies, the buddy’s name
is displayed in place of the user MMSID.
2. The VHF 7100 prompts you to press ENT to acknowledge the incoming call
(PRESS ENTER TO ACK BACK!).
3. Press ENT, then the caller should respond to your acknowledgement by
making voice contact on the designated channel. If this does not happen,
you can press PTT to initiate voice contact instead.
The call data is stored in the Call Log (see Section 5.2.7).
32
5.3.3 RECEIVING A GROUP CALL (GROUP CALL)
1. When you receive notification of a GROUP call, press
any key to cancel the alert. The VHF 7100 automatically
selects the channel designated in the incoming call.
The priority level is always routine, and the group is
identified on the LCD. The group will be one of the
three groups of frequently called people that you set
up earlier (see Section 3.4).
2. You do not need to send an acknowledgement. If desired, press PTT to
initiate voice contact on the designated channel.
The call data is stored in the Call Log (see Section 5.2.7).
33
Chapter 6 - Distress Calls
This DSC facility is available only on the VHF7100 USA
and VHF7100 EC models, and a valid user MMSID must
have been entered to access this DSC function.
6.1 SENDING A DISTRESS CALL
1. Open the red cover labelled DISTRESS.
If time is available to specify the nature of the distress, go to step 2.
Otherwise, go directly to step 3.
2. Press the DISTRESS key to display the following categories. Scroll to the
category that describes your situation, then press ENT:
UNDEFINED
FIRE
FLOODING
COLLISION
GROUNDING
LISTING
SINKING
ADRIFT
ABANDONING
PIRACY
MAN IN WATER
EPRIB
3. Hold down the DISTRESS key for about 3 seconds, until you see the distress
call sent message (DISTRES CALL SENT!) on the LCD. The whole display
starts to flash and beep.
The distress call repeats five times continuously. It then repeats randomly
every 3.5 to 4.5 minutes until a distress acknowledgement (DISTRESS ACK)
is received from a search and rescue authority or until you cancel the
distress call manually.
The VHF 7100 selects CH16 automatically so that you can hear any incoming
voice contacts from search and rescue authorities or other vessels within
range.
Press ESC if you need to cancel the distress call. This is the only key that
operates in distress mode.
34
6.2 RECEIVING A DISTRESS CALL (DISTRESS!)
An alert sounds when a distress call (DISTRESS!) is received. The VHF 7100
automatically selects CH16 and displays the details of the distress call on the
LCD.
The details are displayed over two screens that alternate every 1.5 seconds; the
first screen shows the user MMSID and location (if specified), and the second
screen shows the user MMSID and the nature and time of the emergency (if
specified).
If the location and time are not specified, these are replaced with sequences of
9s and 8s respectively. In this example, the location has not been specified.
1. Press any key to cancel the alert. You do not need to send an
acknowledgement.
2. Press PTT to establish voice contact.
6.3 DISTRESS ACKNOWLEDGEMENT OR RELAY (DISTRESS ACK)
An alert sounds when a distress acknowledgement or relay (DISTRESS ACK) is
received. The VHF 7100 automatically selects CH16 and displays the details of
the distress call on the LCD.
The details are displayed over two screens that alternate every 1.5 seconds; the
first screen shows the user MMSID and location (if specified), and the second
screen shows the user MMSID and the nature and time of the emergency (if
specified).
If the location and time are not specified, these are replaced with sequences of
9s and 8s respectively. In this example, the location has not been specified.
1. Press any key to cancel the alert. You do not need to send an
acknowledgement.
2. Maintain a listening watch on CH16 and standby to lend assistance.
35
Appendix A - Technical Specifications
NAVMAN VHF 7000
GENERAL
Power Supply:
Current drain:
Transmit
Receive
Useable channels:
Mode:
13.6V DC.
6A at 25W Tx / 1.5A at 1W Tx
Less than 250mA in standby
International, USA (country specific)
16K0G3E (FM)
PHYSICAL
LCD display (viewing): 41(H) x 53(W) mm
FSTN 4 x 12 character
Contrast and
Dimming control:
Yes
Antenna connector:
SO-239 (50 ohm)
Temperature Range: -15ºC to +50ºC
Waterproof:
JIS-7
Dimensions:
161(W) x 75(H) x 147(D) mm - without bracket
Weight:
1.29kg (2.8lbs) - without microphone
Frequency stability:
+/- 10ppm
Frequency control:
PLL
GPS/NMEA input:
Yes
Comm. port:
4800 baud NMEA
DSC:
No
FEATURES
Flush Mount kit and
dust cover:
Local/Distant control:
Position polling:
Track-your-buddy:
Call logs:
DSC (USCG SC101
and Class D):
Channel Naming:
Tri watch, Favourite
channel scan, All scan:
User programmable
MMSID:
MMSID and NAME
directory:
Yes
Yes
No
No
No
No
Yes
Yes
No
No
TRANSMITTER
Frequency:
156.025 - 157.425MHz
Output power:
25W / 1W selectable
Transmitter protection: Open / short circuit of antenna
36
Max Freq deviation:
+/- 5kHz
Spurious & harmonics: 80dB@25W, 60dB@1W
Modulation distortion: Less than 4%@ 1kHz for a +/-3kHz deviation
RECEIVER
Frequency:
156.025 - 163.275MHz
12dB SINAD sensitivity: 0.25uV (distant) / 2.5uV (local)
20db SINAD sensitivity:0.35uV
Adjacent CH selectivity:more than 70dB
Spurious response:
more than 70db
Intermodulation
Rejection ratio:
more than 68dB
Residual Noise level: more than -40dB unsquelched
Audio output power: 2W (with 8 ohm at 10% distortion)
4W with 4 ohm external speaker
Compass safe distance: 0.Xm TBS
Specifications are subject to change without notice.
NAVMAN VHF 7100
GENERAL
Power Supply:
Current drain:
Transmit
Receive
Useable channels:
Mode:
13.6V DC.
6A at 25W Tx / 1.5A at 1W Tx
Less than 250mA in standby
International, USA, Canada, Weather (country specific)
16K0G3E (FM) / 16K0G2B (DSC)
PHYSICAL
LCD display (viewing): 41(H) x 53(W) mm
FSTN 4 x 12 character
Contrast and
Dimming control:
Yes
Antenna connector:
SO-239 (50 ohm)
Temperature Range: -15ºC to +50ºC
Waterproof:
JIS-7
Dimensions:
161(W) x 75(H) x 147(D) mm - without bracket
Weight:
1.29kg (2.8lbs) - without microphone
Frequency stability:
+/- 10ppm
Frequency control:
PLL
GPS/NMEA input:
Yes
Comm. port:
4800 baud NMEA
DSC:
Yes
FEATURES
Flush Mount kit and
dust cover:
Yes
Local/Distant control: Yes
Position polling:
Yes
37
Track-your-buddy:
Call logs:
DSC (USCG SC101
and Class D):
Channel Naming:
Tri watch, Favourite
channel scan, All scan:
User programmable
MMSID:
MMSID and NAME
directory:
No
Yes - 20 individual and 20 distress
Yes (7100 USA)
Yes
Yes
Yes
Yes - 20 numbers & group
TRANSMITTER
Frequency:
156.025 - 157.425MHz
Output power:
25W / 1W selectable
Transmitter protection: Open / short circuit of antenna
Max Freq deviation:
+/- 5kHz
Spurious & harmonics: better than 2.5µW
Modulation distortion: Less than 4%@ 1kHz for a +/-3kHz deviation
RECEIVER
Frequency:
156.025 - 163.275MHz
12dB SINAD sensitivity: 0.25uV (distant) / 2.5uV (local)
20db SINAD sensitivity:0.35uV
Adjacent CH selectivity:more than 65dB
Spurious response:
more than 65db
Intermodulation
Rejection ratio:
more than 65dB
Residual Noise level: more than -40dB unsquelched
Audio output power: 2W (with 8 ohm at 10% distortion)
4W with 4 ohm external speaker
Compass safe distance: 0.Xm TBS
Specifications are subject to change without notice.
38
Appendix B - Troubleshooting
1. The transceiver will not power up.
A fuse may have blown OR there is no voltage getting to the transceiver.
a) Check the power cable for cuts, breaks, or squashed sections.
b) Replace the fuse (2 spare fuses are supplied).
c) Check the battery voltage. This must be greater than 10.5V.
2. The transceiver blows the fuse when the power is switched on.
The power wires may have been reversed.
a) Check that the red wire is connected to the positive battery terminal, and
the black wire is connected to the negative battery terminal.
3. The speaker makes popping or whining noises when the engine is
running.
Electrical noise may be interfering with the transceiver.
a) Re-route the power cables away from the engine.
b) Add a noise suppressor to the power cable.
c) Use resistive spark plug wires and/or use an alternator whine filter.
4. No sound from the external speaker.
a) Check that the external speaker cable is physically connected.
b) Check the polarity of the external speaker cable.
5. Transmissions are always on low power, even when high (HI) power is
selected.
The antenna may be faulty.
a) Test the transceiver with a different antenna.
b) Have the antenna checked out.
6. Battery symbol is displayed.
The power supply is too low or too high.
a) Check the battery voltage. This should be between 10.5V and ???
b) Check the generator.
7. No position information is displayed.
The GPS cable may faulty or the GPS setting may be incorrect.
a) Check that the GPS cable is physically connected.
b) Check the polarity of the GPS cable.
c) Check the baud rate setting of the GPS if applicable. The baud rate setting
should be 4800 and parity should be set to NONE.
39
Appendix C - VHF Marine Channel Charts
C.1 INTERNATIONAL CHANNEL CHART
CH SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
SHIP
TO
SHIP
SHIP TO NAME TAG
SHORE
01
156.050 160.650
Public Correspondence, Duplex
No
Yes
TELEPHONE
02
156.100 160.700
Public Correspondence, Duplex
No
Yes
TELEPHONE
03
156.150 160.750
Public Correspondence, Duplex
No
Yes
TELEPHONE
04
156.200 160.800
Port Operations, Duplex
No
Yes
PORT OPS
05
156.250 160.850
Port Operations, Selected VTS Areas No
Yes
PORT OPS/VTS
06
156.300 156.300
Inter-ship Safety
Yes
No
SAFETY
07
156.350 160.950
Port Operations, Duplex
No
Yes
PORT OPS
08
156.400 156.400
Commercial (inter-ship only)
Yes
No
COMMERCIAL
09
156.450 156.450
Recreational Calling Channel
Yes
Yes
CALLING
10
156.500 156.500
Commercial
Yes
Yes
COMMERCIAL
11
156.550 156.550
Commercial, VTS in Selected Areas Yes
Yes
VTS
12
156.600 156.600
Port Operations, Selected VTS Areas Yes
Yes
PORT OPS/VTS
13
156.650 156.650
Intership Navigation Safety (bridge- Yes
to-bridge)
No
BRIDGE COM
14
156.700 156.700
Port Operations, Selected VTS Areas Yes
Yes
PORT OPS/VTS
15 1 156.750 156.750
Port Operations – 1W Only
Yes
Yes
PORT OPS
16
International Distress, Safety, and
Calling
Yes
Yes
DISTRESS
17 1 156.850 156.850
State Controlled – 1W Only
Yes
Yes
SAR
18
156.900 161.500
Port Operations, Duplex
No
Yes
PORT OPS
19
156.950 161.550
Commercial, Duplex
No
Yes
SHIP - SHORE
20
157.000 161.600
Port Operations, Duplex
No
Yes
PORT OPS
21
157.050 161.650
Port Operations, Duplex
No
Yes
PORT OPS
22
157.100 161.700
Port Operations, Duplex
No
Yes
PORT OPS
23
157.150 161.750
Public Correspondence, Duplex
No
Yes
TELEPHONE
24
157.200 161.800
Public Correspondence, Duplex
No
Yes
TELEPHONE
25
157.250 161.850
Public Correspondence, Duplex
No
Yes
TELEPHONE
26
157.300 161.900
Public Correspondence, Duplex
No
Yes
TELEPHONE
27
157.350 161.950
Public Correspondence, Duplex
No
Yes
TELEPHONE
28
157.400 162.000
Public Correspondence, Duplex
No
Yes
TELEPHONE
156.800 156.800
40
CH SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
SHIP
TO
SHIP
SHIP TO NAME TAG
SHORE
60
156.025 160.625
Public Correspondence, Duplex
No
Yes
TELEPHONE
61
156.075 160.675
Port Operations, Duplex
No
Yes
PORT OPS
62
156.125 160.725
Port Operations, Duplex
No
Yes
PORT OPS
63
156.175 160.775
Port Operations, Duplex
No
Yes
PORT OPS
64
156.225 160.825
Public Correspondence, Duplex
No
Yes
TELEPHONE
65
156.275 160.875
Port Operations, Duplex
No
Yes
PORT OPS
66
156.325 160.925
Port Operations, Duplex
No
Yes
PORT OPS
67
156.375 156.375
Commercial, bridge-to-bridge
Yes
No
BRIDGE COM
68
156.425 156.425
Boat Operations, Recreational
Yes
No
SHIP - SHIP
69
156.475 156.475
Port Operations
Yes
Yes
PORT OPS
70 3 156.525 156.525
Digital Selective Calling - DSC
------
------
DSC
71
156.575 156.575
Port Operations
Yes
Yes
PORT OPS
72
156.625 156.625
Intership
Yes
No
SHIP - SHIP
73
156.675 156.675
Port Operations
Yes
Yes
PORT OPS
74
156.725 156.725
Port Operations
Yes
Yes
PORT OPS
77
156.875 156.875
Intership
Yes
No
SHIP - SHIP
78
156.925 161.525
Non-Commercial, Duplex
No
Yes
SHIP - SHORE
79
156.975 161.575
Commercial, Duplex
No
Yes
SHIP - SHORE
80
157.025 161.625
Commercial, Duplex
No
Yes
SHIP - SHORE
81
157.075 161.675
Port Operations, Duplex
No
Yes
PORT OPS
82
157.125 161.725
Port Operations, Duplex
No
Yes
PORT OPS
83
157.175 161.775
Public Correspondence, Duplex
No
Yes
TELEPHONE
84
157.225 161.825
Public Correspondence, Duplex
No
Yes
TELEPHONE
85
157.275 161.875
Public Correspondence, Duplex
No
Yes
TELEPHONE
86
157.325 161.925
Public Correspondence, Duplex
No
Yes
TELEPHONE
87
157.375 161.975
Public Correspondence, Duplex
No
Yes
TELEPHONE
88
157.425 162.025
Public Correspondence, Duplex
No
Yes
TELEPHONE
41
WEATHER
MHz
TRAFFIC TYPE
NAME TAG
Wx01
RX Only 162.550
NOAA WEATHER CHANNEL
------
------ NOAA WX
Wx02
RX Only 162.400
NOAA WEATHER CHANNEL
------
------ NOAA WX
Wx03
RX Only 162.475
NOAA WEATHER CHANNEL
------
------ NOAA WX
Wx04
RX Only 162.425
NOAA WEATHER CHANNEL
------
------ NOAA WX
Wx05
RX Only 162.450
NOAA WEATHER CHANNEL
------
------ NOAA WX
Wx06
RX Only 162.500
NOAA WEATHER CHANNEL
------
------ NOAA WX
Wx07
RX Only 162.525
NOAA WEATHER CHANNEL
------
------ NOAA WX
Wx08
RX Only 161.650
CANADIAN WEATHER CHANNEL ------
------ CANADA WX
Wx09
RX Only 161.775
CANADIAN WEATHER CHANNEL ------
------ CANADA WX
Wx10
RX Only 163.275
NOAA WEATHER CHANNEL
------ NOAA WX
------
SPECIAL NOTES ON INTERNATIONAL CHANNEL USAGE
1. LOW POWER (1W) only.
2. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key
before transmitting. Used normally in bridge-to-bridge communications.
3. Channel 70 is designated for use exclusively for Digital Selective Calling
(DSC), such as Distress, Safety, and Ship Calls. No voice communication is
allowed on CH70.
4. The INTERNATIONAL mode is not legal for use in U.S. or Canada waters.
42
C.2 USA CHANNEL CHART
CH
SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
01A
156.050 156.050
SHIP
TO
SHIP
SHIP
NAME TAG
TO
SHORE
Port Operations, Selected VTS Areas Yes
Yes
PORT OPS/VTS
03A 4 156.150 156.150
US Government, Coast Guard
Yes
Yes
UNAUTHORIZED
05A
156.250 156.250
Port Operations, Selected VTS Areas Yes
Yes
PORT OPS/VTS
06
156.300 156.300
Inter-ship Safety
Yes
No
SAFETY
07A
156.350 156.350
Commercial
Yes
Yes
COMMERCIAL
08
156.400 156.400
Commercial (inter-ship only)
Yes
No
COMMERCIAL
09
156.450 156.450
Recreational Calling Channel
Yes
Yes
CALLING
10
156.500 156.500
Commercial
Yes
Yes
COMMERCIAL
11
156.550 156.550
Commercial, VTS in Selected
Areas
Yes
Yes
VTS
12
156.600 156.600
Port Operations, Selected VTS Areas Yes
Yes
PORT OPS/VTS
13 3
156.650 156.650
Intership Navigation Safety
(bridge-to-bridge), 1W with
Power-up
No
BRIDGE COM
14
156.700 156.700
Port Operations, Selected VTS Areas Yes
Yes
PORT OPS/VTS
15 2
RX Only 156.750
Environmental, RX Only
------
ENVIROMENTAL
16
156.800 156.800
International Distress, Safety, and Yes
Calling
Yes
DISTRESS
17 1
156.850 156.850
State Controlled – 1W Only
Yes
Yes
SAR
18A
156.900 156.900
Commercial
Yes
Yes
COMMERCIAL
19A
156.950 156.950
Commercial
Yes
Yes
COMMERCIAL
20
157.000 161.600
Port Operations, Canadian Coast No
Guard, Duplex
Yes
PORT OPS
20A
157.000 157.000
Yes
------
Port Operations
Yes
Yes
PORT OPS
21A 4 157.050 157.050
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
22A
Coast Guard Liaison
Yes
Yes
COAST GUARD
23A 4 157.150 157.150
157.100 157.100
U.S. Government, Coast Guard
Yes
Yes
UNAUTHORIZED
24
157.200 161.800
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
25
157.250 161.850
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
26
157.300 161.900
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
27
157.350 161.950
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
28
157.400 162.000
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
43
CH
SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
SHIP
TO
SHIP
SHIP
NAME TAG
TO
SHORE
61A 4 156.075 156.075
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
63A
Port Operations, VTS in Selected Yes
Areas
Yes
PORT OPS/VTS
64A 4 156.225 156.225
U.S. Government, Canadian
Commercial Fishing
Yes
Yes
UNAUTHORIZED
65A
156.275 156.275
Port Operations
Yes
Yes
PORT OPS
66A
156.325 156.325
Port Operations
Yes
Yes
PORT OPS
67 3
156.375 156.375
Commercial, bridge-to-bridge, 1W Yes
with Power-up
No
BRIDGE COM
68
156.425 156.425
Boat Operations, Recreational
Yes
No
SHIP - SHIP
69
156.475 156.475
Boat Operations, Recreational
Yes
Yes
PLEASURE
70 6
156.525 156.525
Digital Selective Calling - DSC
------
------
DSC
71
156.575 156.575
Boat Operations, Recreational
Yes
Yes
PLEASURE
72
156.625 156.625
Boat Operations, Recreational
Yes
No
SHIP - SHIP
73
156.675 156.675
Port Operations
Yes
Yes
PORT OPS
74
156.725 156.725
Port Operations
Yes
Yes
PORT OPS
77 1
156.875 156.875
Port Operations –1W Only
Yes
Yes
PORT OPS
78A
156.925 156.925
Boat Operations, Recreational
Yes
No
SHIP - SHIP
79A
156.975 156.975
Commercial
Yes
Yes
COMMERCIAL
80A
157.025 157.025
Commercial
Yes
Yes
COMMERCIAL
81A 4 157.075 157.075
U.S. Government, Environmental Yes
Protection Agency Operations
Yes
UNAUTHORIZED
82A 4 157.125 157.125
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
83A 4 157.175 157.175
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
84
157.225 161.825
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
85
157.275 161.875
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
86
157.325 161.925
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
87
157.375 161.975
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
88
157.425 162.025
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
88A
157.425 157.425
Commercial, Intership Only
Yes
No
COMMERCIAL
156.175 156.175
44
WEATHER
MHz
TRAFFIC TYPE
NAME TAG
Wx01
RX Only 162.550 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx02
RX Only 162.400 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx03
RX Only 162.475 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx04
RX Only 162.425 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx05
RX Only 162.450 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx06
RX Only 162.500 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx07
RX Only 162.525 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx08
RX Only 161.650 CANADIAN WEATHER CHANNEL ------
------
CANADA WX
Wx09
RX Only 161.775 CANADIAN WEATHER CHANNEL ------
------
CANADA WX
Wx10
RX Only 163.275 NOAA WEATHER CHANNEL
------
NOAA WX
------
SPECIAL NOTES ON USA CHANNEL USAGE
1. LOW POWER (1W) only.
2. Receive Only.
3. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key
before transmitting. Used normally in bridge-to-bridge communications.
4. Lightly Shaded Simplex channels 03A, 21A, 23A, 61A, 64A, 81A, 82A, and
83A cannot be lawfully used in U.S. waters unless special authorization is
obtained from the U.S. Coast Guard. Not for use by the general public.
5. The letter “A” illuminated by the channel number indicates the USA channel
is simplex. This same channel is always duplex when selecting International.
There is no “A” reference for International channels. The letter “B” is only
used for some Canadian “Receive Only” channels.
6. Channel 70 is designated for use exclusively for Digital Selective Calling
(DSC), such as Distress, Safety, and Ship Calls. No voice communication is
allowed on CH70.
45
C.3 CANADA CHANNEL CHART
CH
SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
SHIP SHIP TO NAME TAG
TO
SHORE
SHIP
01
156.050
160.650
Public Correspondence, Duplex
No
Yes
TELEPHONE
02
156.100
160.700
Public Correspondence, Duplex
No
Yes
TELEPHONE
03
156.150
160.750
Public Correspondence, Duplex
No
Yes
TELEPHONE
04A 156.200
156.200
Canadian Coast Guard, SAR
Yes
Yes
CANADIAN CG
05A 156.250
156.250
Port Operations, VTS in Selected Yes
Areas
Yes
PORT OPS/VTS
06
156.300
156.300
Inter-ship Safety
Yes
No
SAFETY
07A 156.350
156.350
Commercial
Yes
Yes
COMMERCIAL
08
156.400
156.400
Commercial (inter-ship only)
Yes
No
COMMERCIAL
09
156.450
156.450
Recreational Calling Channel
Yes
Yes
CALLING
10
156.500
156.500
Commercial
Yes
Yes
COMMERCIAL
11
156.550
156.550
Commercial, VTS in Selected
Areas
Yes
Yes
VTS
12
156.600
156.600
Port Operations, VTS in Selected Yes
Areas
Yes
PORT OPS/VTS
13 3 156.650
156.650
Intership Navigation Safety
(bridge-to-bridge)
No
BRIDGE COM
14
156.700
156.700
Port Operations, VTS in Selected Yes
Areas
Yes
PORT OPS/VTS
15 1 156.750
156.750
Commercial – 1W Only
Yes
Yes
COMMERCIAL
16
156.800
156.800
International Distress, Safety, and Yes
Calling
Yes
DISTRESS
17 1 156.850
156.850
State Controlled – 1W Only
Yes
Yes
SAR
18A 156.900
156.900
Commercial
Yes
Yes
COMMERCIAL
19A 156.950
156.950
Canadian Coast Guard
Yes
Yes
CANADIAN CG
20 1 157.000
161.600
Canadian Coast Guard, Duplex– No
1W Only
Yes
CANADIAN CG
21
157.050
161.650
Port Operations, Duplex
No
Yes
PORT OPS
21A 157.050
157.050
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
21B RX Only 161.650
Port Operations, RX Only
------
------
PORT OPS
22A 157.100
157.100
Canadian Coast Guard Liaison
Yes
Yes
CANADIAN CG
23
157.150
161.750
Public Correspondence, Duplex
No
Yes
TELEPHONE
24
157.200
161.800
Public Correspondence, Duplex
No
Yes
TELEPHONE
25
157.250
161.850
Public Correspondence, Duplex
No
Yes
TELEPHONE
Yes
25B RX Only 161.850
Public Correspondence, RX Only ------
------
TELEPHONE
26
157.300
161.900
Public Correspondence, Duplex
No
Yes
TELEPHONE
27
157.350
161.950
Public Correspondence, Duplex
No
Yes
TELEPHONE
28
157.400
162.000
Public Correspondence, Duplex
No
Yes
TELEPHONE
46
CH
SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
28B RX Only 162.000
60
SHIP SHIP TO NAME TAG
TO
SHORE
SHIP
Public Correspondence, RX Only ------
------
TELEPHONE
156.025
160.625
Public Correspondence, Duplex
No
Yes
TELEPHONE
61A 156.075
156.075
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
62A 156.125
156.125
Canadian Coast Guard
Yes
Yes
CANADIAN CG
64
156.225
160.825
Public Correspondence, Duplex
No
Yes
TELEPHONE
64A 156.225
156.225
U.S. Government, Canadian
Commercial Fishing
Yes
Yes
UNAUTHORIZED
65A 156.275
156.275
Port Operations
Yes
Yes
PORT OPS
66A 156.325
156.325
Port Operations – 1W Only
Yes
Yes
PORT OPS
67
156.375
156.375
Commercial, SAR
Yes
No
COMMERCIAL
68
156.425
156.425
Boat Operations, Recreational
Yes
No
SHIP - SHIP
69
156.475
156.475
Commercial Fishing Only
Yes
Yes
COMMERCIAL
70 6 156.525
156.525
Digital Selective Calling - DSC
------
------
DSC
71
156.575
156.575
Boat Operations, Recreational
Yes
Yes
PLEASURE
72
156.625
156.625
Intership
Yes
No
SHIP - SHIP
73
156.675
156.675
Commercial Fishing Only
Yes
Yes
COMMERCIAL
74
156.725
156.725
Commercial Fishing Only
Yes
Yes
COMMERCIAL
77 1 156.875
156.875
Port Operations –1W Only
Yes
Yes
PORT OPS
78A 156.925
156.925
Boat Operations, Recreational
Yes
No
SHIP - SHIP
79A 156.975
156.975
Commercial
Yes
Yes
COMMERCIAL
80A 157.025
157.025
Commercial
Yes
Yes
COMMERCIAL
81A 157.075
157.075
U.S. Government Operations
Yes
Yes
UNAUTHORIZED
82A 157.125
157.125
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
83
157.175
161.775
Canadian Coast Guard
Yes
Yes
CANADIAN CG
83A 157.175
157.175
U.S. Government, Canadian
Coast Guard
Yes
Yes
UNAUTHORIZED
83B RX Only 161.775
Canadian Coast Guard, RX Only ------
------
CANADIAN CG
84
157.225
161.825
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
85
157.275
161.875
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
86
157.325
161.925
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
87
157.375
161.975
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
88
157.425
162.025
Public Correspondence, Marine
Operator
No
Yes
TELEPHONE
47
WEATHER
MHz
TRAFFIC TYPE
NAME TAG
Wx01
RX Only 162.550 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx02
RX Only 162.400 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx03
RX Only 162.475 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx04
RX Only 162.425 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx05
RX Only 162.450 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx06
RX Only 162.500 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx07
RX Only 162.525 NOAA WEATHER CHANNEL
------
------
NOAA WX
Wx08
RX Only 161.650 CANADIAN WEATHER CHANNEL ------
------
CANADA WX
Wx09
RX Only 161.775 CANADIAN WEATHER CHANNEL ------
------
CANADA WX
Wx10
RX Only 163.275 NOAA WEATHER CHANNEL
------
NOAA WX
------
SPECIAL NOTES ON CANADA CHANNEL USAGE
1. LOW POWER (1W) only.
2. Receive Only.
3. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key
before transmitting. Used normally in bridge-to-bridge communications.
4. Lightly Shaded Simplex channels 21A, 23A, 61A, 64A, 81A, 82A, and 83A
cannot be lawfully used in Canada waters unless special authorization
is obtained from the Canadian Coast Guard. Not for use by the general
public.
5. The letter “A” illuminated by the channel number indicates the Canada
channel is simplex. This same channel is always duplex when selecting
International. There is no “A” reference for International channels. The letter
“B” is only used for some Canadian “Receive Only” channels.
6. Channel 70 is designated for use exclusively for Digital Selective Calling
(DSC), such as Distress, Safety, and Ship Calls. No voice communication is
allowed on CH70.
7. The CANADA mode is not legal to use in U.S. waters.
48
C.4 EC CHANNEL CHART
CH
SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
SHIP
TO
SHIP
01
156.050
160.650
Public Correspondence, Duplex No
Yes
TELEPHONE
02
156.100
160.700
Public Correspondence, Duplex No
Yes
TELEPHONE
03
156.150
160.750
Public Correspondence, Duplex No
Yes
TELEPHONE
04
156.200
160.800
Port Operations, Duplex
No
Yes
PORT OPS
05
156.250
160.850
Port Operations, VTS in
Selected Areas
No
Yes
PORT OPS/VTS
06
156.300
156.300
Inter-ship Safety
Yes
No
SAFETY
07
156.350
160.950
Port Operations, Duplex
No
Yes
PORT OPS
08
156.400
156.400
Commercial (inter-ship only)
Yes
No
COMMERCIAL
09
156.450
156.450
Recreational Calling Channel
Yes
Yes
CALLING
10
156.500
156.500
Commercial
Yes
Yes
COMMERCIAL
11
156.550
156.550
Commercial, VTS in Selected
Areas
Yes
Yes
VTS
12
156.600
156.600
Port Operations, Selected VTS Yes
Areas
Yes
PORT OPS/VTS
13 2 156.650
156.650
Intership Navigation Safety
(bridge-to-bridge), 1W with
Power-up
Yes
No
BRIDGE COM
14
156.700
156.700
Port Operations, VTS in
Selected Areas
Yes
Yes
PORT OPS/VTS
15 1 156.750
156.750
Port Operations – 1W Only
Yes
Yes
PORT OPS
16
156.800
156.800
International Distress, Safety,
and Calling
Yes
Yes
DISTRESS
17 1 156.850
156.850
State Controlled – 1W Only
Yes
Yes
SAR
18
156.900
161.500
Port Operations, Duplex
No
Yes
PORT OPS
19
156.950
161.550
Commercial, Duplex
No
Yes
SHIP - SHORE
20
157.000
161.600
Port Operations, Duplex
No
Yes
PORT OPS
21
157.050
161.650
Port Operations, Duplex
No
Yes
PORT OPS
22
157.100
161.700
Port Operations, Duplex
No
Yes
PORT OPS
23
157.150
161.750
Public Correspondence, Duplex No
Yes
TELEPHONE
24
157.200
161.800
Public Correspondence, Duplex No
Yes
TELEPHONE
25
157.250
161.850
Public Correspondence, Duplex No
Yes
TELEPHONE
26
157.300
161.900
Public Correspondence, Duplex No
Yes
TELEPHONE
27
157.350
161.950
Public Correspondence, Duplex No
Yes
TELEPHONE
28
157.400
162.000
Public Correspondence, Duplex No
Yes
TELEPHONE
49
SHIP TO NAME TAG
SHORE
CH
SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
SHIP
TO
SHIP
60
156.025
160.625
Public Correspondence, Duplex No
Yes
TELEPHONE
61
156.075
160.675
Port Operations, Duplex
No
Yes
PORT OPS
62
156.125
160.725
Port Operations, Duplex
No
Yes
PORT OPS
63
156.175
160.775
Port Operations, Duplex
No
Yes
PORT OPS
64
156.225
160.825
Public Correspondence, Duplex No
Yes
TELEPHONE
65
156.275
160.875
Port Operations, Duplex
No
Yes
PORT OPS
66
156.325
160.925
Port Operations, Duplex
No
Yes
PORT OPS
67
156.375
156.375
Commercial, bridge-to-bridge
Yes
No
BRIDGE COM
68
156.425
156.425
Boat Operations, Recreational
Yes
No
SHIP - SHIP
69
156.475
156.475
Port Operations
Yes
Yes
PORT OPS
70 3 156.525
156.525
Digital Selective Calling - DSC
------
------
DSC
71
156.575
156.575
Port Operations
Yes
Yes
PORT OPS
72
156.625
156.625
Intership
Yes
No
SHIP - SHIP
73
156.675
156.675
Port Operations
Yes
Yes
PORT OPS
74
156.725
156.725
Port Operations
Yes
Yes
PORT OPS
77
156.875
156.875
Intership
Yes
No
SHIP - SHIP
78
156.925
161.525
Non-Commercial, Duplex
No
Yes
SHIP - SHORE
79
156.975
161.575
Commercial, Duplex
No
Yes
SHIP - SHORE
80
157.025
161.625
Commercial, Duplex
No
Yes
SHIP - SHORE
81
157.075
161.675
Port Operations, Duplex
No
Yes
PORT OPS
82
157.125
161.725
Port Operations, Duplex
No
Yes
PORT OPS
83
157.175
161.775
Public Correspondence, Duplex No
Yes
TELEPHONE
84
157.225
161.825
Public Correspondence, Duplex No
Yes
TELEPHONE
85
157.275
161.875
Public Correspondence, Duplex No
Yes
TELEPHONE
86
157.325
161.925
Public Correspondence, Duplex No
Yes
TELEPHONE
87
161.975
161.975
AIS - do not use for public
correspondence reallocated
------
------
AIS1
88
162.025
162.025
AIS - do not use for public
correspondence reallocated
------
------
AIS2
50
SHIP TO NAME TAG
SHORE
SPECIAL CHANNELS
CH
SEND
(MHz)
RECEIVE TRAFFIC TYPE
(MHz)
SHIP TO SHIP TO NAME TAG
SHIP
SHORE
00 6
156.000
156.000
UK Coast Guard Users
Yes
Yes
UK COAST GRD
157.425
157.850
UK Marina Channel M
Yes
Yes
UK MARINA
M2
161.425
161.425
UK Marina Channel M2
Yes
Yes
UK MARINA
31
157.550
162.150
INT’L, Duplex (Holland)
No
Yes
NL MARINA
96H
162.425
162.425
INT’L (Belgium)
No
Yes
BEL G MARINA
L1
155.500
155.500
INT’L (Scandinavia)
Yes
no
LEISURE 1
L2
155.525
155.525
INT’L (Scandinavia)
Yes
no
LEISURE 2
L3
155.650
155.650
INT’L (Scandinavia – not in
Denmark)
Yes
no
LE ISURE3
F1
155.625
155.625
INT’L (Scandinavia)
Yes
no
FISHING 1
F2
155.775
155.775
INT’L (Scandinavia)
Yes
no
FISHING 2
F3
155.825
155.825
INT’L (Scandinavia) call back Yes
no
FISHING 3
AIS1 161.975
161.975
AIS1
-----
-----
-----
AIS2 162.025
162.025
AIS2
-----
-----
-----
SPECIAL NOTES ON EUROPEAN INTERNATIONAL CHANNEL USAGE
1. LOW POWER (1W) only.
2. LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key
before transmitting. Used normally in bridge-to-bridge communications.
3. Channel 70 is designated for use exclusively for Digital Selective Calling
(DSC), such as Distress, Safety, and Ship Calls. No voice communication is
allowed on CH70.
4. The INTERNATIONAL mode is not legal for use in U.S.A. or Canada waters.
5. No WX channels are available.
6. Lightly Shaded Simplex channel CH00 is only available in the UK to Coast
Guard users with written authorization.
7. The special channels above maybe fitted to your radio. These are only
licensed for use in the country indicated. No attempt should be made to use
them in any other country.
51
Appendix D - MMSID & License Information
VHF 7100 only
You must obtain a user MMSID (Marine Mobile Service Identity) and enter it
into your VHF 7100 in order to use the DSC functions. Contact the appropriate
authorities in your country. If you are unsure who to contact, consult your
NAVMAN dealer.
The user MMSID is a unique nine digit number, similiar to a personal telephone
number. It is used on marine transceivers that are capable of using DSC (Digital
Select Calling).
Depending upon your location, you may need need a radio station license for
the VHF 7100. You may also also need an individual operator’s license.
NAVMAN NZ recommends that you check the requirements of your national
radio communications authorities before operating DSC functions.
52
Declaration of Conformity
TBS
53
0560
54
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2003:11:28 10:43:27+13:00
Create Date                     : 2003:11:28 10:26:19Z
Producer                        : Adobe PDF Library 5.0
Creator                         : Adobe InDesign 2.0.1
Trapped                         : False
Page Count                      : 54
Creation Date                   : 2003:11:28 10:26:19Z
Mod Date                        : 2003:11:28 10:43:27+13:00
Metadata Date                   : 2003:11:28 10:43:27+13:00
Document ID                     : adobe:docid:indd:28030443-211e-11d8-83a3-cefbd0b5fadb
Version ID                      : 1
Rendition Class                 : proof:pdf
Rendition Of Document ID        : adobe:docid:indd:28030443-211e-11d8-83a3-cefbd0b5fadb
Rendition Of Version ID         : 1
Rendition Of Rendition Class    : default
Format                          : application/pdf
Title                           : 
Tagged PDF                      : Yes
EXIF Metadata provided by EXIF.tools
FCC ID Filing: RAYVHF7100US

Navigation menu