Nedap N V LW245A Luxon Wireless LW245A User Manual 14 Installation manual Luxon Wireless CGDLW245A

Download:
Mirror Download [FCC.gov]
Document ID	2087186
Application ID	q6/gXRwfclDaB/RhaHzQyg==
Document Description	14_Installation manual Luxon Wireless CGDLW245A
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	63.31kB (791398 bits)
Date Submitted	2013-09-30 00:00:00
Date Available	2013-09-30 00:00:00
Creation Date	2013-08-11 23:30:53
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2013-08-11 23:30:53
Document Title	Microsoft Word - 14_Installation manual Luxon Wireless CGDLW245A.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	jacques.hulshof

Installation Manual
Luxon Wireless 245A
L. Hones
11 August 2013
Page 1 of 5
1. Brief product description
The Luxon Wireless 245A can be added to a fixture equipped with a Luxon e-HID
HID ballast. It facilitates
wireless communication between the electronic ballast and the Luxon Light Controller (LLC). After
installation the Luxon Wireless 245A
A becomes a RF node in the network, and data can be transferred
wirelessly to and from the light controller.
Figure 1. Installation example with Luxon Wireless HID lamps in a building with skylights
Page 2 of 5
2. Product description
Figure 2: LW245A module
Figure 3: mounting hardware
The Luxon Wireless 245A comes mounted into a protective plastic enclosure. The cable is plugged into the
module as shown in Figure 2.. This cable is used for both powering the module and the wired
communication with the ballast. Avoid disconnecting the quite fragile cable connector from the module.
The black connector is a 4 pole
le female connector with polaris
polarisation
ation and locking, for use with specific series
of Luxon e-HID ballasts. The module comes with 2 Torx T10 bolts and a protective sealing, see Fig 3.
3. Warnings
Always
lways disconnect the ballast from mains power prior to connecting the Luxon Wireless 245A.
245A
After making the connection to the Luxon ballast and powering up, the electronic circuits on the Luxon
Wireless 245A module carry life voltage. It must be made impossible to end users
ers touching the life parts.
Sufficient creepage distance must be kept towards other conductors and enclosure parts.
The enclosure is designed to comply with safety standards.
The Luxon Wireless 245A module may only be installed by qualified and trained personnel
nel.
4. Mounting instructions
The Luxon Wireless 245A module must be mounted to the outside of the luminaire,, to let the RF
transceiver have the best possible unobstructed line of sight to other Luxon Wireless nodes.
For best performance let the transceiver have a 360 degree field of sight. See also the Figure 4.
The module requires a 23mm diameter hole to pop through,, together with two 3mm holes for
f the screws
with 30mm spacing, see also Figure 5
5. The mounting area shall be flat.
The provided two self tapping screws
rews shall be used to secure the module.
The sealing can be used if IP65 ingress protection is required.
Page 3 of 5
Figure 4: Sample application
Figure 5: enclosure cut-out
out dimensions
5. Connecting
The cable is used to make a connection with the ballast. The black connector has provisions for both
polarization and locking. Please insert it carefully into the counterpart on the ballast. See also Figure 6.
Note that it might be necessary to remove a small protection cover from the ballast that is located over the
connector.
Please note that the cable to the ballast shall be kept away from the lamp output cable to minimize
electrical interference. See also Figure 7.
Figure 6: connection to ballast (example)
Figure 7: example assembly
Page 4 of 5
6. Specifications
3.3 Vdc, +/
+/- 5%
Input Supply
Max. 100mA
Operating temperature
-40
40 to +85°C
Safety
EN60950
EMC/Telecom
EN301489
EN301489-1, EN300328 V1.7.1
FCC47 part 15 and IC RSS210
Dimensions
50 X 36 mm
7. FCC and IC Declarations
FCC
CC ID: CGD
CGDLW245A and IC: 1444A-LW245A
Compliance statement
This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, includ
including
ing interference that may cause undesired operation.
Déclaration Conformité
Cet
et appareil se conforme aux normes RSS exemptés de licence du Industry Canada.
L'opération est soumis aux deuxx conditions suivantes
(1) cet appareil ne doit causer aucune interférence, et
(2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas
voulu de cet appareil.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
RF Exposure
To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or
installed at locations where there is at least 20cm separation distance between the antenna and all persons.
8.. Label artwork example for a fixture with LW245A module
Page 5 of 5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 5
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2013:08:11 23:30:53
Modify Date                     : 2013:08:11 23:30:53
Title                           : Microsoft Word - 14_Installation manual Luxon Wireless CGDLW245A.docx
Creator                         : PScript5.dll Version 5.2.2
Author                          : jacques.hulshof

EXIF Metadata provided by EXIF.tools