Nedap N V STOREIDT UHF RFID reader User Manual 14r01 9954139 QR T ID Top Version B01 CGDSTOREIDT

Download:
Mirror Download [FCC.gov]
Document ID	2006413
Application ID	FzfgA1wI2RagpOj/kjPQIw==
Document Description	14r01_9954139-QR-T-ID Top- Version B01 CGDSTOREIDT
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	130.03kB (1625348 bits)
Date Submitted	2013-07-02 00:00:00
Date Available	2013-07-03 00:00:00
Creation Date	2013-07-01 13:58:54
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2013-07-01 13:59:03
Document Title	14r01_9954139-QR-T-ID Top- Version B01 CGDSTOREIDT
Document Creator	Adobe InDesign CS6 (Windows)

!D Top
!D Top mounting template for ceiling
The !D top is most stable when the wires form a
broader basis (see picture on the right).
To make this mounting template more rigid
use the cardboard packaging of the !D top
steps for mounting !D Top on the ceiling
1. determine the position of the !D top in store
2. measure the height between !D top and ceiling
3. find the corresponding mounting holes on this
template, closest to the measured height
4. position this template to the ceiling and mark the
four mounting holes (pierce through the paper)
5. drill the holes, connect the cables and the !D top
height max. 250 cm
height max. 250 cm
height max. 200 cm
height max. 200 cm
height max. 150 cm
height max. 150 cm
height max. 100 cm
height max. 100 cm
height max. 50 cm
height max. 50 cm
height max. 25 cm
Documentation released
DESCRIPTION
APPROVED
height max. 100 cm
height max. 150 cm
height max. 200 cm
SHEET:
REV.
height max. 250 cm
1x !D Top
height max. 50 cm
A.01
part no. 9741291
drawing no. t9741-291a
N/A
height max. 25 cm
height max. 25 cm
CHCK: ?? YYYY-MM-DD
ARTICLE NUMBER
9954139
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
height max. 50 cm
ISO A
DRW: ?? YYYY-MM-DD
height max. 100 cm
N/A
DESCRIPTION
DSGN: ?? YYYY-MM-DD
DIM. IN MM
GROENLO HOLLAND
GENERAL TOLERANCES SCALE:
1:5
LIN.
ANG.
FORMAT: A3
± 0.2
± 1°
height max. 150 cm
YYYY-MM-DD
DATE
height max. 200 cm
REV.
height max. 250 cm
Ref.Nr.
ROUGHNESS ACC.
ISO 1302 in µM
10.01 OF 1
N/A
DRAWING:
4x Mounting set
3x Tie-wrap
dimensions
2x Bracket (wall mounting)
1x Poster
remove cover
65mm / 2.6”
198.5mm
198,5 / 7.8”
500mm
500/ 1.6ft
65
84.5mm
84,5/ 3.3”
height max. 25 cm
50(4x)
7(4x)
4(8x)
7(4x)
900mm
900/ 3ft
DETAIL A
SCALE 1 : 2
For hanging on
the antenna with
hook (for excample)
Weight of antenna: 4 kg
recommended - 2.0m/6.6ft
absolute max. - 2.4m/7.9ft
1m / 3ft
6,5(3x)
recommended - 3.0m/9.8ft
absolute max. - 3.5m/11.5ft
REV.
YYYY-MM-DD
DATE
Documentation released
DESCRIPTION
floor
GROENLO HOLLAND
ROUGHNESS ACC.
ISO 1302 in µM
N/A
ISO A
APPROVED
DESCRIPTION
N/A
REV.
YYYY-MM-DD
DATE
Documentation released
DESCRIPTION
REV.
A.01
10.01 OF 1
GROENLO HOLLAND
ROUGHNESS ACC.
ISO 1302 in µM
N/A
SHEET:
N/A
DRAWING:
ISO A
APPROVED
DRW: ?? YYYY-MM-DD
CHCK: ?? YYYY-MM-DD
ARTICLE NUMBER
N/A
9954139
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
recommended label free zone
DSGN: ?? YYYY-MM-DD
DIM. IN MM
GENERAL TOLERANCES SCALE:
1:5
LIN.
ANG.
FORMAT: A3
± 0.2
± 1°
DESCRIPTION
orientation in the shop
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
CHCK: ?? YYYY-MM-DD
ARTICLE NUMBER
9954139
DRW: ?? YYYY-MM-DD
1m / 3ft
required label free zone
Ref.Nr.
DSGN: ?? YYYY-MM-DD
DIM. IN MM
GENERAL TOLERANCES SCALE:
1:5
LIN.
ANG.
FORMAT: A3
± 0.2
± 1°
2m / 6ft
=150=
Ref.Nr.
2m / 6ft
50
35
196,5
2m / 6ft
distance between antennas
Holes, for excample:
- Fixing bracket at the ceiling
- Using wire rod(s)
2m / 6ft
1m / 3ft
1m / 3ft
8(4x)
265mm
265/ 10.4”
35(4x)
SHEET:
REV.
A.01
10.01 OF 1
N/A
DRAWING:
Power inserter
sales floor
stock room
all antennas
in the same
direction.
GROENLO - HOLLAND
drw: CB 2013/05/29
chk:
description:
doc. article no: 5279615
quick reference !D Top
rev. : B.01
Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system without the
prior written permission of NEDAP.
sheet: 45.01 of 1
drawing: T5279-615
drilling holes (poster recommended)
ø 0.5”
/ 3.5”
90mm
220
220mm / 8.7”
m/
mm
3m
520
520mm / 1.7ft
ceiling
(not included)
4x plugs S6 (recommended)
4x screw 4x40 (recommended)
!D Top ceiling installation
ceiling
steel-cable
01
ceiling
adjust height
press here.
not included
top-view
02
steel-cable
included
power supply
processing unit
In
Power supply 9561811. One needed for
every installed system. (not included)
Power for Reader
network IN
USB host
network OUT
USB service port
Not compatible with IEEE 802.3a* standard
Recommended to place in switch-room
Out
12
11
10
1 Yellow Heartbeat
1 2 3
1 Green
2 Blue
Blue
Processing unit at output
Blink
2 Green
Disk access
3 Green
Firmware running
buzzer
No device at output
Continuous Power inserter at output
3 Red
Power error
!D Reader
previous
next
Led Blue
01
installation of
one !D Top
Orange
Red
Firmware running Error
Green
Green
RFID active
Power
power-supply OUT
ceiling
fix cable with
tie-wrap
mounting power cable
note:
use only cat5e ethernet cable or better,
with all 8 wires connected.
unit - network IN
02
installation of
one !D Top
RJ45 connector to ethernet
outlet - customer network.
ceiling
fix cable with
tie-wrap
mounting ethernet cable
note:
use only cat5e ethernet cable or better,
with all 8 wires connected.
01
installation of
two !D Tops
note:
use only cat5e ethernet cable or better,
with all 8 wires connected.
RJ45 connector to ethernet
outlet - customer network.
ceiling
fix cable with
tie-wrap
fix cable with
tie-wrap
!D-Top - 1
!D-Top - 2
unit - network OUT
place cover
unit - network IN
connect voltage supply
230V
110V
Note :
The start up of all the
processes takes
approximately 3 minutes.
Model: !D Top Region 2
FCC ID: CGDSTOREIDT
Model: !D Top Region 2
FCC ID: CGDSTOREIDT
IC: 1444A-STOREIDT
IC: 1444A-STOREIDT
This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Cet appareil se conforme aux normes RSS 210 exemptés de license du Industry Canada.
L’opération est soumis aux deux conditions suivantes:
(1) cet appareil ne doit causer aucune interférence, et
(2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu
de cet appareil.
Les changements ou modifications n’ayant pas été expressément approuvés par la partie responsable de la conformité peuvent
faire perdre à l’utilisateur l’autorisation de faire fonctionner le matériel.
FCC and IC Radiation Exposure Statement:
This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 22 cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme a RSS-102 limites énoncées pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec une distance minimale de 22 cm entre le radiateur et votre corps.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de Classe B est conforme à la norme Canadienne ICES-003
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Tagged PDF                      : Yes
Page Count                      : 8
Create Date                     : 2013:07:01 13:58:54+02:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2013:07:01 13:59:03+02:00
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False

EXIF Metadata provided by EXIF.tools