Nedap N V VP1801 RFID system User Manual Product name
N. V. Nederlandsche Apparatenfabriek NEDAP RFID system Product name
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3114501 |
| Application ID | JJOzqcnZxEQTPUQYWePqLQ== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 56.34kB (704223 bits) |
| Date Submitted | 2016-08-28 00:00:00 |
| Date Available | 2016-08-30 00:00:00 |
| Creation Date | 2016-08-23 15:49:47 |
| Producing Software | Microsoft® Word 2013 |
| Document Lastmod | 2016-08-23 15:49:47 |
| Document Title | Product name |
| Document Creator | Microsoft® Word 2013 |
| Document Author: | Debbie van Rijswijk |
EN Quick start manual VP1801 Reader Motor Control This sheet is only intended as quick start. See service manual for detailed instructions. The VP1801 is a Velos component that is used to identify animals for feeding, weighing, milking, heat detection etc. The VP1801 is equipped with an internal switch to support a double Ethernet connection (web interface ready) and the existing VC3 interface. The Ethernet channel is used for the main functionality and communication like software updates and service. An extra communication channel is available for the VC3 systems. The function is the same as the existing Single Feeder. The VP1801 can be installed in a V-box. Doc. part. no. 5278724 / Manual version 1.0 / 08-2016 Quick start manual | VP1801 Reader Motor Control A VP1801 can be connected in different ways: To a shielded Ethernet cable and controlled by a switch or VPU: LAN next VP1801 Vin next VP1801 1. Shielded cable 2. Shielded cable, shield not connected to VP1801. Switch VPU Power + supply - When connecting the Ethernet cable, the VP1801 automatically detects TX/RX , plus and minus connections, and switches to the correct connection. To a shielded four wire cable and controlled by a VC3 host: VC3 next VP1801 SYNC next VP1801 VC3 interface bridge DR DS DR DS 1. Shielded cable 2. Shielded cable, shield not connected to VP1801. The SYNC connection is necessary for HDX ISO synchronization between other readers. For FDX a SYNC connection is possible, but not necessary if only one antenna is used. When two antennas are used the SYNC connection is always needed, even when FDX-only (no ISO) mode is enabled. The switching between the two antennas uses the ISO timing. The F SYNC connection is necessary when the distance between two antennas is ≤ 3 m. Connect the F SYNC as shown in the picture below. F SYNC I next VP1801 O5 minus next VP1801 Installation steps Ethernet Step 1 Install the VP1801 in the V-box (or other box). See the manual of the relevant equipment (feeding station, separation unit etc.) where is indicated how to install the V-box. Step 2 Connect all required wiring. See the manual of the relevant equipment and the manual of the required behaviour component. Step 3 Power up and check the LED indicators, see also the overview on page 9. Step 4 When the system is equipped with the auto-addressing function, the host computer requires the address. Select “Sp > y” in the display menu of the VP1801, see page 6. Go to Step 8. Step 5 When auto-addressing is not available, set the required address manually via “Ad” in the display menu, see page 6. Step 6 Check the ip settings via “IP” in the display menu, see page 6. Default DHCP is on. When DHCP must be switched off, set the required ip address settings via “IP” in the display menu. When DHCP is switched off, the default IP address is 192.168.1.100. Step 7 Check the antenna tuning. Select “HF > H1 > tu” in the display menu to start and enable autotune, see page 7. If external manual adjustment is used (e.g. adjustable antenna-trafo), select “AA” in the display menu, see page 7. Step 8 Test the functioning. See manual of the behaviour component. In case of malfunctioning the connected devices like sensors, motors, valves can be checked with options from menu option “It”, see page 7. Installation steps VC3 Step 1 Install the VP1801 in the V-box (or other box). See the manual of the relevant equipment (feeder, separation unit etc.) where is indicated how to install the Vbox. Step 2 Connect all required wiring. See the manual of the relevant VC3 application. Step 3 Power up and check the LED indicators, see also overview on page 9. Step 4 Set the required VC3 address via “CO > SA” in the display menu, see page 8. Step 5 Select the VC3 application and other relevant VC3 settings via “CO > AP”, see page 8. Step 5 Check the antenna tuning. Select “HF > H1 > tu” in the display menu to start and enable autotune, see page 7. If external manual adjustment is used (e.g. adjustable antenna-trafo), select “AA” in the display menu, see page 7. Step 6 Test the functioning. See the manual of the VC3 application. In case of malfunctioning of the connected devices like sensors, motors, valves execute a test with options from menu option “It”, see page 7. Doc. part. no. 5278724 / Manual version 1.0 / 08-2016 Quick start manual | VP1801 Reader Motor Control Connections See the manual of the concerning behaviour component for a detailed overview of the connections. O5 is default controlled by the identification process of the VP1801 itself, and can be overruled by the behaviour component. If the V-box has a signal light, connect it default to O5. When connecting the Ethernet cable, the VP1801 automatically detects TX/RX , plus and minus connections, and switches to the correct connection. Details VP1801 inputs and outputs LAN Vin Vout VC3 SYNC I/O 1 .. 4 O5 ANT 1 ANT 2 F SYNC Tx + Tx Rx + Rx DR DS MI Transmit (shielded CAT5E FTP (Foiled Twister Pair, also called S/UTP) stranded AWG26 or AWG24 (preferred)). Cable length max. 100 m. Transmit Receive Receive Ethernet shielding Input voltage 25 VDC, +20% -20% Minus Output (max 4A) Minus VC3 data receive. Shielded cable, cable length max. 40 m. VC3 data send Synchronisation for HDX or 2 installed antennas, AC (no plus or minus, cable must be shielded twisted pair). Max. 20 devices parallel, total cable length max. 300 m. See above Motor output or normal output max 3.5A as total current for the 4 outputs. Cable length max. 3 m. Minus for motor output or normal output Input of motor or normal input Minus for motor input or normal input Output max 400mA continue. Cable length max. 3 m. Minus for output (O) and minus input (I) Antenna 1 (core of coax). Cable length max. 10 m. Minus for antenna 1 (shield of coax) Antenna 2 (core of coax). Cable length max. 10 m. Minus for antenna 2 (shield of coax) Output for FDX synchronization of the antenna signal phase (core of coax: shield connected with minus of O5). Cable length max. 3 m. Input for synchronization of antenna signal phase (core of coax: shield connected with minus of O5). Cable length max. 3 m. Antennas The VP1801 has two antenna connections and one internal reader. When two antennas are connected, the used application determines if the second antenna is used or not. In case the reader has to control both antennas, the reader switches fast between the two antennas in a smart way. That means the identification time is divided over the two antennas with a switching time that can vary between 24ms and 120ms in case both antennas have the same priority. Priority is controlled by Ethernet control like a behaviour component. Autotune The VP1801 is equipped with the autotune function. This means it can tune an antenna by itself due to an integrated internal tuning-circuit on board. Tuning can be started with the display menu “HF > H1 > tu”, remote from an external command over Ethernet or with the web-interface of the VP1801. Important! Autotune works with all Nedap antennas. In case external antenna adjustment is used (e.g. adjustable antenna-trafo), the autotune function must be switched off to achieve the maximum reading distance. This can be done via “HF > HI > AA” in the menu display of the VP1801, see page 6. Then the autotune function is disabled until it is started again with the display menu “HF > H1 > tu”. Doc. part. no. 5278724 / Manual version 1.0 / 08-2016 Quick start manual | VP1801 Reader Motor Control Display menu 1. Display 2. Push button SERIAL NUMBER Shows last four digits of serial number SYSTEM PING Send system ping PROGRAM VERSION Shows program version DISPLAY ADDRESS Shows the actual address SET ADDRESS Change the address DISPLAY SECTION Show section (Default 0, enter 0 to have access to IP address settings) SET SECTION Change section DISPLAY VPU UNIT ADDRESS Shows actual VPU unit address ( Default 0) SET VPU UNIT ADDRESS Changes the actual unit VPU unit address SETTINGS TO DEFAULT All address settings back to factory settings DHCP IS ON Press long until blinking to turn on DHCP DHCP IS OFF Press long until blinking to turn off DHCP DISPLAY IP ADDRESS Shows actual IP address (one by one) SET IP ADDRESS DISPLAY NETWORK MASK (only shown in case of DHCP OFF) Shows network mask (8=255.0.0.0, 16=255.255.0.0, 24=255.255.255.0) SET NETWORK MASK (only shown in case of DHCP OFF) Changes network mask (8=255.0.0.0, 16=255.255.0.0, 24=255.255.255.0) SETTINGS TO DEFAULT All address settings back to factory settings AUTOTUNE MODE Starts antenna tuning ADJUST ANTENNA Antenna tuning level will be shown (sets autotuning position off) ANTENNA POWER Min/max 10 / 99. Normally set to 25 (=25% of maximum power). ANTENNA SENSITIVITY SQUELCH FDX Set squelch level FDX ANTENNA SENSITIVITY SQUELCH HDX Set squelch level HDX SIGNAL LEVEL FDX Shows signal level measured by the FDX receiver SIGNAL LEVEL HDX Shows signal level measured by the HDX receiver TEST IDENTIFICATION Shows last 2 digits of a tag number SEE H1 MENU RESPONDER NUMBER FILTER ON Accepts only 999 or 984 country code responder numbers (Nedap) RESPONDER NUMBER FILTER OFF Reads all responder numbers SETTINGS TO DEFAULT All antenna settings to default DISPLAY ERROR Safeguard error DISPLAY ERROR Output error Doc. part. no. 5278724 / Manual version 1.0 / 08-2016 Quick start manual | VP1801 Reader Motor Control DISPLAY ERROR Other system errors TEST MOTOR 1-4 M1…M4 TEST OUTPUT 1-5 L1…L5 TEST INPUT 1-4 I1…I4 VC3 DISPLAY ADDRESS Shows the actual address VC3 SET ADDRESS Change the address NO VC3 APPLICATION Select no VC3 application ETHERNET IDENTIFICATION ILS PROGRAM Select Identification Lon Standard WHS PROGRAM Select Walk through herringbone or side-by-side FSS PROGRAM Select Feed Station TAG READER SETTING FULL ISO Select Full ISO tag TAG READER FDX ONLY Select FDX only no-ISOtag 2 HOURS DATA Do not send 2 hours data over VC3 channel 2 HOURS DATA Send 2 hours data over VC3 channel VC3 COMMUNICATION SPEED 1200 BAUD Set communication speed to 1200 Baud VC3 COMMUNICATION SPEED 2400 BAUD Set communication speed to 2400 Baud VC3 COMMUNICATION SPEED 4800 BAUD Set communication speed to 4800 Baud DEFAULT Enter value 99 to return to factory defaults Press button until blinking Press button short To leave menu: press button until display is empty How to use the display and push button Activate the menu Scroll down Select Change and store Check a setting press short on the button, the display menu is shown press short press until blinking select item to change, open item by pressing till blinking, change by pressing short, store by pressing to blinking select the item to check, press until blinking, first value shown is actual setting Doc. part. no. 5278724 / Manual version 1.0 / 08-2016 Quick start manual | VP1801 Reader Motor Control LED indicators = OK = not OK POWER STATUS Display LINK/ACT V in V out COM M1…M4 I1….I4 O5 Tuning/ID One antenna Two antennas on off Green on off Slow blinking Fast blinking Short blinking Long blinking Address indicated Green on Green blinking Green on Off Red Green on off Orange blinking Red blinking Green on Green blinking Green on Off Red blinking Green on Off Green on Off Red blinking Red blinking Green on Red on Red blinking Off Green on Green blinking Red on Red/green blinking Off Power on No power Operating ok Downloading or error during download Not connected to the host Connection established to the host No communication Communication status ok Connection ok Data transmit Input power applied No power Error, plus and minus swapped Output power No power Low power Error, plus and minus swapped Connection VC3 channel Data transmit VC3 channel Output on Output off Output error Input contact closed Input contact open Output on Output off Output error Tuning Antenna tuning ok Antenna not tuned No antenna connected or low antenna signal Antenna off Antenna 1 tuning ok Antenna 1 tag identified Antenna 1 not tuned Antenna 1 tag identified + not tuned Antenna 1 off The described LED indicators apply to antenna 1 (left LED indicator). The same indicators are used for antenna 2 (right LED indicator). 10 Specifications VP 1801 Dimensions Power Software Inputs I1 – I4 Outputs O1 – O4 O5 V out Synchronization Environment IP class 143 x 120 x 68 mm LxWxH (excluding mounting rail) Weight: ± 430 gr Input voltage 25 VDC, +20% -20% Max current consumption without connected I/O = 300 mA Maximum (total) motor output current 3,5 A Protected against reverse connection power supply Check for available updates 0V – 35V DC Suitable for NPN sensors In total max. 3.5 Amp continue, short-circuiting and overload protected Max. 400mA continue, short-circuiting and overload protected Max. 4A continue, short-circuiting and overload protected Synchronization according to ISO 11785 Temperature: Operating: -10 – 50 °C, Storage: -25 – 50 °C Relative humidity: 10 – 93% non condensing Maximum noise level: 10 dBµA/m quasi peak, according CISPR 16-1-1 Conducted noise: according EN55022 IP 30. When installed in V-box IP 65 (cover and cables installed correctly !) Always use a NEDAP power supply. The Nedap guarantee-regulations are only valid when is installed as indicated in this manual. Install data cables at a safe distance from (high) powered cables. For more detailed information contact your local Nedap supplier or check the internet site. Declaration of Conformity Doc. part. no. 5278724 / Manual version 1.0 / 08-2016 11 Quick start manual | VP1801 Reader Motor Control FCC ID IC : CGDVP1801 : 1444A-VP1801 FCC and IC Compliance statement This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cet appareil se conforme aux normes RSS 210 exemptés de license du Industry Canada. L’opération est soumis aux deux conditions suivantes: (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Les changements ou modifications n’ayant pas été expressément approuvés par la partie responsable de la conformité peuvent faire perdre à l’utilisateur l’autorisation de faire fonctionner le matériel. FCC and ISED Radiation Exposure Statement This equipment complies with FCC and Canadian radiation exposure limits set forth in RSS-102 for a controlled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme a RSS-102 limites énoncées pour un environne- ment non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. ISED EMC Declaration This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de Classe B est conforme à la norme Canadienne ICES-003. FCC Information to the user Note: This equipment has been tested and found to comply with the limits for a class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequent energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determine by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To ensure compliance with FCC regulations, use only the shielded interface cables provided with the product, or additional specified components or accessories that can be used with the installation of the product. This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. © Nedap N.V., Livestock management P.O. Box 104 NL-7140 AC GROENLO The Netherlands. 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 12 Language : en-US Tagged PDF : Yes Title : Product name Author : Debbie van Rijswijk Creator : Microsoft® Word 2013 Create Date : 2016:08:23 15:49:47+02:00 Modify Date : 2016:08:23 15:49:47+02:00 Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools