Netgear orporated 10400146 PUSH2TV User Manual PTV2000 UserMan FCC

Netgear Incorporated PUSH2TV PTV2000 UserMan FCC

Users Manual

202-10591-01January 2011NETGEAR, Inc.350 East Plumeria DriveSan Jose, CA 95134Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual
iiv1.0, January 2011© 2011 by NETGEAR, Inc. All rights reserved..Technical SupportPlease refer to the support information card that shipped with your product. By registering your product athttp://www.netgear.com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades.NETGEAR, INC. Support InformationPhone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support information card.E-mail: support@netgear.comNorth American NETGEAR website: http://www.netgear.comTrademarksNETGEAR, the NETGEAR logo, ProSafe, Smart Wizard, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT and Vista are registered trademarks of Microsoft Corporation.Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of ConditionsIn the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.Certificate of the Manufacturer/ImporterIt is hereby certified that the Push 2 TV Adapter (PTV2000)/Intel Wireless Display has been suppressed in accordancewith the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations. Bestätigung des Herstellers/ImporteursEs wird hiermit bestätigt, daß dasPush 2 TV Adapter (PTV2000)/Intel Wireless Display gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.Voluntary Control Council for Interference (VCCI) StatementThis equipment is in the Class B category (information equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.
v1.0, January 2011iiiRegulatory Compliance InformationThis section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.NOTE: This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user's guide may not be available in your version of the product.Europe – EU Declaration of Conformity Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards:EN300 328, EN301 489-17, EN60950Visit the NETGEAR EU Declarations of Conformity website at:http://kb.netgear.com/app/answers/detail/a_id/11621/sno/0FCC Requirements for Operation in the United States FCC Information to UserThis product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvalsFCC Guidelines for Human ExposureThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Declaration Of ConformityWe NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the model PTV2000 Push 2 TV Adapter (PTV2000)/Intel Wireless Display complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:• This device may not cause harmful interference, and• This device must accept any interference received, including interference that may cause undesired operation.Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.
v1.0, January 2011iv• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.Canada Caution:Industry Canada regulatory information Operation is subject to the following two conditions: (1)this device maynot cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements. Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions.This device is operation in 5.15 – 5.25GHz frequency range, then restricted in indoor use only.Product and Publication DetailsModel Number: PTV2000Publication Date: January 2011Product Family: Wireless AdapterProduct Name: Push2TVHome or Business Product: HomeLanguage: EnglishPublication Part Number: 202-10591-01Publication Version Number: 1.0
vv1.0, January 2011ContentsPush 2 TV Adapter (PTV2000)/Intel Wireless Display User ManualAbout This ManualConventions, Formats, and Scope ................................................................................... ixRevision History ................................................................................................................. xChapter 1ConnectingUsing Intel Wireless Display ...........................................................................................1-1Step 1: Opening Intel Wireless Display on the Laptop .............................................1-1Step 2: Windows Firewall Security Alert ..................................................................1-2Step 3: Consenting to the License Agreement .........................................................1-2Step 4: Scanning for Adapters .................................................................................1-3Step 5: Detected Adapter .........................................................................................1-3Detected Adapters Column Information ...................................................................1-3Step 6: Connecting to the TV ...................................................................................1-4Step 7: Connected to the Adapter ............................................................................1-4Step 8: Ready to Use Intel Wireless Display ............................................................1-4First Time Connection Procedures .................................................................................1-5Changing the TV Input .............................................................................................1-5Step 1: Entering a Security Code .............................................................................1-6Step 2: Security Configuration Successful ...............................................................1-7Step 3: Adapter is Connected ..................................................................................1-7Step 4: Rename Adapter ..........................................................................................1-7Step 5: Finishing the Initial Set Up Process .............................................................1-8Initial Set Up Troubleshooting ..................................................................................1-8Disconnecting ...........................................................................................................1-8Exiting ......................................................................................................................1-9Chapter 2 TroubleshootingInitial Set Up Problems ...................................................................................................2-1
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manualviv1.0, January 2011Cords and Cables ....................................................................................................2-1On/Off Button ...........................................................................................................2-2Changing the TV Input .............................................................................................2-2Adapter Encountered a Problem on Startup ............................................................2-3There are No Adapters Detected .............................................................................2-3Security Code Issues ...............................................................................................2-3TV Image is Rough, Frozen or Delayed ...................................................................2-3Your Video Mode has Changed... ............................................................................2-4Unsupported Audio Mode ........................................................................................2-4Intel Wireless Display Requires a Different Security Profile ...........................................2-4Security Profile is Incorrect ......................................................................................2-4Manually Setting the Correct Security Profile ...........................................................2-5Your Wireless is Off .................................................................................................2-5Intel My WiFi Technology is Disabled ......................................................................2-5Unsupported Laptop Hardware ................................................................................2-5Firewall Issues .........................................................................................................2-6Windows Power Saving ...........................................................................................2-6Could Not Obtain a Network Address ......................................................................2-6Adapter Does Not Work ...........................................................................................2-6Checking the Access Point Frequency ....................................................................2-7Common Solutions to Many Issues ................................................................................2-7Known Issues .................................................................................................................2-8FAQs ..............................................................................................................................2-8How do I Change the Adapter Display Language ....................................................2-9How do I Update the Firmware? ..............................................................................2-9How do I Reset the Application Settings? ................................................................2-9How do I Reset the Adapter? ...................................................................................2-9How do I Clear the Adapter Memory? ....................................................................2-10Can I Close the Laptop Lid and Still Use Intel Wireless Display? ..........................2-10What are Adapter Properties? ................................................................................2-10Audio/Visual Tuning ...............................................................................................2-11Why does My Laptop's Color Look Different on My TV? .......................................2-11How do I Adjust the TV Display Image? .................................................................2-11How do I Adjust the Audio? ....................................................................................2-11Sample Audio Testing ............................................................................................2-11
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manualviiv1.0, January 2011Global Volume Control ...........................................................................................2-12Windows Audio Mixer .............................................................................................2-12Changing the Sound using the Windows Control Panel ........................................2-12How do I Train My Displays? .................................................................................2-12Can I play DVDs with Intel Wireless Display? ........................................................2-13How do I Contact Customer Support? ...................................................................2-13What is Auto-Connect ............................................................................................2-13Appendix A Technical SpecificationsAppendix BRelated Documents
ixv1.0, January 2011About This ManualThe NETGEAR®Push 2 TV Adapter (PTV2000)/Intel® Wireless Display User Manual describes how to install, configure and troubleshoot the Push 2 TV Adapter (PTV2000)/Intel Wireless Display. The information in this manual is intended for readers with intermediate computer and Internet skills.Conventions, Formats, and ScopeThe conventions, formats, and scope of this manual are described in the following paragraphs:•Typographical Conventions. This manual uses the following typographical conventions::Italic Emphasis, books, CDs, file and server names, extensionsBold User input, IP addresses, GUI screen textFixed Command prompt, CLI text, code italic URL links•Formats. This manual uses the following formats to highlight special messages:Warning: Ignoring this type of note may result in a malfunction or damage to the equipment.Note: This format is used to highlight information of importance or special interest.•Scope. This manual is written for the adapter according to these specifications:Product Version Push 2 TV Adapter (PTV2000)/Intel Wireless DisplayManual Publication Date January 2011
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manualxv1.0, January 2011For more information about network, Internet, firewall, and VPN technologies, see the links to the NETGEAR website in Appendix B, “Related Documents.”Note: Product updates are available on the NETGEAR, Inc. website athttp://kbserver.netgear.com/products/PTV2000.asp.Revision HistoryPart Number VersionNumber Date Description202-10591-01 1.0 October2010Original publication
1-1v1.0, January 2011Chapter 1ConnectingIntel Wireless Display allows consumers to use their HDTV as a huge, remote screen for their laptop. With Intel Wireless Display, consumers can connect their laptop to their TV and enjoy and share their personal media collections, latest YouTube videos, downloaded or streamed movies, music, or a variety of other Internet content from the comfort of their couch.Intel Wireless Display requires the following key elements:• Push 2 TV adapter. The adapter receives Wi-Fi signals from the laptop, translates the signals into an image, and sends the image to the TV.• A laptop computer with Intel Wireless Display installed. This will be used to manage the connection to the TV through the adapter. Using Intel Wireless DisplayThis section provides instructions for using Intel Wireless Display. For help with installation, see the Push 2 TV Adapter (PTV2000)/Intel® Wireless Display Installation Guide.Follow these steps to set up and use Intel Wireless Display. The side-by-side laptop and TV images shown below correspond to each step and occur at the same time. When a laptop or TV screenshot is the same for multiple steps, the image is left blank.Step 1: Opening Intel Wireless Display on the LaptopTo open Intel Wireless Display, click the Windows Start icon on the laptop’s taskbar. Type IntelWireless Display into the search field. In the search results click Intel Wireless Display. If an auto-connect adapter is set, launching the application this way will invoke a connection attempt, if the adapter is discovered. See “What is Auto-Connect” on page 2-13 for more details on auto-connect.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-2v1.0, January 2011Some laptops may have a button or key that starts Intel Wireless Display. This key will be located in different places depending on the brand of laptop. It is usually found on or around the keyboard. The key will contain a small version of the symbol below.Figure 1-1If this is the initial set up continue to Step 2. If this is the not the initial set up, it is not necessary to repeat Steps 2 and 3. Proceed to Step 4.Step 2: Windows Firewall Security AlertIn the initial set up, a firewall may block Intel Wireless Display and a firewall alert message may be displayed. If this happens, make sure to allow access for both private and public networks. For firewall help, see “Firewall Issues” on page 2-6 or see your firewall’s user manual.Step 3: Consenting to the License AgreementAfter reading and agreeing to the license agreement, click the I agree to the terms of this licensebutton and proceed to the next screen. If you do not agree to the terms of the license, click the I do not agree button. You will not be able to continue and the application will close.At this point, the TV status reads Ready for connection.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-3v1.0, January 2011Step 4: Scanning for AdaptersAfter opening Intel Wireless Display (or after agreeing to the license), the application begins scanning for available adapters and the status reads Scanning for adapters.Figure 1-2If the application does not automatically begin scanning, click the Scan for available adaptersbutton.Step 5: Detected AdapterAfter the scan is complete, any adapters in range will be displayed in the Detected adapters field. If your adapter is not detected, click the Scan for available adapters button. If your adapter still does not appear, see the “There are No Adapters Detected” on page 2-3.Detected Adapters Column InformationHeadings include: Type, Name, ID, Model, and Signal.•Type. If this is a first time connection, the circle on the TV icon will be gray. If the connection has been used previously, the icon circle will be orange.•Name. This refers to the adapter and is initially set by the adapter manufacturer. (If this is the initial set up, you can rename the adapter in a following step. In the example above the adapter has been renamed My Living Room.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-4v1.0, January 2011•ID. If the default name has not been changed, use the ID to distinguish multiple entries and find your adapter.•Model. This is the adapter manufacturer and product model name.•Signal. The number of bars represents signal strength. The scale ranges from one bar (weakest signal) to five bars (strongest signal). The bars turn from green to yellow if the signal strength falls below three bars.Step 6: Connecting to the TVTo connect the laptop to the TV, click once on the adapter and then click the Connect button. (If there are multiple adapters detected, use the ID to find the adapter.) When connecting, the laptop and TV screens both read Connecting... If the laptop status reads Connecting... and the TV screen still reads Ready for Connection, click the Cancel connect button and try connecting again. If this does not work, the connection may be blocked by a firewall. For help allowing the application through a firewall, see “Firewall Issues” on page 2-6. For additional connection help, see “Common Solutions to Many Issues” on page 2-7.See “What is Auto-Connect” on page 2-13 for information about automatically connecting to an adapter after the first connection has been made.If this is the initial set up, you will not see Steps 7 and 8. Proceed to “First Time Connection Procedures” on page 1-5.Step 7: Connected to the AdapterAfter the laptop connects to the adapter, the TV reads Connected. Please wait. This message appears for only a few seconds. If the TV reads Connected. Please Wait for more than 1 minute, the connection attempt failed. Click the Disconnect button and try connecting again. Step 8: Ready to Use Intel Wireless DisplayAfter the Connected. Please Wait. message disappears, the laptop and TV screen are the same and your adapter is displayed in the Connected adapter field. You are now ready to enjoy and share your favorite pictures, videos, and music. If you want to move Intel Wireless Display out of the display area, use the minimize button instead of the close button.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-5v1.0, January 2011First Time Connection ProceduresThis section continues from the end of Step 6 in the Using Intel Wireless Display section. Follow the steps below to complete the initial set up.Changing the TV InputDifferent TV brands have various methods of changing the TV input. Five of the most common processes are covered here. If these options do not cover your TV, consult your TV owner’s manual for additional help.• Some TV remote controls have buttons labeled HDMI, HDMI 1, HDMI 2, A\V, and so on. Push the appropriate button to choose the TV input.• Other TV remote controls include a button labeled Input, Source, TV, or TV/Video. Press this button to cycle the TV through the input options.• Pressing the Input button on some remote controls results in a list of inputs on the TV screen. Simply select the desired input.• Input selection happens on some TVs by pressing the Input button on the front or side panel of the TV screen. Simply press the button until the desired input is selected.• Sometimes the inputs are located beneath the regular channels on the TV. Try selecting the lowest TV channel and then going down one channel.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-6v1.0, January 2011Step 1: Entering a Security CodeWhen the Enter security code screen appears, type the security code shown on the TV. Figure 1-3The security code numbers shown above are for example only! The numbers on your TV will be different. Type the numbers from your TV into the field displayed on your laptop screen:Figure 1-4On your TV, click the Continue button after typing the security code. To stop the set up process click Cancel. For security code questions, see “Security Code Issues” on page 2-3.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-7v1.0, January 2011Step 2: Security Configuration SuccessfulThe Security configuration successful TV message indicates a correct security code entry. Step 3: Adapter is ConnectedAfter the laptop connects to the adapter, the TV shows Connected. Please wait. This message appears for only a few seconds. If the TV reads Connected. Please wait for more than 1 minute, the connection attempt failed. For help, see the “Common Solutions to Many Issues” on page 2-7.Step 4: Rename AdapterAfter entering the security code, you may type a new descriptive name for the adapter. Figure 1-5The example above has the name My Living Room. This new name will be used in all future connections from the laptop to this adapter. If you have more than one adapter, changing the default name makes it easier to identify each adapter. When finished click the Continue button.Note: The valid character set for adapter names are upper and lower case letters A through Z, numbers and punctuation marks, also defined as ASCII characters 32 through 126.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-8v1.0, January 2011Step 5: Finishing the Initial Set Up ProcessAfter the Connected. Please wait message disappears, the laptop screen and TV screen are the same. Congratulations! You have successfully completed the set up process! Click the Registerlink to register your adapter and receive product support and software updates. When you are done registering your product, click the Finish button to exit the set up process.If the laptop and TV are not displaying the same image, see “Common Solutions to Many Issues” on page 2-7.If the screen needs adjusting, click the Adjust your display settings link. For help, see “How do I Adjust the TV Display Image?” on page 2-11.Initial Set Up Troubleshooting• If the TV display shows areas of black around the edges or appears too big, click the Adjustyour display settings link. For screen adjustment help, see “How do I Adjust the TV Display Image?” on page 2-11.• If the TV image is rough, frozen, or delayed, close the application and try connecting again. If this does not help, see “TV Image is Rough, Frozen or Delayed” on page 2-3.• If the audio is not correct, adjust the volume using the TV remote. If this does not solve the issue, see “How do I Adjust the Audio?” on page 2-11.• If both the application and the TV screen show that you are connected, but they are not showing the same image, the laptop’s firewall may be stopping the connection. For firewall help, see “Firewall Issues” on page 2-6.• If the TV screen is blank, the application may have learned an incorrect display setting. For help, see “How do I Train My Displays?” on page 2-12. The TV screen may also be blank if the adapter is too warm after being used for a long time. (The adapter is not designed to be connected for more than four hours.) If this is the case, do not use the adapter until it has cooled down.DisconnectingTo disconnect from the adapter, click the Disconnect button.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual1-9v1.0, January 2011ExitingTo exit Intel Wireless Display, click the Disconnect button, wait until the adapter disconnects, and click the Close Window button (red x) in the upper right corner of application window. If you click the Close Window button while still connected, you are asked if you want to close the connection. Click Yes to exit or No to cancel exiting. To not view this screen again, select the Don’t ask me next time check box.If you would like to turn off Intel My WiFi Technology after closing the application, click the Intel My WiFi Technology icon in the Windows taskbar and choose Disable Intel My WiFi Technology.
2-1v1.0, January 2011Chapter 2 TroubleshootingLook through the Troubleshooting contents for a topic that comes closest to describing your problem. If you are unable to resolve the problem after reading through the Troubleshooting topics, search the FAQ topics. For additional help, visit http://kbserver.netgear.com/products/PTV2000.asp.Initial Set Up ProblemsCords and CablesThe power cord connects to the rear panel of the adapter. Plug the other end of the power cord into an electrical outlet. The HDMI cable connects to the rear panel as shown: HDMIPowerFigure 2-1Only connect either the HDMI cable or the audio/video cable, not both. An HDMI cable will produce higher quality images than an audio/video cable. An HDMI cable is provided in the package with the Push 2 TV adapter. (Audio/video cables can be found at electronics stores.) If you use an audio/video cable, match the connectors to the correct colors on the adapter (yellow,
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-2v1.0, January 2011white, and red). Connect each cord and cable into their correct inputs on the TV. (See your TV owner’s manual if needed.) Once plugged in, make sure the cords and cables are pushed all the way into their correct input positions.Using the composite video cable (the yellow input on the Audio/Video cable) may cause the TV image to be off-centered. Consult the TV owner’s manual for image adjustment.On/Off ButtonThe On/Off button is located on the back of the adapter. On/OffFigure 2-2If the adapter is not turning on, make sure the power cord is pushed all the way into both the wall outlet and the adapter. If power is not getting to the adapter, there might be a faulty power cord.Changing the TV InputDifferent TV brands have various methods of changing the TV input. Five of the most common processes are covered here. If these options do not cover your TV, consult your TV owner’s manual for additional help.• Some TV remote controls have buttons labeled HDMI, HDMI 1, HDMI 2, A\V, and so on. Push the appropriate button to choose the TV input.• Other TV remote controls include a button labeled Input, Source, TV, or TV/Video. Press this button to cycle the TV through the input options.• Pushing the Input button on some remote controls results in a list of inputs on the TV screen. Simply select the desired input.• Input selection happens on some TVs by pressing the Input button on the front or side panel of the TV screen. Simply press the button until the desired input is selected.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-3v1.0, January 2011• Sometimes the inputs are located beneath the regular channels on the TV. Try selecting the lowest TV channel and then go down one channel. Adapter Encountered a Problem on StartupThe adapter is experiencing technical difficulties. First turn the adapter off and back on again. If this does not resolve the issue, see “Adapter Does Not Work” on page 2-6.There are No Adapters DetectedIt may be necessary to scan multiple times. If rescanning does not solve the issue, make sure the adapter is on and the TV is displaying the To get started screen. Also, try moving the laptop or the adapter to different places in the room. The adapter and TV should be in the same room to work properly. If this does not work, see “Common Solutions to Many Issues” on page 2-7.Security Code IssuesThe phrase, That security code is not correct... in the Security Code section, means the wrong security code has been entered. Make sure to type the code exactly as shown on the TV screen. The security code number will change after an incorrect entry.If the connection fails right after a correct security code is entered, it is necessary to connect again and retype the security code.TV Image is Rough, Frozen or DelayedTo fix a rough, frozen, or delayed image try each of the following steps individually.• Check the laptop’s CPU status. Right-click on the taskbar and choose Start Task Manager. In the Task Manager window click the Processes tab. Under the CPU heading, check WiDiApp.exe. If the WiDiApp.exe CPU number is 80 or above, save documents, and close unused applications. • Check the network link speed. Right click on the taskbar and choose Start Task Manager. In the Task Manager window click the Networking tab. The link speed should be higher than 36 Mbps. If not, try moving the adapter to a different position that is farther away from other electronic equipment, or closer to the laptop. If this does not help, try disconnecting the adapter and connecting again.• Change the channel on the wireless router. See the router’s manual for channel changing instructions. (If you are not using a router, see the next solution.)
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-4v1.0, January 2011• If you are not connected to a router change the wireless channel. Open Intel My WiFi Utility by clicking on the Intel My WiFi Technology icon in the taskbar and selecting Open Intel My WiFi Utility. Use the help document in Intel My WiFi Utility and search for AccessPoints. In the results, click Advanced Settings and follow the instructions.Your Video Mode has Changed...The video display resolution may change while using Intel Wireless Display. This can happen regardless of whether you change the display resolution manually or it is changed by another application. On the Your Video Mode has Changed... screen, click the Restore settings and resume connection button to allow the application to automatically reset the display to the correct settings. Choosing Keep settings and close connection results in the display session ending. The supported video display settings are: Screen resolution (in landscape or portrait mode) = 1280 x 720, 1280 x 768, or 1280 x 800. Color depth = 32-bit. In extended mode Wireless Display will support 1920 x 1080.Unsupported Audio ModeThe laptop must have specific audio settings for Intel Wireless Display to work correctly. Adjusting these settings to a unsupported audio mode is not recommended. The Unsupportedaudio mode screen appears if the audio display settings need adjusting. To restore the audio settings to the correct values:1. In the Unsupported audio mode window click the Adjust audio settings button.2. In the Sound window, double click Speakers.3. On the Advanced tab choose either 16 bit, 44100 Hz (CD Quality) or 48000 Hz (DVD Quality) and click OK. (Unpredictable results may occur if different audio modes are used.)Intel Wireless Display Requires a Different Security ProfileSecurity Profile is IncorrectThe wireless security settings have been reconfigured using the Intel My WiFi Utility. To allow the application to automatically choose the correct profile:1. Right-click the Intel My WiFi Technology icon on right end of the taskbar.2. Select Disable Intel My WiFi Technology.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-5v1.0, January 20113. Click the Scan for available adapters button on Intel Wireless Display. While scanning, the application automatically enables Intel My WiFi Technology and selects the correct security profile.Manually Setting the Correct Security ProfileIf the steps above do not automatically select the correct security profile, click the Intel My WiFi Utility icon in the taskbar and select Open Intel My WiFi Utility. Use the help document in Intel My WiFi Utility and search for Security. In the results, click Security Settings and follow the instructions.Your Wireless is OffNormally, Wi-Fi allows the laptop to connect to the router for wireless Internet access. A new feature included with Intel Wireless Display uses Wi-Fi to wirelessly connect the laptop to the TV through the adapter.For this new Wi-Fi connection to work correctly, three switches must be turned on. The first switch is the hardware switch. It is usually located around the edge of the laptop or above the keyboard. It may be identified by a pole with two half circles on each side. Check the laptop manual for the exact location. Turn the switch on and scan again.When needed, the other two switches are automatically turned on by the application. If it is still impossible to connect because the application is not automatically turning the other switches on, see “Common Solutions to Many Issues” on page 2-7.Intel My WiFi Technology is DisabledIntel My WiFi Technology allows the laptop to become a Wi-Fi access point for other laptops. If the laptop screen reads Intel My WiFi Technology is disabled, click the Scan for available adapters button to automatically enable Intel My WiFi Technology. If the Wi-Fi is already on, Intel Wireless Display will automatically enable Intel My WiFi Technology. If the Wi-Fi is off, the application asks if you would like to turn on Intel My WiFi Technology. Select Yes and scan again. If this does not work, see “Common Solutions to Many Issues” on page 2-7.Unsupported Laptop HardwareFor Intel Wireless Display to run, Intel My WiFi Technology must be installed, and the laptop must have an Intel Core i7, i5, or i3 processor with Intel Graphics Media Accelerator HD.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-6v1.0, January 2011Firewall IssuesSometimes the laptop’s firewall will block the Wi-Fi connection between the laptop and the adapter. If this is the case, the laptop's firewall settings must be changed. The following instructions apply to a Microsoft Windows Firewall. To allow Intel Wireless Display through a different firewall, see that firewall's product manual. There may be inconsistent results allowing the application through a firewall that is not a Microsoft Windows firewall.1. Click on the Windows Start icon and type in the search field Allow a program through a Windows Firewall.2. In the search results, click Allow a program through Windows Firewall.3. In the firewall control panel, make sure the Name,Private, and Public check boxes are selected for both WiDiApp and Wireless PAN DHCP Server.4. When done, click OK and connect again.Windows Power SavingMicrosoft Windows software may be set to dim the display or put the computer to sleep after a period of time. To avoid the laptop’s screen dimming while using Intel Wireless Display, change the laptop’s power settings by following these steps:1. Click the Windows Start icon.2. Type Power Options in the search field and click the Power Options result.3. Under the Select a Power Plan heading, make sure the Balanced radio button is selected.4. Click Change Plan Settings next to the current plan.5. Change the Dim the display,Turn of the display, and Put the computer to sleep options under either On Battery and Plugged in headings to a longer time setting.Could Not Obtain a Network AddressTo correct this issue, try closing Intel Wireless Display and restarting the laptop. The laptop’s firewall could be blocking the adapter’s request for a network address. To allow the address request through a firewall, see “Firewall Issues” on page 2-6. If this does not resolve the issue, see “Common Solutions to Many Issues” on page 2-7.Adapter Does Not WorkIf the adapter is not working, try the solutions found in “Common Solutions to Many Issues” on page 2-7 before following the instructions below.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-7v1.0, January 2011If the adapter will not turn on, or it is impossible to update the firmware, perform a factory reset.Figure 2-3Press and hold the Reset button while pushing the power button off and then on. Continue to hold the Reset button down until the adapter LED begins flashing. Try connecting again. After the factory reset, the adapter connection settings will be erased and the firmware will need to be updated.Checking the Access Point FrequencyIntel Wireless Display only works at 2.4GHz on both the PAN connection to the TV and LAN connection to the Internet via a home wireless router. The Wi-Fi standard uses both 2.4GHz and 5GHz frequency bands. Most home wireless routers are only 2.4GHz and have no interoperability issue with Intel Wireless Display. Some newer 802.11n home wireless routers are starting to include support for both frequency bands. When using Intel Wireless Display, while also connected to the Internet via your wireless router, make sure the connection to the router is set to 2.4GHz.After making the changes required, it may be necessary to disable/enable Intel My WiFi Technology using the following steps:1. Right-click the Intel My WiFi Technology icon on right end of the taskbar.2. Select Disable Intel My WiFi Technology.3. Click the Scan for available adapters button on Intel Wireless Display. While scanning, the application automatically enables Intel My WiFi Technology.Common Solutions to Many IssuesThis section describes five procedures to try if the other troubleshooting sections have not helped. Try each solution one at a time starting with Step 1. For additional help, visit http://kbserver.netgear.com/products/PTV2000.asp.1. Close Intel Wireless Display, reopen the application, scan for available adapters, and connect.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-8v1.0, January 20112. Shut down the laptop, restart, open the application, scan for available adapters, and connect.3. Reset the adapter, scan for available adapters, and connect. For help resetting the adapter, see “How do I Reset the Adapter?” on page 2-9.4. Check the laptop’s firewall settings. A firewall may be blocking the application. For firewall help, see “Firewall Issues” on page 2-6.5. Try updating the firmware. For firmware update instructions, see “How do I Update the Firmware?” on page 2-9.Known IssuesThis section lists known Intel Wireless Display issues and workarounds.• After disconnecting from the application, it may be necessary to manually enable the laptop's sound. For audio help see “How do I Adjust the Audio?” on page 2-11.• The application will usually not work if it is located in the Windows startup group.• Wait until Microsoft Windows has fully booted before opening Intel Wireless Display.• If the media application in use can only be set to mute or unmute both the laptop and TV at the same time, it is recommended to use a different media application.• Pressing Control + Alt + Delete on the laptop might freeze the TV image.• For analog TVs, the adapter does not support NTSC (National Television System Committee) format 4.43 variations on the composite interface. See the TV owner’s manual for NTSC variation information.• Changing the wireless LAN or connection settings when Intel Wireless Display is connected may cause momentary disruption of or end the connection.FAQsLook through the FAQ contents for a topic that comes closest to describing your problem. If you are unable to resolve the problem after reading through the FAQ topics, search the Troubleshooting topics. For additional help, visithttp://kbserver.netgear.com/products/PTV2000.asp
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-9v1.0, January 2011How do I Change the Adapter Display LanguageTo change the adapter display language, use the recessed button (7) while the adapter is on the ready screen shown.• A short press (less than half a second) will step forward through the languages.• A long press (more than half but less than one and a half seconds) will step backward through the languages. Warning: Pressing the button for more than 5 seconds will clear the security profiles saved in the adapter, which will require you to repeat the first-time connection procedure.The language change will immediately be reflected on your TV screen.How do I Update the Firmware?If the firmware needs updating, there will be an Update available button on the Adapter Properties page. (The Properties button is only available if you are currently connected to an adapter.) Click the Update available button to begin the update process. Once the update begins the TV screen will read Updating adapter. Please wait. After the procedure is complete, the adapter automatically disconnects from the laptop. Scan again to connect to the adapter.How do I Reset the Application Settings?Resetting reverts the application back to its out-of-the-box state. To reset, click Help and select About. Click Reset Settings. To proceed with the reset, click the Yes button on the Reset Intel Wireless Display settings page.After starting Intel Wireless Display, all detected adapters will be displayed as not previously connected. However, it will not be necessary to enter a security code since the security settings are stored in the adapter. How do I Reset the Adapter?If the adapter is not responding correctly, and resetting the application has not helped, try restarting the adapter. Push the power button once to turn the adapter off, and push it again to turn it on. After the To get started screen appears on the TV, rescan before trying to connect.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-10v1.0, January 2011How do I Clear the Adapter Memory?Clearing the adapter’s memory erases security settings and the user modified adapter name. This is helpful if you choose to sell your adapter, or if a neighbor came to your house and connected to your adapter, but now you do not want them to accidentally connect from their house.To clear the adapter’s memory, press and hold the Reset button on the back of the adapter for more than 5 seconds or until the LED starts blinking. Clearing the adapter memory requires you to enter the security code displayed on the TV in order to connect again.Can I Close the Laptop Lid and Still Use Intel Wireless Display?Closing the lid of the laptop may put the system to sleep or turn it off, and as a result, end the Intel Wireless Display session. To close the lid and continue using the application:1. Click the Windows Start icon and type Closing the lid in the search field.2. Click the Change what closing the lid does link.3. Next to the When I close the lid heading and under both the On battery and Plugged in headings, select Do nothing.4. Click the Save changes button.What are Adapter Properties?Adapter Properties Definitions•Adapter Name. This is either the default factory name or the name you choose in the initial set up process. It is okay to change the name at anytime. Just type a new name. If the default “Name” is deleted and the field is left empty, the application will restore the name to the previous value. NOTE: The valid character set for adapter names are upper and lower case letters A through Z, numbers and punctuation marks, also defined as ASCII characters 32 through 126.•Network address. This is the IP (Internet Protocol) address.•Adapter ID. A preset and unchangeable number set by the adapter.•Adapter Model. This is the model name of the adapter currently connected.•Adapter firmware version. The version of the application. If a Web update is required, click the Update Available button.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-11v1.0, January 2011•Show the cursor. By default, Intel Wireless Display enables the cursor to be shown on the TV. To make the mouse cursor disappear on the TV, clear this check box. Resetting Intel Wireless Display will return the cursor to its default setting.•Automatically connect. Allows this adapter to be set as the auto-connect adapter. See “Whatis Auto-Connect” on page 2-13 for more details.•Register. Register your adapter to obtain support and get the latest software updates.Audio/Visual TuningIf the laptop display is cropped or not filling the entire TV screen, see “How do I Adjust the TV Display Image?” on page 2-11. To troubleshoot audio problems, see “How do I Adjust the Audio?” on page 2-11.Why does My Laptop's Color Look Different on My TV?Sometimes colors on the TV screen and the laptop may be a slightly different. To match the colors, change the TV settings until the screens are the same. (See your TV manual for color adjustment help.)How do I Adjust the TV Display Image?If the laptop display is cropped or not filling the entire TV screen, the image needs to be adjusted. To adjust the TV image click the Properties button. In the Adapter properties page click the Resize TV picture button. On the next page, click the plus icon to increase the size, or the minus icon to decrease the size. When the image is correct, click OK to return to the previous page. If the image still does not fit the entire TV screen, try adjusting the TV settings.How do I Adjust the Audio?Once a connection begins, the laptop’s sound is muted. When the connection ends, the laptop’s sound is enabled. Sample Audio TestingWhen connected, clicking the Test audio button on the Adapter properties page takes you to an audio test page. If you do not hear audio after clicking the Play sample button, increase the volume on the TV speakers by using the TV remote.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-12v1.0, January 2011Global Volume ControlUsually, the laptop’s sound is muted after connecting to Intel Wireless Display. Sometimes, however, other applications may automatically turn on the laptop’s sound. This will result in hearing the same sound from the laptop before hearing it from the TV. To turn the volume off, click the little speaker icon located on the far right of the taskbar. This will bring up the Global Volume Control pop up window. Click the speaker icon just below the slider to mute the laptop’s sound. If the laptop’s sound keeps coming back on, try turning the volume all the way down using the slider in the pop up window instead of muting. Moving the volume slider will automatically unmute the laptop’s speakers. Windows Audio MixerAttempting to change audio settings in the Windows Audio Mixer while using the application, may result in a connection disruption. (The Windows Audio Mixer is found by clicking the Mixerlink in the Global Volume Control.) Usually the connection will automatically reestablish. The TV image may flicker during this time. If the connection does not automatically reestablish, manually reconnect.Changing the Sound using the Windows Control PanelTo bring up the audio device window go to the start menu, type audio device in the search field, and press the Enter key. On the Playback tab, make sure the green circle with a check mark is on local speakers.How do I Train My Displays?Training Two DisplaysWhile using a laptop and a TV, sometimes the laptop’s display settings may be inadvertently changed. This may result in the TV showing a blank screen after connecting. If this is the case, simultaneously push the Windows button and the letter P on the keyboard. Select Duplicate in the popup window to make both laptop and TV screens the same.Training Three DisplaysWhile using a laptop, a TV, and an external monitor sometimes the laptop’s display settings may be inadvertently changed. This may result in the TV showing a blank screen after connecting. The laptop is capable of only displaying on two screens at the same time including its own. The TV screen needs to be one of the two selected screens.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-13v1.0, January 2011To select which screens to use:1. Simultaneously push the Windows button and the letter P on the keyboard. Select Duplicatein the popup window. If your laptop screen is not duplicated on your TV, proceed to the next step.2. Click the Windows Start icon.3. In the search field, type Adjust screen resolution and press Enter.4. Next to the heading Display, select the option other than Multiple Monitors.5. Next to the heading Multiple displays, choose either one of the duplicate combinations.6. To try the new settings, click Apply.7. If the laptop screen is showing on the desired combination of displays, click the Keep changesbutton in the pop up dialog box then click OK. Otherwise, click Revert and go back to Step 4 and choose the other combination in Step 5.Can I play DVDs with Intel Wireless Display?Many DVDs and Blu-ray discs include copy protection mechanisms which prevent playback over unprotected outputs. Intel Wireless Display is currently an unprotected output; and as a result, many DVDs and Blu-ray Discs will not work. However, personal content (pictures, home movies, etc) that you have burned to DVDs and Blu-ray Discs are not protected in the same manner and will work with Intel Wireless Display.How do I Contact Customer Support?Contact your computer or adapter manufacturer to get support for your specific product. Visit http://www.intel.com/go/wirelessdisplay to access general Intel Wireless Display support forums.What is Auto-ConnectThis is a feature which enables you to set an adapter as your default adapter for an automatic connection. This action is somewhat similar to selecting a default printer. Only one adapter at a time can be set as the auto-connect adapter. In addition, the auto-connect feature can only be enabled after you have successfully connected the first time and completed the security configuration. Auto-connect is only an attempt to connect, and it may fail in the same ways that a manual connection could fail.There are two instances where the auto-connect is attempted.
Push 2 TV Adapter (PTV2000)/Intel Wireless Display User Manual2-14v1.0, January 20111. If the auto-connect adapter is discovered after initial launch, a connection attempt will be made2. If the auto-connect adapter is already in the list when the application is relaunched including pressing the bezel button, a connection attempt will be made. In this case, if a connection is made it will typically be faster than in case 1, because the application is already running and a new scan is not performed.There are two ways to select the auto-connect adapter.1. On the Adapter properties page, there is an Automatically connect to this adapter checkbox. If this check box is selected, this adapter will be chosen as the auto-connect adapter. Note that any other adapter that was previously selected for auto-connect will no longer have its auto-connect property set.2. In the Detected adapters list on the Intel Wireless Display home screen, right clicking on an adapter that has previously been connected shows an Auto-connect property in the context menu (popup menu). A check indicates if this adapter is currently set as the auto-connect adapter or not. Selecting that menu item will change the auto-connect state of the adapter.
A-1v1.0, January 2011Appendix ATechnical SpecificationsFeature DescriptionCompatible laptops Intel Core i3, i5, or i7 processorIntel Graphics Media Accelerator HD graphics adapterIntel WiFi Link wireless networking adapterMicrosoft Windows 7 operating systemIntel Wireless Display softwareNetwork interface IEEE 802.11 a/b/g/n wirelessPower 12V/1APhysical dimensions (d x w x h) 106 mm x 138 mm x 32 mmWeight 180 gOperating temperature 0 to 40º C (32 to 105º F)Electromagnetic compliance CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22) Class B, C-TickPower adapter safety approval CE mark, Commercial UListed (UL 1950), C-Tick
B-1v1.0, January 2011Appendix BRelated DocumentsThis appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.Document LinkWindows XP and Vista Wireless Configuration Utilitieshttp://documentation.netgear.com/reference/enu/winzerocfg/index.htmInternet Networking and TCP/IP Addressinghttp://documentation.netgear.com/reference/enu/tcpip/index.htmWireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htmPreparing a Computer for Network Accesshttp://documentation.netgear.com/reference/enu/wsdhcp/index.htmVirtual Private Networking (VPN) http://documentation.netgear.com/reference/enu/vpn/index.htmGlossary http://documentation.netgear.com/reference/enu/glossary/index.htm

Navigation menu