Netgear orporated 11100154 ProSafe Dual Band Wireless-N Access Point User Manual

Netgear Incorporated ProSafe Dual Band Wireless-N Access Point

UserManual.wiki >

Netgear orporated >

11100154 User Manual >

Contents

User Manual

350 East Plumeria DriveSan Jose, CA 95134USAApril, 2011202-10826-01v1.0ProSafe Dual Band Wireless-N Access Point WNDAP360Reference Manual

Contents | 3ContentsChapter 1 IntroductionAbout the ProSafe Dual Band Wireless-N Access Point WNDAP360 . . . . .6What Is In the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Key Features and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Supported Standards and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . .8Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8802.11b/g/n and 802.11a/n Standards–Based Wireless Networking . . . 10Autosensing Ethernet Connections with Auto Uplink . . . . . . . . . . . . . . .10Hardware Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Top Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Bottom Panel with Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Chapter 2 Installation and Basic ConfigurationWhat You Need before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Wireless Equipment Placement and Range Guidelines . . . . . . . . . . . . .14Ethernet Cabling Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15LAN Configuration Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Computer Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Install and Configure the Wireless Access Point . . . . . . . . . . . . . . . . . . . .15Connect the Wireless Access Point to Computer. . . . . . . . . . . . . . . . . . 16Log In to the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . .17Configure Basic General System Settings and Time Settings . . . . . . . .18Configure IP Settings and Optional DHCP Server Settings . . . . . . . . . .20Configure Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Configuring 802.11b/bg/ng Wireless Settings . . . . . . . . . . . . . . . . . . . . 24Configuring 802.11a/na Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . 26Operating Frequency (Channel) Guidelines. . . . . . . . . . . . . . . . . . . . . .28Test Basic Wireless Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Mount the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Ceiling Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Desk Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Chapter 3 Wireless Configuration and SecurityWireless Data Security Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37Before You Change the SSID, WEP, and WPA Settings . . . . . . . . . . . . 38

4 | Contents ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Configure and Enable Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . . 40Configure RADIUS Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Restrict Wireless Access by MAC Address . . . . . . . . . . . . . . . . . . . . . . . . 51Schedule the Wireless Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Configure Basic Wireless Quality of Service . . . . . . . . . . . . . . . . . . . . . . . 53Chapter 4 ManagementEnable Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55SNMP Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Secure Shell and Telnet Management . . . . . . . . . . . . . . . . . . . . . . . . . . 57Upgrade the Wireless Access Point Software . . . . . . . . . . . . . . . . . . . . . . 58Manage the Configuration File or Reset to Factory Defaults . . . . . . . . . . . 61Save the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Restore the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Restore the Wireless Access Point to the Factory Default Settings. . . . 63Reboot the Wireless Access Point without Restoring the Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Change the Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Enable the Syslog Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Monitor the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67View System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Monitor Wireless Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69View the Activity Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Traffic Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Enable Rogue AP Detection and Monitor Access Points. . . . . . . . . . . . . . 73Enable and Configure Rogue AP Detection . . . . . . . . . . . . . . . . . . . . . . 73View and Save Access Point Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74Chapter 5 Advanced ConfigurationSpanning Tree Protocol and 802.1Q VLAN . . . . . . . . . . . . . . . . . . . . . . . . 76Hotspot Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Configure Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Configure Advanced QoS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Configure Wireless Bridging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Configure a Point-to-Point Wireless Network . . . . . . . . . . . . . . . . . . . . . 84Configure a Point-to-Multipoint Wireless Network . . . . . . . . . . . . . . . . . 87Configure the Wireless Access Point for Repeater Mode . . . . . . . . . . . 91Configure the Wireless Access Point for Client Mode . . . . . . . . . . . . . . 94Chapter 6 TroubleshootingBasic Functioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97No LEDs Are Lit on the Wireless Access Point . . . . . . . . . . . . . . . . . . . 97The Active LED or the LAN LED Is Not Lit . . . . . . . . . . . . . . . . . . . . . . . 97The WLAN LED Does Not Light Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98You Cannot Access the Internet or the LAN from a Wireless-Capable Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Contents | 5ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual You Cannot Configure the Wireless Access Point from a Browser . . . . . .99When You Enter a URL or IP Address a Time-Out Error Occurs. . . . . . . .99Troubleshooting a TCP/IP Network Using the Ping Utility . . . . . . . . . . . .100Testing the LAN Path to Your Wireless Access Point . . . . . . . . . . . . .100Testing the Path from Your Computer to a Remote Device . . . . . . . . .101Problems with Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101Use the Packet Capture Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102Appendix A Supplemental InformationTechnical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105Appendix B Command-Line ReferenceAppendix C Notification of ComplianceIndex

Chapter 1. Introduction | 611. IntroductionThis chapter introduces the ProSafe Dual Band Wireless-N Access Point WNDAP360 and describes some of the key features. This chapter includes the following sections:• About the ProSafe Dual Band Wireless-N Access Point WNDAP360 on this page• What Is In the Box? on page 7• System Requirements on page 7• Key Features and Standards on page 7• Hardware Description on page 11About the ProSafe Dual Band Wireless-N Access Point WNDAP360The ProSafe Dual Band Wireless-N Access Point WNDAP360 is the basic building block of a wireless LAN infrastructure. It provides 2.4 GHz 802.11b/g/n and 5 GHz 802.11a/n connectivity between wired Ethernet networks and radio-equipped wireless notebook systems, desktop systems, print servers, and other devices.The wireless access point provides wireless connectivity to multiple wireless network devices within a fixed range or area of coverage—interacting with a wireless network interface card (NIC) through an antenna. Typically, an individual in-building wireless access point provides a maximum connectivity area of about a 500-foot radius. The ProSafe Dual Band Wireless-N Access Point WNDAP360 can support up to 64 users simultaneously in a range of several hundred feet.The ProSafe Dual Band Wireless-N Access Point WNDAP360 acts as a bridge between the wired LAN and wireless clients. Connecting multiple wireless access points through a wired Ethernet backbone can further increase the wireless network coverage. As a mobile computing device moves out of the range of one wireless access point, it moves into the range of another. As a result, wireless clients can freely roam from one wireless access point to another and still maintain seamless connection to the network.The autosensing capability of the ProSafe Dual Band Wireless-N Access Point WNDAP360 allows packet transmission at up to 300 Mbps, or at reduced speeds to compensate for distance or electromagnetic interference.

Chapter 1. Introduction | 7ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual What Is In the Box?The product package should contain the following items:• ProSafe Dual Band Wireless-N Access Point WNDAP360 • Power adapter and cord (12 VCD, 1.0A)• Straight-through Category 5 Ethernet cable• ProSafe Dual Band Wireless-N Access Point WNDAP360 Installation Guide• Resource CD, which includes this manual• Wall-mount kit made up of brackets and hardwareContact your reseller or customer support in your area if there are any missing or damaged parts. Refer to the NETGEAR website at http://kbserver.netgear.com/main.asp for the telephone number of customer support in your area. You should keep the Installation Guide, along with the original packing materials, and use the packing materials to repack the wireless access point if you need to return it for repair. To qualify for product updates and product warranty, NETGEAR encourages you to register on the NETGEAR website at http://my.netgear.com/registration/login.aspx.System RequirementsBefore installing the wireless access point, make sure that your system meets these requirements:• A 10/100/1000 Mbps local area network device such as a hub or switch• The Category 5 UTP straight-through Ethernet cable with RJ-45 connector included in the package, or one like it• A 100–120V, 50–60 Hz AC power source• A Web browser for configuration, such as Microsoft Internet Explorer 6.0 or later, or Mozilla 1.5 or later• At least one computer with the TCP/IP protocol installed• An 802.11a/n or 802.11b/g/n-compliant devices, such as the NETGEAR WG511 Wireless AdapterKey Features and StandardsThe ProSafe Dual Band Wireless-N Access Point WNDAP360 is easy to use and provides solid wireless and networking support. It also offers a wide range of security options.

8 | Chapter 1. Introduction ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Supported Standards and ConventionsThe ProSafe Dual Band Wireless-N Access Point WNDAP360 supports the following standards and conventions:• Standards compliance. The wireless access point complies with the IEEE 802.11 b/g standards for wireless LANs, and is Wi-Fi certified for 802.11n standard.• Full WPA and WPA2 support. The wireless access point provides WPA and WPA2 enterprise-class strong security with RADIUS and certificate authentication as well as dynamic encryption key generation. The WPA-PSK and WPA2-PSK preshared key authentication is without the overhead of RADIUS servers but with all of the strong security of WPA.• Multiple BSSIDs. The wireless access point supports multiple BSSIDs. When a wireless access point is connected to a wired network and a set of wireless stations, it is called a basic service set (BSS). The basic service set identifier (BSSID) is a unique identifier attached to the header of packets sent over a WLAN that differentiates one WLAN from another when a mobile device tries to connect to the network.The multiple BSSID feature allows you to configure up to eight SSIDs on your wireless access point and assign different configuration settings to each SSID. All the configured SSIDs are active, and the network devices can connect to the wireless access point by using any of these SSIDs.• DHCP client support. DHCP provides a dynamic IP address to PCs and other devices upon request. The wireless access point can act as a client and obtain information from your DHCP server; it can also act as a DHCP server and provide network information for wireless clients.• SNMP Support. Support for Simple Network Management Protocol (SNMP) Management Information Base (MIB) management.• 802.1Q VLAN (virtual LAN) support. A network of computers that behave as if they are connected to the same network even though they might actually be physically located on different segments of a LAN. VLANs are configured through software rather than hardware, which makes them extremely flexible. VLANs are very useful for user and host management, bandwidth allocation, and resource optimization. Key FeaturesThe ProSafe Dual Band Wireless-N Access Point WNDAP360 provides solid functionality, including the following features:• Dual Band Concurrent. The wireless access point can operate in both the 2.4 GHz band and the 5 GHz band concurrently.The choice of bands is reflected in the protocol standard supported, as well as the administration screens that are displayed.

Chapter 1. Introduction | 9ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual • Multiple operating modes:-Wireless access point. Operates as a standard 802.11b/g/n or 802.11 a/n wireless access point.-Point-to-point bridge. In this mode, the wireless access point communicates only with another bridge-mode wireless station or wireless access point. Network authentication should be used to protect this communication. -Point-to-multipoint bridge. Select this only if this wireless access point is the master for a group of bridge-mode wireless stations. The other bridge-mode wireless stations send all traffic to this master, and do not communicate directly with each other. Network authentication should be used to protect this traffic. -Wireless repeater. In this mode, the wireless access point does not function as an access point but communicates only with wireless stations that function in repeater mode, point-to-point bridge mode, and point-to-multipoint-bridge mode. Network authentication should be used to protect this communication.-Client. In this mode, the wireless access point functions as a client bridge only, and sends all traffic to a remote wireless access point or peer device.• Hotspot settings. You can allow all HTTP (TCP, port 80) requests to be captured and redirected to the URL you specify.• Upgradeable firmware. Firmware is stored in a flash memory. You can upgrade it easily, using only your Web browser, and you can upgrade it remotely. You can also use the command-line interface.• Rogue AP detection. The Rogue AP filtering feature ensures that unknown APs are not given access to any part of the LAN.• Access control. The Access Control MAC address filtering feature can ensure that only trusted wireless stations can use the wireless access point to gain access to your LAN.• Security profiles. When using multiple BSSIDs, you can configure unique security settings (encryption, SSID, and so on) for each BSSID.• Hidden mode. The SSID is not broadcast, assuring only clients configured with the correct SSID can connect.• Secure Telnet command-line Interface. The secure Telnet command-line interface (CLI) enables direct secure access over the serial port and easy scripting of configuration of multiple wireless access points across an extensive network via the Ethernet interface. A Secure Shell (SSH) client is required.• Configuration backup. Configuration settings can be backed up to a file and restored.• Secure and economical operation. Adjustable power output allows more secure or economical operation.• Power over Ethernet. Power can be supplied to the wireless access point over the Ethernet port from any 802.3af-compliant midspan or end-span source.• Autosensing Ethernet connection with Auto Uplink™ interface. Connects to 10/100/1000 Mbps IEEE 802.3 Ethernet networks.• LED indicators. Power/Test, Active, LAN, and WLAN for each radio mode are easily identified.

Chapter 1. Introduction | 11ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Hardware Description This section describes the top and rear hardware functions of the ProSafe Dual Band Wireless-N Access Point WNDAP360.Top PanelThe ProSafe Dual Band Wireless-N Access Point WNDAP360 LEDs are described in the following figure and table:Figure 1. Table 1. Top Panel LEDs Item LED Description1Power/Test Off Power is off.On (green) Power is on.Amber, then blinking green A self-test is running or software is being loaded. During startup, the LED is first steady amber, then goes off, and then blinks green before turning steady green after about 45 seconds. If after 1 minute the LED remains amber or continues to blink green, it indicates a system fault.2Active Off No Ethernet traffic is detected or no link is detected.On or blinking (green) Ethernet traffic is detected.1 2 3 4 5

12 | Chapter 1. Introduction ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Rear PanelFigure 2. The rear panel functions of the ProSafe Dual Band Wireless-N Access Point WNDAP360 are described in the following list:1. Reverse SMA connector for an optional 2.4-GHz antenna.2. Factory default Reset button. Using a sharp object, press and hold this button for about 5 seconds to reset the wireless access point to factory defaults settings. All configuration settings are lost, and the default password is restored. For more information, see Restore the Wireless Access Point to the Factory Default Settings on page 63.3. Console port for connecting to an optional console terminal. The port has an RJ-45 connector and supports the following settings: 9600 K default baud rate, (8) data bits, no (N) parity bit, and one (1) stop bit.4. 10/100/1000BASE-T Gigabit Ethernet (RJ-45) port with Auto Uplink (Auto MDI-X) with IEEE 802.3af Power over Ethernet (PoE) support for connection to a switch or router.3LAN Off 10 Mbps or no link is detected.Amber 10/100 Mbps link is detected.Green 1000 Mbps link is detected.4 2.4 GHz WLAN Off Wireless 802.11b/g/n (2.4 GHz) LAN is not ready or no wireless activity is detected.On or blinking (green) Wireless 802.11b/g/n (2.4 GHz) LAN is ready or wireless activity is detected.5 5 GHz WLAN Off Wireless 802.11n/a (5 GHz) LAN is not ready or no wireless activity is detected.On or blinking (green) Wireless 802.11n/a (5 GHz) LAN is ready or wireless activity is detected.Table 1. Top Panel LEDs (Continued)Item LED Description123 4 567

Chapter 1. Introduction | 13ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 5. Cable security lock receptacle for an optional lock.6. Power socket for a 12 VDC, 1A power adapter.7. Reverse SMA connector for an optional 2.4-GHz antenna.Bottom Panel with Product LabelThe product label on the bottom of the wireless access point’s enclosure displays factory default settings, regulatory compliance, and other information:Figure 3.

Chapter 2. Installation and Basic Configuration | 1422. Installation and Basic ConfigurationThis chapter describes how to install and configure your access point for wireless connectivity to your LAN. This basic configuration will enable computers with 2.4 GHz 802.11b/g/n or 5 GHz 802.11 a/n wireless adapters to connect to the Internet, or access printers and files on your LAN. In planning your wireless network, consider the level of security required. Chapter 3, Wireless Configuration and Security, describes how to set up wireless security for your network. This chapter includes the following sections:• What You Need before You Begin on this page• Install and Configure the Wireless Access Point on page 15• Test Basic Wireless Connectivity on page 28• Mount the Wireless Access Point on page 29Note: In this chapter and in all further chapters, the WNDAP360 is referred to as the wireless access point.What You Need before You BeginYou need to consider the following guidelines and requirements before you can set up your wireless access point. See also System Requirements on page 7.Wireless Equipment Placement and Range GuidelinesThe range of your wireless connection can vary significantly based on the location of the wireless access point. The latency, data throughput performance, and notebook power consumption of wireless adapters also vary depending on your configuration choices.Note: Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the wireless access point. For complete performance specifications, see Appendix A, Supplemental Information.

Chapter 2. Installation and Basic Configuration | 15ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual For best results, place your wireless access point according to the following general guidelines:• Near the center of the area in which your PCs will operate.• In an elevated location such as a high shelf where the wirelessly connected PCs have line-of-sight access (even if through walls).• Away from sources of interference, such as PCs, microwaves ovens, and 2.4-GHz cordless phones.• Away from large metal surfaces or water.• Placing an external antenna in a vertical position provides best side-to-side coverage. Placing an external antenna in a horizontal position provides best up-and-down coverage. (An external antenna does not come standard with the WNDAP360 wireless access point.)• If you are using multiple wireless access points, it is better if adjacent wireless access points use different radio frequency channels to reduce interference. The recommended channel spacing between adjacent wireless access points is five channels (for example, use channels 1 and 6, or 6 and 11, or 1 and 11).The time it takes to establish a wireless connection can vary depending on both your security settings and placement. WEP connections can take slightly longer to establish. Also, WEP encryption can consume more battery power on a notebook computer.Ethernet Cabling RequirementsThe wireless access point connects to your LAN using twisted-pair Category 5 Ethernet cable with RJ-45 connectors.LAN Configuration RequirementsFor the initial configuration of your wireless access point, you need to connect a computer to the wireless access point.Computer Hardware RequirementsTo connect to the wireless access point on your network, each computer needs to have an 802.11b/g/n or 802.11a/n wireless adapter installed.Install and Configure the Wireless Access PointBefore installing the wireless access point, make sure that your Ethernet network is up and working. You will be connecting the wireless access point to the Ethernet network. Then computers with 802.11b/g/n or 802.11a/n wireless adapters will be able to communicate with the Ethernet network.

16 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual In order for this to work correctly, verify that you have met all of the system requirements, shown in System Requirements on page 7.Install and configure your wireless access point in the order of the following sections:1. Connect the Wireless Access Point to Computer on this page.2. Log In to the Wireless Access Point on page 17.3. Configure Basic General System Settings and Time Settings on page 18.4. Configure IP Settings and Optional DHCP Server Settings on page 205. Configure Basic Wireless Settings on page 23.Connect the Wireless Access Point to ComputerTip: Before you place the wireless access point in an elevated position that is difficult to reach, first set up and test the wireless access point to verify wireless network connectivity.To set up the wireless access point:1. Unpack the box and verify the contents.2. Prepare a computer with an Ethernet adapter. If this computer is already part of your network, record its TCP/IP configuration settings. Configure the computer with a static IP address of 192.168.0.210 and 255.255.255.0 as the subnet mask.3. Connect an Ethernet cable from the wireless access point to the computer (point A in the following figure).4. Securely insert the other end of the cable into the wireless access point’s Ethernet port (point B in the following figure)..Figure 4. ABEthernet cableEthernet portWNDAP360

Chapter 2. Installation and Basic Configuration | 17ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 5. Turn on your computer.6. Connect the power adapter to the wireless access point.Tip: The wireless access point supports Power over Ethernet (PoE). If you have a switch that provides PoE, you will not need to use the power adapter to power the wireless access point. This can be especially convenient when the wireless access point is installed in a high location far away from a power outlet.7. Verify the following:Power/Test LED. The Power/Test LED blinks when the wireless access point is first turned on. (To be exact, during startup, the LED is first steady amber, then goes off, and then blinks green.) After about 45 seconds, the LED should stay lit (steady green). If after 1 minute the Power/Test LED is not lit or is still blinking, check the connections and see if the power outlet is controlled by a wall switch that is turned off.Active LED. The Active LED is lit or blinks green when there is Ethernet traffic.LAN LED. The LAN LED indicates the LAN speed: green for 1000 Mbps, amber for 100 Mbps, and no light for 10 Mbps. If the LAN LED is not lit, make sure that the Ethernet cable is securely attached at both ends.WLAN LED. The 2.4 GHz WLAN LED is lit or blinks green when the wireless LAN (WLAN) is ready.WLAN LED. The 5 GHz WLAN LED is lit or blinks green when the wireless LAN (WLAN) is ready.Log In to the Wireless Access PointThe default IP address of your wireless access point is http://192.168.0.100. The wireless access point is set, by default, for the DHCP client to be disabled.To log in to the wireless access point:1. Open a Web browser such as Microsoft Internet Explorer 6.0 or later, or Mozilla Firefox 1.5 or later. 2. Connect to the wireless access point by entering its default address of http://192.168.0.100 into your browser.The Login screen opens3. Enter the default user name of admin and the default password of password.

18 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 4. Click Login. The Web browser displays the basic General system settings screen under the Configuration tab of the main menu as shown in Figure 7 on page 19.Web Management InterfaceThe navigation tabs across the top of the Web Management Interface provide access to all the configuration functions of the wireless access point, and remain constant. The menu items in the blue bar change according to the navigation tab that is selected.Figure 5. The bottom right corner of all screens that allow you to make configuration changes show the Apply and Cancel buttons, and on several screens the Edit button.Figure 6. These buttons have the following functions:• Edit. Allows you to edit the existing configuration.• Cancel. Cancels all configuration changes that you made on the screen.• Apply. Saves and applies all configuration changes that you made on the screen.Configure Basic General System Settings and Time SettingsNote: After you have successfully logged in to the wireless access point, the basic General system settings screen displays.To configure basic system settings:1. Select Configuration > System > Basic > General. The basic General system settings screen displays:

Chapter 2. Installation and Basic Configuration | 19ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 7. 2. Specify the fields as explained in the following table:3. Click Apply to save your settings.To configure time settings:1. Select Configuration > System > Basic > Time. The Time screen displays:Table 2. Basic General System Settings Field DescriptionAccess Point Name This unique name is the wireless access point NetBIOS name. The name is printed on the rear label of the wireless access point. The default is netgearxxxxxx, where xxxxxxx represents the last 6 digits of the wireless access point MAC address. You can replace the default name with a unique name up to 15 characters long. The access point name can be retrieved through SNMP.Country/Region From the Country/Region drop-down list, select the country where the wireless access point is installed.Note: It might not be legal to operate this wireless access point in a region other than one of those identified in this field.

20 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 8. 2. Specify the fields as explained in the following table:3. Click Apply to save your settings.Configure IP Settings and Optional DHCP Server SettingsTo configure the IP settings:1. Select Configuration > IP > IP Settings. The IP Settings screen displays:Table 3. Time System Settings Field DescriptionTime Zone Select the time zone to match your location.Current Time This is a nonconfigurable field that displays the current date and time.NTP Client Enable the Network Time Protocol (NTP) client to synchronize the time of the wireless access point with an NTP server. By default the Enable radio button is selected.Use Custom NTP Server Select this check box to If you want to use a custom NTP server.Note: You need to have an Internet connection to use an NTP server that is not on your local network.Hostname / IP Address Enter the host name or IP address of the custom NTP server. The default is time-b.netgear.com.

Chapter 2. Installation and Basic Configuration | 21ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 9. 2. Specify the fields as explained in the following table:3. Click Apply to save your settings.The wireless access point provides a built-in DHCP server for wireless clients only, which can be especially useful in small networks. When the DHCP server is enabled, the wireless access point provides preconfigured TCP/IP configurations to all connected wireless stations.Table 4. IP Settings Field DescriptionDHCP Client By default, the Dynamic Host Configuration Protocol (DHCP) client is disabled. If you have a DHCP server on your LAN and you select the Enable check box, the wireless access point will receive its IP address, subnet mask, and default gateway settings automatically from the DHCP server on your network when you connect the wireless access point to your LAN.IP Address Enter the IP address of your wireless access point. The default IP address is 192.168.0.100. To change the address, enter an unused IP address from the address range used on your LAN, or enable DHCP the server.IP Subnet Mask Enter the network number portion of an IP address. Unless you are implementing subnetting, enter 255.255.0.0 as the subnet mask.Default Gateway Enter the IP address of the ISP’s router to which the wireless access point will connect.Primary DNS Server Enter the IP address of the primary and secondary DNS servers. A DNS server is a host on the Internet that translates Internet names (such as www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP address of one or two DNS servers to your wireless access point during login. If the ISP does not transfer an address, you need to obtain it from the ISP and enter it manually in this field. Secondary DNS ServerNetwork Integrity Check Select this check box to validate that the upstream link is active before allowing wireless associations. Ensure that the default gateway is configured.

22 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual To configure DHCP server settings:1. Select Configuration > IP > DHCP Server Settings. The DHCP Server Settings screen displays:Figure 10.

Chapter 2. Installation and Basic Configuration | 23ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 2. Specify the fields as explained in the following table:3. Click Apply to save your settings.Configure Basic Wireless SettingsFor proper compliance and compatibility between similar products in your coverage area, you need to correctly configure the 802.11b/g/n and 802.11a/n wireless adapter settings, including the operating channel and country. You also need to correctly configure the basic wireless network settings for wireless devices to connect to your network. For other wireless features, including wireless security, see Chapter 3, Wireless Configuration and Security.Table 5. LAN Settings Field DescriptionDHCP Server Select the DHCP Server check box to enable the DHCP server. Use the default settings or specify the pool of IP addresses to be assigned by setting the starting IP address and ending IP address. These addresses should be part of the same IP address subnet as the wireless access point’s LAN IP address.DHCP Server VLAN ID Enter the DHCP server VLAN ID. The VLAN ID range is between 1 and 4094.Starting IP Address Enter the first address in the range of IP addresses to be assigned to DHCP clients. The default address is 192.168.1.02.Ending IP Address Enter the last address in the range of IP addresses to be assigned to DHCP clients. The default address is 192.168.1.50.Subnet Mask Enter the subnet mask to be used by DHCP clients. The default mask is 255.255.255.0.Gateway IP Address Enter the IP address of the default routing gateway to be used by DHCP clients. The default address is 192.168.0.1.Primary DNS Address Enter the IP address of the primary Domain Name Server (DNS) server available to DHCP clients.Secondary DNS Address Enter the IP address of the secondary DNS server available to DHCP clients.Primary WINS Server Enter the IP address of the primary WINS server for the network.Secondary WINS Server Enter the IP address of the secondary WINS server for the network.Lease Enter the period that the DHCP server grants to DHCP clients to use the assigned IP addresses. The default time is 1 day.

24 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual WARNING!If you configure the wireless access point from a wireless computer and you change the wireless access point’s SSID, channel, or wireless security settings, you will lose your wireless connection when you click Apply. You then need to change the wireless settings of your computer to match the wireless access point’s new settings.Configuring 802.11b/bg/ng Wireless SettingsTo configure the 802.11b/g/n wireless settings:1. Select Configuration > Wireless > Basic > Wireless Settings. The basic Wireless Settings screen displays.2. Specify the fields as explained the following table:Table 6. Basic Wireless Settings Field DescriptionsWireless Mode Select the wireless operating mode that you want to use by selecting one of the following radio buttons:• 11b. 802.11b wireless stations only.• 11bg. Both 802.11b and 802.11g wireless stations can be used.• 11ng. Both 802.11n and 802.11g wireless stations can be used. This is the default setting.Turn Radio On The radio is enabled by default. To turn off the radio, clear the Turn Radio On check box. Doing so disables access through the wireless access point, which can be helpful for configuration, network tuning, or troubleshooting activities.Wireless Network Name (SSID) Enter a 32-character (maximum) service set identifier (SSID); the characters are case-sensitive. The default is NETGEAR_11ng. The SSID assigned to a wireless device needs to match the wireless access point’s SSID for the wireless device to communicate with the wireless access point. If the SSIDs do not match, you will not get a wireless connection to the wireless access point. Scheduler Status This is a nonconfigurable field that show the status of the wireless scheduler. For more information, see Schedule the Wireless Radio on page 52.Broadcast Wireless Network Name (SSID) Select the Yes radio button to enable the wireless access point to broadcasts its SSID, allowing wireless stations that have a null (blank) SSID to adopt the wireless access point’s SSID. Yes is the default setting. To prevent the SSID from being broadcast, select the No radio button.

Chapter 2. Installation and Basic Configuration | 25ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Channel / Frequency From the drop-down list, select the channel you wish to use on your wireless LAN. The wireless channels to use in the United States and Canada are 1 to 11; for Europe and Australia, 1 to 13. The default setting is Auto.Note: It should not be necessary to change the wireless channel unless you experience interference (indicated by lost connections or slow data transfers). Should this happen, you might want to experiment with different channels to see which is the best. For more information, see the guidelines following this table.11ng mode only Note: For most networks, the default settings will work fine.MCS Index / Data Rate From the drop-down list, select a Modulation and Coding Scheme (MCS) index and transmit data rate for the wireless network. The default setting is Best. For a list of all options that you can select from in 11ng mode, see Factory Default Settings in Appendix A.Channel Width From the drop-down list, select a channel width. The options are Dynamic 20/40 MHz, 20 MHz, or 40 MHz. A wider channel improves the performance, but some legacy devices can operate only in either 20 MHz or 40 MHz.Ext Protection Spacing When you select a channel width of Dynamic 20/40 MHz or 40 MHz, you also need to select protection spacing for the extension channel from the Ext Protection Spacing drop-down list. In addition to the default value Auto, you can also select a value of 20 or 25.11ng mode only (continued) Ext Channel Offset When you select a channel width of Dynamic 20/40 MHz or 40 MHz, you also need to select the offset for the extension channel from the Ext Channel Offset drop-down list. In addition to the default value Auto, you can also select Upper or Lower.Guard Interval From the drop-down list, select the guard interval to protect transmissions from interference. In addition to the default value Auto, you can also select Long - 800 ns. Some legacy devices can operate only with a long guard interval.11b and 11bg modes only Data Rate From the drop-down list, select the transmit data rate of the wireless network. The default setting is Best. For a list of all options that you can select from in 11b mode and 11bg mode, see Factory Default Settings in Appendix A.Output Power From the drop-down list, select the transmission power of the wireless access point. The default is Full.Note: Increasing the power improves performance, but if two or more wireless access points are operating in the same area, on the same channel, it can cause interference.Note: Make sure that you comply with the regulatory requirements for total radio frequency (RF) output power in your country.Channel Bonding This drop-down list lets you to specify channels to bond. The available options are 20 MHz, 20/40 MHz, and 40 MHz.Table 6. Basic Wireless Settings (Continued)Field Descriptions

26 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. If you have changed the wireless mode and selected the Turn Radio On check box, a popup window appears: click OK to confirm your change.4. Click Apply to save your settings.Configuring 802.11a/na Wireless SettingsTo configure the 802.11a/na wireless settings:1. Select Configuration > Wireless > Basic > Wireless Settings. The basic Wireless Settings screen displays.2. Specify the fields as explained the following table:Table 7. Basic Wireless Settings Field DescriptionsWireless Mode Select the wireless operating mode that you want to use by selecting one of the following radio buttons:• 11a. 802.11a wireless stations only.• 11na. Both 802.11n and 802.11a wireless stations can be used. This is the default setting.Turn Radio On The radio is enabled by default. To turn off the radio, clear the Turn Radio On check box. Doing so disables access through the wireless access point, which can be helpful for configuration, network tuning, or troubleshooting activities.Wireless Network Name (SSID) Enter a 32-character (maximum) service set identifier (SSID); the characters are case-sensitive. The default is NETGEAR_11a. The SSID assigned to a wireless device needs to match the wireless access point’s SSID for the wireless device to communicate with the wireless access point. If the SSIDs do not match, you will not get a wireless connection to the wireless access point. Scheduler Status This is a nonconfigurable field that show the status of the wireless scheduler. For more information, see Schedule the Wireless Radio on page 52.Broadcast Wireless Network Name (SSID) Select the Yes radio button to enable the wireless access point to broadcasts its SSID, allowing wireless stations that have a null (blank) SSID to adopt the wireless access point’s SSID. Yes is the default setting. To prevent the SSID from being broadcast, select the No radio button.Channel / Frequency From the drop-down list, select the channel you wish to use on your wireless LAN. The wireless channels to use in the United States and Canada are 1 to 11; for Europe and Australia, 1 to 13. The default setting is Auto.Note: It should not be necessary to change the wireless channel unless you experience interference (indicated by lost connections or slow data transfers). Should this happen, you might want to experiment with different channels to see which is the best. For more information, see the guidelines following this table.

Chapter 2. Installation and Basic Configuration | 27ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. If you have changed the wireless mode and selected the Turn Radio On check box, a popup window appears: click OK to confirm your change.4. Click Apply to save your settings.11na mode onlyNote: For most networks, the default settings will work fine.MCS Index / Data Rate From the drop-down list, select a Modulation and Coding Scheme (MCS) index and transmit data rate for the wireless network. The default setting is Best. For a list of all options that you can select from in 11ng mode, see Factory Default Settings in Appendix A.Channel Width From the drop-down list, select a channel width. The options are Dynamic 20/40 MHz, 20 MHz, or 40 MHz. A wider channel improves the performance, but some legacy devices can operate only in either 20 MHz or 40 MHz.Ext Protection Spacing When you select a channel width of Dynamic 20/40 MHz or 40 MHz, you also need to select protection spacing for the extension channel from the Ext Protection Spacing drop-down list. In addition to the default value Auto, you can also select a value of 20 or 25.Ext Channel Offset When you select a channel width of Dynamic 20/40 MHz or 40 MHz, you also need to select the offset for the extension channel from the Ext Channel Offset drop-down list. In addition to the default value Auto, you can also select Upper or Lower.Guard Interval From the drop-down list, select the guard interval to protect transmissions from interference. In addition to the default value Auto, you can also select Long - 800 ns. Some legacy devices can operate only with a long guard interval.11b and 11bg modes only Data Rate From the drop-down list, select the transmit data rate of the wireless network. The default setting is Best. For a list of all options that you can select from in 11b mode and 11bg mode, see Factory Default Settings in Appendix A.Output Power From the drop-down list, select the transmission power of the wireless access point. The default is Full.Note: Increasing the power improves performance, but if two or more wireless access points are operating in the same area, on the same channel, it can cause interference.Note: Make sure that you comply with the regulatory requirements for total radio frequency (RF) output power in your country.Channel Bonding This drop-down list lets you to specify channels to bond. The available options are 20 MHz, 20/40 MHz, and 40 MHz.Table 7. Basic Wireless Settings (Continued)Field Descriptions

28 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Operating Frequency (Channel) GuidelinesYou should not need to change the operating frequency (channel) unless you notice interference problems, or are setting up the wireless access point near another wireless access point. Observe the following guidelines:• Wireless access points use a fixed channel. You can select a channel that provides the least interference and best performance. In the United States and Canada, 11 channels are available.• If you are using multiple wireless access points, it is better if adjacent wireless access points use different channels to reduce interference. The recommended channel spacing between adjacent wireless access points is 5 channels (for example, use channels 1 and 6, or 6 and 11).• In infrastructure mode, wireless stations normally scan all channels, looking for a wireless access point. If more than one wireless access point can be used, the one with the strongest signal is used. This can happen only when the wireless access points use the same SSID. The WNDAP360 wireless access point functions in infrastructure mode by default.Note: For information about how to configure advanced wireless settings, see Configure Advanced Wireless Settings on page 79.Test Basic Wireless ConnectivityAfter you have configured the wireless access point as explained in the previous sections, test your computers for wireless connectivity before you position and mount the wireless access point at its permanent position.To test for wireless connectivity:1. Configure the 802.11b/g/n and 802.11a/n wireless adapters of your computers so that they all have the same SSID and channel that you have configured on the wireless access point.2. Verify that your computers have a wireless link to the wireless access point, and if you have enabled the DHCP server on the wireless access point, verify that your computers are able to obtain an IP address through DHCP from the wireless access point.3. Verify network connectivity by using a browser such as Internet Explorer 6.0 or later or Mozilla Firefox 1.5 or later to browse the Internet, or check for file and printer access on your network.Note: If you have trouble connecting to the wireless access point, see Chapter 6, Troubleshooting.

Chapter 2. Installation and Basic Configuration | 29ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual WARNING!Before you deploy the wireless access point in your network, set up wireless security and other wireless features as described in Chapter 3, Wireless Configuration and Security.In addition to wireless security and other wireless features, before you deploy the wireless access point in your network, configure any additional features as described in Chapter 4, Management and Chapter 5, Advanced Configuration.After you have completed the configuration of the wireless access point, you can reconfigure the computer that you used for this process back to its original TCP/IP settings.Mount the Wireless Access PointThis section includes the following subsections:• Ceiling Installation on this page• Wall Installation on page 31• Desk Installation on page 34Ceiling InstallationTo install the wireless access point using the ceiling installation kit:1. Verify the package content of the ceiling installation kit.2. Detach the mounting plate from the wireless access point.Mounting plateClamp with screws

30 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. Attach the clamp to the ceiling rail.4. Attach the mounting plate to the clamp.5. Connect the cables to the wireless access point.

Chapter 2. Installation and Basic Configuration | 31ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 6. Attach the wireless access point to the mounting plate.7. Attach the cover to the wireless access point.Wall InstallationTo install the wireless access point using the wall installation kit:1. Verify the package content of the wall installation kit.

32 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 2. Detach the mounting plate from the wireless access point.3. Attach the mounting plate to the wall.4. Connect the cables to the wireless access point.Mounting plateScrews andwall supports

Chapter 2. Installation and Basic Configuration | 33ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 5. Attach the wireless access point to the mounting plate.6. Attach the cover to the wireless access point.

34 | Chapter 2. Installation and Basic Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Desk InstallationTo install the wireless access point on a desk, attach the rubber feet to the holes in the bottom of the wireless access point.Rubber feet

Chapter 3. Wireless Configuration and Security | 3533. Wireless Configuration and SecurityThis chapter describes how to configure the wireless features of your ProSafe Dual Band Wireless-N Access Point WNDAP360. The chapter includes the following sections:• Wireless Data Security Options on this page• Security Profiles on page 37• Configure RADIUS Server Settings on page 49• Restrict Wireless Access by MAC Address on page 51• Schedule the Wireless Radio on page 52• Configure Basic Wireless Quality of Service on page 53Before you set up wireless security and additional wireless features that are described in this chapter, connect the wireless access point, get the Internet connection working, and configure the 802.11b , 11bg, or 11ng wireless settings and the 802.11a or 11na wireless settings as described in Chapter 2, Installation and Basic Configuration. The wireless access point should work with an Ethernet LAN connection, and wireless connectivity should have been verified before you set up wireless security and additional wireless features. In planning your wireless network, consider the level of security required.WARNING!If you are configuring the wireless access point from a wireless computer and you change the wireless access point’s SSID, channel, or wireless security settings, you will lose your wireless connection when you click Apply. You then need to change the wireless settings of your computer to match the wireless access point’s new settings.Wireless Data Security OptionsIndoors, computers can connect over 802.11n wireless networks at a maximum range of 300 feet. Typically, a wireless access point inside a building works best with devices within a 100 foot radius. Such distances can allow for others outside your immediate area to access your network.

36 | Chapter 3. Wireless Configuration and Security ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Unlike wired network data, your wireless data transmissions can extend beyond your walls and can be received by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The wireless access point provides highly effective security features that are covered in detail in this chapter. Deploy the security features appropriate to your needs.Figure 11. There are several ways you can enhance the security of your wireless network:• Use multiple BSSIDs combined with VLANs. You can configure combinations of VLANS and BSSIDs with stronger or less restrictive access security according to your requirements. For example, visitors could be given wireless Internet access but be excluded from any access to your internal network. For information about how to configure BSSIDs, see Configure and Enable Security Profiles on page 40.• Restrict access based by MAC address. You can allow only trusted PCs to connect so that unknown PCs cannot wirelessly connect to the wireless access point. Restricting access by MAC address adds an obstacle against unwanted access to your network, but the data broadcast over the wireless link is fully exposed. For information about how to restrict access by MAC address, see Restrict Wireless Access by MAC Address on page 51.• Turn off the broadcast of the wireless network name (SSID). If you disable broadcast of the SSID, only devices that have the correct SSID can connect. This nullifies the wireless network discovery feature of some products, such as Windows XP, but the data is still exposed. For information about how to turn of broadcast of the SSID, see Configure and Enable Security Profiles on page 40.• WEP. Wired Equivalent Privacy (WEP) data encryption provides data security. WEP shared key authentication and WEP data encryption block all but the most determined eavesdropper. This data encryption mode has been superseded by WPA-PSK and WPA2-PSK. For information about how to configure WEP, see Configure and Enable Security Profiles on page 40 and Configure an Open System with WEP or Shared Key with WEP on page 44.• Legacy 802.1X. Legacy 80.1X uses RADIUS-based 802.1x authentication but no data encryption.

Chapter 3. Wireless Configuration and Security | 39ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual _________________________________________________________________________Store this information in a safe place:• SSID: The service set identification (SSID) identifies the wireless local area network. You can customize it by using up to 32 alphanumeric characters. Write your SSID on the line. SSID: ___________________________________ The SSID in the wireless access point is the SSID you configure in the wireless adapter card. All wireless nodes in the same network need to be configured with the same SSID.• WEP Key Size, Key Format Passphrase, and Authentication Choose the key size by circling one: 64, 128, or 152 bits. Choose the key format by circling one: ASCII or HEX. Choose the authentication type by circling one: Open or Shared.Passphrase: ___________________________________ Note: If you select shared key, the other devices in the network will not connect unless they are set to shared key and have the same keys in the same positions as those in the wireless access point.• WPA-PSK (Pre-Shared Key) and WPA2-PSK Record the WPA-PSK passphrase:WPA-PSK Passphrase: ________________________________Record the WPA2-PSK passphrase:WPA2-PSK Passphrase: ________________________________• WPA RADIUS Settings For WPA, record the following settings for the primary and secondary RADIUS servers:Server Name/IP Address: Primary ________________ Secondary _________________ Port: ___________________________________ Shared Secret: ___________________________________ • WPA2 RADIUS Settings For WPA2, record the following settings for the primary and secondary RADIUS servers:Server Name/IP Address: Primary ________________ Secondary _________________ Port: ___________________________________ Shared Secret: ___________________________________ _________________________________________________________________________

Chapter 3. Wireless Configuration and Security | 45ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 13. • Shared Key with WEPShared key provides pre-shared WEP key encryption without RADIUS authentication. The security level of static WEP is not very strong. When you select Shared Key from the Network Authentication drop-down list, the screen expands to display the WEP fields:Figure 14. Table 11. WEP Encryption Settings Field DescriptionsData Encryption Select the encryption key size from the drop-down list:• 64-bit WEP. Standard WEP encryption, using 40/64-bit encryption.• 128-bit WEP. Standard WEP encryption, using 104/128-bit encryption.• 152-bit WEP. Proprietary WEP encryption mode, using 128+24 bits encryption. This mode functions only with other wireless station that support this mode.Passphrase Enter a passphrase. The passphrase length needs to be between 8 and 63 characters (inclusive). The secret passphrase allows you to automatically generate the keys by clicking Generate Keys. The default passphrase is sharedsecret.You can display the actual passphrase by selecting the Show Passphrase in Clear Text radio button.

46 | Chapter 3. Wireless Configuration and Security ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Configure Legacy 802.1XTo use legacy 802.1X security, you need to define RADIUS server settings. For information about RADIUS servers, see Configure RADIUS Server Settings on page 49.When you select Legacy 802.1X from the Network Authentication drop-down list, the Data Encryption drop-down list becomes nonoperational (it shows None only). You need to define the RADIUS servers only to use legacy 802.1X security.Figure 15. Configure WPA with RADIUS, WPA2 with RADIUS, and WPA & WPA2 with RADIUSWPA, WPA2, and WPA & WPA2 security requires RADIUS-based 802.1x authentication, so you also need to define RADIUS server settings. For information about RADIUS servers, see Configure RADIUS Server Settings on page 49.The selections that are available from the Data Encryption drop-down list depend on the type of WPA authentication that you select from the Network Authentication drop-down list and are shown in the following table.• WPA with RADIUSFigure 16. Encryption Key (Key1–Key4) Either manually enter a key or allow the key to be automatically generated by clicking Generate Key.• For ASCII format, depending on the key size selected, the manually entered encryption key needs to have a length of 5 (64-bit WEP), 13 (128-bit WEP), or 16 (152-bit WEP) characters.• For HEX format, depending on the key size selected, the manually entered or automatically generated encryption key needs to have a length of 10 (64-bit WEP), 26 (128-bit WEP), or 32 (152-bit WEP) characters.Note: Wireless stations need to use the key to access the wireless access point.Note: Not all wireless adapters support passphrase key generation.Show Passphrase in Clear Text Select the Yes radio button to display the actual passphrase in the Passphrase field. The default setting is No.Table 11. WEP Encryption Settings (Continued)Field Descriptions

Chapter 3. Wireless Configuration and Security | 47ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual • WPA2 with RADIUSFigure 17. • WPA & WPA2 with RADIUSFigure 18. Configure WPA-PSK, WPA2-PSK, and WPA-PSK & WPA2-PSKWPA-PSK, WPA-PSK, and WPA-PSK & WPA2-PSK authentication use a pre-shared key (PSK) and do not require authentication from a RADIUS server. Table 12. WPA with RADIUS, WPA2 with RADIUS, and WPA & WPA2 with RADIUS Settings Field DescriptionsTKIP Temporal Key Integrity Protocol (TKIP) is the standard encryption method used with WPA. You can also use TKIP with WPA2.Note: TKIP provides only legacy (slower) rates of operation. NETGEAR recommends WPA2 authentication with AES encryption if you want to use the 11n rates and speed. AES Advanced Encryption Standard (AES) is the standard encryption method used with WPA2.Note: Although some wireless clients might support AES with WPA, the WNDAP360 wireless access point does not support WPA with AES.TKIP + AES The TKIP + AES encryption method is supported both for WPA and WPA2. Broadcast packets use TKIP. For unicast (point-to-point) transmissions, WPA clients use TKIP, and WPA2 clients use AES. For the WPA & WPA2 mixed mode, TKIP + AES is the only supported data encryption method.

48 | Chapter 3. Wireless Configuration and Security ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual The selections that are available from the Data Encryption drop-down list depend on the type of WPA-PSK authentication that you select from the Network Authentication drop-down list and are shown in the following table.• WPA-PSKFigure 19. • WPA2-PSKFigure 20. • WPA-PSK & WPA2-PSKFigure 21.

Chapter 3. Wireless Configuration and Security | 49ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Configure RADIUS Server SettingsFor authentication, accounting, or both authentication and accounting using RADIUS, you need to configure primary servers and optional secondary servers. These RADIUS server settings can apply to all devices that are connected to the wireless access point.To configure the RADIUS server settings:1. Select Configuration > Security > Advanced > Radius Server Settings. The Radius Server Settings screen displays. (The following figure shows some examples.)Table 13. WPA-PSK, WPA2-PSK, and WPA-PSK & WPA2-PSK Settings Field DescriptionsData Encryption TKIP Temporal Key Integrity Protocol (TKIP) is the standard encryption method used with WPA. You can also use TKIP with WPA2.Note: TKIP provides only legacy (slower) rates of operation. NETGEAR recommends WPA2 authentication with AES encryption if you want to use the 11n rates and speed. AES Advanced Encryption Standard (AES) is the standard encryption method used with WPA2.Note: Although some wireless clients might support AES with WPA, the WNDAP360 wireless access point does not support WPA with AES.TKIP + AES TKIP + AES supports both WPA and WPA2. Broadcast packets use TKIP. For unicast (point-to-point) transmissions, WPA clients use TKIP, and WPA2 clients use AES.For the WPA & WPA2 mixed mode, TKIP + AES is the only supported data encryption method.Passphrase Enter a passphrase. The passphrase length needs to be between 8 and 63 characters (inclusive). The default passphrase is sharedsecret.You can display the actual passphrase by selecting the Show Passphrase in Clear Text radio button. Show Passphrase in Clear Text Select the Yes radio button to display the actual passphrase in the Passphrase field. The default setting is No.

50 | Chapter 3. Wireless Configuration and Security ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 22. 2. Specify the settings as explained in the following table:Table 14. RADIUS Server Settings Field DescriptionsRADIUS Server SettingsPrimary Authentication Server IP Address Enter the IP address of the primary RADIUS server for authentication.Authentication Port Enter the UDP port number of the wireless access point that is used to access the primary RADIUS server for authentication. The default port number is 1812. Secret Enter the shared key that is used between the wireless access point and the primary RADIUS server during authentication.Secondary Authentication Server IP Address Enter the IP address of the secondary RADIUS server for authentication. The secondary RADIUS server is used when the primary RADIUS server is not available.Authentication Port Enter the UDP port number of the wireless access point that is used to access the secondary RADIUS server for authentication. The default port number is 1812. Secret Enter the shared key that is used between the wireless access point and the secondary RADIUS server during authentication.Primary Accounting Server IP Address Enter the IP address of the primary RADIUS server for accounting.Authentication Port Enter the UDP port number of the wireless access point that is used to access the primary RADIUS server for accounting. The default port number is 1813. Secret Enter the shared key that is used between the wireless access point and the primary RADIUS server during the accounting process.

Chapter 3. Wireless Configuration and Security | 51ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. Click Apply to save your settings.Restrict Wireless Access by MAC AddressFor increased security, you can restrict access to an SSID by allowing access to only specific computers or wireless stations based on their MAC addresses. You can restrict access to only trusted computers so that unknown computers cannot wirelessly connect to the wireless access point. MAC address filtering adds an obstacle against unwanted access to your network, but the data broadcast over the wireless link is fully exposed.Note: For wireless adapters, you can usually find the MAC address printed on the wireless adapter.To restrict access based on MAC addresses:1. Select Configuration > Security > Advanced > MAC Authentication. The MAC Authentication screen displays.2. Select the Turn Access Control On check box to enable the access control feature.3. From the Select Access Control Database drop-down list, select one of the following database options:• Local MAC Address Database. The wireless access point uses the local MAC address database for access control. This is the default setting.• Remote MAC Address Database. The wireless access point uses the MAC address database on an external RADIUS server on the LAN for access control. If you select Secondary Accounting Server IP Address Enter the IP address of the secondary RADIUS server for accounting. The secondary RADIUS server is used when the primary RADIUS server is not available.Authentication Port Enter the UDP port number of the wireless access point that is used to access the secondary RADIUS server for accounting. The default port number is 1813. Secret Enter the shared key that is used between the wireless access point and the secondary RADIUS server during the accounting process.Authentication SettingsReauthentication Time (Seconds) The interval in seconds after which the supplicant is reauthenticated with the RADIUS server. The default interval is 3600 seconds (1 hour). Enter 0 to disable reauthentication.Update Global Key Every (Seconds) Select the check box to allow the global key update, and enter the interval in seconds. The check box is selected by default, and the default interval is 1800 seconds (30 minutes). Clear the check box to prevent the global key update.Table 14. RADIUS Server Settings (Continued)Field Descriptions

52 | Chapter 3. Wireless Configuration and Security ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual this database, you first need to configure the RADIUS server settings (see Configure RADIUS Server Settings on page 49).4. Click Refresh to refresh the Available Wireless Stations table. The wireless access point places the MAC addresses of the attached wireless stations in this table.5. Populate the Trusted Wireless Stations table by one of the following methods:• Select MAC addresses from the Available Wireless Stations table:a. Select individual check boxes for MAC addresses, or select all MAC addresses by selecting the check box in the heading.b. Click Move to transfer the MAC addresses from the Available Wireless Stations table to the Trusted Wireless Stations table.• Enter MAC addresses manually:a. Enter a MAC address directly in the Trusted Wireless Stations table.b. Click Add.To delete a MAC address from the Trusted Wireless Stations table, select individual check boxes for MAC addresses, or select all MAC addresses by selecting the check box in the heading, and then click Delete.6. Click Apply to save your settings.Now, only devices in the Trusted Wireless Stations table are allowed to wirelessly connect to the wireless access point.WARNING!When configuring the wireless access point from a wireless computer whose MAC address is not in the access control list, you will lose your wireless connection when you click Apply. You then need to access the wireless access point from a wired computer or from a wireless computer which is on the access control list to make any further changes.Schedule the Wireless RadioScheduled Wireless On/Off is a green feature that allows you to turn off the wireless radio during scheduled vacations, office shutdowns, on evenings, or on weekends.To schedule the radio:1. Select Configuration > Wireless > Basic > Scheduled Wireless ON-OFF. The Scheduled Wireless ON-OFF screen displays.

Chapter 3. Wireless Configuration and Security | 53ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 2. Specify the settings as explained in the following table:3. Click Apply to save your settings.Configure Basic Wireless Quality of ServiceWi-Fi Multimedia (WMM) is a subset of the 802.11e standard. WMM allows wireless traffic to have a range of priorities, depending on the type of data. Time-dependent information, such as video or audio, has a higher priority than normal traffic. For WMM to function correctly, wireless clients also need to support WMM.By enabling WMM, you allow Quality of Service (QoS) control for upstream traffic flowing from a wireless station to the wireless access point and for downstream traffic flowing from the wireless access point to a wireless station.WMM defines the following four queues in decreasing order of priority:• Voice. The highest priority queue with minimum delay, which makes it ideal for applications like VoIP and streaming media.• Video. The second highest priority queue with low delay is given to this queue. Video applications are routed to this queue.• Best Effort. The medium priority queue with medium delay is given to this queue. Most standard IP application use this queue.• Background. Low priority queue with high throughput. Applications, such as FTP, that are not time-sensitive but require high throughput can use this queue.The WMM Powersave feature saves power for battery-powered equipment by increasing the efficiency and flexibility of data transmission.Note: For information about how to configure advanced wireless QoS, that is, to configure specific Enhanced Distributed Channel Access (EDCA) settings, see Configure Advanced QoS Settings on page 81.Table 15. Schedule Wireless Radio On/Off Settings Field DescriptionSchedule Wireless on-off Select the On radio button to enable the timer. By default, the Off radio button is selected.Radio off schedule Select check boxes to specify the days when you want to schedule the radio to be turned off. By default, Saturday and Sunday are selected.Radio ON Time Fill in the time that you want the radio to be turned back on. Use 24-hour time format.Radio OFF Time Fill in the time that you want the radio to be turned off. Use 24-hour time format.

54 | Chapter 3. Wireless Configuration and Security ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual To configure basic wireless QoS:1. Select Configuration > Wireless > Basic > QoS Settings. The basic QoS Settings screen displays.2. Enable or disable the WMM features:• Enable Wi-Fi Multimedia (WMM). To enable this feature, select the Enable radio button, which is the default setting. Select the Disable button to disable the feature.• WMM Powersave. To enable this feature, select the Enable radio button, which is the default setting. Select the Disable button to disable the feature.3. Click Apply to save your settings.

Chapter 4. Management | 5544. ManagementThis chapter describes how to use the management and monitoring features of your ProSafe Dual Band Wireless-N Access Point WNDAP360. This chapter includes the following sections:• Enable Remote Management on this page• Upgrade the Wireless Access Point Software on page 58• Manage the Configuration File or Reset to Factory Defaults on page 61• Change the Administrator Password on page 65• Enable the Syslog Server on page 66• Monitor the Wireless Access Point on page 67• Enable Rogue AP Detection and Monitor Access Points on page 73Enable Remote ManagementBoth SNMP and the remote console Secure Shell (SSH) are enabled by default, which allows for remote management of the wireless access point from a client running SNMP management software, as well as from a secure shell (SSH) client. The Telnet console is disabled by default.SNMP ManagementTo set up an SNMP management interface:1. Select Maintenance > Remote Management > SNMP. The SNMP screen displays:

56 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 23. 2. Specify the settings as explained in the following table:3. Click Apply to save your settings.Table 16. SNMP Settings Field DescriptionSNMP Select the Enable radio button to allow the SNMP network management software, such as HP OpenView, to manage the wireless access point through SNMPv1/v2 protocol. By default, the Disable radio button is selected.Read-Only Community Name Enter the community string to allow the SNMP manager to read the wireless access point’s Management Information Base (MIB) objects. The default is public.Read-Write Community Name Enter the community string to allow the SNMP manager to read and write the wireless access point’s MIB objects. The default is private.Trap Community Name The community string to allow the SNMP manager to send traps. The default is trap.IP Address to Receive Traps The IP address of the SNMP manager to receive traps sent from the wireless access point. Trap Port The port number of the SNMP manager to receive traps sent from the wireless access point. The default is 162.

Chapter 4. Management | 57ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Secure Shell and Telnet ManagementTo configure remote console features:1. Select Maintenance > Remote Management > Remote Console. The Remote Console screen displays:Figure 24. 2. Enable or disable the remote console features:• Secure Shell (SSH). To enable this feature, select the Enable radio button, which is the default setting. Select the Disable button to disable the feature.• Telnet. To enable this feature, select the Enable radio button. Select the Disable button to disable the feature, which is the default setting.3. Click Apply to save your settings.To manage the wireless access point over a Telnet connection:1. Connect an Ethernet cable to the console port of the wireless access point.2. Connect the other end of the cable to a VT100/ANSI terminal or a workstation.If you attach a PC, Apple Macintosh, or UNIX workstation, start a secure terminal-emulation program, and configure the terminal-emulation program to use the following settings:• Baud rate: 9600 bps• Data bits: 8• Parity: none• Stop bit: 1• Flow control: none

58 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. Start a secure Telnet session from the terminal or workstation to the wireless access point. A screen similar to the following should display:Figure 25. 4. Enter the login name and password (admin and password are the defaults). After successful login, the > prompt should appear preceded by the name of the wireless access point. In this example, the prompt is netgear334408. 5. Enter the CLI commands that you want to use. You can enter show configuration to display the available CLI commands. The CLI commands are also listed in Appendix B, Command-Line Reference.Upgrade the Wireless Access Point Software The software of the wireless access point is stored in flash memory and can be upgraded as NETGEAR releases new software. You can download upgrade files from the NETGEAR website. If the upgrade file is compressed (.zip file), you first need to extract the image (.rmt) file before sending it to the wireless access point. You can send the upgrade file using your browser. There are two methods to perform a software upgrade that are described in the following sections:• Web Browser Upgrade Procedure on page 59• TFTP Server Upgrade Procedure on page 60Note: The Web browser that you use to upload new firmware into the wireless access point needs to support HTTP uploads. Use a browser such as Microsoft Internet Explorer 6.0 or later or Mozilla 1.5 or later.

Chapter 4. Management | 59ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Note: You cannot perform the software upgrade from a computer that is connected to the wireless access point over a wireless link. You need to use a computer that is connected to the wireless access point over an Ethernet cable.WARNING!When uploading software to the wireless access point, do not interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, the upload might fail, corrupt the software, and render the wireless access point completely inoperable.IMPORTANT:In some cases, such as a major upgrade, you might need to erase the configuration and manually reconfigure your wireless access point after upgrading it. See the release notes included with the software to find out if you need to reconfigure the wireless access point.Web Browser Upgrade ProcedureTo use a Web browser to upgrade the wireless access point firmware:1. Download the new software file from the NETGEAR website and save it to your hard disk.2. If necessary, unzip the new software file.3. If available, read the release notes before upgrading the software.4. Select Maintenance > Upgrade > Firmware Upgrade. The Firmware Upgrade screen displays:

60 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 26. 5. Click Browse and locate the image (.zip) upgrade file.6. Click Apply to initiate the upgrade process.During the upgrade process, the wireless access point automatically restarts. The upgrade process typically takes several minutes. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point.7. Verify that the new software file has been installed by selecting Monitoring > System. The System screen displays (see Figure 34 on page 67). The firmware version is shown in the Access Point Information section of the screen.TFTP Server Upgrade ProcedureTo use this method, you need to have a TFTP server set up.To use a TFTP server to upgrade the wireless access point firmware:1. Download the new software file from the NETGEAR website and save it to your hard disk.2. Place the software file in your TFTP server location. (You do not need to unzip the file.)3. If available, read the release notes before upgrading the software.4. Select Maintenance > Upgrade > Firmware Upgrade TFTP. The Firmware Upgrade TFTP screen displays:

Chapter 4. Management | 61ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 27. 5. Specify the following information:• Firmware File Name. The name of the unzipped software file.• TFTP Server IP. The IP address of your TFTP server.6. Click Apply to initiate the upgrade process.During the upgrade process, the wireless access point automatically restarts. The upgrade process typically takes several minutes. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point.7. Verify that the new software file has been installed by selecting Monitoring > System. The System screen displays (see Figure 34 on page 67). The firmware version is shown in the Access Point Information section of the screen.Manage the Configuration File or Reset to Factory DefaultsThe wireless access point settings are stored in the configuration file. You can save this file (back it up) to a computer, restore it from a computer, or reset it to factory default settings.Save the ConfigurationTo save your settings:1. Select Maintenance > Upgrade > Backup Settings. The Backup Settings screen displays (see the following figure).2. Click Backup. Your browser extracts the configuration file (the file name is config) from the wireless access point and prompts you for a location on your computer to store the file. 3. Follow the instructions of your browser to save the file.

62 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 28. Restore the ConfigurationIMPORTANT:During the restoration process, do not try to go online, turn off the wireless access point, shut down the computer, or do anything else to the wireless access point until it finishes restarting!To restore your settings from a saved configuration file:1. Select Maintenance > Upgrade > Restore Settings. The Restore Settings screen displays:Figure 29. 2. Click Browse and locate the saved configuration file (the file name is config).3. Click Apply to initiate the restoration process. During the restoration process, the wireless access point automatically restarts. The restoration process typically takes about 1 minute. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point.

Chapter 4. Management | 63ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Restore the Wireless Access Point to the Factory Default SettingsYou can restore the wireless access point to the factory default settings by two methods that are described in the following sections:• Use the Web Management Interface to Restore Factory Default Settings on this page• Use the Reset Button to Restore Factory Default Settings on page 64Note: After you have restored the factory default settings on the wireless access point: * All custom configurations will be lost. * The login password will be password. * The default LAN IP address will be 192.168.0.100. * The DHCP client will be disabled. * The Access Point Name field will be reset to the name printed on the label on the bottom of the unit.Use the Web Management Interface to Restore Factory Default SettingsIMPORTANT:During the restoration process, do not try to go online, turn off the wireless access point, shut down the computer, or do anything else to the wireless access point until it finishes restarting!To restore the factory default settings using the Web Management Interface:1. Select Maintenance > Reset > Restore Defaults. The Restore Defaults screen displays (see the following figure).2. Select the Yes radio button. (By default, the No radio button is selected.)3. Click Apply to reset the wireless access point to the factory default settings. During the restoration process, the wireless access point automatically restarts. The restoration process typically takes about 1 minute. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point.

64 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 30. Use the Reset Button to Restore Factory Default SettingsTo restore the factory default settings when you do not know the login user name, login password, or IP address, you need to use the Reset button on the rear panel of the wireless access point (see Figure 2 on page 12).To restore the factory default settings using the Reset button:1. Using a sharp object, press and hold the Reset button for about 5 seconds (until the Test LED blinks rapidly) to reset the wireless access point to factory defaults settings.Note: Pressing the Reset button for a shorter period of time simply causes the wireless access point to reboot.2. Release the Reset button.During the restoration process, the wireless access point automatically restarts. The restoration process typically takes about 1 minute. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point.Reboot the Wireless Access Point without Restoring the Default ConfigurationIf you do not have physical access to the wireless access point to switch it off and on again, you can use the software to reboot the wireless access point.To reboot the wireless access point:1. Select Maintenance > Reset > Reboot AP. The Reboot AP screen displays:

Chapter 4. Management | 65ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 31. 2. Select the Yes radio button. (By default, the No radio button is selected.)3. Click Apply to reboot the wireless access point.The reboot process typically takes about 1 minute. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point.Change the Administrator PasswordThe default password is password. You should change this password to a more secure password. You cannot change the administrator login name (admin).The ideal password should contain no dictionary words from any language, and should be a mixture of letters (both uppercase and lowercase), numbers, and symbols. Your password can be up to 30 characters.To change the administrator password:1. Select Maintenance > Password > Change Password. The Change Password screen displays:Figure 32. 2. Take one of the following actions:

66 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual • Enter a new password twice: once in the New Password field and again in the Repeat New Password field.• Next to Restore Default Password, select the Yes radio button to restore the default password. By default, the No radio button is selected.3. Click Apply to save your settings.If you have restored the default password, the login password will be password. If you have configured a new password, write it down in a secure place.Enable the Syslog ServerThe Syslog screen allows you to enable the syslog option if you have a syslog server on your LAN. If syslog is enabled, the wireless access point sends its syslog files to the syslog server.To enable a syslog server:1. Select Configuration > System > Advanced > Syslog. The Syslog screen displays:Figure 33. Specify the settings as explained in the following table:2. . Click Apply to save your settings.Table 17. Syslog Settings Field DescriptionEnable Syslog Select the check box to enable the syslog option. By default, the syslog option is disabled.Syslog Server IP Address Enter the IP address of the syslog server to which the wireless access point sends the syslog files.Port Number Enter the port number that is configured on the syslog server. The default port number is 514.

Chapter 4. Management | 67ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Monitor the Wireless Access PointThe wireless access point provides a variety of status and usage information that is discussed in the following sections:• View System Information on page 67• Monitor Wireless Stations on page 69• View the Activity Log on page 71• Traffic Statistics on page 72View System InformationThe System screen provides a summary of the current wireless access point configuration settings, including current IP settings and current wireless settings. This information is read only, so any changes need to be made on other screens.To view the System screen, select Monitoring > System:Figure 34.

68 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual The following table explains the fields of the System screen:Table 18. System Screen Fields Field DescriptionAccess Point InformationAccess Point Name The NetBIOS name. For information about how to change the default name, see Configure Basic General System Settings and Time Settings on page 18.Ethernet MAC Address The MAC address of the wireless access point’s Ethernet port.Wireless MAC Address The MAC address of the wireless access point’s wireless card.Country/Region The country or region for which the wireless access point is licensed for use. For information about how to change the country or region, see Configure Basic General System Settings and Time Settings on page 18.Note: It might not be legal to operate this wireless access point in a country or region other than one of those identified in this field.Firmware Version The version of the firmware that is currently installed.Current Time The current time. For information about how to change the time settings, see Configure Basic General System Settings and Time Settings on page 18.Current IP SettingsFor information about how to change any of these IP settings, see Configure IP Settings and Optional DHCP Server Settings on page 20.IP Address The IP address of the wireless access point.Subnet Mask The subnet mask for the wireless access point.Default Gateway The default gateway for the wireless access point communication.DHCP Client Enabled indicates that the current IP address was obtained from a DHCP server on your LAN network. Disabled indicates a static IP configuration.Current Wireless Settings for 802.11n/gAccess Point Mode The operating mode of the wireless access point. One of the following modes is indicated:• Access Point• Point-to-Point Bridge• Point-to-Point Bridge with Access Point• Multi-Point Bridge with/without client associationFor information about how to change the mode, see Configure Wireless Bridging on page 83.Channel / Frequency The channel the wireless port is using. 11 is the default channel when the setting is Auto. For information about how to change the channel and frequency, see Configure Basic Wireless Settings on page 23.Rogue AP Detection Enabled indicates that rogue AP detection is enabled; Disabled indicates that it is not.

Chapter 4. Management | 69ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Monitor Wireless StationsThe Wireless Stations screen contains the Available Wireless Stations table. This table shows all IP devices that are associated with the wireless access point in the wireless network that is defined by the wireless network name (SSID). The table heading indicates the wireless mode (802.11b, 802.11bg, or 802.11ng).Note: A wireless network can include multiple wireless access points, all using the same network name (SSID). This extends the reach of the wireless network and allows users to roam from one wireless access point to another, providing seamless network connectivity. Under these circumstances, be aware that the Available Wireless Stations table includes only the stations associated with this wireless access point.To view the attached wireless stations, and to view details for a wireless station:1. Select Monitoring > Wireless Stations. The Wireless Stations screen displays:Figure 35. To update the list, click Refresh. If the wireless access point is rebooted, the wireless station data is lost until the wireless access point rediscovers the devices. To force the wireless access point to look for associated devices, click Refresh.For each device, the Available Wireless Stations table shows the MAC address, BSSID, SSID, channel, rate, state, type, AID, mode, and status. For information about these and more fields, see the following table.2. To view details of a wireless station, select the corresponding radio button, and then click Details. The Wireless Stations Details screen displays:

70 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Figure 36. The following table explains the fields of the Wireless Stations Details screen:Table 19. Wireless Stations Details Fields Field DescriptionMAC Address The MAC address of the wireless station.BSSID The BSSID that the wireless station is using.SSID The SSID that the wireless station is using.Channel The channel that the wireless station is using.Rate The transmit data rate in Mbps of the wireless station.State The features that are enabled on the wireless station.Type The authentication and encryption type that the wireless station is using.AID The associated identifier (AID) of the wireless station.Mode The wireless mode in which the wireless station is operating.Status The wireless status of the wireless station (Associated).

Chapter 4. Management | 71ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual View the Activity LogYou can view the wireless access point’s activity log onscreen and save the logs.To display the activity log and save it:1. Select Monitoring > Logs. The Logs screen displays:Figure 37. 2. Click Save As to save the log contents to a file on your computer or to a disk drive.RSSI The received signal strength indicator (RSSI) of the wireless station.Idle Time The time since the last frame was received from the wireless station.Tx Sequence The sequence number of the last frame that was transmitted to the wireless station.Rx Sequence The sequence number of the last frame that was received from the wireless station.Capability The capability summary of the wireless station that was detected during association.Cipher The cipher that is used by the wireless station and that defines the type of encryption.SNR The signal-to-noise ratio (SNR) that indicates how much the signal of the wireless station has been corrupted by noise.Recv. Bytes The number of bytes received on the wireless station since it last started up.Trans. bytes The number of bytes transmitted by the wireless station since it last started up.Assoc. Time Stamp The time when these details of the wireless station were retrieved.IP Address The IP address of the wireless station.Channel Width The channel width at which the wireless station operates.Table 19. Wireless Stations Details Fields (Continued)Field Description

72 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual To update the display on screen, click Refresh; to clear the log content, click Clear.Traffic StatisticsThe Statistics screen displays information for both wired (LAN) and wireless (WLAN) network traffic.To display the Statistics screen, select Monitoring > Statistics:Figure 38. To update the statistics information, click Refresh.The following table explains the fields of the Statistics screen:Table 20. Statistics Fields Field DescriptionWired EthernetPackets The number of packets received and transmitted over the Ethernet connection since the wireless access point was restarted.Bytes The number of bytes received and transmitted over the Ethernet connection since the wireless access point was restarted.

Chapter 4. Management | 73ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Enable Rogue AP Detection and Monitor Access PointsEnable and Configure Rogue AP DetectionThe wireless access point can detect rogue access points and prevent them from connecting to the wireless access point. The wireless access point maintains a list of access points it detects in the area. Initially all detected access points are displayed in the Unknown AP List. You restrict communication to approved access points by adding them to the Known AP List and enabling the rogue AP detection feature.If you enable rogue AP detection, the wireless access point continuously scans the wireless network and collects information about all access point on its channel.To enable and configure rogue AP detection:1. Select Configuration > Security > Advanced > Rogue AP. The Rogue AP screen displays.2. Click Refresh to let the wireless access point discover the access points and populate the Unknown AP List.3. In the Unknown AP List, select individual check boxes for access points, or select all access points by selecting the check box in the column heading.4. Click Move to transfer the access points from the Unknown AP List to the Known AP List.Wireless 802.11b, Wireless 802.11bg, or Wireless 801.11ngThe section heading depends on the configured wireless mode.Unicast Packets The number of unicast packets received and transmitted over the wireless connection since the wireless access point was restarted.Broadcast Packets The number of broadcast packets received and transmitted over the wireless connection since the wireless access point was restarted.Multicast Packets The number of multicast packets received and transmitted over the wireless connection since the wireless access point was restarted.Total Packets The total number of packets received and transmitted over the wireless connection since the wireless access point was restarted.Total Bytes The total number of bytes received and transmitted over the wireless connection since the wireless access point was restarted.Client Association802.11b Radio,802.11bg Radio, or802.11ng RadioThe number of associated clients connected to the radio in the configured wireless mode.Table 20. Statistics Fields (Continued)Field Description

74 | Chapter 4. Management ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 5. Select the Turn Rogue AP Detection On check box to enable rogue AP detection.6. Click Apply to save your settings.To remove APs from the Known AP List and return then to the Unknown AP List:1. In the Known AP List, select individual check boxes for access points, or select all access points by selecting the check box in the column heading.2. Click Delete.To import a file with a precompiled list of access points into the Known AP List: 1. Take one of the following actions:• Select the Replace radio button to let the imported list with access points replace the existing Known AP List.• Select the Merge radio button to add the imported list with access points to the existing Known AP List.2. Click Browse and locate the file that contains the list with access points. This file needs to be a simple text file with one MAC address per line.3. Select the file, and click Open.4. Click Apply to upload the list with access points to the Known AP List.View and Save Access Point ListsThe wireless access point detects nearby APs and wireless stations and maintains them in a list. You can use this list to prevent them from connecting to the wireless access point.To view the Unknown AP List and save it to a file:1. Select Monitoring > Rogue AP > Unknown AP List. The Unknown AP List screen displays.2. Click Refresh to let the wireless access point discover the access points and populate the Unknown AP List.The following table explains the fields of the Unknown AP List screen:Table 21. Unknown AP List FieldsField DescriptionMAC Address The MAC address of the unknown AP.SSID The SSID that the unknown AP is using.Privacy Indicates whether or not security is enabled (1 means enabled; 0 means disabled).Channel The channel that the unknown AP is using.Rate The transmit data rate in Mbps of the unknown the AP.

Chapter 4. Management | 75ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. Click Save to export the list of unknown or known APs to a file. A window opens so you can browse to the location where you want to save the file. The default file name is macList.txt.If you wish, you can now import the saved list into the Known AP List on the Rogue AP screen (see Enable and Configure Rogue AP Detection on page 73).To view the Known AP List and save it to a file:1. Select Monitoring > Rogue AP > Known AP List. The Known AP List screen displays.2. Click Refresh to let the wireless access point discover the access points and populate the Known AP List.The following table explains the fields of the Known AP List screen:3. Click Save to export the list of known access points to a file. A window opens so you can browse to the location where you want to save the file. The default file name is macList.txt.You can now import the saved list into the Known AP List on the Rogue AP screen (see Enable and Configure Rogue AP Detection on page 73).Beacon Int. The interval for each beacon transmission in ms.# of Beacons The number of beacons transmitted by the unknown AP that the wireless access point has detected.Last Beacon The timestamp that indicates the time when the most recent beacon was detected.Table 22. Known AP List FieldsField DescriptionMAC Address The MAC address of the known AP.SSID The SSID that the known AP is using.Channel The channel that the known AP is using.Table 21. Unknown AP List FieldsField Description

Chapter 5. Advanced Configuration | 7655. Advanced ConfigurationThis chapter describes how to configure the advanced features of your ProSafe Dual Band Wireless-N Access Point WNDAP360. The chapter includes the following sections:• Spanning Tree Protocol and 802.1Q VLAN on this page• Hotspot Settings on page 78• Configure Advanced Wireless Settings on page 79• Configure Advanced QoS Settings on page 81• Configure Wireless Bridging on page 83Spanning Tree Protocol and 802.1Q VLANThe advanced General system settings screen allows you to enable the Spanning Tree Protocol (STP) and configure the VLANs.STP provides network traffic optimization in locations where multiple wireless access points are active.The 802.1Q VLAN protocol on the wireless access point logically separates traffic on the same physical network:• Untagged VLAN. When the wireless access point sends frames that are associated with the untagged VLAN from its Ethernet interface, those frames are untagged. When the wireless access point receives untagged frames over its Ethernet interface, those frames are assigned to the untagged VLAN.Note: Select the Untagged VLAN check box only if the hubs and switches on your LAN support the 802.1Q VLAN protocol. Likewise, change the untagged VLAN value only if the hubs and switches on your LAN support the 802.1Q VLAN protocol. Selecting the Untagged VLAN check box or changing the untagged VLAN value will result in a loss of IP connectivity if the hubs and switches on your LAN have not yet been configured with the corresponding VLAN.

Chapter 5. Advanced Configuration | 77ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual • Tagged VLAN. When you clear the Untagged VLAN check box, the wireless access point tags all frames that are sent from its Ethernet interface. Only incoming frames that are tagged with known VLAN IDs are accepted.• Management VLAN. The management VLAN can be active only when the wireless access point functions as a point-to-point or point-to-multipoint bridge (see Configure Wireless Bridging on page 83). The management VLAN is used for managing traffic (Telnet, SNMP, and HTTP) to and from the wireless access point.Frames belonging to the management VLAN are not given any 802.1Q header when they are sent over the trunk. If a port is in a single VLAN, it can be untagged. However, if the port is a member of multiple VLANs, it needs to be tagged.To configure STP and VLANs:1. Select Configuring > System > Advanced > General. The advanced General system settings screen displays:Figure 39. 2. Specify the settings as explained in the following table:Table 23. STP and VLAN Settings Field DescriptionSpanning Tree ProtocolSpanning Tree Protocol Select the Enable radio button to enable STP to prevent path redundancy. By default, the Disable radio button is selected.

78 | Chapter 5. Advanced Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. Click Apply to save your settings.Hotspot SettingsIf the wireless access point functions as a public access point and you want it to capture and redirect all HTTP requests (over TCP, port 80), set up a hotspot server to redirect the requests to the specified URL and manage the clients. For example, you can redirect HTTP requests to a Web server for authentication, timing control, or advertising. A hotel might want all wireless connections to go to its server to start a billing transaction.Note: The redirection occurs only the first time that a wireless client opens a Web browser.To set up a hotspot server:1. Select Configuration > System > Advanced > Hotspot. The Hotspot screen displays:Figure 40. 802.1Q VLANUntagged VLAN Select the Untagged VLAN check box to configure one VLAN as an untagged VLAN. By default, the Untagged VLAN check box is selected.Specify a VLAN ID. The default VLAN ID is 1.Management VLAN Specify an ID for the VLAN from which the wireless access point can be managed. The default VLAN ID is 1. Note: If you configure the VLAN ID as 0 (zero), the wireless access point can be managed over any VLAN, and frames that belong to the management VLAN are not tagged with an 802.1Q header when sent over the trunk.Table 23. STP and VLAN Settings (Continued)Field Description

Chapter 5. Advanced Configuration | 79ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 2. To enable HTTP redirection, select the Enable radio button. By default, the Disable radio button is selected.3. In the Redirect URL field, enter the URL of the Web server to which you wish to redirect HTTP requests.4. Click Apply to save your settings. All HTTP requests are now redirected to the specified URL.Configure Advanced Wireless SettingsYou use the advanced Wireless Settings screen to configure and enable various WLAN settings for 802.11b, 802.11bg, or 802.11ng wireless mode. The active wireless mode is indicated on screen. (For information about hot to change the wireless mode, see Configure Basic Wireless Settings on page 23.) The default WLAN settings normally work well. However, you can use these settings to fine-tune the overall performance of your wireless access point for your environment.To configure advanced wireless settings:1. Select Configuration > Wireless > Advanced > Wireless Settings. The advanced Wireless Settings screen displays. 2. Specify the settings as explained in the following table:Table 24. Advanced Wireless Settings Field DescriptionRTS Threshold (0–2347) Enter the Request to Send (RTS) threshold. The default setting is 2347.If the packet size is equal to or less than the RTS threshold, the wireless access point uses the Carrier Sense Multiple Access with Collision Detection (CSMA/CD) mechanism, and the data frame is transmitted immediately after the silence period.If the packet size is larger than the RTS threshold, the wireless access point uses the CSMA with Collision Avoidance (CSMA/CA) mechanism. In this situation, the transmitting station sends an RTS packet to the receiving station, and waits for the receiving station to return a Clear to Send (CTS) packet before sending the actual packet data.Fragmentation Length (256–2346) Enter the maximum packet size that is used for the fragmentation of data packets. Packets that are larger than the specified fragmentation length are broken up into smaller packets before being transmitted. The fragmentation length needs to be an even number. The default setting is 2346.Beacon Interval (100–1000) Enter the interval between 100 ms and 1000 ms for each beacon transmission, which allows the wireless access point to synchronize the wireless network. The default setting is 100.

80 | Chapter 5. Advanced Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. Click Apply to save your settings. Aggregation Length (1024–65535) Enter the maximum length of Aggregated MAC Protocol Data Unit (AMPDU) packets. Larger aggregation lengths could lead to better network performance. Aggregation is a mechanism used to achieve higher throughput. The default setting is 65535.AMPDU Select the Enable radio button to allow the aggregation of several MAC frames into a single large frame to achieve higher throughput. Enabling Aggregated MAC Protocol Data Unit (AMPDU) could lead to better network performance. By default, the Enable radio button is selected.RIFS Transmission Select the Enable radio button to allow transmission of successive frames at different transmit powers. Enabling Reduced Interframe Space (RIFS) could lead to better network performance. By default, the Disable radio button is selected.DTIM Interval (1–255) Enter the Delivery Traffic Indication Message (DTIM) interval, also referred to as the data beacon rate, which indicates the beacon delivery traffic indication message period in multiples of beacon intervals. This value needs to be between 1 and 255. The default setting is 3.Preamble Type Select one of the following radio buttons to specify the preamble type:• Long. A long transmit preamble might provide a more reliable connection or a slightly longer range. A short transmit preamble gives better performance.• Auto. The Auto settings automatically handles both long and short preambles. The default setting is Auto.Antenna Select one of the following radio buttons to specify the antenna:• Internal. Enables the internal antenna. This is the default setting.• External. Enables an optional external antenna.802.11d Select this check box to enable support for additional regulatory domains that are not in the current standard; support includes the addition of a country information element to beacons, probe requests, and probe responses. This check box is selected by default.Client Isolation From the drop-down list, select one of the following options:• Enable. Communication between wireless clients that are associated to different virtual access points (VAPs) is blocked.• Disable. Communication between wireless clients that are associated to different VAPs is allowed. This is the default setting.Max. Wireless Clients Enter the maximum number of wireless clients that can simultaneously connect to the wireless access point at one time. The default setting is 64 clients.Table 24. Advanced Wireless Settings (Continued)Field Description

Chapter 5. Advanced Configuration | 81ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Configure Advanced QoS SettingsFor most networks, the default Quality of Service (QoS) queue settings work well. For information about how to configure basic QoS, see Configure Basic Wireless Quality of Service on page 53. You can specify the settings on multiple queues for increased throughput and better performance of differentiated wireless traffic such as Voice-over-IP (VoIP), other types of audio, video, and streaming media, as well as traditional IP data.The advanced QoS options on the wireless access point are as follows:• AP EDCA parameters. Specify the access point (AP) Enhanced Distributed Channel Access (EDCA) settings for different types of data transmitted from the wireless access point to wireless clients.• Station EDCA parameters. Specify the station EDCA parameters for different types of data transmitted from the wireless clients to the wireless access point. If WMM is disabled, you cannot configure the Station EDCA parameters. (For information about how to enable WMM, see Configure Basic Wireless Quality of Service on page 53.)When you configure the EDCA settings, the wireless access point can leverage existing information in the IP packet header that is related to the Type of Service (ToS). The wireless access point examines the ToS field in the headers of all packets that it processes. Based on the value in a packet’s ToS field, the wireless access point prioritizes the packet for transmission by assigning it to one of the queues. A different type of data is associated with each queue. You can configure how the wireless access point treats each queue.The queues defined for different types of data transmitted from AP-to-station and station-to-AP are:• Data 0 (Best Effort). Medium priority queue, medium throughput and delay. Most traditional IP data is sent to this queue.• Data 1 (Background). Lowest priority queue, high throughput. Bulk data that requires maximum throughput and is not time-sensitive is sent to this queue (FTP data, for example).• Data 2 (Video). Highest priority queue, minimum delay. Time-sensitive video data is automatically sent to this queue.• Data 3 (Voice). Highest priority queue, minimum delay. Time-sensitive data such as VoIP and streaming media are automatically sent to this queue.To configure advanced QoS:1. Select Configuration > Wireless > Advanced > QoS Settings. The advanced QoS Settings screen displays.

82 | Chapter 5. Advanced Configuration ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 2. Specify the settings as explained in the following table:Table 25. EDCA Settings Field DescriptionAP EDCA parametersAIFS Enter the Arbitration Inter-Frame Spacing (AIFS) interval that specifies the wait time (in milliseconds) between data frames. A higher AIFS value means a higher priority for a queue. Valid values for AIFS are 0 through 8. The default values are: Data 0: 3; Data 1: 7; Data 2: 1; Data 3: 1.cwMin Enter the Minimum Contention Window (cwMin) value that specifies the upper limit (in milliseconds) of a range from which the initial random back-off wait time is determined. Decreasing this value increases the priority of the queue. The value for cwMin needs to be lower than the value for cwMax. Valid values are 0, 1, 3, 7, 15, 31, 63, 127, 255, 511, or 1023.The default values are: Data 0: 15; Data 1: 15; Data 2: 7; Data 3: 3.cwMax Enter the Maximum Contention Window (cwMax) value that specifies the upper limit (in milliseconds) for the doubling of the random back-off value. Decreasing this value increases the priority of the queue. The value for cwMax needs to be higher than the value for cwMin. Valid values are 0, 1, 3, 7, 15, 31, 63, 127, 255, 511, or 1023. The default values are: Data 0: 63; Data 1: 1023; Data 2: 15; Data 3: 7.Max. Burst Enter the maximum burst value that specifies the maximum burst length (in microseconds) allowed for packet bursts on the wireless network. A packet burst is a collection of multiple frames transmitted without header information. Decreasing this value increases the priority of the queue. Valid values for maximum burst length are all multiples of 32 between 0 and 8192, inclusive of 0 and 8192.The default values are: Data 0: 0; Data 1: 0; Data 2: 3008; Data 3: 1504.Station EDCA parametersAIFS Enter the Arbitration Inter-Frame Spacing (AIFS) interval that specifies the wait time (in milliseconds) between data frames. A higher AIFS value means a higher priority for a queue. Valid values for AIFS are 0 through 8. The default values are: Data 0: 3; Data 1: 7; Data 2: 2; Data 3: 2.cwMin Enter the Minimum Contention Window (cwMin) value that specifies the upper limit (in milliseconds) of a range from which the initial random back-off wait time is determined. Decreasing this value increases the priority of the queue. The value for cwMin needs to be lower than the value for cwMax. Valid values are 0, 1, 3, 7, 15, 31, 63, 127, 255, 511, or 1023.The default values are: Data 0: 15; Data 1: 15; Data 2: 7; Data 3: 3.

Chapter 5. Advanced Configuration | 83ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 3. Click Apply to save your settings. Configure Wireless BridgingThe wireless access point supports a wireless distributing system (WDS) that lets you build large bridged wireless networks. You can select from the following wireless access point modes:• Wireless point-to-point bridge. In this mode, the wireless access point can communicate with another bridge-mode wireless station and, as an option, also with wireless clients. Use WEP, WPA-PSK, or WPA2-PSK to secure the communication. For information about how to configure this mode, see Configure a Point-to-Point Wireless Network on page 84.• Wireless point-to-multipoint bridge. In this mode, the wireless access point is the master for a group of bridge-mode wireless stations. As an option, the wireless access point can also communicate with wireless clients. You can configure up to four profiles. The other bridge-mode wireless stations need to be set to point-to-point bridge mode, using the MAC address of the master wireless access point. Rather than communicating directly with each other, all other bridge-mode wireless stations send their traffic to the master wireless access point. Use WEP, WPA-PSK, or WPA2-PSK to secure the communication. For information about how to configure this mode, see Configure a Point-to-Multipoint Wireless Network on page 87.• Repeater mode. In this mode, this wireless access point operates as a repeater only, and sends all traffic to a remote access point. Repeater mode does not support communication with wireless clients, that is, wireless clients cannot associate with the wireless access point when the wireless access point operates as a repeater. Use WEP, WPA-PSK, or WPA2-PSK to secure the communication. For information about how to configure this mode, see Configure the Wireless Access Point for Repeater Mode on page 91.cwMax Enter the Maximum Contention Window (cwMax) value that specifies the upper limit (in milliseconds) for the doubling of the random back-off value. Decreasing this value increases the priority of the queue. The value for cwMax needs to be higher than the value for cwMin. Valid values are 0, 1, 3, 7, 15, 31, 63, 127, 255, 511, or 1023. The default values are: Data 0: 1023; Data 1: 1023; Data 2: 15; Data 3: 7.TXOP Limit Enter the Transmission Opportunity (TXOP) value that specifies the time interval (in microseconds) in which a client station can initiate transmissions on the wireless medium (WM). Decreasing this value increases the priority of the queue. Valid values for TXOP Limit are all multiples of 32 between 0 and 8192, inclusive of 0 and 8192.The default values are: Data 0: 0; Data 1: 0; Data 2: 3008; Data 3: 1504.Table 25. EDCA Settings (Continued)Field Description

Chapter 5. Advanced Configuration | 95ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual To configure the wireless access point for client mode:1. Select Configuration > Wireless Bridge. The Bridging screen displays.2. Select the Enable Wireless Bridging check box. The Local MAC Address field is a nonconfigurable field that shows the MAC address of the wireless access point.3. Select the Client radio button. (The Edit button becomes nonoperational after you have selected the Client button.)4. As an option, you can now enable MAC cloning, which allows only wireless connections to computers or wireless stations for which you have added the MAC address to the Trusted Wireless Stations table. For more information, see Restrict Wireless Access by MAC Address on page 51.To enable MAC cloning:a. Next to MAC Clone, select the Enable radio button. By default, the Disable radio button is selected.b. In the MAC Clone Address field, enter the MAC address.5. Click Apply to save your settings.

Chapter 6. Troubleshooting | 9666. TroubleshootingThis chapter provides information about troubleshooting your ProSafe Dual Band Wireless-N Access Point WNDAP360. After each problem description, instructions are given to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.• Is the wireless access point on?Go to Basic Functioning on page 97.• Have I connected the wireless access point correctly?Go to Basic Functioning on page 97.• I cannot access the Internet or the LAN.Go to You Cannot Access the Internet or the LAN from a Wireless-Capable Computer on page 98.• I cannot access the wireless access point from a browser.Go to You Cannot Configure the Wireless Access Point from a Browser on page 99.• A time-out occurs.Go to When You Enter a URL or IP Address a Time-Out Error Occurs on page 99.• I cannot remember the wireless access point’s configuration password.Go to Change the Administrator Password on page 65.• I want to clear the configuration and start over again.Go to Restore the Wireless Access Point to the Factory Default Settings on page 63.• The date or time is not correct.Go to Problems with Date and Time on page 101.The wireless access point provides a packet capture tool that enables you to perform problem diagnoses. For information about how to use this tool, go to Use the Packet Capture Tool on page 102.

Chapter 6. Troubleshooting | 97ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Basic FunctioningAfter you turn on power to the wireless access point, check that the following sequence of events occurs:• The Power/Test LED is first steady amber, then goes off, and then blinks green before turning steady green after about 45 seconds.• The Active LED is lit or blinks green when there is Ethernet traffic.• The LAN LED indicates the LAN speed: green for 1000 Mbps, amber for 100 Mbps, and no light for 10 Mbps.• The WLAN LED is lit or blinks green when the wireless LAN (WLAN) is ready.If any of these conditions does not occur, see to the appropriate following section.No LEDs Are Lit on the Wireless Access PointIt takes a few seconds for the power LED to light up. Wait a minute and check the Power LED status on the wireless access point. If the wireless access point has no power:If you use a PoE switch to provide power to the wireless access point, check these items:• Make sure that the Ethernet cable between the wireless access point and the PoE switch is correctly connected at both ends.• Make sure that the power cord of the PoE switch is plugged into a working power outlet or power strip.• Make sure that your PoE switch is functioning normally.If you use a power cord to provide power to the wireless access point, check these items:• Make sure that the power cord is connected to the wireless access point.• Make sure that the power adapter is connected to a functioning power outlet. If it is in a power strip, make sure that the power strip is turned on. If it is plugged directly into the wall, verify that it is not a switched outlet.• Make sure that you are using the correct NETGEAR power adapter that is supplied with your wireless access point.The Active LED or the LAN LED Is Not LitThere is a hardware connection problem.Check these items:• Make sure that the cable connectors are securely plugged in at the wireless access point and the network device—hub, (PoE) switch, or router.

98 | Chapter 6. Troubleshooting ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual • Make sure that the connected device is turned on.• Make sure that the correct cable is used. Use a standard Category 5 Ethernet patch cable. If the network device has Auto Uplink™ (MDI/MDIX) ports, you can use either a crossover cable or a normal patch cable.The WLAN LED Does Not Light UpThe wireless access point’s antenna is not working.Check these items:• If the WLAN LED remains off, either disconnect the cable to the PoE switch and then reconnect it again, or disconnect the adapter from its power source and then plug it in again.• Make sure that optional external antennas are tightly connected to the wireless access point. Contact NETGEAR technical support if the WLAN LED remains off.You Cannot Access the Internet or the LAN from a Wireless-Capable ComputerThere is a configuration problem. Check these items:• You might not have restarted the computer with the wireless adapter to allow TCP/IP changes take effect. Restart the computer.• The computer with the wireless adapter might not have the correct TCP/IP settings to communicate with the network. Restart the computer and check that TCP/IP is set up correctly for that network. In Windows, the usual setting for Network Properties is to obtain an IP address automatically.• The wireless access point’s default values might not work with your network. Check the wireless access point’s default configuration against the configuration of other devices in your network.• Make sure that the SSID, network authentication, and data encryption settings of the computer with the wireless adapter are the same as those of the wireless access point.• Ping the IP address of the wireless access point to verify that there is a wireless connection between the computer with the wireless adapter and the wireless access point. If the ping fails, check the network configuration (for the wireless access point, see Configure IP Settings and Optional DHCP Server Settings on page 20).• Ping the default gateway to verify that there is a path from the computer with the wireless adapter to the default gateway. If the ping fails, check the network configuration or call the Internet Service Provider (ISP).

Chapter 6. Troubleshooting | 99ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual You Cannot Configure the Wireless Access Point from a BrowserCheck these items:• The wireless access point is correctly installed, it is powered on, and LAN connections are okay. Check that the Active LED and LAN LED are on to verify that the Ethernet connection is okay. • If your computer uses a fixed (static) IP address, ensure that it is using an IP address in the range of the wireless access point. The wireless access point’s default IP address is 192.168.0.100, and its subnet mask is 255.255.255.0 with DHCP disabled. Make sure that your network configuration settings are correct.• If you are using the NetBIOS name of the wireless access point to connect, ensure that your computer and the wireless access point are on the same network segment or that there is a WINS server on your network. • If your computer is set to Obtain an IP address automatically (DHCP client), restart it.• Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet Explorer, click Refresh to be sure that the Java applet is loaded.• Try quitting the browser and launching it again.• Make sure that you are using the correct login information. The factory default login name is admin, and the password is password. Make sure that Caps Lock is off when entering this information.If the wireless access point does not save changes you have made in the Web Management Interface, check the following:• When entering configuration settings, be sure to click the Apply button before moving to another screen or tab, or your changes are lost.• Click the Refresh or Reload button in the Web browser. The changes might have occurred, but the Web browser might be caching the old configuration.When You Enter a URL or IP Address a Time-Out Error OccursA number of things could be causing this.Try the following troubleshooting steps:• Check whether other computers on the LAN work correctly. If they do, ensure that your computer’s TCP/IP settings are correct. If you use a fixed (static) IP address, check the subnet mask, default gateway, DNS, and IP addresses of the wireless access point (see Configure IP Settings and Optional DHCP Server Settings on page 20).

100 | Chapter 6. Troubleshooting ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual • If the computer is configured correctly but still not working, ensure that the wireless access point is connected and turned on. Access it and check its settings. If you cannot connect to the wireless access point, check the LAN and power connections.• If the wireless access point is configured correctly, check your Internet connection (for example, your cable modem) to make sure that it is working correctly.Troubleshooting a TCP/IP Network Using the Ping UtilityMost TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply. You can easily troubleshooting a TCP/IP network by using the ping utility in your computer.Testing the LAN Path to Your Wireless Access PointYou can ping the wireless access point from your computer to verify that the LAN path to your wireless access point is set up correctly.To ping the wireless access point from a computer running Windows 95 or later:1. From the Windows toolbar, click the Start button, and select Run.2. In the field provided, type ping followed by the IP address of the wireless access point, as in this example: ping 192.168.0.2293. Click OK.You should see a message like this one:Pinging <IP address> with 32 bytes of dataIf the path is working, you see this message:Reply from < IP address >: bytes=32 time=NN ms TTL=xxxIf the path is not working, you see this message:Request timed outIf the path is not functioning correctly, you could have one of the following problems:• Wrong physical connections:- Make sure that the Active LED and LAN LED are on. If one or both of these LEDs are off, follow the instructions in The Active LED or the LAN LED Is Not Lit on page 97.- Check that the corresponding link LEDs are on for your network interface card and for the hub ports (if any) that are connected to your workstation and wireless access point.• Wrong network configuration:

Chapter 6. Troubleshooting | 101ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual - Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your computer.- Verify that the IP address for your wireless access point and your workstation are correct and that the addresses are on the same subnet.Testing the Path from Your Computer to a Remote DeviceAfter verifying that the LAN path works correctly, test the path from your computer to a remote device. 1. From the Windows toolbar, click the Start button, and select Run.2. In the Windows Run window, type:Ping -n 10 IP addresswhere IP address is the IP address of a remote device such as your ISP’s DNS server.If the path is functioning correctly, replies as in the previous section display. If you do not receive replies:• Check that your computer has the IP address of your router listed as the default wireless access point. If the IP configuration of your computer is assigned by DHCP, this information is not visible in your computer’s Network Control Panel. Verify that the IP address of the router is listed as the default wireless access point.• Check to see that the network address of your computer (the portion of the IP address specified by the netmask) is different from the network address of the remote device.• Check that your cable or DSL modem is connected and functioning.• If your ISP assigned a host name to your computer, enter that host name as the account name in the basis General system settings screen (see Configure Basic General System Settings and Time Settings on page 18).Problems with Date and TimeThe Time Settings screen that is accessible through the Configuration > System > Basic > Time menu choices displays the current date and time of day. The wireless access point uses the Network Time Protocol (NTP) to obtain the current time from a network time servers on the Internet that you specify in the Time Settings screen (see Configure Basic General System Settings and Time Settings on page 18). Each entry on the Logs screen is stamped with the date and time of day. Problems with the date and time function can include:• Date and time shown is Fri Dec 31 00:00:00 1999 or a similar incorrect date and time. Cause: The wireless access point has not yet successfully reached the network time server. Check that your Internet access settings are configured correctly. If you have just completed configuring the wireless access point, wait at least 5 minutes and check the date and time again.• The day is correct or one day ahead or behind, and the hours are ahead or behind. Cause: You have selected an incorrect time zone for your area. Specify the correct time

102 | Chapter 6. Troubleshooting ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual zone in the basic General system settings screen (see Configure Basic General System Settings and Time Settings on page 18).Use the Packet Capture ToolYou can capture wireless packets to analyze traffic patterns with a network traffic analyzer tool. The captured packet flow can show if traffic is flowing correctly to its destinations or if packets are dropped. There is a limit to the size of the packet flow that you can capture in a file.To capture packets:1. Select Monitoring > Packet Capture. The Packet Capture screen displays:Figure 47. 2. Click Start to start capturing wireless packets leaving or entering the wireless access point on the active operating channel. Packets on the 2.4-GHz interface are captured. Normal functioning of the wireless access point is not affected during the packet capture process.If any previously captured packets exist, you are prompted to delete them, and only then can you capture new packets.3. Click Stop to stop capturing packets.4. Click Save as to save the pacture.pcap file on your computer or to a disk drive.

Appendix A. Supplemental Information | 103AA. Supplemental InformationThis appendix provides related documentation, factory default settings, and technical specifications for the ProSafe Dual Band Wireless-N Access Point WNDAP360.• Technical Specifications on page 103• Factory Default Settings on page 105Technical SpecificationsTable 29. ProSafe Dual Band Wireless-N Access Point WNDAP360 Technical SpecificationsFeature Description802.11b/bg/ng Wireless Specifications802.11g data rates 1, 2, 5.5, and 11 Mbps (auto-rate capable)802.11bg data rates 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps (auto-rate capable)802.11ng MCS index and data rates Data rates for a 20 MHz channel width and a short guard interval (400 ms):Best, 0 / 7.2 Mbps, 1 / 14.4 Mbps, 2 / 21.7 Mbps, 3 / 28.9 Mbps, 4 / 43.3 Mbps, 5 / 57.8 Mbps, 6 / 65 Mbps, 7 / 72.2 Mbps, 8 / 14.44 Mbps, 9 / 28.88 Mbps, 10 / 43.33 Mbps, 11 / 57.77 Mbps, 12 / 86.66 Mbps, 13 / 115.56 Mbps, 14 / 130 Mbps, 15 / 144.44 MbpsBest, 6.5 Mbps, 13 Mbps, 19.5 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 58.5 Mbps, 65 Mbps, 13 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 78 Mbps, 104 Mbps, 117 Mbps, 130 MbpsData rates for a 40 MHz channel width and a short guard interval (400 ms):Best, 0 / 15 Mbps, 1 / 30 Mbps, 2 / 45 Mbps, 3 / 60 Mbps, 4 / 90 Mbps, 5 / 120 Mbps, 6 / 135 Mbps, 7 / 150 Mbps, 8 / 30 Mbps, 9 / 60 Mbps, 10 / 90 Mbps, 11 / 120 Mbps, 12 / 180 Mbps, 13 / 240 Mbps, 14 / 270 Mbps, 15 / 300 MbpsBest, 13.5 Mbps, 27 Mbps, 40.5 Mbps, 54 Mbps, 81 Mbps, 121.5 Mbps, 135 Mbps, 27 Mbps, 54 Mbps, 81 Mbps, 162 Mbps, 216 Mbps, 243 Mbps, 270 Mbps

104 | Appendix A. Supplemental Information ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual 802.11b/bg/ng operating frequencies • 2.412–2.462 GHz (US)• 2.457–2.462 GHz (Spain)• 2.41–2.484 GHz (Japan 11b)• 2.41–2.472 GHz (Japan 11ng)• 2.457–2.472 GHz (France)• 2.412–2.472 GHz (Europe ETSI)802.11 b/bg/ng encryption • 64-bit, 128-bit, and 52-bit WEP• AES• TKIP802.11a/na Wireless Specifications802.11a data rates 6, 9, 12, 18, 24, 36, 48, 54, and 108 Mbps (auto-rate capable)802.11na data rates Data rates for a 20 MHz channel width and a short guard interval (400 ms): Best, 7.2 Mbps, 14.4 Mbps, 21.7 Mbps, 28.9 Mbps, 43.3 Mbps, 57.8 Mbps, 65 Mbps, 72.2 Mbps, 14.44 Mbps, 28.88 Mbps, 43.33 Mbps, 57.77 Mbps, 86.66 Mbps, 115.56 Mbps, 130 Mbps, 144.44 MbpsData rates for a 20 MHz channel width and a long guard interval (800 ms):Best, 6.5 Mbps, 13 Mbps, 19.5 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 58.5 Mbps, 65 Mbps, 13 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 78 Mbps, 104 Mbps, 117 Mbps, 130 MbpsData rates for a 40 MHz channel width and a short guard interval (400 ms):Best, 15 Mbps, 30 Mbps, 45 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 135 Mbps, 150 Mbps, 30 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 180 Mbps, 240 Mbps, 270 Mbps, 300 MbpsData rates for a 40 MHz channel width and a long guard interval (800 ms):Best, 13.5 Mbps, 27 Mbps, 40.5 Mbps, 54 Mbps, 81 Mbps, 121.5 Mbps, 135 Mbps, 27 Mbps, 54 Mbps, 81 Mbps, 162 Mbps, 216 Mbps, 243 Mbps, 270 Mbps802.11a/na Operating Frequencies 5150–5250 MHz (FCC operating frequencies)5725–5825 MHz (FCC operating frequencies)5150–5250 MHz (CE [EU] operating frequencies)5250–5350 Mz (CE [EU] operating frequencies)5470–5725 MHz (CE [EU] operating frequencies)802.11 a/na encryption • 64-bit, 128-bit, and 52-bit WEP• AES• TKIPManagement and Other SpecificationsNetwork management • Remote configuration and management through Web Management Interface, SNMP, or Telnet with command-line interface (CLI)• SNMP management supports SNMP MIB I, MIB II, 802.11 MIB and proprietary configuration MIBTable 29. ProSafe Dual Band Wireless-N Access Point WNDAP360 Technical SpecificationsFeature Description

Appendix A. Supplemental Information | 105ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Factory Default SettingsYou can use the Reset button located on the rear of the wireless access point to reset all settings to their factory defaults. This is called a hard reset. To perform a hard reset, use a sharp object to push and hold the Reset button for approximately 5 seconds (until the Test LED blinks rapidly). This returns the wireless access point to the factory configuration settings that are shown in the following table.Note: Pressing the Reset button for a shorter period of time simply causes the wireless access point to reboot.Maximum clients Limited by the amount of wireless network traffic generated by each node; maximum 64 supportedStatus LEDs • Power/Test LED• Link speed LED• Ethernet LAN• Wireless LANElectrical and Physical SpecificationsPower adapter 12 VDC, 1A; plug is localized to country of salePhysical specifications • Dimensions (h x w x d): 253.75 x 253.75 x 54.76 mm (10.0 x 10.0 x 2.16 in)• Weight: 0.886 kg (1.95 lb)Environmental specifications Operating temperature: 0 to 55° C (32 to 131° F)Operating humidity: 10–9%, noncondensingComplianceNote: For more information about compliance, see Appendix C, Notification of Compliance.Electromagnetic compliance FCC Part 15 Class B and Class E, CE, and C-TICKTable 29. ProSafe Dual Band Wireless-N Access Point WNDAP360 Technical SpecificationsFeature Description

106 | Appendix A. Supplemental Information ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Table 30. ProSafe Dual Band Wireless-N Access Point WNDAP360 Default Configuration Settings Feature DescriptionLoginUser login URL 192.168.0.100User name (case-sensitive) admin Login password (case-sensitive) passwordEthernet ConnectionStatic IP address 192.168.0.210Ethernet MAC address See bottom label.Port speed 10/100/1000Local Network (LAN)LAN IP address 192.168.0.100Subnet mask 255.255.255.0Gateway address 0.0.0.0DHCP server DisabledDHCP client DisabledTime zone USA-PacificSNMP DisabledSpanning Tree Protocol DisabledSecure Shell (SSH) EnabledSecure Telnet Disabled

Appendix A. Supplemental Information | 107ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Wireless Local Network (WLAN)Operating mode Access point, infrastructure modeWireless access point name netgearxxxxxx where xxxxxx is the last 6 digits of the wireless access point MAC address.Wireless communication Enabled11 b/g/n wireless network name (SSID) NETGEAR_11ngBroadcast network name SSID EnabledSecurity Disabled (open system)Transmission speed BestaCountry and region Varies by region802.11ng radio frequency channel AutoOutput power FullWireless card access list All wireless stations allowedWMM support Enableda. Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.Table 30. ProSafe Dual Band Wireless-N Access Point WNDAP360 Default Configuration Settings (Continued)Feature Description

Appendix B. Command-Line Reference | 108BB. Command-Line ReferenceThe ProSafe Dual Band Wireless-N Access Point WNDAP360 can be configured through either the command-line interface (CLI), a Web browser, or a MIB browser. The CLI allows viewing and modification of the configuration from a terminal or computer through a Telnet connection.Keyword Description-------------------------------------- ----------------------|-backup-configuration --backup configuration|-config> --configuration setting| |-apname --access point name| |-country --country/region| |-dhcp> --DHCP server| | |-dns-server --DNS server| | |-gateway --default gateway| | |-ip-address --IP range| | |-lease-time --lease time| | |-status --status| | |-subnet-mask --subnet mask| | |-wins-server --WINS server| || |-http-redirect --enable HTTP redirection | |-http-redirect-url --HTTP redirection URL| |-interface> --select wireless lan interface| | |-wlan> --wireless LAN interface setting| | | |-2.4GHz> --2.4 GHz wireless LAN interface setting| | | | |-aggregation-length --aggregated packet size| | | | |-ampdu --aggregated MAC Protocol Data Unit| | | | |-beacon-interval --wireless beacon period in TU(1024 us)| | | | |-channel --wireless channel (depends on country and wireless mode)| | | | |-channelwidth --wireless channel width| | | | |-dtim-interval --wireless DTIM period in beacon interval| | | | |-extension-protection-spacing --wireless extension protection spacing| | | | |-fragmentation-length --wireless fragmentation threshold(even only)| | | | |-guardinterval --interval (from interference from other transmissions)| | | | |-knownap-add --add known access point| | | | |-knownap-del --delete known access point

Appendix B. Command-Line Reference | 119ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual | | |-syslog-server-ip --syslog server IP address| | |-syslog-server-port --syslog server port number| || |-radius>| | |-accounting-server-primary --primary accounting server| | |-accounting-server-primary-port --primary accounting server port| | |-accounting-server-primary-sharedsecret --primary accounting server shared secret| | |-accounting-server-secondary --secondary accounting server| | |-accounting-server-secondary-port --secondary accounting server port| | |-accounting-server-secondary-sharedsecret --secondary accounting server shared secret| | |-authentication-server-primary --primary authentication server| | |-authentication-server-primary-port --primary system accounting server shared| | | secret| | |-authentication-server-primary-sharedsecret --primary authentication server shared secret| | |-authentication-server-secondary --secondary authentication server| | |-authentication-server-secondary-port --secondary authentication server port| | |-authentication-server-secondary-sharedsecret --secondary authentication server shared| | | secret| || |-remote> --enable remote access via SSH | | |-ssh-port --SSH port| | |-sshd --SSH daemon| | |-telnet --enable remote access via Telnet| | | |-snmp> --SNMP setting| | |-description --SNMP system description| | |-read-community --SNMP ReadCommunity | | |-snmp-status --SNMP status| | |-trap-community --SNMP ReadCommunity | | |-trap-server --SNMP TrapServer IP address| | |-write-community --SNMP WriteCommunity| | | |-spanning-tree --enable spanning tree protocol| |-time> --time Setting| | |-custom-ntp-server --custom NTP server host name| | |-daylightsaving --daylight saving| | |-ntp-client --NTP client host name| | |-ntp-server --NTP server host name| | |-time-zone --time zone| | | |-vlan> --vlan settings| | |-management-vlan --vlan management id| | |-untagged-vlan --untagged vlan id| | |-untagged-vlan-status --untagged vlan status| | | |-exit --logout from CLI

120 | Appendix B. Command-Line Reference ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual |-file --|-firmware-upgrade --upload new system firmware file|-password --system password|-restore-configuration --restore system configuration|-restore-default-password --restore default system password|-show> --show system settings| |-configuration --show system configuration| |-interface> --show wireless lan interface| | |-eth> --ethernet interface| | | |-statistics --show ethernet statistics| | | | | |-wlan> --wlan interface settings| | | |-2.4GHz> --2.4GHz wlan interface settings| | | | |-configuration --interface configuration| | | | |-knownaplist --known access point list| | | | |-stationlist --station list| | | | |-statistics --interface statistics| | | | |-trusted-stationlist --trusted station list | | | | |-unknownaplist --unknown access point list| | | | | | | |-5GHz> --5GHz wlan interface settings| | | | |-configuration --interface configuration | | | | |-knownaplist --known access point list| | | | |-stationlist --station list| | | | |-statistics --interface statistics| | | | |-trusted-stationlist --trusted station list | | | | |-unknownaplist --unknown access point list| | | | | | | | | | |-log --system log | |-system --system setting

Appendix C. Notification of Compliance | 121CC. Notification of ComplianceNETGEAR Dual Band - WirelessRegulatory Compliance InformationThis section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.Note: This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user's guide may not be available in your version of the product.Europe - EU Declaration of ConformityMarking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: EN300 328 (2.4 Ghz), EN301 489-17, EN301 893 (5 Ghz), EN60950-1For complete DoC please visit the NETGEAR EU Declarations of Conformity website at: http://support.netgear.com/app/answers/detail/a_id/11621/ EDOC in Languages of the European CommunityLanguage StatementCesky [Czech] NETGEAR Inc. tímto prohlašuje, že tento Radiolan je ve shode se základními požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES.Dansk [Danish] Undertegnede NETGEAR Inc. erklærer herved, at følgende udstyr Radiolan overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Deutsch [German]Hiermit erklärt NETGEAR Inc., dass sich das Gerät Radiolan in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Eesti [Estonian] Käesolevaga kinnitab NETGEAR Inc. seadme Radiolan vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.English Hereby, NETGEAR Inc., declares that this Radiolan is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual122 | Appendix C. Notification of Compliance Español [Spanish]Por medio de la presente NETGEAR Inc. declara que el Radiolan cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Ελληνική [Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR Inc. ΔΗΛΩΝΕΙ ΟΤΙ Radiolan ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.Français [French]Par la présente NETGEAR Inc. déclare que l'appareil Radiolan est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Italiano [Italian] Con la presente NETGEAR Inc. dichiara che questo Radiolan è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Latviski [Latvian]Ar šo NETGEAR Inc. deklarē, ka Radiolan atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.Lietuvių [Lithuanian] Šiuo NETGEAR Inc. deklaruoja, kad šis Radiolan atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Nederlands [Dutch]Hierbij verklaart NETGEAR Inc. dat het toestel Radiolan in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Malti [Maltese] Hawnhekk, NETGEAR Inc., jiddikjara li dan Radiolan jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.Magyar [Hungarian]Alulírott, NETGEAR Inc. nyilatkozom, hogy a Radiolan megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Polski [Polish] Niniejszym NETGEAR Inc. oświadcza, że Radiolan jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.Português [Portuguese]NETGEAR Inc. declara que este Radiolan está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Slovensko [Slovenian]NETGEAR Inc. izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Slovensky [Slovak]NETGEAR Inc. týmto vyhlasuje, že Radiolan spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Suomi [Finnish] NETGEAR Inc. vakuuttaa täten että Radiolan tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Svenska [Swedish]Härmed intygar NETGEAR Inc. att denna Radiolan står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual Appendix C. Notification of Compliance | 123This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.FCC Requirements for Operation in the United States FCC Information to UserThis product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.FCC Guidelines for Human Exposure (Radiation Exposure Statement)This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.FCC Declaration of ConformityWe, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the ProSafe Dual Band Wireless-N Access Point WNDAP360 complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:• This device may not cause harmful interference, and• This device must accept any interference received, including interference that may cause undesired operation.FCC Radio Frequency Interference Warnings & InstructionsThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution• Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This device is for operation within the 5.150 ~ 5.250 GHz frequency range, and it is restricted to an indoor environment.Íslenska [Icelandic]Hér með lýsir NETGEAR Inc. yfir því að Radiolan er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.Norsk [Norwegian]NETGEAR Inc. erklærer herved at utstyret Radiolan er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual124 | Appendix C. Notification of Compliance • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.• For products available in the USA market, only channel 1 ~ 11 can be operated. Selection of other channels is not possible.Industry CanadaThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device has been designed to operate with an antenna having a maximum gain of 6.29dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.IMPORTANT NOTE: Radiation Exposure StatementThis equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.CautionThe device for operation in the band 5150 - 5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radars are allocated as primary users (that is, priority users) of the bands 5250 - 5350 MHz and 5650 - 5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Industrie CanadaCe dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de dB 6.29. Une antenne à gain plus élevé est strictement interdite par les règlements d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante.NOTE IMPORTANTE: Déclaration d'exposition aux radiationsCet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.AvertissementLes dispositifs fonctionnant dans la bande 5150 - 5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250 - 5350 MHz et 5650 - 5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

Index | 125IndexNumerics11b, 11bg, 11ng (wireless modes) 24, 262.4 GHz/5 GHz concurrent 82.4-GHz antenna, connector for 12802.11d support 80802.1Q VLAN 8Aaccess control, wireless stations 44access point EDCA parameters 82access, restricting by MAC address 51accounting, RADIUS servers 49, 50Active LEDbehavior 17description 11troubleshooting 97ActiveX 99activity log 71admin passwordchanging or restoring 65default 106Advanced Encryption Standard (AES) 37, 47, 49Aggregated MAC Protocol Data Unit (A-MPDU) frames 80aggregation length 80antennaenabling internal or external 80external orientation 15Arbitration Inter-Frame Spacing (AIFS) interval 82associated identifier (AID) 70associations, clients 73Australia, channels/frequency 25, 26authenticationnetwork 37RADIUS servers 49, 50autosensing over Ethernet 9Bbackground trafficadvanced QoS 81WMM QoS 53backing up 61basic service set (BSS) 38basic service set identifier (BSSID)combining with VLANs 36number supported 37beacon interval 79beacons, unknown access points 75best effort trafficadvanced QoS 81WMM QoS 53bridging, wireless 83broadcast packets, transmitted and received 73broadcasting, wireless network name (SSID) 24, 26, 36, 41browsers, recommended 17BSS (basic service set) 38BSSID (basic service set identifier)combining with VLANs 36number supported 37bytes, received and transmittedover Ethernet connection 72over wireless connection 71CCanada, channels/frequency 25, 26capturing packets 102Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) 79Carrier Sense Multiple Access with Collision Detection (CSMA/CD) 79Category 5 Ethernet cable 7channel bonding 25, 27channel width and offset (11ng only) 25, 27channelsdefaults 25, 26wireless spacing 15Clear to Send (CTS) packets 79CLI command sets 108client mode, bridgingconfiguring 94description 84clients

126 | Index ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual associations 73DHCP 21isolation 80maximum number 80NTP 20wireless separation 38, 43compliance 121electromagnetic 105concurrent dual band, use 8configuration file, backing up or restoring 61connectors and ports, rear panel 12console port 12cwMax (Maximum Contention Window) value 82cwMin (Minimum Contention Window) value 82Ddata encryptionkey generation, WEP 46key size, WEP 45WPA and WPA2 49data rate (11b and 11bg only) 25, 27data rates 103date, troubleshooting 101defaultschannels 25, 26DHCP gateway 23factory settings 105factory, restoring to 63frequency 25, 26IP address 17ISP gateway 21login password 106password 17SNMP 56subnet mask 21, 106user name 17, 106Delivery Traffic Indication Message (DTIM) interval 80DHCPclients 21servers 23DNS serversDHCP 23ISP 21dual band concurrent, use 8dynamic and static VLANs 43Eelectromagnetic compliance 105encryptionkey generation, WEP 46key size, WEP 45WPA and WPA2 49Enhanced Distributed Channel Access (EDCA) parameters 81environmental specifications 105Ethernet cabling requirements 15Europe, channels/frequency 25, 26Extended Service Set (ESS) 38external antenna, enabling 80Ffactory default settings 105firmwarebacking up 61factory defaults 63restoring 62upgrade 59version 68flash memory 58fragmentation length 79frequency, defaults 25, 26FTP trafficadvanced QoS 81WMM QoS 53Ggatewaysdefault (ISP) 21DHCP 23generating keys, WEP 45Gigabit Ethernet (RJ-45) port 12graphical user interface (GUI)description 18troubleshooting 99guard interval (11ng only) 25, 27Hhalf-duplex mode 94hotspot, server 78HTTP redirect, enabling 78Iidle time 71importing, file with known access points 74infrastructure mode 28installation kits 29installation order 16interferencechannels 15

Index | 127ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual sources of 15internal antenna, disabling 80Internet browsing, troubleshooting 98IP addressesdefault 17, 21DHCP DNS servers 23DHCP ranges 23DHCP WINS servers 23ISP DNS servers 21LAN 106NTP servers 20RADIUS servers 50SNMP manager 56static 106syslog server 66TFTP server 61isolation, clients 80JJava and Javascript 99Kkey update, RADIUS servers 51keys, generation, WEP 46LLANconfiguration requirements 15IP address 106troubleshooting 98LAN LEDbehavior 17description 12troubleshooting 97LAN path, troubleshooting 100lease, DHCP 23LEDsbehavior 17description 11startup procedure 97troubleshooting 97legacy 802.1X (wireless security) 42, 46local MAC addresses 51location, country and region 19log, activities 71logging in 17login URL, name, and password 106losing, wireless connection 52MMAC addressesEthernet port 68known access points 75restricting access by 36, 51unknown access points 74wireless access point 19wireless card 68management VLAN 77management, options 55maximum burst value 82Maximum Contention Window (cwMax) value 82maximum number of clients 80MCS, index and data rate (11ng only) 25, 27Minimum Contention Window (cwMin) value 82mixed mode. See WPA and WPA2 mixed mode.Modulation and Coding Scheme (MCS) 25, 27mounting plateceiling 29wall 31multicast packets, transmitted and received 73Nname, wireless access point 19names, profiles 41NetBIOS name 19networkauthentication 37configuration, troubleshooting 100integrity check 21Network Time Protocol (NTP), client and server 20Oopen system 42operating frequencies 104order of installation and configuration 16output power, transmission 25, 27Ppackage contents 7packetscapturing 102Ethernet, received and transmitted 72wireless, received and transmitted 73passphraseWEP 45WPA, WPA2, and mixed mode 49passwordchanging or restoring 65default 17login 106

128 | Index ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual physical connections 100physical specifications 105pinging, wireless access point 98, 100placement, wireless equipment 14point-to-multipoint bridgeconfiguring 87description 83point-to-point bridgeconfiguring 84description 83policy, access control 44port and connectors, rear panel 12portsRADIUS servers 50SNMP manager, traps 56syslog server 66power adapter 105Power over Ethernet (PoE) 9, 17Power/Test LEDbehavior 17description 11troubleshooting 97powersaving, WMM 54preamble type 80pre-shared key (PSK). See WPA, see WPA2, and see WPA and WPA2 mixed mode.priority queuesadvanced QoS 81WMM QoS 53profile settings 41profiles, securitycreating and configuring 40description 37protection spacing (11ng only) 25, 27QQoS (quality of service)advanced 81WMM 53Rradioscheduling 52turning off 24, 26RADIUS servers, configuring 49range guidelines, wireless equipment 14read-only name, read-write name, SNMP 56rear panel 12reauthentication time, RADIUS servers 51rebooting, from Web Management Interface 64received signal strength indicator (RSSI) 71redirecting, HTTP requests 78Reduced Interframe Space (RIFS) transmission 80remote devices, troubleshooting 101remote MAC addresses 51remote management, options 55repeater mode, bridgingconfiguring 91description 83Request to Send (RTS) threshold 79Reset button 12, 64, 105restoringfactory defaults 63password 66settings 62restricting access, by MAC address 36RIFS (Reduced Interframe Space) transmission 80roaming 38rogue access points, detection of 73RSSI (received signal strength indicator) 71RTS (Request to Send) threshold 79Rx sequence 71Sscheduling, wireless radio 52Secure Shell (SSH), enabling 57security lock 13security profilescreating and configuring 40description 37security, wireless options 35separation, wireless clients 38, 43serversDHCP 23DNS 21hotspot 78NTP 20RADIUS 49syslog 66service set identifiers. See SSIDs.shared key 42, 45shared secrets, RADIUS servers 50show configuration, CLI command 58signal-to-noise ratio (SNR) 71SMA connectors 12SNMPdefaults 56manager, IP address 56softwarebacking up 61

Index | 129ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual factory defaults 63restoring 62upgrading 59version 68Spanning Tree Protocol (STP), enabling 77specificationsenvironmental 105physical 105SSH (Secure Shell), enabling 57SSIDsbroadcasting 24, 26, 36changing 24, 26, 41matching 28static and dynamic VLANs 43station EDCA parameters 82statistics, traffic 72STP (Spanning Tree Protocol), enabling 77streaming mediaadvanced QoS 81WMM QoS 53subnet maskdefault 106DHCP clients 23wireless access point 21supported standards 8syslog 66system requirements 7Ttagged VLAN 77TCP/IP network, troubleshooting 100technical specifications 103technical support 2Telnet, enabling 57Temporal Key Integrity Protocol (TKIP) 37TFTP server, upgrade procedure 60time and time zoneconfiguring 20troubleshooting 101time-out error 99TKIP (Temporal Key Integrity Protocol) 37, 47, 49TKIP + AES (WPA & WPA2 mixed mode) 47top panel 11trademarks 2trafficadvanced QoS 81patterns, analyzing 102statistics 72WMM QoS 53Transmission Opportunity (TXOP) limit 83transmission output power 25, 27trap community name 56traps, SNMP 56troubleshooting 100basic functioning 97browser configuration 99capturing packets 102date 101Internet and LAN connection 98LAN path 100LEDs 97network configuration 100path to remote device 101physical connections 100pinging 98, 100PoE connection 97power cord 97TCP/IP settings 98time and time zone 101time-out error 99trusted, wireless stations 52Tx sequence 71TXOP (Transmission Opportunity) limit 83Uunicast packetsencryption methods 47transmitted and received 73Unites States, channels/frequency 25, 26untagged VLAN 76upgrading, software 59URLs, redirecting 78user name, default 17, 106Vversion, software 68video trafficadvanced QoS 81WMM QoS 53VLANsdynamic and static 43identifiers (IDs) 38, 43tagged, untagged, and management, enabling 76VoIP trafficadvanced QoS 81WMM QoS 53Wweb browsers, recommended 17Web Management Interfacedescription 18troubleshooting 99

130 | Index ProSafe Dual Band Wireless-N Access Point WNDAP360 Reference Manual WEPconfiguring with a shared key 42, 45configuring with RADIUS 42, 46data encryption, key size 45legacy 802.1X 46open system 44passphrase 45types of encryption 36Wi-Fi Multimedia (WMM) 10, 53, 54Wi-Fi protected access. See WPA and see WPA2.WINS servers 23wired equivalent privacy. See WEP.wireless adapters, 802.11b/g and 802.11n 15wireless bridging 83wireless clients, separation 38, 43wireless connection, losing 52wireless equipment, placement and range 14wireless modes 24, 26wireless network name (SSID)broadcasting 24, 26changing 24, 26, 41wireless securityoptions 35settings 42wireless stationsaccess control 44trusted 52WLAN LEDbehavior 17description 12troubleshooting 98WMM (Wi-Fi Multimedia) 10, 53, 54WPAadapter restrictions 42configuring with PSK 42, 48configuring with RADIUS 42, 46encryption 49passphrase 48, 49TKIP 47, 49types of encryption 37WPA and WPA2 mixed modeadapter restrictions 42configuring with PSK 43, 48configuring with RADIUS 42, 47encryption 49passphrase 48, 49TKIP + AES 47, 49types of encryption 37WPA2adapter restrictions 42AES 47, 49configuring with PSK 43, 48configuring with RADIUS 42, 47encryption 49passphrase 48, 49types of encryption 37

Navigation menu