Netgear orporated 14100251 Universal WiFi Range Extender User Manual 2

Notification of Compliance

Regulatory Compliance Information

This document includes user requirements for operating NETGEAR products in accordance with national laws

including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the

applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable

national regulatory authority.

The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country.

data gateways.

Europe – EU Declaration of Conformity

This section applies to products bearing the CE or CE! mark:

Products bearing the CE or CE! mark comply with the following EU directives:

 EMC Directive 2004/108/EC

 Low Voltage Directive 2006/95/EC

 Ecodesign Directive 2009/125/EC

 RoHS Directive 2011/65/EU

If the product has telecommunications functionality, it also complies with the requirement of the following EU

aware that outdoor installations require special attention and will only be handled by trained and qualified installation

personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when

external antennas, power and grounding must be installed for use. Particular attention has to be given allowed

operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if

this product requires the special considerations for outdoor installations. For detailed information concerning

installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ )

The following paragraphs apply to WN2500RP:

This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU

contact the national spectrum authority in France.

Warning

NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference

in which case the user may be required to take adequate measures.

FCC Requirements for Operation in the United States

Information in this section applies to products bearing the FCC mark (or statement):

FCC Information to User

This NETGEAR product does not contain any user serviceable components and is to be used with approved

 WN370

 WN2500RP

 WN3000RPv2

 WN3500RP

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or

transmitter except in accordance with FCC multi-transmitter product procedures.

FCC Guidelines for Human Exposure

This NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The

equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

FCC Declaration of Conformity

The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following methods:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is

human body.

NETGEAR products that are intended to be operated close to the human body are tested for body-worn Specific

Absorption Rate (SAR) compliance. The SAR limit set by the FCC is 1.6 W/kg.

The FCC has established detailed SAR requirements and NETGEAR products meet these requirements.

NETGEAR USB products were tested while installed in a host notebook computer.

RF Exposure Information

NETGEAR products have been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the

requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio

frequency devices. NETGEAR products meet the applicable government requirements for exposure to radio

frequency waves. To see the test results reporting the highest SAR level measured for this device, visit

http://www.netgear.com/about/regulatory/declarations-conformity/

NETGEAR products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)

NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference

received, including interference that may cause undesired operation.

For products available in the USA market, only channel 1~11 can be operated. Selection of other channels is not

possible.

The following statement applies to these products:

 EX6100

 EX6200

 VEGN2200

 WN370

The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or

 EX6200

 VEGN2200

 WN370

 WN2500RP

The device operates in 5.15~5/25GHz frequency range. It is restricted in indoor environment only.

Non-DFS Warning

NETGEAR non-DFS products do not support operation in the 5600-5650MHz band. The firmware on the device

restricts the operation in this frequency band and does not utilize the channels in this band.

NETGEAR non-DFS products will not permit operations on channels 120–132 for 11a and 11n/a, which overlap the

93 of the National Electrical Code, which provides guidelines for proper grounding and, in particular, specifies that the

Coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as

possible.

Canadian Department of Communications Radio Interference

Regulations

The information in this section applies to products bearing the statements:.

“This digital apparatus does not exceed the Class B limits for radio-noise emissions from digital apparatus

as set out in the Radio Interference Regulations of the Canadian Department of Communications.”

“Cet appareil numérique ne dépasse pas les limites de la classe B pour les émissions radio bruit des

appareils numériques, tel qu'énoncé dans le Règlement sur le brouillage radioélectrique du ministère des

Communications du Canada.”

CAN ICES-3 (B)/NMB-3(B)

Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage

préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités.

Sélection d'autres canaux n'est pas possible.

This device complies with the requirements in China for Safety and Quality

此为A级产品，在生活环境该产品可能会造成无线电干扰，在这种情况下可能需

要用户对其干扰采取确实可行的措施。

Australia and New Zealand Notices

The information in this section applies to products bearing the Australia C-Tick and A-Tick Compulsory Marks:

This device equipment complies with the Australian and New Zealand regulatory approvals requirements.

Warning

NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference

in which case the user may be required to take adequate measures.

Powerline Device Safety Information

 Only power cords and allowed to be inserted into the filtered AC socket; no other equipment with a direct

plug-in is allowed. Power cords needs to be a maximum of 1m long and a minimum of 0.75mm² of cross-

sectional area.

 Do not plug devices into the Powerline Pass Thru Adapter filtered AC outlet that exceed the product ratings.

The output voltage of the filtered AC outlet is the same as the power outlet that the Powerline Pass Thru

Adapter is plugged into. To help avoid damaging your system, be sure that the attached devices are

electrically rated to operate with the power available in your location.

 If the input AC voltage is less than 100 Vac, the device plugged into the filtered AC socket of the Powerline

Pass Thru Adapter might not perform as well as expected.

 DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an attached power strip.

compartments.

 Use the product only with approved equipment.

 Allow the products to cool before removing covers or touching internal components.

supply is set o match the power available at your location:

 The peripheral power cables are equipped with three-prong plugs to help ensure proper grounding. Do not

use adapter plugs or remove the grounding prong from a cable.

This information applies to the installation of all NETGEAR rack mount products

 Ambient operating temperature. If the switch is installed in a closed or multiunit rack assembly, the

ambient operating temperature of the rack environment might be greater than the ambient temperature of

the room. Therefore, consider installing the equipment in an environment compatible with the maximum

rated ambient temperature.

 Reduced airflow. Mount the equipment into a rack so that the amount of airflow required for safe operation

is not compromised.

 Mechanical loading. Mount the equipment into a rack so that a hazardous condition does not arise due to

uneven mechanical loading.