Netgear orporated 14200279 Netgear Base Station User Manual

Netgear Incorporated Netgear Base Station

Contents

User Manual

1Quick Start GuideBeta
2WelcomeThank you for choosing Arlo. Getting started is easy.
3What’s IncludedBase station Base station power adapterLithium 123 batteries(number of batteries varies with number of cameras)Ethernet cable Mountingscrews100% wireless camera(s)Magnetic wall mounts
41Get the AppFor the best experience, download the Arlo app for your smartphone by scanning the QR code below or searching for “Arlo” in the app store. Available AFTER betahttps://arlo.netgear.com/hmsweb/users/cs/getApp
5Connect Your Base Station to the InternetConnect the base station to your router using an Ethernet cable.Connect the AC adapter to your base station and plug it in.2
6Turn the base station on by pressing the On-O button.The power LED and Internet LED on the front of the base station turn green in about two minutes.(If this doesn’t happen, visit http://support.netgear.com for troubleshooting tips.)
7Get an AccountLaunch the app from your smartphone and click the New System Setup button. Follow the on-screen instructions.3Available AFTER betaOr from a computer, visit https://arlo.netgear.com/ and follow the on-screen instructions.
8Set Up and Sync Your CamerasInsert batteries• Unlock the battery compartment by sliding and holding the latch.• Slide the battery door back and lift it to open the compartment.• Insert the batteries as shown and close the battery door.4
9Sync your cameras with the base stationBring the camera within one to three feet of the base station.1’ - 3’
10Press the Sync button on the side of the base station.Wait for the sync status LED to blink green.Press the Sync button on top of the camera. Cameras must be synced one at a time. Sync your cameras with the base station (cont’d)
11A blue LED on the camera blinks rapidly to confirm sync. The camera is ready for viewing. Note: The LED blinks amber if the sync in not successful. You must repeat the sync process again.The camera LED on the base station turns solid green after the camera is synced. Repeat these steps for each camera.Note: If the sync procedure is not completed within 60 seconds, press the Sync button on the base station and try again.
12Place or Mount Your CamerasLocate a spot for your cameraYou can place your camera on a shelf or other flat surface, or you can mount it to the wall.5Tip: Use the Arlo app in Position mode (found in Camera Settings) to help aim the camera.
13To mount your camera to the wall:Fasten the mounting screw into the wall,and hang the magnetic mount from the screw. If you’re mounting the camera to drywall, be sure to use the drywall plastic anchors that are provided.Tip: You can also use double-sided tape instead of screws.
14You’re Done!Congratulations! Your Arlo System is set up and ready to go.To view useful tutorial videos, find troubleshooting tips, or get support, visit http://support.netgear.com or call (US only) 1-888-NETGEAR.
15Base Station LED GuideBlinking green A firmware update is in progress. DO NOT TURN OFF BASE STATION OR CAMERAS.GreenCameras are connected to the base station.Blinking green The base station is sending data over the Internet.GreenThe base station is powered on.Blinking green The base station is attempting to sync with a camera.GreenThe base station is connected to the Internet.AmberThe base station is booting up.OThe base station is powered o.Blinking amberA camera is too far from the base station. Signal strength is weak.ONo cameras detected..AmberThe base station is connected to the router but does not have an Internet connection.OThe base station is not connected to your router.Power CameraInternetReserved for upcoming features
16©2014 NETGEAR, Inc. NETGEAR, the NETGEAR Logo, and Arlo are trademarks of NETGEAR, Inc. For regulatory compliance information, visit http://www.netgear.com/about/regulatory/350 East Plumeria DriveSan Jose, CA 95134, USAOctober 2014 BETA

Navigation menu