Netgear orporated DC112A AirCard Smart Cradle User Manual rev

Download:
Mirror Download [FCC.gov]
Document ID	3223682
Application ID	Drq8pQP1zbDFAfOKiD38rQ==
Document Description	Users Manual_rev
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	95.11kB (1188902 bits)
Date Submitted	2016-12-09 00:00:00
Date Available	2017-06-07 00:00:00
Creation Date	2016-11-30 19:16:39
Producing Software	PDFium
Document Lastmod	2016-12-09 15:40:25
Document Title	Users Manual_rev
Document Creator	PDFium

Quick Start
Attach the External WiFi Antennas
For the best WiFi performance, attach both antennas.
3. Slide the antenna covers on the bottom of the mobile hotspot to the open
position.
4. Dock the mobile hotspot in the Smart Cradle.
1. Align the antennas with the antenna posts on the cradle.
AirCard® Smart Cradle
Model DC112A
The AirCard Smart Cradle allows you to transform your AirCard mobile
hotspot into a powerful LTE router by combining the benefits of a home
router and a Wi-Fi signal booster. It charges your mobile hotspot battery,
boosts its 4G/3G signal, extends WiFi coverage, and expands your mobile
hotspot connection to both wired and wireless devices. This cradle can also
be used as a standalone 802.11ac Dual-Band WiFi router.
Package Contents
2. Attach the antennas on the threaded antenna posts, ensuring that the
connection is secure.
3. Adjust the antenna positions so that they point straight up.
Install the AirCard Smart Cradle
1. Place the Smart Cradle in your preferred location.
2. Connect the cradle’s power adapter and plug it into an electrical outlet.
External WiFi antennas (2)
Power On/Off button
Power input
AirCard Smart Cradle
Power adapter (appearance
varies by region or country)
The Power LED
lights green within one minute. If the Power LED
does not light, press the Power On/Off button on the rear panel of the
cradle.
5. Check the Smart Cradle’s Internet LED
The Smart Cradle detects your mobile hotspot’s Internet connection, the
Internet LED lights green, and the cradle uses the mobile hotspot’s Internet
connection. The mobile hotspot must have active Internet service.
When your mobile hotspot detects that it is docked, the mobile hotspot
LCD and home page indicate that it is docked in the cradle. The mobile
hotspot uses the cradle’s more powerful 3G/4G antennas for better
network coverage and charges itself through the cradle. The mobile hotspot
disables its WiFi signal so that you can connect to the Smart Cradle’s
stronger WiFi signal.
NOTE: Some mobile hotspots require a firmware update before they
automatically disable WiFi when docked. If your mobile hotspot broadcasts its
WiFi signal when docked, manually set up your mobile hotspot to disable WiFi.
See the mobile hotspot user guide for more information.
6. On your computer or WiFi device, find and connect to the WiFi network
name on the cradle label.
Log In to the AirCard Smart Cradle
Front Panel LEDs
You can log in to the Smart Cradle to view or change its settings.
LED
Description
1. Connect a computer to the cradle:
• For a WiFi connection, on your computer or WiFi device, find and
connect to the WiFi network name on the cradle label.
• For a wired connection, use an Ethernet cable to connect a
computer to an Ethernet LAN port on the rear panel of the cradle.
Power
• Solid amber. The cradle is booting.
2. Launch a web browser.
3. In the address field of the browser, enter http://netgear.cradle.
A login prompt displays.
The Home screen displays.
The AirCard Smart Cradle can also be used for:
• Use the mobile hotspot’s Internet connection as a backup for your
regular Internet connection.
• Use the cradle to extend WiFi coverage for another WiFi network.
• Share a hard drive or printer using ReadySHARE USB Storage Access and
ReadySHARE Printer.
• Share media using DLNA server or ReadySHARE.
• Solid green. The cradle is powered on and ready.
For the current EU Declaration of Conformity, visit
http://support.netgear.com/app/answers/detail/a_id/11621/.
• Solid green. The USB device is connected and ready.
• Solid red. A USB device is connected but unrecognized.
• Off. No USB device is connected, or someone clicked the
Safely Remove Hardware button and it is safe to remove the
attached USB device.
Internet
• Solid green. The Internet connection is ready.
• Solid amber. The cradle is connected to the Internet.
For regulatory compliance information, visit
http://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
To avoid potential WiFi signal interference, do not put the cradle close to
reflective or metal surfaces, such as mirrors, metal file cabinets, or stainless
steel counter tops. Do not put the cradle near electrical equipment or appliance
such as microwave ovens.
• Off. The cradle is not connected to the Internet.
Ethernet LAN (4)
• Solid. A powered-on device is connected to this port.
• Off. No device is connected to this port.
2.4 GHz
• Solid green. The 2.4 GHz WiFi radio is operating.
• Blinking. The cradle is in WPS mode.
• Off. The WiFi radio is off.
Undock the Mobile Hotspot
5 GHz
Lift the mobile hotspot from the AirCard Smart Cradle. If it is difficult to
remove, gently wiggle the mobile hotspot from side to side. When you
remove the mobile hotspot, the AirCard Smart Cradle loses its LTE Internet
connection, but it continues to work as a WiFi router. The mobile hotspot
enables its own WiFi again so you can connect to the mobile hotspot WiFi.
October 2014
Contact NETGEAR at 1 800 17 22 44 for technical support.
• Off. Power is not supplied to the cradle.
4. Enter admin for the user name and enter the password.
The default password is password.
For information about Smart Cradle features, see the Smart Cradle user manual,
available at http://downloadcenter.netgear.com/.
• Blinking amber. The firmware is upgrading, or someone
pressed the Reset button.
• Blinking green. The firmware is corrupted. Contact your
Internet service provider for techncial support.
USB
Support
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
• Solid green. The 5 GHz WiFi radio is operating.
• Blinking. The cradle is in WPS mode.
• Off. The WiFi radio is off.
© NETGEAR, Inc. NETGEAR, the NETGEAR Logo, ReadySHARE, and AirCard, are trademarks of NETGEAR,
Inc. Information is subject to change without notice.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
‐
Reorient or relocate the receiving antenna.
‐
Increase the separation between the equipment and receiver.
‐
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
‐
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co‐located or operating in conjunction with any other antenna or
transmitter.
For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment. This
device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Radiation Exposure Statement:
To comply with FCC RF Exposure Limits set forth for an uncontrolled environment, the product must
be installed and operated with a minimum separation distance (between nearby person(s) and
radiating antenna) according to the following scenarios:
1. 20cm minimum when the product is operated alone without co‐transmitting with a plug‐in mobile
hotspot device.
2. 48cm minimum when the product is operated with a plug‐in mobile hotspot device which has
maximum output power in each certificate license band.
3. For co‐transmission scenario which is not covered above, please consult the RF technician or device
supplier.
Industry Canada statement:
This device complies with ISED’s licence‐exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Caution :
(i) the device for operation in the band 5150‐5250 MHz is only for indoor use to reduce the potential
for harmful interference to co‐channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250‐5350 MHz and 5470‐5725
MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the band 5725‐5850 MHz shall be such that
the equipment still complies with the e.i.r.p. limits specified for point‐to‐point and non‐point‐to‐point
operation as appropriate; and
(iv) the worst‐case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask
requirement set forth in Section 6.2.2(3) shall be clearly indicated.
(v) Users should also be advised that high‐power radars are allocated as primary users (i.e. priority
users) of the bands 5250‐5350 MHz and 5650‐5850 MHz and that these radars could cause
interference and/or damage to LE‐LAN devices.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les
restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5150‐5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 à 5 350 MHz et
de 5470 à 5725 MHz doit être conforme à la limite de la p.i.r.e;
(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz)
doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et l’exploitation
non point à point, selon le cas;
(iv) les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable
au masque d’élévation, et énoncée à la section 6.2.2 3), doivent être clairement indiqués.
(v) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance
sont désignés utilisateurs principaux (c.‐à‐d., qu’ils ont la priorité) pour les bandes 5250‐5350 MHz et
5650‐5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs
LAN‐EL.
Radiation Exposure Statement:
To comply with ISED RF Exposure Limits set forth for an uncontrolled environment, the product must
be installed and operated with a minimum separation distance (between nearby person(s) and
radiating antenna) according to the following scenarios:
1. 24cm minimum when the product is operated alone without co‐transmitting with a plug‐in mobile
hotspot device.
2. 67cm minimum when the product is operated with a plug‐in mobile hotspot device which has
maximum output power in each certificate license band.
3. For co‐transmission scenario which is not covered above, please consult the RF technician or device
supplier.
AVERTISSEMENT DE SECURITE CONCERNANT LES EXPOSITIONS AUX FREQUENCES RADIO
Pour etre conforme aux limites d’exposition aux frequences radio ISED etablies pour un
environnement non controle (utilisation par le grand public), l’equipement doit etre installe et utilise
en laissant une distance de separation de securite (entre la ou les personnes presentes dans le
perimetre et l’antenne d’emission) selon les cas suivants :
1.
24cm minimum lorsque le produit est utilisé seul sans co‐transmission avec un plug‐in mobile
hotspot dispositif.
2.
67cm minimum lorsque le produit est exploité avec un dispositif de point d'accès mobile
enfichable qui a une puissance de sortie maximale dans chaque bande de licence de certificat.
3.
Dans des cas de co‐transmission non mentionnes ci‐dessus, merci de bien vouloir consulter un
technicien radio qualifie ou directement le fabricant de l’appareil.
This radio transmitter (IC: 4054A‐DC112A/ Model: DC112A) has been approved by ISED to operate
with the antenna type listed below with maximum permissible gain indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Le présent émetteur radio(IC: 4054A‐DC112A/ Model: DC112A) a été approuvé par ISED pour
fonctionner avec les types d'antenne énumérés ci‐dessous et ayant un gain admissible maximal. Les
types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
Antenna
Brand
Gain(dBi)
Master
2.48
2400~2500 MHz
2.96
5150~5850 MHz
98619PRSX006
Wave
Antenna
Connecter
Type
Type
Dipole
R-SMA
Frequency range
Model

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2016:11:30 19:16:39Z
Creator Tool                    : PDFium
Modify Date                     : 2016:12:09 15:40:25+08:00
Metadata Date                   : 2016:12:09 15:40:25+08:00
Producer                        : PDFium
Format                          : application/pdf
Document ID                     : uuid:a3381424-73cc-4646-a86b-ce9cd8482689
Instance ID                     : uuid:54c50abf-a8b9-43d5-9377-b2da376cfe3c
Has XFA                         : No
Page Count                      : 6
Creator                         : PDFium

EXIF Metadata provided by EXIF.tools