Netgear orporated HE102 Wireless Access Point Module User Manual HE102 Users Guide 1 2

Netgear Incorporated Wireless Access Point Module HE102 Users Guide 1 2

UserManual.wiki >

Netgear orporated >

HE102 User Manual

Manual

Preliminary Access Point User’s Guide • Page 1 802.11a Wireless Access Point Model HE102 User’s Guide Rev 1.2.11

Preliminary Access Point User’s Guide • Page 3 Table of Contents 1 INTRODUCTION..................................................................................................... 4 1.1 SCOPE .................................................................................................................. 4 1.2 FEATURES ............................................................................................................ 4 2 GETTING TO KNOW THE MODEL HE102 ACCESS POINT........................ 5 2.1 FRONT VIEW ........................................................................................................ 5 2.2 REAR VIEW .......................................................................................................... 6 3 AP NETWORK ATTACHMENT AND CONFIGURATION ............................. 8 3.1 AP NETWORK CONFIGURATION AND NETWORK BOOT........................................ 8 3.2 CONFIGURING THE AP THROUGH WEB BROWSER.............................................. 11 APPENDIX A—AP WEB SERVER ............................................................................. 16 INTRODUCTION .............................................................................................................. 16 ACCESSING THE AP WEB SERVER ................................................................................. 16 SETUP ............................................................................................................................ 18 WEP .............................................................................................................................. 20

Preliminary Page 4 • Access point User’s Guide 1 Introduction 1.1 Scope The intent of this document is to familiarize you with the NETGEAR Model HE102 Access Point (AP), its physical characteristics, setup, configuration, and usage. 1.2 Features The Model HE102 Access Point is an IEEE 802.11a AP supporting up to 60 IEEE 802.11a station associations including the AP itself. Rates of 6 to 54 Mbps are supported in standard IEEE 802.11a mode, and 12 to 72 Mbps in turbo mode. All transmission rates are supported across the lower and middle bands of the 5 GHz spectrum(5.15 to 5.35 GHz).

Preliminary Access Point User’s Guide • Page 5 2 Getting to Know the Model HE102 Access Point 2.1 Front View The Model HE102 Access Point (AP) has 3 LED’s, and a pair of side-mounted antennas that rotate 180° for alternative reception positioning and compact packaging. Table 1 – LED Functionality LED 1 Description Off No Power On Power On and Ready for Operation Blink Power On but Not Ready for Operation – at initial power on or reset, this indicates self-test or software loading; at other times, this indicates a system fault LED 1 (Power Status) LED 2 (Ethernet Link) LED 3 (Wireless Link)

Preliminary Page 6 • Access point User’s Guide LED 2 Description Off No Ethernet Link Detected Green On 100 Mbps Link Detected but No Activity Green Blink 100 Mbps Link Activity – blink rate is proportional to activity Amber On 10 Mbps Link Detected but No Activity Amber Blink 10 Mbps Link Activity – blink rate is proportional to activity LED 3 Description Off Wireless Link Disabled Very Slow Blink Looking for Network Association Slow Blink Associated with Network but No Activity Fast Blink Associated with Network – blink rate is proportional to activity 2.2 Rear View The rear panel of the AP has a console interface, a RJ-45 Ethernet jack, a restore-to-default button, and a power supply connector, RJ-45 Ethernet Jack Restore to Default Button Power Supply Connector

Preliminary Access Point User’s Guide • Page 7 • The console connector is only used for system configuration during manufacturing process and should not be connected. • The RJ-45 Ethernet jack is provided for 10/100 Mbps connectivity to a wired Ethernet LAN. The Ethernet jack is wired for direct connection to a Ethernet hub or switch. • The restore to default push button is to allow the Access Point to be reset back to the factory default condition in the event that the Access Point is no longer accessible or controllable through its web-based interface. • A 3.3 V power supply is provided and is plugged into the power supply connector of the AP.

Preliminary Page 8 • Access point User’s Guide 3 AP Network Attachment and Configuration 3.1 AP Network Configuration and Network Boot Figure 1 shows an example connection of the AP to a Host PC (HPC). Follow these steps to establish the physical connections: 1. Connect the AP Ethernet port to the HPC Ethernet card through the Ethernet hub/switch or an Ethernet crossover cable. An Ethernet switch/hub or crossover cable is not included. 2. Plug in the 3.3 V power supply adapter (provided by NETGEAR) to the AP power supply connector. Figure 1 – Connection Between AP and Host PC At this point, the Windows-based HPC needs the following configuration steps in order to control the AP: 1. From the Start menu, choose Settings and open the Network and Dial-up Connections window. 2. Right-click on the Local Area Network icon in the window, which belongs to the Ethernet controller that is connected to the AP and select Properties. Host PC (HPC) Ethernet Port Ethernet Cable HE102 Access Point (AP) Ethernet Hub/Switch Ethernet Port Power Power Supply Ethernet Cable

Preliminary Access Point User’s Guide • Page 9 3. Within the Local Area Connection Properties window, choose Internet Protocol (TCP/IP) and click Properties.

Preliminary Page 10 • Access point User’s Guide 4. Configure the IP address for the Ethernet connection in the Internet Protocol (TCP/IP) Properties window. Click OK to continue, and close Local Area Connection Properties. Note that this IP address is used by the HPC to access the AP through the web-based interface via the Ethernet connection.

Preliminary Access Point User’s Guide • Page 11 3.2 Configuring the AP through Web Browser The following procedures show the steps to configure the channel frequency and SSID using a web browser: 1. Launch a web browser (Netscape Navigator or Internet Explorer are examples of commonly used web browsers) from the Host PC or other PC on the same IP subnet as the AP, and enter the IP address that is assigned to the AP as the URL. This is the “inet on ethernet (e)” value specified during the configuration step in Section 3.1.1 or Section 3.1.2. The Access Point Web Server page appears.

Preliminary Page 12 • Access point User’s Guide 2. Click Setup. A dialog box appears that requests login authorization. When prompted, enter the following information to log in: Log in: Admin Password: 5up Click OK to complete the login process. 3. After the Setup menu loads, enter the SSID and IEEE Radio Channel that the stations (STAs) are associating in Infrastructure mode. Click Apply to commit the changes. At this time you can also change other settings. Refer to Appendix A for detailed information about each configuration option. Note that the radio channel is specified using the IEEE 802.11a standard. For example, channel 48 is the equivalent of 5.240 GHz. The formula below shows how the channel number is derived: Channel Number = Channel Frequency (in MHz) – 5000 MHz 5 MHz

Preliminary Access Point User’s Guide • Page 13 Another new feature added to the AP firmware is the ability to control Transmit Power parameter. This feature can be used to decrease the transmit power, and therefore, reduce the range of the radio. In this operation mode, more than one AP with the same channel frequency can exist in the same location (as long as the ranges of these APs can cover are not overlapped each other).

Preliminary Page 14 • Access point User’s Guide 4. Optionally, you can also set up Wired Equivalent Privacy (WEP) for security purposes. To set up WEP, click WEP and the configuration screen appears. Refer to Appendix A for a detailed explanation of the WEP configuration options. Click Apply to save the settings. Note that the Un-Encrypted Frames filter option (previously available in release 1.0) is now removed.

Preliminary Access Point User’s Guide • Page 16 Appendix A—AP Web Server Introduction You can configure the AP through a web browser interface to the AP web server. The web server resides in the AP and is accessible from any STA that is connected to the AP Infrastructure network. Accessing the AP Web Server To access the AP web server, use the IP address of the AP as the URL address, for example http://192.168.1.1. The web server home page contains several hyperlinks that provide viewing of the system information, status of the AP and associated stations, and configuration parameters of the AP. On the initial entry into the AP web server (click on hyperlink) a popup window appears prompting for a username and password. Enter the username and password, and click “OK” to enter the AP web server. If you want to receive warning messages when configuring the AP, enable JavaScript on the web browser. Otherwise, no warnings are issued.

Preliminary Access Point User’s Guide • Page 17

Preliminary Access Point User’s Guide • Page 18 Setup Click the Setup hyperlink from the AP Web Server home page to change AP configuration parameters. This page displays the current configuration of the AP. If you modify the configuration parameters, you must click Apply to save the changes. The new configuration is not in effect until you reboot the AP. Click Reboot to reboot the AP. The web browser loses connectivity with the AP web server as the AP reboots. To establish a network connection to the rebooted AP, wait until the AP has completed rebooting, and then navigate to the web server home page (by clicking the Home hyperlink) to resume communication with the AP web server.

Preliminary Access Point User’s Guide • Page 19

Preliminary Access Point User’s Guide • Page 20 WEP Click the WEP hyperlink to configure the WEP keys. The configurable options of the WEP page provide the ability to: • Enable and disable WEP • Select the default shared WEP key • Specify the shared and unique WEP keys • Enable, disable, restrict, and configure the ACL Refer to the following table for examples of WEP configurations on the AP and the STA. WEP: Disable WEP is disabled. Any STA can access to the network WEP: Enable ACL Shared Key ACL MAC address Key Map Permission WEP No Disable No No No WEP is disabled. Any STA can access to the network Yes Disable No No No Only STA with matched shared key can access to the network Yes Enable Yes No Allow 1. STA with matched MAC ID can access to the network 2. Any STAs with matched shared key are also allowed to access to the network Yes Enable No Unique key Allow 1. STA with matched unique key can access to the network 2. Any STAs with matched shared key are also allowed to access to the network Yes Enable Yes Unique key Allow 1. STA with matched MAC ID and matched unique key can access to the network 2. Any STAs with matched shared key are also allowed to access to the network x Enable Yes No Deny STA with the matched MAC ID is blocked from accessing the network x Enable No Unique key Deny STA with the matched unique key is blocked from accessing the network x Enable Yes Unique key Deny STA with the matched MAC ID and unique key is blocked from accessing the network

Preliminary Access Point User’s Guide • Page 21 Yes Strict x x x 1. Only STA with MAC ID and/or unique key matched to the setup in ACL can access to the network. 2. The STAs with only shared key are blocked from accessing the network. After entering or modifying the WEP configuration, you must click Apply to save the changes.

Preliminary Access Point User’s Guide • Page 22 To view the configuration of a unique key, use the pull down menu to select the unique key ID, select Read inside the Unique Key frame, and then click Apply to view the unique key. In this example, unique key ID 6 is selected. The next example shows the results.

Preliminary Access Point User’s Guide • Page 23

Preliminary Access Point User’s Guide • Page 24 To make changes, select Write, enter the key changes, select the appropriate key size, select a unique key ID, and click Apply. Use the same procedure to add new unique keys. Note that the unique key ID starts from 5 and ends at 64. A total of 60 unique keys can be stored in the AP.

Preliminary Access Point User’s Guide • Page 25 To delete a unique key, select Delete, use the pull down menu to select the unique key ID that contains the unique key you want to delete, and click Apply.

Preliminary Access Point User’s Guide • Page 26 To view the ACL list, select Read inside the ACL frame, enter the ACL ID to be viewed, and click Apply. In this example, ACL ID 1 is selected and displayed, and specifies that MAC address 00:3f:73:00:00:01 is allowed access.

Preliminary Access Point User’s Guide • Page 27 In this example, ACL ID 3 is selected and displayed, and specifies that MAC address 11:11:11:11:11:11 is allowed access with unique key 6.

Preliminary Access Point User’s Guide • Page 28 To add a new ACL entry, select Write, enter the new MAC address, enter key ID (if needed), select either Deny or Allow, and click Apply to save the changes. In this example, the new ACL entry has the MAC address 08:00:20:ac:37:51 using shared key 1 to allow access. The next example shows that the changes are accepted and ACL ID 4 (the next available ACL ID) is automatically assigned.

Preliminary Access Point User’s Guide • Page 29

Preliminary Access Point User’s Guide • Page 30 To delete an ACL entry, select Delete, enter the ACL ID to be deleted, and click Apply. In this example, ACL ID 2 is deleted.

Navigation menu