Netgear Wndap660 Reference Manual ProSafe Premium 3 X Dual Band Wireless N Access Point

2015-03-12

• ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP660
• Contents
• 1. Introduction
  • About the ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP660
  • What Is in the Box?
  • System Requirements
  • Key Features and Standards
    • Supported Standards and Conventions
    • Key Features
    • 802.11b/g/n and 802.11a/n Standards–Based Wireless Networking
    • Autosensing Ethernet Connections with Auto Uplink
  • Hardware Description
    • Top Panel
    • Rear Panel
    • Bottom Panel with Product Label
  • Register the Wireless Access Point
• 2. Installation and Basic Configuration
  • What You Need Before You Begin
    • Wireless Equipment Placement and Range Guidelines
    • Ethernet Cabling Requirements
    • LAN Configuration Requirements
    • Hardware Requirements for Computers on Your LAN
    • Operating Frequency (Channel) Guidelines
    • Requirements for Entering IP Addresses
  • Install and Configure the Wireless Access Point
    • Connect the Wireless Access Point to a Computer
    • Log In to the Wireless Access Point
    • Configure Basic General System Settings and Time Settings
    • Configure the IPv4 Settings
    • Configure the Optional DHCPv4 Server
    • Configure the Basic Wireless Settings
  • Test Basic Wireless Connectivity
  • Mount the Wireless Access Point
    • Ceiling Installation
    • Wall Installation
    • Desk Installation
• 3. Wireless Configuration and Security
  • Wireless Data Security Options
  • Security Profiles
    • Before You Change the SSID, WEP, and WPA Settings
    • Configure and Enable Security Profiles
  • Configure RADIUS Server Settings
  • Restrict Wireless Access by MAC Address
  • Schedule the Wireless Radios to Be Turned Off
  • Configure Basic Wireless Quality of Service
• 4. Management and Monitoring
  • Enable Remote Management
    • SNMP Management
    • Secure Shell and Telnet Management
  • Upgrade the Wireless Access Point Software
    • Web Browser Upgrade Procedure
    • TFTP Server Upgrade Procedure
  • Manage the Configuration File or Reset to Factory Defaults
    • Save the Configuration
    • Restore the Configuration
    • Restore the Wireless Access Point to the Factory Default Settings
    • Reboot the Wireless Access Point without Restoring the Default Configuration
  • Change the Administrator Password
  • Manage User Accounts
  • Enable the Syslog Server
  • Monitor the Wireless Access Point
    • View System Information
    • Monitor Wireless Stations
    • View the Activity Log
    • Traffic Statistics
  • Enable Rogue AP Detection and Monitor Access Points
    • Enable and Configure Rogue AP Detection
    • View and Save Access Point Lists
  • Configure Wireless Intrusion Detection and Prevention
    • Configure Wireless Intrusion Detection and Prevention Policy Settings
    • Configure Wireless Intrusion Detection and Prevention Mail Settings
    • Monitor Traps, Counters, and Ad Hoc Networks
• 5. Advanced Configuration
  • Configure IPv6 Settings and Optional DHCPv6 Server Settings
    • Configure the IPv6 Settings
    • Configure the Optional DHCPv6 Server
  • Configure Spanning Tree Protocol, 802.1Q VLAN, and Link Layer Discovery Protocol
    • Configure STP and VLANs
    • Configure Ethernet LLDP
  • Configure Hotspot Settings
  • Configure Advanced Wireless Settings
  • Configure Advanced Quality of Service Settings
  • Configure Quality of Service Policies
  • Configure Wireless Bridging
    • Configure a Point-to-Point Wireless Network
    • Configure a Point-to-Multipoint Wireless Network
    • Configure the Wireless Access Point to Repeat the Wireless Signal Using Point-to-Multipoint Bridge Mode
• 6. Troubleshooting
  • Basic Functioning
    • Verify the Correct Sequence of Events at Startup
    • No LEDs Are Lit on the Wireless Access Point
    • The Active LED or the LAN LED Is Not Lit
    • The WLAN LED Does Not Light Up
  • You Cannot Access the Internet or the LAN from a Wireless-Capable Computer
  • You Cannot Configure the Wireless Access Point from a Browser
  • When You Enter a URL or IP Address a Time-Out Error Occurs
  • Troubleshoot a TCP/IP Network Using the Ping Utility
    • Test the LAN Path to Your Wireless Access Point
    • Test the Path from Your Computer to a Remote Device
  • Problems with Date and Time
  • Use the Packet Capture Tool
• A. Supplemental Information
  • Technical Specifications
  • Factory Default Settings
• B. Command-Line Reference
• C. Notification of Compliance
• Index