Neutrik XPR Digital Wireless Audio Network User Manual part 1

Neutrik AG Digital Wireless Audio Network part 1

User Manual part 1

User Manual
Applies to XIRIUM PRO CANADA, AUSTRALIA, and
NEW ZEALAND devices
2
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Imprint
Subject to change due to technical advances! This user manual corresponds to the level of
technology at the time the product was delivered and not the current stage of development at
Neutrik.
If any pages or sections of this user manual are missing, please contact the manufacturer at the
address listed below.
Copyright
This user manual is protected by copyright. The user manual must not be duplicated, reproduced,
microlmed or translated, or converted to be saved and processed in EDP systems, neither as
excerpts nor in full, without the express written authorization of Neutrik.
Copyright by: © Neutrik® AG
Document identification
Document No: BDA 470
Version: 2017/03
cThis user manual applies to firmware 3.0 and app version 3.0!
Language: English
Original language: German
Each user manual in a different language is a translation of the operating manual in German.
Manufacturer
Neutrik® AG
Im alten Riet 143
9494 Schaan
Liechtenstein
T: +423 2372424
F: +423 2325393
E: neutrik@neutrik.com
www.neutrik.com
3
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Table of contents
1 About this document ..............................................4
1.1 Signicance of the user manual .............................4
1.2 Designation ..........................................................4
1.3 Explanation of symbols .........................................5
1.3.1 Symbols in illustrations ....................................5
1.4 Target group .........................................................5
2 Safety ........................................................................6
2.1 Warning information and signal words ..................6
2.2 Warning symbols ..................................................6
2.3 Important regulatory notes ...................................7
2.3.1 Radio frequency radiation exposure informa-
tion .........................................................................8
2.4 Important safety instructions .................................8
2.5 Proper use ..........................................................10
2.6 Foreseeable improper use ................................... 10
3 Components and accessories ................................ 11
3.1 XIRIUM PRO components .................................... 11
4 Description of product ..........................................13
4.1 X IRIUM PRO base station ..................................... 13
4.2 Modules ............................................................. 14
4.2.1 TX modules ...................................................14
4.2.2 RX modules .................................................. 14
4.3 XIRIUM PRO app ................................................. 15
4.3.1 Overview of operation elements .................... 15
4.3.2 Links/Overview page .....................................17
4.3.3 Edit page ......................................................18
4.3.4 Settings page ................................................21
4.3.5 Help page ..................................................... 22
4.4 Getting started ...................................................23
4.4.1 App ..............................................................24
4.4.2 Repeater ....................................................... 24
4.4.3 Signal quality bar ..........................................24
4.4.4 Transmission power ......................................25
4.4.5 XROC mode .................................................26
4.4.6 Antennas ......................................................26
4.4.7 Line-of-sight and redundant RF path .............28
4.4.8 Antenna height + distance ............................ 28
4.4.9 Line-of-sight and redundant RF path .............30
4.5 Selecting transmission channels ..........................31
4.5.1 Automatic selection of transmission channels ...31
4.5.2 Manual selection of transmission channels ....31
5 Operation ...............................................................32
5.1 Setting devices into operation .............................32
5.2 Setting up the transmission path ......................... 33
5.3 Installing and starting the app .............................34
5.4 Connecting devices with the app ........................34
5.4.1 Connecting devices in stand-alone mode ......34
5.4.2 Connecting devices in network mode ...........35
5.5 Arranging the radio transmission path .................38
5.6 Conguring the device parameters ...................... 39
5.7 Editing system settings ........................................ 43
5.7.1 System reset ..................................................43
5.7.2 Advanced Mode ...........................................43
5.8 Setting up and mounting the XIRIUM PRO system .. 44
5.8.1 Positioning the devices ..................................44
5.8.2 Positioning the repeater ................................ 45
5.8.3 Systems with several transmitters ..................45
5.8.4 Fastening and securing XIRIUM PRO devices ... 46
5.9 Upgrading rmware ............................................47
5.9.1 Installing the XIRIUM PRO Firmware Upgrade
Manager ................................................................47
5.9.2 Executing a rmware upgrading ...................48
5.9.3 Uninstalling the XIRIUM PRO Firmware Upgrade
Manager ................................................................ 50
6 Troubleshooting.....................................................51
7 After operation ......................................................52
7.1 Dismounting devices ............................................52
7.2 Transporting ........................................................52
7.3 Storage ...............................................................52
7.4 Cleaning and care ...............................................52
7.5 Maintenance and repair .......................................52
7.6 Dispo sal ..............................................................53
8 Appendix ................................................................54
8.1 Integrating DANTE ..............................................54
8.1.1 Introduction to DANTETM ...............................54
8.1.2 Enabling a DANTETM link ................................ 54
8.2 Access point settings ..........................................55
8.2.1 Recommended settings .................................55
8.2.2 XIRIUM PRO basic kit with access point .........55
8.3 Technical specications .......................................56
4
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
About this document
1 About this document
This user manual provides an overview of the necessary operation steps and settings of the product.
1.1 Significance of the user manual
This user manual is an integral component of the product and part of the product's safety
concept.
cMake sure that all persons who work with the product have fully read and also
understood this user manual.
cObserve all instructions exactly, especially the safety instructions.
This user manual contains important information for operating and maintaining the product
and troubleshooting minor problems safely and properly on your own.
cKeep this user manual in the immediate vicinity of the product so personnel have access
to it at all times.
cPass this user manual on to every user, e.g., by lending it, or to the future owner of the product.
cIf this user manual is lost or damaged, a copy of the operating manual
can be downloaded from the Neutrik's home page (www.neutrik.com).
1.2 Designation
Designation Explanation
XIRIUM PRO System All components:
XIRIUM PRO base stations, XIRIUM PRO modules, cables, plugs, antennas
XIRIUM PRO base
station
XIRIUM PRO TX (transmitter) without module, short TX
XIRIUM PRO RX (receiver) without module, short RX
XIRIUM PRO module Exchangeable module for the XIRIUM PRO base station
XIRIUM PRO device XIRIUM PRO base station with module plugged-in
XROC mode Extreme Ruggedized One Channel mode for a secure connection in
extreme situations.
Peripheral devices All devices which can be connected with each other via the XIRIUM PRO
devices: audio sources (transmitters) and audio sinks (receivers)
Audio source All devices which emit a signal
Audio sink All devices which receive the audio signals, e.g., loudspeakers, audio
systems (ampliers, mixing consoles, etc.)
Transmission path Wireless connection between the XIRIUM PRO devices.
A transmission path consists of 1 TX, 1 repeater (optional) and at least
1 RX.
Network All devices used which are connected to the app via an access point.
5
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
About this document
1.3 Explanation of symbols
In order to make this user manual easier to understand, uniform safety instructions, symbols, terms
and abbreviations were used. The following symbols designate instructions which are not relevant to
safety, yet make it easier to understand the operating manual.
^The preconditions for an action are depicted with this symbol. Complete the specied items
before carrying out the action steps which follow.
cAction steps are designated by this symbol. Carry out the action steps in the order they are
presented.
(The result of the action or the reaction of the product to the action are depicted with this
symbol.
•Lists without a mandatory sequence are presented as a list with this bullet.
1. Numbered listings are displayed in this manner.
(1) Refers to a position in an illustration.
Texts in this color designate elements on the app surface.
Wherever you see this symbol, you will nd useful information for safe, trouble-free operation
of the product.
1.3.1 Symbols in illustrations
Symbol Explanation
Image position
Action steps numbered in an illustration.
Carry out the action steps in the order they are presented.
Only carry out these tasks when using an Apple iPad.
Only carry out these tasks when using an Android tablet.
1.4 Target group
This user manual is directed to sound engineers and professional personnel who have detailed expe-
rience in the sound and event technology.
Personnel who are in training must only work with this device under the supervision of experienced
persons.
1
1
6
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Safety
2 Safety
2.1 Warning information and signal words
Special warning information regarding potential dangers inherent in a particular action are presented
before instructions for an action. The warnings are ranked as follows:
DANGER
Immediate threat of danger!
This type of warning points out a situation which would result in death or severe injuries.
cIf this warning is not heeded, the threat of death or serious injuries is imminent.
WARNING
Possible threat of danger!
This type of warning points out a situation which could result in death or severe injuries.
cIf this warning is not heeded, the threat of death or serious injuries might be imminent.
CAUTION
Possible threat of danger!
This type of warning points out a situation which could result in minor or moderate injuries.
cIf this warning is not heeded, minor injuries may result.
NOTICE
Possible threat of property damage!
This type of warning points out a situation which could result in damage to the device and its
components.
cIf this warning is not heeded, property damage may result.
2.2 Warning symbols
Symbol Warning
General warning
Warning of hearing impairment
Danger of electric shock
7
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Safety
2.3 Important regulatory notes
This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
NOTICE
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS
standards.
Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation.
REMARQUE
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
NOTICE
Changes or modications made to this equipment not expressly approved by Neutrik may void
the FCC and IC authorization to operate this equipment.
NOTICE
This device must be professionally installed.
NOTICE
This radio transmitter (IC: 11536A-XPT / IC: 11536A-XPR) has been approved by Industry Canada
to operate with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated
for that type, are strictly prohibited for use with this device.
Provided antennas:
• NXPA-2-360 (SOA-2456/360/1/0/V; 2 dBi gain)
• NXPA-6-360-25 (ECO6-5500-BLK-RN; 6 dBi gain)
• NXPA-9-360-12.5 (ECO9-5500-BLK-RN; 9 dBi gain)
8
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Safety
2.3.1 Radio frequency radiation exposure information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated with minimum distance of 0,65 ft (20 cm)
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or trans-
mitter.
2.4 Important safety instructions
WARNING
Risk of fire or electric shock!
cTo reduce the risk of re or electric shock, do not expose this device to rain or moisture and do
not set any objects containing liquids on this apparatus.
WARNING
Danger of fire and explosion due to overheated battery!
cDo not expose batteries or battery pack to excessive heat such as re or other heat sources.
•To completely disconnect this apparatus from AC mains, disconnect the power supply cord plug
from the AC socket.
•Keep the mains plug of the power supply cord readily accessible.
Avoid property damage to the XIRIUM PRO devices due to unsuitable operating and environmental
conditions:
•Never immerse in water.
•Protect from strong sunlight.
•Never install the device near heat sources such as radiators, heating units, ovens or stoves.
•Never cover the device, to avoid overheating.
•Protect the device from impact and above all, from falling from poles, stages, tables or furniture.
•Always set up and fasten the device as shown in Section "5.8.4 Fastening and securing XIRIUM
PRO devices" on page 46.
Repair
DANGER
Danger of injury or electric shock and property damage due to improper repair!
The XIRIUM PRO devices do not contain any parts which you can repair yourself. Opening or re-
pairing the devices on your own can lead to severe damage to the devices and electrical shock or
injuries to the operator.
cDo not open the housing of XIRIUM PRO devices under any circumstances.
cDo not exchange any parts yourself.
cOnly have XIRIUM PRO devices repaired by a authorized specialist dealer.
9
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Safety
Electrical connection
DANGER
Danger of electric shock when connecting to or disconnecting from a power grid!
cOnly connect the devices to mains sockets installed by authorized electricians.
cDo not handle the devices with moist or wet hands under any circumstances.
cMake sure the specied mains voltage and mains frequency agree with the values of the
power grid.
cOnly use the delivered power supply cable for connecting to the socket.
cDuring storms or whenever there is a danger of power uctuations, switch off the device and
separate from the power grid.
cEnsure that the power supply cable is not kinked, hung over sharp edges or allowed to contact
hot surfaces during operation.
cDo not use the devices if there is interference or damage to the devices, displays or
accessories.
Information for operation
cEnsure that the ambient conditions specied for XIRIUM PRO are observed during operation.
cDo not use the XIRIUM PRO devices if they are not functioning properly, have fallen or been
damaged, have become wet or if parts of the devices have been immersed in water.
cIf disruptions occur during operation:
Immediately switch off the XIRIUM PRO devices and disconnect them from the power grid.
cDo not operate the XIRIUM PRO devices in environments where ammable or explosive
materials, gases or vapors are present or could occur.
AVERTISSEMENT
Risque d'électrocution!
cPour réduire les risques d'incendie ou d'électrocution, ne pas exposer l'appareil à la pluie ni à
l'humidité et ne pas déposer d'objet contenant du liquide sur cet appareil.
AVERTISSEMENT
Risque d'incendie et d'explosion en cas de surchauffe de la pile!
cLes batteries ou bloc de batteries ne doivent pas être exposées à une chaleur excessive telle
que celle du soleil, feu ou autre source de chaleur similaire.
•Pour déconnecter complètement l’appareil du réseau d’alimentation, déconnecter le cordon
d’alimentation de la prise murale.
•La prise du réseau d’alimentation doit demeurer aisément accessible.
Pour éviter les dommages matériels aux appareils XIRIUM PRO causés par des conditions climatiques
ou de fonctionnement inadéquates :
•Ne jamais l'immerger dans l'eau.
•Protéger l'appareil des forts rayons du soleil.
•Ne jamais installer l'appareil près de sources de chaleur comme un radiateur, un appareil de
chauffage, un four ou un poêle.
•Afin d'éviter une surchauffe, ne jamais couvrir l'appareil.
•Il faut protéger l'appareil des impacts et surtout l'empêcher de tomber d'une perche, d'une
estrade, d'une table ou d'un meuble.
•Toujours installer et fixer l'appareil comme illustré dans la section «5.8.4 Fastening and securing
XIRIUM PRO devices» on page 42.
10
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Safety
Réparation
DANGER
Risque de blessures, d'électrocution et de dommages matériels en cas de réparations
inappropriées!
Les appareils XIRIUM PRO ne contiennent aucune pièce pouvant être réparée par l'utilisateur. L'ou-
verture ou la réparation des appareils par l'utilisateur peuvent entraîner des dommages graves aux
appareils, des blessures ou une électrocution de l'opérateur.
cNe pas ouvrir le boîtier des appareils XIRIUM PRO en aucun cas.
cL'utilisateur ne doit pas changer de pièces lui-même.
cFaire réparer tout appareil XIRIUM PRO uniquement par un détaillant spécialisé autorisé.
Branchement électrique
DANGER
Risque d'électrocution lors du branchement ou du débranchement au réseau électrique!
cBrancher seulement l'appareil à des prises de courant installées par des électriciens qualifiés.
cNe pas manipuler les appareils avec les mains humides ou mouillées en aucun cas.
cS'assurer que la fréquence et la tension du réseau correspondent aux spécifications.
cUtiliser seulement le cordon d'alimentation électrique fourni pour brancher l'appareil à la prise
de courant.
cPendant les tempêtes où lorsqu'il y a des risques de fluctuation de tension, fermer l'appareil et
le débrancher du réseau électrique.
cS'assurer que le cordon d'alimentation n'est pas plié, suspendu sur une arête tranchante ou en
contact avec des surfaces chaudes pendant le fonctionnement.
cNe pas utiliser les appareils s'il y a des interférences ou si l'appareil, l'écran ou les accessoires
sont endommagés.
Informations relatives au fonctionnement
cS'assurer que les conditions ambiantes prévues sont respectées pendant le fonctionnement du
XIRIUM PRO.
cNe pas utiliser les appareils XIRIUM PRO s'ils ne fonctionnent pas adéquatement, s'ils sont
tombés ou s'ils sont endommagés ou si des pièces de l'appareil ont été immergées dans l'eau.
cSi des perturbations se produisent pendant le fonctionnement :
Éteindre immédiatement l'appareil XIRIUM PRO et le débrancher du réseau électrique.
cNe faites pas fonctionner l'appareil XIRIUM PRO dans des environnements où des matériaux, des
gaz ou des vapeurs inflammables ou explosifs peuvent être présents ou peuvent se produire.
2.5 Proper use
The XIRIUM PRO devices are intended for signal transmission between an audio source and an audio
sink in accordance with the technical specications.
2.6 Foreseeable improper use
The XIRIUM PRO devices are not suitable for use in potentially explosive atmospheres.
11
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Components and accessories
3 Components and accessories
3.1 XIRIUM PRO components
The components and accessories are ordered individually.
2
13 14
15 16
17 18
1
78
3 4
10
11 12
9
5 6
12
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Components and accessories
* Quick Start Guide included in scope of delivery.
Pos. Description Article no.
1 TX base station*
(TX base station, XIRIUM PRO USB data cable, ManfrottoTM universal
mounting clamp, 5 GHz antenna, 2.4 GHz antenna)
NXP2TX-C
2 RX base station*
(RX base station, XIRIUM PRO USB data cable, ManfrottoTM universal
mounting clamp, 2.4 GHz antenna)
NXP2RX-C
3TX modules
•TX module analog*
•TX module AES*
•TX module DANTE*
NXP-TM-ANA
NXP-TM-AES
NXP-TM-DANTE
4RX modules
•RX module analog*
•RX module AES*
•RX module DANTE*
•Repeater module*
NXP-RM-ANA
NXP-RM-AES
NXP-RM-DANTE
NXP-RM-RP
5 5 GHz antenna 9 dBi 360°H 12.5°V NXPA-9-360-12.5
65 GHz antenna 6 dBi 360°H 25°V NXPA-6-360-25
75 GHz directional antenna 14 dBi 40°H 35°V, including adapter to
mount the antenna directly on a receiver if no repeater module is
inserted!
NXPA-14-40-35
8 2.4 GHz omnidirectional antenna for connecting app NXPA-WIFI
9 5 GHz directional antenna (for remte setup) 18 dBi 18°H 18°V, for
receiver if no repeater module is inserted! (cable not included!)
NXPA-18-18-18
10 5 GHz omnidirectional antenna 2 dBi 360°H 360°V, for repeater
setups with different antenna heights (see page 26)
NXPA-2-360
11 Antenna cable S04162B, N type connectors, 5 m, 4 dB attenuation NKXPA-5
12 N Adapter female female, for remote TX antenna (cable not icluded!) NXPA-N-FF
13 ManfrottoTM universal mounting clamp NXUC-M-15
14 Mounting arm for XIRIUM PRO antennas (NXPA-14-14-35, NXPA-18-
18-18, NX-6-360-25), compatible with ManfrottoTM clamp
NXPMA
15 Power cable XIRIUM PRO, 3 m NKXPF-5-15-3
16 XIRIUM PRO data cable NKXP-DATA
17 Flight case with foam cut-outs to hold 2x base stations (not included) CAS-NXP
18 Hard case (trolley) with foam cut-outs to hold 3 devices (not included) CAS-NXP-T
* Power cables have to be ordered seperately!
13
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Description of product
11
66
78
22
Pos. Designation
15 GHz antenna connector with 5 GHz
antenna
The antenna transmits the signals between the
XIRIUM PRO devices.
22.4 GHz antenna connector (reverse SMA)
with 2.4 GHz antenna
Transmits control data via WIFI
3Housing
Extruded aluminum housing
4Lug
Safety lug for additional fall arresting
5Bolt
Adapter for mounting with a ManfrottoTM clamp
6On/off switch
Powering the device ON/OFF, LED indication
LED display:
•LED off: Device off or powering up.
•LED solid green: Device powerd-on and battery
level is between 20 % and 100 %.
•LED slow-ash green: Device powerd-on and
battery is charging.
•LED solid red: Firmware update active.
•LED slow-ash red: Device identication
activated from app by pressing the Identify
Device button.
•LED quick-ash red: Battery below 20 %.
4 Description of product
4.1 XIRIUM PRO base station
ON/OFF LINK push 1s
XROC push 4s
ON/OFF LINK push 1s
DELAY push 4s
ON/OFF LINK push 1s
XROC push 4s
ON/OFF LINK push 1s
DELAY push 4s
TX, top view
Bottom view
RX, top view
Pos. Designation
7TX link button
Linking devices, switching XROC mode ON/OFF,
resetting transmission power
•Push and release: Start/stop LINK process
•Hold 4 sec: Toggle XROC mode ON/OFF
•Hold 8 sec: Reset transmission power
LED display:
•LED off: TX not transmitting audio signal.
•LED solid blue: TX transmitting audio signal.
•LED quick-ash blue: Device is activated for
linking process.
•LED slow-ash blue: XROC mode set to ON.
8RX link button
Linking devices; switching delay ON/OFF
•Push and release: Start/stop LINK process
•Hold 4 sec: Toggle delay ON/OFF
•Hold 8 sec: Reset repeater transmission power
LED display:
•LED off: RX not receiving audio signal.
•LED solid blue: RX receiving audio signal.
•LED quick-ash blue: Device is activated for
linking process.
•LED slow-ash blue: Delay set to ON.
9Type plate
With serial number, SSID and WLAN password
10 D-Sub connector
Interface between base station and module.
11 USB port
USB connection for rmware update
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
1
2
3
4
5
10911
14
User Manual – XIRIUM PRO® CA | BDA 471 2017/03
Description of product
4.2 Modules
TX AES module
RX DANTE moduleRX analog module
Repeater module
RX AES module
TX DANTE moduleTX analog module
Top view Bottom view
4.2.2 RX modules
4.2.1 TX modules
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
100-240V~ 0.5A 50-60Hz
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
RX
LIECHTENSTEIN
100-240V~ 0.5A 50-60Hz
AES
RX
LIECHTENSTEIN
OUT
1 3 2
EBU
/
RX
LIECHTENSTEIN
LINE
OUT 1 (XROC) OUT 2
1 3 2 1 3 2
DANTE
C6
A
RX
LIECHTENSTEIN
OUT
C6
A
TX
LIECHTENSTEIN
IN
AES
1 2
3
EBU
/
PUSH
DANTE
C6
A
TX
LIECHTENSTEIN
IN
C6
A
REPEATER
RX
LIECHTENSTEIN
TX
LIECHTENSTEIN
IN 2
IN 1 (XROC)
LINE
1 2
3
PUSH
1 2
3
PUSH
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz
1
2
3
3 1 564
Pos. Description
1D-Sub connector
interface between base station and module
2Module with integrated battery
3Locking bolt
4LED charging indicator
•Flashes green: Battery charging.
•Lit green: Battery fully charged.
Pos. Description
5Audio IN (TX), audio OUT (RX)
(different connections depending on module)
6powerCON TRUE1 chassis
for XIRIUM PRO power cable

Navigation menu