New Centurion Solutions NCS02010910 HANDHELD SECURITY DEVICE User Manual Project 623

New Centurion Solutions, Inc. HANDHELD SECURITY DEVICE Project 623

Contents

Users Manual HUB

THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. Elliott Tech, LLC HUB Installation Manual HUB New Centurion Solutions Project Number: 776 Reference: 776-91-05-REV-HUB_INSTALLATION_MANUAL.docx Original Document: March 1, 2011 Revision A: March 16, 2011 Prepared for: Prepared by: New Centurion Solutions, Inc. Greg Williams 3011 Spring Garden St. Suite E Greensboro, NC 27403 (336) 617-5410 GWilliams@newcenturionsolutions.com Elliott Tech, LLC 346 Raleigh Street Holly Springs, NC 27540 (919) 342-6899 (888) 631-1795 Fax s.elliott@elliotttech.com
HUB Installation Manual 776-91-05-REV-A_HUB_INSTALLATION_MANUAL.docx THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. ii Revision Page Rev Description Section A FCC Notification 3
HUB Installation Manual 776-91-05-REV-A_HUB_INSTALLATION_MANUAL.docx THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. iii Contents 1. Equipment List ......................................................................................................... 4 2. Installation Instructions .......................................................................................... 5 3. FCC Notification ...................................................................................................... 6
HUB Installation Manual 776-91-05-REV-A_HUB_INSTALLATION_MANUAL.docx THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. 4 1. EQUIPMENT LIST A. USB Cable, Type A to Type B (1) B. Hub Assembly (1) C. Flexible ½ wave center-fed dipole antenna with articulated knuckle (1) D. HUB Power Supply (1) E. Personal Computer (PC) (1) F. U.L. approved power cord, 6 ft. length (1)
HUB Installation Manual 776-91-05-REV-A_HUB_INSTALLATION_MANUAL.docx THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. 5 2. INSTALLATION INSTRUCTIONS To begin, check the parts available against the equipment list, identifying any missing parts. If all parts are accounted for, proceed to the instructions below to begin installing the HUB. Step 1: Identify the Flexible ½ wave center-fed dipole antenna with articulated knuckle (C). Screw the antenna into the gold coaxial antenna connector on the front panel of the HUB assembly (B). Ensure that the antenna is screwed onto the connector snugly, but take care not to over-tighten the antenna as it will damage the connector or the HUB assembly front panel. Step 2: Identify the USB Cable, Type A to Type B (A). The type-A end of the cable is smaller and flatter than the type-B end of the cable and will mate with a standard USB port on a PC. Plug this end into one of the USB ports on the Personal Computer (PC) (E). Plug the other end (Type-B) into the mating USB connector on the front panel of the HUB assembly (B). Type-A Type-B
HUB Installation Manual 776-91-05-REV-A_HUB_INSTALLATION_MANUAL.docx THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC. 6 Step 3: Identify the HUB Power Supply (D). Plug the barrel jack plug into the mating barrel jack on the front panel of the HUB assembly (B). Plug the U.L. approved power cord, 6 ft. length (F) into the HUB Power Supply (D). Only one end will mate with it properly. Plug the other end of the power cord into a standard 120 Volt wall outlet. The green light on the front panel of the HUB should illuminate. 1 – Green status indicator light / yellow status indicator light 2 – Flexible ½ wave center-fed dipole antenna with articulated knuckle 3 – USB cable type-B end, plugged into the HUB assembly 4 – Green power indicator light – this should illuminate whenever the HUB is correctly connected to a power source 5 – Barrel jack plug of HUB Power Supply (D), plugged into the barrel jack of the HUB assembly 3. FCC NOTIFICATION NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Navigation menu