Nikko Co TP6830 Radio Controlled Toy(Transmitter) User Manual KMNA103620 indd

Download:
Mirror Download [FCC.gov]
Document ID	668159
Application ID	OeinNIiAkyglaJs47SkheQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	80.54kB (1006746 bits)
Date Submitted	2006-06-13 00:00:00
Date Available	2006-06-09 00:00:00
Creation Date	2006-03-06 12:10:07
Producing Software	Adobe PDF Library 6.0
Document Lastmod	2006-03-07 17:06:12
Document Title	KMNA103620.indd
Document Creator	Adobe InDesign CS (3.0.1)

1/10 SCALE
Owner's Manual
CAUTION: ELECTRIC TOY
PRINTED IN CHINA
© NIKKO
Repair and Parts Department
Monday to Friday 8:30AM-5:30PM
Central Time
Repair :(800)736-4556
Parts :(800)776-4556
Fax :(972)578-7059
e-mail :help@nikkoamerica.com
NOT RECOMMENDED FOR CHILDREN
UNDER 8 YEARS OF AGE. AS WITH
ALL ELECTRIC PRODUCTS, PRECAUTIONS SHOULD BE OBSERVED
DURING HANDLING AND USE TO
PREVENT ELECTRIC SHOCK.
INPUT: 120VAC, 60HZ,
OUTPUT: 12VDC, 200mA
ATTENTION PARENTS
* Recharge the Battery
Before
You Start to Operate
It is recommended that this toy and all
accessories be periodically examined
for potential hazards and that any potential hazardous parts be repaired or
replaced.
* Read this Manual carefully to the end before beginning to play.
* WARNING! Use under the direct supervision of an adult.
* Keep the Display Box and Manual for future reference.
* Use Ni-Cd battery pack(9.6V) and charger for this model.
* Actual product may vary from illustration of this manual.
FEATURES
•
3 channel Full Function
BATTERY REQUIREMENTS
--- Forward,Reverse, Left/Right turn and Stop
(Not included)
3 Band Sector Switch
• 2 Speed in Forward
2 Speed by Transmitter Operation
• Front & Rear Suspension
• Rear Wheel Different Gear
• Head Light
• Spinner Wheel
•
Vehicle: 1 x Ni-Cd or
NI-MH rechargeable
battery pack(9.6V)
Transmitter:1 x 9V(006P)battery
RECHARGING
* The newly purchased Ni-Cd pack is not
charged. Recharge before operate.
Charger
1. Join the connector of the charger to the
connector of the Ni-Cd battery pack (9.6 V).
2. Plug the charger into an electrical outlet.
3. Recharge for about 4-5 hours.
4. When the recharging is over, plug out the
charger from the electrical outlet and
detach the connectors.
Household
outlet
Ni-Cd battery pack
Charger
OR
Ni-Cd battery pack
Household
outlet
CAUTION:
* Do not charge Battery Pack immediately after use. Wait until it is cooled before charging.
* Avoid short circuits. Short circuits will cause overheating, burning of the cords and other
damages to the Battery Pack and Charger.
* The Ni-Cd Battery Charger should be used for charging one Battery Pack. Do not use the
charger for charging other types of batteries and battery packs.
* Do not use the Charger as a direct current outlet for other electrical appliances or machines.
* Make sure that the Battery Pack and Charger are kept out of the hands of infants and small
children while charging.
* Do not charge near fires, where the temperature is extremely high, or where it is wet or damp.
* The charger will become slightly heated while charging. Allow sufficient free space around
the Charger.
* If the power of the battery pack is weak in spite of proper charging. The batteries may be worn
out from repeated use. Replace it with a new Ni-Cd battery pack.
* Dispose of use Ni-Cd battery packs correctly.
* Disconnect the supply before making or breaking connections to the battery.
* WARNING AGAINST RECHARGING NON-RECHARGEABLE BATTERIES.
* Please use this battery charger only for the charger of the rechargeable battery pack.
* The Ni-Cd battery pack should be recharged under the supervision of an adult.
PREPARATION FOR STARTING OPERATION
1. HOW TO ATTACH ANTENNA TUBE
Antenna wire
Pass the antenna wire through the antenna tube, then insert the tube into the
antenna tube holder.
Antenna Tube
Antenna tube
holder
If the antenna tube cannot be successfully
inserted into the antenna tube holder, try
holding the root of the antenna wire with
fingers of one hand and extending the
wire with fingers of the other hand.
* Note: Be careful not to pull antenna wire
too strong.
Spinner Wheels
2. HOW TO INSTALL TRANSMITTER ANTENNA
Place the transmitter antenna into the antenna
holder to screw it in
clockwise.
Don’t install the antenna extended.
It’s dangerous.
If the antenna is not screwed in securely,
the vehicle may move erratically. Screw the
antenna securely.
3. HOW TO INSTALL THE BATTERY
One 9 volt (006P) battery
Transmitter
Install battery making sure that (+) and (-) poles
are positioned properly.
To remove the battery lid, press the point
marked “OPEN” and pull the lid downward.
* Dispose the used battery separately from other trash.
Vehicle
When installing a Ni-Cd battery pack,
make sure that the power switch of the vehicle is OFF.
Battery stopper
Battery compartment lid
Ni-Cd Battery pack (9.6 V)
1 Use a coin to turn the battery stopper to
the "OPEN" position.
3 Join the connectors of the vehicle and
2 Let the battery compartment lid slide
the Ni-Cd battery pack.
forward a little with a pressure on to the
latch.
Battery compartment
5 Press down the battery compartment lid
4 Fit the Ni-Cd battery pack into the
when Use a coin to turn the battery
stopper.
battery compartment of your vehicle
and push in all the way.
When you connect the connectors make certain the vehicle switch is in
the "OFF" position.
Set connectors properly. ( The connectors are designed to be
connected in only one way so that the positive (+) and the negative (-)
terminals are connected accurately. )
Disconnect the connectors immediately after a run.
When you disconnect the connectors, don't pull by the cords.
Avoid short circuits because it is very dangerous.
Remove all the batteries both from the vehicle and the transmitter after
a run.
Vehicle's Connector
Battery's Connector
HOW TO PLAY
Band selector switch on vehicle chassis.
Band selector switch on transmitter.
1 Ensure that band selector switch on transmitter and vehicle are set to the same letter
- A, B or C.
Race 6 cars at once!
3 channels for each frequency, 27MHz, 49MHz, allows up to 6 cars to race at once.
27MHz
49MHz
3 Turn on the transmitter by operating the
2 Extend the transmitter antenna.
control stick.
* You can control the vehicle at a longer distance
by holding the transmitter higher with the an
tenna straight up.
power switch
5 Start operation.
4 Turn ON the power switch of the vehicle.
FORWARD RUNNING
Low
Low
High
High
You can enjoy the excitement of 2 stages of speed from
LOW to HIGH speed forward running by operating the
speed control stick.
HIGH SPEED
Forward/Reverse
control stick
LOW SPEED
FORWARD
Steering control stick
LEFT/STRAIGHT/RIGHT
STOP
(NEUTRAL)
REVERSE
Power switch
6 Turn OFF the vehicle after playing.
7 To prevent damage from battery leakage,
remove all the batteries from transmitter
and vehicle after playing.
TO ADJUST STEERING ALIGNMENT
Adjust the steering alignment when the vehicle does not run straight forward.
Tu r n t h e s t e e r i n g
alignment lever
towards “R” if the
vehicle runs towards
left.
Tu r n t h e s t e e r i n g
alignment lever
towards “L” if the
vehicle runs towards
right.
Drift driving technique
Drift is a driving technique to make a
car slips and swings in a corner.
Recommended place to play
Slippery road
(P-tiles, wooden floor, concrete)
Note:
Drift might not happen depending on road
conditions.
How to play
Replace the rear wheels or four wheels with drift tires.
Drift tires are installed on the front
and rear wheels
Drift tires are installed on the rear
wheels only
Image of drift
At the
fastest speed
How to install drift tires

Front tire
Pay attention to the forward
direction when you install the
pattern tires.
Wheel cap
Wheel
wrench
FORWARD
Rear tire
Wheel
Drift tire
Holding the tire not to move, insert the
wheel wrench and turn, and remove the
wheel cap. Do the same when reinstalling
the wheel cap.
Push the wheel wrench counterclockwise
a little harder and pull the wheeel cap to
remove.
Spinner wheel
Slots for the
wheel wrench
Turn the wheel wrench counterclockwise
until it "clicks".
* Push a little harder counterclockwise
as illustrated, because it would be
difficult to pull it out straight.
Pull out the original tire and install the drift
tire. After that, put back the wheel cap.
Push the wheel cap into the inner part
until the nail of the wheel cap and the
cut of the wheel are brought together.
Turn the wheel wrench clockwise until it
"clicks." This completes the work.
OPERATING SAFETY RULES
Select a SAFE place to operate your vehicle. Do not drive in the street. Avoid driving on SAND or through
puddles of WATER. These hazards can impair performance. Check the surface ahead of you and watch for
obstacles.
The radio receiver in your vehicle and transmitter are sensitive instruments. Do not leave Vehicle or Transmitter near sources of HEAT or under DIRECT SUNLIGHT for long periods of time.
Avoid leaving Vehicle or Transmitter OUTSIDE OVERNIGHT. NIGHT DAMPNESS IS HARMFUL TO INTERIOR MECHANISM.
Cleaning and maintenance:
This toy vehicle needs periodic maintenance and cleaning.
Warning to the parents:
The charger for the Ni-Cd battery pack needs periodic inspection to see that the lead wires, plugs,
outer case, and other parts are not damaged in any way. If any of the parts are damaged, do not use
the charger until it is completely repaired.
Caution:
Keep out of reach of small children under 36 months old as there is danger of getting hurt.
* CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
MANUFACTURER FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.
RADIO INTERFERENCE: Sometimes erratic behavior or loss of control of vehicle is the result of interference
caused by high tension wires, high voltage transformers, certain types of building, concreate walls or narrow
places where RADIO SIGNALS sent from your transmitter MAY BE SCATTERED thus making it DIFFICULT
for your vehicle to receive a GOOD RADIO SIGNAL. If you encounter this type of behavior or loss of control,
CHANGE TO A DIFFERENT LOCATION.
You will encounter INTERFERENCE if ANOTHER radio controlled vehicle or CB radio is operating in the vicinity on your SAME FREQUENCY.
DO NOT operate your vehicle on thick-piled carpets. It can be dangerous since the carpet
fiber may twine round a shaft and cause a motor overheated.
THE RBRCTMSeal on the nickel cadmium battery pack
indicates that NikkoAmerica is voluntarily participating in an industry program
to collect and recycle these batteries at the end of their useful life. The RBRC
program provides a convenient alternative to disposing nickel-cadmium batteries
into the trash or municipal waste stream, which is illegal in some areas.
Nikko America's payments to RBRC makes it easy for you to drop off the spent
battery pack at local retailers who sell replacement nickel-cadmium batteries.
You may also contact your local recycling center for information on where to return
the spent battery pack.
RBRC is a trademark of the Rechargeable Battery Recycling Corporation.
THE FCC WANTS YOU KNOW
This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Your R/C car might cause TV or radio interference even when it is operating properly.
To determine whether your R/C car is causing the interference, turn off your R/C car.
If the interference goes away, your R/C car is causing the interference.
Try to eliminate the interference by:
* Moving your R/C car away from the receiver.
* Contacting your local store for help.
If you cannot eliminate the interference, the FCC requires that you stop using your R/C car.
KMNA103620 KYP-06-00

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 8
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:a02f6d04-adb9-11da-96ac-0011247be4e0
Create Date                     : 2006:03:06 12:10:07Z
Modify Date                     : 2006:03:07 17:06:12+08:00
Metadata Date                   : 2006:03:07 17:06:12+08:00
Creator Tool                    : Adobe InDesign CS (3.0.1)
Version ID                      : 1
Rendition Class                 : proof:pdf
Derived From Instance ID        : 241e9645-ae9b-11da-a8ec-f00696b2c566
Derived From Document ID        : adobe:docid:indd:0625e151-01ac-11da-9b27-8521093e38d1
Derived From Version ID         : 1
Document ID                     : adobe:docid:indd:241e9646-ae9b-11da-a8ec-f00696b2c566
Manifest Link Form              : ReferenceStream
Manifest Reference Instance ID  : uuid:7e5b5e56-7932-11da-9e17-d28102f8b89f
Manifest Reference Document ID  : adobe:docid:photoshop:1376b775-5f54-11da-886c-82fe1e8230fe
Format                          : application/pdf
Title                           : KMNA103620.indd
Trapped                         : False
Creator                         : Adobe InDesign CS (3.0.1)
Producer                        : Adobe PDF Library 6.0

EXIF Metadata provided by EXIF.tools