Nikon 4151E Digital Camera User Manual Part 2
Nikon Corporation Digital Camera Users Manual Part 2
Nikon >
Contents
- 1. Users Manual Part 1
- 2. Users Manual Part 2
Users Manual Part 2
The Shooting Menu (for A (Auto) Mode) Image Mode (Image Size and Quality) Enter shooting mode* M d button M Image mode M k button * This setting can also be changed in shooting modes other than auto. The changed setting is also applied to other shooting modes. Select the combination of image size and compression ratio to be used when saving images. The higher the image mode setting, the larger the size at which it can be printed, and the lower the compression ratio, the higher the quality of the images, but the number of images that can be saved is reduced. Option* Compression ratio Aspect ratio (horizontal to vertical) Using Menus w 5152×3864P Approx. 1:4 4:3 x 5152×3864 (default setting) Approx. 1:8 4:3 i 3648×2736 Approx. 1:8 4:3 r 2272×1704 Approx. 1:8 4:3 q 1600×1200 Approx. 1:8 4:3 O 640×480 Approx. 1:8 4:3 z 5120×2880 Approx. 1:8 16:9 s 3864×3864 Approx. 1:8 1:1 * The numerical values indicate the number of pixels that are captured. Example: x 5152×3864 = approx. 20 megapixels, 5152 × 3864 pixels 66 B Notes About Printing Images at 1:1 Aspect Ratio Change the printer setting to “Border” when printing images at a 1:1 aspect ratio. Some printers may not be able to print images at a 1:1 aspect ratio. Notes About Image Mode This function may not be available to use in combination with other functions (A48). Number of Images That Can Be Saved • The approximate number of images that can be saved can be checked in the monitor when shooting (A10). • Note that due to JPEG compression, the number of images that can be saved may vary greatly depending on the image content, even when using memory cards with the same capacity and the same image mode setting. In addition, the number of images that can be saved may vary depending on the make of the memory card. • If the number of exposures remaining is 10,000 or more, the number of exposures remaining display shows “9999”. Using Menus 67 White Balance (Adjusting Hue) Enter shooting mode M A (shooting mode) button M A (auto) mode M k button M d button M White balance M k button Adjust white balance to suit the light source or weather conditions in order to make the colors in images match what you see with your eyes. Option Using Menus 68 Description a Auto (default setting) White balance is automatically adjusted. b Preset manual Use when the desired result is not achieved with Auto, Incandescent, etc. (A69). c Daylight Use under direct sunlight. d Incandescent Use under incandescent lighting. e Fluorescent Use under fluorescent lighting. f Cloudy Use under overcast skies. g Flash Use with the flash. Notes About White Balance • Set the flash to W (off) when white balance is set to any setting other than Auto and Flash (A35). • This function may not be available to use in combination with other functions (A48). Using Preset Manual Use the procedure below to measure the white balance value under the lighting used during shooting. Place a white or gray reference object under the lighting that will be used during shooting. Use the multi selector HI to select Preset manual in the White balance menu, and press the k button. • The camera zooms in to the position for measuring white balance. Select Measure. White balance Auto Preset manual Daylight Incandescent Fluorescent Cloudy Preset manual • To apply the last measured value, select Cancel and press the k button. Cancel Measure Frame the white or gray reference object in the measuring window, and press the k button to measure the value. • The shutter is released and measurement is complete (no image is saved). Preset manual Using Menus Cancel Measure Measuring window Notes About Preset Manual A value for flash lighting cannot be measured with Preset manual. When shooting using the flash, set White balance to Auto or Flash. 69 Continuous Shooting Enter shooting mode M A (shooting mode) button M A (auto) mode M k button M d button M Continuous M k button Option Description U Single (default setting) One image is captured each time the shutter-release button is pressed. V Continuous While the shutter-release button is held all the way down, images are captured continuously. • The frame rate for continuous shooting is about #.# fps and the maximum number of continuous shots is about # (when image mode is set to x 5152×3864). Notes About Continuous Shooting • Focus, exposure, and white balance are fixed at the values determined with the first image in each series. • It may take some time to save the images after shooting. • This function may not be available to use in combination with other functions (A48). Using Menus 70 ISO Sensitivity Enter shooting mode M A (shooting mode) button M A (auto) mode M k button M d button M ISO sensitivity M k button A higher ISO sensitivity allows darker subjects to be captured. Additionally, even with subjects of similar brightness, pictures can be taken at faster shutter speeds, and blurring caused by camera shake and subject movement can be reduced. • When a higher ISO sensitivity is set, images may contain noise. Option Description a Auto (default setting) Sensitivity is automatically selected from the range of ISO 80 to 1600. I Fixed range auto Select the range in which the camera automatically adjusts ISO sensitivity, from ISO 80-400 or ISO 80800. 80, 100, 200, 400, 800, 1600, 3200 Sensitivity is locked at the specified value. Notes About ISO Sensitivity Notes About ISO 3200 When ISO sensitivity is set to 3200, the available Image mode settings are limited to r 2272×1704, q 1600×1200, and O 640×480. X is displayed next to the ISO sensitivity indicator in the monitor. Using Menus This function may not be available to use in combination with other functions (A48). 3200 ISO Sensitivity Display on the Shooting Screen • When Auto is selected, E is displayed when the ISO sensitivity increases. • When Fixed range auto is selected, the maximum value for ISO sensitivity is displayed. 71 AF Area Mode Enter shooting mode M A (shooting mode) button M A (auto) mode M k button M d button M AF area mode M k button Set how the camera selects the focus area for autofocus. Option Description When the camera detects a human face, it focuses on that face. See “Using Face Detection” (A43) for more information. 8m 0s 1400 Focus area a Face priority Using Menus x Manual 72 When framing a composition with no human subjects or detected faces, the camera automatically selects one or more of the nine focus areas containing the subject closest to the camera when the shutter-release button is pressed halfway. Use the multi selector HIJK to move the focus area to where you want to focus. • To use the multi selector to configure the flash mode or other settings, press the k button. To return to moving the focus area, press the k button again. 1/250 F3.7 Focus areas Scope of movable focus area Focus area Option Description The camera focuses on the subject in the center of the frame. y Center 8m 0s 1400 Focus area s Subject tracking Start 1400 When the camera detects the main subject, it focuses on that subject. See “Using Target Finding AF” (A45) for more information. 1/250 F3.7 Using Menus M Target finding AF (default setting) Use this function to take pictures of moving subjects. Register the subject on which the camera focuses. The focus area automatically moves to track the subject. See “Using Subject Tracking” (A74) for more information. Focus areas Notes About AF Area Mode • When digital zoom is in effect, the camera focuses in the center of the frame regardless of the AF area mode setting. • This function may not be available to use in combination with other functions (A48). 73 Using Subject Tracking Enter shooting mode M A (shooting mode) button M A (auto) mode M k button M d button M AF area mode M k button M s Subject tracking M k button M d button Register a subject. • Align the subject that you want to track with the border in the center of the monitor and press the k button. • When the subject is registered, a yellow border (focus area) is displayed around it and the camera begins tracking the subject. • If the subject cannot be registered, the Start border is displayed in red. Change the composition and try registering the subject again. • To cancel subject registration, press the k button. • If the camera can no longer track the registered subject, the focus area disappears. Register the subject again. Using Menus Press the shutter-release button fully to take the picture. • If the shutter-release button is pressed while the focus area is not displayed, the camera focuses on the subject in the center of the frame. 1/250 F3.7 Notes About Subject Tracking • If you perform operations such as zooming while the camera is tracking the subject, the registration is canceled. • Subject tracking may not be possible in certain shooting conditions. 74 Autofocus Mode Enter shooting mode M A (shooting mode) button M A (auto) mode M k button M d button M Autofocus mode M k button Set how the camera focuses when shooting still images. Option Description A Single AF (default setting) The camera focuses only when the shutter-release button is pressed halfway. B Full-time AF The camera continues focusing even when the shutter-release button is not pressed halfway. The sound of lens drive movement is heard while the camera focuses. Autofocus Mode for Movie Recording Autofocus mode for movie recording can be set with Autofocus mode (A84) in the movie menu. Using Menus 75 The Smart Portrait Menu • See “Image Mode (Image Size and Quality)” (A66) for information about Image mode. Self-Collage Enter shooting mode M A (shooting mode) button M F Smart portrait mode M k button M d button M Self-Collage M k button Option Using Menus 76 Description Number of shots Set the number of shots that the camera automatically captures (number of captured images for an aggregated image). • 4 (default setting) or 9 can be selected. Interval Set the interval time between each shot. • Short, Medium (default setting), or Long can be selected. Shutter sound Set whether to activate the shutter sound when shooting with the self-collage function. • Standard, SLR, Magic (default setting), or Off can be selected. • The same setting that is specified for Shutter sound in Sound settings in the setup menu is not applied to this setting. Blink Proof Enter shooting mode M A (shooting mode) button M F Smart portrait mode M k button M d button M Blink proof M k button Option Description y On The camera automatically releases the shutter twice with every shot and saves one image in which the A blink was detected in the picture just taken. subject’s eyes are open. • If the camera saved an image in which the subject’s eyes may have been closed, the dialog shown on the right is displayed for a few seconds. • The flash cannot be used. Off (default setting) Turns the blink proof off. Notes About Blink Proof Using Menus This function may not be available to use in combination with other functions (A48). 77 The Playback Menu • See “Editing Images (Still Images)” (A53) for information about image editing functions. Mark for Wi-Fi Upload Press the c button (playback mode) M d button MMark for Wi-Fi upload M k button Select images in the camera that you want to transfer to a smart device in advance before transferring them. On the image selection screen (A82), select or deselect images for the Mark for Wi-Fi upload function. Note that when you select Reset all (A99) in the setup menu or Restore default settings (A86) in the Wi-Fi options menu, the Mark for Wi-Fi upload settings that you made are canceled. Using Menus 78 Slide Show Press the c button (playback mode) M d button M Slide show M k button Play back images one by one in an automated “slide show.” When movie files are played back in the slide show, only the first frame of each movie is displayed. Use the multi selector HI to select Start and press the k button. Slide show Start Frame intvl • The slide show begins. Loop • To change the interval between images, select Frame intvl, press the k button, Pause and specify the desired interval time before selecting Start. • To repeat the slide show automatically, select Loop and press the k button before selecting Start. • The maximum playback time is up to about 30 minutes even if Loop is enabled. End or restart the slide show. • The screen shown on the right is displayed after the slide show ends or is paused. To exit the show, select G and then press the k button. To resume the slide show, select F and then press the k button. Using Menus Operations During Playback • Use the multi selector JK to display the previous/next image. Press and hold to rewind/fast forward. • Press the k button to pause or end the slide show. 79 Protect Press the c button (playback mode) M d button M Protect M k button The camera protects selected images from accidental deletion. Select images to protect or cancel protection from the image selection screen (A82). Note that formatting the memory card or the camera’s internal memory permanently deletes all data including protected files (A96). Rotate Image Press the c button (playback mode) M d button M Rotate image M k button Specify the orientation in which saved images are displayed during playback. Still images can be rotated 90 degrees clockwise or 90 degrees counterclockwise. Using Menus Select an image from the image selection screen (A82). When the Rotate image screen is displayed, press the multi selector JK to rotate the image 90 degrees. Rotate image Back Rotate image Rotate image Rotate Rotate 90 degrees counterclockwise Back Rotate Back Press the k button to finalize display orientation, and save orientation information with the image. 80 Rotate Rotate 90 degrees clockwise Copy (Copy Between the Memory Card and Internal Memory) Press the c button (playback mode) M d button M Copy M k button Images can be copied between a memory card and the internal memory. • When a memory card that contains no images is inserted and the camera is switched to playback mode, Memory contains no images. is displayed. In that case, press the d button to select Copy. Use the multi selector HI to select a destination option to which images are copied and press the k button. Select a copy option and press the k button. Camera to card Card to camera Camera to card Selected images All images Using Menus • When you choose Selected images, use the image selection screen to specify images (A82). Copy Notes About Copying Images • Only files in formats that this camera can record can be copied. • Operation is not guaranteed with images captured with another make of camera or that have been modified on a computer. 81 The Image Selection Screen When an image selection screen such as the one shown on the right is displayed while operating the camera, follow the procedures described below to select the images. Protect Back Use the multi selector JK to select an image. • Move the zoom control (A1) toward g (i) to switch to full-frame playback or f (h) to switch to thumbnail playback. • Only one image can be selected for Rotate image. Proceed to step 3. Use HI to select or deselect (or to specify the number of copies). Protect Back Protect • When an image is selected, an icon is displayed below the image. Repeat steps 1 and 2 to select additional images. Using Menus 82 Back Press the k button to apply image selection. • When a confirmation dialog is displayed, follow the on-screen instructions to operate. The Movie Menu Movie Options Enter shooting mode M d button M D menu icon M Movie options M k button Select the desired movie option to record. The movie options that can be selected vary depending on the Video mode setting (A97). • Memory cards with an SD Speed Class rating of 6 or faster are recommended for recording movies (A136). Option (Image size/Frame rate) Image size Aspect ratio (horizontal to vertical) f 720/30p V 720/25p (default setting*) 1280 × 720 16:9 g 480/30p W 480/25p 640 × 480 4:3 u 240/30p q 240/25p 320 × 240 4:3 Using Menus * When recording in the internal memory, the default setting is g 480/30p or W 480/25p, and f 720/30p or V 720/25p cannot be selected. 83 Autofocus Mode Enter shooting mode M d button M D menu icon M Autofocus mode M k button Set how the camera focuses in movie mode. Option Using Menus 84 Description A Single AF (default setting) Focus is locked when movie recording starts. Select this option when the distance between the camera and subject will remain fairly consistent during movie recording. B Full-time AF The camera focuses continuously during movie recording. Select this option when the distance between the camera and subject will change significantly during recording. The sound of the camera focusing may be heard in the recorded movie. Use of Single AF is recommended to prevent the sound of the camera focusing from interfering with recording. Movie VR Enter shooting mode M d button M D menu icon M Movie VR M k button Select the vibration reduction setting used when recording movies. Select Off when using a tripod to stabilize the camera during shooting. Option Description V On (hybrid) (default setting) Performs optical compensation for camera shake using lens shift VR and simultaneously performs electronic VR using image processing. The angle of view (i.e., the area visible in the frame) becomes narrower. g On Performs compensation for camera shake using lens shift VR. Off Compensation is not performed. Notes About Movie VR • The effects of camera shake may not be completely eliminated in some situations. Enter shooting mode M d button M D menu icon M Wind noise reduction M k button Option Using Menus Wind Noise Reduction Description Y On Reduces the sound that is produced when wind passes over the microphone during movie recording. Other sounds may become difficult to hear during playback. Off (default setting) Wind noise reduction is disabled. 85 The Wi-Fi Options Menu Press the d button M J menu icon M k button Configure the Wi-Fi (wireless LAN) settings to connect the camera and a smart device. Option Description Connect to smart device Select when wirelessly connecting the camera and a smart device. See “Using the Wi-Fi (Wireless LAN) Function” (A100) for more information. Upload from camera Select when wirelessly connecting the camera and a smart device. See “Using the Wi-Fi (Wireless LAN) Function” (A100) for more information. • Before establishing the wireless connection, select the images to upload on the image selection screen (A82). After images are selected, the SSID and password of the camera are displayed on the screen. Disable Wi-Fi Select to terminate the wireless connection between the camera and a smart device. See “Using the Wi-Fi (Wireless LAN) Function” (A100) for more information. Using Menus SSID: Change the SSID. The SSID configured here is displayed on the smart device. Set a 1- to 24-character alphanumeric SSID. Options Auth./encryp.: Select whether or not to encrypt the communications between the camera and the connected smart device. Communications are not encrypted when Open (default setting) is selected. Password: Set the password. Set an 8- to 16-character alphanumeric password. Channel: Select the channel used for wireless connections. 86 Current settings Display the current settings. Restore default settings Restore the Wi-Fi settings to their default values. The wireless connection is terminated if this option is performed while Wi-Fi is connected. Operating the Text Input Keyboard • Use the multi selector HIJK to select alphanumeric characters. Press the k button to enter the selected character in the text field and move the cursor to the next space. • To move the cursor in the text field, select N or O on the keyboard, and press the k button. • To delete one character, press the l button. • To apply the setting, select P on the keyboard and press the k button. Text field SSID Back Delete Keyboard Using Menus 87 The Setup Menu Time Zone and Date Press the d button M z menu icon M Time zone and date M k button Set the camera clock. Option Date and time Description • Select a field: Press the multi selector JK. • Edit the date and time: Press HI. • Apply the setting: Select the minute setting and press the k button. Date and time Edit Using Menus Date format Select Year/Month/Day, Month/Day/Year, or Day/Month/ Year. Time zone Set time zone and daylight saving time. • When Travel destination (x) is set after having set the home time zone (w), the time difference between the travel destination and the home time zone is automatically calculated, and the date and time are saved for the selected region. Setting the Time Zone Use the multi selector HI to select Time zone and press the k button. Time zone and date Date and time Date format Time zone 1 5 / 1 1 / 2 0 1 5 1 5 :3 0 88 2 Select w Home time zone or x Travel destination and press the k button. • The date and time displayed in the monitor changes depending on whether the home time zone or travel destination is selected. Press K. Time zone Home time zone Travel destination 1 5 / 1 1 / 2 0 1 5 1 5 :3 0 Time zone Home time zone Travel destination 1 5 / 1 1 / 2 0 1 5 1 5 :3 0 Use JK to select the time zone. Back Using Menus • Press H to enable daylight saving time function, and W is displayed. Press I to disable the daylight saving time function. • Press the k button to apply the time zone. • If the correct time is not displayed for the home or travel destination time zone setting, set the appropriate time in Date and time. 89 Monitor Settings Press the d button M z menu icon M Monitor settings M k button Option Description Photo info Set whether or not to display information in the monitor. Image review Set whether or not to display the captured image immediately after shooting. • Default setting: On Brightness Adjust the brightness. • Default setting: 3 Photo Info Shooting mode Playback mode 4/4 Show info Using Menus 8m 0s 1400 Auto info (default setting) Hide info 90 0004. JPG 15/11/2015 15:30 The same information as shown in Show info is displayed, and it is hidden as shown in Hide info if no operations are performed for a few seconds. The information is displayed again when an operation is performed. Shooting mode Playback mode 4/4 Framing grid+auto info 8m 0s 1400 In addition to the information shown in Auto info, a framing grid is displayed to help frame pictures. The framing grid is not displayed while recording movies. 0004. JPG 15/11/2015 15:30 Same as Auto info. 4/4 8m 0s 1400 Movie frame+auto info 0004. JPG 15/11/2015 15:30 Same as Auto info. Using Menus In addition to the information shown in Auto info, a frame is displayed before movie recording begins that represents the area that will be captured when recording movies. The movie frame is not displayed while recording movies. 91 Date Stamp Press the d button M z menu icon M Date stamp M k button The shooting date and time can be stamped on images when shooting. The information can be printed even when using a printer that does not support the date imprinting function. 15.11.2015 Option Description f Date Date is stamped on images. S Date and time Date and time are stamped on images. Off (default setting) Date and time are not stamped on images. Notes About Date Stamp Using Menus • Stamped dates form a permanent part of image data and cannot be deleted. The date and time cannot be stamped on images after they have been captured. • The date and time cannot be stamped in the following situations: - When using Panorama assist scene mode - When shooting movies • The stamped date and time may be difficult to read when using a small image size. Printing a Shooting Date on Images Without a Date Stamp You can transfer images to a computer and use the ViewNX 2 software (A111) to imprint the shooting date on the images when they are printed. 92 Photo VR Press the d button M z menu icon M Photo VR M k button Select the vibration reduction setting used when shooting still images. Select Off when using a tripod to stabilize the camera during shooting. Option Description g On (default setting) Compensation for camera shake is performed using lens shift VR. Off Compensation is not performed. Notes About Photo VR • After turning on the camera or after switching from playback mode to shooting mode, wait for the shooting mode screen to be displayed completely before taking pictures. • Images in the camera monitor may be displayed blurry immediately after shooting. • The effects of camera shake may not be completely eliminated in some situations. Using Menus 93 AF Assist Press the d button M z menu icon M AF assist M k button Option Description a Auto (default setting) The AF-assist illuminator automatically lights up when you press the shutter-release button under dim lighting. The illuminator has a range of about #2.0# m (## ft # in.) at the maximum wide-angle position and about #1.5# m (## ft # in.) at the maximum telephoto position. • Note that for some scene modes or focus areas, the AF-assist illuminator may not light. Off The AF-assist illuminator does not light. Digital Zoom Press the d button M z menu icon M Digital zoom M k button Option Description Using Menus On (default setting) Digital zoom is enabled. Off Digital zoom is disabled. Notes About Digital Zoom • Digital zoom cannot be used in the following shooting modes: - Portrait, Night portrait, or Pet portrait scene mode - Smart portrait mode • Digital zoom cannot be used in other shooting modes when using certain settings (A49). 94 Sound Settings Press the d button M z menu icon M Sound settings M k button Option Description Button sound When On (default setting) is selected, the camera produces one beep when operations are performed, two beeps when focus is acquired on the subject, and three beeps when an error occurs. The start-up sound is also produced. • Sounds are disabled when using Pet portrait scene mode. Shutter sound When On (default setting) is selected, the shutter sound is produced when the shutter is released. • The shutter sound is not produced when using continuous shooting mode, when recording movies, or when using Pet portrait scene mode. Auto Off Set the amount of time that elapses before the camera enters standby mode (A12). You can select 30 s, 1 min (default setting), 5 min, or 30 min. Using Menus Press the d button M z menu icon M Auto off M k button Setting the Auto Off Function The time that passes before the camera enters standby mode is fixed in the following situations: • When a menu is displayed: 3 minutes (when auto off is set to 30 s or 1 min) • When shooting using Pet portrait auto release: 5 minutes (when auto off is set to 30 s or 1 min) • When shooting using Smile timer: 5 minutes (when auto off is set to 30 s or 1 min) • When the AC Adapter EH-62G is connected: 30 minutes • When an audio video cable is connected: 30 minutes 95 Format Card/Format Memory Press the d button M z menu icon M Format card/Format memory M k button Use this option to format a memory card or the internal memory. Formatting the memory cards or internal memory permanently deletes all data. Data that has been deleted cannot be recovered. Make sure to save important images to a computer before formatting. Formatting a Memory Card • Insert a memory card into the camera. • Select Format card in the setup menu and then press the k button. Formatting the Internal Memory • Remove the memory card from the camera. • Select Format memory in the setup menu and then press the k button. Using Menus 96 To start formatting, select Format on the screen that is displayed and press the k button. • Do not turn the camera off or open the battery-chamber/memory card slot cover during formatting. • This setting cannot be selected while Wi-Fi is connected. Language Press the d button M z menu icon M Language M k button Select a language for display of camera menus and messages. Video Mode Press the d button M z menu icon M Video mode M k button Adjust settings necessary for connection to a TV. Select from NTSC and PAL. Both NTSC and PAL are standards for analog color television broadcasting. • The available frame rates in Movie options (A83) vary depending on the video mode setting. Using Menus 97 Charge by Computer Press the d button M z menu icon M Charge by computer M k button Option Description a Auto (default setting) When the camera is connected to a computer that is running (A104), the battery inserted into the camera is automatically charged using power supplied by the computer. Off The battery inserted into the camera is not charged when the camera is connected to a computer. Notes About Charging with a Computer • When connected to a computer, the camera turns on and starts charging. If the camera is turned off, charging stops. • About 3 hours are required to charge a fully exhausted battery. Charging time increases when images are transferred while the battery is charging. • The camera turns off automatically if there is no communication with the computer for 30 minutes after the battery has finished charging. Using Menus 98 When the Charge Lamp Quickly Flashes Green Charging cannot be performed, possibly due to one of the reasons described below. • The ambient temperature is not suited to charging. Charge the battery indoors with an ambient temperature of 5°C to 35°C (41°F to 95°F). • The USB cable is not connected correctly, or the battery is faulty. Make sure the USB cable is connected correctly or replace the battery if necessary. • The computer is in sleep mode and is not supplying power. Wake up the computer. • The battery cannot be charged because the computer cannot supply power to the camera due to the computer’s settings or its specifications. Reset All Press the d button M z menu icon M Reset all M k button When Reset is selected, the camera’s settings are restored to their default values. • Some settings, such as Time zone and date or Language, are not reset. • This setting cannot be selected while Wi-Fi is connected. Resetting File Numbering To reset file numbering to “0001”, delete all images saved on the memory card or in the internal memory (A15) before selecting Reset all. Conformity Marking Press the d button M z menu icon M Conformity marking M k button View the standards with which the camera complies. Using Menus Firmware Version Press the d button M z menu icon M Firmware version M k button View the current camera firmware version. • This setting cannot be selected while Wi-Fi is connected. 99 Using the Wi-Fi (Wireless LAN) Function Functions That Can Be Performed Using Wi-Fi You can perform the following functions if you install the dedicated software “Wireless Mobile Utility” on your smart device that runs on Android OS or iOS, and connect it to the camera. Take Photos You can capture still images using the two methods described below. • Release the shutter on the camera and save the captured images to a smart device. • Use a smart device to remotely release the camera shutter and save images to the smart device. Using the Wi-Fi (Wireless LAN) Function View Photos Images that are saved in the camera’s memory card can be transferred and viewed on your smart device. You can also preselect the images in the camera that you want to transfer to your smart device. Installing the Software on the Smart Device Use your smart device to connect to the Google Play Store, App Store or other online apps marketplace and search for “Wireless Mobile Utility.” • Check the user’s manual provided with your smart device for further details. Check the description and other information and install the software. User’s Manual for Wireless Mobile Utility Download the user’s manual from the website below. • Android OS: http://nikonimglib.com/ManDL/WMAU/ • iOS: http://nikonimglib.com/ManDL/WMAU-ios/ To establish a connection with the camera, press the Z (Wi-Fi) button on the camera, and then turn on the Wi-Fi function of the smart device. Start the “Wireless Mobile Utility” after the connection is established. 100 Connecting the Smart Device to the Camera Press the Z (Wi-Fi) button on the camera. • The screen shown on the right is displayed. • If no connection confirmation is received from the smart device within three minutes, No access. is displayed and the camera returns to the Wi-Fi options screen. • You can also select Connect to smart device in the Wi-Fi options menu to display the screen shown on the right. Back Cancel Set the Wi-Fi setting on the smart device to On. • Check the user’s manual provided with your smart device for further details. • After the network names (SSIDs) that can be used for the smart device are displayed, select the SSID displayed on the camera. • When Auth./encryp. in the Wi-Fi options menu is set to WPA2-PSK-AES, the message for entering a password is displayed. Enter the password that is displayed on the camera. • When the camera is successfully connected to a Wi-Fi network, the shooting screen is displayed on the camera with the Wi-Fi communication indicator (A4). Start the “Wireless Mobile Utility” installed on the smart device. Using the Wi-Fi (Wireless LAN) Function Connect to smart device SSID: XXXXXXXXXXXXXXXXXX XXXXXX • The screen for selecting “Take photos” or “View photos” is displayed. • When the message “Cannot connect to camera.” is displayed, return to step 1 and retry the procedure. 101 C Touching an NFC-compatible Smart Device to the Camera for a Wi-Fi Connection When you use a smart device that is compatible with near field communication (NFC) functions, you can establish a Wi-Fi connection and start the “Wireless Mobile Utility” by touching the Y (N-Mark) on the smart device to the one on the camera. To Terminate the Wi-Fi Connection Perform one of the operations described below. • Turn off the camera. • Select Disable Wi-Fi in the Wi-Fi options menu on the camera (except when the camera is operated by remote control). • Set the Wi-Fi setting on the smart device to Off. Using the Wi-Fi (Wireless LAN) Function 102 Notes About Wi-Fi Connection • Wi-Fi connection operations are disabled in the following situations: - When the camera is connected to a TV, computer, or printer. - While recording movies - While the camera is processing data such as saving images or recording movies - When the camera is connected to a smart device • Select Disable Wi-Fi in areas where the use of radio waves is prohibited. • When Wi-Fi is connected, Auto off is disabled. • When Wi-Fi is connected, the battery drains faster than normal. Security Settings If no security settings (encryption and password) are configured for the camera’s Wi-Fi function, unauthorized third parties may access the network and cause harm. We strongly recommend performing the required security settings before using the Wi-Fi function. Use Options in the Wi-Fi options menu (A86) to perform the security settings. Preselecting Images in the Camera That You Want to Transfer to a Smart Device You can preselect images in the camera that you want to transfer to a smart device. Movies cannot be preselected for transfer. Select images to transfer. You can preselect the images to transfer to a smart device in the following menus: • Mark for Wi-Fi upload in the playback menu (A78) • Upload from camera in the Wi-Fi options menu (A86) When using Upload from camera, the SSID and password of the camera are displayed after images are selected. Connect the camera and smart device (A101). Preselecting Images to Transfer During Playback While the camera is in playback mode, press the Z (Wi-Fi) button or use the NFC function to establish a Wi-Fi connection, and preselect the displayed images that you want to transfer. • You can preselect one image at a time in full-frame playback mode. • In thumbnail playback mode, you can add one image that is selected by the cursor. • In calendar display mode, you can add all images that were shot on the date that is selected by the cursor. This operation is not available when you use Connect to smart device in the Wi-Fi options menu to establish the Wi-Fi connection. Using the Wi-Fi (Wireless LAN) Function After the camera and smart device are connected and the “Wireless Mobile Utility” starts, tap “View Photos” on the displayed confirmation screen to transfer the specified images to the smart device. 103 Connecting the Camera to a TV, Printer, or Computer You can enhance your enjoyment of images and movies by connecting the camera to a TV, printer, or computer. USB/audio/video output connector Open the connector cover. Connecting the Camera to a TV, Printer, or Computer 104 Insert the plug straight. • Before connecting the camera to an external device, make sure the remaining battery level is sufficient and turn the camera off. Before disconnecting, make sure to turn the camera off. • If the AC Adapter EH-62G (available separately) is used, this camera can be powered from an electrical outlet. Do not use any other make or model of AC adapter as it may cause the camera to heat up or malfunction. • For information about the connection methods and subsequent operations, refer to the documentation included with the device in addition to this document. Viewing images on a TV A106 Images and movies captured with the camera can be viewed on a TV. Connection method: Connect the video and audio plugs of an optional audio video cable to the TV’s input jacks. Printing images without using a computer A107 If you connect the camera to a PictBridge-compatible printer, you can print images without using a computer. Connection method: Connect the camera directly to the printer’s USB port with the USB cable. Viewing and organizing images on a computer A111 Connecting the Camera to a TV, Printer, or Computer You can transfer images to a computer to perform simple retouching and manage image data. Connection method: Connect the camera to the computer’s USB port with the USB cable. • Before connecting to a computer, install ViewNX 2 on the computer (A111). • If any USB devices that draw the power from the computer are connected, disconnect them from the computer before you connect the camera to it. Connecting the camera and other USB-powered devices to the same computer simultaneously may cause a camera malfunction or excessive power supply from the computer, which could damage the camera or memory card. 105 Connecting the Camera to a TV (Playback on a TV) Turn off the camera and connect it to the TV. • Connect the yellow plug to the video-in jack and the white plug to the audio-in jack on the TV. • Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them. Connecting the Camera to a TV, Printer, or Computer 106 Yellow Set the TV’s input to external video input. • See the documentation provided with your TV for details. Hold down the c (playback) button to turn on the camera. • Images are displayed on the TV. • The camera monitor does not turn on. White Connecting the Camera to a Printer (Direct Print) Users of PictBridge-compatible printers can connect the camera directly to the printer and print images without using a computer. Connecting the Camera to a Printer Turn on the printer. Turn off the camera and connect it to the printer using the USB cable. • Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them. The camera is automatically turned on. • The PictBridge startup screen (1) is displayed in the camera monitor, followed by the Print selection screen (2). Print selection 15/11/2015 Connecting the Camera to a TV, Printer, or Computer 107 B If the PictBridge Startup Screen Is Not Displayed When Auto is selected for Charge by computer (A98), it may be impossible to print images with direct connection of the camera to some printers. If the PictBridge startup screen is not displayed after the camera is turned on, turn the camera off and disconnect the USB cable. Set Charge by computer to Off and reconnect the camera to the printer. Printing Images One at a Time Use the multi selector JK to select the desired image and press the k button. Print selection 15/11/2015 • Move the zoom control toward f (h) to switch to thumbnail playback or g (i) to switch to full-frame playback. Connecting the Camera to a TV, Printer, or Computer Use HI to select Copies and press the k button. • Use HI to set the desired number of copies (up to nine) and press the k button. PictBridge 1 prints Start print Copies Paper size Select Paper size and press the k button. • Select the desired paper size and press the k button. • To print with the paper size setting configured on the printer, select Default. • The paper size options available on the camera vary depending on the printer that you use. Select Start print and press the k button. PictBridge 4 prints Start print Copies Paper size PictBridge • Printing starts. 4 prints Start print Copies Paper size 108 Printing Multiple Images When the Print selection screen is displayed, press the d (menu) button. Use the multi selector HI to select Paper size and press the k button. Select Print selection or Print all images and press the k button. Print menu Print selection Print all images Paper size Print menu Print selection Print all images Paper size Connecting the Camera to a TV, Printer, or Computer • Select the desired paper size and press the k button. • To print with the paper size setting configured on the printer, select Default. • The paper size options available on the camera vary depending on the printer that you use. • To exit the print menu, press the d button. Print selection 15/11/2015 109 Print selection Select images (up to 99) and the number Print selection 10 of copies (up to 9) of each. • Use the multi selector JK to select images, and use HI to specify the number of copies to be printed. • Images selected for printing are indicated by M and the number of Back copies to be printed. To cancel the print selection, set the number of copies to 0. • Move the zoom control toward g (i) to switch to full-frame playback or f (h) to switch to thumbnail playback. • Press the k button when setting is complete. When the screen for confirming the number of print copies is displayed, select Start print and press the k button to start printing. Print all images Connecting the Camera to a TV, Printer, or Computer 110 One copy each of all images saved in the internal memory, or on the memory card, is printed. • When the screen for confirming the number of print copies is displayed, select Start print and press the k button to start printing. Using ViewNX 2 (Transferring Images to a Computer) Installing ViewNX 2 ViewNX 2 is free software that enables you to transfer images and movies to your computer so that you can view, edit, or share them. To install ViewNX 2, download the ViewNX 2 installer from the website below and follow the onscreen installation instructions. http://nikonimglib.com/nvnx/ For system requirements and other information, see the Nikon website for your region. Transferring Images to a Computer Prepare a memory card that contains images. You can use any of the methods below to transfer images from the memory card to a computer. • SD memory card slot/card reader: Insert the memory card into the card slot of your computer or the card reader (commercially available) that is connected to the computer. • Direct USB connection: Turn the camera off and ensure that the memory card is inserted in the camera. Connect the camera to the computer using the USB cable. The camera automatically turns on. To transfer images that are saved in the camera’s internal memory, remove the memory card from the camera before connecting it to the computer. Connecting the Camera to a TV, Printer, or Computer 111 If a message is displayed prompting you to choose a program, select Nikon Transfer 2. • When using Windows 7 If the dialog shown at right is displayed, follow the steps below to select Nikon Transfer 2. 1 Under Import pictures and videos, click Change program. A program selection dialog will be displayed; select Import File using Nikon Transfer 2 and click OK. 2 Double-click Import File. If the memory card contains a large number of images, it may take a while for Nikon Transfer 2 to start. Wait until Nikon Transfer 2 starts. Notes About Connecting the USB Cable Connecting the Camera to a TV, Printer, or Computer Operation is not guaranteed if the camera is connected to the computer via a USB hub. After Nikon Transfer 2 starts, click Start Transfer. Start Transfer • Image transfer begins. When image transfer is complete, ViewNX 2 starts and the transferred images are displayed. • Consult online help for more information on using ViewNX 2. Terminate the connection. • If you are using a card reader or card slot, choose the appropriate option in the computer operating system to eject the removable disk corresponding to the memory card and then remove the memory card from the card reader or card slot. • If the camera is connected to the computer, turn the camera off and disconnect the USB cable. 112 Technical Notes Caring for the Product .................................................................................114 The Camera..............................................................................................114 The Battery...............................................................................................115 The Charging AC Adapter ..................................................................116 Memory Cards.........................................................................................117 Cleaning and Storage ..................................................................................118 Cleaning....................................................................................................118 Storage ......................................................................................................118 Error Messages ...............................................................................................119 Troubleshooting ............................................................................................123 File Names........................................................................................................130 Optional Accessories....................................................................................131 Specifications..................................................................................................132 Approved Memory Cards ...................................................................136 Index...................................................................................................................138 Technical Notes 113 Caring for the Product Observe the precautions described below in addition to the warnings in “For Your Safety” (Avi–viii) when using or storing the device. The Camera Do Not Apply Strong Impact to the Camera The product may malfunction if subjected to strong shock or vibration. In addition, do not touch or apply force to the lens or lens cover. Keep Dry The device will be damaged if immersed in water or subjected to high humidity. Avoid Sudden Changes in Temperature Sudden changes in temperature, such as when entering or leaving a heated building on a cold day, can cause condensation to form inside the device. To prevent condensation, place the device in a carrying case or a plastic bag before exposing it to sudden changes in temperature. Keep Away from Strong Magnetic Fields Do not use or store this device in the vicinity of equipment that generates strong electromagnetic radiation or magnetic fields. Doing so could result in loss of data or camera malfunction. Do Not Point the Lens at Strong Light Sources for Extended Periods Avoid pointing the lens at the sun or other strong light sources for extended periods when using or storing the camera. Intense light may cause the image sensor to deteriorate or produce a white blur effect in photographs. Turn the Product Off Before Removing or Disconnecting the Power Source or Memory Card Do not remove the battery while the product is on, or while images are being saved or deleted. Forcibly cutting power in these circumstances could result in loss of data or in damage to product memory or internal circuitry. Technical Notes 114 Notes About the Monitor • Monitors and electronic viewfinders are constructed with extremely high precision; at least 99.99% of pixels are effective, with no more than 0.01% being missing or defective. Hence while these displays may contain pixels that are always lit (white, red, blue, or green) or always off (black), this is not a malfunction and has no effect on images recorded with the device. • Images in the monitor may be difficult to see under bright lighting. • Do not apply pressure to the monitor, as this could cause damage or malfunction. Should the monitor break, care should be taken to avoid injury caused by broken glass and to prevent the liquid crystal from the display touching the skin or entering the eyes or mouth. Notes About Smear White or colored streaks may be visible when bright subjects are framed in the monitor. This phenomenon, known as “smear,” occurs when extremely bright light strikes the image sensor; it is characteristic of image sensors and does not indicate a malfunction. Smear may also take the form of partial discoloration in the monitor during shooting. It does not appear in images saved with the camera except in the cases of movies. When recording movies, we recommend that you avoid bright subjects such as the sun, reflected sunlight, and electric lights. The Battery Precautions for Use • Note that the battery may become hot after use. • Do not use the battery at ambient temperatures below 0°C (32°F) or above 40°C (104°F) as this could cause damage or malfunction. • If you notice any abnormalities such as excessive heat, smoke, or an unusual smell coming from the battery, immediately discontinue use and consult your retailer or Nikon-authorized service representative. • After removing the battery from the camera or optional battery charger, put the battery in a plastic bag, etc. in order to insulate it. Charging the Battery Technical Notes Check the battery level before using the camera and replace or charge the battery if necessary. • Charge the battery indoors with an ambient temperature of 5°C to 35°C (41°F to 95°F) before use. • A high battery temperature may prevent the battery from charging properly or completely, and may reduce battery performance. Note that the battery may become hot after use; wait for the battery to cool before charging. When charging the battery inserted into this camera using the Charging AC Adapter or a computer, the battery is not charged at battery temperatures below 0°C (32°F) or above 45°C (113°F). • Do not continue charging once the battery is fully charged as this will result in reduced battery performance. • The battery temperature may increase during charging. However, this is not a malfunction. 115 Carrying Spare Batteries Whenever possible, carry fully charged spare batteries when taking pictures on important occasions. Using the Battery When Cold On cold days, the capacity of batteries tends to decrease. If an exhausted battery is used at a low temperature, the camera may not turn on. Keep spare batteries in a warm place and exchange as necessary. Once warmed, a cold battery may recover some of its charge. Battery Terminals Dirt on the battery terminals may prevent the camera from functioning. Should the battery terminals become dirty, wipe them off with a clean, dry cloth before use. Charging an Exhausted Battery Turning the camera on or off while an exhausted battery is inserted in the camera may result in reduced battery life. Charge the exhausted battery before use. Storing the Battery • Always remove the battery from the camera or optional battery charger when it is not being used. Minute amounts of current are drawn from the battery while it is in the camera, even when not in use. This may result in excessive battery drain and complete loss of function. • Recharge the battery at least once every six months and completely exhaust it before returning it to storage. • Put the battery in a plastic bag, etc. in order to insulate it and store it in a cool place. The battery should be stored in a dry location with an ambient temperature of 15°C to 25°C (59°F to 77°F). Do not store the battery in hot or extremely cold locations. Battery Life A marked drop in the time a fully charged battery retains its charge, when used at room temperature, indicates that the battery needs to be replaced. Purchase a new battery. Recycling Used Batteries Replace the battery when it no longer holds a charge. Used batteries are a valuable resource. Please recycle used batteries in accordance with local regulations. Technical Notes 116 The Charging AC Adapter • The Charging AC Adapter EH-70P is for use only with compatible devices. Do not use with another make or model of device. • Do not, under any circumstances, use another make or model of AC adapter other than Charging AC Adapter EH-70P or USB-AC adapter. Failure to observe this precaution could result in overheating or in damage to the camera. • The EH-70P is compatible with AC 100–240 V, 50/60 Hz electrical outlets. When using in other countries, use a plug adapter (commercially available) as necessary. For more information about plug adapters, consult your travel agency. Memory Cards Precautions for Use • Use only Secure Digital memory cards. See “Approved Memory Cards” (A136) for recommended memory cards. • Be sure to follow the precautions described in the documentation included with the memory card. • Do not put labels or stickers on memory cards. Formatting • Do not format the memory card using a computer. • The first time you insert a memory card that has been used in another device into this camera, be sure to format it with this camera. We recommend formatting new memory cards with this camera before using them with this camera. • Note that formatting a memory card permanently deletes all images and other data on the memory card. Be sure to make copies of any images you wish to keep before formatting the memory card. • If the message Card is not formatted. Format card? is displayed when the camera is turned on, the memory card must be formatted. If there is data that you do not want to delete, select No. Copy the necessary data to a computer, etc. If you want to format the memory card, select Yes. The confirmation dialog will be displayed. To start formatting, press the k button. • Do not perform the following during formatting, while data is being written to or deleted from the memory card, or during data transfer to a computer. Failure to observe this precaution could result in the loss of data or in damage to the camera or memory card: - Open the battery-chamber/memory card slot cover to remove/insert the battery or memory card. - Turn off the camera. - Disconnect the AC adapter. Technical Notes 117 Cleaning and Storage Cleaning Do not use alcohol, thinner, or other volatile chemicals. Lens Avoid touching glass parts with your fingers. Remove dust or lint with a blower (typically a small device with a rubber bulb attached to one end that is pumped to produce a stream of air out the other end). To remove fingerprints or other stains that cannot be removed with a blower, wipe the lens with a soft cloth, using a spiral motion that starts at the center of the lens and working toward the edges. If this fails, clean the lens using a cloth lightly dampened with commercial lens cleaner. Monitor Remove dust or lint with a blower. To remove fingerprints and other stains, clean the monitor with a soft, dry cloth, being careful not to apply pressure. Body Use a blower to remove dust, dirt, or sand, then wipe gently with a soft, dry cloth. After using the camera at the beach or other sandy or dusty environment, wipe off any sand, dust, or salt with a dry cloth lightly dampened with fresh water and dry thoroughly. Note that foreign matter inside the camera could cause damage not covered by the warranty. Storage Technical Notes 118 Remove the battery if the camera will not be used for an extended period. To prevent mold or mildew, take the camera out of storage at least once a month. Turn the camera on and release the shutter a few times before putting the camera away again. Do not store the camera in any of the following locations: • Places that are poorly ventilated or subject to humidity of over 60% • Exposed to temperatures above 50°C (122°F) or below –10°C (14°F) • Next to equipment that produces strong electromagnetic fields, such as televisions or radios For storing the battery, follow the precautions in “The Battery” (A115) in “Caring for the Product” (A114). Error Messages Refer to the table below if an error message is displayed. Display Battery temperature is elevated. The camera will turn off. The camera will turn off to prevent overheating. Memory card is write protected. Cause/Solution The camera turns off automatically. Wait until the camera or battery temperature has cooled before resuming use. – The write-protect switch is in the “lock” position. Slide the write-protect switch to the “write” position. – This card cannot be used. An error occurred while accessing the memory card. • Use an approved memory card. This card cannot be read. • Check that the terminals are clean. • Confirm that the memory card is correctly inserted. 6, 136 Card is not formatted. Format card? The memory card has not been formatted for use in the camera. Formatting deletes all data saved on the memory card. If you need to keep copies of any images, make sure to select No and save the copies to a computer or other medium before formatting the memory card. Select Yes and press the k button to format the memory card. 117 Out of memory. Delete images or insert a new memory card. 6, 15 Technical Notes 119 Display Cause/Solution An error occurred while saving the image. Insert a new memory card or format the 96 memory card or internal memory. The camera has run out of file numbers. Insert a new memory card or format the memory card or internal memory. 96 There is insufficient space to save the copy. Delete images from the destination. 15 Image cannot be modified. Check that the images can be edited. 53, 128 Cannot record movie. A time-out error occurred while saving the movie on the memory card. Select a memory card with a faster write speed. 62, 136 Memory contains no images. There are no images in the internal memory or on the memory card. • Remove the memory card to play back images in the internal memory. • To copy the images saved in the camera’s internal memory to the memory card, press the d button to select Copy in the playback menu. Image cannot be saved. File contains no image data. This file cannot be played back. Technical Notes 120 81 The file was not created or edited with this camera. The file cannot be viewed on this camera. – View the file using a computer or the device used to create or edit this file. All images are hidden. There are no images available for a slide show, etc. 79 This image cannot be deleted. The image is protected. Disable protection. 80 Display Cause/Solution 86, 101 Could not connect. The camera failed to establish the connection while receiving the signals from the smart device. Set a different channel in Channel under Options in the Wi-Fi options menu, and establish the wireless connection again. 86, 101 Wi-Fi connection terminated. A cable was connected to the camera, a memory card was inserted or removed, or the connection was aborted due to poor connectivity. Disconnect the TV, computer, and printer from the camera and establish the wireless connection again. 86, 101 Lens error A lens error occurred. Turn the camera off and then on again. If the error persists, contact your retailer or Nikon-authorized service representative. 123 Communications error An error occurred while communicating with the printer. Turn the camera off and reconnect the USB cable. 107 System error An error occurred in the camera’s internal circuitry. Turn the camera off, remove and reinsert the battery, and turn the camera on. If the error persists, contact your retailer or Nikon-authorized service representative. 123 Technical Notes No access. The camera could not receive the signal from the smart device. Establish the wireless connection again. • Press the Z (Wi-Fi) button. • Touch an NFC-compatible smart device to the camera. • Select Connect to smart device in the Wi-Fi options menu. 121 Display Cause/Solution Printer error: check printer status. After solving the problem, select Resume and press the k button to resume printing.* – Printer error: check paper. Load the specified size of paper, select Resume, and press the k button to resume printing.* – Printer error: paper jam. Remove the jammed paper, select Resume, and press the k button to resume printing.* – Printer error: out of paper. Load the specified size of paper, select Resume, and press the k button to resume printing.* – Printer error: check ink. There is a problem with the printer’s ink. Check the ink, select Resume, and press the k button to resume printing.* – Printer error: out of ink. Replace the ink cartridge, select Resume, and press the k button to resume printing.* – Printer error: file corrupt. There is a problem with the image file to be printed. Select Cancel and press the k button to cancel printing. – * See the documentation provided with your printer for further guidance and information. Technical Notes 122 Troubleshooting If the camera fails to function as expected, check the list of common problems below before consulting your retailer or Nikon-authorized service representative. Power, Display, Settings Issues Problem Cause/Solution The camera is on but does not respond. Wait for recording to end. If the problem persists, turn the camera off. If the camera does not turn off, remove and reinsert the battery or batteries or, if you are using an AC adapter, disconnect and reconnect the AC adapter. Note that although any data currently being recorded will be lost, data that have already been recorded will not be affected by removing or disconnecting the power source. – The camera cannot be turned on. The battery is exhausted. 6, 7, 116 12 The camera turns off without warning. • The camera automatically turns off to save power (auto off function). • The camera and battery may not work properly at low temperatures. • The inside of the camera has become hot. Leave the camera off until the inside of the camera has cooled, and then try turning it on again. 12 The monitor is blank. • The camera is off. • The camera automatically turns off to save power (auto off function). • The flash lamp flashes while the flash is charging. Wait until charging is complete. • The camera is connected to a TV or computer. • The camera and smart device are connected using a Wi-Fi connection and the camera is being operated by remote control. The camera becomes hot. The camera may become hot when used for an extended period of time to shoot movies or when – used in a hot environment; this is not a malfunction. 115 – – Technical Notes – – 123 Cause/Solution The battery inserted in the camera cannot be charged. • Confirm all connections. • When connected to a computer, the camera may not charge for any of the reasons described below. - Off is selected for Charge by computer in the setup menu. - Battery charging stops if the camera is turned off. - Battery charging is not possible if the camera’s display language and date and time have not been set, or the date and time were reset after the camera’s clock battery was exhausted. Use the Charging AC Adapter to charge the battery. - Battery charging may stop when the computer enters sleep mode. - Depending on the computer specifications, settings, and status, battery charging may not be possible. The monitor is hard to read. • Adjust the monitor brightness. • The monitor is dirty. Clean the monitor. 90 118 O flashes on the screen. • If the camera clock has not been set, O flashes on the shooting screen, and images and movies saved before the clock is set are dated “00/00/ 0000 00:00” and “01/01/2015 00:00” respectively. Set the correct time and date for Time zone and date in the setup menu. • The camera clock is not as accurate as ordinary watches or clocks. Periodically compare the time of the camera clock with that of a more accurate timepiece, and reset as required. 4, 88 No indicators displayed in monitor. Hide info is selected for Photo info in Monitor settings in the setup menu. 90 Date stamp not available. Time zone and date has not been set in the setup menu. 88 Date and time of recording are not correct. Technical Notes 124 Problem Date not stamped • The current shooting mode does not support on images even Date stamp. when Date • The date cannot be stamped on movies. stamp is enabled. 64, 98 – 9, 10 – – 92 Problem Screen for setting time zone and date is displayed when the camera is turned on. Cause/Solution The clock battery is exhausted; all settings were restored to their default values. 9, 10 When Autofocus mode is set to Full-time AF or while in some shooting modes, the camera may produce an audible focusing sound. 17, 75, 84 The camera settings reset. The camera makes sound. Shooting Issues Problem Cause/Solution Cannot switch to shooting mode. The camera cannot be switched to shooting mode while connected to a power outlet via the Charging AC Adapter. 1, 14 Cannot take pictures or record movies. • When the camera is in playback mode, press the A button, Shutter-release button, or b (e) button. • When menus are displayed, press the d button. • The flash is charging while the flash lamp is flashing. • The battery is exhausted. The camera cannot focus. • The subject is too close. Try shooting using scene auto selector mode, Close-up scene mode, or macro mode. • The subject is hard to focus on. • Set AF assist in the setup menu to Auto. • Turn the camera off and then on again. 17, 18, 19, 21, 39 46 94 – Images are blurred. • Use the flash. • Increase the ISO sensitivity value. • Use Photo VR when taking still images, and use Movie VR when recording movies. • Use a tripod to stabilize the camera (using the self-timer at the same time is more effective). 35 71 85, 93 104 64 35 6, 7, 116 Technical Notes 37 125 Technical Notes 126 Problem Cause/Solution Streaks of light or partial discoloration are visible in the monitor. Smear may occur when extremely bright light strikes the image sensor. When recording movies, avoiding bright objects, such as the sun, reflections of the sun, and electric lights is recommended. 62, 115 Bright specks appear in images captured with flash. The flash is reflecting off particles in the air. Set the flash mode setting to W (off). 35 Flash does not fire. • The flash mode is set to W (off). • A scene mode that restricts the flash is selected. • A function that restricts the flash is enabled. 35 41 48 Optical zoom cannot be used. Optical zoom cannot be used while recording movies. 62 Digital zoom cannot be used. • Digital zoom is set to Off in the setup menu. • Digital zoom cannot be used with certain shooting modes or when using certain settings in other functions. 94 49, 94 Image mode not available. A function that restricts Image mode is enabled. 48 No sound when the shutter is released. Off is selected for Shutter sound in Sound settings in the setup menu. No sound is produced with some shooting modes and settings, even when On is selected. 95 AF-assist illuminator does not light. Off is selected for AF assist in the setup menu. AFassist illuminator may not light depending on the position of the focus area or the current scene mode, even when Auto is selected. 94 Images appear smeared. The lens is dirty. Clean the lens. 118 Colors are unnatural. White balance or hue is not adjusted properly. 22, 68 Randomly spaced bright pixels (“noise”) appear in image. The subject is dark and the shutter speed is too slow, or ISO sensitivity is too high. Noise can be reduced by: • Using the flash • Specifying a lower ISO sensitivity setting 35 71 A Problem Cause/Solution Randomly spaced bright pixels (“noise”) appear in movies. When recording movies in dim lighting, the image may contain noise. This occurs when the ISO sensitivity increases, and it does not indicate a malfunction. – • • • • • • 35 11 133 40 71 22, 35 Images are too dark (underexposed). The flash mode is set to W (off). The flash window is blocked. The subject is beyond the range of the flash. Adjust exposure compensation. Increase ISO sensitivity. The subject is backlit. Select Backlighting scene mode or set the flash mode setting to X (fill flash). Images are too bright (overexposed). Adjust exposure compensation. 40 Unexpected results when flash set to V (auto with red-eye reduction). Use any scene mode other than Night portrait, and change the flash mode to any setting other than V (auto with red-eye reduction) and try taking the picture again. 35, 41 Skin tones are not softened. • In some shooting conditions, facial skin tones may not be softened. • For images containing four or more faces, try using the Skin softening effect in Glamour retouch in the playback menu. Saving images takes time. It may take more time to save images in the following situations: • When the noise reduction function is in operation, such as when shooting in a dark environment • When the flash mode is set to V (auto with red-eye reduction) • When the skin softening function is applied while shooting • When using continuous shooting mode 56 – 36 44, 76 70 – Technical Notes Colored circles or light streaks appear in the monitor or images. When shooting with backlighting or when a very strong light source (such as sunlight) is in the frame, colored circles or light streaks (ghosting) may occur. Change the position of the light source, or frame the image so that the light source does not enter the frame, and try again. 44 127 Playback Issues Problem File cannot be played back. – Cannot zoom in on image. • Playback zoom cannot be used with movies. • For small images, the magnification rate displayed on the screen may not be compatible with the actual magnification rate. • This camera may not be able to zoom in on images captured with another make or model of digital camera. – 26, 53 Cannot edit images. • Some images cannot be edited. Images that have already been edited may not be edited again. • There is not enough free space on the memory card or in the internal memory. • This camera is unable to edit images captured with other cameras. • Editing functions used for images are not available for movies. • Video mode is not correctly set in the setup menu. • The memory card contains no images. • Remove the memory card to play back images in the internal memory. 64, 97 • • • • • – 98, 104 104, 111 – – Images are not displayed on TV. Technical Notes 128 Cause/Solution • This camera may not be able to play back images saved with another make or model of digital camera. • This camera cannot play back movies recorded with another make or model of digital camera. • This camera may not be able to play back data edited on a computer. Nikon Transfer 2 does not start when the camera is connected to a computer. The camera is off. The battery is exhausted. The USB cable is not correctly connected. The camera is not recognized by the computer. The computer is not set to start Nikon Transfer 2 automatically. For more information about Nikon Transfer 2, refer to help information contained in ViewNX 2. – – – – A Problem Cause/Solution The PictBridge startup screen is not displayed when the camera is connected to a printer. With some PictBridge-compatible printers, the PictBridge startup screen may not be displayed and it may be impossible to print images when Auto is selected for Charge by computer in the setup menu. Set Charge by computer to Off and reconnect the camera to the printer. 64, 98 Images to be printed are not displayed. • The memory card contains no images. • Remove the memory card to print images in the internal memory. – Cannot select paper size with the camera. The camera cannot be used to select the paper size in the following situations, even when printing from a PictBridge-compatible printer. Use the printer to select the paper size. • The printer does not support the paper sizes specified by the camera. • The printer automatically selects the paper size. – Technical Notes 129 File Names Images or movies are assigned file names as follows. File name: DSCN 0001 .JPG (1) (2) (3) Technical Notes 130 (1) Identifier Not shown on the screen of the camera. • DSCN: Original still images, movies • SSCN: Small picture copies • RSCN: Cropped copies • FSCN: Images created by an image editing function other than crop and small picture (2) File number Assigned in ascending order, starting with “0001” and ending with “9999.” (3) Extension Indicates file format. • .JPG: Still images • .AVI: Movies Optional Accessories Battery charger Battery Charger MH-66 It takes about 1 hour and 50 minutes to charge a fully exhausted battery. AC Adapter EH-62G (connect as shown) AC adapter Make sure that the power connector cable is fully inserted in the power connector slot before inserting the AC adapter into the battery chamber. In addition, make sure that the power connector cable is fully inserted in the battery chamber slot before closing the battery-chamber/memory card slot cover. If part of the cable protrudes from the slots, the cover or cable may be damaged when the cover is closed. Audio Video Cable EG-CP14 Availability may vary with country or region. See our website or brochures for the latest information. Technical Notes Audio video cable 131 Specifications Nikon COOLPIX S3700 Digital Camera Type Compact digital camera Number of effective pixels 20.1 million (Image processing may reduce the number of effective pixels.) Image sensor 1/2.3-in. type CCD; approx. 20.48 million total pixels Lens NIKKOR lens with 8× optical zoom Focal length 4.5–36.0 mm (angle of view equivalent to that of 25–200 mm lens in 35mm [135] format) f/-number f/3.7–6.6 Construction Up to 4× (angle of view equivalent to that of approx. 800 mm lens in 35mm [135] format) Vibration reduction Lens shift (still images) Lens shift and electronic VR (movies) Autofocus (AF) Contrast-detect AF Focus range • [W]: Approx. 50 cm (1 ft 8 in.)–, [T]: Approx. 1.5 m (5 ft)– • Macro mode: Approx. 2 cm (# in.)– (wide-angle position) (All distances measured from center of front surface of lens) Focus-area selection Face priority, center, manual with 99 focus areas, subject tracking, target finding AF Monitor Technical Notes 132 9 elements in 7 groups Digital zoom magnification 6.7 cm (2.7-in.), approx. 230k-dot, TFT LCD with antireflection coating and 5-level brightness adjustment Frame coverage (shooting mode) Approx. 97% horizontal and vertical (compared to actual picture) Frame coverage (playback mode) Approx. 99% horizontal and vertical (compared to actual picture) Storage Media Internal memory (approx. 25 MB), SD/SDHC/SDXC memory card File system DCF and Exif 2.3 compliant File formats Still images: JPEG Movies: AVI (Motion-JPEG compliant) Image size (pixels) • • • • • • • • ISO sensitivity (Standard output sensitivity) • ISO 80–1600 • ISO 3200 (available when using Auto mode) 20M (High) [5152 × 3864P] 20M [5152 × 3864] 10M [3648 × 2736] 4M [2272 × 1704] 2M [1600 × 1200] VGA [640 × 480] 16:9 (14M) [5120 × 2880] 1:1 [3864 × 3864] Exposure Metering mode Matrix, center-weighted (digital zoom less than 2×), spot (digital zoom 2× or more) Exposure control Programmed auto exposure and exposure compensation (–2.0 – +2.0 EV in steps of 1/3 EV) Shutter Speed Aperture Range Self-timer Mechanical and CCD electronic shutter • 1/1500–1 s • 4 s (Fireworks show scene mode) Electronically-controlled ND filter (–3 AV) selection 2 steps (f/3.7 and f/10.5 [W]) Can be selected from 10 s and 2 s Flash [W]: 0.5–#.# m (## ft # in.–## ft # in.) [T]: 1.5–#.# m (## ft # in.–## ft # in.) Flash control TTL auto flash with monitor preflashes Technical Notes Range (approx.) (ISO sensitivity: Auto) 133 Interface USB connector Hi-Speed USB • Supports Direct Print (PictBridge) • Also used as audio/video output connector (NTSC or PAL can be selected for video output.) Wi-Fi (Wireless LAN) Standards IEEE 802.11b/g/n (standard wireless LAN protocol) Communications protocols IEEE 802.11b: DBPSK/DQPSK/CCK IEEE 802.11g: OFDM IEEE 802.11n: OFDM Range (line of sight) Approx. 10 m (11 yd) Operating frequency 2412–2462 MHz (1-11 channels) Data rates (actual measured values) IEEE 802.11b: 5 Mbps IEEE 802.11g: 20 Mbps IEEE 802.11n: 20 Mbps Security WPA2 Access protocols Infrastructure Supported languages Arabic, Bengali, Bulgarian, Chinese (Simplified and Traditional), Czech, Danish, Dutch, English, Finnish, French, German, Greek, Hindi, Hungarian, Indonesian, Italian, Japanese, Korean, Marathi, Norwegian, Persian, Polish, Portuguese (European and Brazilian), Romanian, Russian, Serbian, Spanish, Swedish, Tamil, Telugu, Thai, Turkish, Ukrainian, Vietnamese Power sources One Rechargeable Li-ion Battery EN-EL19 (included) AC Adapter EH-62G (available separately) Charging time Approx. 2 h 40 min (when using Charging AC Adapter EH-70P and when no charge remains) Battery life1 Technical Notes 134 Still images Approx. 230 shots when using EN-EL19 Movies (actual battery life for recording)2 Approx. 45 min when using EN-EL19 Tripod socket 1/4 (ISO 1222) Dimensions (W × H × D) Approx. 95.9 × 58.0 × 20.1 mm (3.8 × 2.3 × 0.8 in.) (excluding projections) Weight Approx. 130 g (4.6 oz) (including battery and memory card) Operating environment Temperature 0°C–40°C (32°F–104°F) Humidity 85% or less (no condensation) • Unless otherwise stated, all figures assume a fully-charged battery and an ambient temperature of 23 ±3°C (73.4 ±5.4°F) as specified by the Camera and Imaging Products Association (CIPA). Battery life may vary depending on conditions of use, such as the interval between shots or the length of time that menus and images are displayed. Individual movie files cannot exceed 2 GB in size or 29 minutes in length. Recording may end before this limit is reached if camera temperature becomes elevated. Rechargeable Li-ion Battery EN-EL19 Type Rechargeable lithium-ion battery Rated capacity DC 3.7 V, 700 mAh Operating temperature 0°C–40°C (32°F–104°F) Dimensions (W × H × D) Approx. 31.5 × 39.5 × 6 mm (1.3 × 1.6 × 0.3 in.) Weight Approx. 14.5 g (0.5 oz) Charging AC Adapter EH-70P AC 100–240 V, 50/60 Hz, 0.07–0.044 A Rated output DC 5.0 V, 550 mA Operating temperature 0°C–40°C (32°F–104°F) Dimensions (W × H × D) Approx. 55 × 22 × 54 mm (2.2 × 0.9 × 2.2 in.) (excluding plug adapter) For Argentina: Approx. 55 × 59 × 63 mm (2.2 × 2.4 × 2.5 in.) Weight Approx. 47 g (1.7 oz) (excluding plug adapter) For Argentina: Approx. 72 g (2.6 oz) • Nikon will not be held liable for any errors this manual may contain. • The appearance of this product and its specifications are subject to change without notice. Technical Notes Rated input 135 Approved Memory Cards The following Secure Digital (SD) memory cards have been tested and approved for use in this camera. • Memory cards with an SD Speed Class rating of 6 or faster are recommended for recording movies. When using a memory card with a lower Speed Class rating, movie recording may stop unexpectedly. SDXC memory card SD memory card SDHC memory card SanDisk – 4 GB, 8 GB, 16 GB, 32 GB 64 GB, 128 GB TOSHIBA – 4 GB, 8 GB, 16 GB, 32 GB 64 GB 4 GB, 8 GB, 16 GB, 32 GB 64 GB 8 GB, 16 GB, 32 GB 64 GB, 128 GB Panasonic Lexar 2 GB – • Contact the manufacturer for details on the above cards. We cannot guarantee camera performance when using memory cards made by other manufacturers. • If you use a card reader, make sure that it is compatible with your memory card. Trademark Information • Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. • Adobe, the Adobe logo, and Reader are either trademarks or registered trademarks of Adobe Systems Incorporated in the United States and/or other countries. • SDXC, SDHC, and SD Logos are trademarks of SD-3C, LLC. Technical Notes 136 • PictBridge is a trademark. • Wi-Fi and the Wi-Fi logo are trademarks or registered trademarks of the Wi-Fi Alliance. • Android and Google Play are trademarks or registered trademarks of Google, Inc. • The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. • All other trade names mentioned in this manual or the other documentation provided with your Nikon product are the trademarks or registered trademarks of their respective holders. AVC Patent Portfolio License This product is licensed under the AVC Patent Portfolio License for the personal and non-commercial use of a consumer to (i) encode video in compliance with the AVC standard (“AVC video”) and/or (ii) decode AVC video that was encoded by a consumer engaged in a personal and noncommercial activity and/or was obtained from a video provider licensed to provide AVC video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, L.L.C. See http://www.mpegla.com. FreeType License (FreeType2) • Portions of this software are copyright © 2012 The FreeType Project (http://www.freetype.org). All rights reserved. MIT License (HarfBuzz) • Portions of this software are copyright © 2015 The HarfBuzz Project (http://www.freedesktop.org/wiki/Software/HarfBuzz). All rights reserved. Technical Notes 137 Index Symbols Technical Notes x Scene auto selector mode ................................................................. 17, 19 C Scene mode ........................... 17, 20 R Special effects mode .......... 17, 27 F Smart portrait mode.......... 17, 29 A Auto mode.............................. 17, 33 c Playback mode.............................. 14 C List by date mode......................... 52 J Wi-Fi options menu.......... 64, 86 z Setup menu ............................. 64, 88 g (Telephoto)................................. 13, 14 f (Wide-angle)............................ 13, 14 i Playback zoom ........................ 14, 50 h Thumbnail playback.......... 14, 51 j Help....................................................... 20 A Shooting mode button...... 2, 17 c Playback button ..................... 2, 14 b (e movie-record) button .................................................................... 2, 18 k Apply selection button ................ 2 d Menu button......................... 2, 64 l Delete button.............................. 2, 15 Z (Wi-Fi) button .............. 1, 100, 101 Y N-Mark ........................................ 2, 102 m Flash mode ................................. 18, 35 n Self-timer.................................... 18, 37 p Macro mode............................ 18, 39 o Exposure compensation ................................................................ 18, 40 R .................................................. 25 AC adapter ................................. 104, 131 AF area mode ......................................... 72 AF assist................................................ 1, 94 Aperture value ....................................... 13 138 Audio video cable ...... 105, 106, 131 Auto flash ................................................. 36 Auto mode ...................................... 17, 33 Auto off.............................................. 12, 95 Auto with red-eye reduction ....... 36 Autofocus............................... 62, 75, 84 Autofocus mode......................... 75, 84 Backlighting o............................ 20, 22 Battery ................................... 6, 7, 10, 135 Battery chamber................................. 131 Battery charger............................... 8, 131 Battery latch............................................... 6 Battery level indicator........................ 10 Battery-chamber/memory card slot cover................................................................ 2 Beach Z................................................... 20 Blink proof................................................ 77 Brightness................................................. 90 Built-in microphone............................... 1 Button sound ......................................... 95 Calendar Display ................................... 51 Charge by computer......................... 98 Charge lamp............................................... 2 Charging .............................................. 7, 98 Charging AC Adapter................ 7, 135 Close-up k..................................... 20, 21 Cloudy ........................................................ 68 Compression ratio............................... 66 Computer..................................... 105, 111 Conformity Marking........................... 99 Connecting to smart devices...... 86, 101 Connector cover ...................................... 1 Continuous .............................................. 70 Copying images.................................... 81 Creative Slider ........................................ 33 Crop.............................................................. 59 Cross process o.................................. 27 Current settings ................................... 86 Date and time .................................. 9, 88 Date format........................................ 9, 88 Date stamp............................................... 92 Daylight..................................................... 68 Daylight saving time ............ 9, 10, 88 Delete.......................................................... 15 Digital zoom................................... 13, 94 Direct print ............................................ 107 Disable Wi-Fi .......................................... 86 D-Lighting ................................................ 55 Dusk/dawn i ....................................... 20 Dynamic Fine Zoom........................... 13 Editing images ....................................... 53 EH-70P...................................................... 135 EN-EL19 ................................................... 135 Exposure compensation................. 40 Eyelet for camera strap......................... 1 Glamour retouch ........................ 29, 56 Help.............................................................. 20 High-contrast monochrome F ........................................................................ 27 Image mode ........................................... 66 Image review.......................................... 90 Image size ................................................ 66 Incandescent.......................................... 68 Internal memory ..................................... 6 Internal memory indicator........... 3, 5 Interval ....................................................... 76 ISO sensitivity .......................................... 71 Landscape c ........................................ 20 Language.................................................. 97 Lens....................................................... 1, 132 Lens cover.................................................... 1 List by date mode ............................... 52 Technical Notes Face detection ...................................... 43 Face priority............................................. 72 File names.............................................. 130 Fill flash....................................................... 36 Fireworks show m ..................... 20, 22 Firmware version................................. 99 Fixed range auto................................... 71 Flash ........................................................ 1, 35 Flash lamp .......................................... 2, 35 Flash mode ..................................... 35, 36 Flash off ...................................................... 36 Fluorescent.............................................. 68 Focus........................................................... 72 Focus area ................................................ 43 Focus indicator ................................. 3, 12 Focus lock ................................................ 47 Food u.............................................. 20, 22 Format internal memory................. 96 Format memory cards................ 6, 96 Formatting......................................... 6, 96 Full-frame playback............................ 50 Full-time AF.................................... 75, 84 Functions that cannot be used simultaneously...................................... 48 Macro mode ........................................... 39 Mark for Wi-Fi upload............. 78, 103 139 Memory card............................. 117, 136 Memory card slot .................................... 6 Monitor.......................................... 2, 3, 118 Monitor settings .................................. 90 Movie menu .................................. 64, 83 Movie options ........................................ 83 Movie playback ............................ 18, 63 Movie recording .......................... 18, 60 Movie VR.................................................... 85 Multi selector .................................... 2, 64 NFC ............................................................ 102 Night landscape j ................... 20, 21 Night portrait e................................... 20 Nikon Transfer 2 .................................. 112 Nostalgic sepia E .............................. 27 Number of exposures remaining ................................................................ 10, 67 Number of shots................................... 76 Optical zoom .......................................... 13 Optional accessories ........................ 131 Options...................................................... 86 Technical Notes 140 Panorama assist playback............... 26 Panorama assist U.................. 20, 24 Paper size ................................... 108, 109 Party/indoor f............................ 20, 21 Pet portrait auto release .................. 23 Pet portrait O............................... 20, 23 Photo info ................................................ 90 Photo VR .................................................... 93 PictBridge.................................... 105, 107 Playback ..................................................... 14 Playback menu ............................ 64, 78 Playback mode ...................................... 14 Playback zoom.............................. 14, 50 Pop l ..................................................... 27 Portrait b................................................. 20 Power switch.............................................. 1 Power-on lamp ......................................... 1 Preset manual........................................ 69 Pressing halfway ................................... 13 Print..................................... 105, 108, 109 Printer ........................................... 105, 107 Protect........................................................ 80 Quick effects............................................ 53 Quick retouch ........................................ 54 Rechargeable Li-ion battery ....... 135 Red-eye correction .............................. 55 Remaining movie recording time ................................................................ 60, 61 Reset all...................................................... 99 Restore default settings................... 86 Rotate image.......................................... 80 Scene mode............................................ 20 SD memory card ..................... 117, 136 Selective color I................................ 27 Self-collage............................................... 31 Self-timer .................................................. 37 Self-timer lamp ................................ 1, 38 Setup menu ................................... 64, 88 Shooting ............................................ 11, 17 Shooting menu............................ 64, 66 Shooting mode ..................................... 17 Shutter sound............................... 76, 95 Shutter speed ......................................... 13 Shutter-release button......................... 1 Single .......................................................... 70 Single AF .......................................... 75, 84 Skin softening ........................................ 44 Slide show ................................................ 79 Slow sync .................................................. 36 Small picture ........................................... 58 Smart portrait menu................. 64, 76 Smart portrait mode .......................... 29 Smile timer............................................... 30 Snow z..................................................... 20 Soft D........................................................ 27 Sound settings....................................... 95 Speaker.......................................................... 2 Special effects mode.......................... 27 Sports d........................................... 20, 21 Strap ................................................................ ii Subject tracking ........................... 73, 74 Sunset h.................................................. 20 Wide-angle ............................................... 13 Wi-Fi button.......................... 1, 100, 101 Wi-Fi options menu .................. 64, 86 Wind noise reduction ....................... 85 Wireless LAN........................................ 100 Wireless Mobile Utility................... 100 Zoom control..................................... 1, 13 Zooming in/out..................................... 13 Target finding AF......................... 45, 73 Telephoto ................................................. 13 Televisions ................................. 105, 106 Thumbnail display....................... 14, 51 Time difference .................................... 88 Time zone ........................................ 10, 88 Time zone and date...................... 9, 88 Toy camera effect 1 m.................... 27 Toy camera effect 2 n ................... 27 Tripod socket ................................. 2, 134 Video mode ............................................. 97 ViewNX 2 ................................................. 111 Volume ....................................................... 63 Technical Notes Upload from camera......................... 86 USB cable .................... 7, 105, 107, 111 USB/audio/video output connector ............................................................................. 1 White balance ....................................... 68 141 No reproduction in any form of this manual, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from NIKON CORPORATION. YP4K01(11) 6MN53311-01
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 77 Creator : pdfsam-console (Ver. 2.4.0e) Producer : iText 2.1.7 by 1T3XT Modify Date : 2015:01:13 17:24:21+08:00 Create Date : 2015:01:13 17:24:21+08:00EXIF Metadata provided by EXIF.tools