Nikon 6MB12911 03 User Manual To The 843b73e6 F8b8 446d A930 B7a619af1bae

User Manual: Nikon 6MB12911-03 to the manual

Open the PDF directly: View PDF PDF.
Page Count: 484 [warning: Documents this large are best viewed by clicking the View PDF Link!]

DIGITAL CAMERA
En
User's Manual
Printed in Japan
SB2G03(11)
6MB12911-03
No reproduction in any form of this manual, in whole or in part
(except for brief quotation in critical articles or reviews), may be
made without written authorization from NIKON CORPORATION.
En
Thank you for your purchase of a Nikon single-lens reflex (SLR) digital
camera.
To get the most from your camera, please be sure to read all
instructions thoroughly and keep them where they will be read by all
those who use the product.
Symbols and Conventions
To make it easier to find the information you need, the following symbols
and conventions are used:
Menu items, options, and messages displayed in the camera monitor are
shown in bold.
Camera Settings
The explanations in this manual assume that default settings are used.
Help
Use the camera’s on-board help feature for help on menu items and other
topics.
See page 22 for details.
Digitutor
Digitutor, a series of “watch and learn” manuals in movie form, is available
from the following website:
http://www.nikondigitutor.com/index_eng.html
This icon marks cautions; information that should be read before
use to prevent damage to the camera.
D
This icon marks notes; information that should be read before
using the camera.
A
This icon marks references to other pages in this manual.
0
AFor Your Safety
Before using the camera for the first time, read the safety
instructions in “For Your Safety” (0xiii–xv).
i
Where to Find It
Find what you’re looking for from:
The Table of Contents.............................................................. 0iv
The Q&A Index ......................................................................... 0ii
The Quick Start Guide ............................................................. 0xxii
The Index.................................................................................. 0449
Error Messages ........................................................................ 0424
Troubleshooting...................................................................... 0419
i
i
i
i
i
i
XIntroduction 01
sTutorial 019
xLive View Photography 049
yMovie Live View 063
dImage Recording Options 085
NFocus 097
kRelease Mode 0111
SISO Sensitivity 0117
ZExposure 0123
rWhite Balance 0153
JImage Enhancement 0173
lFlash Photography 0191
tOther Shooting Options 0207
IMore About Playback 0235
eVoice Memos 0255
QConnections 0263
UMenu Guide 0283
nTechnical Notes 0385
ii
Find what you’re looking for using this “question and answer”
index.
Q&A Index
Taking Photographs 0
Shooting and Framing Options
Is there a quick and easy way to take snapshots? xxii, 40
Can I frame photos in the monitor (Clive view
photography)? 49
Can I shoot movies (1movie live view)? 63
Can I join photographs taken at regular intervals to
create a time-lapse movie? 223
Release Modes
Can I take photos in quick succession? 111
How do I take pictures with the self-timer? 114
Focus
Can I choose how the camera focuses? 97
Can I choose the focus point? 103
Exposure
Can I make photos brighter or darker? 137
How do I preserve details in shadows and highlights? 184,
186
Image Quality and Size
How do I take pictures for printing at large sizes? 90, 93
How can I get more pictures on the memory card?
Viewing Photographs 0
Playback
How do I view photographs on the camera? 235
How do I view more information about a photo? 238
Can I view photos in an automatic slide show? 291
Can I view photos on a TV? 280
Can I protect photos from accidental deletion? 249
Deletion
How do I delete unwanted photos? 251
i
i
i
i
i
i
i
iii
Retouching Photographs 0
How do I create retouched copies of photos? 361
How do I make JPEG copies of RAW (NEF) photos? 372
Can I trim movie footage on the camera or save
movie stills? 79
Menus and Settings 0
How do I use the menus? 19
How do I keep the displays from turning off? 316, 317
How do I focus the viewfinder? 38
How do I set the camera clock? 30, 348
How do I format memory cards? 36
How do I restore default settings? 207, 295,
305
How do I get help for a menu or message? 22
Connections 0
How do I copy photos to a computer? 263
How do I print photos? 271
Can I print the date of recording on my photos? 274
Maintenance and Optional Accessories 0
What memory cards can I use? 442
What lenses can I use? 385
What optional flash units (Speedlights) can I use? 192
What other accessories are available for my camera? 391
What software is available for my camera?
How do I clean the camera? 398
Where should I take my camera for servicing and
repairs? 405
iv
Q&A Index .................................................................................................ii
For Your Safety .................................................................................... xiii
Notices.................................................................................................... xvi
Quick Start Guide............................................................................... xxii
Introduction 1
Package Contents...................................................................................1
Getting to Know the Camera..............................................................2
Camera Body.......................................................................................2
The Top Control Panel ..................................................................... 7
The Rear Control Panel.................................................................... 9
The Viewfinder Display..................................................................11
The Information Display................................................................13
The BS-2 Accessory Shoe Cover .................................................17
Tutorial 19
Camera Menus...................................................................................... 19
Using Camera Menus .....................................................................20
Help ......................................................................................................22
First Steps ............................................................................................... 23
Charge the Battery ..........................................................................23
Insert the Battery .............................................................................25
Attach a Lens.....................................................................................28
Basic Setup.........................................................................................30
Insert a Memory Card.....................................................................33
Format the Memory Card .............................................................36
Adjust Viewfinder Focus ...............................................................38
Basic Photography and Playback................................................... 40
Turn the Camera On .......................................................................40
Ready the Camera ...........................................................................42
Table of Contents
v
Focus and Shoot.............................................................................. 43
Viewing Photographs.................................................................... 46
Deleting Unwanted Photographs............................................. 47
Live View Photography 49
Focusing in Live View .................................................................... 52
The Live View Display: Live View Photography ...................55
The Information Display: Live View Photography............... 58
Manual Focus ................................................................................... 59
Live View Shutter Release Options........................................... 60
Movie Live View 63
Indices ................................................................................................. 67
The Live View Display: Movie Live View ................................. 68
The Information Display: Movie Live View............................. 70
Image Area ........................................................................................ 71
Movie Settings ................................................................................. 74
Viewing Movies .................................................................................... 77
Editing Movies ...................................................................................... 79
Trimming Movies ............................................................................ 79
Saving Selected Frames................................................................ 83
Image Recording Options 85
Image Area............................................................................................. 85
Image Quality........................................................................................ 90
Image Size .............................................................................................. 93
Using Two Memory Cards ................................................................ 95
vi
Focus 97
Autofocus ............................................................................................... 97
Autofocus Mode ..............................................................................97
AF-Area Mode................................................................................ 100
Focus Point Selection.................................................................. 103
Focus Lock....................................................................................... 105
Manual Focus......................................................................................108
Release Mode 111
Choosing a Release Mode ..............................................................111
Continuous Release Modes ...................................................... 112
Self-Timer Mode.................................................................................114
Mirror up Mode ..................................................................................116
ISO Sensitivity 117
Manual Adjustment ..........................................................................117
Auto ISO Sensitivity Control ..........................................................119
Exposure 123
Metering ...............................................................................................123
Exposure Mode...................................................................................125
e: Programmed Auto ..................................................................126
f: Shutter-Priority Auto .............................................................. 127
g: Aperture-Priority Auto ........................................................... 128
h: Manual......................................................................................... 129
Long Time-Exposures.......................................................................131
Shutter-Speed and Aperture Lock...............................................133
Autoexposure (AE) Lock..................................................................135
Exposure Compensation.................................................................137
Bracketing ............................................................................................139
vii
White Balance 153
White Balance Options ....................................................................153
Fine-Tuning White Balance............................................................156
Choosing a Color Temperature ....................................................160
Preset Manual .....................................................................................163
Image Enhancement 173
Picture Controls..................................................................................173
Selecting a Picture Control........................................................173
Modifying Existing Picture Controls.......................................175
Creating Custom Picture Controls..........................................179
Sharing Custom Picture Controls............................................182
Preserving Detail in Highlights and Shadows.........................184
Active D-Lighting..........................................................................184
High Dynamic Range (HDR) ......................................................186
Flash Photography 191
Using a Flash .......................................................................................191
The Nikon Creative Lighting System (CLS) ..........................192
i-TTL Flash Control........................................................................198
Flash Modes.........................................................................................199
Flash Compensation.........................................................................202
FV Lock ..................................................................................................204
Other Shooting Options 207
Two-Button Reset: Restoring Default Settings .......................207
Multiple Exposure .............................................................................210
Interval Timer Photography ..........................................................216
Time-Lapse Photography ...............................................................223
Non-CPU Lenses.................................................................................228
Using a GPS Unit ................................................................................231
viii
More About Playback 235
Viewing Images..................................................................................235
Full-Frame Playback .................................................................... 235
Thumbnail Playback .................................................................... 235
Playback Controls ........................................................................ 236
Photo Information.............................................................................238
Taking a Closer Look: Playback Zoom........................................247
Protecting Photographs from Deletion.....................................249
Deleting Photographs .....................................................................251
Full-Frame and Thumbnail Playback..................................... 251
The Playback Menu...................................................................... 253
Voice Memos 255
Recording Voice Memos .................................................................255
Playing Voice Memos.......................................................................260
Connections 263
Connecting to a Computer ............................................................263
Before Connecting the Camera............................................... 263
Direct USB Connection............................................................... 267
Ethernet and Wireless Networks............................................. 269
Printing Photographs.......................................................................271
Connecting the Printer............................................................... 272
Printing Pictures One at a Time............................................... 273
Printing Multiple Pictures.......................................................... 275
Creating a DPOF Print Order: Print Set .................................277
Viewing Photographs on TV..........................................................280
HDMI Options ................................................................................ 281
ix
Menu Guide 283
DThe Playback Menu: Managing Images ..............................283
Playback Folder.........................................................................284
Hide Image..................................................................................284
Playback Display Options......................................................285
Copy Image(s)............................................................................286
Image Review.............................................................................289
After Delete ................................................................................290
Rotate Tall ...................................................................................290
Slide Show...................................................................................291
CThe Shooting Menu: Shooting Options ..............................293
Shooting Menu Bank...............................................................294
Extended Menu Banks............................................................295
Storage Folder...........................................................................296
File Naming.................................................................................298
Color Space.................................................................................299
Vignette Control .......................................................................300
Auto Distortion Control .........................................................301
Long Exposure NR (Long Exposure Noise Reduction)
......302
High ISO NR ................................................................................302
ACustom Settings: Fine-Tuning Camera Settings...............303
Custom Settings Bank.............................................................305
a: Autofocus ....................................................................................307
a1: AF-C Priority Selection.....................................................307
a2: AF-S Priority Selection .....................................................308
a3: Focus Tracking with Lock-On........................................309
a4: AF Activation.......................................................................309
a5: Focus Point Illumination .................................................310
a6: Focus Point Wrap-Around..............................................310
a7: Number of Focus Points..................................................311
a8: Assign AF-ON Button .......................................................311
a9: Assign AF-ON Button (Vert.) ..........................................312
a10: Store Points by Orientation.........................................312
b: Metering/Exposure..................................................................313
b1: ISO Sensitivity Step Value ..............................................313
b2: EV Steps for Exposure Cntrl ...........................................313
b3: Exp./Flash Comp. Step Value ........................................313
x
b4: Easy Exposure Compensation...................................... 314
b5: Center-Weighted Area.................................................... 315
b6: Fine-Tune Optimal Exposure........................................ 315
c: Timers/AE Lock.......................................................................... 316
c1: Shutter-Release Button AE-L......................................... 316
c2: Standby Timer .................................................................... 316
c3: Self-Timer ............................................................................. 317
c4: Monitor off Delay ..............................................................317
d: Shooting/Display ..................................................................... 318
d1: Beep....................................................................................... 318
d2: Shooting Speed................................................................. 318
d3: Max. Continuous Release............................................... 319
d4: Exposure Delay Mode ..................................................... 319
d5: File Number Sequence ...................................................320
d6: Viewfinder Grid Display.................................................. 321
d7: Control Panel/Viewfinder .............................................. 321
d8: Screen Tips .......................................................................... 321
d9: Information Display ......................................................... 322
d10: LCD Illumination............................................................. 322
e: Bracketing/Flash....................................................................... 323
e1: Flash Sync Speed............................................................... 323
e2: Flash Shutter Speed ......................................................... 324
e3: Optional Flash .................................................................... 324
e4: Exposure Comp. for Flash .............................................. 325
e5: Modeling Flash................................................................... 325
e6: Auto Bracketing Set ......................................................... 325
e7: Auto Bracketing (Mode M)............................................. 326
e8: Bracketing Order ............................................................... 326
f: Controls ........................................................................................ 327
f1: Multi Selector Center Button ......................................... 327
f2: Multi Selector....................................................................... 328
f3: Assign Fn Button................................................................ 328
f4: Assign Preview Button ..................................................... 333
f5: Assign Sub-selector........................................................... 333
f6: Assign Sub-selector Center ............................................ 333
f7: Assign Fn Button (Vert.)................................................... 334
f8: Shutter Spd & Aperture Lock ......................................... 334
f9: Assign BKT Button.............................................................. 335
f10: Customize Command Dials.......................................... 336
xi
f11: Release Button to Use Dial............................................337
f12: Slot Empty Release Lock................................................338
f13: Reverse Indicators............................................................338
f14: Assign Multi Selector (Vert.).........................................338
f15: Playback Zoom .................................................................339
f16: Assign Movie Record Button........................................339
g: Movie ............................................................................................340
g1: Assign Fn Button ...............................................................340
g2: Assign Preview Button ....................................................341
g3: Assign Sub-selector Center ...........................................342
g4: Assign Shutter Button .....................................................343
BThe Setup Menu: Camera Setup...............................................344
Format Memory Card..............................................................345
Monitor Brightness ..................................................................345
Image Dust Off Ref Photo......................................................346
Flicker Reduction......................................................................348
Time Zone and Date................................................................348
Language.....................................................................................349
Auto Image Rotation...............................................................350
Battery Info .................................................................................351
Image Comment.......................................................................352
Copyright Information............................................................353
IPTC................................................................................................354
Save/Load Settings..................................................................356
Virtual Horizon...........................................................................358
AF Fine-Tune ..............................................................................359
Firmware Version......................................................................360
NThe Retouch Menu: Creating Retouched Copies .............361
D-Lighting...................................................................................364
Red-Eye Correction..................................................................365
Trim................................................................................................366
Monochrome .............................................................................367
Filter Effects ................................................................................367
Color Balance .............................................................................368
Image Overlay............................................................................369
NEF (RAW) Processing.............................................................372
Resize ............................................................................................374
Straighten....................................................................................376
xii
Distortion Control.................................................................... 377
Perspective Control................................................................. 378
Side-by-Side Comparison .....................................................378
OMy Menu/mRecent Settings....................................................380
Technical Notes 385
Compatible Lenses............................................................................385
Other Accessories..............................................................................391
Attaching a Power Connector and AC Adapter................. 396
Caring for the Camera......................................................................398
Storage ............................................................................................. 398
Cleaning........................................................................................... 398
The Low-Pass Filter ...................................................................... 399
“Clean Now”............................................................................... 399
“Clean at Startup/Shutdown”.............................................. 400
Manual Cleaning ...................................................................... 402
Replacing the Clock Battery...................................................... 406
Caring for the Camera and Battery: Cautions..........................408
Defaults .................................................................................................412
Exposure Program.............................................................................418
Troubleshooting ................................................................................419
Error Messages....................................................................................424
Specifications......................................................................................430
Calibrating Batteries.................................................................... 440
Approved Memory Cards ...............................................................442
Memory Card Capacity ....................................................................444
Battery Life ...........................................................................................447
Index.......................................................................................................449
xiii
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to
others, read the following safety precautions in their entirety before using
this equipment. Keep these safety instructions where all those who use
the product will read them.
The consequences that could result from failure to observe the
precautions listed in this section are indicated by the following symbol:
❚❚ WARNINGS
AKeep the sun out of the frame
Keep the sun well out of the frame
when shooting backlit subjects.
Sunlight focused into the camera
when the sun is in or close to the
frame could cause a fire.
ADo not look at the sun through the
viewfinder
Viewing the sun or other strong
light source through the
viewfinder could cause
permanent visual impairment.
AUsing the viewfinder diopter adjustment
control
When operating the viewfinder
diopter adjustment control with
your eye to the viewfinder, care
should be taken not to put your
finger in your eye accidentally.
ATurn off immediately in the event of
malfunction
Should you notice smoke or an
unusual smell coming from the
equipment or AC adapter
(available separately), unplug the
AC adapter and remove the
battery immediately, taking care
to avoid burns. Continued
operation could result in injury.
After removing the battery, take
the equipment to a Nikon-
authorized service center for
inspection.
ADo not disassemble
Touching the product’s internal
parts could result in injury. In the
event of malfunction, the product
should be repaired only by a
qualified technician. Should the
product break open as the result
of a fall or other accident, remove
the battery and/or AC adapter
and then take the product to a
Nikon-authorized service center
for inspection.
This icon marks warnings. To prevent possible injury, read all
warnings before using this Nikon product.
A
xiv
ADo not use in the presence of flammable
gas
Do not use electronic equipment
in the presence of flammable gas,
as this could result in explosion or
fire.
AKeep out of reach of children
Failure to observe this precaution
could result in injury.
In addition,
note that small parts constitute a
chocking hazard.
Should a child
swallow any part of this
equipment, consult a physician
immediately.
ADo not place the strap around the neck of
an infant or child
Placing the camera strap around
the neck of an infant or child
could result in strangulation.
ADo not remain in contact with the
camera, battery, or charger for extended
periods while the devices are on or in use
Parts of the device become hot.
Leaving the device in direct
contact with the skin for extended
periods may result in low-
temperature burns.
AObserve proper precautions when
handling batteries
Batteries may leak or explode if
improperly handled. Observe the
following precautions when
handling batteries for use in this
product:
• Use only batteries approved for
use in this equipment.
• Use only CR1616 lithium batteries
to replace the clock battery. Using
another type of battery could
cause an explosion. Dispose of
used batteries as directed.
• Do not short or disassemble the
battery.
• Be sure the product is off before
replacing the battery. If you are
using an AC adapter, be sure it is
unplugged.
• Do not attempt to insert the
battery upside down or
backwards.
• Do not expose the battery to
flame or to excessive heat.
• Do not immerse in or expose to
water.
• Replace the terminal cover when
transporting the battery. Do not
transport or store the battery with
metal objects such as necklaces or
hairpins.
• Batteries are prone to leakage
when fully discharged. To avoid
damage to the product, be sure to
remove the battery when no
charge remains.
• When the battery is not in use,
attach the terminal cover and
store in a cool, dry place.
• The battery may be hot
immediately after use or when the
product has been used on battery
power for an extended period.
Before removing the battery turn
the camera off and allow the
battery to cool.
• Discontinue use immediately
should you notice any changes in
the battery, such as discoloration
or deformation.
xv
AObserve proper precautions when
handling the charger
• Keep dry. Failure to observe this
precaution could result in fire or
electric shock.
• Dust on or near the metal parts of
the plug should be removed with
a dry cloth. Continued use could
result in fire.
• Do not handle the power cable or
go near the charger during
thunderstorms. Failure to observe
this precaution could result in
electric shock.
• Do not damage, modify, or
forcibly tug or bend the power
cable. Do not place it under
heavy objects or expose it to heat
or flame. Should the insulation be
damaged and the wires become
exposed, take the power cable to
a Nikon-authorized service
representative for inspection.
Failure to observe this precaution
could result in fire or electric
shock.
• Do not handle the plug or charger
with wet hands. Failure to
observe this precaution could
result in electric shock.
• Do not use with travel converters
or adapters designed to convert
from one voltage to another or
with DC-to-AC inverters.
Failure
to observe this precaution could
damage the product or cause
overheating or fire.
AUse appropriate cables
When connecting cables to the
input and output jacks, use only
the cables provided or sold by
Nikon for the purpose to maintain
compliance with product
regulations.
ACD-ROMs
CD-ROMs containing software or
manuals should not be played
back on audio CD equipment.
Playing CD-ROMs on an audio CD
player could cause hearing loss or
damage the equipment.
ADo not aim a flash at the operator of a
motor vehicle
Failure to observe this precaution
could result in accidents.
AObserve caution when using the flash
• Using optional flash units in close
contact with the skin or other
objects could cause burns.
• Using optional flash units close to
the subject’s eyes could cause
temporary visual impairment.
Particular care should be
observed when photographing
infants, when the flash should be
no less than one meter (39 in.)
from the subject.
AAvoid contact with liquid crystal
Should the monitor break, care
should be taken to avoid injury
due to broken glass and to
prevent the liquid crystal from the
monitor touching the skin or
entering the eyes or mouth.
xvi
Notices
• No part of the manuals included with this
product may be reproduced, transmitted,
transcribed, stored in a retrieval system,
or translated into any language in any
form, by any means, without Nikon’s prior
written permission.
• Nikon reserves the right to change the
specifications of the hardware and
software described in these manuals at
any time and without prior notice.
• Nikon will not be held liable for any
damages resulting from the use of this
product.
• While every effort has been made to
ensure that the information in these
manuals is accurate and complete, we
would appreciate it were you to bring
any errors or omissions to the attention
of the Nikon representative in your area
(address provided separately).
Notices for Customers in Canada
CAUTION
This Class B digital apparatus complies
with Canadian ICES-003.
ATTENTION
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du
Canada.
Notices for Customers in Europe
This symbol indicates that
electrical and electronic
equipment is to be collected
separately.
The following apply only to
users in European countries:
• This product is designated for separate
collection at an appropriate collection
point. Do not dispose of as household
waste.
• Separate collection and recycling
helps conserve natural resources and
prevent negative consequences for
human health and the environment
that might result from incorrect
disposal.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
This symbol on the battery
indicates that the battery is
to be collected separately.
The following apply only to
users in European countries:
• All batteries, whether marked with this
symbol or not, are designated for
separate collection at an appropriate
collection point.
Do not dispose of as
household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
xvii
Notices for Customers in the U.S.A.
Federal Communications Commission (FCC) Radio Frequency Interference Statement
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation.
If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced
radio/television technician for help.
CAUTIONS
Modifications
The FCC requires the user be notified that
any changes or modifications made to this
device that are not expressly approved by
Nikon Corporation may void the user’s
authority to operate the equipment.
The accessory power cord must be used
For USA only: Over AC 125 V
Use a power cord over AWG 18 in size
suited to the voltage in use with plugs
rated for AC 250 V 15 A (NEMA 6P-15)
and a minimum of SVT type cord for
insulation.
Power Supply Cord
Use a UL Listed, 1.8 to 3 m (6 to 10 ft),
SPT-2, AWG no. 18 power supply cord
rated for 125 V 7 A, with a non-polarized
NEMA 1-15P plug rated for 125 V 15 A.
The Battery Charger
IMPORTANT SAFETY INSTRUCTIONS—SAVE THESE
INSTRUCTIONS
DANGER—TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS
For connection to a supply not in the U.S.A., use an attachment plug
adapter of the proper configuration for the power outlet if needed. This
power unit is intended to be correctly oriented in a vertical or floor
mount position.
xviii
Notice for Customers in the State of California
WARNING: Handling the cord on this product
may expose you to lead, a chemical known
to the State of California to cause birth
defects or other reproductive harm.
Wash
hands after handling.
Nikon Inc., 1300 Walt Whitman Road,
Melville, New York 11747-3064, U.S.A.
Tel.: 631-547-4200
Disposing of Data Storage Devices
Please note that deleting images or formatting memory cards or other data storage
devices does not completely erase the original image data. Deleted files can
sometimes be recovered from discarded storage devices using commercially
available software, potentially resulting in the malicious use of personal image
data. Ensuring the privacy of such data is the user’s responsibility.
Before discarding a data storage device or transferring ownership to another
person, erase all data using commercial deletion software, or format the device and
then completely refill it with images containing no private information (for
example, pictures of empty sky). Be sure to also replace any pictures selected for
preset manual (0168). Care should be taken to avoid injury when physically
destroying data storage devices.
xix
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that has been digitally copied or
reproduced by means of a scanner, digital camera, or other device may be
punishable by law.
• Items prohibited by law from being copied or
reproduced
Do not copy or reproduce paper
money, coins, securities, government
bonds, or local government bonds,
even if such copies or reproductions
are stamped “Sample.”
The copying or reproduction of paper
money, coins, or securities which are
circulated in a foreign country is
prohibited.
Unless the prior permission of the
government has been obtained, the
copying or reproduction of unused
postage stamps or post cards issued by
the government is prohibited.
The copying or reproduction of stamps
issued by the government and of
certified documents stipulated by law
is prohibited.
• Cautions on certain copies and reproductions
The government has issued cautions
on copies or reproductions of
securities issued by private companies
(shares, bills, checks, gift certificates,
etc.), commuter passes, or coupon
tickets, except when a minimum of
necessary copies are to be provided for
business use by a company. Also, do
not copy or reproduce passports
issued by the government, licenses
issued by public agencies and private
groups, ID cards, and tickets, such as
passes and meal coupons.
• Comply with copyright notices
The copying or reproduction of
copyrighted creative works such as
books, music, paintings, woodcuts,
prints, maps, drawings, movies, and
photographs is governed by national
and international copyright laws. Do
not use this product for the purpose of
making illegal copies or to infringe
copyright laws.
Use Only Nikon Brand Electronic Accessories
Nikon cameras are designed to the highest standards and include complex
electronic circuitry.
Only Nikon brand electronic accessories (including chargers,
batteries, AC adapters, and flash accessories) certified by Nikon specifically for use
with this Nikon digital camera are engineered and proven to operate within the
operational and safety requirements of this electronic circuitry.
The use of non-Nikon electronic accessories could damage the
camera and may void your Nikon warranty.
The use of third-party
rechargeable Li-ion batteries not bearing the Nikon holographic seal
shown at right could interfere with normal operation of the camera
or result in the batteries overheating, igniting, rupturing, or leaking.
For more information about Nikon brand accessories, contact a local authorized
Nikon dealer.
xx
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR
ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
http://www.mpegla.com
DUse Only Nikon Brand Accessories
Only Nikon brand accessories certified by Nikon specifically for use with
your Nikon digital camera are engineered and proven to operate within
its operational and safety requirements.
THE USE OF NON-NIKON
ACCESSORIES COULD DAMAGE YOUR CAMERA AND MAY VOID YOUR NIKON
WARRANTY.
DServicing the Camera and Accessories
The camera is a precision device and requires regular servicing.
Nikon
recommends that the camera be inspected by the original retailer or a
Nikon-authorized service representative once every one to two years,
and that it be serviced once every three to five years (note that fees
apply to these services).
Frequent inspection and servicing are
particularly recommended if the camera is used professionally.
Any
accessories regularly used with the camera, such as lenses or optional
flash units, should be included when the camera is inspected or
serviced.
ABefore Taking Important Pictures
Before taking pictures on important occasions (such as at weddings or
before taking the camera on a trip), take a test shot to ensure that the
camera is functioning normally.
Nikon will not be held liable for
damages or lost profits that may result from product malfunction.
xxi
ALife-Long Learning
As part of Nikon’s “Life-Long Learning” commitment to ongoing
product support and education, continually-updated information is
available on-line at the following sites:
•For users in the U.S.A.: http://www.nikonusa.com/
•For users in Europe and Africa: http://www.europe-nikon.com/support/
•For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information,
tips, answers to frequently-asked questions (FAQs), and general advice
on digital imaging and photography.
Additional information may be
available from the Nikon representative in your area.
See the following
URL for contact information: http://imaging.nikon.com/
xxii
Quick Start Guide
Follow these steps for a quick start with the D4.
1Attach the camera strap.
Attach the strap securely to the camera eyelets.
2Charge (023) and insert (025) the battery.
Attach the battery-chamber cover before inserting the
battery.
3Attach a lens (028).
xxiii
4Insert a memory card (033).
5Turn the camera on (040).
6Select autofocus (097).
Rotate the focus-mode selector
to AF (autofocus).
7Focus and shoot (043, 44).
Press the shutter-release
button halfway to focus, then
press the shutter-release
button the rest of the way
down to take the photograph.
8View the
photograph
(046).
ASee Also
For information on choosing a language and setting the time and
date, see page 30.
See page 38 for information on adjusting
viewfinder focus.
Back
Focus-mode selector
Focus indicator
K button
xxiv
X
1
X
Introduction
Be sure all items listed here were included with your camera.
Memory cards are sold separately.
•AN-DC7 strap (0xxii)
•Warranty
•User’s Manual (this guide)
• Quick Guide
•Network Guide
• ViewNX 2 installer CD (0263)
Package Contents
•D4 digital
camera (02)
• BF-1B body cap (028,
394)
• BS-2 accessory shoe
cover (
0
17
,
191)
• EN-EL18 rechargeable Li-ion
battery with terminal cover
(023, 25)
• UC-E15 USB cable
(0267, 272)
•USB cable clip
(0267)
• MH-26 battery charger with
power cable and two contact
protectors (023, 440)
• UF-2 connector
cover for stereo
mini plug cable
(0395)
2
X
Getting to Know the Camera
Take a few moments to familiarize yourself with camera controls
and displays.
You may find it helpful to bookmark this section and
refer to it as you read through the rest of the manual.
Camera Body
1D button
Bracketing .......141, 145, 149, 335
2Release mode dial
lock release ....................................111
3Eyelet for camera strap ............... xxii
4M button
Flash mode.................................200
Flash compensation.................202
5Y button
Metering.....................................124
6Release mode dial........................111
7Power switch .............................10, 40
8Shutter-release button ...........43, 44
9Movie-record button............ 65, 339
10 E button
Exposure compensation.........137
11 I/Q button
Exposure mode .........................125
Formatting memory cards ....... 36
12 Eyelet for camera strap ............... xxii
13 Top control panel ............................. 7
14 Focal plane mark (E).................109
15 Diopter adjustment control.........38
16 Accessory shoe
(for optional flash unit)........ 17, 191
17 Accessory shoe cover
.......................................... 17, 191, 410
3
X
1Mirror..................................... 116, 402
2Self-timer lamp ............................ 115
3Microphone (for movies)
................................................65, 69, 75
4Flash sync terminal cover .......... 191
5Ten-pin remote terminal
cover ...................................... 231, 394
6Flash sync terminal...................... 191
7Ten-pin remote terminal... 231, 394
8USB connector cover.......... 267, 272
9Peripheral connector cover....... 391
10 Audio connector cover..................69
11 HDMI/Ethernet connector
cover ...................................... 269, 280
12 Peripheral connector .................. 391
13 USB connector..................... 267, 272
14 Headphone connector .........69, 261
15 Connector for external
microphone......................................69
16 HDMI mini-pin connector.......... 280
17 Ethernet connector ..................... 269
18 Lens release button........................29
19 AF-mode button ...... 52, 54, 98, 101
20 Battery-chamber cover latch .......25
21 Battery-chamber cover .................25
22 Focus-mode selector .....52, 97, 108
23 Meter coupling lever................... 433
24 Body cap ..................................28, 394
4
X
Camera Body (Continued)
1Pv button
Using the Pv button
............................. 67, 125, 333, 341
2Sub-command dial ......................336
3Fn button
Using the Fn button
............................. 89, 205, 328, 340
4Sub-command dial for
vertical shooting...........................336
5Shutter-release button for
vertical shooting
6Vertical shooting shutter-release
button lock....................................... 42
7Fn button (vertical)
Using the
Fn
button (vertical)
....334
8CPU contacts
9Mounting index .............................. 29
10 Lens mount............................. 29, 109
11 Tripod socket
DThe Microphone and Speaker
Do not place the microphone or speaker in close proximity to magnetic
devices.
Failure to observe this precaution could affect the data
recorded on the magnetic devices.
5
X
1Viewfinder eyepiece .............39, 114
2Eyepiece shutter lever ..........39, 114
3O/Q button
Deletion ...............................47, 251
Formatting memory cards........36
4K button
Playback...............................46, 235
5Monitor ..............46, 49, 63, 235, 345
6G button
Menus...................................19, 283
7L (Z/Q) button
Protection.................................. 249
Picture Controls........................ 173
Help................................................22
8X button
Playback zoom in..................... 247
9W button
Thumbnails ............................... 235
Playback zoom out.................. 247
10 J (OK) button ........................20, 236
11 R (info) button........................ 13, 16
12 Rear control panel ...................9, 321
13 S button
ISO sensitivity ........................... 117
Auto ISO sensitivity control... 119
Two-button reset ..................... 207
14 T button
Image quality and size........91, 93
15 U button
White balance......... 153, 159, 162
Two-button reset ..................... 207
16 H button
Using the microphone
.................................... 256, 257, 258
6
X
Camera Body (Continued)
1Viewfinder........................................ 38
2Sub-selector
......................104, 105, 135, 333, 342
3B button
AF-ON................................... 99, 311
4Main command dial.....................336
5Multi selector ...................20, 45, 237
6Card slot cover release button
(under cover)................................... 33
7Memory card slot cover ..........33, 35
8C button
Using the AF-ON button for
vertical shooting.......................312
9Main command dial (vertical) ...336
Speaker .................................... 77, 261
10 Focus selector lock.......................103
11 Microphone
(for voice memos) ........................255
12 Live view selector.................... 49, 63
13 a button
Live view................................ 49, 63
14 Multi selector (vertical) ...............338
15 Memory card access lamp..... 34, 44
16 Ambient brightness sensor for
automatic monitor brightness
control...................................... 57, 345
7
X
The Top Control Panel
1
2
3
4
5
6
8
713
12
11
10
9
1Shutter speed...........................127, 129
AF-area mode ............................ 98, 102
Exposure compensation value .....137
Flash compensation value.............202
Number of shots in
exposure and flash bracketing
sequence............................................141
Number of shots in
WB bracketing sequence ...............145
HDR exposure differential..............190
Number of exposures (multiple
exposure) ...........................................212
Number of intervals for
interval timer photography...........220
Focal length (non-CPU lenses) .....230
ISO sensitivity....................................117
2Flexible program indicator ............126
3Exposure mode.................................125
4Shooting menu bank ......................294
5Custom settings bank.....................305
6XQD card indicator.......................35, 36
7CompactFlash card indicator ....35, 36
8Number of exposures remaining
........................................................41, 444
Number of shots remaining before
memory buffer fills................. 113, 444
Capture mode indicator................. 265
9Aperture stop indicator......... 128, 388
10
Aperture (f-number)
............... 128, 129
Aperture (number of stops)
... 128, 388
Bracketing increment ............ 142, 146
Number of shots in ADL bracketing
sequence............................................ 149
Number of shots per interval........ 220
Maximum aperture
(non-CPU lenses) ............................. 230
PC mode indicator........................... 269
11 Battery indicator .................................40
12 Frame count.........................................45
Preset white balance
recording indicator.......................... 165
Active D-Lighting amount.... 150, 332
Manual lens number....................... 230
Time-lapse recording indicator.... 226
13 “K” (appears when memory remains
for over 1000 exposures) ..................41
8
X
14
15
16
18
19
17
21
20
22
31
30
27
28
25
26
29
23
24
14 Clock battery indicator............ 32, 406
15 FV lock indicator...............................205
16 Shutter-speed lock icon .................133
17 Flash sync indicator.........................323
18 Flash mode........................................199
19 Metering.............................................124
20 AF-area mode indicator.........100, 102
Auto-area AF indicator ..........101, 102
3D-tracking indicator.............100, 102
21 Autofocus mode................................. 97
22 Interval timer indicator...................220
Time-lapse on indicator .................226
23 Multiple exposure indicator ..........211
24 Aperture lock icon ...........................134
HDR (series) indicator .....................190
Multiple exposure (series)
indicator.............................................212
25 GPS connection indicator ..............232
26 HDR indicator.................................... 187
27 “Beep” indicator ...............................318
28 Exposure compensation
indicator.............................................137
29 Flash compensation indicator ......202
30 Exposure and flash
bracketing indicator........................ 141
WB bracketing indicator ................ 145
ADL bracketing indicator............... 149
Active D-Lighting indicator
.... 150, 332
31 Exposure indicator .......................... 130
Exposure compensation
display ................................................ 137
Bracketing progress indicator:
Exposure and flash bracketing
..... 141
WB bracketing............................... 145
ADL bracketing.............................. 149
PC connection indicator ................ 265
9
X
The Rear Control Panel
2
1
3
4
5
7
6
8
9
10
11
1“Remaining” indicator ....................321
2Image size............................................ 93
3ISO sensitivity indicator..................117
Auto ISO sensitivity
indicator .............................................121
4ISO sensitivity....................................117
ISO sensitivity (high/low gain)......118
Number of exposures remaining
....321
Length of voice memo....................258
White balance fine-tuning.............159
White balance preset number......164
Color temperature ..................153, 160
PC mode indicator ...........................265
5“K” (appears when memory remains
for over 1000 exposures).................. 41
Color temperature indicator .........162
6Image quality (JPEG images) ...........90
7Voice memo recording
indicator (shooting mode) ............ 256
8Voice memo status
indicator.................................... 258, 259
9Voice memo recording
mode................................................... 256
10 White balance................................... 153
White balance fine-tuning
indicator............................................. 159
White balance preset protection
indicator............................................. 171
11 Secondary slot function....................95
Image quality.......................................90
10
X
ALCD Illuminators
Rotating the power switch toward
D
activates the standby timer, control
panel backlights (LCD illuminators),
and button backlights (0
322
),
making it easier to use the camera in
the dark. After the power switch is
released, the backlights will remain
lit for six seconds while the standby
timer is active or until the shutter is released or the power switch is
rotated toward
D
again.
Power switch
11
X
The Viewfinder Display
234
5
6
7
1
8
22 23 24 25
9101112 13 1415 16 17 18 19 20 21
1Framing grid (displayed when On
is selected for Custom Setting d6)
.......................................................... 321
212-mm reference circle for center-
weighted metering ..................... 123
3AF area brackets..............................38
4Focus points..........43, 103, 310, 311
Spot metering targets ................ 123
AF-area mode indicator ............. 101
Roll indicator 1 ............................. 331
5Exposure indicator....................... 130
Exposure compensation display
.......................................................... 137
Bracketing progress indicator:
Exposure and flash
bracketing.................................. 141
WB bracketing .......................... 145
ADL bracketing......................... 149
Pitch indicator 2 ........................... 331
6Exposure compensation
indicator......................................... 137
Flash compensation indicator
... 202
12
X
1 Functions as a pitch indicator when camera is rotated to take pictures in “tall”
(portrait) orientation.
2 Functions as a roll indicator when camera is rotated to take pictures in “tall” (portrait)
orientation.
3 Displayed when an optional flash unit is attached (0192). The flash-ready indicator
lights when the flash is charged.
7Bracketing indicator:
Exposure and flash
bracketing ..................................139
WB bracketing...........................145
ADL bracketing .........................149
8Focus indicator....................... 43, 109
9Metering.........................................123
10 Autoexposure (AE) lock ..............135
11 Exposure mode.............................125
12 Shutter speed lock icon ..............133
13 Shutter speed.......................127, 129
Autofocus mode ............................. 97
14 Aperture lock icon........................134
15 Aperture (f-number)...........128, 129
Aperture
(number of stops)................128, 388
16 ISO sensitivity indicator ..............117
Auto ISO sensitivity indicator
.....120
17 ISO sensitivity................................117
Active D-Lighting amount .........332
AF-area mode.......................101, 102
18 Network display............................269
19 Frame count...................................321
Number of exposures
remaining....................... 41, 321, 444
Number of shots remaining before
memory buffer fills ...... 43, 113, 444
Preset white balance
recording indicator ......................165
Exposure compensation value
.....137
Flash compensation value .........202
PC mode indicator........................265
20 “K” (appears when memory
remains for over 1000
exposures)........................................ 41
21 Flash-ready indicator 3
........................................195, 205, 434
22 FV lock indicator ...........................205
23 Flash sync indicator .....................323
24 Aperture stop indicator .....128, 388
25 Low battery warning ..................... 40
DNo Battery
When the battery is totally exhausted or no battery is inserted, the
display in the viewfinder will dim.
This is normal and does not indicate a
malfunction.
The viewfinder display will return to normal when a fully-
charged battery is inserted.
DThe Control Panel and Viewfinder Displays
The brightness of the control panel and viewfinder displays varies with
temperature, and the response times of the displays may drop at low
temperatures.
This is normal and does not indicate a malfunction.
13
X
The Information Display
Shooting information, including shutter
speed, aperture, frame count, number of
exposures remaining, and AF-area mode, is
displayed in the monitor when the R button
is pressed.
R button
10
20
21
17
19
123 4 5 6
8
16 15 14 13 12
111111
7
9
18
1Exposure mode.................................125
2Flexible program indicator ............126
3Shutter-speed lock icon .................133
4Shutter speed...........................127, 129
Exposure compensation value .....137
Flash compensation value.............202
Number of shots in exposure and
flash bracketing sequence.............141
Number of shots in WB bracketing
sequence............................................145
Number of exposures (multiple
exposure) ...........................................212
Focal length (non-CPU lenses) .....230
5Multiple exposure indicator..........211
6Aperture (f-number) .............. 128, 129
Aperture (number of stops)
.... 128, 388
Bracketing increment ............ 142, 146
Number of shots in ADL bracketing
sequence............................................ 149
Maximum aperture
(non-CPU lenses) ............................. 230
7Exposure indicator........................... 130
Exposure compensation display
..... 137
Bracketing progress indicator:
Exposure and flash bracketing
... 141
WB bracketing............................... 145
ADL bracketing.............................. 149
8“Beep” indicator............................... 318
14
X
9Position of current frame in
bracketing sequence .............150, 151
ADL bracketing amount ................150
10 “K” (appears when memory
remains for over 1000
exposures) ........................................... 41
11 Frame count ....................................... 45
Manual lens number.......................230
12 Sub-selector center
assignment........................................342
13 Pv button assignment ....................333
14 Active D-Lighting indicator...........185
15 High ISO noise reduction
indicator.............................................302
16 Shooting menu bank ......................294
17 Number of exposures
remaining ...................................41, 444
18 Exposure and flash
bracketing indicator........................ 141
WB bracketing indicator ................ 145
ADL bracketing indicator............... 149
19 Auto-area AF indicator.......... 101, 102
Focus points indicator.................... 103
AF-area mode indicator ........ 100, 101
3D-tracking indicator ............ 100, 102
20 Flash mode........................................ 199
21 Flash sync indicator......................... 323
ATurning the Monitor Off
To clear shooting information from the monitor, press the
R
button twice
more or press the shutter-release button halfway. The monitor will turn off
automatically if no operations are performed for about 10 seconds.
ASee Also
For information on choosing how long the monitor stays on, see
Custom Setting c4 (Monitor off delay, 0317). For information on
changing the color of the lettering in the information display, see
Custom Setting d9 (Information display, 0322).
15
X
The Information Display (Continued)
32
33
31
36
37
35
34
43
46
44
22
42 41 40 39 38
23 24 26
25
30
29
27 28
45
22 Release mode indicator..................111
Continuous shooting speed..........112
23 FV lock indicator...............................205
24 Clock battery indicator ............ 32, 406
25 Interval timer indicator...................220
Time-lapse indicator .......................226
26 GPS connection indicator ..............232
27 Aperture stop indicator.........128, 388
28 Aperture lock icon ...........................134
HDR (series) indicator .....................190
Multiple exposure (series)
indicator .............................................212
29 Image comment indicator.............352
30 Copyright information
indicator .............................................353
31 IPTC indicator....................................354
32 Network display ...............................269
33 Exposure compensation
indicator .............................................137
34 Flash compensation indicator...... 202
35 Battery indicator .................................40
36 HDR indicator ................................... 187
HDR exposure differential ............. 190
37 Picture Control indicator................ 174
38 Function assigned to Fn button
(vert.) .................................................. 334
39 Fn button assignment..................... 328
40 D button assignment................. 335
41 Long exposure noise reduction
indicator............................................. 302
42 Custom settings bank..................... 305
43 Autofocus mode indicator.........97, 98
44 Vignette control indicator ............. 300
45 Image area indicator..........................85
46 Metering ............................................ 123
16
X
❚❚ Changing Settings in the Information Display
To change settings for the items listed below,
press the R button in the information
display.
Highlight items using the multi
selector and press J to view options for the
highlighted item.
R button
1Shooting menu bank...................294
2High ISO noise reduction ...........302
3Active D-Lighting .........................184
4Pv button assignment.................333
5Sub-selector center
assignment ....................................333
6Fn button (vert.) assignment.....334
7Fn button assignment .................328
8D button assignment..............335
9Long exposure noise
reduction........................................302
10 Custom settings bank .................305
ATool Tips
A tool tip giving the name of the selected item
appears in the information display.
Tool tips can
be turned off using Custom Setting d8 (Screen
tips; 0321).
17
X
The BS-2 Accessory Shoe Cover
The supplied BS-2 accessory shoe
cover can be used to protect the
accessory shoe or to prevent light
reflected from the metal parts of
the shoe from appearing in
photographs. The BS-2 attaches to
the camera accessory shoe as shown at right.
To remove the accessory shoe
cover, hold it down with your
thumb and slide it off as shown at
right while keeping a firm grip on
the camera.
18
X
s
19
s
Tutorial
Most shooting, playback, and setup options
can be accessed from the camera menus.
To
view the menus, press the G button.
Camera Menus
G button
Choose from the following menus:
•D: Playback (0283) • B: Setup (0344)
•C: Shooting (0293) • N: Retouch (0361)
•A: Custom Settings (0303) • O/m: My Menu or Recent settings
(defaults to My Menu; 0380)
Tabs
Slider shows position in current menu.
Current settings are shown by icons.
If d icon is displayed, help for current item can be viewed by pressing
L (Z/Q) button (022).
d
Options in current menu.
Menu options
20
s
Using Camera Menus
❚❚ Menu Controls
The multi selector and J button are used to navigate the menus.
❚❚ Navigating the Menus
Follow the steps below to navigate the menus.
1Display the menus.
Press the G button to display the
menus.
2Highlight the icon for the
current menu.
Press 4 to highlight the icon
for the current menu.
Move cursor up
Cancel and return
to previous menu
Select
highlighted
item or display
sub-menu
Select
highlighted
item
Select highlighted
item
J button
Move cursor down
Multi selector
G button
21
s
3Select a menu.
Press 1 or 3 to select the desired menu.
4Position the cursor in the
selected menu.
Press 2 to position the cursor
in the selected menu.
5Highlight a menu item.
Press 1 or 3 to highlight a
menu item.
6Display options.
Press 2 to display options for
the selected menu item.
7Highlight an option.
Press 1 or 3 to highlight an
option.
22
s
8Select the highlighted item.
Press J to select the highlighted item.
To
exit without making a selection, press the
G button.
Note the following points:
• Menu items that are displayed in gray are not currently available.
• While pressing 2 or the center of the multi selector generally has
the same effect as pressing J, there are some cases in which
selection can only be made by pressing J.
• To exit the menus and return to shooting mode, press the
shutter-release button halfway (044).
Help
If a d icon is displayed at the bottom left
corner of the monitor, help can be displayed
by pressing the L (Z/Q) button.
A description of the currently
selected option or menu will
be displayed while the button
is pressed.
Press 1 or 3 to
scroll through the display.
J button
L (Z/Q) button
23
s
First Steps
Charge the Battery
The D4 is powered by an EN-EL18 rechargeable Li-ion battery
(supplied).
To maximize shooting time, charge the battery in the
supplied MH-26 battery charger before use.
About two hours and
twenty minutes are required to fully recharge the battery when no
charge remains.
1Plug the charger in.
Insert the AC adapter plug into the
battery charger and plug the power
cable into an electrical outlet.
2Remove the terminal cover.
Remove the terminal cover from the
battery.
3Remove the contact protector.
Remove the contact protector from the
charger battery chamber.
ASee Also
For information on using the MH-26 to charge two batteries, see page
441.
Terminal cover
24
s
4Charge the battery.
Insert the battery (terminals first), aligning the end of the
battery with the guide and then sliding the battery in the
direction indicated until it clicks into place.
The chamber lamp
and charge lamps will flash slowly while the battery charges:
Charging is complete when the chamber lamp stops flashing
and the charge lamps turn off.
About two hours and twenty
minutes are required to fully charge an exhausted battery;
note that the battery will not charge if its temperature is
below 0 °C (32 °F) or above 60 °C (140 °F).
5Remove the battery when charging is complete.
Remove the battery and unplug the charger.
Charge state
Chamber
lamp
Charge lamps
50% 80% 100%
Less than 50% of maximum capacity H (flashes
slowly)
H (flashes
slowly) I (off) I (off)
50–80% of maximum capacity H (flashes
slowly) K (glows) H (flashes
slowly) I (off)
More than 80% but less than 100% of
maximum capacity
H (flashes
slowly) K (glows) K (glows) H (flashes
slowly)
100% of maximum capacity K (glows) I (off) I (off) I (off)
DCalibration
See page 440 for more information on calibration.
Guide
Chamber
lamps
Charge
lamps
(green)
Contacts
25
s
Insert the Battery
1Turn the camera off.
2Remove the battery-chamber cover.
Lift the battery-chamber cover latch, turn it
to the open (
A
) position (
q
) and remove
the BL-6 battery-chamber cover (
w
).
3Attach the cover to the battery.
If the battery release is positioned so that
the arrow (4) is visible, slide the battery
release to cover the arrow.
Insert the two
projections on the battery into the
matching slots in the cover and slide the
battery release to completely reveal the
arrow.
DInserting and Removing
Batteries
Always turn the camera off
before inserting or removing
batteries.
DThe BL-6 Battery-Chamber Cover
The battery can be charged with the BL-6 attached. To prevent dust
from accumulating inside the battery chamber when the battery is not
inserted, slide the battery release in the direction indicated by the arrow
(4), remove the BL-6 from the battery, and replace it on the camera.
Other battery covers can not be used with this camera.
26
s
4Insert the battery.
Insert the battery as shown at right.
5Latch the cover.
To prevent the battery from
becoming dislodged during
operation, rotate the latch to
the closed position and fold it
down as shown at right.
Be
sure the cover is securely
latched.
ARemoving the Battery
Before removing the battery, turn the camera off,
lift the battery-chamber cover latch, and turn it
to the open (A) position.
Note that the battery
may be hot after use; observe due caution when
removing the battery.
To prevent short-circuits,
replace the terminal cover when the battery is
not in use.
DEN-EL18 Rechargeable Li-ion Batteries
The supplied EN-EL18 shares information with compatible devices,
enabling the camera to show battery charge state in six levels (040).
The Battery info option in the setup menu details battery charge,
battery life, and the number of pictures taken since the battery was last
charged (0351).
The battery can be recalibrated as necessary to
ensure that battery level continues to be reported accurately (0440).
27
s
DThe Battery and Charger
Read and follow the warnings and cautions on pages xiii–xv and 408–411
of this manual.
Do not use the battery at ambient temperatures below
0 °C/32 °F or above 40 °C/104 °F; failure to observe this precaution could
damage the battery or impair its performance.
Capacity may be
reduced and charging times increase at battery temperatures from 0 °C/
32 °F to 15 °C/59 °F and from 45 °C/113 °F to 60 °C/140 °F.
Do not short the charger terminals; failure to observe this precaution
could result in overheating and damage to the charger.
Charge indoors
at ambient temperatures of 5–35°C/41–95 °F.
Battery capacity may
temporarily drop if the battery is charged at low temperatures or used
at a temperature below the temperature at which it was charged.
If the
battery is charged at a temperature below 5 °C (41 °F), the battery life
indicator in the Battery info (0351) display may show a temporary
decrease.
The battery may be hot immediately after use.
Wait for the battery to
cool before recharging.
Use the charger with compatible batteries only.
Unplug when not in
use.
A marked drop in the time a fully charged battery retains its charge
when used at room temperature indicates that it requires replacement.
Purchase a new EN-EL18 battery.
28
s
Attach a Lens
Care should be taken to prevent dust from entering the camera
when the lens is removed.
The lens generally used in this manual
for illustrative purposes is an AF-S NIKKOR 50mm f/1.4G.
1Turn the camera off.
2Remove the rear lens cap and the camera body cap.
Focus-mode switch (029)
Mounting index
Lens cap
Focus ring (0108)
CPU contacts (0387)
29
s
3Attach the lens.
Keeping the mounting index on the lens aligned with the
mounting index on the camera body, position the lens in the
camera’s bayonet mount (q).
Being careful not to press the
lens-release button, rotate the lens counter-clockwise until it
clicks into place (w).
If the lens is equipped with an A-M or
M/A-M mode switch, select A
(autofocus) or M/A (autofocus with
manual priority).
DDetaching the Lens
Be sure the camera is off when removing or
exchanging lenses. To remove the lens, press
and hold the lens release button (q) while
turning the lens clockwise (w). After removing
the lens, replace the lens caps and camera
body cap.
DCPU Lenses with Aperture Rings
In the case of CPU lenses equipped with an aperture ring (0387), lock
aperture at the minimum setting (highest f-number).
AImage Area
The DX format image area is automatically
selected when a DX lens is attached (085).
Image area
30
s
Basic Setup
The language option in the setup menu is automatically
highlighted the first time menus are displayed. Choose a language
and set the time and date.
1Turn the camera on.
2Select Language in the
setup menu.
Press G to display the
camera menus, then select
Language in the setup menu.
For information on using
menus, see “Using Camera
Menus” (020).
3Select a language.
Press 1 or 3 to highlight
the desired language and
press J.
Power switch
G button
J button
31
s
4Select Time zone and date.
Select Time zone and date
and press 2.
5Set time zone.
Select Time zone and press 2.
Press 4 or 2 to highlight the
local time zone (the UTC field
shows the difference between
the selected time zone and
Coordinated Universal Time, or
UTC, in hours) and press J.
6Turn daylight saving time
on or off.
Select Daylight saving time
and press 2.
Daylight saving
time is off by default; if daylight
saving time is in effect in the local time zone, press 1 to
highlight On and press J.
7Set the date and time.
Select Date and time and
press 2.
Press 4 or 2 to select
an item, 1 or 3 to change.
Press J when the clock is set to
the current date and time.
32
s
8Set date format.
Select Date format and press
2.
Press 1 or 3 to choose the
order in which the year, month,
and day will be displayed and
press J.
9Exit to shooting mode.
Press the shutter-release button halfway
to exit to shooting mode.
AThe Clock Battery
The camera clock is powered by a separate, non-rechargeable CR1616
lithium battery with a life of about two years.
When this battery is low, a
B icon will be displayed in the top control panel while the standby
timer is on.
For information on replacing the clock battery, see page
406.
AThe Camera Clock
The camera clock is less accurate than most watches and household
clocks.
Check the clock regularly against more accurate time pieces and
reset as necessary.
AGPS Units (0231)
If a GPS unit (0394) is connected, the camera clock will be set to the
time and date provided by the GPS unit (0233).
33
s
Insert a Memory Card
Pictures are stored on memory cards (available separately; 0442).
The camera is equipped with two card slots, one for XQD and the
other for Type I CompactFlash cards.
Type II cards and microdrives
can not be used.
1Turn the camera off.
2Open the card slot cover.
Open the door protecting the card-slot
cover release button (q) and press the
release button (w) to open the card slot
(e).
DInserting and Removing Memory Cards
Always turn the camera off before inserting or removing memory
cards.
Power switch
34
s
3Insert the memory card.
XQD memory cards: Holding the card with
the rear label toward the monitor, slide it
into the XQD card slot until it clicks into
place.
The green access lamp will light
briefly.
CompactFlash memory cards: Insert the card
into the CompactFlash card slot with the
rear label toward the monitor (q).
When
the memory card is fully inserted, the
eject button will pop up (w) and the
green access lamp will light briefly.
4Close the card slot cover.
If this is the first time the memory card
will be used after being used or
formatted in another device, format the
card as described on page 36.
DInserting Memory Cards
After confirming that you are inserting the card into the correct
slot, insert the memory card terminals first.
Inserting the card into
the wrong slot or inserting it upside down or backwards could
damage the camera or the card.
Check to be sure that the card is in
the correct orientation.
XQD card CompactFlash card
Access lamp
Eject button
Direction of
insertion for
left (XQD)
card slot
Rear label
4 GB
Direction of
insertion for
right
(Compact-
Flash) card
slot
Rear label
35
s
AMemory Card Icons
The memory cards currently inserted in the
camera are indicated as shown (the example at
right shows the icons displayed when both an
XQD and a CompactFlash card are inserted).
If
the memory card is full or an error has occurred,
the icon for the affected card will flash (0426).
Top control panel
AUsing Two Memory Cards
See page 95 for information on choosing the roles played by each card
when two cards are inserted in the camera.
ARemoving Memory Cards
After confirming that the access lamp is off, turn the camera off and
open the memory card slot cover.
XQD memory cards: Press the card in to eject it (q).
The memory card can then be removed by hand.
CompactFlash memory cards: Press the eject button
(q) to partially eject the card (w).
The memory
card can then be removed by hand.
Do not push
on the memory card while pressing the eject
button. Failure to observe this precaution could
damage the camera or memory card.
36
s
Format the Memory Card
Memory cards must be formatted before first use or after being
used or formatted in other devices.
1Turn the camera on.
2Press the I (Q) and O
(Q) buttons.
Hold the I (Q) and O (Q)
buttons down simultaneously
until a flashing C appears
in the shutter-speed displays
in the top control panel and
viewfinder. If two memory
cards are inserted, the card to
be formatted is shown by a
flashing icon. By default, the
primary card slot (095) will
be selected; you can choose
the secondary slot by rotating
the main command dial. To exit without formatting the
memory card, wait until C stops flashing (about six
seconds) or press any button other than the I (Q) and
O (Q) buttons.
DFormatting Memory Cards
Formatting memory cards permanently deletes any data they may contain.
Be sure to copy any photographs and other data you wish to keep to a
computer before proceeding (0263).
O (Q) button I (Q) butto
n
37
s
3Press the I (Q) and O (Q) buttons again.
Press the I (Q) and O (Q) buttons together a second time
while C is flashing to format the memory card.
Do not
remove the memory card or remove or disconnect the power
source during formatting.
When formatting is complete, the top
control panel will show the number of
photographs that can be recorded at
current settings and the frame-count
displays will show B.
DMemory Cards
• Memory cards may be hot after use.
Observe due caution when
removing memory cards from the camera.
• Turn the power off before inserting or removing memory cards.
Do
not remove memory cards from the camera, turn the camera off, or
remove or disconnect the power source during formatting or while
data are being recorded, deleted, or copied to a computer.
Failure to
observe these precautions could result in loss of data or in damage to
the camera or card.
• Do not touch the card terminals with your fingers or metal objects.
• Do not bend, drop, or subject to strong physical shocks.
• Do not apply force to the card casing.
Failure to observe this
precaution could damage the card.
• Do not expose to water, high levels of humidity, or direct sunlight.
• Do not format memory cards in a computer.
ANo Memory Card
If no memory card is inserted, the top control
panel and viewfinder will show S.
If the
camera is turned off with a charged EN-EL18
battery and no memory card inserted, S
will be displayed in the top control panel.
ASee Also
See page 345 for information on formatting memory cards using the
Format memory card option in the setup menu.
38
s
Adjust Viewfinder Focus
The camera is equipped with diopter adjustment to accommodate
individual differences in vision.
Check that the display in the
viewfinder is in focus before shooting.
1Turn the camera on.
Remove the lens cap and turn the camera on.
2Lift the diopter adjustment control
(q).
3Focus the viewfinder.
Rotate the diopter adjustment control
(w) until the viewfinder display, focus
points, and AF area brackets are in sharp
focus.
When operating the control with
your eye to the viewfinder, be careful
not to put your fingers or fingernails in
your eye.
AF area brackets
Focus point
39
s
4Replace the diopter adjustment
control.
Push the diopter adjustment control
back in (e).
AAdjusting Viewfinder Focus
If you are unable to focus the viewfinder as described above, select
single-servo autofocus (AF-S; 097), single-point AF (0100), and the
center focus point (0103), and then frame a high-contrast subject in
the center focus point and press the shutter-release button halfway to
focus the camera.
With the camera in focus, use the diopter adjustment
control to bring the subject into clear focus in the viewfinder.
If
necessary, viewfinder focus can be further adjusted using optional
corrective lenses (0392).
ADiopter-Adjustment Viewfinder Lenses
Corrective lenses (available separately; 0392)
can be used to further adjust viewfinder
diopter. Before attaching a diopter-adjustment
viewfinder lens, remove the DK-17 viewfinder
eyepiece by closing the viewfinder shutter to
release the eyepiece lock (q) and then
unscrewing the eyepiece as shown at right (w).
40
s
Basic Photography and Playback
Turn the Camera On
Before taking photographs, turn the camera on and check the
battery level and number of exposures remaining as described
below.
1Turn the camera on.
Turn the camera on.
The
control panels will turn on and
the display in the viewfinder
will light.
2Check the battery level.
Check the battery level in the top control
panel or viewfinder.
Icon*
DescriptionControl panel Viewfinder
L— Battery fully charged.
K—
Battery partially discharged.J—
I—
HdLow battery.
Charge battery or ready
spare battery.
H
(flashes)
d
(flashes)
Shutter release disabled.
Charge or
exchange battery.
* No icon displayed when camera is powered by optional EP-6 power
connector and EH-6b AC adapter.
Power switch
41
s
3Check the number of exposures remaining.
The top control panel shows the
number of photographs that can be
taken at current settings (values over
1,000 are rounded down to the
nearest hundred; e.g., values between
2,900 and 2,999 are shown as 2.9 K).
If
two memory cards are inserted, the
displays show the space available on
the card in the primary slot (095).
When this number reaches zero, A will
flash in the exposure-count displays
while the shutter-speed displays will
show a flashing n or j and the
icon for the affected card will flash.
Insert another memory card or delete
some photos.
42
s
Ready the Camera
When framing photographs in the
viewfinder, hold the handgrip in your right
hand and cradle the camera body or lens
with your left.
Keep your elbows propped
lightly against your torso for support and
place one foot half a pace ahead of the
other to keep your upper body stable.
When framing photographs in portrait (tall)
orientation, hold the camera as shown in
the bottom of the three illustrations at right.
DFraming Photos in Portrait (Tall) Orientation
The camera is equipped with controls
for use in portrait (tall) orientation,
including a vertical shutter-release, Fn,
and B buttons, main and sub-
command dials, and multi selector
(0104, 338).
Rotate the vertical
shooting shutter-release button lock
to L to avoid accidentally operating
these controls when the camera is in
landscape (wide) orientation.
Vertical shooting shutter-
release button loc
k
43
s
Focus and Shoot
1Press the shutter-
release button
halfway (044).
At default settings, the
camera will focus on the
subject in the center
focus point. Frame a
photo in the viewfinder
with the main subject
positioned in the center
focus point and press the shutter-release button halfway.
2Check indicators in the viewfinder.
When the focus operation is complete, the in-focus indicator
(I) will appear in the viewfinder.
While the shutter-release button is pressed halfway,
focus will lock and the number of exposures that
can be stored in the memory buffer (“t”; 0113)
will be shown in the viewfinder display.
For information on what to do if the camera is unable to focus
using autofocus, see “Getting Good Results with Autofocus”
(0107).
Viewfinder display Description
ISubject in focus.
2Focus point is between camera and subject.
4Focus point is behind subject.
24
(flashes)
Camera unable to focus on subject in focus
point using autofocus.
Focus
indicator
Buffer
capacity
Focus point
44
s
3Shoot.
Smoothly press the shutter-
release-button the rest of the
way down to release the
shutter and record the
photograph.
While the
photograph is being recorded
to the memory card, the access lamp will light.
Do not eject the
memory card or remove or disconnect the power source until the
lamp has gone out and recording is complete.
AThe Shutter-Release Button
The camera has a two-stage shutter-release button.
The camera
focuses when the shutter-release button is pressed halfway.
To take the
photograph, press the shutter-release button the rest of the way down.
Access lamp
Focus Take photograph
45
s
AThe Standby Timer
The shutter speed and aperture displays in the top control panel and
viewfinder will turn off if no operations are performed for about six
seconds, reducing the drain on the battery.
Press the shutter-release
button halfway to reactivate the display in the viewfinder (044).
The length of time before the standby timer expires automatically can
be adjusted using Custom Setting c2 (Standby timer, 0316).
AThe Multi Selector
The multi selector can be used to select the
focus point while the exposure meters are on
(0103).
ACamera Off Display
If the camera is turned off with a battery and
memory card inserted, the memory card icon,
frame count, and number of exposures
remaining will be displayed (some memory
cards may in rare cases only display this
information when the camera is on).
Exposure meters on
Exposure meters off
Exposure meters on
Multi selector
Top control panel
46
s
Viewing Photographs
1Press the K button.
A photograph will be
displayed in the monitor.
The memory card
containing the picture
currently displayed is
shown by an icon.
2View additional pictures.
Additional pictures can be
displayed by pressing 4 or 2.
To view additional information
on the current photograph,
press 1 and 3 (0238).
To end playback and return to shooting mode, press the
shutter-release button halfway.
AImage Review
When On is selected for Image review in the playback menu (0289),
photographs are automatically displayed in the monitor after shooting.
ASee Also
See page 236 for information on choosing a memory card slot.
K button
0, 0
1
/
125 F5. 6
100 50
mm
100NC_D4
D
S
C_
0001. JP
G
15
/
04
/
2011 10:02:27
N
I
KO
N
D4
1
/
12
N
N
OR
OR
M
AL
AL
4928x3280
47
s
Deleting Unwanted Photographs
Unwanted photographs can be deleted by pressing the O (Q)
button.
Note that photographs can not be recovered once
deleted.
1Display the photograph.
Display the photograph you wish to
delete as described in “Viewing
Photographs” on the previous page.
The
location of the current image is shown
by an icon at the bottom left corner of
the display.
2Delete the photograph.
Press the O (Q) button.
A
confirmation dialog will be
displayed; highlight
Selected image and press
O (Q) again to delete the
image and return to
playback (for information on the All images option, see page
251).
To exit without deleting the picture, press K.
ADelete
To delete multiple images or to select the memory card from which
images will be deleted, use the Delete option in the playback menu
(0253).
O (Q) button
48
s
x
49
x
Live View Photography
Follow the steps below to take photographs in live view.
1Rotate the live view selector to
C(live view photography).
2Press the a button.
The mirror will be raised and the view
through the lens will be displayed in the
camera monitor.
The subject will no
longer be visible in the viewfinder.
3Position the focus point.
Position the focus point over your subject as described on
page 53.
Live view selector
a button
50
x
4Focus.
Press the shutter-release button
halfway or press the B
button to focus.
The focus point will flash green while the
camera focuses.
If the camera is able to
focus, the focus point will be displayed in
green; if the camera is unable to focus,
the focus point will flash red (note that
pictures can be taken even when the
focus point flashes red; check focus in the
monitor before shooting).
Exposure can
be locked by pressing the center of the sub-selector (0135);
focus locks while the shutter-release button is pressed
halfway.
AExposure Preview
During live view photography, you can
press J to preview the effects of shutter
speed, aperture, and ISO sensitivity on
exposure.
Exposure can be adjusted by
±5 EV (0137), although only values
between –3 and +3 EV are reflected in the
preview display.
Note that the preview
may not accurately reflect the final results when flash lighting is
used, Active D-Lighting (0184), High Dynamic Range (HDR;
0186), or bracketing is in effect, A (auto) is selected for the Picture
Control Contrast parameter (0176), or p is selected for
shutter speed. If the subject is very bright or very dark, the
exposure indicators will flash to warn that the preview may not
accurately reflect exposure.
Exposure preview is not available
when A is selected for shutter speed.
B button
Center of sub-
selector
51
x
5Take the picture.
Press the shutter-release button the rest
of the way down to shoot.
The monitor
will turn off.
6Exit live view mode.
Press the a button to exit live view
mode.
DUsing Autofocus in Live View
Use an AF-S lens.
The desired results may not be achieved with
other lenses or teleconverters.
Note that in live view, autofocus is
slower and the monitor may brighten or darken while the camera
focuses.
The focus point may sometimes be displayed in green
when the camera is unable to focus.
The camera may be unable to
focus in the following situations:
• The subject contains lines parallel to the long edge of the frame
• The subject lacks contrast
• The subject in the focus point contains areas of sharply
contrasting brightness, or includes spot lighting or a neon sign or
other light source that changes in brightness
• Flicker or banding appears under fluorescent, mercury-vapor,
sodium-vapor, or similar lighting
• A cross (star) filter or other special filter is used
• The subject appears smaller than the focus point
• The subject is dominated by regular geometric patterns (e.g.,
blinds or a row of windows in a skyscraper)
• The subject is moving
52
x
Focusing in Live View
To focus using autofocus, rotate the
focus-mode selector to AF and
follow the steps below to choose
autofocus and AF-area modes.
For
information on focusing manually,
see page 59.
❚❚ Choosing a Focus Mode
The following autofocus modes are available in live view:
To choose an autofocus mode, press the AF-mode button and
rotate the main command dial until the desired mode is displayed
in the monitor.
Mode Description
AF-S Single-servo autofocus: For stationary subjects.
Focus locks when
shutter-release button is pressed halfway.
AF-F
Full-time servo autofocus: For moving subjects.
Camera focuses
continuously until shutter-release button is pressed.
Focus locks
when shutter-release button is pressed halfway.
AF-mode
button
Main command
dial
Monitor
Focus-mode selector
53
x
❚❚ Choosing an AF-Area Mode
The following AF-area modes can be selected in live view:
Mode Description
!
Face-priority AF: Use for portraits. The camera automatically detects
and focuses on portrait subjects; the selected subject is indicated
by a double yellow border (if multiple faces, up to a maximum of
35, are detected, the camera will focus on the closest subject; to
choose a different subject, use the multi selector). If the camera
can no longer detect the subject (because, for example, the
subject has turned to face away from the camera), the border will
no longer be displayed.
5
Wide-area AF: Use for hand-held shots of landscapes and other non-
portrait subjects.
Use the multi selector to move the focus point
anywhere in the frame, or press the center of the multi selector to
position the focus point in the center of the frame.
6
Normal-area AF: Use for pin-point focus on a selected spot in the
frame.
Use the multi selector to move the focus point anywhere in
the frame, or press the center of the multi selector to position the
focus point in the center of the frame. A tripod is recommended.
&
Subject-tracking AF: Position the focus point over your subject and
press the center of the multi selector. The focus point will track the
selected subject as it moves through the frame. To end tracking,
press the center of the multi selector again.
DSubject Tracking
The camera may be unable to track subjects if they move quickly, leave
the frame or are obscured by other objects, change visibly in size, color,
or brightness, or are too small, too large, too bright, too dark, or similar
in color or brightness to the background.
54
x
To choose an AF-area mode, press the AF-mode button and rotate
the sub-command dial until the desired mode is displayed in the
monitor.
AF-mode
button
Sub-command dial Monitor
55
x
The Live View Display: Live View
Photography
Item Description 0
qTime remaining
The amount of time remaining before live
view ends automatically.
Displayed if
shooting will end in 30 s or less.
61, 67
wMonitor hue
indicator
Displayed if monitor hue differs from the hue
produced by the current white balance
setting.
56
eAutofocus mode The current autofocus mode. 52
rAF-area mode The current AF-area mode. 53
tFocus point The current focus point.
The display varies
with the option selected for AF-area mode. 49
yMonitor brightness
indicator A monitor brightness indicator. 57
uGuide A guide to the options available during live
view photography. 56, 57
t
y
u
w
q
r
e
56
x
❚❚ Adjusting Monitor Hue
If flash lighting is used with Flash or Preset manual white balance
(0153), the colors in the monitor may differ from those in the final
photograph.
Monitor hue can be adjusted to reduce the effects of
ambient lighting on the display in the monitor during live view
photography, for example when using a flash.
1Highlight the monitor hue
indicator.
Press and hold W and press 4 or 2 to
highlight the monitor hue indicator at
the left side of the display.
2Adjust monitor hue.
Keeping the W button pressed,
rotate the main command dial
to adjust monitor hue (select --
to preview the hue of the final
photograph in the monitor; if another option is selected when
Quiet is chosen for Live view photography in the shooting
menu (060), the hue seen in the monitor during live view
photography will differ from that seen in the final image).
Monitor hue is reset when the camera is turned off.
W button
57
x
❚❚ Adjusting Monitor Brightness
Monitor brightness can be adjusted as described below.
Note that
brightness adjustment is not available during exposure preview.
1Highlight the monitor brightness
indicator.
Press and hold W and press 4 or 2 to
highlight the monitor brightness
indicator at the right side of the
display.
2Adjust monitor brightness.
Keeping the W button pressed, press
1 or 3 to adjust monitor brightness
(note that monitor brightness has no effect on photographs
taken with the camera).
If A (auto) is selected and the monitor
is on, the camera will automatically adjust brightness in
response to ambient lighting conditions as measured by the
ambient brightness sensor (06).
ARecalling Monitor Hue
To restore the most recently selected hue when starting live view,
hold the U button while pressing a.
AChoosing a Picture Control
Pressing L (Z/Q) during
live view displays a list of
Picture Controls.
Highlight
the desired Picture Control
and press 2 to adjust
Picture Control settings
(0173). L (Z/Q) button
W button
58
x
The Information Display: Live View
Photography
To hide or display indicators in the monitor during live view
photography, press the R button.
Virtual horizon
(0358) Information on Information off
Histogram
(exposure
preview only;
050)
Framing
guides
59
x
Manual Focus
To focus in manual focus mode (0108),
rotate the lens focus ring until the subject is
in focus.
To magnify the view in the monitor up to
about 15 × for precise focus, press the X
button.
While the view through the lens is
zoomed in, a navigation window will appear
in a gray frame at the bottom right corner of
the display.
Use the multi selector to scroll
to areas of the frame not visible in the
monitor (available only if wide- or normal-
area AF is selected for AF-area mode), or
press W to zoom out.
ANon-CPU Lenses
When using non-CPU lenses, be sure to enter the focal length and
maximum aperture using the Non-CPU lens data option in the setup
menu (0228).
Non-CPU lenses can be used only in exposure modes g
and h (0125); aperture can be adjusted using the lens aperture ring.
AExposure
Depending on the scene, exposure may differ from that which would be
obtained when live view is not used.
Metering in live view is adjusted to
suit the live view display, producing photographs with exposure close
to what is seen in the monitor.
X button
Navigation window
60
x
Live View Shutter Release Options
The following options can be displayed by pressing G and
selecting Live view photography in the shooting menu:
Mode Description
MQuiet
Except when an optional flash unit is used, the mirror
remains up during live view photography, reducing noise
during shooting.
The noise of the shutter is still audible.
LSilent
The mirror remains up and the shutter stays open during live
view photography for less noise than
Quiet
mode;
L
is
displayed in the monitor. While the shutter-release button is
pressed, the camera will take up to five seconds of JPEG
photos at about 12 fps in continuous low-speed release
mode, or at about 24 fps in continuous high-speed release
mode; the time remaining is shown in the frame-count
display. In other release modes, one photo will be taken
each time the shutter-release button is pressed. ISO
sensitivity is set automatically except in exposure mode
h
,
when you can choose from values between ISO 200 and Hi 4
(
0
117). Exposure can be previewed in the monitor
0
50);
to view or hide an indicator (
0
130) showing the difference
between the selected by the camera and the value you have
selected, press
J
.
ASilent Mode
In silent mode, the flash will not fire, Active D-Lighting (0184), HDR
(0186), vignette control (0300), distortion control (0301), multiple
exposure (0210), and high ISO noise reduction (0302) turn off, and
image quality is fixed at JPEG fine.
Image size is determined solely by
the option selected for Image area and is unaffected by the option
selected for Image size:
•FX (36 × 24) 1.0×: 1,920 × 1,280
•1.2× (30 × 20) 1.2×: 1,600 × 1,064
•DX (24 × 16) 1.5×: 1,280 × 848
•5 : 4 (30 × 24): 1,600 × 1,280
61
x
Exposure preview is not available, matrix metering is selected
automatically, and the following settings can be adjusted.
Aperture Shutter speed ISO sensitivity
e, f———
g✔——
h✔✔✔
Note that silent mode is not completely silent: the shutter sounds and the
mirror is raised and lowered at the start and end of live view photography.
DThe Count Down Display
A count down will be displayed 30 s before live view ends automatically
(055; the timer turns red if live view is about to end to protect the
internal circuits or, if an option other than No limit is selected for
Custom Setting c4—Monitor off delay; 0317—5 s before the monitor
is due to turn off automatically).
Depending on shooting conditions,
the timer may appear immediately when live view is selected.
Note that
although the count down does not appear during playback, live view
will still end automatically when the timer expires.
AHDMI
If the camera is connected to an HDMI
video device during live view
photography, the camera monitor will
remain on and the video device will
display the view through the lens as
shown at right.
Press the R button to
turn the histogram display on and off during exposure preview (050).
ASee Also
For information on choosing the roles played by the center of the multi
selector and by the movie-record button and command dials, see
Custom Settings f1 (Multi selector center button, 0327) and f16
(Assign movie record button, 0339).
62
x
DShooting in Live View Mode
To prevent light entering via the viewfinder from interfering with
exposure, close the viewfinder eyepiece shutter (0114).
Although they will not appear in the final picture unless Silent is
selected for Live view photography (060), jagged edges, color
fringing, moiré, and bright spots may appear in the monitor, while
bright bands may appear in some areas with flashing signs and other
intermittent light sources or if the subject is briefly illuminated by a
strobe or other bright, momentary light source.
In addition, distortion
may occur if the camera is panned horizontally or an object moves at
high speed through the frame. Flicker and banding visible in the
monitor under fluorescent, mercury vapor, or sodium lamps can be
reduced using Flicker reduction (0348), although they may still be
visible in the final photograph at some shutter speeds.
When shooting
in live view mode, avoid pointing the camera at the sun or other strong
light sources.
Failure to observe this precaution could result in damage
to the camera’s internal circuitry.
Live view ends automatically if the lens is removed, the live view
selector is rotated to a new setting, or the G button is pressed.
Live view may end automatically to prevent damage to the camera’s
internal circuits; exit live view when the camera is not use.
Note that the
temperature of the camera’s internal circuits may rise and noise (bright
spots, randomly-spaced bright pixels, or fog) may be displayed in the
following instances (the camera may also become noticeably warm, but
this does not indicate a malfunction):
• The ambient temperature is high
• The camera has been used for extended periods in live view or to
record movies
• The camera has been used in continuous release mode for extended
periods
If live view does not start when you press the a button, wait for the
internal circuits to cool and then try again.
Movie recording is not available during live view photography and
pressing the movie-record button has no effect.
Select movie live view
(063) to shoot movies.
y
63
y
Movie Live View
Movies can be recorded in live view.
1Rotate the live view selector to 1
(movie live view).
2Press the a button.
The mirror will be raised and the view
through the lens will be displayed in the
camera monitor, modified for the effects
of exposure.
The subject will no longer
be visible in the viewfinder.
3Choose a focus mode (052).
DThe 0 Icon
A 0 icon (068) indicates that movies can not be recorded.
ABefore Recording
Before recording, choose a color space (0299) and Picture Control
(0173). White balance can be set at any time by pressing the U
button and rotating the main command dial (0153).
Live view selector
a button
64
y
4Choose an AF-area mode (053).
5Focus.
Frame the opening shot and focus as
described in Steps 3 and 4 on pages 49–
50 (for more information on focusing in
movie live view, see page 51).
Note that
the number of subjects that can be
detected in face-priority AF drops in
movie live view.
AExposure Mode
The following settings can be adjusted in movie live view:
Aperture Shutter speed ISO sensitivity Exposure compensation
e, f—— — ✔
g✔—— ✔
h✔✔ ✔ —
In exposure mode
h
, shutter speed can be set to values between
1
/
25
s and
1
/
8,000
s (the slowest available shutter speed varies with
the frame rate;
0
74).
In other exposure modes, shutter speed is
adjusted automatically.
If the subject is over- or under-exposed in
mode
e
or
f
, end live view and start movie live view again or select
exposure
g
and adjust aperture.
B button
65
y
6Start recording.
Press the movie-record button to start
recording.
A recording indicator and the
time available are displayed in the
monitor.
Exposure is set using matrix
metering and can be locked by pressing
the center of the sub-selector (0135) or
altered by up to ±3 EV using exposure
compensation (0137).
In autofocus
mode, the camera can be refocused by
pressing the AF-ON button.
AAudio
The camera can record both video and sound; do not cover the
microphone on the front of the camera during movie recording.
Note that the built-in microphone may record sounds made by the
lens during autofocus, vibration reduction, or changes to aperture.
ASee Also
Frame size, microphone sensitivity, card slot, and ISO sensitivity
options are available in the Movie settings menu (074).
Focus
can be adjusted manually as described on page 59.
The roles
played by the center of the multi selector, the Fn and Pv buttons,
and the center of the sub-selector can be chosen using Custom
Settings f1 (Multi selector center button; 0327), g1 (Assign Fn
button; 0340), g2 (Assign preview button; 0341), and g3
(Assign sub-selector center; 0342), respectively.
Custom Setting
g4 (Assign shutter button; 0343) controls whether the shutter-
release button can be used to start movie live view, or to start and
end movie recording, or (when pressed all the way down) to take
photographs during movie recording.
Movie-record button
Recording indicator
Time remaining
66
y
7End recording.
Press the movie-record button again to
end recording.
Recording will end
automatically when the maximum length
is reached, or the memory card is full.
AMaximum Length
The maximum length for individual movie files is 4 GB (for
maximum recording times, see page 74); note that depending on
memory card write speed, shooting may end before this length is
reached.
ATaking Photographs
To take a photograph while recording is in progress, press the
shutter-release button all the way down.
Movie recording will end
(the footage recorded to that point will be saved) and the camera
will return to live view.
Except at a frame size of 640 × 424, the
photograph will be recorded at the current image area setting with
an aspect ratio of 16 : 9.
Note that the exposure for photographs
can not be previewed during movie live view; mode e, f, or g is
recommended but accurate results can be achieved in mode h by
adjusting exposure during live view photography (049) and then
ending live view photography, starting movie live view, and
checking the image area.
Exposure compensation for the
photograph can be set to values between –5 and +5 EV, but only
values between –3 and +3 can be previewed in the monitor
(0137).
DFrame Size
The area used for metering exposure or auto white balance when
photographs are recorded at a movie frame size of 1920 × 1080;
30 fps; crop, 1920 × 1080; 25 fps; crop, or 1920 × 1080; 24 fps;
crop (074) is not the same as the area in the final photograph,
with the result that optimal results may not be achieved. Take test
shots and check the results in the monitor.
67
y
8Exit live view mode.
Press the a button to exit live view
mode.
Indices
If Index marking is selected for Custom
Setting g2 (Assign preview button; 0341),
you can press the Pv button during recording
to add indices that can be used to locate
frames during editing and playback (077).
Up to 20 indices can be added to each movie.
DThe Count-Down Display
A count down will be displayed 30 s before live view ends automatically
(055).
Depending on shooting conditions, the timer may appear
immediately when movie recording begins.
Note that regardless of the
amount of recording time available, live view will still end automatically
when the timer expires.
Wait for the internal circuits to cool before
resuming movie recording.
Pv button
Index
68
y
The Live View Display: Movie Live View
Item Description 0
q“No movie” icon Indicates that movies can not be recorded. —
wHeadphone volume Volume of audio output to headphones. 69
eMicrophone
sensitivity Microphone sensitivity for movie recording. 69
rSound level
Sound level for audio recording.
Displayed
in red if level is too high; adjust microphone
sensitivity accordingly.
Left (L) and right (R)
channel indicators appear when optional
ME-1 or other stereo microphone is used.
69
tMovie frame size The frame size for movie recording. 74
yTime remaining
(movie live view) The recording time available for movies. 65
uMonitor brightness
indicator A monitor brightness indicator. 69
iGuide A guide to the options available during
movie live view. 69
q
w
e
r
t
u
y
i
69
y
❚❚ Adjusting Settings in the Live View Display
Microphone sensitivity, headphone volume, and monitor
brightness can be adjusted as described below.
Note that
microphone sensitivity and headphone volume can not be
adjusted during recording, and that brightness affects the monitor
only (057); movies recorded with the camera are unaffected.
1Highlight a setting.
Press and hold W and press 4 or 2 to
highlight the indicator for the desired
setting.
2Adjust the highlighted setting.
Keeping the W button pressed, press
1 or 3 to adjust the highlighted
setting.
AUsing an External Microphone
The optional ME-1 stereo microphone can be used to record sound in
stereo or to avoid recording lens noise caused by autofocus (0395).
AHeadphones
Third-party headphones can be used.
Note that high sound levels may
result in high volume; particular care should be taken when
headphones are used.
W button
70
y
The Information Display: Movie Live View
To hide or display indicators in the monitor during movie live view,
press the R button.
Virtual horizon
(0358) Information on Information off
Histogram Framing
guides
AHDMI
If the camera is connected to an HDMI
device (0280), the view through the lens
will appear both in the camera monitor
and on the HDMI device.
The indicators
that appear in the HDMI device during
movie recording are shown at right.
The
camera monitor does not show the sound level, virtual horizon, or
histogram; indicators in the monitor and on the HDMI device can not be
hidden or displayed using the R button.
71
y
Image Area
Regardless of the option selected for Image area in the shooting
menu (088), all movies and photographs recorded in movie live
view have an aspect ratio of 16 : 9 (or 3 : 2 when the movie frame
size is 640 × 424). Images recorded with On selected for Image
area > Auto DX crop and a DX lens attached use a DX-based
movie format, as do images recorded with DX (24×16) 1.5×
selected for Image area > Choose image area. Other images use
an FX-based movie format.
A a icon is displayed when the DX-
based movie format is selected.
The differences between the
crops (086) displayed during viewfinder and live view
photography and movie live view photo crop are shown below.
The size of the area at the center of the image sensor used to
record photographs taken in movie live view is 35.0 × 19.7 mm
(16 : 9, FX-based movie format), 22.4 × 12.6 mm (16 : 9, DX-based
movie format), 35.0 × 23.4 mm (3 : 2, FX-based movie format), or
22.4 × 14.9 mm (3 : 2, DX-based movie format).
Crop for viewfinder and live view
photography
16 : 9 photo crop for movie live view
Crop for viewfinder and live view
photography
3 : 2 photo crop for movie live view
72
y
AMovie Live View Photographs
The following table shows the size of photographs (aspect ratio 16 : 9)
taken in movie live view at frame sizes other than 640 × 424:
Image area Option Size (pixels) Print size (cm/in.) *
FX-based format
(16 : 9)
Large 4,928 × 2,768 41.7 × 23.4/16.4 × 9.2
Medium 3,696 × 2,072 31.3 × 17.5/12.3 × 6.9
Small 2,464 × 1,384 20.9 × 11.7/ 8.2 × 4.6
DX-based format
(16 : 9)
Large 3,200 × 1,792 27.1 × 15.2/10.7 × 6.0
Medium 2,400 × 1,344 20.3 × 11.4/ 8.0 × 4.5
Small 1,600 × 896 13.5 × 7.6/ 5.3 × 3.0
1920 × 1080;
30 fps/25 fps/
24 fps; crop
— 1,920 × 1,080 16.3 × 9.1/ 6.4 × 3.6
The following table shows the size of photographs (aspect ratio 3 : 2)
taken in movie live view at frame sizes of 640 × 424:
Image area Option Size (pixels) Print size (cm/in.) *
FX-based movie
format (3 : 2)
Large 4,928 × 3,280 41.7 × 27.8/16.4 × 10.9
Medium 3,696 × 2,456 31.3 × 20.8/12.3 × 8.2
Small 2,464 × 1,640 20.9 × 13.9/ 8.2 × 5.5
DX-based movie
format (3 : 2)
Large 3,200 × 2,128 27.1 × 18.0/10.7 × 7.1
Medium 2,400 × 1,592 20.3 × 13.5/ 8.0 × 5.3
Small 1,600 × 1,064 13.5 × 9.0/ 5.3 × 3.5
* Approximate size when printed at 300 dpi.
Print size in inches equals
image size in pixels divided by printer resolution in dots per inch (dpi;
1 inch = approximately 2.54 cm).
Image quality is determined by the option selected for Image quality
in the shooting menu (090).
ARemote Cords
If Record movies is selected for Custom Setting g4 (Assign shutter
button), the shutter-release buttons on optional remote cords (0394)
can be used to start movie live view and to start and end movie
recording (0343).
73
y
DRecording Movies
Flicker, banding, or distortion may be visible in the monitor and in the
final movie under fluorescent, mercury vapor, or sodium lamps or if the
camera is panned horizontally or an object moves at high speed
through frame (for information on reducing flicker and banding, see
Flicker reduction, 0348).
Jagged edges, color fringing, moiré, and
bright spots may also appear.
Bright bands may appear in some areas
of the frame with flashing signs and other intermittent light sources or if
the subject is briefly illuminated by a strobe or other bright, momentary
light source.
When recording movies, avoid pointing the camera at the
sun or other strong light sources.
Failure to observe this precaution
could result in damage to the camera’s internal circuitry.
Note that
noise (randomly-spaced bright pixels, fog, or lines) and unexpected
colors may appear if you zoom in on the view through the lens (059)
during movie live view.
Flash lighting can not be used during movie live view.
Recording ends automatically if the lens is removed or the live view
selector is rotated to a new setting.
Movie live view ends when the G
button is pressed.
Live view may end automatically to prevent damage to the camera’s
internal circuits; exit live view when the camera is not use.
Note that the
temperature of the camera’s internal circuits may rise and noise (bright
spots, randomly-spaced bright pixels, or fog) may be displayed in the
following instances (the camera may also become noticeably warm, but
this does not indicate a malfunction):
• The ambient temperature is high
• The camera has been used for extended periods in live view or to
record movies
• The camera has been used in continuous release mode for extended
periods
If live view does not start when you press the a button, wait for the
internal circuits to cool and then try again.
74
y
Movie Settings
Use the Movie settings option in the shooting menu to adjust the
following settings.
•Frame size/frame rate, Movie quality: Choose from the following
options:
Maximum bit rate (Mbps) Maximum
length
Option1★ high quality Normal
11920 × 1080; 30 fps2, 3
24 12
29 min. 59 s
21920 × 1080; 25 fps2, 3
31920 × 1080; 24 fps2, 3
41280 × 720; 60 fps 3
51280 × 720; 50 fps 3
61280 × 720; 30 fps 12 8
71280 × 720; 25 fps
o640 × 424; 30 fps 53
p640 × 424; 25 fps
81920 × 1080; 30 fps; crop 3, 4
24 12
91920 × 1080; 25 fps; crop 3, 4
!1920 × 1080; 24 fps; crop 3, 4
1 Actual frame rate is 29.97 fps for values listed as 30 fps, 23.976 fps for values listed
as 24 fps, and 59.94 fps for values listed as 60 fps.
2 In DX-based movie format, image quality is equivalent to movies recorded at a
frame size of 1280 × 720.
3 Maximum length for ★ High quality movies is 20 minutes.
4 Matrix metering selected automatically.
Picture angle equivalent to a focal length
2.7× FX-based movie format length, allowing a telephoto effect without changing
to a longer lens; h is displayed in the monitor.
Photographs taken at this setting
are stored as JPEG fine images 1,920 × 1,080 pixels in size; HDR is not available
(0186).
DFrame Size and Rate
Frame size and rate affects the distribution and amount of noise
(randomly-spaced bright pixels, fog, or bright spots).
75
y
•Microphone: Turn the built-in or optional ME-1
stereo microphones on or off or adjust
microphone sensitivity.
Choose Auto
sensitivity to adjust sensitivity
automatically, Microphone off to turn
sound recording off; to select microphone
sensitivity manually, select Manual sensitivity and choose a
sensitivity.
•Destination: Choose the slot to which movies
are recorded.
The menu shows the time
available on each card; recording ends
automatically when no time remains.
Note
that regardless of the option selected,
photographs are recorded to the card in the
primary slot (095).
•ISO sensitivity range: Choose the range of ISO
sensitivities available during movie
recording.
Note that at high ISO sensitivities
the camera may have trouble focusing and
noise (randomly-spaced bright pixels, fog,
or lines) may increase.
76
y
1Select Movie settings.
Press the G button to
display the menus.
Highlight Movie settings in
the shooting menu and
press 2.
2Choose movie options.
Highlight the desired item
and press 2, then highlight
an option and press J.
G button
77
y
Viewing Movies
Movies are indicated by a 1 icon in full-frame playback (0235).
Press the center of the multi selector to start playback.
The following operations can be performed:
1 icon Length Current position/total length
Movie progress
bar
Volume Guide
To Use Description
Pause Pause playback.
Play Resume playback when movie is paused or
during rewind/advance.
Rewind/
advance
Speed increases with
each press, from 2× to
4× to 8× to 16×; keep pressed to skip to
beginning or end of movie (first frame is
indicated by
h
in top right corner of monitor,
last frame by
i
). If playback is paused, movie
rewinds or advances one frame at a time; hold
for continuous rewind or advance.
78
y
Skip ahead/
back
Use main command dial to skip to next or
previous index, or to skip to the last or first
frame if the movie contains no indices (if the
movie is more than 30 s long, rotating the
main command dial when the last frame is
displayed skips back 30 s.).
Adjust volume X/WPress X to increase volume, W to decrease.
Trim movie JSee page 79 for more information.
Return to
shooting mode
Press the shutter-release button halfway to
exit to shooting mode.
Display menus GSee page 283 for more information.
Exit /KExit to full-frame playback.
AThe p Icon
Movies with indices (067) are indicated by a
p icon in full-frame playback.
AThe 2 Icon
2 is displayed in full-frame and movie playback if
the movie was recorded without sound.
To Use Description
79
y
Editing Movies
Trim footage to create edited copies of movies or save selected
frames as JPEG stills.
Trimming Movies
To create trimmed copies of movies:
1Display a movie full
frame.
Press the K button to
display pictures full frame
in the monitor and press 4
and 2 to scroll through
pictures until the movie you
wish to edit is displayed.
2Choose a starting or end
point.
Play the movie back as
described on page 77,
pressing the center of the
multi selector to start and
resume playback and 3 to
pause, or rotating the main command dial to skip to an index
(067).
Your approximate position in the movie can be
ascertained from the movie progress bar.
Option Description
9Choose start/end point Create a copy from which the opening or closing
footage has been removed.
4Save selected frame Save a selected frame as a JPEG still.
K button
Movie progress bar
80
y
3Display movie edit
options.
Press J to display movie
edit options.
4Select Choose start/end
point.
Highlight Choose start/
end point and press J.
The dialog shown at right
will be displayed; choose
whether the current frame
will be the starting or end
point of the copy and press
J.
J button
81
y
5Delete frames.
If the desired frame is not
currently displayed, press
4 or 2 to advance or
rewind (to skip to an index,
rotate the main command
dial).
To switch the current
selection from start point (w) to end point (x) or vice versa,
press L (Z/Q).
Once you have selected the start point
and/or end point, press 1.
All frames
before the selected start point and after
the selected end point will be removed
from the copy.
6Save the copy.
Highlight one of the
following and press J:
•Save as new file: Save the
copy to a new file.
•Overwrite existing file: Replace the original movie file with the
edited copy.
•Cancel: Return to Step 5.
•Preview: Preview the copy.
Edited copies are indicated by a 9 icon in full-frame playback.
L (Z/Q) button
82
y
DTrimming Movies
Movies must be at least two seconds long.
If a copy can not be created
at the current playback position, the current position will be displayed
in red in Step 5 and no copy will be created.
The copy will not be saved
if there is insufficient space available on the memory card.
Copies have the same time and date of creation as the original.
AThe Retouch Menu
Movies can also be edited using the Edit movie
option in the retouch menu (0361).
83
y
Saving Selected Frames
To save a copy of a selected frame as a JPEG still:
1View the movie and
choose a frame.
Play the movie back as
described on page 77; your
approximate position in the
movie can be ascertained from the movie progress bar.
Pause
the movie at the frame you intend to copy.
2Display movie edit
options.
Press J to display movie
edit options.
3Choose Save selected
frame.
Highlight Save selected
frame and press J.
4Create a still copy.
Press 1 to create a still copy
of the current frame.
J button
84
y
5Save the copy.
Highlight Ye s and press J
to create a fine-quality
(090) JPEG copy of the
selected frame.
Movie stills
are indicated by a 9 icon in full-frame playback.
ASave Selected Frame
JPEG movie stills created with the Save selected frame option can not
be retouched.
JPEG movie stills lack some categories of photo
information (0238).
d
85
d
Image Recording Options
Choose the aspect ratio and angle of view (image area).
Thanks to
the camera’s FX format (36.0 × 23.9 mm) image sensor, you can
choose from angles of view as wide as those supported by 35 mm
(135) format film cameras, while automatically cropping pictures
to the DX angle of view when using DX format lenses.
See page
444 for information on the number of pictures that can be stored
at different image area settings.
❚❚ Auto DX Crop
Choose whether to automatically select a DX
crop when a DX lens is attached.
Image Area
Option Description
On
Camera automatically selects DX crop when DX lens is
attached. If another lens is attached, the crop selected for
Choose image area will be used.
Off Crop selected for Choose image area is used.
86
d
❚❚ Choose Image Area
Choose the image area used when a non-DX
lens is attached or a DX-lens is attached with
Off selected for Auto DX crop (088).
Option Description
c
FX (36×24)
1.0×
(FX format)
Images are recorded in FX format using the full area
of the image sensor (36.0 × 23.9 mm), producing an
angle of view equivalent to a NIKKOR lens on a
35 mm format camera.
Z1.2× (30×20)
1.2×
A 29.9 × 19.9 mm area at the center of the image
sensor is used to record photographs.
To calculate
the approximate focal length of the lens in 35 mm
format, multiply by 1.2.
a
DX (24×16)
1.5×
(DX format)
An area at the center of the image sensor
23.4 × 15.5 mm is used to record pictures in DX
format.
To calculate the approximate focal length of
the lens in 35 mm format, multiply by 1.5.
b5:4(30×24) Pictures are recorded with an aspect ratio of 5 : 4
(29.9 × 23.9 mm).
DX format (24×16)
image circle
FX format (36×24)
image circle
FX format
1.2×
5:4
DX format
87
d
AImage Area
The selected option is shown in the information
display.
ADX Lenses
DX lenses are designed for use with DX format cameras and have a
smaller angle of view than lenses for 35 mm format cameras.
If Auto DX
crop is off and an option other than DX (24×16) (DX format) is selected
for Image area when a DX lens is attached, the edges of the image may
be eclipsed.
This may not be apparent in the viewfinder, but when the
images are played back you may notice a drop in resolution or that the
edges of the picture are blacked out.
AThe Viewfinder Display
The 1.2 ×, DX format, and 5 : 4 crops are shown below.
1.2× DX format 5 : 4
ASee Also
See page 71 for information on the crops available in movie live view.
88
d
Image area can be set using the Image area option in the
shooting menu or by pressing a control and rotating a command
dial.
❚❚ The Image Area Menu
1Select Image area in
the shooting menu.
Press G to display the
menus.
Highlight Image
area in the shooting
menu (0293) and press
2.
2Choose an option.
Highlight Auto DX crop or
Choose image area and
press 2.
3Adjust settings.
Choose an option and
press J.
The selected crop
is displayed in the
viewfinder (087).
DAuto DX Crop
The controls listed on page 89 can not be used to select image area
when a DX lens is attached and Auto DX crop is on.
AImage Size
Image size varies with the option selected for image area.
G button
J button
89
d
❚❚ Camera Controls
1Assign image area selection to a camera control.
Select Choose image area as the “press + command dials”
option for a camera control in the Custom Settings menu
(0332).
Image area selection can be assigned to the Fn
button (Custom Setting f3, Assign Fn button, 0328), the Pv
button (Custom Setting f4, Assign preview button, 0333),
the center of the sub-selector (Custom Setting f6, Assign sub-
selector center, 0333), or the movie-record button (Custom
Setting f16, Assign movie record button, 0339).
2Use the selected control to choose an image area.
The image area can be
selected by pressing the
selected control and rotating
the main or sub-command
dial until the desired crop is
displayed in the viewfinder
(087).
The option currently selected
for image area can be viewed by
pressing the control to display the image
area in the top control panel or
information display.
FX format is
displayed as “36 × 24”, 1.2 × as “30 × 20”,
DX format as “24 × 16”, and 5 : 4 as
“30 × 24”.
Main
command dial
Fn button
90
d
Image Quality
The D4 supports the following image quality options.
See page
444 for information on the number of pictures that can be stored
at different image quality and size settings.
Option File type Description
NEF (RAW) NEF
RAW data from the image sensor are saved
directly to the memory card in Nikon Electronic
Format (NEF).
Settings such as white balance
and contrast can be adjusted after shooting.
TIFF (RGB) TIFF
(RGB)
Record uncompressed TIFF-RGB images at a bit
depth of 8 bits per channel (24-bit color).
TIFF is
supported by a wide variety of imaging
applications.
JPEG fine
JPEG
Record JPEG images at a compression ratio of
roughly 1:4 (fine image quality). *
JPEG normal Record JPEG images at a compression ratio of
roughly 1:8 (normal image quality). *
JPEG basic Record JPEG images at a compression ratio of
roughly 1:16 (basic image quality). *
NEF (RAW)+
JPEG fine
NEF/
JPEG
Two images are recorded, one NEF (RAW) image
and one fine-quality JPEG image.
NEF (RAW)+
JPEG normal
Two images are recorded, one NEF (RAW) image
and one normal-quality JPEG image.
NEF (RAW)+
JPEG basic
Two images are recorded, one NEF (RAW) image
and one basic-quality JPEG image.
*Size priority selected for JPEG compression.
91
d
Image quality is set by pressing
the T button and rotating the
main command dial until the
desired setting is displayed in the
rear control panel.
ANEF (RAW) Images
NEF (RAW) images can be viewed on the camera or using software such
as Capture NX 2 (available separately; 0393) or ViewNX 2 (available on
the supplied ViewNX 2 installer CD).
JPEG copies of NEF (RAW) images
can be created using the NEF (RAW) processing option in the retouch
menu (0372).
ANEF+JPEG
When photographs taken at settings of NEF (RAW) + JPEG are viewed
on the camera with only one memory card inserted, only the JPEG
image will be displayed.
If both copies are recorded to the same
memory card, both copies will be erased when the photo is deleted.
If
the JPEG copy is recorded to a separate memory card using the
Secondary slot function > RAW primary, JPEG secondary option,
deleting the JPEG copy will not delete the NEF (RAW) image.
AThe Image Quality Menu
Image quality can also be adjusted using the
Image quality option in the shooting menu
(0293).
T button Main
command dial
Rear control panel
92
d
The following options can be
accessed from the shooting
menu.
Press the G button to
display the menus, highlight
the desired option and press 2.
❚❚ JPEG Compression
Choose the type of compression for JPEG images.
❚❚ NEF (RAW) Recording > Type
Choose the type of compression for NEF (RAW) images.
❚❚ NEF (RAW) Recording > NEF (RAW) Bit Depth
Choose a bit depth for NEF (RAW) images.
Option Description
OSize priority Images are compressed to produce relatively
uniform file size.
POptimal
quality
Optimal image quality.
File size varies with scene
recorded.
Option Description
NLossless
compressed
NEF images are compressed using a reversible
algorithm, reducing file size by about 20–40%
with no effect on image quality.
OCompressed
NEF images are compressed using a non-
reversible algorithm, reducing file size by about
35–55% with almost no effect on image quality.
Uncompressed NEF images are not compressed.
Option Description
q12-bit NEF (RAW) images are recorded at a bit-depth of 12 bits.
r14-bit
NEF (RAW) images are recorded at a bit depth of 14 bits,
producing files larger than those with a bit depth of
12 bits but increasing the color data recorded.
G button
93
d
Image Size
Image size is measured in pixels.
Choose from #Large, $Medium,
or %Small (note that image size varies depending on the option
selected for Image area, 085):
Image size can be set by pressing
the T button and rotating the
sub-command dial until the
desired option is displayed in the
rear control panel.
Image area Option Size (pixels) Print size (cm/in.) *
FX (36×24) 1.0×
(FX format)
Large 4,928 × 3,280 41.7 × 27.8/16.4 × 10.9
Medium 3,696 × 2,456 31.3 × 20.8/12.3 × 8.2
Small 2,464 × 1,640 20.9 × 13.9/ 8.2 × 5.5
1.2× (30×20)
1.2×
Large 4,096 × 2,720 34.7 × 23.0/13.7 × 9.1
Medium 3,072 × 2,040 26.0 × 17.3/10.2 × 6.8
Small 2,048 × 1,360 17.3 × 11.5/ 6.8 × 4.5
DX (24×16) 1.5×
(DX format)
Large 3,200 × 2,128 27.1 × 18.0/10.7 × 7.1
Medium 2,400 × 1,592 20.3 × 13.5/ 8.0 × 5.3
Small 1,600 × 1,064 13.5 × 9.0/ 5.3 × 3.5
5 : 4 (30×24)
Large 4,096 × 3,280 34.7 × 27.8/13.7 × 10.9
Medium 3,072 × 2,456 26.0 × 20.8/10.2 × 8.2
Small 2,048 × 1,640 17.3 × 13.9/ 6.8 × 5.5
* Approximate size when printed at 300 dpi. Print size in inches equals image
size in pixels divided by printer resolution in dots per inch
(dpi; 1 inch = approximately 2.54 cm).
T button Sub-command
dial
Rear control panel
94
d
ANEF (RAW) Images
Note that the option selected for image size does not affect the size of
NEF (RAW) images.
When opened in software such as ViewNX 2
(supplied) or Capture NX 2 (available separately), NEF (RAW) images
have the dimensions given for large (#-size) images in the table on the
previous page.
AThe Image Size Menu
Image size can also be adjusted using the Image
size option in the shooting menu (0293).
95
d
Using Two Memory Cards
When two memory cards are inserted in the camera, you can
choose one as the primary card using the Primary slot selection
item in the shooting menu.
Select XQD card slot to designate the
card in the XQD card slot as the primary card, CF card slot to
choose the CompactFlash card.
The roles played by the primary
and secondary cards can be chosen using the Secondary slot
function option in the shooting menu.
Choose from Overflow
(the secondary card is used only when the primary card is full),
Backup (each picture is recorded to both the primary and
secondary card), and RAW primary, JPEG secondary (as for
Backup, except that the NEF/RAW copies of photos recorded at
settings of NEF/RAW + JPEG are recorded only to the primary card
and the JPEG copies only to the secondary card).
D“Backup” and “RAW Primary, JPEG Secondary”
The camera shows the number of exposures remaining on the card with
the least amount of memory.
Shutter release will be disabled when
either card is full.
Voice memos (0255) are appended to the copy
recorded to the memory card in the primary slot.
ARecording Movies
When two memory cards are inserted in the camera, the slot used to
record movies can be selected using the Movie settings > Destination
option in the shooting menu (075).
96
d
N
97
N
Focus
This section describes the options that control how your camera
focuses when photographs are framed in the viewfinder.
Focus
can be adjusted automatically or manually (0108).
The user can
also select the focus point for automatic or manual focus (0103)
or use focus lock to focus to recompose photographs after
focusing (0105).
To use autofocus, rotate the focus-
mode selector to AF.
Autofocus Mode
Choose from the following autofocus modes:
Autofocus
Mode Description
AF-S
Single-servo autofocus: For stationary subjects.
Focus locks when
shutter-release button is pressed halfway.
At default settings,
shutter can only be released when in-focus indicator (I) is
displayed (focus priority; 0308).
AF-C
Continuous-servo autofocus: For moving subjects.
Camera focuses
continuously while shutter-release button is pressed halfway; if
subject moves, camera will engage predictive focus tracking (099)
to predict final distance to subject and adjust focus as necessary.
At default settings, shutter can be released whether or not subject
is in focus (release priority; 0307).
Focus-mode selector
98
N
Autofocus mode can
be selected by
pressing the AF-mode
button and rotating
the main command
dial until the desired
setting is displayed in
the viewfinder and
top control panel.
ASee Also
For information on using focus priority in continuous-servo autofocus,
see Custom Setting a1 (AF-C priority selection, 0307).
For
information on using release priority in single-servo autofocus, see
Custom Setting a2 (AF-S priority selection, 0308).
For information on
preventing the camera from focusing when the shutter-release button
is pressed halfway, see Custom Setting a4 (AF activation, 0309).
See
page 52 for information on the autofocus options available in live view
or during movie recording.
AF-mode button Main command dial
Top control panel Viewfinder
99
N
AThe B Buttons
For the purpose of focusing the camera, pressing
either of the B buttons has the same effect as
pressing the shutter-release button halfway
(note that the B button for vertical shooting
can only be used when the vertical shooting
shutter-release button lock is unlocked; 042).
APredictive Focus Tracking
In AF-C mode, the camera will initiate predictive
focus tracking if the subject moves toward or
away from the camera while the shutter-release
button is pressed halfway or either of the B
buttons is pressed.
This allows the camera to
track focus while attempting to predict where
the subject will be when the shutter is released.
B button
B button for
vertical shooting
100
N
AF-Area Mode
Choose how the focus point for autofocus is selected.
•Single-point AF: Select the focus point as described on page 103;
the camera will focus on the subject in the selected focus point
only.
Use with stationary subjects.
•Dynamic-area AF: Select the focus point as described on page 103.
In AF-C focus mode, the camera will focus based on information
from surrounding focus points if the subject briefly leaves the
selected point.
The number of focus points varies with the mode
selected:
-9-point dynamic-area AF: Choose when there is time to compose
the photograph or when photographing subjects that are
moving predictably (e.g., runners or race cars on a track).
-21-point dynamic-area AF: Choose when photographing subjects
that are moving unpredictably (e.g., players at a football game).
-51-point dynamic-area AF: Choose when photographing subjects
that are moving quickly and can not be easily framed in the
viewfinder (e.g., birds).
•3D-tracking: Select the focus point as described on page 103.
In
AF-C focus mode, the camera will track subjects that leave the
selected focus point and select new focus points as required.
Use to quickly compose pictures with subjects that are moving
erratically from side to side (e.g., tennis players).
If the subject
leaves viewfinder, remove your finger from the shutter-release
button and recompose the photograph with the subject in the
selected focus point.
101
N
•Auto-area AF: The camera automatically
detects the subject and selects the focus
point; if a face is detected, the camera will
give priority to the portrait subject.
The
active focus points are highlighted briefly
after the camera focuses; in AF-C mode, the
main focus point remains highlighted after
the other focus points have turned off.
AF-area mode can be
selected by pressing
the AF-mode button
and rotating the sub-
command dial until
the desired setting is
displayed in the
viewfinder and top
control panel.
A3D-tracking
When the shutter-release button is pressed halfway, the colors in the
area surrounding the focus point are stored in the camera.
Consequently 3D-tracking may not produce the desired results with
subjects that are the same color as the background or that occupy a
very small area of the frame.
AF-mode button Sub-command dial
Top control panel Viewfinder
102
N
AAF-Area Mode
AF-area mode is shown in the top control panel and viewfinder.
AF-area mode
Top control
panel
Viewfinder
AF-area mode
Top control
panel Viewfinder
Single-point
AF
51-point
dynamic-area
AF *
9-point
dynamic-area
AF *
3D-tracking
21-point
dynamic-area
AF *
Auto-area AF
* Only active focus point is displayed in the viewfinder.
Remaining focus
points provide information to assist focus operation.
AManual Focus
Single-point AF is automatically selected when manual focus is used.
ASee Also
For information on adjusting how long the camera waits before
refocusing when an object moves in front of the camera, see Custom
Setting a3 (Focus tracking with lock-on, 0309).
See page 53 for
information on the autofocus options available in live view or during
movie recording.
103
N
Focus Point Selection
The camera offers a choice of 51 focus points that can be used to
compose photographs with the main subject positioned almost
anywhere in the frame.
1Rotate the focus selector
lock to ●.
This allows the multi selector to
be used to select the focus
point.
2Select the focus point.
Use the multi selector to select
the focus point in the
viewfinder while the exposure
meters are on.
The center
focus point can be selected by
pressing the center of the multi
selector.
The focus selector lock can be
rotated to the locked (L)
position following selection to
prevent the selected focus
point from changing when the
multi selector is pressed.
Focus selector lock
104
N
AThe Sub-selector
The sub-selector can be used in place
of the multi selector to select the
focus point.
Press the center of the
sub-selector to lock exposure (0135)
and focus (0105).
Be careful not to
put your fingers or fingernails in your
eye when using the sub-selector.
APortrait (Tall-Orientation) Photographs
When framing shots in portrait (“tall”) orientation, use the multi selector
for vertical shooting to select the focus point.
For more information, see
Custom Setting f14 (Assign multi selector (vert.), 0338).
AUsing the Sub-selector and Multi Selector
for Vertical Shooting
Use as shown at right. Pressing the sides may not
have the desired effect.
AAuto-area AF
The focus point for auto-area AF is selected automatically; manual
focus-point selection is not available.
ASee Also
For information on choosing when the focus point is illuminated, see
Custom Setting a5 (Focus point illumination, 0310).
For information
on setting focus-point selection to “wrap around,” see Custom Setting
a6 (Focus point wrap-around, 0310).
For information on choosing
the number of focus points that can be selected using the multi
selector, see Custom Setting a7 (Number of focus points, 0311).
For
information on choosing separate focus points for vertical and
horizontal orientations, see Custom Setting a10 (Store points by
orientation, 0312).
For information on changing the role of the multi
selector center button, see Custom Setting f1 (Multi selector center
button, 0327).
For information on changing the role played by the
sub-selector, see Custom Settings f5 (Assign sub-selector, 0333) and
f6 (Assign sub-selector center, 0333).
Sub-selector
Center of sub-selector
105
N
Focus Lock
Focus lock can be used to change the composition after focusing,
making it possible to focus on a subject that will not be in a focus
point in the final composition.
If the camera is unable to focus
using autofocus (0107), focus lock can also be used to recompose
the photograph after focusing on another object at the same
distance as your original subject.
Focus lock is most effective
when an option other than auto-area AF is selected for AF-area
mode (0100).
1Focus.
Position the subject in the
selected focus point and press
the shutter-release button
halfway to initiate focus.
Check
that the in-focus indicator (I) appears in the viewfinder.
2Lock focus.
AF-C focus mode (097): With the
shutter-release button pressed
halfway (q), press the center of
the sub-selector (w) to lock
both focus and exposure (an
AE-L icon will be displayed in
the viewfinder).
Focus will
remain locked while the center
of the sub-selector is pressed,
even if you later remove your
finger from the shutter-release
button.
Shutter-release button
Center of sub-selector
106
N
AF-S focus mode: Focus locks automatically when the in-focus
indicator appears, and remain locked until you remove your
finger from the shutter-release button.
Focus can also be
locked by pressing the center of the sub-selector (see above).
3Recompose the photograph
and shoot.
Focus will remain locked
between shots if you keep the
shutter-release button pressed
halfway (AF-S) or keep the center of the sub-selector pressed,
allowing several photographs in succession to be taken at the
same focus setting.
Do not change the distance between the camera and the subject
while focus lock is in effect.
If the subject moves, focus again at the
new distance.
ALocking Focus with the B Button
During viewfinder photography, focus can be locked using either of the
B buttons in place of the shutter-release button (099). If AF-ON
only is selected for Custom Setting a4 (AF activation, 0309), the
camera will not focus when the shutter-release button is pressed
halfway; instead, the camera will focus when an B button is pressed,
at which point focus will lock and remain locked until either B
button is pressed again. The shutter can be released at any time,
regardless of the options selected for Custom Settings a1 (AF-C priority
selection, 0307) and a2 (AF-S priority selection, 0308), and the in-
focus indicator will not be displayed in the viewfinder.
ASee Also
See Custom setting c1 (Shutter-release button AE-L, 0316) for
information on using the shutter-release button to lock exposure,
Custom Setting f6 (Assign sub-selector center, 0333) for information
on choosing the role played by the center of the sub-selector.
107
N
AGetting Good Results with Autofocus
Autofocus does not perform well under the conditions listed below.
The shutter release may be disabled if the camera is unable to focus
under these conditions, or the in-focus indicator (●) may be displayed
and the camera may sound a beep, allowing the shutter to be released
even when the subject is not in focus.
In these cases, use manual focus
(0108) or use focus lock (0105) to focus on another subject at the
same distance and then recompose the photograph.
There is little or no contrast between the subject and
the background.
Example: Subject is the same color as the
background.
The focus point contains objects at different distances
from the camera.
Example: Subject is inside a cage.
The subject is dominated by regular geometric
patterns.
Example: Blinds or a row of windows in a skyscraper.
The focus point contains areas of sharply contrasting
brightness.
Example: Subject is half in the shade.
Background objects appear larger than the subject.
Example: A building is in the frame behind the
subject.
The subject contains many fine details.
Example: A field of flowers or other subjects that are
small or lack variation in brightness.
108
N
Manual Focus
Manual focus is available for lenses that do not support autofocus
(non-AF NIKKOR lenses) or when the autofocus does not produce
the desired results (0107).
•AF-S lenses: Set the lens focus mode switch to M.
•AF lenses: Set the lens focus mode
switch (if present) and camera
focus-mode selector to M.
•Manual focus lenses: Set the camera focus-mode selector to M.
To focus manually, adjust the lens focus ring
until the image displayed on the clear matte
field in the viewfinder is in focus.
Photographs can be taken at any time, even
when the image is not in focus.
DAF Lenses
Do not use AF lenses with the lens
focus mode switch set to M and
the camera focus-mode selector
set to AF.
Failure to observe this
precaution could damage the
camera or lens.
Focus-mode selector
109
N
The Electronic Rangefinder
If the lens has a maximum aperture of f/5.6
or faster, the viewfinder focus indicator can
be used to confirm whether the subject in
the selected focus point is in focus (the
focus point can be selected from any of the
51 focus points).
After positioning the
subject in the selected focus point, press
the shutter-release button halfway and
rotate the lens focus ring until the in-focus
indicator (I) is displayed.
Note that with
the subjects listed on page 107, the in-
focus indicator may sometimes be
displayed when the subject is not in focus;
confirm focus in the viewfinder before
shooting.
AFocal Plane Position
To determine the distance between
your subject and the camera, measure
from the focal plane mark (E) on the
camera body.
The distance between
the lens mounting flange and the focal
plane is 46.5 mm (1.83 in.).
Focal plane mark
46.5 mm
110
N
k
111
k
Release Mode
To choose a release mode, press the release
mode dial lock release and turn the release
mode dial to the desired setting.
Choosing a Release Mode
Mode Description
SSingle frame: Camera takes one photograph each time shutter-
release button is pressed.
CL
Continuous low speed: While shutter-release button is held down,
camera records photographs at the frame rate selected for Custom
Setting d2 (Shooting speed, 0318) > Continuous low-speed
(0112).
CH
Continuous high speed: While shutter-release button is held down,
camera records photographs at the frame rate selected for Custom
Setting d2 (Shooting speed, 0318) > Continuous high-speed
(0112). Use for active subjects.
J
Quiet shutter-release: As for single-frame except that noise is reduced by
disabling beeps and minimizing sound produced when mirror drops
back into place.
Beep does not sound when camera focuses
regardless of setting selected for Custom Setting d1 (Beep; 0318)
and mirror does not drop back into place until shutter-release button
is returned to halfway position after shooting, allowing you to delay
noise made by mirror.
Mirror is quieter than in single-frame mode.
ESelf-timer: Use self-timer for self-portraits or to reduce blurring
caused by camera shake (0114).
MUP
Mirror up: Choose this mode to minimize camera shake in telephoto
or close-up photography or in other situations in which the slightest
camera movement can result in blurred photographs (0116).
112
k
Continuous Release Modes
In continuous low speed mode, the camera records photographs
at the frame rate selected for Custom Setting d2 (Shooting speed,
0318) > Continuous low-speed.
In continuous high speed
mode, the maximum frame rate can be chosen from 10 and 11 fps
using Custom Setting d2 (Shooting speed, 0318) > Continuous
high-speed (note that at 11 fps, some of the second and
subsequent shots in each burst may not be in focus and exposure
may not accurately track poorly lit subjects).
The foregoing frame rates assume continuous-servo AF, manual or
shutter-priority auto exposure, a shutter speed of 1/250 s or faster,
and other settings at default values. Frame rates may drop at
extremely small apertures (high f-numbers) or slow shutter
speeds, when vibration reduction (available with VR lenses) or
auto ISO sensitivity control (0119) is on, or when the battery is
low.
113
k
ABuffer Size
The approximate number of images that can
be stored in the memory buffer at current
settings is shown in the exposure-count
displays in the viewfinder and top control
panel while the shutter-release button is
pressed halfway. The illustration at right
shows the display when space remains in the buffer for about 79
pictures.
AThe Memory Buffer
The camera is equipped with a memory buffer for temporary storage,
allowing shooting to continue while photographs are being saved to
the memory card. Up to 200 photographs can be taken in succession;
note, however, that frame rate will drop when the buffer is full (t00).
While photographs are being recorded to the memory card, the access
lamp will light. Depending on shooting conditions and memory card
performance, recording may take from a few seconds to a few minutes.
Do not remove the memory card or remove or disconnect the power source
until the access lamp has gone out. If the camera is switched off while
data remain in the buffer, the power will not turn off until all images in
the buffer have been recorded. If the battery is exhausted while images
remain in the buffer, the shutter release will be disabled and the images
transferred to the memory card.
ASee Also
For information on choosing the maximum number of photographs
that can be taken in a single burst, see Custom Setting d3 (Max.
continuous release, 0319). For information on the number of
pictures that can be taken in a single burst, see page 444.
114
k
Self-Timer Mode
The self-timer can be used to reduce camera shake or for self-
portraits.
1Mount the camera on a tripod.
Mount the camera on a tripod or place the camera on a stable,
level surface.
2Select self-timer mode.
Press the release mode dial
lock release and turn the
release mode dial to E.
3Frame the photograph and focus.
In single-servo autofocus (097),
photographs can only be taken if the
in-focus (I) indicator appears in the viewfinder.
A Close the Viewfinder Eyepiece Shutter
When taking photos without your eye to
the viewfinder, close the viewfinder
eyepiece shutter to prevent light entering
via the viewfinder from appearing in
photographs or interfering with exposure.
Release mode dial
115
k
4Start the timer.
Press the shutter-release
button all the way down to
start the timer.
The self-timer
lamp will start to flash. Two seconds before the photograph is
taken, the self-timer lamp will stop flashing.
The shutter will
be released about ten seconds after the timer starts.
To turn the self-timer off before a photograph is taken, turn the
release mode dial to another setting.
AA
Time (bulb) exposures can not be recorded using the self-timer. A fixed
shutter speed will be used if a speed of A is selected in exposure
mode h.
ASee Also
For information on choosing the duration of the self-timer, the number
of shots taken, and the interval between shots, see Custom Setting c3
(Self-timer, 0317). For information on setting a beep to sound during
the timer count-down, see Custom Setting d1 (Beep, 0318).
116
k
Mirror up Mode
Choose this mode to minimize blurring caused by camera
movement when the mirror is raised. Use of a tripod is
recommended.
1Select mirror up mode.
Press the release mode dial
lock release and turn the
release mode dial to MUP.
2Raise the mirror.
Frame the picture, focus, and then press
the shutter-release button the rest of the
way down to raise the mirror.
3Take a picture.
Press the shutter-release button all the
way down again to take a picture. To
prevent blurring caused by camera
movement, press the shutter-release button smoothly, or use
an optional remote cord (0394). The mirror lowers when
shooting ends.
DMirror Up
While the mirror is raised, photos can not be framed in the
viewfinder and autofocus and metering will not be performed.
AMirror up Mode
A picture will be taken automatically if no operations are performed for
about 30 s after the mirror is raised.
Release mode dial
S
117
S
ISO Sensitivity
“ISO sensitivity” is the digital equivalent of film speed. Choose
from settings that range from ISO 100 and ISO 12800 in steps
equivalent to 1/3 EV. Settings of from about 0.3 to 1 EV below ISO
100 and 0.3 to 4 EV above ISO 12800 are also available for special
situations. The higher the ISO sensitivity, the less light needed to
make an exposure, allowing higher shutter speeds or smaller
apertures.
ISO sensitivity can be adjusted
by pressing the S button and
rotating the main command
dial until the desired setting is
displayed in the control panels
or viewfinder.
Manual Adjustment
S button Main command
dial
Top control panel Rear control panel Viewfinder
118
S
AThe ISO Sensitivity Menu
ISO sensitivity can also be adjusted using the ISO
sensitivity settings option in the shooting
menu (0293).
AHi 0.3–Hi 4
The settings Hi 0.3 through Hi 4 correspond to ISO sensitivities 0.3–4 EV
over ISO 12800 (ISO16000–204800 equivalent). Pictures taken at these
settings are more likely to be subject to noise (randomly-spaced bright
pixels, fog, or lines).
ALo 0.3–Lo 1
The settings Lo 0.3 through Lo 1 correspond to ISO sensitivities
0.3–1 EV below ISO 100 (ISO 80–50 equivalent).
Use for larger apertures
when lighting is bright. Contrast is slightly higher than normal; in most
cases, ISO sensitivities of ISO 100 or above are recommended.
ASee Also
For information on choosing the ISO sensitivity step size, see Custom
Setting b1 (ISO sensitivity step value; 0313). For information on
using the High ISO NR option in the shooting menu to reduce noise at
high ISO sensitivities, see page 302.
119
S
Auto ISO Sensitivity Control
If On is selected for ISO sensitivity settings > Auto ISO
sensitivity control in the shooting menu, ISO sensitivity will
automatically be adjusted if optimal exposure can not be achieved
at the value selected by the user (ISO sensitivity is adjusted
appropriately when the flash is used).
1Select Auto ISO
sensitivity control for
ISO sensitivity settings
in the shooting menu.
To display the menus, press
the G button.
Select ISO
sensitivity settings in the shooting menu, highlight Auto ISO
sensitivity control, and press 2.
2Select On.
Highlight On and press J
(if Off is selected, ISO
sensitivity will remain fixed
at the value selected by the
user).
G button
J button
120
S
3Adjust settings.
The maximum value for auto
ISO sensitivity can be selected
using Maximum sensitivity
(the minimum value for auto
ISO sensitivity is automatically set to ISO 100; note that if the
value selected for Maximum sensitivity is lower than the
value currently selected for ISO sensitivity, the value selected
for Maximum sensitivity will be used). In exposure modes e
and g, sensitivity will only be adjusted if underexposure would
result at the shutter speed selected for Minimum shutter
speed (1/4000–1 s, or Auto; in modes f and h, ISO sensitivity
will be adjusted for optimal exposure at the shutter speed
selected by the user). If Auto (available only with CPU lenses;
equivalent to 1/30 s when a non-CPU lens is used) is selected,
the camera will choose the minimum shutter speed based on
the focal length of the lens (auto shutter-speed selection can
be fine-tuned by highlighting Auto and pressing 2; for
example, even faster values than those usually selected
automatically by the camera can be used with telephoto
lenses to reduce blur).
Shutter speeds slower than the
minimum value may be used if optimum exposure can not be
achieved at the ISO sensitivity value selected for Maximum
sensitivity.
Press J to exit when settings are complete.
When On is selected, the viewfinder and
rear control panel show Z. When
sensitivity is altered from the value selected
by the user, these indicators flash and the
altered value is shown in the viewfinder and rear control panel.
121
S
ATurning Auto ISO Sensitivity Control On or Off
You can turn auto ISO sensitivity control on or
off by pressing the S button and rotating the
sub-command dial. The rear control panel
displays an Z icon when auto ISO
sensitivity control is on and Y when it is off.
AAuto ISO Sensitivity Control
Noise (randomly-spaced bright pixels, fog, or lines) is more likely at
higher sensitivities. Use the High ISO NR option in the shooting menu
to reduce noise (see page 302). When a flash is used, the value selected
for Minimum shutter speed is ignored in favor of the option selected
for Custom Setting e1 (Flash sync speed, 0323). Note that ISO
sensitivity may be raised automatically when auto ISO sensitivity
control is used in combination with slow sync flash modes (available
with optional flash units; 0192), possibly preventing the camera from
selecting slow shutter speeds.
122
S
V
123
Z
Exposure
Metering determines how the camera sets exposure.
The
following options are available:
Metering
Option Description
L
Matrix: Produces natural results in most situations.
Camera meters
a wide area of the frame and set exposure according to tone
distribution, color, composition, and, with type G or D lenses
(0385), distance information (3D color matrix metering III; with
other CPU lenses, camera uses color matrix metering III, which
does not include 3D distance information).
With non-CPU lenses,
camera uses color matrix metering if focal length and maximum
aperture are specified using Non-CPU lens data option in setup
menu (0228); otherwise camera uses center-weighted metering.
M
Center-weighted: Camera meters entire frame but assigns greatest
weight to center area (if CPU lens is attached, size of area can be
selected using Custom Setting b5, Center-weighted area, 0315;
if non-CPU lens is attached, area is 12 mm in diameter).
Classic
meter for portraits; recommended when using filters with an
exposure factor (filter factor) over 1×.*
N
Spot: Camera meters circle 4 mm (0.16 in.) in diameter
(approximately 1.5% of frame).
Circle is centered on current focus
point, making it possible to meter off-center subjects (if non-CPU
lens is used or if auto-area AF is in effect, camera will meter center
focus point).
Ensures that subject will be correctly exposed, even
when background is much brighter or darker. *
* For improved precision with non-CPU lenses, specify lens focal length and
maximum aperture in Non-CPU lens data menu (0228).
124
Z
To choose a metering
option, press the Y
button and rotate the
main command dial
until the desired
setting is displayed in
the viewfinder and
top control panel.
ASee Also
For information on making separate adjustments to optimal exposure
for each metering method, see Custom Setting b6 (Fine-tune optimal
exposure, 0315).
Y button Main command dial
Top control panel Viewfinder
125
Z
Exposure Mode
To determine how the
camera sets shutter speed
and aperture when
adjusting exposure, press
the I (Q) button and
rotate the main command
dial until the desired option
appears in the top control
panel.
ALens Types
When using a CPU lens equipped with an aperture ring (0387), lock
the aperture ring at the minimum aperture (highest f-number).
Type G
lenses are not equipped with an aperture ring.
Non-CPU lenses can only be used in exposure mode g (aperture-priority
auto) and h (manual).
In other modes, exposure mode g is
automatically selected when a non-CPU lens is attached (0388).
The
exposure mode indicator (e or f) will flash in the top control panel and
g will be displayed in the viewfinder.
ADepth-of-Field Preview
To preview the effects of aperture, press and
hold the Pv button.
The lens will be stopped
down to the aperture value selected by the
camera (modes e and f) or the value chosen by
the user (modes g and h), allowing depth of field
to be previewed in the viewfinder.
ACustom Setting e5—Modeling Flash
This setting controls whether optional flash units such as the SB-910,
SB-900, SB-800, SB-700, and SB-600 (0194) will emit a modeling flash
when the Pv button is pressed.
See page 325 for more information.
I (Q) button
Main command dial
Pv button
126
Z
e: Programmed Auto
In this mode, the camera automatically adjusts shutter speed and
aperture according to a built-in program to ensure optimal
exposure in most situations.
This mode is recommended for
snapshots and other situations in which you want to leave the
camera in charge of shutter speed and aperture.
AFlexible Program
In exposure mode e, different combinations of
shutter speed and aperture can be selected by
rotating the main command dial while the
exposure meters are on (“flexible program”).
Rotate the dial to the right for large apertures
(low f-numbers) that blur background details or
fast shutter speeds that “freeze” motion.
Rotate
the dial to the left for small apertures (high f-
numbers) that increase depth of field or slow
shutter speeds that blur motion.
All
combinations produce the same exposure.
While flexible program is in effect, an asterisk
(“U”) appears in the top control panel.
To
restore default shutter speed and aperture settings, rotate the dial until
the asterisk is no longer displayed, choose another mode, or turn the
camera off.
ASee Also
See page 418 for information on the built-in exposure program.
For
information on activating the exposure meters, see “The Standby
Timer” on page 45.
Main command dial
127
Z
f: Shutter-Priority Auto
In shutter-priority auto, you choose the shutter speed while the
camera automatically selects the aperture that will produce the
optimal exposure.
Use slow shutter speeds to suggest motion by
blurring moving objects, fast shutter speeds to “freeze” motion.
To choose a shutter speed,
rotate the main command
dial while the exposure
meters are on.
Shutter speed
can be set to “p” or to
values between 30 s and
1/8,000 s.
Shutter speed can be
locked at the selected setting
(0133).
Fast shutter speed (1/1,600 s) Slow shutter speed (1/6 s)
Main command dial
128
Z
g: Aperture-Priority Auto
In aperture-priority auto, you choose the aperture while the camera
automatically selects the shutter speed that will produce the
optimal exposure.
Large apertures (low f-numbers) increase flash
range (0192) and reduce depth of field, blurring objects behind
and in front of the main subject.
Small apertures (high f-numbers)
increase depth of field, bringing out details in the background and
foreground.
Short field depths are generally used in portraits to
blur background details, long field depths in landscape
photographs to bring the foreground and background into focus.
To choose an aperture
between the minimum and
maximum values for the lens,
rotate the sub-command dial
while the exposure meters are
on.
Aperture can be locked at
the selected setting (0133).
Small aperture (f/36) Large aperture (f/2.8)
ANon-CPU Lenses (0385, 388)
Use the lens aperture ring to adjust aperture.
If the maximum aperture of the lens has been
specified using the Non-CPU lens data item
in setup menu (0229) when a non-CPU lens is
attached, the current f-number will be
displayed in the viewfinder and top control
panel, rounded to the nearest full stop.
Otherwise the aperture displays will show only the number of stops
(F, with maximum aperture displayed as FA) and the f-number must
be read from the lens aperture ring.
Sub-command dial
129
Z
h: Manual
In manual exposure mode, you control both shutter speed and
aperture. While the exposure meters are on, rotate the main
command dial to choose a shutter speed, and the sub-command
dial to set aperture.
Shutter speed can be set to “p” or to
values between 30 s and 1/8,000 s, or the shutter can be held open
indefinitely for a long time-exposure (A, 0131).
Aperture
can be set to values between the minimum and maximum values
for the lens.
Use the exposure indicators to check exposure.
Shutter speed and aperture can be locked at the selected setting
(0133).
Sub-command dial
Main command dial
Aperture
Shutter
speed
130
Z
AAF Micro NIKKOR Lenses
Provided that an external exposure meter is used, the exposure ratio need
only be taken into account when the lens aperture ring is used to set
aperture.
AExposure Indicators
The exposure indicators in the viewfinder and top control panel show
whether the photograph would be under- or over-exposed at current
settings. Depending on the option chosen for Custom Setting b2 (EV
steps for exposure cntrl, 0313), the amount of under- or over-
exposure is shown in increments of 1/3EV, 1/2EV, or 1 EV. If the limits of
the exposure metering system are exceeded during viewfinder
photography or live view, the exposure indicators and the shutter speed
(modes e and g) and/or aperture (modes e and f) displays will flash.
Custom Setting b2 set to 1/3 step
Optimal exposure Underexposed by 1/3EV Overexposed by over 3 EV
Top control
panel
Viewfinder
ASee Also
For information reversing the exposure indicators so that negative
values are displayed on the right and positive values on the left, see
Custom Setting f13 (Reverse indicators, 0338).
131
Z
Long Time-Exposures
At a shutter speed of A, the shutter will remain open while the
shutter-release button is held down.
Use for long time-exposure
photographs of moving lights, the stars, night scenery, or
fireworks.
A tripod and optional remote cord (0394) are
recommended to prevent blur.
1Ready the camera.
Mount the camera on a tripod or place it on a stable, level
surface.
If you are using an optional remote cord, attach it to
the camera.
Shutter speed: 35 s; aperture: f/25
ALong Time-Exposures
Close the viewfinder eyepiece shutter to prevent light entering via
the viewfinder from appearing in the photograph or interfering
with exposure (0114).
Nikon recommends using a fully charged
EN-EL18 battery or an optional EH-6b AC adapter and EP-6 power
connector to prevent loss of power while the shutter is open.
Note
that noise (bright spots, randomly-spaced bright pixels or fog) may
be present in long exposures; before shooting, choose On for the
Long exposure NR option in the shooting menu (0302).
132
Z
2Select exposure
mode h.
Press the I (Q)
button and rotate the
main command dial
until h is displayed in
the top control panel.
3Choose a shutter speed.
While the exposure meters are on, rotate
the main command dial until “A”
appears in the shutter-speed displays.
The exposure indicators do not appear when “A“ is
selected.
4Press the shutter-release button all the way down.
Press the shutter-release button on the camera or remote cord
all the way down.
The shutter will remain open while the
shutter-release button is pressed.
5Release the shutter-release button.
Remove your finger from the shutter-release button to record
the photograph.
I (Q) button
Main command dial
133
Z
Shutter-Speed and Aperture Lock
Shutter speed lock is available in shutter-priority auto and manual
exposure modes, aperture lock in aperture-priority auto and
manual exposure modes.
Shutter speed and aperture lock are not
available in programmed auto exposure mode.
1Assign shutter speed and aperture lock to a camera
control.
Select Shutter spd & aperture lock as the “Press + command
dials” option in the Custom Settings menu (0332). Shutter
speed and aperture lock can be assigned to the Fn button
(Custom Setting f3, Assign Fn button, 0328), the Pv button
(Custom Setting f4, Assign preview button, 0333), or the
center of the sub-selector (Custom Setting f6, Assign sub-
selector center, 0333).
2Lock shutter speed and/or aperture.
Shutter speed (exposure modes f and h): Press the selected control
and rotate the main command dial until F icons appear in the
viewfinder and top control panel.
To unlock shutter speed, press the control and rotate the main
command dial until the F icons disappear from the displays.
Fn button Main command dial
134
Z
Aperture (exposure modes g and h): Press the selected control and
rotate the sub-command dial until F icons appear in the
viewfinder and the top control panel.
To unlock aperture, press the control and rotate the sub-
command dial until the F icons disappear from the displays.
ASee Also
Use Custom Setting f8 (Shutter spd & aperture lock; 0334) to keep
shutter speed and/or aperture locked at the selected values.
Fn button Sub-command dial
135
Z
Autoexposure (AE) Lock
Use autoexposure lock to recompose photographs after using
center-weighted metering and spot metering to meter exposure.
Note that matrix metering will not produce the desired results.
1Lock exposure.
Position the subject in the selected
focus point and press the shutter-
release button halfway.
With the
shutter-release button pressed halfway
and the subject positioned in the focus
point, press the center of the sub-
selector to lock exposure (if you are
using autofocus, confirm that the I in-
focus indicator appears in the
viewfinder).
While exposure lock is in effect, an AE-L
indicator will appear in the viewfinder.
2Recompose the
photograph.
Keeping the center of the sub-
selector pressed, recompose
the photograph and shoot.
Shutter-release
button
Center of sub-
selector
136
Z
AMetered Area
In spot metering, exposure will be locked at the value metered in a
4-mm (0.16 in.) circle centered on the selected focus point.
In center-
weighted metering, exposure will be locked at the value metered in a
12-mm circle in the center of the viewfinder.
AAdjusting Shutter Speed and Aperture
While exposure lock is in effect, the following settings can be changed
without altering the metered value for exposure:
Exposure mode Setting
eShutter speed and aperture (flexible program; 0126)
fShutter speed
gAperture
The new values can be confirmed in the viewfinder and top control
panel.
Note that the metering method can not be changed while
exposure lock is in effect.
ASee Also
If On is selected for Custom Setting c1 (Shutter-release button AE-L,
0316), exposure will lock when the shutter-release button is pressed
halfway.
For information on changing the role of the center of the sub-
selector, see Custom Setting f6 (Assign sub-selector center, 0333).
137
Z
Exposure Compensation
Exposure compensation is used to alter exposure from the value
suggested by the camera, making pictures brighter or darker.
It is
most effective when used with center-weighted or spot metering
(0123). Choose from values between –5 EV (underexposure) and
+5 EV (overexposure) in increments of 1/3 EV.
In general, positive
values make the subject brighter while negative values make it
darker.
To choose a value for
exposure compensation,
press the E button and
rotate the main
command dial until the
desired value is
displayed in the
viewfinder or top control
panel.
–1 EV No exposure
compensation
+1 EV
±0 EV
(E button pressed)
–0.3 EV +2.0 EV
E button
Main command dial
138
Z
At values other than ±0.0, the 0 at the
center of the exposure indicators will
flash (exposure modes e, f, and g only)
and a E icon will be displayed in the
viewfinder and top control panel after
you release the E button.
The current
value for exposure compensation can be confirmed in the
exposure indicator by pressing the E button.
Normal exposure can be restored by setting exposure
compensation to ±0.0.
Exposure compensation is not reset when
the camera is turned off.
AExposure Mode h
In exposure mode h, exposure compensation affects only the exposure
indicator; shutter speed and aperture do not change.
AUsing a Flash
When a flash is used, exposure compensation affects both flash level
and exposure, altering the brightness of both the main subject and the
background.
Custom Setting e4 (Exposure comp. for flash, 0325) can
be used to restrict the effects of exposure compensation to the
background only.
ASee Also
For information on choosing the size of the increments available for
exposure compensation, see Custom Setting b3 (Exp./flash comp. step
value, 0313).
For information on making adjustments to exposure
compensation without pressing the E button, see Custom Setting b4
(Easy exposure compensation, 0314).
For information on
automatically varying exposure, flash level, white balance, or Active
D-Lighting, see page 139.
139
Z
Bracketing
Bracketing automatically varies exposure, flash level, Active
D-Lighting (ADL), or white balance slightly with each shot,
“bracketing” the current value.
Choose in situations in which it is
difficult to set exposure, flash level (i-TTL and, where supported,
auto aperture flash control modes only; see pages 193 and 198),
Active D-Lighting, or white balance and there is not time to check
results and adjust settings with each shot, or to experiment with
different settings for the same subject.
❚❚ Exposure and Flash Bracketing
To vary exposure and/or flash level over a series of photographs:
Exposure modified by:
0 EV
Exposure modified by:
–1 EV
Exposure modified by:
+1 EV
140
Z
1Select flash or exposure
bracketing for Custom
Setting e6 (Auto
bracketing set) in the
Custom Settings menu.
To display the menus, press
the G button.
Select
Custom Setting e6 (Auto
bracketing set) in the
Custom Settings menu,
highlight an option, and
press J.
Choose AE &
flash to vary both
exposure and flash level, AE only to vary only exposure, or
Flash only to vary only flash level.
G button
J button
141
Z
2Choose the number of shots.
Pressing the D button, rotate the main command dial to
choose the number of shots in the bracketing sequence.
The
number of shots is shown in the top control panel.
At settings other than zero, a M icon and exposure and
flash bracketing indicator will be displayed in the
viewfinder and top control panel.
D button Main command
dial
Top control panel
Number of shots
Exposure and flash
bracketing indicator
142
Z
3Select an exposure increment.
Pressing the D button, rotate the sub-command dial to
choose the exposure increment.
At default settings, the size of the increment can be chosen
from 1/3, 2/3, and 1 EV.
The bracketing programs with an
increment of 1/3EV are listed below.
Control panel display No. of shots Bracketing order (EVs)
00
3 0/+0.3/+0.7
3 0/–0.7/–0.3
20/+0.3
20/–0.3
3 0/–0.3/+0.3
5 0/–0.7/–0.3/+0.3/+0.7
70/–1.0/–0.7/–0.3/+0.3/
+0.7/+1.0
90/–1.3/–1.0/–0.7/–0.3/
+0.3/+0.7/+1.0/+1.3
ASee Also
For information on choosing the size of the exposure increment, see
Custom Setting b2 (EV steps for exposure cntrl, 0313).
For
information on choosing the order in which bracketing is performed,
see Custom Setting e8 (Bracketing order, 0326).
For information on
choosing the role of the D button, see Custom Setting f9 (Assign BKT
button, 0335).
D button Sub-command
dial
Top control panel
Exposure increment
143
Z
4Frame a photograph, focus, and
shoot.
The camera will vary exposure and/or flash level shot-by-shot
according to the bracketing program selected.
Modifications
to exposure are added to those made with exposure
compensation (see page 137), making it possible to achieve
exposure compensation values of more than 5 EV.
While bracketing is in effect, a bracketing progress indicator
will be displayed in the viewfinder and top control panel.
A
segment will disappear from the indicator after each shot.
❚❚ Canceling Bracketing
To cancel bracketing, press the D button and rotate the main
command dial until the number of shots in the bracketing
sequence is zero ( ) and M is no longer displayed.
The program
last in effect will be restored the next time bracketing is activated.
Bracketing can also be cancelled by performing a two-button reset
(0207), although in this case the bracketing program will not be
restored the next time bracketing is activated.
No. shots: 3; increment: 0.7 Display after first shot
144
Z
AExposure and Flash Bracketing
In continuous low speed and continuous high speed modes, shooting
will pause after the number of shots specified in the bracketing
program have been taken.
Shooting will resume the next time the
shutter-release button is pressed.
In self-timer mode, the camera will
take the number of shots selected in Step 2 on page 141 each time the
shutter-release button is pressed, regardless of the option selected for
Custom Setting c3 (Self-timer)>Number of shots (0317); the interval
between shots is however controlled by Custom Setting c3 (Self-
timer)>Interval between shots.
In other modes, one shot will be
taken each time the shutter-release button is pressed.
If the memory card fills before all shots in the sequence have been
taken, shooting can be resumed from the next shot in the sequence
after the memory card has been replaced or shots have been deleted to
make room on the memory card.
If the camera is turned off before all
shots in the sequence have been taken, bracketing will resume from the
next shot in the sequence when the camera is turned on.
AExposure Bracketing
The camera modifies exposure by varying shutter speed and aperture
(programmed auto), aperture (shutter-priority auto), or shutter speed
(aperture-priority auto, manual exposure mode).
If On is selected for
ISO sensitivity settings > Auto ISO sensitivity control (0119) in
modes e, f, and g and no flash is attached, the camera will modify
exposure by varying ISO sensitivity and only vary shutter speed and/or
aperture if the limits of exposure system are exceeded.
Custom Setting
e7 (Auto bracketing (mode M), 0326) can be used to change how the
camera performs exposure and flash bracketing in manual exposure
mode.
Bracketing can be performed by varying flash level together
with shutter speed and/or aperture, or by varying flash level alone.
145
Z
❚❚ White Balance Bracketing
The camera creates multiple copies of each photograph, each with
a different white balance.
For more information on white balance,
see page 153.
1Select white balance bracketing.
Choose WB bracketing for Custom
Setting e6 Auto bracketing set.
2Choose the number of shots.
Pressing the D button, rotate the main command dial to
choose the number of shots in the bracketing sequence.
The
number of shots is shown in the top control panel.
At settings other than zero, a W icon and WB
bracketing indicator will appear in the top control
panel and M will be displayed in the viewfinder.
Number of shots
Top control panel
WB bracketing
indicator
D button Main command
dial
146
Z
3Select a white balance increment.
Pressing the D button, rotate the sub-command dial to
choose the white balance adjustment.
Each increment is
roughly equivalent to 5 mired.
Choose from increments of 1 (5 mired), 2 (10 mired), or 3
(15 mired).
Higher B values correspond to increased amounts
of blue, higher A values to increased amounts of amber
(0157).
The bracketing programs with an increment of 1 are
listed below.
Control panel display
No. of
shots
White balance
increment Bracketing order (EVs)
01 0
31B 1B/0/2B
31A 1A/2A/0
21B 0/1B
21A 0/1A
3 1A, 1B 0/1A/1B
5 1A, 1B 0/2A/1A/1B/2B
71A, 1B0/3A/2A/1A/
1B/2B/3B
91A, 1B
0/4A/3A/2A/1A/
1B/2B/3B/4B
ASee Also
See page 158 for a definition of “mired.”
W
h
ite
b
a
l
ance
increment
D button Sub-command
dial
Top control panel
147
Z
4Frame a photograph, focus, and
shoot.
Each shot will be processed to create the number of copies
specified in the bracketing program, and each copy will have a
different white balance.
Modifications to white balance are
added to the white balance adjustment made with white
balance fine-tuning.
If the number of shots in the
bracketing program is greater than
the number of exposures remaining,
n and the icon for the affected
card will flash in the top control panel,
a flashing j icon will appear in the
viewfinder as shown at right, and the
shutter release will be disabled.
Shooting can begin when a new memory card is inserted.
148
Z
❚❚ Canceling Bracketing
To cancel bracketing, press the D button and rotate the main
command dial until the number of shots in the bracketing
sequence is zero (r) and W is no longer displayed.
The
program last in effect will be restored the next time bracketing is
activated.
Bracketing can also be cancelled by performing a two-
button reset (0207), although in this case the bracketing
program will not be restored the next time bracketing is activated.
AWhite Balance Bracketing
White balance bracketing is not available at an image quality of NEF
(RAW).
Selecting NEF (RAW), NEF (RAW)+JPEG fine, NEF (RAW)+JPEG
normal, or NEF (RAW)+JPEG basic cancels white balance bracketing.
White balance bracketing affects only color temperature (the amber-
blue axis in the white balance fine-tuning display, 0157).
No
adjustments are made on the green-magenta axis.
In self-timer mode, the number of copies specified in the white-balance
program will be created each time the shutter is released, regardless of
the option selected for Custom Setting c3 (Self-timer) > Number of
shots (0317).
If the camera is turned off while the memory card access lamp is lit, the
camera will power off only after all photographs in the sequence have
been recorded.
149
Z
❚❚ ADL Bracketing
The camera varies Active D-Lighting over a series of exposures.
For
more information on Active D-Lighting, see page 184.
1Select ADL bracketing.
Choose ADL bracketing for Custom
Setting e6 Auto bracketing set.
2Choose the number of shots.
Pressing the D button, rotate the main command dial to
choose the number of shots in the bracketing sequence.
The
number of shots is shown in the top control panel.
At settings other than zero, a d icon and an ADL bracketing
indicator appear in the top control panel and M will be
displayed in the viewfinder.
Choose two shots to take one
photograph with Active D-Lighting off and another at a
selected value.
Choose three to five shots to take a series of
photographs with Active D-Lighting set successively to values
between Off and Normal (three shots), between Off and High
(four shots), or between Off and Extra high 1 or Low and
Extra high 2 (five shots). If you choose more than two shots,
proceed to Step 4.
Number of shots
Top control panel
ADL bracketing
indicator
D button Main command
dial
150
Z
3Select Active D-Lighting.
Pressing the D button, rotate the sub-command dial to
choose Active D-Lighting.
Active D-Lighting is shown in the top control panel.
D button Sub-command
dial
Control panel display ADL
Y
Auto
R
Low
Q
Normal
Control panel display ADL
P
High
Z
Extra high 1
3
Extra high 2
151
Z
4Frame a photograph, focus, and
shoot.
The camera will vary Active D-Lighting shot-by-shot according
to the bracketing program selected.
While bracketing is in
effect, a bracketing progress indicator will be displayed in the
top control panel.
A segment will disappear from the
indicator after each shot.
152
Z
❚❚ Canceling Bracketing
To cancel bracketing, press the D button and rotate the main
command dial until the number of shots in the bracketing
sequence is zero (r) and d is no longer displayed.
The
program last in effect will be restored the next time bracketing is
activated.
Bracketing can also be cancelled by performing a two-
button reset (0207), although in this case the bracketing
program will not be restored the next time bracketing is activated.
AADL Bracketing
In continuous low speed and continuous high speed modes, shooting
will pause after the number of shots specified in the bracketing
program have been taken.
Shooting will resume the next time the
shutter-release button is pressed.
In self-timer mode, the camera will
take the number of shots selected in Step 2 on page 149 each time the
shutter-release button is pressed, regardless of the option selected for
Custom Setting c3 (Self-timer)>Number of shots (0317); the interval
between shots is however controlled by Custom Setting c3 (Self-
timer)>Interval between shots.
In other modes, one shot will be
taken each time the shutter-release button is pressed.
If the memory card fills before all shots in the sequence have been
taken, shooting can be resumed from the next shot in the sequence
after the memory card has been replaced or shots have been deleted to
make room on the memory card.
If the camera is turned off before all
shots in the sequence have been taken, bracketing will resume from the
next shot in the sequence when the camera is turned on.
r
153
r
White Balance
White balance ensures that colors are unaffected by the color of
the light source.
Auto white balance is recommended with most
light sources.
If the desired results can not be achieved with auto
white balance, choose an option from the list below or use preset
white balance.
White Balance Options
Option Color temp. * Description
vAuto
3,500–
8,000 K
White balance is adjusted
automatically. For best results, use type
G or D lens. If optional flash fires, results
are adjusted appropriately.
Normal
Keep warm lighting
colors
JIncandescent 3,000 K Use under incandescent lighting.
IFluorescent Use with:
Sodium-vapor lamps 2,700 K • Sodium-vapor lighting (found in
sports venues).
Warm-white
fluorescent 3,000 K • Warm-white fluorescent lights.
White fluorescent 3,700 K • White fluorescent lights.
Cool-white
fluorescent 4,200 K • Cool-white fluorescent lights.
Day white
fluorescent 5,000 K • Daylight white fluorescent lights.
Daylight fluorescent 6,500 K • Daylight fluorescent lights.
High temp.
mercury-vapor 7,200 K • High color temperature light sources
(e.g. mercury-vapor lamps).
HDirect sunlight 5,200 K Use with subjects lit by direct sunlight.
NFlash 5,400 K Use with optional flash units.
154
r
White balance can be selected by pressing the U button and
rotating the main command dial until the desired setting is
displayed in the rear control panel.
GCloudy 6,000 K Use in daylight under overcast skies.
MShade 8,000 K Use in daylight with subjects in the shade.
KChoose color temp. 2,500–
10,000 K
Choose color temperature from list of
values (0160).
LPreset manual —
Use subject, light source, or existing
photograph as reference for white
balance (0163).
* All values are approximate and do not reflect fine-tuning (if applicable).
Rear control panel
U button Main command dial
AThe Shooting Menu
White balance can also be adjusted using the
White balance option in the shooting menu
(0293), which also can be used to fine-tune
white balance (0156) or measure a value for
preset white balance (0165).
The Auto option
in the White balance menu offers a choice of
Normal and Keep warm lighting colors, which
preserves the warm colors produced by incandescent lighting, while
the IFluorescent option can be used to select the light source from
the bulb types.
Option Color temp. * Description
155
r
AStudio Flash Lighting
Auto white balance may not produce the desired results with large
studio flash units.
Use preset white balance or set white balance to
Flash and use fine-tuning to adjust white balance.
ASee Also
When WB bracketing is selected for Custom Setting e6 (Auto
bracketing set, 0325), the camera will create several images each
time the shutter is released.
White balance will be varied with each
image, “bracketing” the value currently selected for white balance.
See
page 145 for more information.
AColor Temperature
The perceived color of a light source varies with the viewer and other
conditions.
Color temperature is an objective measure of the color of a
light source, defined with reference to the temperature to which an
object would have to be heated to radiate light in the same
wavelengths.
While light sources with a color temperature in the
neighborhood of 5,000–5,500 K appear white, light sources with a lower
color temperature, such as incandescent light bulbs, appear slightly
yellow or red.
Light sources with a higher color temperature appear
tinged with blue.
The camera white balance options are adapted to the
following color temperatures:
•I (sodium-vapor lamps): 2,700 K
•J (incandescent)/
I(warm-white fluorescent.):
3,000 K
•I (white fluorescent): 3,700 K
•I (cool-white fluorescent):
4,200 K
•I (day white fluorescent):
5,000 K
•H (direct sunlight): 5,200 K
•N (flash): 5,400 K
•G (cloudy): 6,000 K
•I (daylight fluorescent): 6,500 K
•I (high temp. mercury-vapor):
7,200 K
•M (shade): 8,000 K
156
r
Fine-Tuning White Balance
White balance can be “fine-tuned” to compensate for variations in
the color of the light source or to introduce a deliberate color cast
into an image.
White balance is fine-tuned using the White
balance option in the shooting menu or by pressing the U
button and rotating the sub-command dial.
❚❚ The White Balance Menu
1Select a white balance
option in the shooting
menu.
To display the menus, press
the G button.
Select
White balance in the
shooting menu, then highlight a white balance option and
press 2.
If an option other than Auto, Fluorescent, Choose
color temp., or Preset manual is selected, proceed to Step 2.
If Auto or Fluorescent is selected, highlight a lighting type
and press 2.
For information on fine-tuning preset white
balance, see page 169.
G button
157
r
2Fine-tune white balance.
Use the multi selector to fine-
tune white balance.
White
balance can be fine-tuned on
the amber (A)–blue (B) axis and
the green (G)–magenta (M)
axis.
The horizontal (amber-
blue) axis corresponds to color temperature, with each
increment equivalent to about 5 mired.
The vertical (green-
magenta) axis has the similar effects to the corresponding
color compensation (CC) filters.
3Press J.
Press J to save settings and return to the
shooting menu. If white balance has been
fine-tuned, an asterisk (“U”) will be
displayed in the rear control panel.
Coordinates
Adjustment
Increase green
Increase magenta
Increase blue Increase amber
Green (G)
Magenta (M)
Blue (B) Amber (A)
J button
158
r
AWhite Balance Fine-Tuning
The colors on the fine-tuning axes are relative, not absolute. For
example, moving the cursor to B (blue) when a “warm” setting such as
J (Incandescent) is selected for white balance will make photographs
slightly “colder” but will not actually make them blue.
A“Mired”
Any given change in color temperature produces a greater difference in
color at low color temperatures than it would at higher color
temperatures.
For example, a change of 1000 K produces a much
greater change in color at 3000 K than at 6000 K.
Mired, calculated by
multiplying the inverse of the color temperature by 10 6, is a measure of
color temperature that takes such variation into account, and as such is
the unit used in color-temperature compensation filters.
E.g.:
• 4000 K–3000 K (a difference of 1000 K)=83 mired
• 7000 K–6000 K (a difference of 1000 K)=24 mired
159
r
❚❚ The U Button
At settings other than K (Choose color temp.) and L (Preset
manual), the U button can be used to fine-tune white balance
on the amber (A)–blue (B) axis (0157; to fine-tune white balance
when L is selected, use the shooting menu as described on
page 156).
Six settings in both directions are available; each
increment is equivalent to about 5 mired (0158).
Press the U
button and rotate the sub-command dial until the desired value is
displayed in the rear control panel.
Rotating the sub-command
dial to the left increases the amount of amber (A).
Rotating the
sub-command dial to the right increases the amount of blue (B).
At settings other than 0, an asterisk (“U”) appears in the rear
control panel.
Rear control panel
U button Sub-command dial
160
r
Choosing a Color Temperature
When K (Choose color temp.) is selected for white balance, color
temperature can be selected using the White balance option in
the shooting menu or by using the U button, multi selector, and
sub-command dial.
❚❚ The White Balance Menu
Enter values for the amber-blue and green-magenta axes (0157).
1Select Choose color
temp.
Press the G button and
select White balance in
the shooting menu.
Highlight Choose color
temp. and press 2.
2Select a value for amber-
blue.
Press 4 or 2 to highlight digits
and press 1 or 3 to change.
DChoose Color Temperature
Note that the desired results will not be obtained with flash or
fluorescent lighting.
Choose N (Flash) or I (Fluorescent) for these
sources.
With other light sources, take a test shot to determine if the
selected value is appropriate.
G button
Value for amber (A)-blue
(B) axis
161
r
3Select a value for green-
magenta.
Press 4 or 2 to highlight the G
(green) or M (magenta) axis
and press 1 or 3 to select a
value.
4Press J.
Press J to save changes and return to the
shooting menu.
If a value other than 0 is
selected for the green (G)–magenta (M)
axis, an asterisk (“U”) will be displayed in
the rear control panel.
Value for green (G)-magenta
(M) axis
J button
162
r
❚❚ The U Button
The U button can be used to select the color temperature for the
amber (A)–blue (B) axis only.
Press the U button and rotate the
sub-command dial until the desired value is displayed in the rear
control panel (adjustments are made in mireds; 0158).
To enter a
color temperature directly in increments of 10 K, press the U
button and press 4 or 2 to highlight a digit and press 1 or 3 to
change.
U button Sub-command dial
Rear control panel
163
r
Preset Manual
Preset manual is used to record and recall custom white balance
settings for shooting under mixed lighting or to compensate for
light sources with a strong color cast.
The camera can store up to
four values for preset white balance in presets d-1 through d-4.
Two methods are available for setting preset white balance:
Method Description
Direct measurement
Neutral gray or white object is placed under
lighting that will be used in final photograph and
white balance is measured by camera (0164).
Copy from existing
photograph
White balance is copied from photo on memory
card (0168).
AWhite Balance Presets
Changes to white balance presets apply to all shooting menu banks
(0294).
A confirmation dialog will be displayed if the user attempts to
change a white balance preset created in another shooting menu bank.
AMeasuring Preset White Balance
Preset manual white balance can not be measured during live view
(049, 63), while you are shooting an HDR photograph (0186) or
multiple exposure (0210), or when Record movies is selected for
Custom Setting g4 (Assign shutter button, 0343).
164
r
❚❚ Measuring a Value for White Balance
1Light a reference object.
Place a neutral gray or white object under the lighting that will
be used in the final photograph.
In studio settings, a standard
gray panel can be used as a reference object.
Note that
exposure is automatically increased by 1 EV when measuring
white balance; in exposure mode h, adjust exposure so that
the exposure indicator shows ±0 (0130).
2Set white balance to L (Preset manual).
Press the U button and rotate the main command dial until
L is displayed in the rear control panel.
3Select a preset.
Press the U button and rotate the sub-command dial until
the desired white balance preset (d-1 to d-4) is displayed in
the rear control panel.
Rear control panel
U button Main command dial
Rear control panel
U button Sub-command dial
165
r
4Select direct measurement mode.
Release the U button briefly and then
press the button until the L icon in
the rear control panel starts to flash.
A
flashing D will also appear in the top
control panel and viewfinder.
The
displays will flash for about six seconds.
5Measure white balance.
Before the indicators stop flashing, frame the
reference object so that it fills the viewfinder and
press the shutter-release button all the way down.
The camera
will measure a value for white balance and store it in the
preset selected in Step 3.
No photograph will be recorded;
white balance can be measured accurately even when the
camera is not in focus.
Top control panel
Rear control panel
Viewfinder
166
r
6Check the results.
If the camera was able to measure a
value for white balance, C will flash
in the control panels for about six
seconds, while the viewfinder will show
a flashing a.
If lighting is too dark or too bright, the
camera may be unable to measure
white balance.
A flashing ba will
appear in the control panels and
viewfinder for about six seconds.
Press
the shutter-release button halfway to
return to Step 5 and measure white
balance again.
Top control panel
Rear control panel
Viewfinder
Top control panel
Rear control panel
Viewfinder
167
r
DDirect Measurement Mode
If no operations are performed while the displays are flashing, direct
measurement mode will end in the time selected for Custom Setting c2
(Standby timer, 0316).
AProtected Presets
If the current preset is protected (0171), white balance can not be fine-
tuned, the comment can not be edited, and 3 will flash in the top
control panel and viewfinder (and L in the rear control panel) if you
attempt to measure a new value.
ASelecting a Preset
Selecting Preset manual for the White balance
option in the shooting menu displays the dialog
shown at right; highlight a preset and press J.
If
no value currently exists for the selected preset,
white balance will be set to 5,200 K, the same as
Direct sunlight.
168
r
❚❚ Copying White Balance from a Photograph
Follow the steps below to copy a value for white balance from an
existing photograph to a selected preset.
1Select L (Preset
manual) for White
balance in the
shooting menu.
Press the G button and
select White balance in
the shooting menu. Highlight Preset manual and press 2.
2Select a destination.
Highlight the destination
preset (d-1 to d-4) and press
the center of the multi selector.
3Choose Select image.
Highlight Select image and
press 2.
G button
169
r
4Highlight a source image.
Highlight the source image. To
view the highlighted image full
frame, press and hold the X
button.
To view images in other locations, press
W and select the desired card and folder
(0236).
5Copy white balance.
Press J to copy the white balance value for the
highlighted photograph to the selected preset.
If the highlighted photograph has a comment
(0352), the comment will be copied to the
comment for the selected preset.
AChoosing a White Balance Preset
Press 1 to highlight the current white balance
preset (d-1–d-4) and press 2 to select another
preset.
AFine-Tuning Preset White Balance
The selected preset can be fine-tuned by
selecting Fine-tune and adjusting white balance
as described on page 157.
J button
170
r
❚❚ Entering a Comment
Follow the steps below to enter a descriptive comment of up to
thirty-six characters for a selected white balance preset.
1Select L (Preset manual).
Highlight Preset manual in the
white balance menu (0168)
and press 2.
2Select a preset.
Highlight the desired preset
and press the center of the
multi selector.
3Select Edit comment.
Highlight Edit comment and
press 2.
4Edit the comment.
Edit the comment as described on page
180.
171
r
❚❚ Protecting a White Balance Preset
Follow the steps below to protect the selected white balance
preset.
Protected presets can not be modified and the Fine-tune
and Edit comment options can not be used.
1Select L (Preset manual).
Highlight Preset manual in the
white balance menu (0168)
and press 2.
2Select a preset.
Highlight the desired preset
and press the center of the
multi selector.
3Select Protect.
Highlight Protect and press 2.
4Select On.
Highlight On and press J
to protect the selected
white balance preset.
To
remove protection, select
Off.J button
172
r
J
173
J
Image Enhancement
Nikon’s unique Picture Control system makes it possible to share
image processing settings, including sharpening, contrast,
brightness, saturation, and hue, among compatible devices and
software.
Selecting a Picture Control
The camera offers a choice of preset Picture Controls.
Choose a
Picture Control according to the subject or type of scene.
1Press L (Z/Q).
A list of Picture Controls
will be displayed.
Picture Controls
Option Description
QStandard Standard processing for balanced results.
Recommended for most situations.
RNeutral
Minimal processing for natural results.
Choose for
photographs that will later be extensively
processed or retouched.
SVivid
Pictures are enhanced for a vivid, photoprint effect.
Choose for photographs that emphasize primary
colors.
TMonochrome Take monochrome photographs.
oPortrait Process portraits for skin with natural texture and a
rounded feel.
pLandscape Produces vibrant landscapes and cityscapes.
L (Z/Q) button
174
J
2Select a Picture Control.
Highlight the desired
Picture Control and press
J.
APreset Picture Controls Versus Custom Picture Controls
The Picture Controls supplied with the camera are referred to as preset
Picture Controls.
Custom Picture Controls are created through
modifications to existing Picture Controls using the Manage Picture
Control option in the shooting menu (0179).
Custom Picture Controls
can be saved to a memory card for sharing among other D4 cameras
and compatible software (0182).
AThe Picture Control Indicator
The current Picture Control is shown in the
information display when the R button is
pressed.
Picture Control
indicator
AThe Shooting Menu
Picture Controls can also be selected using the
Set Picture Control option in the shooting
menu (0293).
J button
175
J
Modifying Existing Picture Controls
Existing preset or custom Picture Controls
(0179) can be modified to suit the scene or
the user’s creative intent.
Choose a balanced
combination of settings using Quick adjust,
or make manual adjustments to individual
settings.
1Select a Picture Control.
Highlight the desired Picture
Control in the Picture Control
list (0173) and press 2.
2Adjust settings.
Press 1 or 3 to highlight the
desired setting and press 4 or
2 to choose a value (0176).
Repeat this step until all
settings have been adjusted, or
select Quick adjust to choose a preset combination of
settings.
Default settings can be restored by pressing the O
(Q) button.
3Press J.
AModifications to Original Picture Controls
Picture Controls that have been modified from
default settings are indicated by an asterisk
(“U”) in the Set Picture Control menu.
176
J
❚❚ Picture Control Settings
Option Description
Quick adjust
Choose from options between –2 and +2 to reduce or
exaggerate the effect of the selected Picture Control
(note that this resets all manual adjustments).
For
example, choosing positive values for Vivid makes
pictures more vivid.
Not available with Neutral,
Monochrome, or custom Picture Controls.
Manual adjustments
(all Picture Controls)
Sharpening
Control the sharpness of outlines.
Select A to adjust
sharpening automatically according to the type of
scene, or choose from values between 0 (no
sharpening) and 9 (the higher the value, the greater the
sharpening).
Contrast
Select A to adjust contrast automatically according to
the type of scene, or choose from values between –3
and +3 (choose lower values to prevent highlights in
portrait subjects from being “washed out” in direct
sunlight, higher values to preserve detail in misty
landscapes and other low-contrast subjects).
Brightness Choose –1 for reduced brightness, +1 for enhanced
brightness.
Does not affect exposure.
Manual adjustments
(non-monochrome only)
Saturation
Control the vividness of colors.
Select A to adjust
saturation automatically according to the type of scene,
or choose from values between –3 and +3 (lower values
reduce saturation and higher values increase it).
Hue
Choose negative values (to a minimum of –3) to make
reds more purple, blues more green, and greens more
yellow, positive values (up to +3) to make reds more
orange, greens more blue, and blues more purple.
Manual adjustments
(monochrome only)
Filter
effects
Simulate the effect of color filters on monochrome
photographs.
Choose from OFF, yellow, orange, red,
and green (0177).
Toning
Choose the tint used in monochrome photographs from
B&W (black-and-white), Sepia, Cyanotype (blue-tinted
monochrome), Red, Yel low, Green, Blue Green, Blue,
Purple Blue, Red Purple (0178).
177
J
D“A” (Auto)
Results for auto sharpening, contrast, and
saturation vary with exposure and the position
of the subject in the frame.
Use a type G or D
lens for best results.
The icons for Picture
Controls that use auto contrast and saturation
are displayed in green in the Picture Control
grid, and lines appear parallel to the axes of the
grid.
AThe Picture Control Grid
Pressing the W button in Step 2 on page 175
displays a Picture Control grid showing the
contrast and saturation for the selected Picture
Control in relation to the other Picture Controls
(only contrast is displayed when Monochrome
is selected).
Release the W button to return to
the Picture Control menu.
APrevious Settings
The line under the value display in the Picture
Control setting menu indicates the previous
value for the setting.
Use this as a reference
when adjusting settings.
AFilter Effects (Monochrome Only)
The options in this menu simulate the effect of color filters on
monochrome photographs.
The following filter effects are available:
Option Description
YYellow Enhances contrast.
Can be used to tone down the brightness of
the sky in landscape photographs.
Orange produces more
contrast than yellow, red more contrast than orange.
OOrange
RRed
GGreen Softens skin tones.
Can be used for portraits.
Note that the effects achieved with Filter effects are more pronounced
than those produced by physical glass filters.
178
J
AToning (Monochrome Only)
Pressing 3 when Toning is selected displays
saturation options.
Press 4 or 2 to adjust
saturation.
Saturation control is not available
when B&W (black-and-white) is selected.
ACustom Picture Controls
The options available with custom Picture Controls are the same as
those on which the custom Picture Control was based.
179
J
Creating Custom Picture Controls
The preset Picture Controls supplied with the camera can be
modified and saved as custom Picture Controls.
1Select Manage Picture
Control in the shooting
menu.
To display the menus, press
the G button.
Highlight
Manage Picture Control
in the shooting menu and press 2.
2Select Save/edit.
Highlight Save/edit and press
2.
3Select a Picture Control.
Highlight an existing Picture
Control and press 2, or press J
to proceed to Step 5 to save a
copy of the highlighted Picture
Control without further
modification.
G button
180
J
4Edit the selected Picture Control.
See page 176 for more information.
To
abandon any changes and start over from
default settings, press the O (Q) button.
Press J when settings are complete.
5Select a destination.
Choose a destination for the
custom Picture Control (C-1
through C-9) and press 2.
6Name the Picture
Control.
The text-entry dialog shown
at right will be displayed.
By
default, new Picture
Controls are named by adding a two-digit number (assigned
automatically) to the name of the existing Picture Control; to
use the default name, proceed to Step 7.
To move the cursor
in the name area, hold the W button and press 4 or 2.
To
enter a new letter at the current cursor position, use the multi
selector to highlight the desired character in the keyboard
area and press the center of the multi selector.
To delete the
character at the current cursor position, press the O (Q)
button.
Custom Picture Control names can be up to nineteen
characters long.
Any characters after the nineteenth will be
deleted.
Keyboard
area
Name area
181
J
7Save changes and exit.
Press J to save changes
and exit. The new Picture
Control will appear in the
Picture Control list.
AManage Picture Control > Rename
Custom Picture Controls can be renamed at any
time using the Rename option in the Manage
Picture Control menu.
AManage Picture Control > Delete
The Delete option in the Manage Picture
Control menu can be used to delete selected
custom Picture Controls when they are no
longer needed.
AThe Original Picture Control Icon
The original preset Picture Control on which the
custom Picture Control is based is indicated by
an icon in the top right corner of the edit
display.
Original Picture
Control icon
J button
182
J
Sharing Custom Picture Controls
Custom Picture Controls created using the Picture Control Utility
available with ViewNX 2 or optional software such as Capture NX 2
can be copied to a memory card and loaded into the camera, or
custom Picture Controls created with the camera can be copied to
the memory card to be used in other D4 cameras and compatible
software and then deleted when no longer needed (if two
memory cards are inserted, the card in the primary slot will be
used; 095).
To copy custom Picture Controls to
or from the memory card, or to
delete custom Picture Controls
from the memory card, highlight
Load/Save in the Manage Picture
Control menu and press 2.
The
following options will be displayed:
•Copy to camera: Copy custom Picture Controls from the memory
card to custom Picture Controls C-1 through C-9 on the camera
and name them as desired.
•Delete from card: Delete
selected custom Picture
Controls from the memory
card.
The confirmation
dialog shown at right will be
displayed before a Picture
Control is deleted; to delete
the selected Picture Control, highlight Yes and press J.
•Copy to card: Copy a custom Picture Control (C-1 through C-9) from
the camera to a selected destination (1 through 99) on the
memory card.
J button
183
J
ASaving Custom Picture Controls
Up to 99 custom Picture Controls can be stored on the memory card at
any one time.
The memory card can only be used to store user-created
custom Picture Controls.
The preset Picture Controls supplied with the
camera (0173) can not be copied to the memory card, renamed, or
deleted.
184
J
Preserving Detail in Highlights
and Shadows
Active D-Lighting
Active D-Lighting preserves details in highlights and shadows,
creating photographs with natural contrast.
Use for high contrast
scenes, for example when photographing brightly lit outdoor
scenery through a door or window or taking pictures of shaded
subjects on a sunny day. It is most effective when used with matrix
metering (0123).
Active D-Lighting off Active D-Lighting: YAuto
D“Active D-Lighting” versus “D-Lighting”
The Active D-Lighting option in the shooting menu adjusts exposure
before shooting to optimize the dynamic range, while the D-Lighting
option in the retouch menu optimizes dynamic range in images after
shooting.
185
J
To use Active D-Lighting:
1Select Active
D-Lighting in the
shooting menu.
To display the menus, press
the G button.
Highlight
Active D-Lighting in the
shooting menu and press
2.
2Choose an option.
Highlight the desired
option and press J.
If
YAuto is selected, the
camera will automatically
adjust Active D-Lighting
according to shooting
conditions (in exposure mode h, however, YAuto is
equivalent to QNormal).
DActive D-Lighting
Active D-Lighting can not be used with movies.
Noise (randomly-
spaced bright pixels, fog, or lines) may appear in photographs taken
with Active D-Lighting.
Uneven shading may be visible with some
subjects.
Active D-Lighting can not be used at ISO sensitivities of Hi 0.3
or above.
ASee Also
When ADL bracketing is selected for Custom Setting e6 (Auto
bracketing set, 0325), the camera varies Active D-Lighting over a
series of shots.
See page 149 for more information.
G button
J button
186
J
High Dynamic Range (HDR)
Used with high-contrast subjects, High Dynamic Range (HDR)
preserves details in highlights and shadows by combining two
shots taken at different exposures.
HDR is most effective when
used with matrix metering (0123; with other metering methods
and a non-CPU lens, an exposure differential of Auto is equivalent
to about 2 EV).
It can not be used to record NEF (RAW) images.
Movie recording (063), flash lighting (0191), bracketing
(0139), multiple exposure (0210), and time-lapse photography
(0223) can not be used while HDR is in effect and a shutter speed
of A is not available.
1Select HDR (high
dynamic range).
Press the G button to
display the menus.
Highlight HDR (high
dynamic range) in the
shooting menu and press 2.
+
First exposure
(darker)
Second exposure
(brighter)
Combined HDR
image
G button
187
J
2Select a mode.
Highlight HDR mode and
press 2.
Highlight one of the
following and press J.
•To take a series of HDR
photographs, select
0On (series).
HDR
shooting will continue
until you select Off for
HDR mode.
•To take one HDR photograph, select On (single photo).
Normal
shooting will resume automatically after you have created a
single HDR photograph.
•To exit without creating additional HDR photographs, select Off.
If On (series) or On (single photo) is
selected, a y icon will be displayed in
the top control panel.
J button
188
J
3Choose the exposure
differential.
To choose the difference in
exposure between the two
shots, highlight Exposure
differential and press 2.
The options shown at right
will be displayed.
Highlight
an option and press J.
Choose higher values for
high-contrast subjects, but
note that choosing a value
higher than required may not produce the desired results; if
Auto is selected, the camera will automatically adjust
exposure to suit the scene.
4Choose the amount of
smoothing.
To choose how much the
boundaries between the
two images are smoothed,
highlight Smoothing and press 2.
The options shown at right
will be displayed.
Highlight
an option and press J.
Higher values produce a
smoother composite
image.
Uneven shading
may be visible with some subjects.
189
J
5Frame a photograph, focus, and shoot.
The camera takes two exposures when
the shutter-release button is pressed all
the way down.
“ly” will be displayed
in the top control panel and lu in
the viewfinder while the images are
combined; no photographs can be taken
until recording is complete.
Regardless of
the option currently selected for release
mode, only one photograph will be taken
each time the shutter-release button is pressed.
If On (series) is selected, HDR will only turn off when Off is
selected for HDR mode; if On (single photo) is selected, HDR
turns off automatically after the photograph is taken.
The y
icon clears from the display when HDR shooting ends.
DFraming HDR Photographs
The edges of the image may be cropped out.
The desired results may
not be achieved if the camera or subject moves during shooting.
Use of
a tripod is recommended.
Depending on the scene, shadows may
appear around bright objects or halos may appear around dark objects;
this effect can be reduced by adjusting the amount of smoothing.
Top control panel
Viewfinder
190
J
AThe D Button
If HDR (high dynamic range) is selected for
Custom Setting f9 (Assign BKT button; 0335),
you can select the HDR mode by pressing the
D button and rotating the main command
dial and the exposure differential by pressing
the D button and rotating the sub-command
dial.
The mode and exposure differential are
shown in the top control panel: y and R
appear when On (series) is selected and y
when On (single photo) is selected; no icon appears when HDR is off.
AInterval Timer Photography
If On (series) is selected for HDR mode before interval timer shooting
begins, the camera will continue to shoot HDR photographs at the
selected interval (if On (single photo) is selected, interval timer
shooting will end after a single shot).
Ending HDR photography ends
interval timer shooting.
AShooting Menu Banks
HDR settings can be adjusted separately for each bank (0294), but
switching to a bank in which HDR is active during multiple exposure
(0210) or interval timer shooting (0216) disables HDR.
HDR is also
disabled if you switch to a bank in which an NEF (RAW) option is
selected for image quality.
l
191
l
Flash Photography
The camera supports the Nikon Creative Lighting System (CLS) and
can be used with CLS-compatible flash units.
Optional flash units
can be attached directly to the camera accessory shoe as described
below.
The accessory shoe is equipped with a safety lock for flash
units with a locking pin.
1Remove the accessory shoe cover.
2Mount the flash unit on the
accessory shoe.
See the manual provided with the flash
unit for details.
Using a Flash
AThe Sync Terminal
A sync cable can be connected to the sync
terminal as required.
Do not connect another
flash unit via a sync cable when performing rear-
curtain sync flash photography with a flash unit
mounted on the camera accessory shoe.
192
l
The Nikon Creative Lighting System (CLS)
Nikon’s advanced Creative Lighting System (CLS) offers improved
communication between the camera and compatible flash units
for improved flash photography.
❚❚ CLS-Compatible Flash Units
The camera can be used with the following CLS-compatible flash
units:
•The SB-910, SB-900, SB-800, SB-700, SB-600, SB-400, and SB-R200:
•SU-800 Wireless Speedlight Commander: When mounted on a CLS-
compatible camera, the SU-800 can be used as a commander for
remote SB-910, SB-900, SB-800, SB-700, SB-600, or SB-R200 flash
units in up to three groups.
The SU-800 itself is not equipped
with a flash.
Flash unit
SB-910 1SB-900 1SB-800 SB-700 1SB-600 SB-400 2SB-R200 3
Feature
Guide
No. 4
ISO 100 34/111 34/111 38/125 28/92 30/98 21/69 10/33
ISO 200 48/157 48/157 53/174 39/128 42/138 30/98 14/46
1 If a color filter is attached to the SB-910, SB-900, or SB-700 when v or N
(flash) is selected for white balance, the camera will automatically detect the
filter and adjust white balance appropriately.
2 Wireless flash control is not available with the SB-400.
3 Controlled remotely with optional SB-910, SB-900, SB-800, or SB-700 flash unit
or SU-800 wireless Speedlight commander.
4 m/ft, 20 °C (68 °F), SB-910, SB-900, SB-800, SB-700, and SB-600 at 35 mm zoom
head position; SB-910, SB-900, and SB-700 with standard illumination.
AGuide Number
To calculate the range of the flash at full power, divide the Guide
Number by the aperture.
For example, at ISO 100 the SB-800 has a Guide
Number of 38 m or 125 ft. (35mm zoom head position); its range at an
aperture of f/5.6 is 38÷5.6 or about 6.8 meters (or in feet,
125÷5.6=approximately 23 ft. 7 in.).
For each twofold increase in ISO
sensitivity, multiply the Guide Number by the square root of two
(approximately 1.4).
193
l
The following features are available with CLS-compatible flash
units:
1 Only available when SU-800 is used to control other flash units.
The SU-800 itself
is not equipped with a flash.
2 Standard i-TTL flash for digital SLR is used with spot metering or when selected
with flash unit.
3 Standard i-TTL flash for digital SLR is used with spot metering.
4 Selected with flash unit.
5Auto aperture (AA) is used regardless of mode selected with flash unit.
6 Can be selected with camera.
7 Select 1/250 s (Auto FP) for Custom Setting e1 (Flash sync speed, 0323).
8CPU lens required.
Flash unit
SB-910
SB-900
SB-800 SB-700 SB-600 SB-400
Advanced Wireless Lighting
Master/commander Remote
Flash mode/feature
SB-910
SB-900
SB-800
SB-700
SU-800
1
SB-910
SB-900
SB-800
SB-700
SB-600
SB-R200
i-TTL
i-TTL balanced fill-
flash for digital
SLR
✔2✔3✔2✔3✔✔✔✔✔✔
AA Auto aperture ✔4———✔5—✔5✔5——
ANon-TTL auto ✔4———✔5——✔5——
GN Distance-priority
manual ✔✔————————
MManual ✔✔✔✔
6✔✔✔✔✔✔
RPT Repeating flash ✔———✔—✔✔✔—
Auto FP High-Speed Sync 7✔✔✔—✔✔✔✔✔✔
FV lock ✔✔✔✔✔✔✔✔✔✔
AF-assist for multi-area
AF8✔✔✔—✔✔✔———
Flash Color Information
Communication ✔✔✔✔✔✔————
REAR Rear-curtain sync ✔✔✔✔✔✔✔✔✔✔
YRed-eye reduction ✔✔✔✔✔✔————
Power zoom ✔✔✔—✔✔————
194
l
AAuto Aperture/Non-TTL Auto
Unless the focal length and maximum aperture are specified using the
Non-CPU lens data option in the setup menu (0229), choosing auto
aperture (AA) when a non-CPU lens is attached automatically selects
non-TTL auto (A).
AModeling Illumination
CLS-compatible flash units such as the SB-910, SB-900, SB-800, SB-700,
and SB-600 emit a modeling flash when the camera Pv button is
pressed. This feature can be used with Advanced Wireless Lighting to
preview the total lighting effect achieved with multiple flash units.
Modeling illumination can be turned off using Custom Setting e5
Modeling flash (0325).
AOther Flash Units
The following flash units can be used in non-TTL auto and manual
modes.
Flash unit SB-80DX,
SB-28DX,
SB-28, SB-26,
SB-25, SB-24 SB-50DX
SB-30, SB-27 1,
SB-22S, SB-22,
SB-20,
SB-16B, SB-15
SB-23, SB-29 2,
SB-21B2,
SB-29S2
Flash mode
ANon-TTL auto ✔—✔—
MManual ✔✔✔ ✔
GRepeating flash ✔—— —
REAR3Rear-curtain sync ✔✔✔ ✔
1 Flash mode is automatically set to TTL and shutter-release is disabled. Set flash
unit to A (non-TTL auto flash).
2 Autofocus is available with AF-S VR Micro-Nikkor 105mm f/2.8G IF-ED and AF-S
Micro NIKKOR 60mm f/2.8G ED lenses only.
3 Available when camera is used to select flash mode.
195
l
DNotes on Optional Flash Units
Refer to the flash unit manual for detailed instructions.
If the unit
supports CLS, refer to the section on CLS-compatible digital SLR
cameras.
The D4 is not included in the “digital SLR” category in the
SB-80DX, SB-28DX, and SB-50DX manuals.
i-TTL flash control can be used at ISO sensitivities between 100 and
12800.
At values over 12800, the desired results may not be achieved at
some ranges or aperture settings.
If the flash-ready indicator flashes for
about three seconds after a photograph is taken, the flash has fired at
full power and the photograph may be underexposed.
When an SC-series 17, 28, or 29 sync cable is used for off-camera flash
photography, correct exposure may not be achieved in i-TTL mode.
We
recommend that you select standard i-TTL flash control.
Take a test shot
and view the results in the monitor.
In i-TTL, use the flash panel or bounce adapter provided with the flash
unit.
Do not use other panels such as diffusion panels, as this may
produce incorrect exposure.
196
l
DNotes on Optional Flash Units (Continued)
The SB-910, SB-900, SB-800, SB-700, SB-600, and SB-400 provide red-eye
reduction, while the SB-910, SB-900, SB-800, SB-700, SB-600, and SU-800
provide AF-assist illumination with the following restrictions:
•SB-910 and SB-900: AF-assist
illumination is available with
17–135 mm AF lenses, however,
autofocus is available only with
the focus points shown at right.
• SB-800, SB-600, and SU-800: AF-assist
illumination is available with
24–105 mm AF lenses, however,
autofocus is available only with
the focus points shown at right.
•SB-700: AF-assist illumination is
available with 24–135 mm AF
lenses, however, autofocus is
available only with the focus
points shown at right.
In exposure mode e, the maximum aperture (minimum f-number) is
limited according to ISO sensitivity, as shown below:
Maximum aperture at ISO equivalent of:
100 200 400 800 1600 3200 6400 12800
44.85.66.789.51113
If the maximum aperture of the lens is smaller than given above, the
maximum value for aperture will be the maximum aperture of the lens.
17–19 mm 20–105 mm
106–135 mm
24–34 mm 35–49 mm 50–105 mm
24–27 mm 28–135 mm
197
l
AFlash Control Mode
The information display shows the flash control mode for optional flash
units as follows:
Flash sync Auto FP (0323)
i-TTL
Auto aperture (AA)
Non-TTL auto flash (A)
Distance-priority manual
(GN)
Manual
Repeating flash —
Advanced wireless
lighting
DUse Only Nikon Flash Accessories
Use only Nikon flash units.
Negative voltages or voltages over 250 V
applied to the accessory shoe could not only prevent normal operation,
but damage the sync circuitry of the camera or flash.
Before using a
Nikon flash unit not listed in this section, contact a Nikon-authorized
service representative for more information.
198
l
i-TTL Flash Control
When a CLS-compatible flash unit is set to TTL, the camera
automatically selects one of the following types of flash control:
i-TTL balanced fill-flash for digital SLR: Flash unit emits series of nearly invisible
preflashes (monitor preflashes) immediately before main flash.
Preflashes reflected from objects in all areas of frame are picked up by
RGB sensor with approximately 91K (91,000) pixels and are analyzed in
combination with range information from matrix metering system to
adjust flash output for natural balance between main subject and
ambient background lighting.
If type G or D lens is used, distance
information is included when calculating flash output.
Precision of
calculation can be increased for non-CPU lenses by providing lens data
(focal length and maximum aperture; see 0228).
Not available when
spot metering is used.
Standard i-TTL flash for digital SLR: Flash output adjusted to bring lighting in
frame to standard level; brightness of background is not taken into
account.
Recommended for shots in which main subject is emphasized
at expense of background details, or when exposure compensation is
used.
Standard i-TTL flash for digital SLR is activated automatically when
spot metering is selected.
199
l
Flash Modes
The camera supports the following flash modes:
Flash mode Description
Front-
curtain sync
This mode is recommended for most situations.
In
programmed auto and aperture-priority auto modes,
shutter speed will automatically be set to values between
1/250 and 1/60 s (1/8,000 to 1/60 s with Auto FP High-Speed
Sync; 0323).
Red-eye
reduction
Choose this mode (available with SB-910, SB-900, SB-800,
SB-700, SB-600, and SB-400 only) to reduce “red-eye” effect
sometimes caused by flash.
Not recommended with
moving subjects or in other situations in which quick
shutter response is required.
Do not move camera during
shooting.
Red-eye
reduction
with slow
sync
Combines red-eye reduction with slow sync.
Use for
portraits taken against a backdrop of night scenery.
Available only with SB-910, SB-900, SB-800, SB-700, SB-600,
and SB-400 in programmed auto and aperture-priority
auto exposure modes.
Use of a tripod is recommended to
prevent blurring caused by camera shake.
Slow sync
Flash is combined with shutter speeds as slow as 30 s to
capture both subject and background at night or under
dim light.
This mode is only available in programmed auto
and aperture-priority auto exposure modes.
Use of tripod
is recommended to prevent blurring caused by camera
shake.
Rear-curtain
sync
In shutter-priority auto or manual exposure mode, flash
fires just before the shutter closes.
Use to create effect of a
stream of light behind moving objects.
In programmed
auto and aperture-priority auto, slow rear-curtain sync is
used to capture both subject and background.
Use of
tripod is recommended to prevent blurring caused by
camera shake.
200
l
❚❚ Choosing a Flash Mode
To choose the flash mode, press
the M button and rotate the main
command dial until the desired
flash mode is selected in the top
control panel:
1Y icon flashes if flash unit does not support red-eye reduction.
2 Red-eye reduction with slow sync is available only in exposure modes e
and g.
In modes f and h, red-eye reduction with slow sync becomes
red-eye reduction.
3 Available only in exposure modes e and g.
In modes f and h, slow sync
becomes front-curtain sync.
4 In exposure modes e and g, flash-sync mode will be set to slow
rear-curtain sync when the M button is released.
M button Main command
dial
Rear-curtain sync4Slow sync 3
Front-curtain sync Red-eye reduction 1
Red-eye reduction with
slow sync 1, 2
201
l
AStudio Flash Systems
Rear-curtain sync can not be used with studio flash systems, as the
correct synchronization can not be obtained.
AShutter Speed and Aperture
Shutter speed and aperture can be set as follows when an optional flash
unit is used:
Mode Shutter speed Aperture See page
eSet automatically by camera
(1/250 s–1/60 s) 1, 2 Set automatically
by camera
126
fValue selected by user
(1/250 s–30 s) 2127
gSet automatically by camera
(1/250 s–1/60 s) 1, 2 Value selected
by user 3
128
hValue selected by user
(1/250 s–30 s, A)2129
1 Shutter speed may be set as slow as 30 s in slow sync, slow rear-curtain
sync, and slow sync with red-eye reduction flash modes.
2 Speeds as fast as 1/8,000 s are available with optional SB-910, SB-900, SB-800,
SB-700, and SB-600 flash units when 1/250 s (Auto FP) is selected for
Custom Setting e1 (Flash sync speed, 0323).
3 Flash range varies with aperture and ISO sensitivity.
When setting aperture
in exposure modes g and h, consult the table of flash ranges provided with
optional flash unit.
ASee Also
For information on choosing a flash sync speed, see Custom Setting e1
(Flash sync speed, 0323).
For information on choosing the slowest
shutter speed available when using the flash, see Custom Setting e2
(Flash shutter speed, 0324).
202
l
Flash Compensation
Flash compensation can be used with i-TTL or AA flash control
(available with compatible flash units only) to alter flash output by
from –3EV to +1EV in increments of 1/3EV, changing the
brightness of the main subject relative to the background.
Flash
output can be increased to make the main subject appear
brighter, or reduced to prevent unwanted highlights or reflections.
In general, choose positive values to make the main subject
brighter, negative values to make it darker.
To choose a value for flash
compensation, press the M button
and rotate the sub-command dial
until the desired value is
displayed in the top control panel.
M button Sub-command
dial
±0 EV
(M button pressed)
–0.3 EV +1.0 EV
203
l
At values other than ±0.0, a Y icon will be displayed in the top
control panel and E will be displayed in the viewfinder after you
release the M button.
The current value for flash compensation can
be confirmed by pressing the M button.
Normal flash output can be restored by setting flash
compensation to ±0.0.
Flash compensation is not reset when the
camera is turned off.
AOptional Flash Units
The SB-910, SB-900, SB-800, SB-700, and SB-600 also allow flash
compensation to be set using the controls on the flash unit; the value
selected with the flash unit is added to the value selected with the
camera.
ASee Also
For information on choosing the size of the increments available for
flash compensation, see Custom Setting b3 (Exp./flash comp. step
value, 0313).
For information on choosing whether flash
compensation is applied in addition to exposure compensation when
the flash is used, see Custom Setting e4 (Exposure comp. for flash,
0325).
For information on automatically varying flash level over a
series of shots, see page 139.
204
l
FV Lock
This feature is used to lock flash output, allowing photographs to
be recomposed without changing the flash level and ensuring that
flash output is appropriate to the subject even when the subject is
not positioned in the center of the frame.
Flash output is adjusted
automatically for any changes in ISO sensitivity and aperture.
FV
lock is available with CLS compatible flash units only (0192).
To use FV lock:
1Assign FV lock to the Fn button.
Select FV lock for Custom Setting f3
(Assign Fn button > Press, 0328).
2Attach a CLS-compatible flash unit.
Mount a CLS-compatible flash unit (0193) on the camera
accessory shoe.
3Set the flash unit to the appropriate mode.
Turn the flash unit on and set the flash mode to TTL, monitor
pre-flash AA, or monitor pre-flash A.
See the Speedlight
instruction manual for details.
205
l
4Focus.
Position the subject in the
center of the frame and press
the shutter-release button
halfway to focus.
5Lock flash level.
After confirming that the flash-ready
indicator (M) is displayed in the
viewfinder, press the Fn button.
The
flash will emit a monitor preflash to
determine the appropriate flash level.
Flash output will be locked at this level
and FV lock icons (P and e) will
appear in the top control panel and
viewfinder.
6Recompose the photograph.
7Take the photograph.
Press the shutter-release button the rest of the way down to
shoot.
If desired, additional pictures can be taken without
releasing FV lock.
Fn button
206
l
8Release FV lock.
Press the Fn button to release FV lock.
Confirm that the FV lock
icons (P and e) are no longer displayed in the top control
panel and viewfinder.
AMetering
The metering areas for FV lock are as follows:
Flash unit Flash mode Metered area
Stand-alone flash unit
i-TTL 6-mm circle in center of frame
AA Area metered by flash exposure
meter
Used with other flash
units (Advanced
Wireless Lighting)
i-TTL Entire frame
AA Area metered by flash exposure
meter
A (master
flash)
ASee Also
For information on using the Pv button or center of the sub-selector for
FV lock, see Custom Setting f4 (Assign preview button, 0333) or
Custom Setting f6 (Assign sub-selector center, 0333).
t
207
t
Other Shooting Options
The camera settings listed below can be
restored to default values by holding the S
and U buttons down together for more
than two seconds (these buttons are marked
by a green dot).
The control panels turn off
briefly while settings are reset.
Two-Button Reset: Restoring
Default Settings
S
button
U
button
208
t
❚❚ Settings Accessible from the Shooting Menu1
1
With the exception of multiple exposure and interval timer settings, only
settings in the bank currently selected using the
Shooting menu bank
option
will be reset (
0294
).
Settings in the remaining banks are unaffected.
2 Current Picture Control only.
3 Exposure differential and smoothing are not reset.
4 If multiple exposure is currently in progress, shooting will end and multiple
exposure will be created from exposures recorded to that point.
Gain and
number of shots are not reset.
5 If interval timer shooting is currently in progress, shooting will end.
Starting
time, shooting interval, and number of intervals and shots are not reset.
Option Default
Image quality JPEG normal
Image size Large
White balance Auto > Normal
Fine-tuning A-B: 0, G-M: 0
Picture Control
settings 2Unmodified
HDR (high
dynamic range) Off 3
ISO sensitivity 100
Auto ISO
sensitivity control Off
Multiple exposure Off 4
Interval timer
shooting Off 5
Live view
photography Quiet
Option Default
209
t
❚❚ Other Settings
1 Focus point not displayed if auto-area AF is selected for AF-area mode.
2 Number of shots is reset to zero.
Bracketing increment is reset to 1EV
(exposure/flash bracketing) or 1 (white balance bracketing). Y Auto is
selected for the second shot of two-shot ADL bracketing programs.
3 Only settings in the bank currently selected using the Custom settings
bank option will be reset (0305).
Settings in the remaining banks are
unaffected.
Option Default
Focus point 1Center
Exposure mode Programmed
auto
Flexible program Off
Exposure
compensation Off
AE lock hold Off
Aperture lock Off
Shutter-speed lock Off
Autofocus mode AF-S
AF-area mode
Viewfinder Single-point AF
Live view/movie Normal-area AF
Live view
monitor hue --
Metering Matrix metering
Bracketing Off 2
Flash mode Front-curtain
sync
Flash
compensation Off
FV lock Off
Exposure delay
mode Off 3
Option Default
ASee Also
See page 412 for a list of default settings.
210
t
Multiple Exposure
Follow the steps below to record a series of two to ten exposures
in a single photograph.
Multiple exposures can make use of RAW
data from the camera image sensor to produce colors noticeably
superior to those in software-generated photographic overlays.
❚❚ Creating a Multiple Exposure
Multiple exposures can not be recorded in live view.
Exit live view
before proceeding.
Note that at default settings, shooting will end
and a multiple exposure will be recorded automatically if no
operations are performed for 30 s.
1Select Multiple
exposure in the
shooting menu.
Press the G button to
display the menus.
Highlight Multiple
exposure in the shooting menu and press 2.
AExtended Recording Times
For an interval between exposures of more than 30 s, extend the meter-
off delay using Custom Setting c2 (Standby timer, 0316).
The
maximum interval between exposures is 30 s longer than the option
selected for Custom Setting c2.
If no operations are performed for 30 s
after the monitor has turned off during playback or menu operations,
shooting will end and a multiple exposure will be created from the
exposures that have been recorded to that point.
G button
211
t
2Select a mode.
Highlight Multiple exposure
mode and press 2.
Highlight one of the
following and press J:
•To take a series of multiple
exposures, select 0On
(series).
Multiple
exposure shooting will
continue until you select
Off for Multiple exposure mode.
•To take one multiple exposure, select On (single photo).
Normal
shooting will resume automatically after you have created a
single multiple exposure.
•To exit without creating additional multiple exposures, select Off.
If On (series) or On (single photo) is
selected, a n icon will be displayed in
the top control panel.
J button
212
t
3Choose the number of
shots.
Highlight Number of shots
and press 2.
Press 1 or 3 to choose the
number of exposures that will
be combined to form a single
photograph and press J.
AThe D Button
If Multiple exposure is selected for
Custom Setting f9 (Assign BKT button;
0335), you can select the multiple
exposure mode by pressing the D button
and rotating the main command dial and
the number of shots by pressing the D
button and rotating the sub-command
dial. The mode and number of shots are
shown in the top control panel:
nFappears when On (series) is selected and n when On (single
photo) is selected; no icon appears when multiple exposure is off.
213
t
4Choose the amount of
gain.
Highlight Auto gain and press
2.
The following options will be
displayed.
Highlight an option
and press J.
•On: Gain is adjusted
according to number of
exposures actually recorded
(gain for each exposure is set to 1/2 for 2 exposures, 1/3 for
3exposures, etc.).
•Off: Gain is not adjusted when recording multiple exposure.
Recommended if background is dark.
5Frame a photograph, focus, and shoot.
In continuous high-speed and continuous low-
speed release modes (0111), the camera records all
exposures in a single burst.
If On (series) is selected, the
camera will continue to record multiple exposures while the
shutter-release button is pressed; if On (single photo) is
selected, multiple exposure shooting will end after the first
photograph.
In self-timer mode, the camera will automatically
record the number of exposures selected in Step 3 on page
212, regardless of the option selected for Custom Setting c3
(Self-timer) > Number of shots (0317); the interval between
shots is however controlled by Custom Setting c3 (Self-timer)
> Interval between shots.
In other release modes, one
photograph will be taken each time the shutter-release button
is pressed; continue shooting until all exposures have been
recorded (for information on interrupting a multiple exposure
before all photographs are recorded, see page 214).
214
t
The n icon will flash until shooting ends.
If On (series) is selected, multiple
exposure shooting will only end when
Off is selected for multiple exposure
mode; if On (single photo) is selected,
multiple exposure shooting ends automatically when the
multiple exposure is complete.
The n icon clears from the
display when multiple exposure shooting ends.
❚❚ Interrupting Multiple Exposures
To interrupt a multiple exposure before the
specified number of exposures have been
taken, select Off for multiple exposure mode.
If shooting ends before the specified number
of exposures have been taken, a multiple
exposure will be created from the exposures
that have been recorded to that point.
If Auto gain is on, gain will
be adjusted to reflect the number of exposures actually recorded.
Note that shooting will end automatically if:
• A two-button reset is performed (0207)
• The camera is turned off
• The battery is exhausted
•Pictures are deleted
215
t
DMultiple Exposure
Do not remove or replace the memory card while recording a multiple
exposure.
Multiple exposures can not be recorded in live view. Taking
photographs in live view resets Multiple exposure mode to Off.
Noise (randomly-spaced bright pixels, fog, or lines) may appear in
photographs taken with Off selected for auto gain (0213).
The information listed in the playback photo information display
(including date of recording and camera orientation) is for the first shot
in the multiple exposure.
AVoice Memos
Voice recording is disabled while multiple exposures are being shot, but
a memo can be recorded when shooting finishes (0255).
AInterval Timer Photography
If interval timer photography is activated before the first exposure is
taken, the camera will record exposures at the selected interval until the
number of exposures specified in the multiple exposure menu have
been taken (the number of shots listed in the interval timer shooting
menu is ignored).
These exposures will then be recorded as a single
photograph and interval timer shooting will end (if On (single photo) is
selected for multiple exposure mode, multiple exposure shooting will
also end automatically).
Cancelling multiple exposure cancels interval
timer shooting.
AOther Settings
While a multiple exposure is being shot, memory cards can not be
formatted and some menu items are grayed out and can not be
changed.
216
t
Interval Timer Photography
The camera is equipped to take photographs automatically at
preset intervals.
1Select Interval timer
shooting in the
shooting menu.
Press the G button to
display the menus.
Highlight Interval timer
shooting in the shooting
menu and press 2.
DBefore Shooting
Select a release mode other than self-timer (E) when using the interval
timer.
Before beginning interval timer photography, take a test shot at
current settings and view the results in the monitor.
Before choosing a starting time, select Time zone and date in the setup
menu and make sure that the camera clock is set to the correct time and
date (031).
Use of a tripod is recommended.
Mount the camera on a tripod before
shooting begins.
To ensure that shooting is not interrupted, be sure the
camera EN-EL18 battery is fully charged. If in doubt, charge the battery
before use or use an EH-6b AC adapter and EP-6 power connector
(available separately).
G button
217
t
2Choose a starting time.
Chose from the following
starting triggers.
•To start shooting immediately,
highlight Now and press 2.
Shooting begins about 3 s
after settings are completed; proceed to Step 3.
•
To choose a starting time
,
highlight
Start time
and
press
2
to display the start
time options shown at right.
Press
4
or
2
to highlight
hours or minutes and press
1
or
3
to change.
Press
2
to continue.
3Choose the interval.
Press 4 or 2 to highlight
hours, minutes, or seconds;
press 1 or 3 to change.
Choose an interval longer than
the time needed to take the
number of shots selected in Step 4.
If the interval is too short,
the number of photos taken may be less than the total listed in
Step 4 (the number of intervals multiplied by the number of
shots per interval).
Press 2 to continue.
218
t
4Choose the number of
intervals and number of
shots per interval.
Press 4 or 2 to highlight
number of intervals or number
of shots; press 1 or 3 to
change.
Press 2 to continue.
5Start shooting.
Highlight On and press J
(to return to the shooting
menu without starting the
interval timer, highlight
Off and press J).
The first
series of shots will be taken
at the specified starting time, or after about 3 s if Now was
selected for Choose start time in Step 2.
Shooting will
continue at the selected interval until all shots have been
taken.
Note that because the shutter speed, frame rate, and
time needed to record images may vary from one interval to
the next, the time between the end of one interval and the
beginning of the next may vary.
If shooting can not proceed
at current settings (for example, if a shutter speed of A is
currently selected in manual exposure mode or the start time
is in less than a minute), a warning will be displayed in the
monitor.
Number of
intervals
Number
of shots/
interval
Total
number of
shots
J button
219
t
ACover the Viewfinder
To prevent light entering via the viewfinder interfering with exposure,
close the viewfinder eyepiece shutter (0114).
DOut of Memory
If the memory card is full, the interval timer will remain active but no
pictures will be taken.
Resume shooting (0221) after deleting some
pictures or turning the camera off and inserting another memory card.
DInterval Timer Photography
Interval timer photography can not be combined with long time-
exposures (bulb photography, 0131) or time-lapse photography
(0223) and is not available when Record movies is selected for
Custom Setting g4 (Assign shutter button, 0343).
ABracketing
Adjust bracketing settings before starting interval timer photography.
If exposure, flash, or ADL bracketing is active while interval timer
photography is in effect, the camera will take the number of shots in the
bracketing program at each interval, regardless of the number of shots
specified in the interval timer menu.
If white balance bracketing is
active while interval timer photography is in effect, the camera will take
one shot at each interval and process it to create the number of copies
specified in the bracketing program.
220
t
ADuring Shooting
During interval timer photography, the Q
icon will flash in the top control panel.
Immediately before the next shooting interval
begins, the shutter speed display will show the
number of intervals remaining, and the
aperture display will show the number of shots remaining in the current
interval.
At other times, the number of intervals remaining and the
number of shots in each interval can be viewed by pressing the shutter-
release button halfway (once the button is released, the shutter speed
and aperture will be displayed until the standby timer expires).
To view current interval timer settings, select
Interval timer shooting between shots.
While
interval timer photography is in progress, the
interval timer menu will show the starting time,
the shooting interval, and the number of
intervals and shots remaining.
None of these
items can be changed while interval timer
photography is in progress.
Pictures can be played back and shooting and menu settings can be
adjusted freely while interval timer photography is in progress. The
monitor will turn off automatically about four seconds before each
interval.
221
t
❚❚ Pausing Interval Timer Photography
Interval timer photography can be paused by:
• Pressing the J button between intervals
• Highlighting Start >Pause in the interval timer menu and
pressing J
• Turning the camera off and then on again (if desired, the
memory card can be replaced while the camera is off)
• Selecting self-timer (E) release mode
To resume shooting:
1Choose a new starting
time.
Choose a new starting time as
described on page 217.
2Resume shooting.
Highlight Restart and
press J.
Note that if
interval timer photography
was paused during
shooting, any shots
remaining in the current
interval will be canceled.
J button
222
t
❚❚ Interrupting Interval Timer Photography
Interval timer shooting will end automatically if the battery is
exhausted.
Interval timer photography can also be ended by:
• Selecting Start >Off in the interval timer menu
• Performing a two button reset (0207)
• Resetting settings for the current shooting menu bank using the
Shooting menu bank item in the shooting menu (0294)
• Changing bracketing settings (0139)
• Terminating HDR (0186) or multiple exposure shooting (0210)
Normal shooting will resume when interval timer photography ends.
❚❚ No Photograph
The camera will skip the current interval if any of the following
situations persist for eight seconds or more after the interval was
due to start: the photograph or photographs for the previous
interval have yet to be taken, the memory buffer is full, or the
camera is unable to focus in
AF-S
(note that the camera focuses again
before each shot).
Shooting will resume with the next interval.
ARelease Mode
Regardless of the release mode selected, the camera will take the
specified number of shots at each interval.
In CH (continuous high
speed) mode, photographs will be taken at the rate given on page 112.
In S (single frame) and CL (continuous low-speed) modes, photographs
will be taken at the rate chosen for Custom Setting d2 (Shooting speed,
0318) > Continuous low-speed; in mode J, camera noise will be
reduced.
AShooting Menu Banks
Changes to interval timer settings apply to all shooting menu banks
(0294).
If shooting menu settings are reset using the Shooting menu
bank item in the shooting menu (0294), interval timer settings will be
reset as follows:
• Choose start time: Now
• Interval: 00:01':00"
• Number of intervals: 1
• Number of shots: 1
• Start shooting: Off
223
t
Time-Lapse Photography
The camera automatically takes photos at selected intervals to
create a silent time-lapse movie using the options currently
selected for Movie settings in the shooting menu (0293).
1Select Time-lapse
photography in the
shooting menu.
Press the G button to
display the menus.
Highlight Time-lapse
photography in the shooting menu and press 2.
ABefore Shooting
Before beginning time-lapse photography, take a test shot at current
settings (framing the photo in the viewfinder for an accurate exposure
preview) and view the results in the monitor.
To record changes in
brightness, choose manual exposure (0129); for consistent coloration,
choose a white balance setting other than auto (0153).
We also
recommend that you briefly switch to movie live view and check the
current image area crop in the monitor (063); note, however, that
time-lapse photography is not available in live view.
Use of a tripod is recommended.
Mount the camera on a tripod before
shooting begins.
To ensure that shooting is not interrupted, use an
optional EH-6b AC adapter and EP-6 power connector or a fully-charged
EN-EL18 battery.
G button
224
t
2Press 2.
Press 2 to proceed to Step 3
and choose an interval and
shooting time.
To record a
time-lapse movie using the
default interval of 5 seconds and shooting time of 25 minutes,
proceed to step 5.
3Choose the interval.
Press 4 or 2 to highlight
minutes, or seconds; press 1 or
3 to change.
Choose an
interval longer than the
slowest anticipated shutter
speed.
Press 2 to continue.
4Select the shooting time.
Press 4 or 2 to highlight hours
or minutes; press 1 or 3 to
change.
The maximum
shooting time is 7 hours and
59 minutes.
Press 2 to
continue.
DFrame Size
The area used for metering exposure, flash level, or auto white balance
when photographs are recorded at a movie frame size of 1920 × 1080;
30 fps; crop, 1920 × 1080; 25 fps; crop, or 1920 × 1080; 24 fps; crop
(074) is not the same as the area in the final photograph, with the
result that optimal results may not be achieved. Take test shots and
check the results in the monitor.
225
t
5Start shooting.
Highlight On and press J
(to return to the shooting
menu without starting
time-lapse photography,
highlight Off and press J).
Time-lapse photography starts after 3 s.
The camera takes
photographs at the interval selected in Step 3 for the time
selected in Step 4.
The memory card access lamp lights while
each shot is recorded; note that because shutter speed and
the time needed to record the image to the memory card may
vary from shot to shot, the interval between a shot being
recorded and the start of the next shot may vary.
Shooting
will not begin if a time-lapse movie can not be recorded at
current settings (for example, if the memory card is full, the
interval or shooting time is zero, or the interval is longer than
the shooting time).
When complete, time-lapse movies are recorded to the
memory card selected for Movie settings > Destination
(075).
DTime-Lapse Photography
Time-lapse is not available in live view (049, 63), at a shutter speed of
A (0131) or when bracketing (0139), High Dynamic Range (HDR,
0186), multiple exposure (0210), or interval timer photography
(0216) is active.
ARelease Mode
Regardless of the release mode selected, the camera will take one shot
at each interval.
The self-timer can not be used.
J button
226
t
ACalculating the Length of the Final Movie
The total number of frames in the final movie
can be calculated by dividing the shooting time
by the interval and rounding up.
The length of
the final movie can then be calculated by diving
the number of shots by the frame rate selected
for Movie settings > Frame size/frame rate.
A
48 frame movie recorded at 1920 × 1080;
24 fps, for example, will be about two seconds
long.
The maximum length for movies recorded
using time-lapse photography is 20 minutes.
ACover the Viewfinder
To prevent light entering via the viewfinder
interfering with exposure, close the viewfinder
eyepiece shutter (0114).
ADuring Shooting
During time-lapse photography, Q will flash
and the time-lapse recording indicator will be
displayed in the top control panel.
The time
remaining (in hours and minutes) appears in the
shutter-speed display immediately before each
frame is recorded.
At other times, the time remaining can be viewed by
pressing the shutter-release button halfway.
Regardless of the option
selected for Custom Setting c2 (Standby timer, 0316), the standby
timer will not expire during shooting.
To view current time-lapse photography
settings, press the G button between shots.
While time-lapse photography is in progress, the
time-lapse photography menu will show the
interval and the time remaining.
These settings
can not be changed while time-lapse
photography is in progress, nor can pictures be
played back or other menu settings adjusted.
Frame size/
frame rate
Memory card
indicator
Length recorded/
maximum length
227
t
❚❚ Interrupting Time-Lapse Photography
Time-lapse photography will end automatically if the battery is
exhausted. The following will also end time-lapse photography:
•Selecting Start > Off in the Time-lapse photography menu
• Pressing the J button between frames or immediately after a
frame is recorded
• Turning the camera off
• Removing the lens
• Connecting a USB or HDMI cable
• Inserting a memory card into an empty slot
• Pressing the shutter-release button all the way down to take a
photograph
A movie will be created from the frames shot to the point where
time-lapse photography ended. Note that time-lapse
photography will end and no movie will be recorded if the power
source is removed or disconnected or the destination memory
card is ejected.
❚❚ No Photograph
The camera will skip the current frame if the camera is unable to
focus in AF-S (note that the camera focuses again before each shot).
Shooting will resume with the next frame.
AImage Review
The K button can not be used to view pictures while time-lapse
photography is in progress, but the current frame will be displayed for a
few seconds after each shot if On is selected for Image review in the
playback menu (0289).
Other playback operations can not be
performed while the frame is displayed.
ASee Also
For information on setting a beep to sound when time-lapse
photography is complete, see Custom Setting d1 (Beep, 0318).
228
t
Non-CPU Lenses
By specifying lens data (lens focal length and maximum aperture),
the user can gain access to a variety of CPU lens functions when
using a non-CPU lens (0385).
If the focal length of the lens is known:
• Power zoom can be used with optional flash units (0193)
• Lens focal length is listed (with an asterisk) in the playback photo
info display
If the maximum aperture of the lens is known:
• The aperture value is displayed in the top control panel and
viewfinder
• Flash level is adjusted for changes in aperture
• Aperture is listed (with an asterisk) in the playback photo info
display
Specifying both the focal length and maximum aperture of the lens:
• Enables color matrix metering (note that it may be necessary to
use center-weighted or spot metering to achieve accurate results
with some lenses, including Reflex-NIKKOR lenses)
• Improves the precision of center-weighted and spot metering
and i-TTL balanced fill-flash for digital SLR
AFocal Length Not Listed
If the correct focal length is not listed, choose the closest value greater
than the actual focal length of the lens.
ATeleconverters and Zoom Lenses
The maximum aperture for teleconverters is the combined maximum
aperture of the teleconverter and the lens.
Note that lens data are not
adjusted when non-CPU lenses are zoomed in or out.
The data for
different focal lengths can be entered as separate lens numbers, or the
data for the lens can be edited to reflect the new values for lens focal
length and maximum aperture each time zoom is adjusted.
229
t
The camera can store data for up to nine non-CPU lenses.
To enter
or edit data for a non-CPU lens:
1Select Non-CPU lens
data in the setup menu.
Press the G button to
display the menus.
Highlight Non-CPU lens
data in the setup menu
and press 2.
2Select a lens number.
Highlight Lens number and
press 4 or 2 to choose a lens
number between 1 and 9.
3Enter the focal length and
aperture.
Highlight Focal length (mm)
or Maximum aperture and
press 4 or 2 to edit the
highlighted item.
Focal length can be selected from values
between 6 and 4,000 mm, maximum aperture from values
between f/1.2 and f/22.
G button
230
t
4Select Done.
Highlight Done and press
J.
The specified focal
length and aperture will be
stored under the chosen
lens number.
To recall lens data when using a non-CPU lens:
1Assign non-CPU lens number selection to a camera
control.
Select Choose non-CPU lens number as the “Press +
command dials” option for a camera control in the Custom
Settings menu (0332).
Non-CPU lens number selection can
be assigned to the Fn button (Custom Setting f3, Assign Fn
button, 0328), the Pv button (Custom Setting f4, Assign
preview button, 0333), or the center of the sub-selector
(Custom Setting f6, Assign sub-selector center, 0333).
2Use the selected control to choose a lens number.
Press the selected control and rotate the main or sub-
command dial until the desired lens number is displayed in
the top control panel.
J button
Lens number
Main command dial
Focal
length
Maximum
aperture
231
t
Using a GPS Unit
A GPS unit can be connected to the ten-pin remote terminal,
allowing the current latitude, longitude, altitude, Coordinated
Universal Time (UTC), and heading to be recorded with each
photograph taken.
The camera can be used with an optional GP-1
GPS unit (see below; note that the GP-1 does not provide the
compass heading), or with compatible third-party units connected
via an optional MC-35 GPS adapter cord (0395).
❚❚ The GP-1 GPS Unit
The GP-1 is an optional GPS unit designed for use with Nikon
digital cameras.
For information on connecting the unit, see the
manual provided with the GP-1.
232
t
AThe k Icon
Connection status is shown by the k icon:
•k (static): Camera has established
communication with a GPS device. Photo
information for pictures taken while this icon
is displayed include an additional page of GPS
data (0245).
•k (flashing): The GPS device is searching for a signal. Pictures taken
while the icon is flashing do not include GPS data.
•No icon: No new GPS data have been received from the GPS device for
at least two seconds.
Pictures taken when the k icon is not displayed do not include GPS
data.
AHeading
The heading is only recorded if the GPS device is
equipped with a digital compass (note that the
GP-1 is not equipped with a compass).
Keep the
GPS device pointing in the same direction as the
lens and at least 20cm (8 in.) from the camera.
ACoordinated Universal Time (UTC)
UTC data is provided by the GPS device and is independent of the
camera clock.
233
t
❚❚ Setup Menu Options
The GPS item in the setup menu contains the options listed below.
•Standby timer: Choose whether or not the exposure meters will
turn off automatically when a GPS unit is attached.
•Position: This item is only available if a GPS device is connected,
when it displays the current latitude, longitude, altitude,
Coordinated Universal Time (UTC), and heading (if supported) as
reported by the GPS device.
•Use GPS to set camera clock: Select Yes to synchronize the
camera clock with the time reported by the GPS device.
Option Description
Enable
Exposure meters will turn off automatically if no operations
are performed for the period specified in Custom Setting c2
(Standby timer (0316); to allow the camera time to
acquire GPS data when a GP-1 is connected, the delay is
extended by up to one minute after exposure meters are
activated or the camera is turned on).
This reduces the
drain on the battery.
Disable Exposure meters will not turn off while a GPS unit is
connected; GPS data will always be recorded.
234
t
I
235
I
More About Playback
Full-Frame Playback
To play photographs back, press the K button.
The
most recent photograph will be displayed in the
monitor.
Additional pictures can be displayed by
pressing 4 or 2; to view additional information on
the current photograph, press 1 or 3 (0238).
Thumbnail Playback
To view multiple images, press the W button when
a picture is displayed full frame.
The number of
images displayed increases from 4 to 9 to 72 each
time the W button is pressed, and decreases with
each press of the X button.
Use the multi selector
to highlight images and press the center of the
multi selector to view the highlighted image full
frame.
Viewing Images
W
X
W
X
W
X
Full-frame
playback Thumbnail playback
K button
W button
236
I
Playback Controls
J+
Display slot/folder selection dialog.
To choose card and
folder from which pictures are played back, highlight slot
and press 2 to display list of folders, then highlight folder
and press J.
J+Create retouched copy of current photograph (0363) or
create edited copy of current movie (079).
J+
View the IPTC presets stored on the camera (0354).
To
embed IPTC preset in current photo, highlight preset and
press J (any preset already embedded in current photo
will be replaced).
J+Upload photographs over a wireless or Ethernet network
(0269).
ATwo Memory Cards
If two memory cards are inserted, you can select a memory card for
playback by pressing the W button when 72 thumbnails are displayed.
L (Z/Q):Protect the current picture (0249)
X:Zoom in (0247)
J: Use in combination with the multi
selector as described below
O (Q): Delete the current picture (0251)
W: View multiple images (0235)
G: View the menus (0283)
H:Record and play
voice memos
(0258)
237
I
ARotate Tall
To display “tall” (portrait-orientation)
photographs in tall orientation, select On for
the Rotate tall option in the playback menu
(0290).
AImage Review
When On is selected for Image review in the playback menu (0289),
photographs are automatically displayed in the monitor after shooting
(because the camera is already in the correct orientation, images are not
rotated automatically during image review).
In continuous release
mode, display begins when shooting ends, with the first photograph in
the current series displayed.
AResuming Shooting
To turn the monitor off and return to shooting mode, press K or press
the shutter-release button halfway.
Photographs can be taken
immediately.
AThe Multi Selector
The multi selector can be used to
highlight pictures in the thumbnail
display and in displays like that shown
at right.
ASee Also
For information on choosing how long the monitor will remain on when
no operations are performed, see Custom Setting c4 (Monitor off
delay, 0317).
For information on choosing the role played by the
center of the multi selector, see Custom Setting f1 (Multi selector
center button, 0327).
For information on using the command dials
for image or menu navigation, see Custom Setting f10 (Customize
command dials)>Menus and playback (0337).
238
I
Photo Information
Photo information is superimposed on images displayed in full-
frame playback.
Press 1 or 3 to cycle through photo information
as shown below.
Note that “image only”, shooting data, RGB
histograms, and highlights are only displayed if corresponding
option is selected for Playback display options (0285).
GPS
data are only displayed if a GPS device was used when the photo
was taken, while IPTC presets are displayed only if embedded in
the photo (0354).
File information None (image only) Overview data
Highlights GPS data
RGB histogram
Shooting data
IPTC preset
100NC_D4
D
S
C_
0001. JP
G
15
/
04
/
2011 10:02:27
N
OR
OR
M
AL
AL
4928x3280
1
/
12
0, 0
1
/
125 F5. 6
100 50
mm
100NC_D4
D
S
C_
0001. JP
G
15
/
04
/
2011 10:02:27
N
I
KO
N
D4
1
/
12
N
N
OR
OR
M
AL
AL
4928x3280
100
-
1
RGB
Highlights
Select R, G, B
:
:
:
:
:
:
:
E
N
L
AT I TUDE
01 15 00
::
TI
M
E(UTC)
35
º
35 971
'
.
ALT I TUDE
LONG I T UDE
35
m
9.696
'
13
º
43
15
/
04
/
2011
N
I
KO
N
D4
100
-
1
100
-
1
RGB
M
TR, SP
D
,
AP
.
E
XP.
M
O
D
E
, I S
O
F
OCAL
LE
N
G
T
H
LE
N
S
A
F
/
V
R
FL
A
S
H
TYPE
SYNC MODE
,
:
, 1
/
125 , F5. 6
:
, 100
:
0.
0
:
50
mm
:
50
/
1. 4
:
S
:
:
:
N
I
KO
N
D4
100
-
1
IPTC
Caption
Event ID
Headline
Object Name
City
State
Country
:
:
:
:
:
:
:
N
I
KO
N
D4
100
-
1
239
I
❚❚ File Information
1 Displayed only if Focus point is selected for Playback display options (0285).
2 If photograph was taken using AF-S, display shows point where focus first locked.
If
photograph was taken using AF-C, focus point is only displayed if option other than
auto-area AF was selected for AF-area mode and camera was able to focus.
3 Displayed in yellow if picture is in non-FX format (including DX-based movie format;
071, 85).
1
/
12
100NC_D4
D
S
C_
0001. JP
G
15
/
04
/
2011 10:02:27
N
OR
OR
M
AL
AL
4928x3280
1 2 3 4 5 76
14
13
12 11 10 9
15
8
1Voice memo icon ...................................255
2Protect status..........................................249
3Retouch indicator..................................361
4IPTC preset indicator....................236, 354
5Focus point 1, 2 ........................................103
6AF area brackets 1....................................38
7Frame number/total number of frames
8Image quality ...........................................90
9Image size .................................................93
10 Image area 3..............................................85
11 Time of recording....................................31
12 Date of recording ....................................31
13 Current card slot ......................................35
14 Folder name ...........................................296
15 File name.................................................298
240
I
❚❚ Highlights
1 Flashing areas indicate highlights (areas that may be
overexposed) for current channel.
Hold W button
and press 4 or 2 to cycle through channels as
follows:
2 Displayed in yellow if picture is in non-FX format (including DX-based movie format;
071, 85).
100
-
1
RGB
Highlights
Select R, G, B
1 2
34
1Image highlights 1
2Folder number–frame number 2....... 296
3Highlight display indicator
4Current channel1
W button
RGB
(all channels)
R
(red)
G
(green)
B
(blue)
241
I
❚❚ RGB Histogram
1 Flashing areas indicate highlights (areas that may be
overexposed) for current channel.
Hold W button
and press 4 or 2 to cycle through channels as
follows:
2 Displayed in yellow if picture is in non-FX format (including DX-based movie format;
071, 85).
100
-
1
RGB
1
2
5
6
7
8
4
3
1Image highlights 1
2Folder number–frame number 2 .......296
3White balance ........................................153
Color temperature ................................160
White balance fine-tuning..................156
Preset manual ........................................163
4Current channel 1
5Histogram (RGB channel).
In all
histograms, horizontal axis gives pixel
brightness, vertical axis number of
pixels.
6Histogram (red channel)
7Histogram (green channel)
8Histogram (blue channel)
W button
RGB
(all channels)
R
(red)
G
(green)
B
(blue)
Highlight display off
242
I
APlayback Zoom
To zoom in on the photograph when the
histogram is displayed, press
X
.
Use the
X
and
W
buttons to zoom in and out and scroll the
image with the multi selector.
The histogram will
be updated to show only the data for the portion
of the image visible in the monitor.
AHistograms
Camera histograms are intended as a guide only and may differ from
those displayed in imaging applications.
Some sample histograms are
shown below:
If the image contains objects with
a wide range of brightnesses, the
distribution of tones will be
relatively even.
If the image is dark, tone
distribution will be shifted to the
left.
If the image is bright, tone
distribution will be shifted to the
right.
Increasing exposure compensation shifts the distribution of tones to
the right, while decreasing exposure compensation shifts the
distribution to the left. Histograms can provide a rough idea of overall
exposure when bright ambient lighting makes it difficult to see
photographs in the monitor.
243
I
❚❚ Shooting Data
1Metering method ................................. 123
Shutter speed .............................. 127, 129
Aperture......................................... 128, 129
2Exposure mode ..................................... 125
ISO sensitivity 1...................................... 117
M
TR, SP
D
,
AP
.
E
XP.
M
O
D
E
, I S
O
F
OCAL
LE
N
G
T
H
LE
N
S
A
F
/
V
R
FL
A
S
H
TYPE
SYNC MODE
,
:
, 1
/
8000 , F2. 8
:
, Hi
0. 3
:
+1. 3, +5
/
6
:
50
mm
:
50
/
1. 4
:
C
:
Optional
:
SL
O
W
:
TTL-BL, +1. 0
N
I
KO
N
D4
100
-
1
1
2
3
4
5
6
7
8
9
10 1211
3Exposure compensation......................137
Optimal exposure tuning 2..................315
4Focal length...................................228, 389
5Lens data.................................................228
6Focus mode ..............................................97
Lens VR (vibration reduction) 3
7Flash type 4
Commander mode 4
8Flash mode 4...........................................199
9Flash control 4.........................................324
Flash compensation 4...........................202
10 Camera name
11 Image area 5..............................................85
12 Folder number–frame number 5 .......296
W
HITE B
A
LANCE
CO
L
O
R SP
AC
E
PI
C
TURE
C
TRL
QUICK ADJUST
S
H
A
RPE
N
ING
CO
N
TR
A
ST
BRI
G
H
T
N
ESS
S
A
TUR
A
TI
O
N
H
U
E
:
AUTO1
, 0, 0
:
s
RGB
: ST
A
N
D
A
R
D
:
0
:
3
:
0
:
0
:
0
:
0
N
I
KO
N
D4
100
-
1
13
14
15
16
17
18
19
20
21
13 White balance ........................................153
Color temperature ................................160
White balance fine-tuning..................156
Preset manual ........................................163
14 Color space .............................................299
15 Picture Control.......................................173
16 Quick adjust6.........................................176
Original Picture Control7.....................173
17 Sharpening .............................................176
18 Contrast ...................................................176
19 Brightness ...............................................176
20 Saturation 8.............................................176
Filter effects 9..........................................176
21 Hue 8.........................................................176
Toning 9....................................................176
244
I
The fourth page of the shooting data is
only displayed if copyright information was
recorded with the photograph as described
on page 353.
1 Displayed in red if photo was taken with auto ISO sensitivity control on.
2 Displayed if Custom Setting b6 (Fine-tune optimal exposure, 0315) has been set to
a value other than zero for any metering method.
3 Displayed only if VR lens is attached.
4 Displayed only if optional flash unit (0191) is used.
5 Displayed in yellow if picture is in non-FX format (including DX-based movie format;
071, 85).
6Standard Vivid, Portrait, and Landscape Picture Controls only.
7Neutral, Monochrome, and custom Picture Controls.
8 Not displayed with monochrome Picture Controls.
9 Monochrome Picture Controls only.
NOISE REDUC.
ACT.
D-LIGHT.
HDR
VIGNETTE CTRL
RETOUCH
COMMENT
:
HI ISO/LONG EXP.
:
NORMAL
:
AUTO, NORMAL
:
NORMAL
:
WARM FILTER
:
SPRING HAS COME.
N
I
KO
N
D4
100
-
1
22
23
24
25
26
27
22 High ISO noise reduction.................... 302
Long exposure noise reduction ........ 302
23 Active D-Lighting ................................. 184
24 HDR exposure differential.................. 188
HDR smoothing .................................... 188
25 Vignette control.................................... 300
26 Retouch history..................................... 361
27 Image comment ................................... 352
ART
IST
C
O
PYRI
GHT
:
NIKON
TARO
:
NIKON
N
I
KO
N
D4
100
-
1
28
29
28 Name of photographer....................... 353
29 Copyright holder .................................. 353
245
I
❚❚ GPS Data1 (0231)
1 Data for movies are for start of recording.
2 Displayed only if GPS device is equipped with electronic compass.
3 Displayed in yellow if picture is in non-FX format (including DX-based movie format;
071, 85).
❚❚ IPTC Preset (0354)
1 Displayed in yellow if picture is in non-FX format (including DX-based movie format;
071, 85).
:
:
:
:
:
:
:
E
N
L
AT I TUDE
15
/
04
/
2011
01 15 00
::
TI
M
E(UTC)
35
º
35 971
'
.
ALT I TUDE
LONG I T UDE
35
m
9.696
'
13
º
43
N
I
KO
N
D4
100
-
1
1
2
3
4
6 87
5
1Latitude
2Longitude
3Altitude
4Coordinated Universal Time (UTC)
5Heading 2
6Camera name
7Image area 3..............................................85
8Folder number–frame number 3 .......296
IPTC
Caption
Event ID
Headline
Object Name
City
State
Country
:
:
:
:
:
:
:
N
I
KO
N
D4
100
-
1
1
2
3
4
5
6
7
8109
1Caption
2Event ID
3Headline
4Object name
5City
6State
7Country
8Camera name
9Image area 1..............................................85
10 Folder number–frame number 1 .......296
IPTC
Category
Supp. Cat
Byline
Byline title
Writer/Editor
Credit
Source
:
:
:
:
:
:
:
N
I
KO
N
D4
100
-
1
11
13
12
14
15
16
17
11 Category
12 Supplemental Categories (Supp. Cat.)
13 Byline
14 Byline title
15 Writer/editor
16 Credit
17 Source
246
I
❚❚ Overview Data
1 Displayed in yellow if picture is in non-FX format (including DX-based movie format;
071, 85).
2 Displayed in red if photo was taken with auto ISO sensitivity control on.
1
/
8000 F2. 8
H
i 0. 3 50
mm
–
1. 3 +1. 0 SLOW
0, 0
N
1
/
8000 F2. 8
H
i 0. 3 50
mm
–
1. 3 +1. 0 SLOW
0, 0
N
100NC_D4
D
S
C_
0001. JP
G
15
/
04
/
2011 10:15:00
NIKON
D4
1
/
12
N
OR
OR
M
AL
AL
4928x3280
1 234
7
5
8
6
21
22
23
30
18 19 20
28 2627 25 24
29
1716
15
12 1011 914 13
1Frame number/total number of frames
2Voice memo icon ..................................255
3Protect status.........................................249
4Retouch indicator .................................361
5Camera name
6IPTC preset indicator ...................236, 354
7Histogram showing the distribution of
tones in the image (0242).
8Image quality........................................... 90
9Image size................................................. 93
10 Image area 1............................................. 85
11 File name.................................................298
12 Time of recording.................................... 31
13 Folder name ...........................................296
14 Date of recording.................................... 31
15 Current card slot...................................... 35
16 Metering method .................................123
17 Exposure mode .....................................125
18 Shutter speed............................... 127, 129
19 Aperture ........................................ 128, 129
20 ISO sensitivity 2...................................... 117
21 Focal length .................................. 228, 389
22 GPS data indicator................................ 231
23 Image comment indicator ................. 352
24 Active D-Lighting ................................ 184
25 Picture Control ...................................... 173
26 Color space............................................. 299
27 Flash mode............................................. 199
28 White balance ....................................... 153
Color temperature................................ 160
White balance fine-tuning ................. 156
Preset manual ....................................... 163
29 Flash compensation............................. 202
Commander mode
30 Exposure compensation..................... 137
247
I
Taking a Closer Look:
Playback Zoom
Press the X button to zoom in on the image
displayed in full-frame playback or on the image
currently highlighted in thumbnail playback. The
following operations can be performed while
zoom is in effect:
To Use Description
Zoom in
or out X/W
Press X to zoom 36×24
(3 : 2) format images in
to maximum of
approximately 30 ×
(large images), 23 ×
(medium images) or
15 × (small images).
Press W to zoom out.
While photo is zoomed in, use multi selector
to view areas of image not visible in
monitor.
Keep multi selector pressed to
scroll rapidly to other areas of frame.
Navigation window is displayed when zoom
ratio is altered; area currently visible in
monitor is indicated by yellow border.
View
other
areas of
image
Select
faces
Faces (up to 35)
detected during zoom
are indicated by white
borders in navigation
window.
Rotate sub-
command dial to view
other faces.
X
button
248
I
View
other
images
Rotate main command dial to view same
location in other photos at current zoom
ratio.
Playback zoom is cancelled when a
movie is displayed.
Change
protect
status
L (Z/Q) See page 249 for more information.
Return to
shooting
mode
/ KPress the shutter-release button halfway or
press the K button to exit to shooting
mode.
Display
menus GSee page 283 for more information.
To Use Description
249
I
Protecting Photographs from
Deletion
In full-frame, zoom, and thumbnail playback, the L (Z/Q)
button can be used to protect photographs from accidental
deletion.
Protected files can not be deleted using the O (Q)
button or the Delete option in the playback menu.
Note that
protected images will be deleted when the memory card is
formatted (036, 345).
To protect a photograph:
1Select an image.
Display the image in full-frame playback or playback zoom or
highlight it in the thumbnail list.
2Press the L (Z/Q)
button.
The photograph will be
marked with a P icon.
To
remove protection from
the photograph so that it
can be deleted, display
the photograph or highlight it in the thumbnail list and then
press the L (Z/Q) button.
L (Z/Q) button
250
I
AVoice Memos
Changes to the protect status of images also apply to any voice memos
that may have been recorded with the images. Voice memo overwrite
status can not be set separately.
ARemoving Protection from All Images
To remove protection from all images in the folder or folders currently
selected in the Playback folder menu, press the L (Z/Q) and O (Q)
buttons together for about two seconds during playback.
251
I
Deleting Photographs
To delete all photographs in the current folder or the photograph
displayed in full-frame playback or highlighted in the thumbnail
list, press the O (Q) button.
To delete multiple selected
photographs, use the Delete option in the playback menu.
Once
deleted, photographs can not be recovered.
Note that pictures
that are protected or hidden can not be deleted.
Full-Frame and Thumbnail Playback
Press the O (Q) button to delete the current photograph.
1Select an image.
Display the image or highlight it in the thumbnail list.
2Press the O (Q)
button.
The menu shown at right
will be displayed;
highlight Selected image
(to delete all pictures in
the folder currently
selected for playback—
0284— press 3 and
choose a slot).
O (Q) button
252
I
3Delete the photograph(s).
To delete the photograph or photographs, press the O (Q)
button (Selected image) or J button (All images).
To exit
without deleting the photograph or photographs, press the
K button.
ASee Also
The After delete option in the playback menu determines whether the
next image or the previous image is displayed after an image is deleted
(0290).
AVoice Memos
If a voice memo has been recorded with the
selected image, the confirmation dialog shown
at right will be displayed when Selected image
is chosen in Step 2 on the previous page.
This
dialog is not displayed when All images is
selected.
•Image/voice memo: Select this option and press the O (Q) button to
delete both photo and voice memo.
•Voice memo only: Select this option and press the O (Q) button to
delete only the voice memo.
To exit without deleting either voice memo or photo, press K.
253
I
The Playback Menu
Select Delete in the playback menu to delete pictures and their
associated voice memos.
Note that depending on the number of
images, some time may be required for deletion.
❚❚ Selected: Deleting Selected Photographs
1Choose Selected for the
Delete option in the
playback menu.
Press the G button and
select Delete in the
playback menu.
Highlight
Selected and press 2.
2Highlight a picture.
Use the multi selector to
highlight a picture (to view
the highlighted picture full
screen, press and hold the
X button; to view images
in other locations, press W
and select the desired card
and folder as described on
page 236).
Option Description
QSelected Delete selected pictures.
RAll
Delete all pictures in the folder currently selected for
playback (0284). If two cards are inserted, you can select
the card from which pictures will be deleted.
G button
X button
254
I
3Select the highlighted
picture.
Press the center of the multi
selector to select the
highlighted picture.
Selected
pictures are marked by a O icon.
Repeat steps 2 and 3 to select
additional pictures; to deselect a picture, highlight it and press
the center of the multi selector.
4Press J to complete
the operation.
A confirmation dialog will
be displayed; highlight
Yes and press J. J button
e
255
e
Voice Memos
Voice memos up to sixty seconds long can be added to
photographs using the built-in or optional ME-1 stereo
microphones.
Readying the Camera for Recording
Before recording voice memos, adjust settings using the Voice
memo options item in the setup menu.
❚❚ Voice Memo
This option controls whether voice memos
are recorded automatically or manually.
The
following options are available:
Recording Voice Memos
Option Description
7Off Voice memos can not be recorded in shooting mode.
8
On
(Auto and
manual)
Selecting this option displays
menu shown at right; select
maximum recording time from
5, 10, 20, 30, 45, or 60 s.
Unless
On is selected for Image
review in playback menu
(0289), recording will begin
when shutter-release button is released after
shooting.
Recording ends when H button is pressed
or after specified recording time has ended.
9Manual
only
Memo can be recorded for most recent photograph
by pressing and holding H button (0257).
256
e
❚❚ Voice Memo Overwrite
This option controls whether the voice memo
for the most recent photograph can be
overwritten in shooting mode.
The following
options are available:
❚❚ Voice Memo Button
This option controls manual recording.
The
following options are available:
Option Description
Disable
Voice memo can not be recorded in
shooting mode if one already exists for
most recent image.
Enable
Voice memo can be recorded in
shooting mode even if one already
exists for most recent image (0257).
Existing memo will be deleted and
replaced by new memo.
Option Description
!Press and
hold
Voice memo is recorded while H
button is held down.
Recording
will end automatically after 60 s.
$
Press to
start/
stop
Recording begins when H
button is pressed and ends
when H button is pressed again.
Recording will end
automatically after 60 s.
AVoice Memo
The option selected for Voice memo is indicated by an icon in the rear
control panel.
On (auto and manual) Manual only
257
e
Automatic Recording (Shooting Mode)
If On (Auto and manual) is selected for Voice memo (0255),
a voice memo will be added to the most recent photograph when
shooting ends.
Recording will end when the H button is pressed
or after the specified recording time has ended.
Manual Recording (Shooting Mode)
If On (Auto and manual) or Manual only is
selected for Voice memo (0255), a voice
memo can be recorded for the most recent
photograph by pressing and holding the H
button.
A voice memo will be recorded while
the button is held down (note that no voice
memo will be recorded if the H button is not
held down for at least one second).
DAutomatic Recording
Voice memos will not be recorded automatically during live view
(049), movie recording (063), or time-lapse photography (0223), or
when On is selected for the Image review option (0289) in the
playback menu.
A voice memo can however be added to the
photograph displayed during image review even if Off is selected for
Voice memo.
ASecondary slot function
If two memory cards are inserted and
Backup
or
RAW primary, JPEG
secondary
is selected for the
Secondary slot function
option (
0
95) in
the shooting menu, voice memos will be associated with the images
recorded to the memory card in the primary slot.
H button
258
e
Playback Mode
To add a voice memo to the photograph currently displayed in
full-frame playback or highlighted in the thumbnail list (0235):
1Choose a photograph.
Display or highlight the photograph.
Only one voice memo can be recorded
per image; additional voice memos can
not be recorded for images already
marked with a h icon.
2Press and hold the H button.
A voice memo will be recorded while the
H button is held down (note that no voice
memo will be recorded if the H button is
not held down for at least one second).
ADuring Recording
During recording, the C icon in the rear
control panel will flash.
A countdown timer
in the rear control panel shows the length of
the voice memo that can be recorded (in
seconds).
In playback mode, a C icon is displayed in the
monitor during recording.
H button
Rear control panel
259
e
AInterrupting Recording
Pressing the shutter-release button or operating other camera controls
may end recording.
During interval timer photography, recording ends
automatically about two seconds before the next photograph is taken.
Recording also ends automatically when the camera is turned off.
AAfter Recording
If a voice memo has been recorded for the
most recent photograph, a C icon will be
displayed in the rear control panel.
If a voice memo exists for the photograph
currently selected in playback mode, a h icon
will be displayed in the monitor.
AVoice Memo File Names
Voice memos are stored as WAV files with names of the form
“xxxxnnnn.WAV,” where “xxxxnnnn” is a file name copied from the image
with which the voice memo is associated.
For example, the voice memo
for the image “DSC_0002.JPG” would have the file name
“DSC_0002.WAV.”
Voice memo file names can be viewed on a computer.
Rear control panel
260
e
Playing Voice Memos
Voice memos can be played back over the
camera’s built-in speaker when the associated
image is viewed in full-frame playback or
highlighted in the thumbnail list (0235).
The
presence of a voice memo is indicated by an
h icon.
To Press Description
Start/end playback H
Press H to start playback.
Playback will end
when H button is pressed again or entire
memo has been played back.
Delete voice memo OSee page 252.
AInterrupting Playback
Pressing the shutter-release button or operating other camera controls
may end playback.
Playback ends automatically when another image is
selected or the camera is turned off.
261
e
Voice Memo Playback Options
The Voice memo options > Audio output
item in the setup menu controls whether
voice memos are played back by the camera
(from either the built-in speaker or optional
headphones) or by a device to which the
camera is connected via an HDMI cable.
When sound is played back by the camera,
the Audio output option also controls
playback volume.
Option Description
%Speaker/
headphones
Voice memos are played
back over built-in speaker or
(if connected) over optional
headphones. Selecting this
option displays menu shown
at right.
Press 1 or 3 to
change volume.
Beep will
sound when option is selected.
Press J to make
selection and return to setup menu.
&HDMI Audio signal output to HDMI terminal.
(Off
Voice memos are not played back.
b icon is
displayed when photo for which voice memo exists
is viewed in monitor.
262
e
Q
263
Q
Connections
This section describes how to use the supplied UC-E15 USB cable
to connect the camera to a computer.
Before Connecting the Camera
Before connecting the camera, install the software on the supplied
ViewNX 2 installer CD.
To ensure that data transfer is not
interrupted, be sure the camera EN-EL18 battery is fully charged.
If
in doubt, charge the battery before use or use an EH-6b AC
adapter and EP-6 power connector (available separately).
❚❚ Supplied Software
ViewNX 2 includes a
“Nikon Transfer 2” function for
copying pictures from the
camera to the computer,
where ViewNX 2 can be used
to view and print selected
images or to edit photographs and movies.
Before installing
ViewNX 2, confirm that your computer meets the system
requirements on page 266.
Connecting to a Computer
Your Imaging Toolbox
264
Q
1Start the computer and insert the ViewNX 2 installer
CD.
2Select a language.
If the desired language is not
available, click Region Selection
to choose a different region and
then choose the desired
language (region selection is not
available in the European
release).
3Start the installer.
Click Install and follow the on-
screen instructions.
Windows Mac OS
Double-click icon on
desktop
Double-click Welcome
icon
DInstallation Guide
For help installing ViewNX 2, click
Installation Guide
in Step 3.
q Select region (if required)
w Select
language
e Click Next
Click Install
265
Q
4Exit the installer.
Click Yes (Windows) or OK (Mac OS) when installation is
complete.
The following software is installed:
•ViewNX 2
• Apple QuickTime (Windows only)
5Remove the installer CD from the CD-ROM drive.
Windows Mac OS
Click Yes Click OK
DConnecting Cables
Be sure the camera is off when connecting or disconnecting interface
cables.
Do not use force or attempt to insert the connectors at an angle.
Close the connector cover when the connector is not in use.
AWindows
To visit the Nikon website after installing ViewNX 2, select All
Programs > Link to Nikon from the Windows start menu (Internet
connection required).
ACamera Control Pro 2
Camera Control Pro 2 software (available separately; 0393) can be
used to control the camera from a computer.
When
Camera Control Pro 2 is used to capture photographs directly to the
computer, the capture mode indicator (c) will appear and the PC
connection indicator will flash in the top control panel.
266
Q
DSystem Requirements
Windows
CPU
•Photos/JPEG movies: Intel Celeron, Pentium 4, or Core series,
1.6 GHz or better
•H.264 movies (playback): 3.0 GHz or better Pentium D; Intel Core i5
or better recommended when viewing movies with a frame
size of 1,280 × 720 or more at a frame rate of 30 fps or above or
movies with a frame size of 1,920 × 1,080 or more
•H.264 movies (editing): 2.6 GHz or better Core 2 Duo
OS
Pre-installed versions of Windows 7 Home Basic/
Home Premium/Professional/Enterprise/Ultimate (Service Pack 1),
Windows Vista Home Basic/Home Premium/Business/Enterprise/
Ultimate (Service Pack 2), or 32-bit editions of Windows XP
Home Edition/Professional (Service Pack 3). All installed programs
run as 32-bit applications in 64-bit editions of Windows 7 and
Windows Vista.
RAM •Windows 7/Windows Vista: 1 GB or more (2 GB or more recommended)
•Windows XP: 512 MB or more (2 GB or more recommended)
Hard-disk space A minimum of 500 MB available on the startup disk (1 GB or more
recommended)
Monitor
•Resolution: 1024 × 768 pixels (XGA) or more (1280 × 1024 pixels (SXGA)
or more recommended)
•Color: 24-bit color (True Color) or more
Mac OS
CPU
•Photos/JPEG movies: PowerPC G4 (1 GHz or better), G5, Intel Core, or
Xeon series
•H.264 movies (playback): PowerPC G5 Dual or Core Duo, 2 GHz or
better; Intel Core i5 or better recommended when viewing
movies with a frame size of 1,280 × 720 or more at a frame rate
of 30 fps or above or movies with a frame size of 1,920 × 1,080
or more
•H.264 movies (editing): 2.6 GHz or better Core 2 Duo
• GPU that supports QuickTime H.264 hardware acceleration
recommended
OS Mac OS X version 10.5.8, 10.6.8, or 10.7.2
RAM 512 MB or more (2 GB or more recommended)
Hard-disk space A minimum of 500 MB available on the startup disk (1 GB or more
recommended)
Monitor
•Resolution: 1024 × 768 pixels (XGA) or more (1280 × 1024 pixels (SXGA) or
more recommended)
•Color: 24-bit color (millions of colors) or more
267
Q
Direct USB Connection
Connect the camera using the supplied UC-E15 USB cable.
1Turn the camera off.
2Turn the computer on.
Turn the computer on and wait for it to start up.
3Connect the USB cable.
Connect the USB cable as shown.
4Turn the camera on.
DUSB Hubs
Connect the camera directly to the computer; do not connect the
cable via a USB hub or keyboard.
DThe USB Cable Clip
To prevent cable from being disconnected, attach the clip as
shown.
268
Q
5Start Nikon Transfer 2.
If a message is displayed prompting you to choose a program,
select Nikon Transfer 2.
6Click Start Transfer.
At default settings, all the pictures on
the memory card will be copied to the
computer (for more information on
using Nikon Transfer 2, start ViewNX 2 or
Nikon Transfer 2 and select ViewNX 2
Help from the Help menu).
7Turn the camera off and disconnect the USB cable
when transfer ends.
Nikon Transfer 2 will close automatically when transfer is
complete.
AWindows 7
If the following dialog is displayed, select Nikon Transfer 2 as
described below.
1Under Import pictures and
videos, click Change program.
A program selection dialog will
be displayed; select Import file
using Nikon Transfer 2 and
click OK.
2Double-click Import file.
DDuring Transfer
Do not turn the camera off or disconnect the USB cable while
transfer is in progress.
Start Transfer
269
Q
Ethernet and Wireless Networks
The camera can be connected to Ethernet or wireless networks
using the built-in Ethernet port or an optional WT-5 or WT-4
wireless transmitter.
Note that an Ethernet cable (available
separately from commercial sources) is required for an Ethernet
connection.
❚❚ The Built-in Ethernet Port and WT-5 Wireless Transmitter
The following modes are available when the camera is connected
to a network using the built-in Ethernet port or an optional WT-5
wireless transmitter:
❚❚ WT-4 Wireless Transmitter
The WT-4 can be used in any of the following modes:
Mode Function
FTP upload Upload existing photos and movies to a computer or ftp
server, or upload new photos as they are taken.
Image transfer
Camera
control
Control camera from computer using
Camera Control Pro 2 (available separately).
HTTP server Take photos and view existing photos remotely from a
browser-equipped computer or iPhone.
Synchronized
release (WT-5
only)
Synchronize the shutter releases of multiple remote
cameras with a controlling “master” camera.
Mode Function
Transfer mode Upload existing photos and movies to a computer or ftp
server, or upload new photos as they are taken.
Thumbnail
select mode
Preview photographs on computer monitor before
upload.
PC mode Control camera from computer using
Camera Control Pro 2 (available separately).
Print mode Print JPEG photographs on printer connected to network
computer.
270
Q
For more information, see the Network Guide and the
documentation provided with the wireless transmitter.
Be sure to
update to the latest versions of the wireless transmitter firmware
and supplied software.
DImage Upload
In image transfer, ftp upload, and transfer modes, the picture currently
displayed in full-frame or thumbnail playback can be uploaded to the
computer by holding J and pressing the center of the multi selector.
ADuring Transfer
Movies can not be recorded or played back in image transfer mode
(“image transfer mode” applies when images are being transferred via
an Ethernet or wireless network and when images remain to be sent).
Live view photography is not available during transfer if Silent is
selected for Live view photography in the shooting menu.
AMovies
Movies can be uploaded in transfer mode if the camera is connected to
an Ethernet or a wireless network and Auto send or Send folder is not
selected for Transfer settings.
Movies can not be uploaded in
thumbnail select mode (WT-4 only).
AHTTP Server Mode
The camera can not be used to record or view movies in http server
mode, while live view photography is not available if Silent is selected
for Live view photography in the shooting menu.
AThumbnail Select Mode
Camera settings can not be changed from the computer in thumbnail
select mode.
AWireless Transmitters
The principal differences between the WT-4 and WT-4A/B/C/D/E and
the WT-5 and WT-5A/B/C/D/E is in the number of channels supported;
unless otherwise stated, all references to the WT-4 also apply to the
WT-4A/B/C/D/E, while all references to the the WT-5 also apply to the
WT-5A/B/C/D/E.
271
Q
Printing Photographs
Selected JPEG images can be printed on a PictBridge printer
(0439) connected directly to the camera.
DSelecting Photographs for Printing
Images created at image quality settings of NEF (RAW) or TIFF (RGB)
(090) can not be selected for printing.
JPEG copies of NEF (RAW)
images can be created using the NEF (RAW) processing option in the
retouch menu (0372).
APrinting Via Direct USB Connection
Be sure the battery is fully charged or use an optional EH-6b AC adapter
and EP-6 power connector.
When taking photographs to be printed via
direct USB connection, set Color space to sRGB (0299).
ASee Also
See page 428 for information on what to do if an error occurs during
printing.
272
Q
Connecting the Printer
Connect the camera using the supplied UC-E15 USB cable.
1Turn the camera off.
2Connect the USB cable.
Turn the printer on and connect the USB cable as shown.
Do
not use force or attempt to insert the connectors at an angle.
3Turn the camera on.
A welcome screen will be displayed in the monitor, followed
by a PictBridge playback display.
DUSB Hubs
Connect the camera directly to the printer; do not connect the
cable via a USB hub.
qw
273
Q
Printing Pictures One at a Time
1Select a picture.
Press 4 or 2 to view additional
pictures. Press 1 or 3 to view
photo information (0238), or
press the X button to zoom in
on the current frame (0247,
press K to exit zoom).
To view six pictures at a time, press the
center of the multi selector.
Use the multi selector to highlight
pictures, or press the center of the multi selector again to
display the highlighted picture full frame.
To view images in
other locations, press W when thumbnails are displayed and
select the desired card and folder as described on page 236.
2Display printing
options.
Press J to display
PictBridge printing
options.
3Adjust printing options.
Press 1 or 3 to highlight an option and press 2 to select.
Option Description
Page size
Highlight a page size (only sizes supported by the
current printer are listed) and press J to select and exit
to the previous menu (to print at the default page size
for the current printer, select Printer default).
No.
of
copies
Press 1 or 3 to choose number of copies (maximum 99),
then press J to select and return to the previous menu.
J button
274
Q
4Start printing.
Select Start printing and press
J to start printing.
To cancel
before all copies have been
printed, press J.
Border
This option is available only if supported by the printer.
Highlight Printer default (use current printer settings),
Print with border (print photo with white border), or No
border and press J to select and exit to the previous
menu.
Time stamp
Highlight Printer default (use current printer settings),
Print time stamp (print times and dates of recording on
photos), or No time stamp and press J to select and
exit to the previous menu.
Cropping
This option is available only if supported by the printer.
To exit without cropping, highlight No cropping and
press J.
To crop the current picture, highlight Crop and
press 2.
Selecting Crop displays the
dialog shown at right.
Press X to
increase the size of the crop, W
to decrease.
Position the crop
using the multi selector and press
J.
Note that print quality may
drop if small crops are printed at
large sizes.
Option Description
275
Q
Printing Multiple Pictures
1Display the PictBridge
menu.
Press the G button in the
PictBridge playback display
(see Step 3 on page 272).
2Choose an option.
Highlight one of the following
options and press 2.
•Print select: Select pictures
for printing.
•Print (DPOF): Print an
existing print order created with the DPOF print order
option in the playback menu (0277). The current print
order will be displayed in Step 3.
•Index print: To create an index print of all JPEG pictures on
the memory card, proceed to Step 4.
Note that if the
memory card contains more than 256 pictures, only the first
256 images will be printed.
G button
276
Q
3Select pictures.
Use the multi selector to
scroll through the pictures
on the memory card (to
view images in other
locations, press W and
select the desired card and
folder as described on
page 236).
To display the
current picture full screen,
press and hold the X
button.
To select the
current picture for printing,
press the L (Z/Q)
button and press 1.
The
picture will be marked with
a Z icon and the number
of prints will be set to 1.
Keeping the L (Z/Q) button pressed, press 1 or 3 to
specify the number of prints (up to 99; to deselect the picture,
press 3 when the number of prints is 1).
Continue until all the
desired pictures have been selected.
4Display printing
options.
Press J to display
PictBridge printing
options.
L (Z/Q) button
X button
J button
277
Q
5Adjust printing options.
Choose page size, border, and time stamp options as
described on page 273 (a warning will be displayed if the
selected page size is too small for an index print).
6Start printing.
Select Start printing and press J to start printing.
To cancel before all copies have been printed,
press J.
Creating a DPOF Print Order: Print Set
The DPOF print order option in the playback menu is used to
create digital “print orders” for PictBridge-compatible printers and
devices that support DPOF (0439).
1Choose Select/set for
the DPOF print order
item in the playback
menu.
Press the G button and
select DPOF print order in
the playback menu.
Highlight Select/set and press 2 (to
remove all photographs from the print order, select Deselect
all?).
G button
278
Q
2Select pictures.
Use the multi selector to
scroll through the pictures
on the memory card (to
view images in other
locations, press W and
select the desired card and
folder as described on
page 236).
To display the
current picture in full
screen, press and hold the
X button.
To select the
current picture for printing,
press the L (Z/Q)
button and press 1.
The
picture will be marked with
a Z icon and the number
of prints will be set to 1.
Keeping the L (Z/Q) button pressed, press 1 or 3 to
specify the number of prints (up to 99; to deselect the picture,
press 3 when the number of prints is 1).
Press J when all the
desired pictures have been selected.
3Select imprint options.
Highlight the following options and
press 2 to toggle the highlighted
option on or off (to complete the print
order without including this
information, proceed to Step 4).
•Print shooting data: Print shutter speed and aperture on all
pictures in print order.
•Print date: Print date of recording on all pictures in print
order.
L (Z/Q) button
X button
279
Q
4Complete the print
order.
Highlight Done and press
J to complete the print
order.
DDPOF Print Orders
To print the current print order when the camera is connected to a
PictBridge printer, select Print (DPOF) in the PictBridge menu and
follow the steps in “Printing Multiple Pictures” to modify and print the
current order (0275).
DPOF print date and shooting data options are
not supported when printing via direct USB connection; to print the
date of recording on photographs in the current print order, use the
PictBridge Time stamp option.
The DPOF print order option can not be used if there is not enough
space on the memory card to store the print order.
Images created at image quality settings of NEF (RAW; 090) can not be
selected for printing using this option.
JPEG copies of NEF (RAW)
images can be created using the NEF (RAW) processing option in the
retouch menu (0372).
Print orders may not print correctly if images are deleted using a
computer or other device after the print order is created.
J button
280
Q
Viewing Photographs on TV
A type C mini-pin High-Definition Multimedia Interface (HDMI)
cable (available separately from commercial sources) can be used
to connect the camera to high-definition video devices.
1Turn the camera off.
Always turn the camera off before connecting or
disconnecting an HDMI cable.
2Connect the HDMI cable as shown.
3Tune the device to the HDMI channel.
4Turn the camera on and press K button.
During playback, images will be displayed both in the camera
monitor and on the high-definition television or monitor
screen.
DClose the Connector Cover
Close the connector cover when the connectors are not in use.
Foreign
matter in the connectors can interfere with data transfer.
Connect to high-definition
device (choose cable with
connector for HDMI
device)
Connect to
camera
281
Q
HDMI Options
The HDMI option in the setup menu (0344) controls output
resolution and other advanced HDMI options.
❚❚ Output Resolution
Choose the format for images output to the
HDMI device.
If Auto is selected, the
camera will automatically select the
appropriate format.
Regardless of the
option selected, Auto will be used for
movie live view, movie recording, and
playback.
❚❚ Advanced
Option Description
Output range
Auto is recommended in most situations.
If the camera
is unable to determine the correct RGB video signal
output range for the HDMI device, you can choose from
the following options:
•Limited range: For devices with an RGB video signal input
range of 16 to 235. Choose this option if you notice loss
of detail in shadows.
•Full range: For devices with an RGB video signal input
range of 0 to 255. Choose this option if shadows are
“washed out” or too bright.
Output display
size
Choose horizontal and vertical frame coverage for HDMI
output from 95% or 100%.
Live view on-
screen display
If Off is selected when the camera is connected to an
HDMI device, shooting information will not be displayed
in the monitor during live view photography.
282
Q
ATelevision Playback
Use of an EH-6b AC adapter and EP-6 power connector (available
separately) is recommended for extended playback.
Note that the
edges may not be visible when photographs are viewed on a television
screen.
AVoice Memo Options > Audio Output (0261)
Set HDMI to play back voice memos on the HDMI device.
ASlide Shows
The Slide show option in the playback menu can be used for
automated playback (0291).
AAudio
Stereo sound recorded with optional ME-1 (0395) stereo microphones
plays in stereo when movies are viewed on HDMI devices using a
camera connected via an HDMI cable (note that audio will not be played
back over headphones connected to the camera).
Volume can be
adjusted using television controls; the camera controls can not be used.
AHDMI and Live View
When the camera is connected via an HDMI cable, HDMI displays can be
used for live view photography and movie live view (061, 70).
During
movie live view and movie recording, HDMI output will be adjusted
according to the option selected for Movie settings > Frame size/
frame rate in the shooting menu (074).
Note that some HDMI devices
may not support the selected setting; in this case, select 1080i
(interlaced) for HDMI > Output resolution (0281).
Movies may be
output at a frame size smaller than that selected for Frame size/frame
rate (074).
U
283
U
Menu Guide
To display the playback menu, press G and select the K
(playback menu) tab.
DThe Playback Menu:
Managing Images
G button
Option 0
Delete 253
Playback folder 284
Hide image 284
Playback display options 285
Copy image(s) 286
Image review 289
After delete 290
Rotate tall 290
Slide show 291
DPOF print order 277
ASee Also
Menu defaults are listed on page 412.
284
U
Choose a folder for playback (0235).
Hide or reveal selected pictures as described below.
Hidden
pictures are visible only in the Hide image menu and can only be
deleted by formatting the memory card.
1Choose Select/set.
Highlight Select/set and
press 2 (to skip the remaining
steps and reveal all pictures,
highlight Deselect all? and
press J).
Playback Folder G button ➜Dplayback menu
Option Description
NC_D4 Pictures in all folders created with the D4 will be visible during
playback.
All Pictures in all folders will be visible during playback.
Current Only pictures in the current folder will be visible during
playback.
Hide Image G button ➜Dplayback menu
DProtected and Hidden Images
Revealing a protected image will also remove protection from the
image.
285
U
2Select pictures.
Use the multi selector to scroll
through the pictures on the
memory card (to view the
highlighted picture full screen,
press and hold the X button; to
view images in other locations, press W and select the
desired card and folder as described on page 236) and press
the center of the multi selector to select the current picture.
Selected pictures are marked by a R icon; to deselect a
picture, highlight it and press the center of the multi selector.
3Press J.
Press J to complete the
operation.
Choose the information
available in the playback photo
information display (0238).
Press 1 or 3 to highlight an
option, then press 2 to select
the option for the photo
information display.
A L
appears next to selected items;
to deselect, highlight and press
2.
To return to the playback
menu, highlight Done and
press J.
Playback Display Options G button ➜Dplayback menu
J button
J button
286
U
Copy pictures from one memory card to another.
1Choose Select source.
Highlight Select source and
press 2.
2Select the source card.
Highlight the slot for the card
containing the images to be
copied and press J.
3Choose Select image(s).
Highlight Select image(s) and
press 2.
Copy Image(s) G button ➜Dplayback menu
Option Description
Select source Choose card from which pictures will be copied.
Select image(s) Select pictures to be copied.
Select destination
folder Select destination folder on remaining card.
Copy image(s)? Copy selected pictures to specified destination.
287
U
4Select the source folder.
Highlight the folder containing
the images to be copied and
press 2.
5Make the initial selection.
Before going on to select or
deselect individual images, you
can mark all or all protected
images in the folder for
copying by choosing Select all
images or Select protected images.
To mark only
individually selected images for copying, choose Deselect all
before proceeding.
6Select additional images.
Highlight pictures and press
the center of the multi selector
to select or deselect (to view
the highlighted picture full
screen, press and hold the X
button).
Selected images are marked with a L.
Press J to
proceed to Step 7 when your selection is complete.
7Choose Select destination
folder.
Highlight Select destination
folder and press 2.
288
U
8Select a destination folder.
To enter a folder number, choose Select
folder by number, enter the number
(0296), and press J.
To choose from a list of existing folders,
choose Select folder from list, highlight
a folder, and press J.
9Copy the images.
Highlight Copy image(s)?
and press J.
A confirmation dialog will
be displayed; highlight Yes and
press J.
Press J again to exit
when copying is complete.
J button
289
U
Choose whether pictures are automatically
displayed in the monitor immediately after
shooting.
If Off is selected, pictures can only
be displayed by pressing the K button.
DCopying Images
Images will not be copied if there is insufficient space on the destination
card.
Be sure the battery is fully charged before copying movies.
If the destination folder contains an image with
the same name as one of the images to be
copied, a confirmation dialog will be displayed.
Select Replace existing image to replace the
image with the image to be copied, or select
Replace all to replace all existing images with
the same names without further prompting.
To
continue without replacing the image, select Skip, or select Cancel to
exit without copying any further images. Hidden or protected files in the
destination folder will not be replaced.
Protect status is copied with the images but print marking (0277) is
not.
Voice memos will be copied with their associated images. Hidden
images can not be copied.
Image Review G button ➜Dplayback menu
290
U
Choose the picture displayed after an image is deleted.
Choose whether to rotate “tall” (portrait-orientation) pictures for
display during playback.
Note that because the camera itself is
already in the appropriate orientation during shooting, images are
not rotated automatically during image review.
After Delete G button ➜Dplayback menu
Option Description
SShow
next
Display following picture.
If deleted picture was last frame,
previous picture will be displayed.
TShow
previous
Display previous picture.
If deleted picture was first frame,
following picture will be displayed.
UContinue
as before
If user was scrolling through pictures in order recorded,
following picture will be displayed as described for Show
next.
If user was scrolling through pictures in reverse
order, previous picture will be displayed as described for
Show previous.
Rotate Tall G button ➜Dplayback menu
Option Description
On
“Tall” (portrait-orientation) pictures are automatically rotated for
display in the camera monitor.
Pictures taken with Off selected for
Auto image rotation (0350) will be displayed in “wide”
(landscape) orientation.
Off “Tall” (portrait-orientation) pictures are displayed in “wide”
(landscape) orientation.
291
U
Create a slide show of the pictures in the current playback folder
(0284).
Hidden images (0284) are not displayed.
To start the slide show, highlight Start and
press J.
The following operations can be
performed while the slide show is in
progress:
Slide Show G button ➜Dplayback menu
Option Description
Start Start slide show.
Image type Choose type of image displayed from Still images and
movies, Still images only, and Movies only.
Frame interval Choose how long each picture will be displayed.
Audio playback Display menu of voice memo playback options
(0292).
To Press Description
Skip back/skip
ahead
Press 4 to return to previous frame, 2 to skip
to next frame.
View additional
photo info
Change or hide photo info (still images only;
0238).
Pause/resume J
Pause or resume slide show. Voice memo
playback may continue after J button has
been pressed.
Exit to playback
menu GEnd slide show and return to playback menu.
Exit to playback
mode KEnd slide show and exit to full-frame or
thumbnail playback (0235).
Exit to shooting
mode
Press shutter-release button halfway to return
to shooting mode.
292
U
The dialog shown at right is displayed when
the show ends.
Select Restart to restart or
Exit to return to the playback menu.
❚❚ Audio Playback
Choose On to play voice memos during slide shows (the sound
recorded with movies always plays regardless of the option
selected). The following options will be displayed:
Choose Off to disable voice memo playback during slide shows.
Option Description
Frame interval Playback ends when next frame is displayed, even if
entire memo has not been played.
Length of voice
memo
Next frame is not displayed until entire memo has been
played, even if frame interval is shorter than voice
memo.
293
U
CThe Shooting Menu:
Shooting Options
To display the shooting menu, press G and select the C
(shooting menu) tab.
G button
Option 0
Shooting menu bank 294
Extended menu banks 295
Storage folder 296
File naming 298
Primary slot selection 95
Secondary slot function 95
Image quality 90
Image size 93
Image area 85
JPEG compression 92
NEF (RAW) recording 92
White balance 153
Set Picture Control 173
Manage Picture Control 179
Color space 299
Active D-Lighting 184
HDR (high dynamic range) 186
Vignette control 300
Auto distortion control 301
Long exposure NR 302
High ISO NR 302
ISO sensitivity settings 117
Multiple exposure 210
Interval timer shooting 216
Live view photography 60
Time-lapse photography 223
Movie settings 74
Option 0
ASee Also
Menu defaults are listed on page 412.
294
U
Shooting menu options are stored in one of four banks.
With the
exceptions of Extended menu banks, Multiple exposure,
Interval timer shooting, Time-lapse photography, and
modifications to Picture Controls (quick adjust and other manual
adjustments), changes to settings in one bank have no effect on the
others.
To store a particular combination of frequently-used settings,
select one of the four banks and set the camera to these settings.
The
new settings will be stored in the bank even when the camera is
turned off, and will be restored the next time the bank is selected.
Different combinations of settings can be stored in the other
banks, allowing the user to switch instantly from one combination
to another by selecting the appropriate bank from the bank menu.
The default names for the four shooting menu banks are A, B, C,
and D.
A descriptive caption up to 20 characters long can be
added as described on page 180 by highlighting the menu bank
and pressing 2.
Shooting Menu Bank G button ➜Cshooting menu
AShooting Menu Bank
The top control panel and information displays
show the current shooting menu bank.
ASee Also
Exposure mode, shutter speed, and aperture can be included in
shooting menu banks using the Extended menu banks option in the
shooting menu (0295). For information on using the controls on the
camera body to select the shooting menu bank, see Custom Setting f3
(Assign Fn button) > Press + command dials (0332).
295
U
❚❚ Restoring Default Settings
To restore default settings,
highlight a bank in the
Shooting menu bank menu
and press O (Q).
A
confirmation dialog will be
displayed; highlight Yes and
press J to restore default
settings for the selected bank.
See page 412 for a list of default
settings.
Select On to include exposure mode, shutter
speed (modes f and h only), and aperture
(modes g and h only) in the information
recorded in each of the four shooting menu
banks, to be recalled whenever the bank is
selected. Selecting Off restores the values in
effect before On was selected.
Extended Menu Banks G button ➜Cshooting menu
O (Q) button
296
U
Select the folder in which subsequent images will be stored.
❚❚ Select Folder by Number
1Choose Select folder by
number.
Highlight Select folder by
number and press 2.
The
dialog shown at right will be
displayed, with the current
primary slot (095) underlined.
2Choose a folder number.
Press 4 or 2 to highlight a digit, press 1 or 3 to change.
If a
folder with the selected number already exists, a W, X, or Y
icon will be displayed to the left of the folder number:
•W : Folder is empty.
•X : Folder is partially full.
•Y : Folder contains 999 pictures or a picture numbered
9999.
No further pictures can be stored in this folder.
3Save changes and exit.
Press
J
to complete the operation and return to the shooting
menu (to exit without changing the storage folder, press the
G
button).
If a folder with the specified number does not
already exist, a new folder will be created on the card in the
primary slot.
Subsequent photographs will be stored in the
selected folder unless it is already full.
Storage Folder G button ➜Cshooting menu
297
U
❚❚ Select Folder from List
1Choose Select folder from
list.
Highlight Select folder from
list and press 2.
2Highlight a folder.
Press 1 or 3 to highlight a folder.
3Select the highlighted folder.
Press J to select the highlighted folder and return to the
shooting menu.
Subsequent photographs will be stored in
the selected folder.
DFolder and File Numbers
If the current folder is numbered 999 and contains 999 pictures or a
picture numbered 9999, the shutter-release will be disabled and no
further photographs can be taken.
To continue shooting, create a folder
with a number less than 999, or select an existing folder with a number
less than 999 and less than 999 images.
AStartup Time
Additional time may be required for camera startup if the memory card
contains a very large number of files or folders.
298
U
Photographs are saved using file names consisting of “DSC_” or, in
the case of images that use the Adobe RGB color space (0299),
“_DSC”, followed by a four-digit number and a three-letter
extension (e.g., “DSC_0001.JPG”).
The File naming option is used
to select three letters to replace the “DSC” portion of the file name.
For information on editing file names, see page 180.
File Naming G button ➜Cshooting menu
AExtensions
The following extensions are used: “.NEF” for NEF (RAW) images, “.TIF”
for TIFF (RGB) images, “.JPG” for JPEG images, “.MOV” for movies, and
“.NDF” for dust off reference data. In each pair of photographs recorded
at image-quality settings of NEF (RAW)+JPEG, the NEF and JPEG images
have the same file names but different extensions.
299
U
The color space determines the gamut of colors available for color
reproduction.
Choose sRGB for photographs that will be printed
or used “as is,” with no further modification.
Adobe RGB has a
wider color gamut and is recommended for images that will be
extensively processed or retouched after leaving the camera.
Color Space G button ➜Cshooting menu
AColor Space
Color spaces define the correspondence between colors and the
numeric values that represent them in a digital image file.
The sRGB
color space is widely used, while the Adobe RGB color space is typically
used in publishing and commercial printing.
sRGB is recommended
when taking photographs that will be printed without modification or
viewed in applications that do not support color management, or when
taking photographs that will be printed with ExifPrint, the direct
printing option on some household printers, or kiosk printing or other
commercial print services.
Adobe RGB photographs can also be printed
using these options, but colors will not be as vivid.
JPEG photographs taken in the Adobe RGB color space are DCF
compliant; applications and printers that support DCF will select the
correct color space automatically.
If the application or device does not
support DCF, select the appropriate color space manually.
An ICC color
profile is embedded in TIFF photographs taken in the Adobe RGB color
space, allowing applications that support color management to
automatically select the correct color space.
For more information, see
the documentation provided with the application or device.
ANikon Software
ViewNX 2 (supplied) and Capture NX 2 (available separately)
automatically select the correct color space when opening photographs
created with this camera.
300
U
“Vignetting” is a drop in brightness at the edges of a photograph.
Vignette control reduces vignetting for type G and D lenses (DX
and PC lenses excluded).
Its effects vary from lens to lens and are
most noticeable at maximum aperture.
Choose from High,
Normal, Low, and Off.
Vignette Control G button ➜Cshooting menu
AVignette Control
Depending on the scene, shooting conditions, and type of lens, TIFF
and JPEG images may exhibit noise (fog) or variations in peripheral
brightness, while custom Picture Controls and preset Picture Controls
that have been modified from default settings may not produce the
desired effect.
Take test shots and view the results in the monitor.
Vignette control does not apply to movies (063), multiple exposures
(0210), or photographs recorded with a DX lens or DX (24 × 16) 1.5 ×
(DX format) selected for image area (085).
301
U
Select On to reduce barrel distortion when
shooting with wide-angle lenses and to
reduce pin-cushion distortion when
shooting with long lenses (note that the
edges of the area visible in the viewfinder
may be cropped out of the final photograph,
and that the time needed to process photographs before
recording begins may increase).
This option does not apply to
movies and is available only with type G and D lenses (PC, fisheye,
and certain other lenses excluded); results are not guaranteed
with other lenses.
Before using auto distortion control with DX
lenses, select On for Auto DX crop or choose an image area of DX
(24×16) 1.5× (085); selecting other options may result in heavily
cropped photographs or in photographs with severe peripheral
distortion.
Auto Distortion Control G button ➜Cshooting menu
ARetouch: Distortion Control
For information on creating copies of existing photographs with
reduced barrel and pin-cushion distortion, see page 377.
302
U
If On is selected, photographs taken at
shutter speeds slower than 1 s will be
processed to reduce noise (bright spots,
randomly-spaced bright pixels, or fog).
The
time required for processing roughly doubles;
during processing, “lm” will flash in the
shutter speed/aperture displays and pictures
can not be taken (if the camera is turned off before processing is
complete, the picture will be saved but noise reduction will not be
performed).
In continuous release mode, frame rates will slow and
while photographs are being processed, the capacity of the
memory buffer will drop.
Photographs taken at high ISO sensitivities can be processed to
reduce noise.
Long Exposure NR
(Long Exposure Noise Reduction)
G button ➜Cshooting menu
High ISO NR G button ➜Cshooting menu
Option Description
High Reduce noise (randomly-spaced bright pixels or fog),
particularly in photographs taken at high ISO sensitivities.
Choose the amount of noise reduction performed from High,
Normal, and Low.
Normal
Low
Off
Noise reduction is performed only at sensitivities of 3200 and
higher.
The amount of noise reduction is less than the amount
performed when Low is selected for High ISO NR.
303
U
ACustom Settings:
Fine-Tuning Camera Settings
To display the Custom Settings menu, press G and select the
A(Custom Settings menu) tab.
Custom Settings are used to customize camera settings to suit
individual preferences.
G button
Custom Setting groups
Main menu
Custom settings
bank (0305)
304
U
The following Custom Settings are available:
Custom Setting 0
Custom settings bank 305
aAutofocus
a1 AF-C priority selection 307
a2 AF-S priority selection 308
a3 Focus tracking with lock-on 309
a4 AF activation 309
a5 Focus point illumination 310
a6 Focus point wrap-around 310
a7 Number of focus points 311
a8 Assign AF-ON button 311
a9 Assign AF-ON button (vert.) 312
a10 Store points by orientation 312
bMetering/exposure
b1 ISO sensitivity step value 313
b2 EV steps for exposure cntrl 313
b3 Exp./flash comp. step value 313
b4 Easy exposure compensation 314
b5 Center-weighted area 315
b6 Fine-tune optimal exposure 315
cTimers/AE lock
c1 Shutter-release button AE-L 316
c2 Standby timer 316
c3 Self-timer 317
c4 Monitor off delay 317
dShooting/display
d1 Beep 318
d2 Shooting speed 318
d3 Max. continuous release 319
d4 Exposure delay mode 319
d5 File number sequence 320
d6 Viewfinder grid display 321
d7 Control panel/viewfinder 321
d8 Screen tips 321
d9 Information display 322
d10 LCD illumination 322
eBracketing/flash
e1 Flash sync speed 323
e2 Flash shutter speed 324
e3 Optional flash 324
e4 Exposure comp. for flash 325
e5 Modeling flash 325
e6 Auto bracketing set 325
e7 Auto bracketing (Mode M) 326
e8 Bracketing order 326
fControls
f1 Multi selector center button 327
f2 Multi selector 328
f3 Assign Fn button 328
f4 Assign preview button 333
f5 Assign sub-selector 333
f6 Assign sub-selector center 333
f7 Assign Fn button (vert.) 334
f8 Shutter spd & aperture lock 334
f9 Assign BKT button 335
f10 Customize command dials 336
f11 Release button to use dial 337
f12 Slot empty release lock 338
f13 Reverse indicators 338
f14 Assign multi selector (vert.) 338
f15 Playback zoom 339
f16 Assign movie record button 339
gMovie
g1 Assign Fn button 340
g2 Assign preview button 341
g3 Assign sub-selector center 342
g4 Assign shutter button 343
Custom Setting 0
305
U
Custom Settings are stored in one of four banks.
Changes to
settings in one bank have no effect on the others.
To store a
particular combination of frequently-used settings, select one of
the four banks and set the camera to these settings.
The new
settings will be stored in the bank even when the camera is turned
off, and will be restored the next time the bank is selected.
Different combinations of settings can be stored in the other
banks, allowing the user to switch instantly from one combination
to another by selecting the appropriate bank from the bank menu.
The default names for the four Custom Settings banks are A, B, C,
and D.
A descriptive caption up to 20 characters long can be added
as described on page 180 by highlighting the menu bank and
pressing 2.
❚❚ Restoring Default Settings
To restore default settings,
highlight a bank in the Custom
settings bank menu and press
O (Q).
A confirmation dialog
will be displayed; highlight Ye s
and press J to restore default
settings for the selected bank
(0414).
Custom Settings Bank G button ➜ACustom Settings menu
O (Q) button
306
U
ACustom Settings Bank
The top control panel and information displays
show the current Custom Settings bank.
ASee Also
Menu defaults are listed on page 414.
If settings in the current bank
have been modified from default values, an asterisk will be displayed
adjacent to the altered settings in the second level of the Custom
Settings menu.
307
U
When AF-C is selected for viewfinder photography (097), this
option controls whether photographs can be taken whenever the
shutter-release button is pressed (release priority) or only when the
camera is in focus (focus priority).
Regardless of the option selected, focus will not lock when AF-C is
selected for autofocus mode. The camera will continue to adjust
focus until the shutter is released.
a: Autofocus
a1: AF-C Priority Selection G button ➜ACustom Settings menu
Option Description
GRelease Photos can be taken whenever the shutter-release
button is pressed.
BFocus +
release
Photos can be taken even when the camera is not in
focus. If the subject is dark or low contrast and the
camera is in continuous mode, priority will be given to
focus for the first shot in each series and to frame rate
for the remaining shots, ensuring a high frame rate if the
distance to the subject does not change during
shooting.
ERelease +
focus
Photos can be taken even when the camera is not in
focus.
In continuous mode, frame rate slows for
improved focus if the subject is dark or low contrast.
FFocus Photos can only be taken when the in-focus indicator
(I) is displayed.
308
U
When AF-S is selected for viewfinder photography (097), this
option controls whether photographs can be taken only when the
camera is in focus (focus priority) or whenever the shutter-release
button is pressed (release priority) in single-servo autofocus.
Regardless of the option selected, if the in-focus indicator (I) is
displayed when AF-S is selected for autofocus mode, focus will lock
while the shutter-release button is pressed halfway.
Focus lock
continues until the shutter is released.
a2: AF-S Priority Selection G button ➜ACustom Settings menu
Option Description
GRelease Photos can be taken whenever the shutter-release
button is pressed.
FFocus Photos can only be taken when the in-focus indicator
(I) is displayed.
309
U
This option controls how autofocus adjusts to sudden large
changes in the distance to the subject when AF-C is selected during
viewfinder photography (097).
If Shutter/AF-ON is selected, both the
shutter-release button and the B button
can be used to initiate autofocus.
If AF-ON
only is selected, autofocus is only initiated
when the B button is pressed.
a3: Focus Tracking with Lock-On
G button ➜ACustom Settings menu
Option Description
C5 (Long) When the distance to the subject changes abruptly, the
camera waits for the specified period before adjusting
the distance to the subject.
This prevents the camera
from refocusing when the subject is briefly obscured by
objects passing through the frame.
(4
D3 (Normal)
)2
E1 (Short)
Off
The camera immediately adjusts focus when the
distance to the subject changes.
Use when
photographing a series of subjects at varying distances
in quick succession.
a4: AF Activation G button ➜ACustom Settings menu
310
U
The options in this menu control whether or not the focus points
are illuminated.
Choose whether focus-point selection “wraps around” from one
edge of the viewfinder to another.
a5: Focus Point Illumination G button ➜ACustom Settings menu
Option Description
Manual focus
mode
Choose On to display the active focus point in manual focus
mode.
Continuous
mode
Choose On to display the active focus point in CH
(continuous high-speed) and CL (continuous low-speed)
modes.
Focus point
brightness
Choose the brightness of the focus point display in the
viewfinder from Extra high, High, Normal, and Low.
Dynamic-area
AF display
Choose On to display both the selected focus point and the
surrounding focus points in dynamic-area AF mode
(0100). When 3D-tracking is used, a dot will be displayed
in the center of the focus point (n).
a6: Focus Point Wrap-Around G button ➜ACustom Settings menu
Option Description
Wrap
Focus-point selection “wraps
around” from top to bottom, bottom
to top, right to left, and left to right,
so that, for example, pressing 2
when a focus point at the right edge of the viewfinder
display is highlighted (q) selects the corresponding focus
point at the left edge of the display (w).
No wrap
The focus-point display is bounded by the outermost focus
points so that, for example, pressing 2 when a focus point
at the right edge of the display is selected has no effect.
q
w
311
U
Choose the number of focus points available for manual focus-
point selection.
Choose the function performed when the
B button is pressed.
a7: Number of Focus Points G button ➜ACustom Settings menu
Option Description
B51 points Choose from the 51 focus points shown at
right.
A11 points Choose from the 11 focus points shown at
right.
Use for quick focus-point selection.
a8: Assign AF-ON Button G button ➜ACustom Settings menu
Option Description
AAF-ON Pressing the B button initiates autofocus.
BAE/AF lock Focus and exposure lock while the B button is
pressed.
CAE lock only Exposure locks while the B button is pressed.
DAE lock (Reset
on release)
Exposure locks when the B button is pressed, and
remains locked until the button is pressed a second
time, the shutter is released, or the standby timer
expires.
EAE lock (Hold)
Exposure locks when the B button is pressed, and
remains locked until the button is pressed a second
time or the standby timer expires.
FAF lock only Focus locks while the B button is pressed.
312
U
Choose the function assigned to the B
button for vertical shooting.
If Yes is selected, separate focus points can be selected for “wide”
(landscape) orientation, for “tall” (portrait) orientation with the
camera rotated 90° clockwise, and for “tall” orientation with the
camera rotated 90° counterclockwise. Select No to use the same
focus point regardless of camera orientation.
a9: Assign AF-ON Button (Vert.) G button ➜ACustom Settings menu
Option Description
GSame as AF-ON
button
Both B buttons perform the function selected
for Custom Setting a8.
AAF-ON Pressing the vertical B button initiates
autofocus.
BAE/AF lock Focus and exposure lock while the vertical B
button is pressed.
CAE lock only Exposure locks while the vertical B button is
pressed.
DAE lock (Reset on
release)
Exposure locks when the vertical B button is
pressed, and remains locked until the button is
pressed a second time, the shutter is released, or
the standby timer expires.
EAE lock (Hold)
Exposure locks when the vertical B button is
pressed, and remains locked until the button is
pressed a second time or the standby timer
expires.
FAF lock only Focus locks while the vertical B button is
pressed.
a10: Store Points by Orientation G button ➜ACustom Settings menu
313
U
Select the increments used when making
adjustments to ISO sensitivity (0117). If
possible, the current ISO sensitivity setting is
maintained when the step value is changed. If
the current ISO sensitivity setting is not
available at the new step value, ISO sensitivity
will be rounded to the nearest available setting.
Select the increments used when making
adjustments to shutter speed, aperture, and
bracketing.
Select the increments used when making
adjustments to exposure and flash
compensation.
b: Metering/Exposure
b1: ISO Sensitivity Step Value G button ➜ACustom Settings menu
b2: EV Steps for Exposure Cntrl G button ➜ACustom Settings menu
b3: Exp./Flash Comp. Step Value
G button ➜ACustom Settings menu
314
U
This option controls whether the E button is needed to set
exposure compensation (0137).
If On (Auto reset) or On is
selected, the 0 at the center of the exposure display will flash even
when exposure compensation is set to ±0.
b4:
Easy Exposure Compensation
G button ➜ACustom Settings menu
Option Description
On (Auto reset)
Exposure compensation is set by rotating one of the
command dials (see note below). The setting selected
using the command dial is reset when the camera turns off
or the standby timer expires (exposure compensation
settings selected using the E button are not reset).
On
As above, except that the exposure compensation value
selected using the command dial is not reset when the
camera turns off or the standby timer expires.
Off Exposure compensation is set by pressing the E button
and rotating the main command dial.
AChange Main/Sub
The dial used to set exposure compensation when On (Auto reset) or
On is selected for Custom Setting b4 (Easy exposure compensation)
depends on the option selected for Custom Setting f10 (Customize
command dials)> Change main/sub (0336).
Customize command dials > Change main/sub
Off On
Exposure
mode
eSub-command dial Sub-command dial
fSub-command dial Main command dial
gMain command dial Sub-command dial
hN/A
315
U
When calculating exposure, center-weighted
metering assigns the greatest weight to a
circle in the center of the frame.
The diameter
(φ) of this circle can be set to 8, 12, 15, or
20 mm or to the average of the entire frame.
Note that unless Average is selected, the diameter is fixed at
12 mm when a non-CPU lens is used, regardless of the setting
selected for Non-CPU lens data in the setup menu (0228). When
Average is selected, the average of the entire frame will be used for
both CPU and non-CPU lenses.
Use this option to fine-tune the exposure
value selected by the camera.
Exposure can
be fine-tuned separately for each metering
method by from +1 to –1 EV in steps of 1/6EV.
b5: Center-Weighted Area G button ➜ACustom Settings menu
b6:
Fine-Tun
e O
ptimal Exposure
G button ➜ACustom Settings menu
DFine-Tuning Exposure
Exposure can be fine-tuned separately for each Custom Settings bank
and is not affected by two-button resets.
Note that as the exposure
compensation (E) icon is not displayed, the only way to determine how
much exposure has been altered is to view the amount in the fine-
tuning menu.
Exposure compensation (0137) is preferred in most
situations.
316
U
If On is selected, exposure will lock when the
shutter-release button is pressed halfway.
Choose how long the camera continues to
meter exposure when no operations are
performed. The shutter-speed and aperture
displays in the top control panel and
viewfinder turn off automatically when the
standby timer expires.
Choose a shorter standby timer delay for longer battery life.
c: Timers/AE Lock
c1: Shutter-Release Button AE-L G button ➜ACustom Settings menu
c2: Standby Timer G button ➜ACustom Settings menu
317
U
Choose the length of the shutter release delay, the number of shots
taken, and the interval between shots in self-timer mode.
•Self-timer delay: Choose the length of the
shutter-release delay.
•Number of shots: Press 1 and 3 to choose the
number of shots taken each time the
shutter-release button is pressed.
•Interval between shots: Choose the interval
between shots when the Number of shots
is more than 1.
Choose how long the monitor remains on
when no operations are performed during
playback (Playback; defaults to 10 s) and
image review (Image review; defaults to 4 s),
when menus (Menus; defaults to 20 s) or
information (Information display; defaults to
10 s) are displayed, or during live view and movie recording (Live
view; defaults to 10 minutes).
Choose a shorter monitor-off delay
for longer battery life.
c3: Self-Timer G button ➜ACustom Settings menu
c4: Monitor off Delay G button ➜ACustom Settings menu
318
U
Choose the pitch and volume of the beep that sounds when the
camera focuses using single-servo autofocus (097), when focus
locks during live view photography, or while the release timer is
counting down in self-timer mode (0114), or when time-lapse
photography ends (0223).
Note that regardless of the option
selected, a beep will not sound in movie live view (063), or quiet-
shutter release mode (mode J; 0111), or if Silent is selected
during live view photography.
•Volume: Choose 3 (high), 2 (medium), 1 (low)
or Off (mute).
When an option other than
Off is selected, c appears in the top control
panel and information display.
•Pitch: Choose High or Low.
Choose the maximum frame advance rate for CH (continuous high-
speed) and CL (continuous low-speed) modes. For more
information on frame rate, see page 112.
d: Shooting/Display
d1: Beep G button ➜ACustom Settings menu
d2: Shooting Speed G button ➜ACustom Settings menu
Option Description
Continuous
high-speed
Choose the frame advance rate for CH (continuous high-
speed) mode from 10 and 11 fps.
Continuous
low-speed
Choose the frame advance rate for CL (continuous low-
speed) mode from values between 1 and 10 fps.
319
U
The maximum number of shots that can be taken in a single burst
in continuous mode can be set to any value between 1 and 200.
In situations where the slightest camera
movement can blur pictures, select
1 s
,
2 s
, or
3s
to delay shutter release until one, two, or
three seconds after the mirror is raised.
Exposure delay is not available when
Silent
is
selected for
Live view photography
in the
shooting menu (
0
60).
d3: Max.
Continuous Release G button ➜ACustom Settings menu
AThe Memory Buffer
Regardless of the option selected for Custom Setting d3, shooting will
slow when the memory buffer fills (t00).
See page 444 for more
information on the capacity of the memory buffer.
d4: Exposure Delay Mode G button ➜ACustom Settings menu
320
U
When a photograph is taken, the camera
names the file by adding one to the last file
number used.
This option controls whether
file numbering continues from the last
number used when a new folder is created,
the memory card is formatted, or a new
memory card is inserted in the camera.
d5: File Number Sequence G button ➜ACustom Settings menu
Option Description
On
When a new folder is created, the memory card formatted,
or a new memory card inserted in the camera, file
numbering continues from the last number used or from
the largest file number in the current folder, whichever is
higher.
If a photograph is taken when the current folder
contains a photograph numbered 9999, a new folder will be
created automatically and file numbering will begin again
from 0001.
Off
File numbering is reset to 0001 when a new folder is
created, the memory card is formatted, or a new memory
card is inserted in the camera.
Note that a new folder is
created automatically if a photograph is taken when the
current folder contains 999 photographs.
Reset
As for On, except that the next photograph taken is
assigned a file number by adding one to the largest file
number in the current folder.
If the folder is empty, file
numbering is reset to 0001.
DFile Number Sequence
If the current folder is numbered 999 and contains either 999
photographs or a photograph numbered 9999, the shutter-release
button will be disabled and no further photographs can be taken.
Choose Reset for Custom Setting d5 (File number sequence) and then
either format the current memory card or insert a new memory card.
321
U
Choose On to display on-demand grid lines in
the viewfinder for reference when composing
photographs (011).
Choose the information displayed in the viewfinder and rear
control panel.
Choose On to display tool tips for items
selected in the information display (016).
d6: Viewfinder Grid Display G button ➜ACustom Settings menu
d7: Control Panel/Viewfinder G button ➜ACustom Settings menu
Option Description
Rear control
panel
Choose from ISO sensitivity (9) and Exposures
remaining (k). If Exposures remaining is selected, ISO
sensitivity will only be displayed while the S button is
pressed.
Viewfinder
display
Choose from Frame count (l) and Exposures
remaining (k). Note that regardless of the option
selected, memory buffer capacity will be shown while
the shutter-release button is pressed.
d8: Screen Tips G button ➜ACustom Settings menu
322
U
If Auto (AUTO) is selected, the color of the lettering in the
information display (013) will automatically change from black to
white or white to black to maintain contrast with the background.
To always use the same color lettering, select Manual and choose
Dark on light (B; black lettering) or Light on dark (W; white
lettering).
Monitor brightness will automatically be adjusted for
maximum contrast with the selected text color.
If
Off
is selected, the control panel and button
backlights (illuminators) will only light while
the power switch is rotated toward
D
. If
On
is
selected, the backlights will remain on while
the standby timer is active (
0
45; note that
regardless of the option selected, the
backlights turn off while the shutter-release button is pressed).
Select
Off
for increased battery life.
d9: Information Display G button ➜ACustom Settings menu
Dark on light Light on dark
d10: LCD Illumination G button ➜ACustom Settings menu
AButton Backlights
The following controls are equipped with backlights: the D, M, Y, G,
L (Z/Q), X, W, J, R, a, H, U, T, and S buttons and the
release mode dial.
323
U
This option controls flash sync speed.
e: Bracketing/Flash
e1: Flash Sync Speed G button ➜ACustom Settings menu
Option Description
1/250 s
(Auto FP)
Use auto FP high-speed sync when a compatible flash unit
is attached (
0
193). If other flash units are used, shutter
speed is set to
1
/
250
s. When the camera shows a shutter
speed of
1
/
250
s in exposure mode
e
or
g
, auto FP high-
speed sync will be activated if the actual shutter speed is
faster than
1
/
250
s.
1/250 s–1/60 s Flash sync speed set to selected value.
AFixing Shutter Speed at the Flash Sync Speed Limit
To fix shutter speed at the sync speed limit in shutter-priority auto or
manual exposure modes, select the next shutter speed after the slowest
possible shutter speed (30 s or bulb).
An X (flash sync indicator) will be
displayed in the viewfinder and top control panel.
AAuto FP High-Speed Sync
Allows the flash to be used at the highest shutter speed supported by
the camera, making it possible to choose the maximum aperture for
reduced depth of field even when the subject is backlit in bright
sunlight. The information display flash mode indicator shows “FP”
when auto FP high-speed sync is active (0197).
324
U
This option determines the slowest shutter
speed available when using front- or rear-
curtain sync or red-eye reduction in
programmed auto or aperture-priority auto
exposure modes (regardless of the setting
chosen, shutter speeds can be as slow as 30 s
in shutter-priority auto and manual exposure modes or at flash
settings of slow sync, slow rear-curtain sync, or red-eye reduction
with slow sync).
Options range from 1/60 s (1/60 s) to 30 s (30 s).
Choose a flash control mode for optional SB-400 flash units.
e2: Flash Shutter Speed G button ➜ACustom Settings menu
e3: Optional Flash G button ➜ACustom Settings menu
Option Description
rTTL Flash output is adjusted automatically in response to
shooting conditions (0198).
sManual Choose a flash level between Full and 1/128 (1/128 of full
power). Monitor pre-flashes are not emitted.
AFlash Control Mode
The flash control mode is shown in the
information display (014, 197).
325
U
Choose how the camera adjusts flash level when exposure
compensation is used.
If On is selected when the camera is used with
an optional flash unit that supports the Nikon
Creative Lighting system (0192), a modeling
flash will be emitted when the camera Pv
button is pressed (0125).
No modeling flash
is emitted if Off is selected.
Choose the setting or settings bracketed when auto bracketing
(0139) is in effect.
Choose AE & flash (j) to perform both
exposure and flash-level bracketing, AE only (k) to bracket only
exposure, Flash only (l) to perform only flash-level bracketing, WB
bracketing (m) to perform white balance bracketing (0145), or
ADL bracketing (y) to perform bracketing using Active
D-Lighting (0149).
Note that white balance bracketing is not
available at image quality settings of NEF (RAW) or
NEF (RAW) + JPEG.
e4: Exposure Comp. for Flash G button ➜ACustom Settings menu
Option Description
YE Entire frame Both flash level and exposure compensation are
adjusted to modify exposure over the entire frame.
EBackground
only Exposure compensation applies to background only.
e5: Modeling Flash G button ➜ACustom Settings menu
e6: Auto Bracketing Set G button ➜ACustom Settings menu
326
U
This option determines which settings are affected when AE &
flash or AE only is selected for Custom Setting e6 in manual
exposure mode.
Flash bracketing is performed only with i-TTL or AA flash control.
If
a setting other than Flash only is selected and the flash is not used,
ISO sensitivity will be fixed at the value for the first shot, regardless
of the setting selected for auto ISO sensitivity control (0119).
At the default setting of MTR>under>over (H), exposure, flash,
and white balance bracketing are performed in the order
described on pages 142 and 146.
If Under>MTR>over (I) is
selected, shooting will proceed in order from the lowest to the
highest value.
This setting has no effect on ADL bracketing.
e7: Auto Bracketing (Mode M) G button ➜ACustom Settings menu
Option Description
FFlash/speed
Camera varies shutter speed (Custom Setting e6
set to AE only) or shutter speed and flash level
(Custom Setting e6 set to AE & flash).
GFlash/speed/
aperture
Camera varies shutter speed and aperture (Custom
Setting e6 set to AE only) or shutter speed,
aperture, and flash level (Custom Setting e6 set to
AE & flash).
HFlash/aperture
Camera varies aperture (Custom Setting e6 set to
AE only) or aperture and flash level (Custom
Setting e6 set to AE & flash).
IFlash only Camera varies flash level only (Custom Setting e6
set to AE & flash).
e8: Bracketing Order G button ➜ACustom Settings menu
327
U
This option determines the role assigned to the center of the multi
selector during viewfinder photography, playback, and live view
(regardless of the option selected, pressing the center of the multi
selector when a movie is displayed full frame starts movie
playback).
❚❚ Shooting Mode
❚❚ Playback Mode
f: Controls
f1: Multi Selector Center Button G button ➜ACustom Settings menu
Option Role assigned to center of multi selector
JSelect center focus point Select center focus point.
Not used None.
Option Role assigned to center of multi selector
nThumbnail on/off Toggle between full-frame and thumbnail playback.
oView histograms
In both full-frame and thumbnail playback,
a histogram is displayed while the center of the
multi selector is pressed.
pZoom on/off
Toggle between full-frame or thumbnail playback
and playback zoom.
Choose the initial zoom setting
from Low magnification, Medium magnification,
and High magnification.
The zoom display will
center on the active focus point.
uChoose slot and
folder Display the slot and folder selection dialog (0236).
328
U
❚❚ Live View
If Restart standby timer is selected,
operating the multi selector when the
standby timer expires (045) will activate the
meters and start the standby timer.
If Do
nothing is selected, the timer will not start
when the multi selector is pressed.
Choose the role played by the Fn button,
either by itself (Press) or when used in
combination with the command dials
(Press + command dials).
Option Role assigned to center of multi selector
JSelect center
focus point
Pressing the center of the multi selector in live view
selects the center focus point.
pZoom on/off
Press the center of the multi selector to toggle zoom
on and off.
Choose the initial zoom setting from
Low magnification, Medium magnification, and
High magnification. The zoom display will center
on the active focus point.
Not used Pressing the center of the multi selector has no
effect in live view.
f2: Multi Selector G button ➜ACustom Settings menu
f3: Assign Fn Button G button ➜ACustom Settings menu
329
U
❚❚ Press
Selecting Press displays the following options:
Option Description
qPreview*Press the Fn button to preview depth of field (0125).
rFV lock*Press the Fn button to lock flash value (supported flash
units only, 0192).
Press again to cancel FV lock.
BAE/AF lock Focus and exposure lock while the Fn button is pressed.
CAE lock only Exposure locks while the Fn button is pressed.
D
AE lock
(Reset on
release)*
Exposure locks when the Fn button is pressed, and
remains locked until the button is pressed a second
time, the shutter is released, or the standby timer
expires.
EAE lock
(Hold)*
Exposure locks when the Fn button is pressed, and
remains locked until the button is pressed a second
time or the standby timer expires.
FAF lock only Focus locks while the Fn button is pressed.
AAF-ON*Pressing the Fn button initiates autofocus.
sFlash off The flash will not fire in photos taken while the Fn
button is pressed.
1Bracketing
burst
If the Fn button is pressed while exposure, flash, or ADL
bracketing is active in single frame or quiet shutter-
release mode, all shots in the current bracketing
program will be taken each time the shutter-release
button is pressed.
If white balance bracketing is active
or continuous release mode (mode CH or CL) is selected,
the camera will repeat the bracketing burst while the
shutter-release button is held down.
LMatrix
metering
Matrix metering is activated while the Fn button is
pressed.
M
Center-
weighted
metering
Center-weighted metering is activated while the Fn
button is pressed.
NSpot
metering
Spot metering is activated while the Fn button is
pressed.
330
U
KPlayback *
Fn button performs same function as K button.
Select
when using a telephoto lens or in other circumstances
in which it is difficult to operate the K button with
your left hand.
%MY MENU*Pressing the Fn button displays “MY MENU”.
3
Access top
item in MY
MENU *
Press the Fn button to jump to the top item in “MY
MENU.” Select this option for quick access to a
frequently-used menu item.
!
Viewfinder
virtual
horizon *
Press the Fn button to view a virtual horizon display in
the viewfinder (see below).
None No operation is performed when the Fn button is
pressed.
* This option can not be used in combination with Press + command dials
(0332).
Selecting this option displays a message and sets Press +
command dials to None.
If another option is selected for Press +
command dials while this setting is active, Press will be set to None.
Option Description
331
U
AVirtual Horizon
When Viewfinder virtual horizon is selected for f3 (Assign Fn
button)> Press, pressing the Fn button displays a pitch and roll
indicators in the viewfinder.
Press the button a second time to clear the
indicators from display.
Roll
Camera tilted right Camera level Camera tilted left
Pitch
Camera tilted forward Camera level Camera tilted back
The roles of the pitch and roll indicators are reversed when the camera
is rotated to take pictures in “tall” (portrait) orientation. Note that the
display may not be accurate when the camera is tilted at a sharp angle
forward or back. If the camera is unable to measure tilt, the amount of
tilt will not be displayed.
332
U
❚❚ Press + command dials
Selecting Press + command dials displays the following options:
Option Description
iChoose
image area
Press the Fn button and
rotate a command dial to
choose from pre-selected
image areas (085).
Selecting Choose image
area displays a list of image
areas; highlight options and
press 2 to select or deselect, then highlight Done
and press J.
$
Shutter spd
& aperture
lock
Press the Fn button and rotate the main command
dial to lock shutter speed in modes f and h; press the
Fn button and rotate the sub-command dial to lock
aperture in modes g and h. See page 133 for more
information.
v1 step spd/
aperture
If the Fn button is pressed when the command dials
are rotated, changes to shutter speed (exposure
modes f and h) and aperture (exposure modes g and
h) are made in increments of 1 EV, regardless of the
option selected for Custom Setting b2 (EV steps for
exposure cntrl, 0313).
w
Choose non-
CPU lens
number
Press the Fn button and rotate a command dial to
choose a lens number specified using the Non-CPU
lens data option (0228).
yActive
D-Lighting
Press the Fn button and rotate the command dials to
adjust Active D-Lighting (0184).
nShooting
menu bank
If this option is selected, the shooting menu bank can
be selected by pressing the Fn button and rotating a
command dial.
None No operation is performed when the command dials
are rotated while the Fn button is pressed.
333
U
Choose the role played by the Pv button,
either by itself (Press) or when used in
combination with the command dials
(Press + command dials).
The options
available are the same as for Assign Fn
button (0328), except that AF-ON is not
available for Press. The default options for Press and Press +
command dials are Preview and None, respectively.
Choose whether the sub-selector 1, 3, 4,
and 2 controls are used for focus point
selection (Focus point selection; 0103) or
perform the same role as the matching
controls on the multi selector (Same as multi
selector).
Choose the role played by the center of the
sub-selector, either by itself (Press) or when
used in combination with the command dials
(Press + command dials).
The options
available are the same as for Assign Fn
button (0328), except that Press has an
additional Select center focus point option that allows the center
of the sub-selector to be used to select the center focus point and
that AF-ON, 1 stp spd/aperture, and Active D-Lighting are not
available. The default options for Press and Press + command
dials are AE/AF lock and None, respectively.
f4: Assign Preview Button G button ➜ACustom Settings menu
f5: Assign Sub-selector G button ➜ACustom Settings menu
f6: Assign Sub-selector Center G button ➜ACustom Settings menu
334
U
Choose the role played by the Fn
button for vertical shooting, either
by itself (Press) or when used in
combination with the command
dials (Press + command dials).
The
options available are the same as for
Assign Fn button (0328), except that AF-ON is not available for
Press and that Press + command dials has additional ISO
sensitivity, Exposure mode, Exposure compensation, and
Metering options that allow the Fn button for vertical shooting
and command dials to be used to select ISO sensitivity (0117),
exposure mode (0125), exposure compensation (0137), or
metering (0123), respectively. The default options for Press and
Press + command dials are respectively AE/AF lock and None.
Selecting On for Shutter speed lock locks
shutter speed at the value currently selected
in mode f or h. Selecting On for Aperture
lock locks aperture at the value currently
selected in mode g or h. Shutter speed and
aperture lock are not available in mode e.
f7: Assign Fn Button (Vert.) G button ➜ACustom Settings menu
f8: Shutter Spd & Aperture Lock G button ➜ACustom Settings menu
335
U
Choose the role played by the D button. If
high dynamic range or multiple exposure is
active while another function is assigned to
the D button, the D button can not be
used until high dynamic range or multiple
exposure photography ends.
f9: Assign BKT Button G button ➜ACustom Settings menu
Option Description
tAuto
bracketing
Press the t button and rotate a command dial to
choose the bracketing increment and number of shots
in the bracketing sequence (0139).
$Multiple
exposure
Press the t button and rotate a command dial to
choose the mode and number of shots for multiple
exposures (0212).
2
HDR (high
dynamic
range)
Press the t button and rotate a command dial to
choose the mode and the exposure differential
(0190).
336
U
This option controls the operation of the main and sub-command
dials.
f10: Customize Command Dials G button ➜ACustom Settings menu
Option Description
Reverse
rotation
Reverse the direction of rotation of the
command dials when they are used to
make adjustments to Exposure
compensation and/or Shutter speed/
aperture.
Highlight options and press
2 to select or deselect, then highlight
Done and press J.
This setting also
applies to the command dials for vertical shooting.
Change
main/sub
If Off is selected, the main command
dial controls shutter speed and the sub-
command dial controls aperture.
If On
is selected, the main command dial will
control aperture and the sub-command
dial shutter speed.
If On (Mode A) is
selected, the main command dial will
be used to set aperture in exposure mode g only.
This setting
also applies to the command dials for vertical shooting.
Aperture
setting
If Sub-command dial is selected, aperture can only be
adjusted with the sub-command dial (or with the main
command dial if On is selected for Change main/sub).
If
Aperture ring is selected, aperture can only be adjusted with
the lens aperture ring and the camera aperture display will
show aperture in increments of 1 EV (aperture for type G lenses
is still set using the sub-command dial).
Note that regardless of
the setting chosen, the aperture ring must be used to adjust
aperture when a non-CPU lens is attached.
337
U
Selecting Yes allows adjustments that are normally made by
holding the I (Q), E, D, M, Y, S, T, U, or AF-mode
button and rotating a command dial to be made by rotating the
command dial after the button is released (this also applies to the
Fn and Pv buttons and the Fn button for vertical shooting, if they
have been assigned Active D-Lighting using Custom Setting f3,
Assign Fn button; 0328, Custom Setting f4, Assign preview
button; 0333, or Custom Setting f7, Assign Fn button (vert.);
0334).
Setting ends when any of the affected buttons is pressed
again or the shutter-release button is pressed halfway.
Except
when No limit is selected for Custom Setting c2 Standby timer,
setting will also end when the standby timer expires.
Menus
and
playback
If Off is selected, the multi selector is used to choose the
picture displayed during full-frame playback, highlight
thumbnails, and navigate menus.
If On or On (image review
excluded) is selected, the main command dial can be used to
choose the picture displayed during full-frame playback, move
the cursor left or right during thumbnail playback, and move
the menu highlight bar up or down.
The sub-command dial is
used to display additional photo information in full-frame
playback and to move the cursor up or down during thumbnail
playback.
Select On (image review excluded) to prevent the
command dials from being used for playback during image
review. While menus are displayed, rotating the sub-
command dial right displays the sub-menu for the selected
option, while rotating it left displays the previous menu.
To
make a selection, press 2, the center of the multi selector, or
J.
f11: Release Button to Use Dial G button ➜ACustom Settings menu
Option Description
338
U
Selecting Enable release allows the shutter to be released when
no memory card is inserted, although no pictures will be recorded
(they will however be displayed in the monitor in demo mode).
If
Release locked is selected, the shutter-release button is only
enabled when a memory card is inserted in the camera.
If (V) is selected, the exposure indicators in the
top control panel and information display are displayed with
positive values on the left and negative values on the right.
Select
(W) to display negative values on the left and
positive values on the right.
Choose whether the 1, 3, 4, and 2 controls on the multi selector
for vertical shooting are used for focus point selection (Focus
point selection; 0103) or perform the same role as the matching
controls on the multi selector (Same as multi selector; note that in
this case, you can select Info42/Playback13 for Photo info
playback to reverse the role of the buttons so that pressing 1 or 3
displays additional images and pressing 4 or 2 changes the photo
information displayed). The role played by the center of the multi
selector for vertical shooting when Focus point selection is
chosen is that selected for Custom Setting f6 (Assign sub-selector
center, 0333) > Press.
f12: Slot Empty Release Lock G button ➜ACustom Settings menu
f13: Reverse Indicators G button ➜ACustom Settings menu
f14: Assign Multi Selector (Vert.) G button ➜ACustom Settings menu
339
U
Choose the controls used for playback zoom.
Choose the role played by the movie-record button when C is
selected with the live view selector.
f15: Playback Zoom G button ➜ACustom Settings menu
Option Description
uUse X and WPress X to zoom in, W to zoom out.
vUse X/W + y
Press either X or W and rotate the main command
dial right to zoom in, left to zoom out.
Pressing
either button without rotating the command dial
has no effect.
f16: Assign Movie Record Button G button ➜ACustom Settings menu
Option Description
9ISO sensitivity Press the button and rotate a command dial to
choose an ISO sensitivity (0117).
iChoose image
area
Press the button and rotate a command dial to
choose the image area (085).
nShooting menu
bank
The shooting menu bank can be selected by pressing
the button and rotating a command dial (0294).
$Shutter spd &
aperture lock
Press the button and rotate the main command dial
to lock shutter speed in modes f and h; press the
button and rotate the sub-command dial to lock
aperture in modes g and h. See page 133 for more
information.
None No operation is performed if the command dials are
rotated while the button is pressed.
340
U
Choose the role played by the Fn button during movie live view.
g: Movie
g1: Assign Fn Button G button ➜ACustom Settings menu
Option Description
tPower aperture
(open)
Aperture widens while the button is pressed. Use in
combination with Custom Setting g2 (Assign
preview button)> Power aperture (close) for
button-controlled aperture adjustment.
rIndex marking
Press the button during movie recording to add an
index at the current position (067). Indices can be
used when viewing and editing movies.
sView photo
shooting info
Press the button to display information on shutter
speed, aperture, and other photo settings in place of
movie recording information.
Press again to return
to the movie recording display.
None Pressing the button has no effect.
341
U
Choose the role played by the Pv button during movie live view.
g2: Assign Preview Button G button ➜ACustom Settings menu
Option Description
qPower aperture
(close)
Aperture narrows while the button is pressed. Use in
combination with Custom Setting g1 (Assign Fn
button)> Power aperture (open) for button-
controlled aperture adjustment.
rIndex marking
Press the button during movie recording to add an
index at the current position (067). Indices can be
used when viewing and editing movies.
sView photo
shooting info
Press the button to display information on shutter
speed, aperture, and other photo settings in place of
movie recording information. Press again to return
to the movie recording display.
None Pressing the button has no effect.
APower Aperture
Power aperture is available only in exposure modes g and h and can not
be used during movie recording or while photo shooting info is
displayed (A 6 icon indicates that power aperture can not be used).
The display may flicker while aperture is adjusted.
342
U
Choose the role played by the center of the sub-selector during
movie live view.
g3: Assign Sub-selector Center G button ➜ACustom Settings menu
Option Description
rIndex marking
Press the control during movie recording to add an
index at the current position (067). Indices can be
used when viewing and editing movies.
sView shooting
photo info
Press the control to display information on shutter
speed, aperture, and other photo settings in place of
movie recording information.
Press again to return to
the movie recording display.
BAE/AF lock Focus and exposure lock while the control is pressed.
CAE lock only Exposure locks while the control is pressed.
EAE lock (Hold)
Exposure locks when the control is pressed, and
remains locked until the control is pressed a second
time or the standby timer expires.
FAF lock only Focus locks while the control is pressed.
None Pressing the control has no effect.
343
U
Choose the role played by pressing the shutter-release button
when 1 is selected with the live view selector.
g4: Assign Shutter Button G button ➜ACustom Settings menu
Option Description
CTake photos
Press the shutter-release button all the way down to
end movie recording and take a photograph with an
aspect ratio that matches that of a movie frame (for
information on image size, see page 71).
1Record movies
Press the shutter-release button halfway to start
movie live view. You can then press the shutter-
release button halfway to focus and press it all the
way down to start or end recording. To end movie
live view, press the a button.
The shutter-release
buttons on optional remote cords (0394) function
in the same way as the camera shutter-release
button.
xLive frame grab
If the shutter-release button is pressed all the way
down during movie recording, the camera will
record a photograph without interrupting movie
recording. Photos are 1,920 × 1,080 pixels in size
(aspect ratio 16 : 9) and recorded at an image quality
of JPEG fine.
Note that during movie recording,
photos are taken one at a time regardless of the
release mode selected; this restriction does not
apply if movie recording is not currently in progress.
ARecord Movies
When this option is selected, interval timer photography (0216) is not
available and any functions assigned to the shutter release button (such
as taking photographs, measuring preset white balance, and taking
image dust-off reference photos) can not be used when 1 is selected
with the live view selector. Select Take photos or Live frame grab to
use these options.
344
U
BThe Setup Menu: Camera Setup
To display the setup menu, press G and select the B (setup
menu) tab.
* Not available when battery is low.
G button
Option 0
Format memory card 345
Monitor brightness 345
Clean image sensor 399
Lock mirror up for cleaning *402
Image Dust Off ref photo 346
HDMI 281
Flicker reduction 348
Time zone and date 348
Language 349
Auto image rotation 350
Battery info 351
Network 269
Image comment 352
Copyright information 353
IPTC 354
Voice memo options 255
Save/load settings 356
GPS 233
Virtual horizon 358
Non-CPU lens data 229
AF fine-tune 359
Firmware version 360
Option 0
ASee Also
Menu defaults are listed on page 417.
DNetwork > Network Connection
Clean image sensor and firmware updates are not available when
Enable is selected for Network > Network connection.
345
U
To begin formatting, choose a memory card
slot and select Ye s.
Note that formatting
permanently deletes all pictures and other data
on the card in the selected slot.
Before
formatting, be sure to make backup copies as
required.
Adjust the brightness of the monitor for playback, menus, and the
information display.
Format Memory Card G button ➜Bsetup menu
DDuring Formatting
Do not turn the camera off or remove memory cards during formatting.
ATwo-Button Format
Memory cards can also be formatted by pressing the O (Q) and I
(Q) buttons for more than two seconds (036).
Monitor Brightness G button ➜Bsetup menu
Option Description
Auto
When the monitor is on, monitor brightness is automatically
adjusted according to ambient lighting conditions. Care should
be taken not to cover the ambient brightness sensor (06).
Manual
Press 1 or 3 to choose monitor brightness.
Choose higher
values for increased brightness, lower values for reduced
brightness.
ASee Also
For information on adjusting monitor brightness in live view, see
page 57.
346
U
Acquire reference data for the Image Dust Off option in
Capture NX 2 (available separately; for more information, see the
Capture NX 2 manual).
Image Dust Off ref photo is available only when a CPU lens is
mounted on the camera.
A non-DX lens with a focal length of at
least 50 mm is recommended.
When using a zoom lens, zoom all
the way in.
1Choose a start option.
Highlight one of the
following options and
press J.
To exit without
acquiring image dust off
data, press G.
•Start: The message
shown at right will be displayed and
“rEF” will appear in the viewfinder and
control panel displays.
•Clean sensor and then start: Select this
option to clean the image sensor
before starting.
The message shown at
right will be displayed and “rEF” will
appear in the viewfinder and control
panel displays when cleaning is
complete.
Image Dust Off Ref Photo G button ➜Bsetup menu
J button
347
U
2Frame a featureless white object in the viewfinder.
With the lens about ten centimeters (four inches) from a well-
lit, featureless white object, frame the object so that it fills the
viewfinder and then press the shutter-release button halfway.
In autofocus mode, focus will automatically be set to infinity;
in manual focus mode, set focus to infinity manually.
3Acquire dust off reference data.
Press the shutter-release button the rest of the way down to
acquire Image Dust Off reference data.
The monitor turns off
when the shutter-release button is pressed.
If the reference object is too bright or too
dark, the camera may be unable to
acquire Image Dust Off reference data
and the message shown at right will be
displayed.
Choose another reference
object and repeat the process from
Step 1.
DImage Sensor Cleaning
Dust off reference data recorded before image sensor cleaning is
performed can not be used with photographs taken after image sensor
cleaning is performed.
Select Clean sensor and then start only if the
dust off reference data will not be used with existing photographs.
DImage Dust Off Reference Data
The same reference data can be used for
photographs taken with different lenses or at
different apertures.
Reference images can not
be viewed using computer imaging software.
A grid pattern is displayed when reference
images are viewed on the camera.
348
U
Reduce flicker and banding when shooting
under fluorescent or mercury-vapor lighting
during live view or movie recording.
Choose
Auto to allow the camera to automatically
choose the correct frequency, or manually
match the frequency to that of the local AC
power supply.
Change time zones, set the camera clock, choose the date display
order, and turn daylight saving time on or off (031).
B flashes in the top control panel when the clock is not set.
Flicker Reduction G button ➜Bsetup menu
DFlicker Reduction
If
Auto
fails to produce the desired results and you are unsure as to the
frequency of the local power supply, test both the 50 and 60 Hz options
and choose the one that produces the best results.
Flicker reduction
may not produce the desired results if the subject is very bright, in which
case you should try choosing a smaller aperture (higher f-number).
To
prevent flicker, select mode
h
and choose a shutter speed adapted to the
frequency of the local power supply:
1
/
125
s,
1
/
60
s, or
1
/
30
s for 60 Hz;
1
/
100
s,
1
/
50
s, or
1
/
25
s for 50 Hz.
Time Zone and Date G button ➜Bsetup menu
Option Description
Time zone Choose a time zone.
The camera clock is automatically set
to the time in the new time zone.
Date and time Set the camera clock.
Date format Choose the order in which the day, month, and year are
displayed.
Daylight
saving time
Turn daylight saving time on or off.
The camera clock will
automatically be advanced or set back one hour.
The
default setting is Off.
349
U
Choose a language for camera menus and messages.
The
following options are available.
Language G button ➜Bsetup menu
Czech
Danish
German
English
Spanish
French
Indonesian
Italian
Dutch
Norwegian
Polish
Portuguese
Čeština
Dansk
Deutsch
En
g
lish
Es
p
añol
Fran
ç
ais
Indonesia
Italiano
Nederlands
Nors
k
Polski
Portu
g
uês
Russian
Romanian
Finnish
Swedish
Turkish
Ukrainian
Arabic
Traditional Chinese
Simplified Chinese
Japanese
Korean
Thai
Р
у
сский
Română
Suomi
Svenska
Türk
ç
e
У
к
р
аїнська
350
U
Photographs taken while On is selected contain information on
camera orientation, allowing them to be rotated automatically
during playback (0290) or when viewed in ViewNX 2 (supplied)
or in Capture NX 2 (available separately; 0393).
The following
orientations are recorded:
Camera orientation is not recorded when Off is selected.
Choose
this option when panning or taking photographs with the lens
pointing up or down.
Auto Image Rotation G button ➜Bsetup menu
Landscape (wide)
orientation
Camera rotated 90°
clockwise
Camera rotated 90°
counter-clockwise
ARotate Tall
To automatically rotate “tall” (portrait-orientation) photographs for
display during playback, select On for the Rotate tall option in the
playback menu (0290).
351
U
View information on the battery currently
inserted in the camera.
Battery Info G button ➜Bsetup menu
Item Description
Charge The current battery level expressed as a percentage.
No. of
shots
The number of times the shutter has been released with the
current battery since the battery was last charged. Note that
the camera may sometimes release the shutter without
recording a photograph, for example when measuring preset
white balance.
Calibration
•j: Due to repeated use and recharging, calibration is
required to ensure that battery level can be measured
accurately; recalibrate battery before charging (0440).
•—: Calibration not required.
Battery
age
A five-level display showing battery age.
0 (k) indicates that
battery performance is unimpaired, 4 (l) that the battery has
reached the end of its charging life and should be replaced.
Note that fresh batteries charged at temperatures under
about 5 °C (41 °F) may show a temporary drop in charging life;
the battery age display will however return to normal once
the battery has been recharged at a temperature of about
20 °C (68 °F) or higher.
352
U
Add a comment to new photographs as they are taken.
Comments can be viewed as metadata in ViewNX 2 (supplied) or
Capture NX 2 (available separately; 0393).
The comment is also
visible on the shooting data page in the photo information display
(0243).
•Done: Save changes and return to the setup menu.
•Input comment: Input a comment as described on page 180.
Comments can be up to 36 characters long.
•Attach comment: Select this option to
attach the comment to all subsequent
photographs.
Attach comment can be
turned on and off by highlighting it and
pressing 2.
Image Comment G button ➜Bsetup menu
353
U
Add copyright information to new photographs as they are taken.
Copyright information is included in the shooting data shown in
the photo information display (0243) and can be viewed as
metadata in ViewNX 2 (supplied) or in Capture NX 2 (available
separately; 0393).
•Done: Save changes and return to the setup menu.
•Artist: Enter a photographer name as described on page 180.
Photographer names can be up to 36 characters long.
•Copyright: Enter the name of the copyright holder as described
on page 180.
Copyright holder names can be up to 54 characters
long.
•Attach copyright information: Select this
option to attach copyright information to all
subsequent photographs.
Attach
copyright information can be turned on
and off by highlighting it and pressing 2.
Copyright Information G button ➜Bsetup menu
DCopyright Information
To prevent unauthorized use of the artist or copyright holder names,
make sure that Attach copyright information is not selected and that
the Artist and Copyright fields are blank before lending or transferring
the camera to another person.
Nikon does not accept liability for any
damages or disputes arising from the use of the Copyright
information option.
354
U
The software needed to create IPTC presets and save them to a
memory card can be downloaded using the supplied ViewNX 2
installer CD (Internet connection required) and installed on your
computer (for more information see the software’s on-line help).
The memory card can then be inserted in the camera’s primary
card slot and the options in the IPTC menu used to copy presets to
the camera and embed them in new photographs as described
below:
•Copy to camera: Copy IPTC presets from
the card in the primary card slot (095) to a
selected destination on the camera. The
camera can store up to ten presets.
To copy
a preset, highlight it and press J, then
highlight a destination and press J again
(to preview the preset highlighted in the source list, press 2,
then press J after viewing the preset to proceed to the
destination list).
•Edit: Select a preset from the list of IPTC presets stored on the
camera and choose Rename to rename the preset or Edit IPTC
information to select fields and edit their contents as described
on page 180.
•Delete: Select a preset for deletion from the
camera.
A confirmation dialog will be
displayed; highlight Yes and press J to
reset the selected preset.
•Auto embed during shooting: Highlight
the camera IPTC preset that will be
embedded in all subsequent photographs
and press J (to disable embedding, select
Off).
IPTC G button ➜Bsetup menu
355
U
DIPTC Information
IPTC is a standard established by the International Press
Telecommunications Council (IPTC) with the intent of clarifying and
simplifying the information required when photographs are shared
with a variety of publications. The camera supports standard roman
alphanumeric characters only; other characters will not display correctly
except on a computer.
Preset names (0354) may be up to
18 characters long (if a longer name is created using a computer, all
characters after the eighteenth will be deleted); the number of
characters that may appear in each field is given below; any characters
over the limit will not be displayed.
Field Maximum length Field Maximum length
Caption 2000 Supplemental
Categories
(Supp. Cat.)
256
Event ID 64
Headline 256
Object name 256 Byline 256
City 256 Byline title 256
State 256 Writer/editor 256
Country 256 Credit 256
Category 3 Source 256
356
U
Select Save settings to save the following settings to the memory
card, or to the memory card in the primary card slot if two memory
cards are inserted (095; if the card is full, an error will be
displayed). Use this option to share settings among D4 cameras.
Save/Load Settings G button ➜Bsetup menu
Menu Option
Playback
Playback display options
Image review
After delete
Rotate tall
Shooting
(all banks)
Shooting menu bank
Extended menu banks
File naming
Primary slot selection
Secondary slot function
Image quality
Image size
Image area
JPEG compression
NEF (RAW) recording
White balance (with fine-tuning and presets d-1–d-4)
Set Picture Control; note that Standard is used for
Picture Controls other than the six preset Picture
Controls supplied with the camera (Standard, Neutral,
Vivid, Monochrome, Portrait, and Landscape)
Color space
Active D-Lighting
Vignette control
Auto distortion control
Long exposure NR
357
U
Settings saved using the D4 can be restored by selecting Load
settings.
Note that Save/load settings is only available when a
memory card is inserted in the camera, and that the Load settings
option is only available if the card contains saved settings.
Shooting
(all banks)
High ISO NR
ISO sensitivity settings
Live view photography
Movie settings
Custom settings
(all banks) All Custom Settings
Setup
Clean image sensor
HDMI
Flicker reduction
Time zone and date (excepting date and time)
Language
Auto image rotation
Image comment
Copyright information
IPTC
Voice memo options
GPS
Non-CPU lens data
My Menu/
Recent Settings
All My Menu items
All recent settings
Choose tab
ASaved Settings
Settings are saved in a file named NCSETUP9.
The camera will not be
able to load settings if the file name is changed.
Menu Option
358
U
Display roll and pitch information based on information from the
camera tilt sensor.
If the camera is tilted neither left nor right, the
roll reference line will turn green, while if the camera is tilted
neither forward nor back, the pitch reference line will turn green
and a dot will appear in the center of the display.
Each division is
equivalent to 5°.
Virtual Horizon G button ➜Bsetup menu
Camera level Camera tilted left or
right
Camera tilted forward
or back
DTilting the Camera
The virtual horizon display is not accurate when the camera is tilted at a
sharp angle forward or back. If the camera is unable to measure tilt, the
amount of tilt will not be displayed.
ASee Also
For information on viewing a virtual horizon display in the viewfinder,
see Custom Setting f3 (Assign Fn button > Press; 0328, 330).
For
information on displaying a virtual horizon in live view, see pages 58
and 70.
359
U
Fine-tune focus for up to 20 lens types. AF tuning is not
recommended in most situations and may interfere with normal
focus; use only when required.
AF Fine-Tune G button ➜Bsetup menu
Option Description
AF fine
tune
(On/Off)
•On: Turn AF tuning on.
•Off: Turn AF tuning off.
Saved
value
Tune AF for the current lens (CPU
lenses only). Press
1
or
3
to choose
a value between +20 and –20.
Values for up to 20 lens types can be
stored. Only one value can be
stored for each type of lens.
Default
Choose the AF tuning value used
when no previously saved value
exists for the current lens (CPU
lenses only).
List
saved
values
List previously saved AF tuning values. To delete a lens from the
list, highlight the desired lens and press
O
(
Q
). To change a lens
identifier (for example, to choose an identifier that is the same as
the last two digits of the lens serial number to distinguish it from
other lenses of the same type in light of the fact that
Saved value
can be used with only one
lens of each type), highlight the desired
lens and press
2
.
The menu shown at
right will be displayed; press
1
or
3
to
choose an identifier and press
J
to save
changes and exit.
Move focal
point away
from camera.
Current
value
Move focal
point toward
camera.
Previous
value
360
U
View the current camera firmware version.
DAF Tuning
The camera may be unable to focus at minimum range or at infinity
when AF tuning is applied.
DLive View
Tuning is not applied to autofocus during live view (052).
ASaved Value
Only one value can be stored for each type of lens.
If a teleconverter is
used, separate values can be stored for each combination of lens and
teleconverter.
Firmware Version G button ➜Bsetup menu
361
U
NThe Retouch Menu:
Creating Retouched Copies
To display the retouch menu, press G and select the N (retouch
menu) tab.
The options in the retouch menu are used to create trimmed, or
retouched copies of existing pictures.
The retouch menu is only
displayed when a memory card containing photographs is
inserted in the camera (note that if the memory card is being used
to store both RAW/NEF and JPEG copies of the same photographs
as described on page 90, retouch other than Image overlay and
NEF (RAW) processing apply only to the JPEG copies).
1 Can only be selected by pressing G and selecting N tab.
2 Can only be displayed by holding J and pressing 2 in full-frame playback
when a retouched image or original is displayed.
G button
Option 0
iD-Lighting 364
jRed-eye correction 365
kTrim 366
lMonochrome 367
mFilter effects 367
nColor balance 368
oImage overlay1369
7NEF (RAW) processing 372
8Resize 374
ZStraighten 376
aDistortion control 377
ePerspective control 378
9Edit movie 79
pSide-by-side comparison2378
Option 0
362
U
Creating Retouched Copies
To create a retouched copy:
1Select an item in the
retouch menu.
Press 1 or 3 to highlight an
item, 2 to select.
2Select a picture.
Highlight a picture and press J
(to view the highlighted picture
full screen, press and hold the X
button).
To view images in other locations, press
W and select the desired card and folder
as described on page 236.
3Select retouch options.
For more information, see the section for the selected item.
To
exit without creating a retouched copy, press G.
ARetouch
The camera may not be able to display or
retouch images created with other devices.
AMonitor off Delay
The monitor will turn off automatically if no operations are
performed for a brief period. Any unsaved changes will be lost. To
increase the time the monitor remains on, choose a longer menu
display time for Custom Setting c4 (Monitor off delay, 0317).
363
U
4Create a retouched
copy.
Press J to create a
retouched copy.
Retouched copies are
indicated by a & icon.
ACreating Retouched Copies During Playback
Retouched copies can also be created during playback.
Display picture full
frame and hold J and
press 2.
Highlight option and
press J.
Create retouched
copy.
DRetouching Copies
Most options can be applied to copies created using other retouch
options, although with the exceptions of Image overlay and
Edit movie > Choose start/end point each option can be applied only
once (note that multiple edits may result in loss of detail).
Options that
can not be applied to the current image are grayed out and unavailable.
AImage Quality
Except in the case of copies created with Trim, Image overlay, NEF
(RAW) processing, and Resize, copies created from JPEG images are
the same size and quality as the original, copies created from NEF (RAW)
photos are saved as large fine-quality JPEG images, and copies created
from TIFF (RGB) photos are saved as fine-quality JPEG images of the
same size as the original.
Size-priority compression is used when copies
are saved in JPEG format.
J button
364
U
D-Lighting brightens shadows, making it ideal for dark or backlit
photographs.
Press 1 or 3 to choose the amount of
correction performed.
The effect can be
previewed in the edit display.
Press J to copy
the photograph.
D-Lighting G button ➜Nretouch menu
Before After
365
U
This option is used to correct “red-eye” caused by the flash and is
available only with photographs taken using a flash.
The
photograph selected for red-eye correction can be previewed in
the edit display.
Confirm the effects of red-eye correction and
create a copy as described in the following table.
Note that
red-eye correction may not always produce the expected results
and may in very rare circumstances be applied to portions of the
image that are not affected by red-eye; check the preview
thoroughly before proceeding.
Red-Eye Correction G button ➜Nretouch menu
To Use Description
Zoom in XPress X to zoom in, W to
zoom out.
While photo is
zoomed in, use multi
selector to view areas of
image not visible in
monitor.
Keep multi
selector pressed to scroll
rapidly to other areas of frame.
Navigation
window is displayed when zoom buttons or multi
selector are pressed; area currently visible in
monitor is indicated by yellow border.
Press J to
cancel zoom.
Zoom out W
View other
areas of image
Cancel zoom J
Create copy J
If the camera detects red-eye in the selected
photograph, a copy will be created that has been
processed to reduce its effects.
No copy will be
created if the camera is unable to detect red-eye.
366
U
Create a cropped copy of the selected
photograph.
The selected photograph is
displayed with the selected crop shown in
yellow; create a cropped copy as described in
the following table.
Trim G button ➜Nretouch menu
To Use Description
Reduce size of
crop WPress W to reduce the size of the crop.
Increase size of
crop XPress X to increase the size of the crop.
Change crop
aspect ratio
Rotate the main command dial to switch
between aspect ratios of 3 : 2, 4 : 3, 5 : 4, 1 : 1,
and 16 : 9.
Position crop
Use multi selector to position the crop.
Press
and hold to move the crop rapidly to the
desired position.
Preview crop Press center of multi selector to preview
cropped image.
Create copy JSave the current crop as a separate file.
ATrim: Image Quality and Size
Copies created from NEF (RAW), NEF
(RAW) + JPEG, or TIFF (RGB) photos have an
image quality (090) of JPEG fine; cropped
copies created from JPEG photos have the same
image quality as the original.
The size of the
copy varies with crop size and aspect ratio and
appears at upper left in the crop display.
AViewing Cropped Copies
Playback zoom may not be available when cropped copies are
displayed.
367
U
Copy photographs in Black-and-white,
Sepia, or Cyanotype (blue and white
monochrome).
Selecting Sepia or Cyanotype
displays a preview of the selected
image; press 1 to increase color
saturation, 3 to decrease.
Press J
to create a monochrome copy.
Choose from the following color filter effects.
After adjusting filter
effects as described below, press J to copy the photograph.
Monochrome G button ➜Nretouch menu
Filter Effects G button ➜Nretouch menu
Option Description
Skylight
Creates the effect of a skylight
filter, making the picture less
blue.
The effect can be previewed
in the monitor as shown at right.
Warm filter
Creates a copy with warm tone filter effects, giving the
copy a “warm” red cast.
The effect can be previewed in
the monitor.
Increase
saturation
Decrease
saturation
368
U
Use the multi selector to create a copy with
modified color balance as shown below.
The
effect is displayed in the monitor together
with red, green, and blue histograms (0241)
giving the distribution of tones in the copy.
Press J to copy the photograph.
Color Balance G button ➜Nretouch menu
Increase amount of green
Increase amount of blue Increase amount of amber
Increase amount of magenta
AZoom
To zoom in on the image displayed in the
monitor, press X.
The histogram will be updated
to show data only for the portion of the image
displayed in the monitor.
While the image is
zoomed in, press L (Z/Q) to toggle back and
forth between color balance and zoom.
When
zoom is selected, you can zoom in and out with
the X and W buttons and scroll the image with
the multi selector.
369
U
Image overlay combines two existing NEF (RAW) photographs to
create a single picture that is saved separately from the originals;
the results, which make use of RAW data from the camera image
sensor, are noticeably better than photographs combined in an
imaging application.
The new picture is saved at current image
quality and size settings; before creating an overlay, set image
quality and size (090, 93; all options are available).
To create a
NEF (RAW) copy, choose an image quality of NEF (RAW).
1Select Image overlay.
Highlight Image overlay and
press 2.
The dialog shown at
right will be displayed, with
Image 1 highlighted; press J
to display a picture selection
dialog listing only NEF (RAW) images created with this camera.
Image Overlay G button ➜Nretouch menu
+
370
U
2Select the first image.
Use the multi selector to
highlight the first photograph
in the overlay.
To view the
highlighted photograph full
frame, press and hold the X
button.
To view images in other locations, press W and select
the desired card and folder as described on page 236.
Press J
to select the highlighted photograph and return to the
preview display.
3Select the second image.
The selected image will appear as Image 1.
Highlight Image 2
and press J, then select the second photo as described in
Step 2.
4Adjust gain.
Highlight Image 1 or Image 2
and optimize exposure for the
overlay by pressing 1 or 3 to
select the gain from values
between 0.1 and 2.0.
Repeat
for the second image.
The default value is 1.0; select 0.5 to
halve gain or 2.0 to double it.
The effects of gain are visible in
the Preview column.
371
U
5Preview the overlay.
Press 4 or 2 to place the
cursor in the Preview column
and press 1 or 3 to highlight
Overlay.
Press J to preview
the overlay as shown at right
(to save the overlay without displaying a preview, select Save).
To return to Step 4 and select new photos or adjust gain, press
W.
6Save the overlay.
Press J while the preview
is displayed to save the
overlay.
After an overlay is
created, the resulting
image will be displayed
full-frame in the monitor.
DImage Overlay
Only NEF (RAW) photographs with the same image area and bit-depth
can be combined.
The overlay has the same photo info (including date of recording,
metering, shutter speed, aperture, exposure mode, exposure
compensation, focal length, and image orientation) and values for
white balance and Picture Control as the photograph selected for
Image 1.
The current image comment is appended to the overlay when
it is saved; copyright information, however, are not copied.
Overlays
saved in NEF (RAW) format use the compression selected for Type in the
NEF (RAW) recording menu and have the same bit depth as the
original images; JPEG overlays are saved using size-priority
compression.
J button
372
U
Create JPEG copies of NEF (RAW) photographs.
1Select NEF (RAW)
processing.
Highlight NEF (RAW)
processing and press 2 to
display a picture selection
dialog listing only NEF (RAW) images created with this camera.
2Select a photograph.
Highlight a photograph (to
view the highlighted
photograph full frame, press
and hold the X button; to view
images in other locations as described on page 236, press W).
Press J to select the highlighted photograph and proceed to
the next step.
NEF (RAW) Processing G button ➜Nretouch menu
373
U
3Adjust NEF (RAW) processing settings.
Adjust the settings listed below.
Note that white balance and
vignette control are not available with multiple exposures or
pictures created with image overlay and that exposure
compensation can only be set to values between –2 and
+2 EV.
If Auto is selected for white balance, it will be set to
whichever of Normal and Keep warm lighting colors was in
effect when the picture was taken. The Picture Control grid is
not displayed when Picture Controls are adjusted.
4Copy the photograph.
Highlight EXE and press J
to create a JPEG copy of
the selected photograph.
To exit without copying
the photograph, press the
G button.
Image quality (090)
Image size (093)
White balance (0153)
Exposure comp. (0137)
Picture Control (0173)
High ISO NR (0302)
Color space (0299)
Vignette control (0300)
D-Lighting (0364)
J button
374
U
Create small copies of selected photographs.
1Select Resize.
To resize selected images, press
G to display the menus and
select Resize in the retouch
menu.
2Choose a destination.
If two memory cards are
inserted, you can choose a
destination for the resized
copies by highlighting Choose
destination and pressing 2 (if
only one memory card is
inserted, proceed to Step 3).
The menu shown at right will be
displayed; highlight a card slot
and press J.
Resize G button ➜Nretouch menu
375
U
3Choose a size.
Highlight Choose size and
press 2.
The options shown at right will
be displayed; highlight an
option and press J.
4Choose pictures.
Highlight Select image and
press 2.
Highlight pictures and press the
center of the multi selector to
select or deselect (to view the
highlighted picture full screen,
press and hold the X button; to
view pictures in other locations
as described on page 236, press W).
Selected pictures are
marked by a 8 icon.
Press J when the selection is complete.
Note that photographs taken at an image-area setting of 5 : 4
(086) can not be resized.
376
U
5Save the resized copies.
A confirmation dialog will
be displayed.
Highlight
Yes and press J to save
the resized copies.
Create a straightened copy of the selected
image.
Press 2 to rotate the image clockwise
by up to five degrees in increments of
approximately 0.25 degrees, 4 to rotate it
counterclockwise (the effect can be
previewed in the edit display; note that edges
of the image will be trimmed to create a square copy).
Press J to
copy the photograph, or press K to exit to playback without
creating a copy.
AViewing Resized Copies
Playback zoom may not be available when resized copies are displayed.
AImage Quality
Copies created from NEF (RAW), NEF (RAW) + JPEG, or TIFF (RGB) photos
have an image quality (090) of JPEG fine; copies created from JPEG
photos have the same image quality as the original.
Straighten G button ➜Nretouch menu
J button
377
U
Create copies with reduced peripheral
distortion.
Select Auto to let the camera
correct distortion automatically and then
make fine adjustments using the multi
selector, or select Manual to reduce
distortion manually (note that Auto is not
available with photos taken using auto distortion control; see
page 301).
Press 2 to reduce barrel distortion, 4 to reduce
pincushion distortion (the effect can be previewed in the edit
display; note that greater amounts of distortion control result in
more of the edges being cropped out).
Press J to copy the
photograph, or press K to exit to playback without creating a
copy.
Note that distortion control may heavily crop or distort the
edges of copies created from photographs taken with DX lenses at
image areas other than DX (24×16) 1.5×.
Distortion Control G button ➜Nretouch menu
AAuto
Auto is for use only with pictures taken with type G and D lenses (PC,
fisheye, and certain other lenses excluded).
Results are not guaranteed
with other lenses.
378
U
Create copies that reduce the effects of
perspective taken from the base of a tall
object.
Use the multi selector to adjust
perspective (note that greater amounts of
perspective control result in more of the
edges being cropped out).
The results can be
previewed in the edit display.
Press J to copy the photograph, or
press K to exit to playback without creating a copy.
Compare retouched copies to the original photographs.
This
option is only available if the retouch menu is displayed by
pressing the J and 2 buttons when a copy or original is displayed
full frame.
1Select a picture.
Select a retouched copy
(shown by a & icon) or a
photograph that has been
retouched in full-frame
playback and press the J
and 2 buttons.
Perspective Control G button ➜Nretouch menu
Before After
Side-by-Side Comparison
J button
379
U
2Select Side-by-side
comparison.
Highlight Side-by-side
comparison and press J.
3Compare the copy with the
original.
The source image is displayed
on the left, the retouched copy
on the right, with the options
used to create the copy listed
at the top of the display.
Press
4 or 2 to switch between the
source image and the
retouched copy.
To view the highlighted picture full frame,
press and hold the X button.
If the copy was created from two
images using Image overlay, press 1 or 3 to view the other
source image.
If multiple copies exist for the current source
image, press 1 or 3 to view the other copies.
To exit to
playback, press the K button, or press J to exit to playback
with the highlighted image selected.
DSide-by-Side Comparison
The source image will not be displayed if the copy was created from a
photograph that was protected (0249) or has since been deleted or
hidden (0284).
Options used to
create copy
Source
image
Retouched
copy
380
U
OMy Menu/mRecent Settings
To display My Menu, press G and select the O (My Menu) tab.
The My Menu option can be used to create and edit a customized
list of options from the playback, shooting, Custom Settings,
setup, and retouch menus for quick access (up to 20 items).
If
desired, recent settings can be displayed in place of My Menu
(0384).
Options can be added, deleted, and reordered as described on the
following pages.
G button
381
U
❚❚ Adding Options to My Menu
1Select Add items.
In My Menu (O), highlight Add
items and press 2.
2Select a menu.
Highlight the name of the
menu containing the option
you wish to add and press 2.
3Select an item.
Highlight the desired
menu item and press J.
4Position the new item.
Press 1 or 3 to move the new
item up or down in My Menu.
Press J to add the new item.
5Add more items.
The items currently displayed in My
Menu are indicated by a check mark.
Items indicated by a V icon can not be
selected.
Repeat steps 1–4 to select
additional items.
J button
382
U
❚❚ Deleting Options from My Menu
1Select Remove items.
In My Menu (O), highlight Remove items and press 2.
2Select items.
Highlight items and press 2 to
select or deselect.
Selected
items are indicated by a check
mark.
3Select Done.
Highlight Done and press
J.
A confirmation dialog
will be displayed.
4Delete the selected items.
Press J to delete the selected
items.
ADeleting Items in My Menu
To delete the item currently highlighted in My Menu, press the O (Q)
button.
A confirmation dialog will be displayed; press O (Q) again to
remove the selected item from My Menu.
J button
383
U
❚❚ Reordering Options in My Menu
1Select Rank items.
In My Menu (O), highlight Rank items and press 2.
2Select an item.
Highlight the item you
wish to move and press J.
3Position the item.
Press 1 or 3 to move the item
up or down in My Menu and
press J.
Repeat Steps 2–3 to
reposition additional items.
4Exit to My Menu.
Press the G button to
return to My Menu.
J button
G button
384
U
Recent Settings
To display the twenty most recently used settings, select mRecent
settings for OMy Menu > Choose tab.
1Select Choose tab.
In My Menu (O), highlight
Choose tab and press 2.
2Select mRecent
settings.
Highlight mRecent
settings and press J.
The
name of the menu will
change from “MY MENU”
to “RECENT SETTINGS.”
Menu items will be added to the top of the recent settings menu
as they are used.
To view My Menu again, select OMy Menu for
mRecent settings > Choose tab.
ARemoving Items from the Recent Settings Menu
To remove an item from the recent settings menu, highlight it and press
the O (Q) button.
A confirmation dialog will be displayed; press O (Q)
again to delete the selected item.
J button
n
385
n
Technical Notes
Read this chapter for information on compatible accessories,
cleaning and storing the camera, and what to do if an error
message is displayed or you encounter problems using the camera.
1 IX-NIKKOR lenses can not be used.
2 Vibration Reduction (VR) supported with VR lenses.
3 Spot metering meters selected focus point (0123).
Compatible Lenses
Camera setting Focus mode Exposure
mode Metering system
Lens/accessory
AF
M (with
electronic
rangefinder)
Me
f
g
h
LM
N
3D Color
CPU lenses1
Type G or D AF NIKKOR2
AF-S, AF-I NIKKOR ✔ ✔ ✔✔✔✔ —✔3
PC-E NIKKOR series — ✔5✔✔
5✔5✔5—
✔
3,5
PC Micro 85mm f/2.8D4—✔5✔—✔6✔—
✔
3,5
AF-S / AF-I Teleconverter7✔ ✔ ✔✔✔✔ —✔3
Other AF NIKKOR
(except lenses for F3AF) ✔9✔9✔✔✔—✔✔
3
AI-P NIKKOR — ✔10 ✔✔✔—✔✔
3
Non-CPU lenses 11
AI-, AI-modified, NIKKOR
or Nikon Series E lenses12 —✔10 ✔—✔13 —✔14 ✔15
Medical-NIKKOR 120mm
f/4 —✔✔—✔16 ———
Reflex-NIKKOR — — ✔—✔13 ——✔15
PC-NIKKOR — ✔5✔—✔17 ——✔
AI-type Teleconverter 18 —✔8✔—✔13 —✔14 ✔15
PB-6 Bellows Focusing
Attachment 19 —✔8✔—✔20 ——✔
Auto extension rings
(PK-series 11A, 12, or 13;
PN-11)
—✔8✔—✔13 ——✔
386
n
4 The camera’s exposure metering and flash control systems do not work
properly when shifting and/or tilting the lens, or when an aperture other than
the maximum aperture is used.
5 Can not be used with shifting or tilting.
6 Manual exposure mode only.
7 Can be used with AF-S and AF-I lenses only (0387).
For information on the
focus points available for autofocus and electronic rangefinding, see page 387.
8 With maximum effective aperture of f/5.6 or faster.
9 When focusing at minimum focus distance with AF 80–200mm f/2.8, AF
35–70mm f/2.8, AF 28–85mm f/3.5–4.5 <New>, or AF 28–85mm f/3.5–4.5 lens
at maximum zoom, in-focus indicator may be displayed when image on matte
screen in viewfinder is not in focus.
Adjust focus manually until image in
viewfinder is in focus.
10 With maximum aperture of f/5.6 or faster.
11 Some lenses can not be used (see page 388).
12 Range of rotation for AI 80–200mm f/2.8 ED tripod mount is limited by camera body.
Filters can not be exchanged while AI 200–400mm f/4 ED is mounted on camera.
13 If maximum aperture is specified using Non-CPU lens data (0228), aperture
value will be displayed in viewfinder and top control panel.
14 Can be used only if lens focal length and maximum aperture are specified using
Non-CPU lens data (0228).
Use spot or center-weighted metering if desired
results are not achieved.
15 For improved precision, specify lens focal length and maximum aperture using
Non-CPU lens data (0228).
16 Can be used in manual exposure modes at shutter speeds slower than flash
sync speed by one step or more.
17 Exposure determined by presetting lens aperture.
In aperture-priority auto
exposure mode, preset aperture using lens aperture ring before performing AE
lock and shifting lens.
In manual exposure mode, preset aperture using lens
aperture ring and determine exposure before shifting lens.
18 Exposure compensation required when used with AI 28–85mm f/3.5–4.5, AI
35–105mm f/3.5–4.5, AI 35–135mm f/3.5–4.5, or AF-S 80–200mm f/2.8D.
See
teleconverter manual for details.
19 Requires PK-12 or PK-13 auto extension ring.
PB-6D may be required
depending on camera orientation.
20 Use preset aperture.
In aperture-priority auto exposure mode, set aperture
using focusing attachment before determining exposure and taking
photograph.
• PF-4 Reprocopy Outfit requires PA-4 Camera Holder.
• Noise in the form of lines may appear during autofocus at high ISO sensitivities.
Use manual focus or focus lock. Lines may also appear at high ISO sensitivities
when aperture is adjusted during movie recording or live view photography.
387
n
ARecognizing CPU and Type G and D Lenses
CPU lenses (particularly types G and D) are recommended, but note that
IX-NIKKOR lenses can not be used.
CPU lenses can be identified by the
presence of CPU contacts, type G and D lenses by a letter on the lens
barrel.
Type G lenses are not equipped with a lens aperture ring.
CPU contacts Aperture ring
CPU lens Type G lens Type D lens
AThe AF-S/AF-I Teleconverter
The AF-S/AF-I teleconverter can be used with the following AF-S and
AF-I lenses:
• AF-S NIKKOR 70–200mm f/2.8G ED VR II
• AF-S VR 70–200mm f/2.8G ED
• AF-S 80–200mm f/2.8D ED
• AF-S VR Micro-Nikkor 105mm
f/2.8G IF-ED 1
• AF-S NIKKOR 200mm f/2G ED VR II
• AF-S VR 200mm f/2G ED
• AF-S NIKKOR 200–400mm f/4G ED VR II
2
• AF-S VR 200–400mm f/4G ED 2
• AF-S NIKKOR 300mm f/2.8G ED VR II
• AF-S VR 300mm f/2.8G ED
• AF-S 300mm f/2.8D ED II
• AF-S 300mm f/2.8D ED
• AF-I 300mm f/2.8D ED
• AF-S 300mm f/4D ED 2
• AF-S NIKKOR 400mm f/2.8G ED VR
• AF-S 400mm f/2.8D ED II
• AF-S 400mm f/2.8D ED
• AF-I 400mm f/2.8D ED
• AF-S NIKKOR 500mm f/4G ED VR 2
• AF-S 500mm f/4D ED II 2
• AF-S 500mm f/4D ED 2
• AF-I 500mm f/4D ED 2
• AF-S NIKKOR 600mm f/4G ED VR 2
• AF-S 600mm f/4D ED II 2
• AF-S 600mm f/4D ED 2
• AF-I 600mm f/4D ED 2
1 Autofocus not supported.
2 Autofocus and electronic
rangefinding support focus
points shown at right when
used with TC-17E II, TC-20E II, or TC-20E III AF-S teleconverters.
When used
with TC-20E II/TC-20E III, focus data for focus points other than the center focus
point are obtained from line sensors.
Single point AF is used when 3D-
tracking or auto-area AF is selected for AF-area mode (0100); at combined
apertures slower than f/5.6, the camera may not be able to focus on dark or
low-contrast subjects.
TC-17E II TC-20E II/
TC-20E III
388
n
ALens f-number
The f-number given in lens names is the maximum aperture of the lens.
ACompatible Non-CPU Lenses
When using non-CPU lenses and accessories, select exposure mode g or
h and set aperture using the lens aperture ring.
In other modes, the
shutter-release is disabled.
Non-CPU lens data (0228) can be used to
enable many of the features available with CPU lenses, including color
matrix metering; if no data are provided, center-weighted metering will
be used in place of color matrix metering, while if the maximum
aperture is not provided, the camera aperture display will show the
number of stops from maximum aperture and the actual aperture value
must be read off the lens aperture ring.
DIncompatible Accessories and Non-CPU Lenses
The following can NOT be used with the D4:
• TC-16AS AF teleconverter
•Non-AI lenses
• Lenses that require the AU-1 focusing
unit (400mm f/4.5, 600mm f/5.6,
800mm f/8, 1200mm f/11)
• Fisheye (6mm f/5.6, 7.5mm f/5.6,
8mm f/8, OP 10mm f/5.6)
•2.1cm f/4
•Extension Ring K2
• 180–600mm f/8 ED (serial numbers
174041–174180)
• 360–1200mm f/11 ED (serial numbers
174031–174127)
• 200–600mm f/9.5 (serial numbers
280001–300490)
• AF lenses for the F3AF (AF 80mm
f/2.8, AF 200mm f/3.5 ED,
AF Teleconverter TC-16)
• PC 28mm f/4 (serial number 180900
or earlier)
• PC 35mm f/2.8 (serial numbers
851001–906200)
• PC 35mm f/3.5 (old type)
• Reflex 1000mm f/6.3 (old type)
• Reflex 1000mm f/11 (serial numbers
142361–143000)
• Reflex 2000mm f/11 (serial numbers
200111–200310)
389
n
ACalculating Angle of View
The D4 can be used with Nikon lenses for 35 mm (135) format cameras.
If Auto DX crop is on (085) and a 35 mm format lens is attached, the
angle of view will be the same as a frame of 35 mm film (36.0 × 23.9 mm);
if a DX lens is attached, the angle of view will automatically be adjusted
to 23.4 × 15.5 mm (DX format).
To choose an angle of view different from that of the current lens, turn
Auto DX crop off and select from FX (36×24), 1.2× (30×20),
DX (24 × 16), and 5 : 4 (30×24).
If a 35 mm format lens is attached, the
angle of view could be reduced by 1.5 × by selecting DX (24×16) or by
1.2 × by selecting 1.2× (30×20), to expose a smaller area, or the aspect
ratio could be changed by selecting 5 : 4 (30×24).
Lens
FX (36×24) picture size (36.0 × 23.9 mm,
equivalent to 35 mm format camera)
Picture diagonal
DX (24×16) picture size
(23.4 × 15.5 mm, equivalent to DX
format camera)
5 : 4 (30×24) picture size
(29.9 × 23.9 mm)
Angle of view (FX (36×24);
35 mm format)
Angle of view (DX (24× 16); DX format)
Angle of view (5:4 (30×24))
1.2× (30×20) picture size
(29.9 × 19.9 mm)
Angle of view (1.2× (30×20))
390
n
ACalculating Angle of View (Continued)
The DX (24×16) angle of view is about 1.5 times smaller than the 35 mm
format angle of view, while the 1.2× (30×20) angle of view is about 1.2
times smaller and the 5 : 4 (30×24) angle of view is about 1.1 times
smaller.
To calculate the focal length of lenses in 35 mm format when
DX (24×16) is selected, multiply the focal length of the lens by about
1.5, by about 1.2 when is 1.2× (30×20) selected, or by about 1.1 when
5:4 (30×24) is selected (for example, the effective focal length of a
50mm lens in 35 mm format would be 75 mm when DX (24×16) is
selected, 60 mm when 1.2× (30×20) is selected, or 55 mm when
5:4(30×24) is selected).
391
n
Other Accessories
At the time of writing, the following accessories were available for
the D4.
Power sources
•Rechargeable Li-ion Battery EN-EL18 (023, 25): Additional
EN-EL18 batteries are available from local retailers and
Nikon service representatives.
These batteries can be
recharged and calibrated using an MH-26 battery charger.
•Battery Charger MH-26 (023, 440): The MH-26 can be used to
recharge and calibrate EN-EL18 batteries.
•Power Connector EP-6, AC Adapter EH-6b: These accessories can
be used to power the camera for extended periods (EH-6
AC adapters can also be used).
The EP-6 is required to
connect the EH-6b to the camera; see page 396 for details.
Wireless LAN
adapters
(0269)
•Wireless Transmitter WT-4: Connects the camera to wireless
and Ethernet networks.
The photographs on the camera
memory card can be viewed by computers on the same
network or copied to a computer for long-term storage.
The camera can also be controlled from any computer on
the network using Camera Control Pro 2 (available
separately).
Note that the WT-4 requires an independent
power source in the form of an optional EH-6b AC adapter
or EN-EL3e battery.
See the WT-4 manual for details.
•Wireless Transmitter WT-5:Connect the WT-5 to the camera’s
peripheral connector to upload pictures over a wireless
network, to control the camera from a computer running
Camera Control Pro 2 (available separately), or to take and
browse pictures remotely from a computer or iPhone.
See
the WT-5 manual for details.
Note: A wireless network and some basic network knowledge is
required when using a wireless transmitter.
Be sure to upgrade
the software supplied with the wireless transmitter to the
latest version.
392
n
Viewfinder
eyepiece
accessories
•Rubber Eyecup DK-19: The DK-19 makes the image in the
viewfinder easier to see, preventing eye fatigue.
•Diopter-Adjustment Viewfinder Lens DK-17C: To accommodate
individual differences in vision, viewfinder lenses are
available with diopters of –3, –2, 0, +1, and +2 m–1.
Use
diopter adjustment lenses only if the desired focus can
not be achieved with the built-in diopter adjustment
control (–3 to +1 m–1).
Test diopter adjustment lenses
before purchase to ensure that the desired focus can be
achieved. The DK-17C is equipped with a safety lock.
•Magnifying Eyepiece DK-17M: The DK-17M magnifies the view
through the viewfinder by approximately 1.2 × for greater
precision when framing. The DK-17M is equipped with a
safety lock.
•Eyepiece Magnifier DG-2: The DG-2 magnifies the scene at the
center of the viewfinder for more accurate focus.
DK-18
eyepiece adapter (available separately) required.
•Eyepiece Adapter DK-18: The DK-18 is used when attaching
the DG-2 magnifier or DR-3 right-angle viewing
attachment to the D4.
• Antifog Finder Eyepiece DK-14/Antifog Finder Eyepiece DK-17A:
These viewfinder eyepieces prevent fogging in humid or
cold conditions. The DK-17A is equipped with a safety
lock.
•Right-Angle Viewing Attachment DR-5/Right-Angle Viewing
Attachment DR-4: The DR-5 and DR-4 attach to the
viewfinder eyepiece at a right angle, allowing the image in
the viewfinder to be viewed from above when the camera
is in the horizontal shooting position. The DR-5 supports
diopter adjustment and can also magnify the view
through the viewfinder by 2 × for greater precision when
framing (note that the edges of the frame will not be
visible when the view is magnified).
393
n
Filters
• Filters intended for special-effects photography may
interfere with autofocus or the electronic rangefinder.
• The D4 can not be used with linear polarizing filters.
Use
the C-PL or C-PLII circular polarizing filter instead.
• Use NC filters to protect the lens.
• To prevent ghosting, use of a filter is not recommended
when the subject is framed against a bright light, or when
a bright light source is in the frame.
• Center-weighted metering is recommended with filters
with exposure factors (filter factors) over 1× (Y44, Y48,
Y52, O56, R60, X0, X1, C-PL, ND2S, ND4, ND4S, ND8, ND8S,
ND400, A2, A12, B2, B8, B12).
See the filter manual for
details.
PC card
adapters
PC Card Adapter EC-AD1: The EC-AD1 PC card adapter allows
Type I CompactFlash memory cards to be inserted in
PCMCIA card slots.
Software
•Capture NX 2: A complete photo editing package with such
advanced editing features as selection control points and
an auto retouch brush.
•Camera Control Pro 2: Control the camera remotely from a
computer and save photographs directly to the computer
hard disk.
Note: Use the latest versions of Nikon software; see the websites
listed on page xxi for the latest information on supported
operating systems. At default settings, Nikon Message Center 2
will periodically check for updates to Nikon software and
firmware while you are logged in to an account on the
computer and the computer is connected to the Internet. A
message is automatically displayed when an update is found.
394
n
Body caps
Body Cap BF-1B/Body Cap BF-1A: The body cap keeps the mirror,
viewfinder screen, and low-pass filter free of dust when a
lens is not in place.
Remote
terminal
accessories
The D4 is equipped with a ten-pin remote terminal (03) for
remote control and automatic photography.
The terminal is
provided with a cap, which protects the contacts when the
terminal is not in use.
The following accessories can be used
(all lengths are approximate):
•Remote Cord MC-22: Remote shutter release with blue, yellow,
and black terminals for connection to a remote shutter-
triggering device, allowing control via sound or electronic
signals (length 1 m/3 ft 3 in.).
•Remote Cord MC-30: Remote shutter release; can be used to
reduce camera shake (length 80 cm/2 ft 7 in.).
•Remote Cord MC-36: Remote shutter release; can be used for
interval timer photography or to reduce camera shake or
keep the shutter open during a time exposure (length
85 cm/2 ft 9 in.).
•Extension Cord MC-21: Can be connected to ML-3 or MC-series
20, 22, 23, 25, 30, or 36. Only one MC-21 can be used at a
time (length 3 m/9 ft 10 in.).
•Connecting Cord MC-23: Connects two cameras for
simultaneous operation (length 40 cm/1 ft 4 in.).
•Adapter Cord MC-25: Ten-pin to two-pin adapter cord for
connection to devices with two-pin terminals, including
the MW-2 radio control set, MT-2 intervalometer, and
ML-2 modulite control set (length 20 cm/8 in.).
•GPS Unit GP-1 (0231): Record latitude, longitude, altitude,
and UTC time with pictures.
395
n
Remote
terminal
accessories
•GPS Adapter Cord MC-35 (0231): This 35 cm (1 ft 2 in.) cable
connects the camera to older GARMIN eTrex- and geko-
series GPS units that conform to version 2.01 or 3.01 of the
National Marine Electronics Association NMEA0183 data
format. Only models that support PC interface cable
connections are supported; the MC-35 can not be used to
connect GPS units via USB. The units connect to the
MC-35 using a cable with a D-sub 9-pin connector
provided by the manufacturer of the GPS device; see the
MC-35 instruction manual for details. Before turning the
camera on, set the GPS device to NMEA mode
(4800 baud); for more information, see the
documentation provided with the GPS device.
•Modulite Remote Control Set ML-3: Allows infrared remote
control at ranges of up to 8 m (26 ft 3 in.).
Microphones
Stereo Microphone ME-1: Connect the ME-1 to the camera
microphone jack to record stereo sound while reducing the
noise caused by lens vibration being recorded with movies
during autofocus (069).
AThe UF-2 Connector Cover for Stereo Mini-Plug Cables
The camera comes with a UF-2 connector cover for the stereo mini-plug
cable on the optional ME-1 stereo microphone (01) that prevents the
cable connecting the ME-1 to the camera being accidentally
disconnected. The cover attaches as shown.
396
n
Attaching a Power Connector and AC
Adapter
Turn the camera off before attaching an optional power connector
and AC adapter.
1Remove the battery-chamber cover.
Lift the battery-chamber cover latch, turn
it to the open (A) position (q), and
remove the BL-6 battery-chamber cover
(w).
2Connect the AC adapter.
Pass the DC cable over the power
connector cable guide (q) and slide it
down until it is at the bottom of the slot,
and then insert the DC plug into the DC IN
connector (w).
3Insert the power connector.
Fully insert the power connector into the
battery chamber as shown.
397
n
4Latch the power
connector.
Rotate the latch to the closed
position (q) and fold it down
as shown (w).
To prevent the
power connector being dislodged during operation, be sure
that it is securely latched.
The battery level is not displayed in the top control panel while
the camera is powered by the AC adapter and power
connector.
398
n
Caring for the Camera
Storage
When the camera will not be used for an extended period, remove
the battery and store it in a cool, dry area with the terminal cover in
place.
To prevent mold or mildew, store the camera in a dry, well-
ventilated area.
Do not store your camera with naphtha or
camphor moth balls or in locations that:
• are poorly ventilated or subject to humidities of over 60%
• are next to equipment that produces strong electromagnetic
fields, such as televisions or radios
• are exposed to temperatures above 50 °C (122 °F) or below
–10 °C (14 °F)
Cleaning
Do not use alcohol, thinner, or other volatile chemicals.
Camera
body
Use a blower to remove dust and lint, then wipe gently with a
soft, dry cloth.
After using the camera at the beach or seaside,
wipe off sand or salt with a cloth lightly dampened in distilled
water and dry thoroughly.
Important: Dust or other foreign
matter inside the camera may cause damage not covered under
warranty.
Lens,
mirror, and
viewfinder
These glass elements are easily damaged.
Remove dust and
lint with a blower.
If using an aerosol blower, keep the can
vertical to prevent the discharge of liquid.
To remove
fingerprints and other stains, apply a small amount of lens
cleaner to a soft cloth and clean with care.
Monitor
Remove dust and lint with a blower.
When removing
fingerprints and other stains, wipe the surface lightly with a
soft cloth or chamois leather.
Do not apply pressure, as this
could result in damage or malfunction.
399
n
The Low-Pass Filter
The image sensor that acts as the camera’s picture element is fitted
with a low-pass filter to prevent moiré.
If you suspect that dirt or
dust on the filter is appearing in photographs, you can clean the
filter using the Clean image sensor option in the setup menu.
The
filter can be cleaned at any time using the Clean now option, or
cleaning can be performed automatically when the camera is
turned on or off.
❚❚ “Clean Now”
1Place the camera base down.
Image sensor cleaning is most effective
when the camera is placed base down as
shown at right.
2Select Clean image
sensor in the setup
menu.
Press G to display the
menus.
Highlight Clean
image sensor in the setup
menu and press 2.
G button
400
n
3Select Clean now.
Highlight Clean now and
press J.
The camera will check the
image sensor and then
begin cleaning. This
process takes about 7
seconds; during this time,
1 flashes in the top
control panel and other
operations can not be
performed. Do not remove
or disconnect the power
source until cleaning is
complete and 1 is no
longer displayed.
❚❚ “Clean at Startup/Shutdown”
Choose from the following options:
Option Description
5Clean at startup The image sensor is automatically cleaned each time
the camera is turned on.
6Clean at
shutdown
The image sensor is automatically cleaned during
shutdown each time the camera is turned off.
7Clean at startup
& shutdown
The image sensor is cleaned automatically at startup
and at shutdown.
Cleaning off Automatic image sensor cleaning off.
J button
401
n
1Select Clean at startup/
shutdown.
Display the Clean image
sensor menu as described in
Step 2 on the previous page.
Highlight Clean at startup/
shutdown and press 2.
2Select an option.
Highlight an option and
press J.
DImage Sensor Cleaning
Using camera controls during startup interrupts image sensor cleaning.
Cleaning is performed by vibrating the low-pass filter.
If dust can not be
fully removed using the options in the Clean image sensor menu, clean
the image sensor manually (see below) or consult a Nikon-authorized
service representative.
If image sensor cleaning is performed several times in succession, image
sensor cleaning may be temporarily disabled to protect the camera’s
internal circuitry.
Cleaning can be performed again after a short wait.
J button
402
n
❚❚ Manual Cleaning
If foreign matter can not be removed from the low-pass filter using
the Clean image sensor (0399) option in the setup menu, the
filter can be cleaned manually as described below.
Note, however,
that the filter is extremely delicate and easily damaged.
Nikon
recommends that the filter be cleaned only by Nikon-authorized
service personnel.
1Charge the battery or connect an AC adapter.
A reliable power source is required when inspecting or
cleaning the low-pass filter.
Turn the camera off and insert a
fully-charged EN-EL18 battery or connect an optional EP-6
power connector and EH-6b AC adapter.
2Remove the lens.
Turn the camera off and remove the lens.
3Select Lock mirror up
for cleaning.
Turn the camera on and
press the G button to
display the menus.
Highlight Lock mirror up
for cleaning in the setup menu and press 2 (note that this
option is not available at battery levels of J or below).
G button
403
n
4Press J.
The message shown at right will be
displayed in the monitor and a row of
dashes will appear in the top control
panel and viewfinder.
To restore normal
operation without inspecting the low-
pass filter, turn the camera off.
5Raise the mirror.
Press the shutter-release
button all the way down.
The mirror will be raised and
the shutter curtain will open,
revealing the low-pass filter.
The display in the viewfinder will
turn off and the row of dashes in the top control panel will
flash.
6Examine the low-pass filter.
Holding the camera so that light falls on
the low-pass filter, examine the filter for
dust or lint.
If no foreign objects are
present, proceed to Step 8.
404
n
7Clean the filter.
Remove any dust and lint from the filter
with a blower.
Do not use a blower-brush,
as the bristles could damage the filter.
Dirt that can not be removed with a
blower can only be removed by Nikon-authorized service
personnel.
Under no circumstances should you touch or wipe
the filter.
8Turn the camera off.
The mirror will return to the down position and the shutter
curtain will close.
Replace the lens or body cap.
DUse a Reliable Power Source
The shutter curtain is delicate and easily damaged.
If the camera powers
off while the mirror is raised, the curtain will close automatically.
To
prevent damage to the curtain, observe the following precautions:
• Do not turn the camera off or remove or disconnect the power source
while the mirror is raised.
• If the battery runs low while the mirror is raised, a beep will sound and
the self-timer lamp will flash to warn that the shutter curtain will close
and the mirror will be lowered after about two minutes.
End cleaning
or inspection immediately.
405
n
DForeign Matter on the Low-Pass Filter
Nikon takes every possible precaution to prevent foreign matter from
coming into contact with the low-pass filter during production and
shipping.
The D4, however, is designed to be used with interchangeable
lenses, and foreign matter may enter the camera when lenses are
removed or exchanged.
Once inside the camera, this foreign matter may
adhere to the low-pass filter, where it may appear in photographs taken
under certain conditions.
To protect the camera when no lens is in place,
be sure to replace the body cap provided with the camera, being careful
to first remove all dust and other foreign matter that may be adhering to
the body cap.
Avoid exchanging lenses in dusty environments.
Should foreign matter find its way onto the low-pass filter, clean the filter
as described above, or have the filter cleaned by authorized Nikon service
personnel.
Photographs affected by the presence of foreign matter on
the filter can be retouched using Capture NX 2 (available separately;
0
393) or the clean image options available in some third-party imaging
applications.
DServicing the Camera and Accessories
The camera is a precision device and requires regular servicing.
Nikon
recommends that the camera be inspected by the original retailer or
Nikon service representative once every one to two years, and that it be
serviced once every three to five years (note that fees apply to these
services).
Frequent inspection and servicing are particularly
recommended if the camera is used professionally.
Any accessories
regularly used with the camera, such as lenses or optional flash units,
should be included when the camera is inspected or serviced.
406
n
Replacing the Clock Battery
The camera clock is powered by a CR1616 lithium battery with a life
of about two years.
If the B icon is displayed in the top control
panel while the standby timer is on, the battery is running low and
needs to be replaced.
When the battery is exhausted, the B icon
will flash while the exposure meters are on.
Photographs can still
be taken but will not be stamped with the correct time and date.
Replace the battery as described below.
1Remove the main battery.
The clock battery chamber is located on the roof of the main
battery chamber.
Turn the camera off and remove the EN-EL18
battery.
2Open the clock battery chamber.
Slide the clock battery chamber cover
toward the front of the main battery
chamber.
3Remove the clock battery.
4Insert the replacement battery.
Insert a new CR1616 lithium battery so
that the positive side (the side marked
with “+” and the battery name) is visible.
407
n
5Close the clock battery chamber.
Slide the clock battery chamber cover
towards the back of the main battery
chamber until it clicks into place.
6Replace the main battery.
Reinsert the EN-EL18.
7Set the camera clock.
Set the camera to the current date and
time (031).
Until the date and time have
been set, the B icon will flash in the top
control panel.
ACAUTION
Use only CR1616 lithium batteries. Using another type of battery could
cause an explosion.
Dispose of used batteries as directed.
DInserting the Clock Battery
Insert the clock battery in the correct orientation.
Inserting the battery
incorrectly could not only prevent the clock from functioning but could
damage the camera.
408
n
Caring for the Camera and
Battery: Cautions
Do not drop: The product may malfunction if subjected to strong shocks or
vibration.
Keep dry: This product is not waterproof, and may malfunction if immersed
in water or exposed to high levels of humidity.
Rusting of the internal
mechanism can cause irreparable damage.
Avoid sudden changes in temperature: Sudden changes in temperature, such as
those that occur when entering or leaving a heated building on a cold day,
can cause condensation inside the device.
To prevent condensation, place
the device in a carrying case or plastic bag before exposing it to sudden
changes in temperature.
Keep away from strong magnetic fields: Do not use or store this device in the
vicinity of equipment that generates strong electromagnetic radiation or
magnetic fields.
Strong static charges or the magnetic fields produced by
equipment such as radio transmitters could interfere with the monitor,
damage data stored on the memory card, or affect the product’s internal
circuitry.
Do not leave the lens pointed at the sun: Do not leave the lens pointed at the sun
or other strong light source for an extended period.
Intense light may
cause the image sensor to deteriorate or produce a white blur effect in
photographs.
409
n
Cleaning: When cleaning the camera body, use a blower to gently remove
dust and lint, then wipe gently with a soft, dry cloth.
After using the
camera at the beach or seaside, wipe off any sand or salt using a cloth
lightly dampened in pure water and then dry the camera thoroughly.
In
rare instances, static electricity may cause the LCD displays to light up or
go dark.
This does not indicate a malfunction, and the display will soon
return to normal.
The lens and mirror are easily damaged.
Dust and lint should be gently
removed with a blower.
When using an aerosol blower, keep the can
vertical to prevent discharge of liquid.
To remove fingerprints and other
stains from the lens, apply a small amount of lens cleaner to a soft cloth
and wipe the lens carefully.
See “The Low-Pass Filter” (0399) for information on cleaning the low-pass
filter.
Lens contacts: Keep the lens contacts clean.
Do not touch the shutter curtain: The shutter curtain is extremely thin and easily
damaged.
Under no circumstances should you exert pressure on the
curtain, poke it with cleaning tools, or subject it to powerful air currents
from a blower.
These actions could scratch, deform, or tear the curtain.
The shutter curtain may appear to be unevenly colored, but this has no
affect on pictures and does not indicate a malfunction.
Storage: To prevent mold or mildew, store the camera in a dry, well-
ventilated area.
If you are using an AC adapter, unplug the adapter to
prevent fire.
If the product will not be used for an extended period,
remove the battery to prevent leakage and store the camera in a plastic
bag containing a desiccant.
Do not, however, store the camera case in a
plastic bag, as this may cause the material to deteriorate.
Note that
desiccant gradually loses its capacity to absorb moisture and should be
replaced at regular intervals.
To prevent mold or mildew, take the camera out of storage at least once a
month.
Turn the camera on and release the shutter a few times before
putting it away.
Store the battery in a cool, dry place.
Replace the terminal cover before
putting the battery away.
410
n
Turn the product off before removing or disconnecting the power source: Do not
unplug the product or remove the battery while the product is on or while
images are being recorded or deleted.
Forcibly cutting power in these
circumstances could result in loss of data or in damage to product memory
or internal circuitry.
To prevent an accidental interruption of power, avoid
carrying the product from one location to another while the AC adapter is
connected.
Dry the accessory shoe cover: If the camera is used in the rain, water may
penetrate the supplied BS-2 accessory shoe cover. Remove and dry the
accessory shoe cover after using the camera in the rain.
Notes on the monitor: The monitor is constructed with extremely high
precision; at least 99.99% of pixels are effective, with no more than 0.01%
being missing or defective.
Hence while these displays may contain pixels
that are always lit (white, red, blue, or green) or always off (black), this is not
a malfunction and has no effect on images recorded with the device.
Images in the monitor may be difficult to see in a bright light.
Do not apply pressure to the monitor, as this could cause damage or
malfunction.
Dust or lint on the monitor can be removed with a blower.
Stains can be removed by wiping lightly with a soft cloth or chamois
leather.
Should the monitor break, care should be taken to avoid injury
from broken glass and to prevent liquid crystal from the monitor touching
the skin or entering the eyes and mouth.
Batteries: Batteries may leak or explode if improperly handled.
Observe the
following precautions when handling batteries:
• Use only batteries approved for use in this equipment.
• Do not expose the battery to flame or excessive heat.
• Keep the battery terminals clean.
• Turn the product off before replacing the battery.
• Remove the battery from the camera or charger when not in use and
replace the terminal cover.
These devices draw minute amounts of
charge even when off and could draw the battery down to the point that
it will no longer function.
If the battery will not be used for some time,
insert it in the camera and run it flat before removing it from the camera
for storage. The battery should be stored in a cool location with an
ambient temperature of 15 to 25 °C (59 to 77 °F; avoid hot or extremely
cold locations).
Repeat this process at least once every six months.
411
n
• Turning the camera on or off repeatedly when the battery is fully
discharged will shorten battery life.
Batteries that have been fully
discharged must be charged before use.
• The internal temperature of the battery may rise while the battery is in
use.
Attempting to charge the battery while the internal temperature is
elevated will impair battery performance, and the battery may not
charge or charge only partially.
Wait for the battery to cool before
charging.
• Continuing to charge the battery after it is fully charged can impair
battery performance.
• A marked drop in the time a fully charged battery retains its charge when
used at room temperature indicates that it requires replacement.
Purchase a new EN-EL18 battery.
• Charge the battery before use.
When taking photographs on important
occasions, ready a spare EN-EL18 battery and keep it fully charged.
Depending on your location, it may be difficult to purchase replacement
batteries on short notice.
Note that on cold days, the capacity of
batteries tends to decrease.
Be sure the battery is fully charged before
taking photographs outside in cold weather.
Keep a spare battery in a
warm place and exchange the two as necessary.
Once warmed, a cold
battery may recover some of its charge.
• Used batteries are a valuable resource; recycle in accord with local
regulations.
412
n
Defaults
The default settings for the options in the camera menus are listed
below.
For information on two-button reset, see page 207.
❚❚ Playback Menu Defaults
❚❚ Shooting Menu Defaults 1
Option Default
Playback folder (0284) NC_D4
Image review (0289) Off
After delete (0290) Show next
Rotate tall (0290) On
Slide show (0291)
Image type (0291) Still images and movies
Frame interval (0291) 2 s
Audio playback (0292) On
Option Default
Extended menu banks (0295) Off
File naming (0298) DSC
Primary slot selection (095) XQD card slot
Secondary slot function (095) Overflow
Image quality (090) JPEG normal
Image size (093) Large
Image area (085)
Auto DX crop (085) On
Choose image area (086) FX (36×24)
JPEG compression (092) Size priority
NEF (RAW) recording (092)
Type Lossless compressed
NEF (RAW) bit depth 14-bit
White balance (0153) Auto > Normal
Fine-tuning (0156) A-B: 0, G-M: 0
Choose color temp. (0160) 5000 K
Preset manual (0163) d-1
Set Picture Control (0173) Standard
413
n
Color space (0299) sRGB
Active D-Lighting (0184) Off
HDR (high dynamic range) (0186)
HDR mode (0187) Off
Exposure differential (0188) Auto
Smoothing (0188) Normal
Vignette control (0300) Normal
Auto distortion control (0301) Off
Long exposure NR (0302) Off
High ISO NR (0302) Normal
ISO sensitivity settings (0117)
ISO sensitivity (0117) 100
Auto ISO sensitivity control (0119) Off
Multiple exposure (0210) 2
Multiple exposure mode (0211) Off
Number of shots (0212) 2
Auto gain (0213) On
Interval timer shooting (0216) Reset 3
Live view photography (060) Quiet
Time-lapse photography (0223) Reset 4
Movie settings (074)
Frame size/frame rate (074) 1920 × 1080; 30 fps
Movie quality (074) High quality
Microphone (075) Auto sensitivity
Destination (075) XQD card slot
ISO sensitivity range (075) 200 to 12800
1 Default settings can be restored using Shooting menu bank (0295).
With the exceptions of Extended menu banks, Multiple exposure,
Interval timer shooting, and Time-lapse photography, only settings
in the current shooting menu bank will be reset.
2 Applies to all banks.
Shooting menu reset is not available while
shooting is in progress.
3 Applies to all banks.
Start time reset to Now, interval reset to 1 minute,
number of intervals and number of shots reset to 1, and Start set to Off.
Shooting ends when reset is performed.
4 Applies to all banks. Interval reset to 5 s, recording time to 25 minutes.
Option Default
414
n
❚❚ Custom Settings Menu Defaults *
Option Default
a1 AF-C priority selection (0307) Release
a2 AF-S priority selection (0308) Focus
a3 Focus tracking with lock-on (0309) 3 (Normal)
a4 AF activation (0309) Shutter/AF-ON
a5 Focus point illumination (0310)
Manual focus mode On
Continuous mode On
Focus point brightness Normal
Dynamic-area AF display Off
a6 Focus point wrap-around (0310) No wrap
a7 Number of focus points (0311) 51 points
a8 Assign AF-ON button (0311) AF-ON
a9 Assign AF-ON button (vert.) (0312) AF-ON
a10 Store points by orientation (0312) No
b1 ISO sensitivity step value (0313) 1/3 step
b2 EV steps for exposure cntrl (0313) 1/3 step
b3 Exp./flash comp. step value (0313) 1/3 step
b4 Easy exposure compensation (0314) Off
b5 Center-weighted area (0315) ø 12 mm
b6 Fine-tune optimal exposure (0315)
Matrix metering 0
Center-weighted metering 0
Spot metering 0
c1 Shutter-release button AE-L (0316) Off
c2 Standby timer (0316) 6 s
c3 Self-timer (0317)
Self-timer delay 10 s
Number of shots 1
Interval between shots 0.5 s
415
n
c4 Monitor off delay (0317)
Playback 10 s
Menus 20 s
Information display 10 s
Image review 4 s
Live view 10 min
d1 Beep (0318)
Volume Off
Pitch High
d2 Shooting speed (0318)
Continuous high-speed 10 fps
Continuous low-speed 5 fps
d3 Max. continuous release (0319) 200
d4 Exposure delay mode (0319) Off
d5 File number sequence (0320) On
d6 Viewfinder grid display (0321) Off
d7 Control panel/viewfinder (0321)
Rear control panel ISO sensitivity
Viewfinder display Frame count
d8 Screen tips (0321) On
d9 Information display (0322) Auto
d10 LCD illumination (0322) Off
e1 Flash sync speed (0323) 1/250 s
e2 Flash shutter speed (0324) 1/60 s
e3 Optional flash (0324) TTL
e4 Exposure comp. for flash (0325) Entire frame
e5 Modeling flash (0325) On
e6 Auto bracketing set (0325) AE & flash
e7 Auto bracketing (Mode M) (0326) Flash/speed
e8 Bracketing order (0326) MTR > under > over
f1 Multi selector center button (0327)
Shooting mode Select center focus point
Playback mode Thumbnail on/off
Live view Select center focus point
Option Default
416
n
f2 Multi selector (0328) Do nothing
f3 Assign Fn button (0328)
Press (0329) None
Press + command dials (0332) Choose image area
f4 Assign preview button (0333)
Press Preview
Press + command dials None
f5 Assign sub-selector (0333) Focus point selection
f6 Assign sub-selector center (0333)
Press AE/AF lock
Press + command dials None
f7 Assign Fn button (vert.) (0334)
Press AE/AF lock
Press + command dials None
f8 Shutter spd & aperture lock (0334)
Shutter speed lock Off
Aperture lock Off
f9 Assign BKT button (0335) Auto bracketing
f10 Customize command dials (0336)
Reverse rotation Exposure compensation: U
Shutter speed/aperture: U
Change main/sub Off
Aperture setting Sub-command dial
Menus and playback Off
f11 Release button to use dial (0337) No
f12 Slot empty release lock (0338) Enable release
f13 Reverse indicators (0338)
f14 Assign multi selector (vert.) (0338) Same as multi selector
f15 Playback zoom (0339) Use X and W
f16 Assign movie record button (0339)
Press + command dials None
g1 Assign Fn button (0340)
Press None
Option Default
417
n
❚❚ Setup Menu Defaults
g2 Assign preview button (0341)
Press Index marking
g3 Assign sub-selector center (0342)
Press AE/AF lock
g4 Assign shutter button (0343) Take photos
* Defaults for the current Custom Settings bank can be restored using
Custom settings bank (0305).
Option Default
Monitor brightness (0345) Manual
Manual 0
Clean image sensor (0399)
Clean at startup/shutdown (0400) Clean at startup & shutdown
HDMI (0281)
Output resolution Auto
Advanced
Output range Auto
Output display size 95%
Live view on-screen display On
Flicker reduction (0348) Auto
Time zone and date (0348)
Daylight saving time Off
Auto image rotation (0350) On
Voice memo options (0255)
Voice memo (0255) Off
Voice memo overwrite (0256) Disable
Voice memo button (0256) Press and hold
Audio output (0261) Speaker/headphones
GPS (0233)
Standby timer Enable
Use GPS to set camera clock Yes
Option Default
418
n
Exposure Program
The exposure program for programmed auto (0126) is shown in
the following graph:
The maximum and minimum values for EV vary with ISO sensitivity;
the above graph assumes an ISO sensitivity of ISO 100 equivalent.
When matrix metering is used, values over 16 1/3EV are reduced to
16 1/3EV.
-4
-3
12
13
-2
-1
0
1
2
3
4
5
6
7
8
9
10
11
f/1.4
f/1
f/2
f/2.8
f/4
f/5.6
f/8
f/11
f/16
f/22
f/32 30" 15" 8" 4" 2" 1" 1/21/41/81/15 1/30 1/60
1
/
125 1
/
250 1
/
500
1
/
1000 1
/
2000 1
/
4000 1
/
8000
22
21
20
19
18
17
16
15
14
[EV]
23
161/3
f/1.4 − f/16
Shutter speed
Aperture
ISO 100; lens with maximum aperture of f/1.4 and minimum
aperture of f/16 (e.g., AF-S NIKKOR 50mm f/1.4G)
419
n
Troubleshooting
If the camera fails to function as expected, check the list of
common problems below before consulting your retailer or Nikon
representative.
❚❚ Display
Viewfinder is out of focus: Adjust viewfinder focus or use optional diopter
adjustment lenses (038, 392).
Viewfinder is dark: Insert a fully-charged battery (023, 40).
Displays turn off without warning: Choose longer delays for Custom Setting c2
(Standby timer) or c4 (Monitor off delay) (0316, 317).
Displays in control panels or viewfinder are unresponsive and dim: The response
times and brightness of these displays vary with temperature.
AIf the Camera Stops Responding
In extremely rare instances, the displays may not respond as expected
and the camera may stop functioning. In most cases, this phenomenon
is caused by a strong external static charge.
Turn the camera off, remove
and replace the battery, taking care to avoid burns, and turn the camera
on again, or, if you are using an AC adapter (available separately),
disconnect and reconnect the adapter and turn the camera on again.
If
the problem persists, contact your retailer or Nikon-authorized service
representative.
420
n
❚❚ Shooting
Camera takes time to turn on: Delete files or folders.
Shutter-release disabled:
• Memory card is full (033, 41).
•Release locked is selected for Custom Setting f12 (Slot empty release
lock; 0338) and no memory card is inserted (033).
• CPU lens with aperture ring attached but aperture not locked at highest
f-number.
If B is displayed in the top control panel, select Aperture
ring for Custom Setting f10 (Customize command dials) > Aperture
setting to use lens aperture ring to adjust aperture (0336).
• Exposure mode f selected with A selected for shutter speed
(0425).
Camera is slow to respond to shutter-release button: Select Off for Custom Setting
d4 (Exposure delay mode; 0319).
Only one shot taken each time shutter-release button is pressed in continuous release
mode: Turn HDR off (0186).
Photos are out of focus:
• Rotate focus-mode selector to AF (097).
• Camera unable to focus using autofocus: use manual focus or focus lock
(0105, 108).
Full range of shutter speeds not available: Flash in use.
Flash sync speed can be
selected using Custom Setting e1 (Flash sync speed); when using
compatible flash units, choose 1/250 s (Auto FP) for full range of shutter
speeds (0323).
Focus does not lock when shutter-release button is pressed halfway: Camera is in
focus mode AF-C: use the center of the sub-selector to lock focus (0105).
Can not select focus point:
• Unlock focus selector lock (0103).
• Auto-area or face-priority AF selected for AF-area mode; choose another
mode (0100).
• Camera is in playback mode (0235).
• Menus are in use (0283).
• Press shutter-release button halfway to start standby timer (045).
Image size can not be changed: Image quality set to NEF (RAW) (090).
Camera is slow to record photos: Turn long exposure noise reduction off
(0302).
421
n
Flicker or banding appear during live view or movie recording: Choose an option for
Flicker reduction that matches the frequency of the local AC power
supply (0348).
Bright bands appear during live view or movie recording: A flashing sign, flash, or
other light source with brief duration was used during live view or movie
recording.
Noise (bright spots, randomly-spaced bright pixels, fog, lines, or reddish areas) appears in
photos:
• To reduce randomly-spaced bright pixels, fog, or lines, choose lower ISO
sensitivity or use high ISO noise reduction (0117, 302).
• To reduce bright spots, randomly-spaced bright pixels, or fog at shutter
speeds slower than 1 s or to reduce reddish areas and other artifacts in
long time-exposures, enable long exposure noise reduction (0302).
• Turn Active D-Lighting off to avoid heightening the effects of noise
(0184).
Photos are blotched or smeared:
•Clean lens.
• Clean low-pass filter (0399).
Colors are unnatural:
• Adjust white balance to match light source (0153).
• Adjust Set Picture Control settings (0173).
Can not measure white balance: Subject is too dark or too bright (0164).
Image can not be selected as source for preset white balance: Image was not created
with D4 (0168).
White balance bracketing unavailable:
• NEF (RAW) or NEF+JPEG image quality option selected for image quality
(090).
• Multiple exposure mode is in effect (0210).
Effects of Picture Control differ from image to image: A (auto) is selected for
sharpening, contrast, or saturation.
For consistent results over a series of
photographs, choose a setting other than A (auto) (0177).
Metering can not be changed: Autoexposure lock is in effect (0136).
Exposure compensation can not be used: Choose exposure mode e, f, or g
(0125, 138).
Sound is not recorded with movies: Microphone off is selected for Movie
settings > Microphone (075).
422
n
❚❚ Playback
NEF (RAW) image is not played back: Photo was taken at image quality of NEF +
JPEG (091).
Can not view pictures recorded with other cameras: Pictures recorded with other
makes of camera may not be displayed correctly.
Some photos are not displayed during playback: Select All for Playback folder
(0284).
“Tall” (portrait) orientation photos are displayed in “wide” (landscape) orientation:
• Select On for Rotate tall (0290).
• Photo was taken with Off selected for Auto image rotation (0350).
• Photo is displayed in image review (0289).
• Camera was pointed up or down when photo was taken (0350).
Can not delete photo: Picture is protected.
Remove protection (0249).
Can not retouch picture: Picture was not created with D4 (0362).
Message is displayed stating that no images are available for playback: Select All for
Playback folder (0284).
Can not change print order: Memory card is full: delete photos (041, 251).
Can not select photo for printing: Photo is in NEF (RAW) format.
Create JPEG
copy using NEF (RAW) processing (0372) or transfer to computer and
print using ViewNX 2 (supplied) or Capture NX 2 (available separately;
0393).
Can not print photos: NEF (RAW) and TIFF photos can not be printed by direct
USB connection.
Use DPOF print service (TIFF images only), create JPEG
copy using NEF (RAW) processing (0372), or transfer to computer and
print using ViewNX 2 (supplied) or Capture NX 2 (available separately;
0393).
Photo is not displayed on high-definition video device: Confirm that HDMI cable
(available separately) is connected (0280).
Photos are not displayed in Capture NX 2: Update to the latest version (0393).
423
n
❚❚ Miscellaneous
Image Dust Off option in Capture NX 2 does not have desired effect: Image sensor
cleaning changes the position of dust on the low-pass filter. Dust off
reference data recorded before image sensor cleaning is performed can
not be used with photographs taken after image sensor cleaning is
performed. Dust off reference data recorded after image sensor cleaning is
performed can not be used with photographs taken before image sensor
cleaning is performed (0347).
Computer displays NEF (RAW) images differently from camera: Third-party software
does not display effects of Picture Controls, Active D-Lighting, or vignette
control.
Use ViewNX 2 (supplied) or optional Nikon software such as
Capture NX 2 (available separately).
Can not transfer photos to computer: OS not compatible with camera or transfer
software.
Use card reader to copy photos to computer (0266).
Date of recording is not correct: Set camera clock (031).
Menu item can not be selected: Some options are not available at certain
combinations of settings or when no memory card is inserted. Note that
Battery info option is not available when camera is powered by an
optional EP-6 power connector and EH-6b AC adapter (0351).
424
n
Error Messages
This section lists the indicators and error messages that appear in
the viewfinder, top control panel, and monitor.
Indicator
Problem Solution 0
Control
panel
View-
finder
B
(flashes)
Lens aperture ring is
not set to minimum
aperture.
Set ring to minimum
aperture (highest
f-number).
29
HdLow battery. Ready a fully-charged
spare battery. 40
H
(flashes)
d
(flashes)
• Battery exhausted. • Recharge or replace
battery.
xix, 23,
25, 391
• Battery can not be
used.
• Contact Nikon-
authorized service
representative.
• An extremely
exhausted
rechargeable Li-ion
battery or a third-
party battery is
inserted in the
camera.
• Replace the battery,
or recharge the
battery if the
rechargeable Li-ion
battery is exhausted.
• High battery
temperature.
• Remove battery and
wait for it to cool.
—
B
(flashes) — Camera clock is not set. Set camera clock. 31
425
n
F
No lens attached, or
non-CPU lens attached
without specifying
maximum aperture.
Aperture shown in
stops from maximum
aperture.
Aperture value will be
displayed if maximum
aperture is specified.
228
—24
(flashes)
Camera unable to focus
using autofocus.
Change composition or
focus manually. 43, 108
(Exposure
indicators and
shutter speed
or aperture
display flash)
Subject too bright;
photo will be
overexposed.
• Use a lower ISO
sensitivity.
117
• Use optional ND filter.
In exposure mode:
393
fIncrease shutter
speed
127
gChoose a smaller
aperture (higher
f-number)
128
Subject too dark; photo
will be underexposed.
• Use a higher ISO
sensitivity.
117
• Use optional flash. In
exposure mode:
191
fLower shutter
speed
127
gChoose a larger
aperture (lower
f-number)
128
A
(flashes)
A selected in
exposure mode f.
Change shutter speed
or select manual
exposure mode.
127,
129
1
(flashes)
k
(flashes) Processing in progress. Wait until processing is
complete. —
Indicator
Problem Solution 0
Control
panel
View-
finder
426
n
—c
(flashes)
If indicator flashes for
3s after flash fires,
photo may be
underexposed.
Check photo in
monitor; if
underexposed, adjust
settings and try again.
195
Y
(flashes) —
Flash unit that does not
support red-eye
reduction attached and
flash sync mode set to
red-eye reduction.
Change flash sync
mode or use flash unit
that supports red-eye
reduction.
193
n
i/j
(flashes)
j
(flashes)
Memory insufficient to
record further photos
at current settings, or
camera has run out of
file or folder numbers.
• Reduce quality or
size.
90, 93
• Delete photographs
after copying
important images to
computer or other
device.
251,
263
• Insert new memory
card.
33
O
(flashes) Camera malfunction.
Release shutter.
If error
persists or appears
frequently, consult
Nikon-authorized
service representative.
—
AThe i and j Icons
These icons flash to show the card affected.
Indicator
Problem Solution 0
Control
panel
View-
finder
427
n
Indicator
Problem Solution 0Monitor
Control
panel
No memory card. S
Camera cannot
detect memory
card.
Turn camera off and
confirm that card is
correctly inserted.
33
This memory
card cannot be
used.
Card may be
damaged.
Insert
another card.
W,
R
i/j
(flashes)
• Error accessing
memory card.
• Use Nikon-
approved card.
442
• Check that contacts
are clean.
If card is
damaged, contact
retailer or Nikon
representative.
—
• Unable to create
new folder.
• Delete files or insert
new memory card
after copying
important images
to computer or
other device.
33,
251,
263
This card is not
formatted.
Format the card.
[C]
(flashes)
Memory card has
not been
formatted for use
in camera.
Format memory card
or insert new memory
card.
33, 36
Failed to update
flash unit
firmware.
Flash cannot be
used.
Contact a Nikon-
authorized
service
representative.
—
Firmware for flash
unit mounted on
camera was not
updated correctly.
Contact a Nikon-
authorized service
representative.
—
428
n
Unable to start
live view. Please
wait.
—
The internal
temperature of
the camera is
high.
Wait for the internal
circuits to cool before
resuming live view or
movie recording.
62, 73
Folder contains
no images. —
No images on
memory card or in
folder(s) selected
for playback.
Select folder
containing images
from Playback folder
menu or insert
memory card
containing images.
33, 284
All images are
hidden. —
All photos in
current folder are
hidden.
No images can be
played back until
another folder has
been selected or Hide
image used to allow
at least one image to
be displayed.
284
Cannot display
this file. —
File has been
created or
modified using a
computer or
different make of
camera, or file is
corrupt.
File can not be played
back on camera. —
Cannot select
this file. —
Selected image
can not be
retouched.
Images created with
other devices can not
be retouched.
362
Check printer. — Printer error.
Check printer.
To
resume, select
Continue (if
available).
272 *
Indicator
Problem Solution 0Monitor
Control
panel
429
n
Check paper. —
Paper in printer is
not of selected
size.
Insert paper of correct
size and select
Continue.
272 *
Paper jam. —Paper is jammed
in printer.
Clear jam and select
Continue.272 *
Out of paper. —Printer is out of
paper.
Insert paper of
selected size and
select Continue.
272 *
Check ink supply. —Ink error. Check ink.
To resume,
select Continue.272 *
Out of ink. —Printer is out of
ink.
Replace ink and select
Continue.272 *
* See printer manual for more information.
Indicator
Problem Solution 0Monitor
Control
panel
430
n
Specifications
❚❚ Nikon D4 Digital Camera
Type
Type Single-lens reflex digital camera
Lens mount Nikon F mount (with AF coupling and AF contacts)
Effective pixels
Effective pixels 16.2 million
Image sensor
Image sensor 36.0 × 23.9 mm CMOS sensor (Nikon FX format)
Total pixels 16.6 million
Dust-reduction System Image sensor cleaning, Image Dust Off reference data
(requires optional Capture NX 2 software)
Storage
Image size (pixels) • FX (36×24) image area
4,928
×
3,280 (#)3,696
×
2,456 ($)2,464
×
1,640 (%)
• 1.2× (30×20) image area
4,096
×
2,720 (#)3,072
×
2,040 ($) 2,048
×
1,360 (%)
• DX (24×16) image area
3,200
×
2,128 (#)2,400
×
1,592 ($) 1,600
×
1,064 (%)
• 5 : 4 (30×24) image area
4,096
×
3,280 (#)3,072
×
2,456 ($) 2,048
×
1,640 (%)
• FX-format photographs taken in movie live view (16:9)
4,928
×
2,768 (#)3,696
×
2,072 ($) 2,464
×
1,384 (%)
• DX-format photographs taken in movie live view (16:9)
3,200
×
1,792 (#)2,400
×
1,344 ($) 1,600
×
896 (%)
• FX-format photographs taken in movie live view (3:2)
4,928
×
3,280 (#)3,696
×
2,456 ($) 2,464
×
1,640 (%)
• DX-format photographs taken in movie live view (3:2)
3,200
×
2,128 (#)2,400
×
1,592 ($) 1,600
×
1,064 (%)
Note: A DX-based format is used for photographs taken
using the DX (24 × 16) 1.5× image area; an FX-based
format is used for all other photographs.
431
n
File format •NEF (RAW): 12 or 14 bit, lossless compressed,
compressed, or uncompressed
•TIFF (RGB)
•JPEG: JPEG-Baseline compliant with fine (approx. 1 : 4),
normal (approx. 1 : 8), or basic (approx. 1 : 16)
compression (Size priority); Optimal quality
compression available
•NEF (RAW)+JPEG: Single photograph recorded in both
NEF (RAW) and JPEG formats
Picture Control System Can be selected from Standard, Neutral, Vivid,
Monochrome, Portrait, Landscape; selected Picture
Control can be modified; storage for custom Picture
Controls
Media XQD and Type I CompactFlash memory cards (UDMA
compliant)
Dual card slots Either card can be used for primary or backup storage
or for separate storage of NEF (RAW) and JPEG images;
pictures can be copied between cards.
File system DCF (Design Rule for Camera File System) 2.0, DPOF
(Digital Print Order Format), Exif (Exchangeable Image
File Format for Digital Still Cameras) 2.3, PictBridge
Viewfinder
Viewfinder Eye-level pentaprism single-lens reflex viewfinder
Frame coverage
•
FX (36×24)
: Approx. 100% horizontal and 100% vertical
•1.2× (30×20): Approx. 97% horizontal and 97% vertical
•DX (24×16): Approx. 97% horizontal and 97% vertical
•5:4 (30×24): Approx. 97% horizontal and 100% vertical
Magnification Approx. 0.7 × (50 mm f/1.4 lens at infinity, –1.0 m–1)
Eyepoint 18 mm (–1.0 m–1; from center surface of viewfinder
eyepiece lens)
Diopter adjustment –3–+1 m–1
Focusing screen Type B BriteView Clear Matte Mark VIII screen with AF
area brackets and framing grid
Storage
432
n
Reflex mirror Quick return
Depth-of-field preview When Pv button is pressed, lens aperture is stopped
down to value selected by user (g and h modes) or by
camera (e and f modes)
Lens aperture Instant return, electronically controlled
Lens
Compatible lenses Compatible with AF NIKKOR lenses, including type G
and D lenses (some restrictions apply to PC Micro-
NIKKOR lenses) and DX lenses (using DX 24 × 16 1.5×
image area), AI-P NIKKOR lenses, and non-CPU AI
lenses (exposure modes g and h only). IX NIKKOR
lenses, lenses for the F3AF, and non-AI lenses can
not be used.
The electronic rangefinder can be used with lenses
that have a maximum aperture of f/5.6 or faster (the
electronic rangefinder supports the 11 focus points
with lenses that have a maximum aperture of f/8 or
faster).
Shutter
Type Electronically-controlled vertical-travel focal-plane
shutter
Speed 1/8000 – 30 s in steps of 1/3, 1/2, or 1 EV, bulb, X250
Flash sync speed X=1/250 s; synchronizes with shutter at 1/250 s or slower
Release
Release mode S (single frame), CL (continuous low speed),
CH(continuous high speed), J (quiet shutter-release),
E(self-timer), MUP (mirror up)
Approximate frame
advance rate Up to 10 fps (CL) or 10–11 fps (CH)
Self-timer 2 s, 5 s, 10 s, 20 s; 1–9 exposures at intervals of 0.5, 1, 2,
or 3 s
Viewfinder
433
n
Exposure
Metering TTL exposure metering using RGB sensor with
approximately 91K (91,000) pixels
Metering method •Matrix: 3D color matrix metering III (type G and D
lenses); color matrix metering III (other CPU lenses);
color matrix metering available with non-CPU lenses
if user provides lens data
•Center-weighted: Weight of 75% given to 12 mm circle
in center of frame.
Diameter of circle can be changed
to 8, 15, or 20 mm, or weighting can be based on
average of entire frame (non-CPU lenses use 12-mm
circle or average of entire frame)
•Spot: Meters 4 mm circle (about 1.5% of frame)
centered on selected focus point (on center focus
point when non-CPU lens is used)
Range (ISO 100, f/1.4
lens, 20 °C/68 °F)
•Matrix or center-weighted metering: –1–+20 EV
•Spot metering: 2–20 EV
Exposure meter coupling Combined CPU and AI
Exposure mode Programmed auto with flexible program (e); shutter-
priority auto (f); aperture-priority auto (g); manual (h)
Exposure compensation –5 – +5 EV in increments of 1/3, 1/2, or 1 EV
Exposure bracketing 2–9 frames in steps of 1/3, 1/2, 2/3, or 1 EV
Flash bracketing 2–9 frames in steps of 1/3, 1/2, 2/3, or 1 EV
White balance
bracketing 2–9 frames in steps of 1, 2, or 3
ADL bracketing 2 frames using selected value for one frame or 3–5
frames using preset values for all frames
Exposure lock Luminosity locked at detected value with the center of
the sub-selector
ISO sensitivity
(Recommended
Exposure Index)
ISO 100 – 12800 in steps of 1/3, 1/2, or 1 EV.
Can also be
set to approx. 0.3, 0.5, 0.7, or 1 EV (ISO 50 equivalent)
below ISO 100 or to approx. 0.3, 0.5, 0.7, 1, 2, 3, or 4 EV
(ISO 204800 equivalent) above ISO 12800; auto ISO
sensitivity control available
Active D-Lighting Can be selected from Auto, Extra high +2/+1, High,
Normal, Low, or Off
434
n
Focus
Autofocus Nikon Advanced Multi-CAM 3500FX autofocus sensor
module with TTL phase detection, fine-tuning, and 51
focus points (including 15 cross-type sensors; f/8
supported by 11 sensors)
Detection range –2 – +19 EV (ISO 100, 20 °C/68 °F)
Lens servo •Autofocus (AF): Single-servo autofocus (AF-S);
continuous-servo autofocus (AF-C); predictive focus
tracking automatically activated according to subject
status
•Manual focus (M): Electronic rangefinder can be used
Focus point Can be selected from 51 or 11 focus points
AF-area mode Single-point AF, 9-, 21-, or 51- point dynamic-area AF,
3D-tracking, auto-area AF
Focus lock Focus can be locked by pressing shutter-release button
halfway (single-servo autofocus) or by pressing the
center of the sub-selector
Flash
Flash control TTL: i-TTL flash control using RGB sensor with
approximately 91K (91,000) pixels is available with
SB-910, SB-900, SB-800, SB-700, SB-600, or SB-400; i-TTL
balanced fill-flash for digital SLR is used with matrix
and center-weighting metering, standard i-TTL flash
for digital SLR with spot metering
Flash mode Front curtain sync, slow sync, rear-curtain sync, red-eye
reduction, red-eye reduction with slow sync, slow rear-
curtain sync, Auto FP High-Speed Sync supported
Flash compensation –3 – +1 EV in increments of 1/3, 1/2, or 1 EV
Flash-ready indicator Lights when optional flash unit is fully charged; flashes
after flash is fired at full output
Accessory shoe ISO 518 hot-shoe with sync and data contacts and
safety lock
435
n
Nikon Creative Lighting
System (CLS)
Advanced Wireless Lighting supported with SB-910,
SB-900, SB-800, or SB-700 as a master flash, and SB-600
or SB-R200 as remotes, or SU-800 as commander; Auto
FP High-Speed Sync and modeling illumination
supported with all CLS-compatible flash units except
SB-400; Flash Color Information Communication and
FV lock supported with all CLS-compatible flash units
Sync terminal ISO 519 sync terminal with locking thread
White balance
White balance
Auto (2 types), incandescent, fluorescent (7 types), direct
sunlight, flash, cloudy, shade, preset manual (up to 4
values can be stored), choose color temperature
(2500 K–10000 K), all with fine-tuning.
Live view
Modes Live view photography (quiet or silent), movie live view
Lens servo •Autofocus (AF): Single-servo autofocus (AF-S); full-time
servo autofocus (AF-F)
•Manual focus (M)
AF-area mode Face-priority AF, wide-area AF, normal-area AF, subject-
tracking AF
Autofocus Contrast-detect AF anywhere in frame (camera selects
focus point automatically when face-priority AF or
subject-tracking AF is selected)
Movie
Metering TTL exposure metering using main image sensor
Frame size (pixels) and
frame rate
• 1,920 × 1,080; 30 p (progressive), 25 p, 24 p
• 1,920 × 1,080 crop; 30 p, 25 p, 24 p
• 1,280 × 720; 60 p, 50 p, 30 p, 25 p
• 640 × 424; 30p, 25p
Actual frame rates for 60 p, 50 p, 30 p, 25 p, and 24 p are
59.94, 50, 29.97, 25, and 23.976 fps respectively; all
options support both ★ high and normal image
quality
Flash
436
n
File format MOV
Video compression H.264/MPEG-4 Advanced Video Coding
Audio recording format Linear PCM
Audio recording device Built-in monaural or external stereo microphone;
sensitivity adjustable
ISO sensitivity Automatically adjusted in the range ISO 200–12800 or
ISO 200–Hi 4
Other options Index marking, time-lapse photography
Monitor
Monitor 8-cm/3.2-in., approx. 921k-dot (VGA) TFT LCD with
170 ° viewing angle, approximately 100% frame
coverage, and automatic monitor brightness control
using ambient brightness sensor
Playback
Playback Full-frame and thumbnail (4, 9, or 72 images) playback
with playback zoom, movie playback, photo and/or
movie slide shows, histogram display, highlights,
photo information, GPS data display, auto image
rotation, voice memo input and playback, and IPTC
information embedding and display
Interface
USB Hi-Speed USB
HDMI output Type C mini-pin HDMI connector; can be used
simultaneously with camera monitor
Audio input Stereo mini-pin jack (3.5mm diameter; plug-in power
supported)
Audio output Stereo mini-pin jack (3.5mm diameter)
Ten-pin remote terminal Can be used to connect optional remote control, GP-1
GPS unit, or GPS device compliant with NMEA0183
version 2.01 or 3.01 (requires optional MC-35 GPS
adapter cord and cable with D-sub 9-pin connector)
Ethernet RJ-45 connector
Peripheral connector For WT-5
Movie
437
n
• Unless otherwise stated, all figures are for a camera with a fully-charged
battery operating at an ambient temperature of 20 °C (68 °F).
• Nikon reserves the right to change the specifications of the hardware and
software described in this manual at any time and without prior notice.
Nikon will not be held liable for damages that may result from any mistakes
that this manual may contain.
Supported languages
Supported languages Arabic, Chinese (Simplified and Traditional), Czech,
Danish, Dutch, English, Finnish, French, German,
Indonesian, Italian, Japanese, Korean, Norwegian,
Polish, Portuguese, Romanian, Russian, Spanish,
Swedish, Thai, Turkish, Ukrainian
Power source
Battery One rechargeable Li-ion EN-EL18 battery
AC adapter EH-6b AC adapter; requires EP-6 power connector
(available separately)
Tripod socket
Tripod socket 1/4 in. (ISO 1222)
Dimensions/weight
Dimensions (W×H×D) Approx. 160 × 156.5 × 90.5 mm (6.3 × 6.2 × 3.6 in.)
Weight Approx. 1340 g (2 lb. 15.3 oz.) with battery and XQD
memory card but without body cap and accessory
shoe cover; approx. 1180 g/2 lb. 9.6 oz. (camera body
only)
Operating environment
Temperature 0–40 °C (+32–104 °F)
Humidity 85% or less (no condensation)
438
n
MH-26 battery charger
Rated input AC 100 to 240 V, 50/60 Hz
Charging output DC 12.6 V/1.2 A
Applicable batteries Nikon EN-EL18 rechargeable Li-ion batteries
Charging time per
battery
Approx. 2 hours and 20 minutes at ambient
temperature of 25 °C (77 °F) when no charge remains
Operating temperature 0–40 °C (+32–104 °F)
Dimensions (W × H × D) Approx. 160 × 85 × 50.5 mm (6.3 × 3.3 × 2 in.)
Length of power cable Approx. 1.8 m/6 ft (U.S.A. and Canada) or 1.5 m/4.9 ft
(other countries)
Weight Approx. 265 g (9.3 oz), excluding power cable
EN-EL18 rechargeable Li-ion battery
Type Rechargeable lithium-ion battery
Rated capacity 10.8 V/2,000 mAh
Operating temperature 0–40 °C (+32–104 °F)
Dimensions (W × H × D) Approx. 56.5 × 27 × 82.5 mm (2.2 × 1.1 × 3.2 in.)
Weight Approx. 160 g (5.6 oz), excluding terminal cover
439
n
ASupported Standards
•DCF Version 2.0: The Design Rule for Camera File System (DCF) is a
standard widely used in the digital camera industry to ensure
compatibility among different makes of camera.
•DPOF: Digital Print Order Format (DPOF) is an industry-wide standard
that allows pictures to be printed from print orders stored on the
memory card.
•Exif version 2.3: The camera supports Exif (Exchangeable Image File
Format for Digital Still Cameras) version 2.3, a standard in which
information stored with photographs is used for optimal color
reproduction when the images are output on Exif-compliant printers.
•PictBridge: A standard developed through cooperation with the digital
camera and printer industries, allowing photographs to be output
directly to a printer without first transferring them to a computer.
•HDMI: High-Definition Multimedia Interface is a standard for
multimedia interfaces used in consumer electronics and AV devices
capable of transmitting audiovisual data and control signals to HDMI-
compliant devices via a single cable connection.
ATrademark Information
Macintosh, Mac OS, and QuickTime are registered trademarks of Apple
Inc. in the United States and/or other countries. Microsoft, Windows and
Windows Vista are either registered trademarks, or trademarks of
Microsoft Corporation in the United States and/or other countries.
XQD
is a trademark of Sony Corporation.
CompactFlash is a trademark of
SanDisk Corporation.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
PictBridge is a trademark. All other trade names mentioned in this
manual or the other documentation provided with your Nikon product
are trademarks or registered trademarks of their respective holders.
440
n
Calibrating Batteries
The MH-26 battery charger is equipped with a battery calibration
feature.
Calibrate the battery as required to ensure the accuracy of
the camera and charger battery level displays.
If the calibration lamp for the current
battery chamber flashes when a
battery is inserted, the battery needs
to be calibrated.
To begin
calibration, press the calibration
button for the current chamber for
about a second.
The time needed to
calibrate the battery is shown by the
charge and calibration lamps:
When calibration is complete, the calibration and charge lamps will
turn off and charging will begin immediately.
Although calibration is recommended for accurate measurement
of battery charge state, calibration need not be performed when
the calibration lamp flashes.
Once begun, calibration can be
interrupted as desired.
• If the calibration button is not pressed while the calibration lamp
is flashing, normal charging will begin after about ten seconds.
• To interrupt calibration, press the calibration button again.
Calibration will end and charging will begin.
Approximate time needed
to recalibrate battery
Calibration
lamp
Charge lamps
2 h 4 h 6 h
Over 6 hours K (glows) K (glows) K (glows) K (glows)
4 – 6 hours K (glows) K (glows) K (glows) JK (off)
2 – 4 hours K (glows) K (glows) JK (off) JK (off)
Under 2 hours K (glows) JK (off ) JK (off) JK (off )
Chamber
lamps (green)
Charge lamps
(green)
Calibration
lamps (yellow)
Calibration
buttons
441
n
ABattery Warning
If the chamber and calibration lamps flash on and off in sequence when
no battery is inserted, there is a problem with the charger. If the
chamber and calibration lamps flash on and off in sequence when a
battery is inserted, a problem has occurred with the battery or charger
during charging. Remove the battery, unplug the charger, and take the
battery and charger to a Nikon-authorized service representative for
inspection.
ACharging and Calibrating Two Batteries
The MH-26 charges only one battery at a time.
If batteries are inserted in
both chambers, they will be charged in the order inserted.
If the
calibration button for the first battery is pressed, the second battery can
not be calibrated or charged until calibration and charging of the first
battery are complete.
442
n
Approved Memory Cards
The camera accepts the XQD and CompactFlash memory cards
listed in the following sections.
Other cards have not been tested.
For more details on the cards listed below, please contact the
manufacturer.
❚❚ XQD Memory Cards
The following XQD memory cards have been tested and approved
for use in the camera.
Sony
S series QD-S32 32 GB
QD-S64 64 GB
H series QD-H16 16 GB
QD-H32 32 GB
443
n
❚❚ CompactFlash Memory Cards
The following Type I CompactFlash memory cards have been
tested and approved for use in the camera.
Type II cards and
microdrives can not be used.
SanDisk
Extreme Pro SDCFXP 16 GB, 32 GB, 64 GB, 128 GB
Extreme SDCFX 8 GB, 16 GB, 32 GB
Extreme IV SDCFX4 2GB, 4GB, 8GB, 16GB
Extreme III SDCFX3 2GB, 4GB, 8GB, 16GB
Ultra II SDCFH 2GB, 4GB, 8GB
Standard SDCFB 2GB, 4GB
Lexar
Media
Professional UDMA
1000 × 16 GB, 32 GB, 64 GB, 128 GB
600 × 8 GB, 16 GB, 32 GB
400 × 8 GB, 16 GB, 32 GB
300 × 2GB, 4GB, 8GB, 16 GB
Professional
233 × 2GB, 4GB, 8GB
133 × 2GB, 4GB, 8GB
80 × 2GB, 4GB
Platinum II 80 × 2GB, 4GB, 8GB, 16GB
60 × 4GB
444
n
Memory Card Capacity
The following table shows the approximate number of pictures
that can be stored on a Sony H-series QD-H32 XQD card at different
image quality, image size, and image area settings.
❚❚ FX (36×24) Image Area*
* Includes images taken with non-DX lenses when On is selected for Auto DX
crop.
Image quality Image size File size 1No.
of images 1Buffer capacity 2
NEF (RAW), Lossless
compressed, 12-bit
—15.4 MB 1100 92
NEF (RAW), Lossless
compressed, 14-bit
—19.4 MB 872 75
NEF (RAW),
Compressed, 12-bit
—13.9 MB 1500 98
NEF (RAW),
Compressed, 14-bit
—17.0 MB 1200 76
NEF (RAW),
Uncompressed,
12-bit
—26.5 MB 1100 77
NEF (RAW),
Uncompressed,
14-bit
—34.3 MB 872 69
TIFF (RGB)
Large 49.1 MB 612 55
Medium 28.3 MB 1000 59
Small 13.2 MB 2200 66
JPEG fine 3
Large 7.9 MB 2900 170
Medium 5.4 MB 4600 200
Small 3.0 MB 8500 200
JPEG normal3
Large 4.5 MB 5600 182
Medium 2.8 MB 9000 200
Small 1.6 MB 15700 200
JPEG basic 3
Large 2.2 MB 10800 200
Medium 1.5 MB 16800 200
Small 0.9 MB 27100 200
445
n
❚❚ DX (24×16) Image Area*
* Includes images taken with DX lenses when On is selected for Auto DX crop.
Image quality Image size File size 1No.
of images 1Buffer capacity 2
NEF (RAW), Lossless
compressed, 12-bit
—7.2 MB 2400 200
NEF (RAW), Lossless
compressed, 14-bit
—8.9 MB 1900 172
NEF (RAW),
Compressed, 12-bit
—6.6 MB 3200 200
NEF (RAW),
Compressed, 14-bit
—7.9 MB 2700 196
NEF (RAW),
Uncompressed,
12-bit
—12.0 MB 2400 133
NEF (RAW),
Uncompressed,
14-bit
—15.3 MB 1900 114
TIFF (RGB)
Large 21.5 MB 1400 61
Medium 12.6 MB 2300 68
Small 6.2 MB 4700 83
JPEG fine 3
Large 3.7 MB 5800 200
Medium 2.8 MB 8800 200
Small 1.9 MB 13500 200
JPEG normal 3
Large 2.3 MB 11100 200
Medium 1.6 MB 16200 200
Small 1.1 MB 24400 200
JPEG basic 3
Large 1.2 MB 20300 200
Medium 0.9 MB 28700 200
Small 0.7 MB 40700 200
446
n
1 All figures are approximate.
File size varies with scene recorded.
2 Maximum number of exposures that can be stored in memory buffer at ISO 100.
Drops if Optimal quality is selected for JPEG compression or auto distortion
control is on.
3 Figures assume JPEG compression is set to Size priority.
Selecting Optimal
quality increases the file size of JPEG images; number of images and buffer
capacity drop accordingly.
Ad3—Max. Continuous Release (0319)
The maximum number of photographs that can be taken in a single
burst can be set to any amount between 1 and 200.
447
n
Battery Life
The number of shots that can be taken with a fully-charged
EN-EL18 battery (2,000 mAh) varies with the condition of the
battery, temperature, and how the camera is used. Sample figures
are given below.
•CIPA standard: Approximately 2600 shots. Measured at 23 °C/
73.4 °F (±2 °C/3.6 °F) with an AF-S NIKKOR 24–70mm f/2.8G ED
lens under the following test conditions: lens cycled from infinity
to minimum range and one photograph taken at default settings
once every 30 s. Live view not used.
•Nikon standard: Approximately 5500 shots. Measured at 20 °C/68 °F
with an AF-S VR 70–200mm f/2.8G ED lens under the following
test conditions: vibration reduction off, image quality set to JPEG
normal, image size set to L (large), shutter speed 1/250 s, shutter-
release button pressed halfway for three seconds and focus
cycled from infinity to minimum range three times; six shots are
then taken in succession and monitor turned on for five seconds
and then turned off; cycle repeated once standby timer has
expired.
448
n
The following can reduce battery life:
•Using the monitor
• Keeping the shutter-release button pressed halfway
• Repeated autofocus operations
• Taking NEF (RAW) or TIFF (RGB) photographs
• Slow shutter speeds
• Connecting to Ethernet or wireless networks
• Using the optional GP-1 GPS unit
• Using VR (vibration reduction) mode with VR lenses
To ensure that you get the most from rechargeable Nikon EN-EL18
batteries:
• Keep the battery contacts clean.
Soiled contacts can reduce
battery performance.
• Use batteries immediately after charging.
Batteries will lose their
charge if left unused.
• Check the condition of the battery regularly using the Battery
info option in the setup menu (0351). If j is displayed for
Calibration, calibrate the battery using the MH-26 battery
charger (if the battery has not been used for more than six
months, recharge the battery when calibration is complete).
449
n
Index
Symbols
e (Programmed auto)........................ 126
f (Shutter-priority auto) ................... 127
g (Aperture-priority auto)................ 128
h (Manual).............................................. 129
S................................................................. 111
CL............................................. 111, 112, 318
CH............................................ 111, 112, 318
J............................................................... 111
E (Self-timer)............................... 111, 114
MUP ................................................... 111, 116
K (Single-point AF) ........................... 100
I (Dynamic-area AF)........................ 100
H (Auto-area AF) ................................ 101
! (Face-priority AF) .............................. 53
5 (Wide-area AF) ................................... 53
6 (Normal-area AF)............................... 53
& (Subject-tracking AF) .................... 53
L (Matrix) .............................................. 123
M (Center-weighted) ................ 123, 315
N (Spot).................................................. 123
R (Info) button................................ 13, 16
a (Live view).................................... 49, 63
Q (Help)............................................... 19, 22
t (Memory buffer).... 43, 113, 319, 444
D switch.......................................... 10, 322
I (Focus indicator)............. 43, 105, 109
L (Preset manual) .................. 154, 163
Numerics
1.2× (30 × 20)........................................... 86
12-bit .......................................................... 92
14-bit .......................................................... 92
3D color matrix metering III ............ 123
3D-tracking .................................. 100, 101
5 : 4 (30 × 24)............................................ 86
A
AC adapter.................................... 391, 396
Accessories ............................................ 391
Accessory shoe.............................. 17, 191
Active D-Lighting.............. 149, 184, 332
Add items (My Menu)......................... 381
ADL bracketing........................... 149, 325
Adobe RGB............................................. 299
AE & flash (Auto bracketing set) .... 139,
325
AE only (Auto bracketing set) 139, 325
AF...................... 52–54, 97–107, 307–312
AF activation.......................................... 309
AF area brackets.............................. 11, 38
AF fine-tune........................................... 359
AF-area mode................................. 53, 100
AF-C ................................................... 97, 307
AF-F............................................................. 52
B button .......................... 99, 309, 311
B button for vertical shooting... 99,
312
AF-S............................................. 52, 97, 308
After delete............................................ 290
Ambient brightness sensor.. 6, 57, 345
Angle of view ....................... 85, 389–390
Aperture.............................. 128–129, 133
Aperture Lock.............................. 133, 334
Aperture-priority auto ....................... 128
Aspect ratio..................................... 85, 366
Attaching the lens ................................. 28
Audio.............................. 65, 261, 291, 292
Audio output............................... 261, 436
Auto (White balance) ......................... 153
Auto bracketing ................ 139, 325, 326
Auto bracketing (Mode M)............... 326
Auto distortion control...................... 301
Auto DX crop .................................... 85, 88
Auto FP high-speed sync. ....... 193, 323
Auto image rotation ........................... 350
Auto ISO sensitivity control.............. 119
Auto-area AF................................ 101, 102
Autofocus ...... 52–54, 97–107, 307–312
Autofocus mode.............................. 52, 97
450
n
B
Backlight.......................................... 10, 322
Battery............. 23–27, 40, 351, 438, 440
Battery info............................................ 351
Beep ......................................................... 318
D button 141, 145, 149, 190, 212, 335
Black-and-white (Monochrome).... 367
Body cap.......................................... 28, 394
Border...................................................... 274
Bracketing........................... 139, 325, 326
Bracketing order.................................. 326
Bulb .......................................................... 131
Burst...................................... 112, 319, 329
Button backlights......................... 10, 322
C
Calibration ............................................. 440
Camera Control Pro 2................ 265, 393
Capture NX 2............... 91, 182, 346, 393
Center-weighted metering..... 123, 315
CF card ...................................... 33, 95, 443
CF card slot............................................... 95
Charging the battery .................... 23–24
Choose color temp. (White balance).....
154, 160
Choose image area .................. 71, 86, 88
Choose start/end point........................ 79
Clean image sensor ............................ 399
Clock ................................................. 31, 348
Clock battery.................................. 32, 406
Cloudy (White balance) .................... 154
CLS............................................................ 192
Color balance........................................ 368
Color space ............................................ 299
Color temperature .. 153, 154, 155, 160
CompactFlash......................... 33, 95, 442
Compatible lenses .............................. 385
Compressed (Type)................................ 92
Computer............................................... 263
Connector for external microphone . 3
Continuous high speed.. 111, 112, 318
Continuous low speed ... 111, 112, 319
Continuous release mode................ 111
Continuous-servo autofocus.... 97, 307
Control panel......................................... 7–9
Copy image(s) ....................................... 286
Copyright information....................... 353
CPU contacts ......................................... 387
CPU lens ................................. 29, 385, 387
Creative Lighting System........ 191, 192
Crop ............................................................ 74
Cropping (PictBridge [Setup] menu) ....
274
Custom Settings................................... 303
Custom settings bank ........................ 305
Customize command dials............... 336
Cyanotype (Monochrome) ............... 367
D
Date and time................................. 31, 348
Date format..................................... 32, 348
Daylight saving time.................... 31, 348
DCF.................................................. 299, 439
Default settings .......................... 207, 412
Delete................................................ 47, 251
Delete all images........................ 251, 253
Delete current image................... 47, 251
Depth of field .............................. 125, 128
Destination (Movie settings).............. 75
Digital Print Order Format (DPOF) 275,
277, 439
Diopter.............................................. 38, 392
Direct sunlight (White balance)...... 153
Distortion control ................................ 377
D-Lighting .............................................. 364
DPOF...................................... 275, 277, 439
DPOF print order.................................. 277
DX (24 × 16) 1.5 ×..................... 86, 88, 89
DX format.................................... 85, 86, 87
DX-based movie format....................... 71
Dynamic-area AF........................ 100, 102
E
Easy exposure compensation.......... 314
Edit movie.......................................... 79, 83
Electronic rangefinder ....................... 109
Ethernet......................................... 269, 391
EV steps for exposure cntrl............... 313
451
n
Exif................................................... 299, 439
Exp./flash comp. step value............. 313
Exposure..................... 123, 125, 135, 137
Exposure bracketing ....... 139, 325, 326
Exposure comp. for flash .................. 325
Exposure compensation.......... 137, 314
Exposure delay mode ........................ 319
Exposure differential.......................... 188
Exposure indicator.............................. 130
Exposure lock ....................................... 135
Exposure meters........................... 45, 233
Exposure mode.................................... 125
Exposure program .............................. 418
Extended menu banks ...................... 295
External microphone........... 69, 75, 395
F
Face-priority AF ...................................... 53
File information ................................... 239
File naming............................................ 298
File number sequence....................... 320
Filter effects........................ 176, 177, 367
Fine-tune optimal exposure............ 315
Firmware version................................. 360
Flash.................... 191, 192, 199, 202, 204
Flash (White balance) ........................ 153
Flash bracketing ............... 139, 325, 326
Flash compensation........................... 202
Flash control.......................................... 198
Flash mode................................... 199, 200
Flash only (Auto bracketing set) ... 140,
325, 326
Flash range ............................................ 192
Flash shutter speed ............................ 324
Flash sync speed.................................. 323
Flash sync terminal............................. 191
Flash-ready indicator 12, 195, 205, 434
Flexible program ................................. 126
Flicker reduction.................................. 348
Fluorescent (White balance) ........... 153
Fn button ...................... 89, 205, 328, 340
Fn button (vertical).............................. 334
f-number ....................................... 128, 388
Focal length........................ 228, 389–390
Focal plane mark.................................. 109
Focus ........ 52–54, 59, 97–109, 307–312
Focus indicator .................... 43, 105, 109
Focus lock............................................... 105
Focus mode ............................. 52, 97, 108
Focus mode switch ...................... 29, 108
Focus point .................. 53, 100, 103, 311
Focus point illumination ................... 310
Focus point wrap-around................. 310
Focus tracking................................ 99, 309
Focus tracking with lock-on............. 309
Focusing screen.................................... 431
Focus-mode selector............ 52, 97, 108
Format .............................................. 36, 345
Format memory card.......................... 345
Frame interval (Slide show).............. 291
Frame rate ................................................ 74
Frame size/frame rate........................... 74
Front-curtain sync ............................... 199
Full-frame playback............................. 235
Full-time servo autofocus................... 52
FV lock............................................ 204, 329
FX (36 × 24) 1.0 × ................................... 86
FX format ........................................... 85, 86
FX-based movie format....................... 71
G
GPS......................................... 231, 233, 245
GPS data.................................................. 245
GPS unit................................................... 231
H
H.264 ........................................................ 436
HDMI .............................................. 280, 439
HDMI mini-pin connector...................... 3
HDR (high dynamic range)............... 186
Headphones ............................................ 69
Help ..................................................... 19, 22
Hi................................................................ 118
Hide image............................................. 284
High definition............................ 280, 439
High Dynamic Range (HDR)............. 186
High ISO NR ........................................... 302
Highlights............................................... 240
452
n
Histogram ........................... 241, 242, 327
I
Image area.................... 29, 71, 85, 88, 93
Image comment.................................. 352
Image Dust Off ref photo ................. 346
Image overlay....................................... 369
Image quality........................................... 90
Image review ............................... 237, 289
Image size ................................................. 93
Incandescent (White balance)........ 153
Index marking ............ 67, 340, 341, 342
Index print ............................................. 275
In-focus indicator ................ 43, 105, 109
Information .................................. 238, 285
Information display ............ 13, 321, 322
Interval timer shooting ..................... 216
IPTC........................................................... 354
ISO sensitivity ....................... 75, 117, 119
ISO sensitivity range (Movie settings) ..
75
ISO sensitivity step value.................. 313
i-TTL................................................. 193, 198
J
JPEG.......................................... 90, 298, 372
JPEG basic ................................................. 90
JPEG compression.................................. 92
JPEG fine.................................................... 90
JPEG normal............................................. 90
L
L (large)................................................ 72, 93
LAN........................................................... 391
Landscape (Set Picture Control) .... 173
Language ........................................ 30, 349
LCD .................................................... 10, 322
LCD illumination .................................. 322
Lens ......................... 28–29, 228, 359, 385
Lens cap..................................................... 28
Lens focus ring ....................... 28, 59, 108
Lens mount................................. 4, 29, 109
Lens mounting index............................ 28
Live view............................................ 49–61
Live view photography ................ 49–61
Live view selector............................ 49, 63
Lo............................................................... 118
Lock mirror up for cleaning.............. 402
Long exposure NR ............................... 302
Lossless compressed (Type)............... 92
M
M (Manual focus) ........................... 59, 108
M (medium) ....................................... 72, 93
Manage Picture Control..................... 179
Manual (Exposure mode).................. 129
Manual focus .................................. 59, 108
Matrix ....................................................... 123
Max. continuous release.................... 319
Maximum aperture .......... 109, 228, 388
Maximum sensitivity........................... 120
Memory buffer..................... 43, 113, 319
Memory card .......... 33, 36, 95, 345, 442
Memory card capacity ....................... 444
Metering.................................................. 123
Microphone .......... 3, 6, 69, 75, 255, 395
Microphone (Movie settings) ............ 75
Minimum aperture....................... 29, 125
Minimum shutter speed.................... 120
Mired ........................................................ 158
Mirror.............................................. 116, 402
Mirror up mode .......................... 111, 116
Modeling flash............................ 125, 325
Monitor................... 49, 57, 235, 317, 345
Monitor brightness ...................... 57, 345
Monitor hue............................................. 56
Monitor off delay ................................. 317
Monochrome............................... 173, 367
Mounting index........................... 4, 28, 29
Movie live view.............................. 63, 340
Movie quality (Movie settings).......... 74
Movie settings......................................... 74
Movie-record button................... 65, 339
Multi selector.................................. 20, 328
Multi selector (vertical) ...................... 338
Multiple exposure................................ 210
Multi-selector center button ........... 327
My Menu ....................................... 330, 380
453
n
N
NEF (RAW)................ 90, 91, 92, 298, 372
NEF (RAW) bit depth ............................. 92
NEF (RAW) processing....................... 372
NEF (RAW) recording ............................ 92
Neutral (Set Picture Control) ........... 173
Nikon Transfer 2................................... 263
No. of copies (PictBridge [Setup] menu)
273
Non-CPU lens .................... 228, 385, 388
Non-CPU lens data..................... 228, 229
Normal-area AF....................................... 53
Number of focus points .................... 311
O
Optimal quality (JPEG compression) 92
Overview data ...................................... 246
P
Page size................................................. 273
Peripheral connector..................... 3, 391
Perspective control............................. 378
Photo information ..................... 238, 285
PictBridge...................................... 271, 439
Picture Controls ................................... 173
Pitching.......................................... 331, 358
Playback .......................... 46, 77, 235, 280
Playback display options.................. 285
Playback folder..................................... 284
Playback information................ 238, 285
Playback menu..................................... 283
Playback zoom............................ 247, 339
Portrait (Set Picture Control)........... 173
Power aperture ........................... 340, 341
Power connector........................ 391, 396
Predictive focus tracking ..................... 99
Preset manual (White balance)..... 154,
163
Press the shutter-release button
halfway..................................................... 44
Primary slot selection ........................... 95
Print (DPOF)........................................... 275
Print options (PictBridge [Setup] menu)
273
Print select.............................................. 275
Printing.................................................... 271
Programmed auto ............................... 126
Protecting photographs.................... 249
Pv button............. 67, 125, 325, 333, 341
Q
Quiet (Live view photography)......... 60
R
Rank items (My Menu) ....................... 383
Rear control panel .................................... 9
Rear-curtain sync ................................. 199
Recent settings..................................... 380
Rechargeable Li-ion battery 1, 23, 438,
440
Red-eye correction.............................. 365
Red-eye reduction............................... 199
Release button to use dial ................ 337
Release mode........................................ 111
Remote cord....................... 131, 394, 395
Remove items (My Menu)................. 382
Removing the lens from the camera 29
Reset...................................... 207, 295, 305
Resize ....................................................... 374
Restoring default settings ..... 207, 295,
305, 412
Retouch menu ...................................... 361
Reverse indicators ............................... 338
RGB........................................... 90, 241, 299
RGB Histogram ..................................... 241
Rolling............................................ 331, 358
Rotate tall ............................................... 290
S
S (small)............................................... 72, 93
Save selected frame....................... 79, 83
Save/load settings ............................... 356
Screen tips.............................................. 321
Secondary slot function ...................... 95
Self-timer ............................. 111, 114, 317
Sensitivity ..................................... 117, 119
Set Picture Control .............................. 173
Setup menu ........................................... 344
Shade (White balance)....................... 154
454
n
Shooting data....................................... 243
Shooting menu.................................... 293
Shooting menu bank......................... 294
Shutter speed .................... 127, 129, 133
Shutter speed lock.............................. 133
Shutter-priority auto.......................... 127
Shutter-release button 43, 44, 105, 135,
343
Shutter-release button AE-L............ 316
Side-by-side comparison.................. 378
Silent (Live view photography) ......... 60
Single frame .......................................... 111
Single-point AF ........................... 100, 102
Single-servo autofocus ....... 52, 97, 308
Size .................................... 72, 93, 366, 374
Size priority (JPEG compression)...... 92
Skylight ................................................... 367
Slide show.............................................. 291
Slot.............................................. 33, 95, 236
Slot empty release lock..................... 338
Slot selection ........................................ 236
Slow sync................................................ 199
Smoothing............................................. 188
Speaker .......................................... 260, 261
Speedlights......................... 191, 192, 194
Spot.......................................................... 123
sRGB ......................................................... 299
Standard (Set Picture Control)........ 173
Standard i-TTL flash for digital SLR 193,
198
Standby timer....................... 45, 233, 316
Start printing ............................... 274, 277
Storage folder....................................... 296
Store points by orientation.............. 312
Straighten .............................................. 376
Sub-selector .... 104, 105, 135, 333, 342
T
Television................................................ 280
Ten-pin remote terminal.... 3, 231, 394,
395
Thumbnail..................................... 235, 327
TIFF (RGB).................................................. 90
Time .................................................. 31, 348
Time stamp ............................................ 274
Time zone ........................................ 31, 348
Time zone and date ..................... 31, 348
Time-lapse photography .................. 223
Timer............................................... 114, 216
Toning (Set Picture Control)... 176, 178
Top control panel................................. 7–8
Trim ........................................................... 366
Two-button reset ................................. 207
Type D lens............................................. 387
Type G lens............................................. 387
U
Uncompressed (Type).......................... 92
USB.................................................. 267, 272
USB cable.................................. 1, 267, 272
Use GPS to set camera clock............ 233
UTC........................................... 31, 232, 245
V
Viewfinder ................................ 11, 38, 431
Viewfinder eyepiece .................... 39, 114
Viewfinder focus..................... 38, 39, 392
Viewfinder grid display...................... 321
ViewNX 2............. 91, 263, 299, 350, 352
Vignette control.................................... 300
Virtual horizon .............. 58, 70, 331, 358
Vivid (Set Picture Control)................. 173
Voice memo................................. 255–261
Voice memo button............................ 256
Voice memo overwrite....................... 256
W
Warm filter.............................................. 367
WB ................................................... 145, 153
WB bracketing (Auto bracketing set)....
145, 325
White balance ............................. 145, 153
White balance bracketing....... 145, 325
Wide-area AF ........................................... 53
Wireless network........................ 269, 391
Wireless transmitter.................. 269, 391
WT-4................................................ 269, 391
WT-5................................................ 269, 391
455
n
X
XQD card .................................. 33, 95, 442
XQD card slot........................................... 95
a
456
DIGITAL CAMERA
En
User's Manual
Printed in Europe
SB3A04(11)
6MB13011-04
No reproduction in any form of this manual, in whole or in part
(except for brief quotation in critical articles or reviews), may be
made without written authorization from NIKON CORPORATION.
AMA14637
En

Navigation menu