Ningbo Chima wh CM-CMT Receiver of Electric Winch Wireless Controller User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4192089
Application ID	y+jnSLXkTnDY8xahN4O2SA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.61kB (57653 bits)
Date Submitted	2019-03-06 00:00:00
Date Available	2019-03-06 00:00:00
Creation Date	2019-01-14 11:59:22
Producing Software	pdfFactory Pro 5.25 (Windows 7 Ultimate x64 Chinese (Simplified))
Document Lastmod	2019-03-06 10:46:25
Document Title	Electric winch wireless controller instructions_EN（CM-CMT）.doc
Document Creator	pdfFactory Pro www.pdffactory.com
Document Author:	cwl

Electric winch wireless controller instructions
A, Features Overview
The wireless receiver operates at 315 MHz and has a control range of more than 25 meters. It is used
for wireless control of electric winch
B, The wireless remote control parameters
1, Working voltage: DC7-18V.
2, The working current: 7mA ± 3mA
3, Receiving frequency : 315MHz
C, Installation and function
1,Disconnect Power to the winch
2,Confirm that the plug is the correct type for this winch and plug it in
3.Select an area for the receiver on the vehicle close enough to the winch to allow cable
connection
4.Investigate the chosen area to make sure no components will be damaged by installation.
5.Permanently (optional) mount the remote control receiver to the vehicle using appropriate
hardware (not included).
6.Preare the winch for operation as explained in its manual
7.Reconnect winch’s power
8.Release the clutch handle and pull out about 10 feet of wire rope Leave the wire rope
laying on the ground and stay clear of the wire rope and hook
9.Reengage the clutch handle
10.Watch the spool and wire rope and briefly, press the out button on the remote control to
verify that the cable feeds out
WARNING! If the cable does not feed out ,check and correct the winch’s wiring. Retest
after correction.
11.Watch the spool and wire rope and briefly press the in button on the remote control to
verify that the cable retracts
WARNING! If the cable does not feed out ,check and correct the winch’s wiring .Retest
BOTH functions after correction.
12.If the remote operates the winch properly, it is ready for use.
13.After use, disconnect control box from winch to prevent accidental operation
D,WARNING!
To prevent serious injury
1. Disconnect control box from winch before service and after every use.
WINCH CAN OPERATE SUDDENLY AT ANY TIME WHILE CONNECTED.
2. Stand clear of winch, fairlead, and wire rope while connected. Keep bystanders away.
3. Only operate controls when winch and entire wire rope is within view.
4. Use with vehicle mounted recovery winches only. Do not use for any other application.
5. Confirm control box mounting location has no wire or components that can be damaged
drilling.
6. Read winch manual before use.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : cwl
Create Date                     : 2019:01:14 11:59:22+08:00
Modify Date                     : 2019:03:06 10:46:25-08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : cwl
Title                           : Electric winch wireless controller instructions_EN（CM-CMT）.doc
Creator Tool                    : pdfFactory Pro www.pdffactory.com
Metadata Date                   : 2019:03:06 10:46:25-08:00
Producer                        : pdfFactory Pro 5.25 (Windows 7 Ultimate x64 Chinese (Simplified))
Document ID                     : uuid:7418cd3e-3839-45cd-bd5c-4ba5c92e9558
Instance ID                     : uuid:fb1d33aa-aae3-4943-a953-d96e302a940f
Page Layout                     : SinglePage
Page Count                      : 2

EXIF Metadata provided by EXIF.tools