Ningbo Fancier Photographic Equipment WI710 IQ Motion Gimbal User Manual 1
Ningbo Fancier Photographic Equipment Co.,Ltd. IQ Motion Gimbal 1
Contents
- 1. Users Manual
- 2. user manual
user manual
Charging the Batteries For the first use of Wi—710, please use the dedicated charging device contained in the package to fuly charge and activate the batteries to ensure the normal use of the product Charger & Battery Description Charger Specifications Name: 18650%4 Li—ion battery charger Model: HZO4L—2000 Input: SV———2000mA Output: 4.2V————400mA*4 * Shines solid RED light when charging * Shines GREEN light when fully charged Battery Specifications Name: 18650 Li—ion battery Model: 18650 Capacity: 2200mAh Voltage: 3.7V Notice: 1. Please read the disclaimer and warning herein as well as the description on the battery label carefull before using the batteries. on en 2. TheHZG4L—2000 chargarisforchargngWoteng‘s (O] T (4! 18650 Li—ion Battery only. Do not charge batteries of other models or brands, otherwise it may lead to accident | Pleaso use and charge batterias provided or approved | byWelfeng only Welfeng wilnot take anyresponsipity | for explosion, fire and/or accidents caused by non— | Weiteng battories: L ® Charging the Batterios Charging Procedure 1.Insert the batteries into the charger in the right direction (positve/negative end) accordingly. 2. Gonnect the charger to the adapter via the Micro USB cable. 3. Plug the adapter into the power outlat to start charging Micro USB Cable SV Adapter PowerOutict 1. Due to different chargers, the charging may fall when the poweris under charged (like when the current of adapter is below 1000mA); Adapter with higher current capacity is recommended; 2. The USB port along side the stablizer does not support charging to batteries 1, Please use qualfed standard SV/22000mA adapter for battery charging; Charging time depends on the maximum output current of the adapter 2. The stablizer comes standard with high—discharge—rate dedicated batteries Please use and charge batteries provided or approved by Weifeng only. 3. Pleaso make sure allfour batteries are fuly charged. Either under charged battery can lead to the fallure of the stabilizer. Installation Battery Installation Instalation Installing Camera Open the battery compartment by pressing the button at the bottom and insert the four 18650 batteries in the right direction (positive/negative end), then close the battery compartment. Please use and charge batteries provided or approved by Weifeng only, in case of accidents. Tripod Get the tripod ready and tighten it to the 1/4"—3/8" threaded hole at the bottom of the stabilizer, then unfold the tripod on a flat surface (— \ 1. Loosen the mounting plate thumb screw, press and hold the safety lock while siding out the quickrelease plate 2.Instal the camera to the quickrelease plate as shown in the igure, then ighten the 1/4" screw at the bottom 3. Side in the quickrelease plate installed with the camera, then tighten the thumb serew to finish the nstalation of the auick release plate. 4.Loosen the serew onlens support and adjust the support to keep the lens frmand stabiized then tighten the screw. (Lens support needs to be installed when the lens is longer and heavier) Do not power on the stablizer before finishing the camera installation; Please hold the camera with one hand when powering on the stabilzer in case of maltunctioned rotation Installation Connecting Camera Control Cable r— in the case of Canon camera(see more on Page 27——Camera Setting Screen), connect the control cable to the port on the camera platform with the MiniUSB end, and then the other end to the left—sice _ portontthecamora Rsomake sarethastastzerispomeredottorn stancty made uen comactng the cameracontrolcabia in case of mattnctonedrotation Weifeng Camera Control Gable Description Camera ue Ganon Sony Panasonic Gamera . | GanonE08C@m@®@S | Sony camerawi . mode! withNMiniUSS ntertace Sony camera wih ensioraans Camemtontel Min—oo1 mucri—oo1 ona—o01 Cabemode! GameraGontral, MiniUSB (10 pin) o .| MiniUS8(fopin)to Gableinterface Mini USB(S pin) murnuss MiniUS8 (opin) to CTA USB Photo T 7 7 Video 7 Ke 7 Autorocus 7 7 7 Currently Supported camera models: . Canon:502, 503, 800,60,602; Sony: RX1OOMS,A6500A75 A7S2,A7R,A7R2,A7RG A7M3,A0, "Sorme eameras may faito take iesures ue to stow or aing foousing n complex on vrorments such as wouk ioh manua focus mode nracormmendeg when vang camera conta functon "When usng ho camara contra tuncton is recommandea to in ollthe camore s automat vew (BONY) o mage reeagnton (Ganon) and atna hinctiona to resuce w ayatom dony fHlfore uang the camore contra uncton plaase aslet m correct camera made n APP orth stastzer "Ta enaure thas e tabizer corrcty denihs n camora power on the sinizetrs aterthe Gamera Contvl Cabieiscomactes,than power on the camom "ne tme intorvatot star ancstap recorcing contrted by the gmoa!is 1 second © Balance Adjustment Please make sure the camera is properly mounted and balanced, otherwise the stabilizer may fail to start or operate normally. Level Adjustment on Tilt Axis Loosen the thumb screw on the quickrelease plate so that itcanside forward or backward _1 Hold the horizontalarm on the titaxiswithone handandadjust the position of the camera to find a level balance where the cameracanstaystiland amost level with is lens facing front, completethisstep by tightering up thecameramountingthumb scrow. Balance Adjustment The balance status of the stabiizer will greatly affect the run time.!f the camera blocks the thumb serew, the thumb screw can be pulled out and then rotate Balance Adjustment on Tilt Axis — _] Loosen the thumb screw ; Adjustthetitaxis untithe camera can stay still with the lens facing up (.e. thecamerastays stiland verticalto the ground), complete thisstepby tightening upthumbscrew. Loosen the thumb screw on the rollaxis. Adjust the rollaxis untilthe camera can stay stil while keeping the horizontal arm level. Complete this step by tightening up thumb screw. Balance Adjustment on Pan Axis Balance Adjustment Ifthe camera installed is too light that it‘s impossible to achieve balanced adjustmont, you can install the heighten plate on the mounting plate to finish balance installation Loosen the thumb serew on the pan axis. Adjust the pan axis unti the camera can stay stil while keaping the vertical arm level when turned to the right/eftside. Complete baiance adjustment by tightening up allthumb scrows Control Panel introduction Control Panel Description 1Status Incicator Light 2 Joystick 3 Mode Button 4 CameraControl Button 5 Power Button 1.Status Indicator Light(Light 1, Light 2, Light 3) When mode switches, Light 1 fashesindicating Pan Following Mode; Light 2 flashes indicating Following Mode; Light 3 fashes indicating Locking Mode: 2. Joystick Four—way direction control of the camera/lons 3Mode Button «The stabiizer enters PanFollowing Mode (PF) by default each tme when powered on Switch into Following Mode (F) by single pressing on Mode Button. Single press Mode Button again to enter Locking Mode (L). Single press Mode Button under Locking Mode willreturn to the Pan Following Mode «Double press the Made Button can make the stabilizer Titt Axis Motor and Roll Axis Motor back to the starting position: & Long press to quick enter the Locking Mode, release torestore the previous status © Control Panel ntroduction 4.Camera ControlButton sHalway press to realize auto foous «Fuly press to start or end video recording «Long pross to take pictures 5 Power Button «Long press for 3 seconds to power on/off «Single press to view the battery level (one indicator light on means 80%—60% power two indicatorights on means 60% —90%power,three incicator ights on means 90%—100% power) When one indicator ight flashes quickly means less than 0% power. «Double press to enter or exit standby mode « Triple press to enter the Full—speed Following Mode «Quadruple press can switch the left/right control direction of the Joystick. Combination use of buttons Press and hold the Mode button with one hand, and double press the Power Button with another hand when the lens is facing up, push the joystick left /night to enter the incaption mode.(360°rotation on Rollaxis) Please make sure the camera is well balanced, otherwise it can not move at a uniform speed Control Panel introduction Weifeng — Panasonic Camera Control Function Description (Need to switch to video mode) Please refer to the Camera Setting Screen in APP Operation on page 27 to choose the right option for your camera. 1.Shutter release: Hallway press 4 ‘Camera Control Button® to realize auto focus and take single shots by long press 2. Video recording: Fully press 4 "Camera Control Button® to start or end video recording Weifeng — Sony Camera Control Function Description (No need to switch to video mode) Please refer to the Camera Satting Screen in APP Operation on page 27 to choose theright option for your camera. 1.Shutterreloase: Haltway press 4 "Camera Control Button® to realze auto foous and take single shots by long press 2. Video recording: Fully press 4 "Camera Control Button® to start or end video recording 1. For Sony and Panasonic mirroriess camera with EVF, Real—time Preview is not needed. 2. When mounting a Sony camera to the stablizer, make sure to power on the stablizer before the camera, otherwise the stabilzer may fall to control the camera 3. When powering on the stabiizer, please hold the camera with one hand in case of malfunctioned rotation: 4. When powering on, avoid shaking of the stabilizer which may lead to start—up talure 5. For a Canon camera, the button works the same way as Sony‘s MODE SWITCH Introducing Gimbal Control Modes PowerON ——» Fallowing ——¥ Mode p Soglerass Sogs om an _ #60e80T00% poliowing "C—=T00! / Locking Mode Mode Singe ress woogeutron Pan Following Mode The camera pans left/right following the movement of the stablizor whie the tit and rolaxesare locked. Pushthe joystickupdownalowsmancal controlofthe it axs. Push the Joystildeft/ightalows manual contralofthe panaxis. The tit exscanbemanualyposttoned by defautinthismode. Following Mode The camerapansandtits following the movement of the stabilzer whie the rolaxisislocked Pushthe Joystckup/downandlatt nigntalowsmanualcontral ofthetitaxsandpanax‘s Both axes can not be manually positioned in this mode Locking Mode Trismodelocksmovement ofalthree axestokeap the camerafixedonashooting direction. Push the oystick up/down and left/right allows manual control of the tit ax‘s and pan axs. Ti and Pan axes can be manualy positioned in this mode
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 6 Create Date : 2018:12:28 16:16:30+08:00 Modify Date : 2018:12:28 16:16:30+08:00 Producer : Corel PDF Engine Version 16.1.0.843 Author : Administrator Creator : CorelDRAW X6 Title : 未命名 -1EXIF Metadata provided by EXIF.tools