Nokia Bell G240WB GPON ONU User Manual 7368 ISAM ONT G 240W B Product Guide

Download:
Mirror Download [FCC.gov]
Document ID	2574515
Application ID	j+u0lXKSOB17vcvRmqxqVg==
Document Description	6. User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	205.31kB (2566389 bits)
Date Submitted	2015-04-02 00:00:00
Date Available	2015-07-31 00:00:00
Creation Date	2015-01-08 12:09:42
Producing Software	Microsoft® Word 2010
Document Lastmod	2015-03-05 16:06:16
Document Title	7368 ISAM ONT G-240W-B Product Guide
Document Creator	Microsoft® Word 2010
Document Author:	Alcatel-Lucent

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368
INTELLIGENT SERVICES ACCESS MANAGER ONT
G-240W-B PRODUCT GUIDE
Alcatel-Lucent Proprietary
This document contains proprietary information of Alcatel-Lucent and is not to be disclosed
or used except in accordance with applicable agreements.
Copyright 2014 © Alcatel-Lucent. All rights reserved.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is
subject to change without notice.
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All
other trademarks are the property of their respective owners.
Copyright 2014 Alcatel-Lucent.
All rights reserved.
Disclaimers
Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design
engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous
environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life-support machines, or weapons
systems, in which the failure of products could lead directly to death, personal injury, or severe physical
or environmental damage. The customer hereby agrees that the use, sale, license or other distribution
of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at
the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from
any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the
use, sale, license or other distribution of the products in such applications.
This document may contain information regarding the use and installation of non-Alcatel-Lucent
products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent
tries to ensure that this information accurately reflects information provided by the supplier, please refer
to the materials provided with any non-Alcatel-Lucent product and contact the supplier for
confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete
information provided about non-Alcatel-Lucent products.
However, this does not constitute a representation or warranty. The warranties provided for
Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by
Alcatel-Lucent and its customers.
This document was originally written in English. If there is any conflict or inconsistency between the
English version and any other version of a document, the English version shall prevail.
When printed by Alcatel-Lucent, this document is printed on recycled paper.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Preface
This preface provides general information about the documentation set for optical
network terminals (ONTs).
Scope
This documentation set provides information about safety, features and
functionality, ordering, hardware installation and maintenance, and software
installation procedures for the current release.
Audience
This documentation set is intended for planners, administrators, operators, and
maintenance personnel involved in installing, upgrading, or maintaining the ONTs.
Required knowledge
The reader must be familiar with general telecommunications principles.
Acronyms and initialisms
The expansions and optional descriptions of most acronyms and initialisms appear
in the glossary.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
iii
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Preface
Assistance and ordering phone numbers
Alcatel-Lucent provides global technical support through regional call centers.
Phone numbers for the regional call centers are available at the following URL:
http://www.alcatel-lucent.com/myaccess.
For ordering information, contact your Alcatel-Lucent sales representative.
Alcatel-Lucent quality processes
Alcatel-Lucent’s ONT manufacturing, testing, and inspecting practices are in
compliance with GR-1252-CORE and TL 9000 requirements. These requirements
are documented in the Operations Quality Plan 8BD-00023-4204-QRZZA, the
Alcatel North American Quality Manual 8BD-00001-0000-QRZZA, and the
Wireline Network Quality Manual 8AB-83179-0001-QRAAA.
The quality plans and practices adequately ensure that technical requirements and
customer end-point requirements are met. The customer or its representatives may
be allowed to perform on-site quality surveillance audits, as agreed upon during
contract negotiations.
Safety information
For safety information, see the appropriate safety guidelines chapter.
Documents
Documents are available using ALED or OLCS.
Procedure 1 To download a ZIP file package of the customer
documentation
iv
Navigate to http://www.alcatel-lucent.com/myaccess and enter your user name
and password. If you are a new user and require access to this service, please
contact your Alcatel-Lucent sales representative.
From the Technical Content for drop-down menu, choose the product.
Click on Downloads: Electronic Delivery.
Choose Documentation from the drop-down menu and click Next.
Select the image from the drop-down menu and click Next.
Follow the on-screen directions to download the file.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Preface
Procedure 2 To access individual documents
Individual PDFs of customer documents are also accessible through the Alcatel-Lucent
Customer Support website.
Navigate to http://www.alcatel-lucent.com/myaccess and enter your user name
and password. If you are a new user and require access to this service, please
contact your Alcatel-Lucent sales representative.
From the Technical Content for drop-down menu, choose the product.
Click on Manuals and Guides to display a list of customer documents by title and
part number. You can filter this list using the Release drop-down menu.
Click on the PDF to open or save the file.
Special information
The following are examples of how special information is presented in this
document.
Danger — Danger indicates that the described activity or situation
may result in serious personal injury or death; for example, high
voltage or electric shock hazards.
Danger indique que l'activitéou la situation décrite
peuvent entraî
ner des blessures corporelles graves ou mortelles;
par exemple, haute tension ou de risques d'électrocution.
Warning — Warning indicates that the described activity or situation
may, or will, cause equipment damage or serious performance
problems.
Warning indique que l'activitéou la situation décrite ne
peut, ou la volonté, des dommages matériels de cause ou de graves
problèmes de performance
Caution — Caution indicates that the described activity or situation
may, or will, cause service interruption.
Caution indique que l'activitéou la situation décrite
peut, ou la volonté, le service de la cause interruption.
Note — A note provides information that is, or may be, of special
interest.
Une note fournit des informations qui est, ou peut être,
d'un intérêt particulier.
Procedures with options or substeps
When there are options in a procedure, they are identified by letters. When there are
required substeps in a procedure, they are identified by roman numerals.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Preface
Procedure 3 Example of options in a procedure
At step 1, you can choose option a or b. At step 2, you must do what the step indicates.
This step offers two options. You must choose one of the following:
This is one option.
This is another option.
You must perform this step.
Procedure 4 Example of required substeps in a procedure
At step 1, you must perform a series of substeps within a step. At step 2, you must do
what the step indicates.
This step has a series of substeps that you must perform to complete the step. You
must perform the following substeps:
This is the first substep.
ii
This is the second substep.
iii
This is the third substep.
You must perform this step.
Multiple PDF document search
You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a
common term. Adobe Reader displays the results in a single display panel. The
results are grouped by PDF file, and you can expand the entry for each file.
Note — The PDF files in which you search must be in the same
folder.
Les fichiers PDF dans lequel vous recherchez doivent
être dans le même dossier
Procedure 5 To search multiple PDF files for a common term
vi
Open Adobe Acrobat Reader.
Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel
appears.
Enter the search criteria.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Preface
Click on the All PDF Documents In radio button.
Select the folder in which to search using the drop-down menu.
Click on the Search button.
Acrobat Reader displays the search results. You can expand the entries for each
document by clicking on the + symbol.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
vii
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
This chapter provides information about the mandatory regulations that govern the
installation and operation of the optical network terminals (ONTs).
Safety instructions
This section describes the safety instructions that are provided in the ONT customer
documentation and on the equipment.
Safety instruction boxes
The safety instruction boxes are provided in the ONT customer documentation.
Observe the instructions to meet safety requirements.
The following is an example of the Danger box.
Danger — Possibility of personal injury.
Possibilitéde blessures.
The Danger box indicates that the described activity or situation may pose a threat to
personal safety. It calls attention to a situation or procedure which, if not correctly
performed or adhered to, may result in death or serious physical harm.
Do not proceed beyond a Danger box until the indicated conditions are fully
understood and met.
The following is an example of the Warning box.
Warning 1 — Possibility of equipment damage.
Possibilitéde dommages matériels.
Warning 2 — Possibility of data loss.
Possibilitéde perte de données.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
The Warning box indicates that the described activity or situation may, or will, cause
equipment damage, loss of data, or serious performance problems. It identifies a
possible equipment-damaging situation or provides essential information to avoid
the degradation of system operations or data.
Do not proceed beyond a warning until the indicated conditions are fully understood
and met.
The following is an example of the Caution box.
Caution 1 — Possibility of service interruption.
Possibilitéd'interruption de service.
Caution 2 — Service interruption.
Interruption de service
The Caution box indicates that the described activity or situation may, or will, cause
service interruption.
Do not proceed beyond a caution until the indicated conditions are fully understood
and met.
The following is an example of the Note box.
Note — Information of special interest.
L'information d'intérêt spécial.
The Note box provides information that assists the personnel working with ONTs. It
does not provide safety-related instructions.
Safety-related labels
The ONT equipment is labeled with the specific safety instructions and compliance
information that is related to a variant of the ONT. Observe the instructions on the
safety labels.
Table 1 provides sample safety labels on the ONT equipment.
Table 1 Safety labels
Description
Label text
ESD warning
Caution: This assembly contains an electrostatic sensitive device.
Laser classification
Class 1 laser product
PSE marking
These power supplies are Japan PSE certified and compliant with
Japan VCCI emissions standards.
Figure 1 shows the PSE certification.
Alcatel-Lucent 7368 ISAM ONT
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
Figure 1 PSE certification
Warning
This is a Class B product based on the standard of the Voluntary Control Council for Interference
from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in
a domestic environment, it may cause radio interference. Install and use the equipment according
to the instruction manual.
19841
Safety standards compliance
This section describes the ONT compliance with the European safety standards.
EMC, EMI, and ESD compliance
The ONT equipment complies with the following EMC, EMI, and ESD
requirements:
• EN 300-386 V1.3.2 (2003-05): Electromagnetic Compatibility and Radio
•
•
•
•
•
•
•
•
•
•
•
•
•
Spectrum Matters (ERM): Telecommunications Network Equipment;
Electromagnetic Compatibility (EMC) requirements; Electrostatic Discharge
(ESD) requirements
EN 55022 (1998): Class B, Information Technology Equipment, Radio
Disturbance Characteristics, limits and methods of measurement
EN 55024 (1998): Information Technology Equipment, Immunity
Characteristics, limits and methods of measurement
European Council Directive 2004/108/EC
EN 300-386 V1.4.1: 2008
EN 55022:2006 Class B (ONTs)
EN EN 61000-3-2:2006
EN EN 61000-3-3:2008
IEC 61000-4-2:2001
IEC 61000-4-3:2006
IEC 61000-4-4:2004
IEC 61000-4-5:2005
IEC 61000-4-6:2003/A1:2004/A2:2006
IEC 61000-4-11:2004
Equipment safety standard compliance
The ONT equipment complies with the requirements of EN 60950-1, Safety of
Information Technology Equipment for use in a restricted location (per R-269).
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xi
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
Environmental standard compliance
The ONT equipment complies with the EN 300 019 European environmental
standards.
Laser product standard compliance
For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2
for laser products. If there is an exception to this compliance regulation, you can find
this information in the standards compliance section of the unit data sheet in this
Product Guide.
Resistibility requirements compliance
The ONT equipment complies with the requirements of ITU Recommendation K.21
for resistibility of telecommunication equipment installed in customer premises to
over voltage and overcurrents.
Acoustic noise emission standard compliance
The ONT equipment complies with EN 300 753 acoustic noise emission limit and
test methods.
Electrical safety guidelines
This section provides the electrical safety guidelines for the ONT equipment.
Note 1 — The ONTs comply with the U.S. National Electrical Code.
However, local electrical authorities have jurisdiction when there are
differences between the local and U.S. standards.
Les ONT sont conformes àla US National Electrical Code.
Cependant, les autorités locales électriques ont compétence quand il ya
des différences entre les normes locales et américaines.
Note 2 — The ONTs comply with BS EN 61140.
Les ONT sont conformes à la norme
BS EN 61140
Power supplies
The use of any non-Alcatel-Lucent approved power supplies or power adapters is not
supported or endorsed by Alcatel-Lucent. Such use will void any warranty or support
contract with Alcatel-Lucent. Such use greatly increases the danger of damage to
equipment or property.
Cabling
The following are the guidelines regarding cables used for the ONT equipment:
• All cables must be approved by the relevant national electrical code.
• The cables for outdoor installation of ONTs must be suitable for outdoor use.
• POTS wiring run outside the subscriber premises must comply with the
requirements of local electrical codes. In some markets, the maximum allowed
length of the outside run is 140 feet (43 m). If the outside run is longer, NEC
requires primary protection at both the exit and entry points for the wire.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
Protective earth
Earthing and bonding of the ONTs must comply with the requirements of local
electrical codes.
ESD safety guidelines
The ONT equipment is sensitive to ESD. Operations personnel must observe the
following ESD instructions when they handle the ONT equipment.
Caution — This equipment is ESD sensitive. Proper ESD protections
should be used when you enter the TELCO Access portion of the
ONT.
Cet équipement est sensible ESD. Protections relatives
aux décharges électrostatiques doivent être utilisés lorsque vous
entrez dans la partie d'accès TELCO de l'ONT
During installation and maintenance, service personnel must wear wrist straps to
prevent damage caused by ESD.
Laser safety guidelines
Observe the following instructions when you perform installation, operations, and
maintenance tasks on the ONT equipment.
Only qualified service personnel who are extremely familiar with laser radiation
hazards should install or remove the fiber optic cables and units in this system.
Danger — There may be invisible laser radiation at the fiber optic
cable when the cable is removed from the connector. Avoid direct
exposure to the laser beam.
Il peut y avoir un rayonnement laser invisible sur le
câble à fibre optique lorsque le câble est retiré du connecteur.
Éviter l'exposition directe au rayon laser.
Observe the following danger for laser hazard. Eyes can be damaged when they are
exposed to a laser beam. Take necessary precautions before you plug in the optical
modules.
Danger — Possibility of equipment damage. Risk of eye damage by
laser radiation.
Possibilitéde dommages matériels. Risque de lésions
oculaires par un rayonnement laser.
Laser classification
The ONT is classified as a Class 1 laser product based on its transmit optical output.
Laser warning labels
The following figures show the labels related to laser product, classification and
warning.
Figure 2 shows a laser product label.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
Figure 2 Laser product label
18455
Figure 3 shows a laser classification label. Laser classification labels may be
provided in other languages.
Figure 3 Laser classification label
CLASS 1 LASER PRODUCT
PRODUCTO LASER CLASE 1
CLASE 1 DEL LASER
LASER CLASSE 1
18992
Figure 4 shows a laser warning label and an explanatory label for laser products.
Labels and warning may be provided in other languages. The explanatory label
provides the following information:
• a warning that calls attention to the invisible laser radiation
• an instruction against staring into the beam or viewing directly with optical
instruments
• wavelength
• normal output power
• maximum output power
xiv
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
Figure 4 Laser warning labels
INVISIBLE LASER RADIATION
DO NOT STARE INTO BEAM
OR VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
Wavelength(s): xxxx nm
Normal output power: xx m W
Max output power: yyy m W
Laser Warning Label
Laser Warning Label
CLASS 1 LASER PRODUCT
RAYONNEMENT LASER CLASSE 1
RAYONNEMENT LASER INVISIBLE EVITER
TOUTE EXPOSITION AU FAISCEAU
NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE
CLASE 1 DEL LASER
RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL
RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO
INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE
WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM.
Laser Warning Label
18993
Transmit optical output
The maximum transmit optical output of an ONT is +5 dBm.
Normal laser operation
In normal operation, fiber cable laser radiation is always off until it receives signal
from the line terminal card.
Eyes can be damaged when they exposed to a laser beam. Operating personnel must
observe the instructions on the laser explanatory label before plugging in the optical
module.
Danger — Risk of eye damage by laser radiation.
Risque de lésions oculaires par un rayonnement laser.
Location class
Use cable supports and guides to protect the receptacles from strain.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xv
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelines
Environmental requirements
See the ONT technical specification documentation for more information about
temperature ranges.
During operation in the supported temperature range, condensation inside the ONT
caused by humidity is not an issue. To avoid condensation caused by rapid changes
in temperature and humidity, Alcatel-Lucent recommends:
• The door of the ONT not be opened until temperature inside and outside the
enclosure has stabilized.
• If the door of the ONT must be opened after a rapid change in temperature or
humidity, use a dry cloth to wipe down the metal interior to prevent the risk of
condensation.
• When high humidity is present, installation of a cover or tent over the ONT helps
prevent condensation when the door is opened.
xvi
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelines
This chapter provides information about the ETSI environmental China Restriction
of Hazardous Substances (CRoHS) regulations that govern the installation and
operation of the optical line termination (OLT) and optical network termination
(ONT) systems. This chapter also includes environmental operation parameters of
general interest.
Environmental labels
This section describes the environmental instructions that are provided with the
customer documentation, equipment, and location where the equipment resides.
Overview
CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold
and imported in the territory of the mainland of the People’s Republic of China. EIP
refers to products and their accessories manufactured by using electronic information
technology, including electronic communications products and such subcomponents
as batteries and cables.
Environmental related labels
Environmental labels are located on appropriate equipment. The following are
sample labels.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xvii
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelines
Products below Maximum Concentration Value (MCV) label
Figure 1 shows the label that indicates a product is below the maximum
concentration value, as defined by standard SJ/T11363-2006 (Requirements for
Concentration Limits for Certain Hazardous Substances in Electronic Information
Products). Products with this label are recyclable. The label may be found in this
documentation or on the product.
Figure 1 Products below MCV value label
18986
Products containing hazardous substances above Maximum Concentration
Value (MCV) label
Figure 2 shows the label that indicates a product is above the maximum
concentration value, as defined by standard SJ/T11363-2006 (Requirements for
Concentration Limits for Certain Hazardous Substances in Electronic Information
Products). The number contained inside the label indicates the
Environment-Friendly User Period (EFUP) value. The label may be found in this
documentation or on the product.
xviii
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelines
Figure 2 Products above MCV value label
18985
Together with major international telecommunications equipment companies,
Alcatel-Lucent has determined it is appropriate to use an EFUP of 50 years for
network infrastructure equipment and an EFUP of 20 years for handsets and
accessories. These values are based on manufacturers' extensive practical experience
of the design, manufacturing, maintenance, usage conditions, operating
environments, and physical condition of infrastructure and handsets after years of
service. The values reflect minimum values and refer to products operated according
to the intended use conditions. See “Hazardous Substances Table (HST)” for more
information.
Hazardous Substances Table (HST)
This section describes the compliance of the OLT and ONT equipment to the CRoHS
standard when the product and subassemblies contain hazardous substances beyond
the MCV value. This information is found in this user documentation where part
numbers for the product and subassemblies are listed. It may be referenced in other
OLT and ONT documentation.
In accordance with the People’s Republic of China Electronic Industry Standard
Marking for the Control of Pollution Caused by Electronic Information Products
(SJ/T11364-2006), customers may access the Alcatel-Lucent Hazardous Substance
Table, in Chinese, from the following location:
• http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaR
oHS.pdf
Other environmental requirements
Observe the following environmental requirements when handling the P-OLT or
ONT equipment.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xix
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelines
ONT environmental requirements
See the ONT technical specification documentation for more information about
temperature ranges.
Storage
According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in
Class 1.1, weather-protected, temperature-controlled locations.
Transportation
According to EN 300-019-1-2 - Class 2.3, transportation of the OLT equipment must
be in packed, public transportation with no rain on packing allowed.
Stationary use
According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment
must be in a temperature-controlled location, with no rain allowed, and with no
condensation allowed.
Thermal limitations
When the OLT is installed in the CO or CEV, install air filters on the P-OLT. The
thermal limitations for OLT operation in a CO or CEV are:
•
•
•
•
operating temperature: 5°C to 40°C (41°F to 104°F)
short-term temperature: –5°C to 50°C (23°F to 122°F)
operating relative humidity: 5% to 85%
short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kg
Material content compliance
European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain
Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium,
hexavalent chromium, and certain flame retardants in electrical and electronic
equipment. This Directive applies to electrical and electronic products placed on the
EU market after 1 July 2006, with various exemptions, including an exemption for
lead solder in network infrastructure equipment. Alcatel-Lucent products shipped to
the EU after 1 July 2006 comply with the EU RoHS Directive.
Alcatel-Lucent has implemented a material/substance content management process.
The process is described in: Alcatel-Lucent process for ensuring RoHS Compliance
(1AA002660031ASZZA). This ensures compliance with the European Union
Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment (RoHS2). With the process equipment is
assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC)
on Technical documentation for the assessment of electrical and electronic products
with respect to the restriction of hazardous substances.
xx
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelines
End-of-life collection and treatment
Electronic products bearing or referencing the symbol shown in Figure 3, when put
on the market within the European Union (EU), shall be collected and treated at the
end of their useful life, in compliance with applicable EU and local legislation. They
shall not be disposed of as part of unsorted municipal waste. Due to materials that
may be contained in the product, such as heavy metals or batteries, the environment
and human health may be negatively impacted as a result of inappropriate disposal.
Note — In the European Union, a solid bar under the symbol for a
crossed-out wheeled bin indicates that the product was put on the
market after 13 August 2005.
Dans l'Union européenne, un bar solide sous le symbole
d'une poubelle sur roues barrée d'une croix indique que le produit
a étémis sur le marchéaprès le 13 Août 2005.
Figure 3 Recycling/take back/disposal of product symbol
At the end of their life, the OLT products are subject to the applicable local
legislations that implement the European Directive 2002/96EC on waste electrical
and electronic equipment (WEEE).
There can be different requirements for collection and treatment in different member
states of the European Union.
In compliance with legal requirements and contractual agreements, where
applicable, Alcatel-Lucent will offer to provide for the collection and treatment of
Alcatel-Lucent products bearing the logo shown in Figure 3 at the end of their useful
life, or products displaced by Alcatel-Lucent equipment offers. For information
regarding take-back of equipment by Alcatel-Lucent, or for more information
regarding the requirements for recycling/disposal of product, contact your
Alcatel-Lucent account manager or Alcatel-Lucent take back support at
takeback@alcatel-lucent.com.
Alcatel-Lucent 7368 ISAM ONT
xxi
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
This chapter provides information about the mandatory regulations that govern the
installation and operation of the optical network terminals or units (ONTs or ONUs)
in the North American or ANSI market.
Safety instructions
This section describes the safety instructions that are provided in the ONT customer
documentation and on the equipment.
Safety instruction boxes in customer documentation
The safety instruction boxes are provided in the ONT customer documentation.
Observe the instructions to meet safety requirements.
The following is an example of the Danger box.
Danger — Possibility of personal injury.
Possibilitéde blessures
The Danger box indicates that the described activity or situation may pose a threat to
personal safety. It calls attention to a situation or procedure which, if not correctly
performed or adhered to, may result in death or serious physical harm.
Do not proceed beyond a Danger box until the indicated conditions are fully
understood and met.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
xxiii
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
The following is an example of the Warning box.
Warning 1 — Possibility of equipment damage.
Possibilitéde dommages matériels
Warning 2 — Possibility of data loss.
Possibilitéde perte de données.
The Warning box indicates that the described activity or situation may, or will, cause
equipment damage, loss of data, or serious performance problems. It identifies a
possible equipment-damaging situation or provides essential information to avoid
the degradation of system operations or data.
Do not proceed beyond a warning until the indicated conditions are fully understood
and met.
The following is an example of the Caution box.
Caution 1 — Possibility of service interruption.
Possibilitéd'interruption de service
Caution 2 — Service interruption.
Interruption de service.
The Caution box indicates that the described activity or situation may, or will, cause
service interruption.
Do not proceed beyond a caution until the indicated conditions are fully understood
and met.
The following is an example of the Note box.
Note — Information of special interest.
L'information d'intérêt spécial.
The Note box provides information that assists the personnel working with ONTs. It
does not provide safety-related instructions.
Safety-related labels
The ONT equipment is labeled with specific safety compliance information and
instructions that are related to a variant of the ONT. Observe the instructions on the
safety labels.
Table 1 provides examples of the text in the various ONT safety labels.
Table 1 Safety labels
Description
Label text
UL compliance
Communication service equipment US listed. Type 3R enclosure Rainproof.
TUV compliance
Type 3R enclosure - Rainproof.
ESD warning
Caution: This assembly contains electrostatic sensitive device.
(1 of 2)
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
Description
Label text
Laser classification
Class 1 laser product
Laser product compliance
This laser product conforms to all applicable standards of 21 CFR
1040.10 at date of manufacture.
FCC standards compliance
Tested to comply with FCC standards for home or office use.
CDRH compliance
Complies with 21 CFR 1040.10 and 1040.11 except for deviations
pursuant to Laser Notice No. 50, dated June 24, 2007
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Canadian standard
compliance (modular ONT)
This Class A digital apparatus complies with Canadian ICES-003.
Canadian standard
compliance (outdoor ONT)
This Class B digital apparatus complies with Canadian ICES-003.
CE marking
There are various CE symbols for CE compliance.
(2 of 2)
Figure 1 shows a sample safety label on the ONT equipment.
Figure 1 Sample safety label on the ONT equipment
Tested to Comply
with FCC Standards
FOR HOME OR OFFICE USE
®
COMMUNICATION SERVICE EQUIPMENT
US LISTED
27FY
Type 3R Enclosure - Rainproof
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
numerique de la class A est conforme a la norme NMB-003 du Canada
CAUTION
This Assembly Contains Electrostatic Sensitive Devices
18533
Safety standards compliance
This section describes the ONT compliance with North American safety standards.
Warning — Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Les changements ou modifications de cette unité
non expressément approuvés par la partie responsable de la
conformitépourraient annuler l'autoritéde l'utilisateur àutiliser
l'équipement.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
EMC, EMI, and ESD standards compliance
The ONT equipment complies with the following requirements:
• Federal Communications Commission (FCC) CFR 47, Part 15, Subpart B, Class
A requirements for OLT equipment
• GR-1089-CORE requirements, including:
• Section 3 Electromagnetic Interference, Emissions Radiated and Conducted
• Section 3 Immunity, Radiated and Conducted
• Section 2 ESD Discharge Immunity: System Level Electrostatic Discharge and EFT
Immunity: Electrically Fast Transients
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
• Consult the dealer or an experienced radio/TV technician for help.
Equipment safety standard compliance
The ONT equipment complies with the requirements of UL60950-1, Outdoor ONTs
to “Communication Service Equipment” (CSE) and Indoor ONTs to Information
Technology Equipment (ITE).
Environmental standards compliance
The ONT equipment complies with the following standards:
• GR-63-CORE (NEBS): requirements related to operating, storage, humidity,
•
•
•
•
xxvi
altitude, earthquake, office vibration, transportation and handling, fire resistance
and spread, airborne contaminants, illumination, and acoustic noise
GR-487-CORE: requirements related to rain, chemical, sand, and dust
GR-487 R3-82: requirements related to condensation
GR-3108: Requirements for Network Equipment in the Outside Plant (OSP)
TP76200: Common Systems Equipment Interconnections Standards
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
Laser product standards compliance
The ONT equipment complies with 21 CFR 1040.10 and CFR 1040.11, except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007” or to 21 CFR
1040.10 U.S. Center for Devices and Radiological Health (CDRH) of the Food and
Drug Administration (FDA) Laser Notice 42 for ONTs containing Class 1 Laser
modules certified by original manufactures.
Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such
as ALU ONTs shall leave the following Laser Safety cautions with the end user.
a) “Class 1 Laser Product”
b) “Caution – Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.”
Figure 2 shows a laser product label.
Figure 2 Sample laser product label showing CDRH 21 CFR compliance
4P92 No User Serviceable Parts Inside. Refer All Servicing To Qualified Personnel.
12VDC
2.5A
I.T.E
Complies with 21 CFR 1040.10 and
1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
22813
Resistibility requirements compliance
The ONT equipment complies with the requirements of ITU Recommendation K.21
for resistibility of telecommunication equipment installed in customer premises to
overvoltage and overcurrents.
Laser safety guidelines
Only qualified service personnel who are extremely familiar with laser radiation
hazards should install or remove the fiber optic cables and units in this system.
Observe the following warnings when you perform installation, operations, and
maintenance tasks on the ONT equipment.
Danger — There may be invisible laser radiation at the fiber optic
cable when the cable is removed from the connector. Avoid direct
exposure to beam.
Il peut y avoir un rayonnement laser invisible sur le
câble à fibre optique lorsque le câble est retiré du connecteur.
Éviter l'exposition directe au rayon
Alcatel-Lucent 7368 ISAM ONT
xxvii
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
Observe the following danger for a laser hazard. Eyes can be damaged when they are
exposed to a laser beam. Take necessary precautions before you plug in the optical
modules.
Danger — Possibility of equipment damage. Risk of eye damage by
laser radiation.
Possibilitéde dommages matériels. Risque de lésions
oculaires par un rayonnement laser.
Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such
as ALU ONTs shall leave the following Laser Safety cautions with the end user.
a) “Class 1 Laser Product”
b) “Caution – Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.”
Laser warning labels
The following figures show sample labels related to laser product, classification and
warning.
Figure 3 shows a laser product label.
Figure 3 Laser product label
18455
Figure 4 shows a laser classification label. Laser classification labels may be
provided in other languages.
Figure 4 Laser classification label
CLASS 1 LASER PRODUCT
PRODUCTO LASER CLASE 1
CLASE 1 DEL LASER
LASER CLASSE 1
18992
xxviii
Alcatel-Lucent 7368 ISAM ONT
Edition 01
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
Figure 5 shows a laser warning label and an explanatory label for laser products.
Explanatory labels may be provided in other languages. The explanatory label
provides the following information:
• a warning that calls attention to the invisible laser radiation
• an instruction against staring into the beam or viewing directly with optical
instruments
• wavelength
• normal output power
• maximum output power
Figure 5 Laser warning labels
INVISIBLE LASER RADIATION
DO NOT STARE INTO BEAM
OR VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
Wavelength(s): xxxx nm
Normal output power: xx m W
Max output power: yyy m W
Laser Warning Label
Laser Warning Label
CLASS 1 LASER PRODUCT
RAYONNEMENT LASER CLASSE 1
RAYONNEMENT LASER INVISIBLE EVITER
TOUTE EXPOSITION AU FAISCEAU
NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE
CLASE 1 DEL LASER
RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL
RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO
INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE
WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM.
Laser Warning Label
18993
Laser classification
The ONT is classified as a Class 1 laser product based on its transmit optical output.
For Class 1 laser products, lasers are safe under reasonably foreseeable conditions of
operation, including the use of optical instruments for intrabeam viewing.
Figure 6 shows a sample laser product safety label on the ONT equipment.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xxix
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
Figure 6 Sample laser product safety label on the ONT equipment
CLASS 1 LASER PRODUCT
THIS LASER PRODUCT CONFORMS TO ALL APPLICABLE
STANDARDS OF 21 CFR 1040.10 AT DATE OF MANUFACTURE.
MANUFACTURED:
MONTH
YEAR
18532
Transmit optical output
The maximum transmit optical output of an ONT is +5 dBm.
Normal laser operation
In normal operation, fiber cable laser radiation is always off until it receives signal
from the line terminal card.
Operating personnel must observe the instructions on the laser explanatory label
before plugging in the optical module.
Danger — Risk of eye damage by laser radiation.
Risque de lésions oculaires par un rayonnement laser.
Location class
Use cable supports and guides to protect the receptacles from strain.
Electrical safety guidelines
This section provides the electrical safety guidelines for the ONT equipment.
Note — The ONTs comply with the U.S. National Electrical Code.
However, local electrical authorities have jurisdiction when there are
differences between the local and U.S. standards.
Les ONT sont conformes àla US National Electrical Code.
Cependant, les autorités locales électriques ont compétence quand il
ya des différences entre les normes locales et américaines.
Power supplies
The use of any non-Alcatel-Lucent approved power supplies or power adapters is not
supported or endorsed by Alcatel-Lucent. Such use will void any warranty or support
contract with Alcatel-Lucent. Such use greatly increases the danger of damage to
equipment or property.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelines
Cabling
The following are the guidelines regarding cables used for the ONT equipment:
• Use only cables approved by the relevant national electrical code.
• Use cables suitable for outdoor use for outdoor installation of ONTs.
• The ONTs have been evaluated for use with external POTS wiring without
primary protection that may not exceed 140 ft (43 m) in reach. However, the
power cable must not exceed 100 ft (31 m).
Protective earth
Earthing and bonding of the ONTs must comply with the requirements of NEC
article 250 or local electrical codes.
ESD safety guidelines
The ONT equipment is sensitive to ESD. Operations personnel must observe the
following ESD instructions when they handle the ONT equipment.
Caution — This equipment is ESD sensitive. Proper ESD protections
should be used when entering the TELCO Access portion of the ONT.
Cet équipement est sensible ESD. Protections ESD
appropriées doivent être utilisées lors de l'entrée de la partie TELCO
accès de l'ONT
During installation and maintenance, service personnel must wear wrist straps to
prevent damage caused by ESD.
Alcatel-Lucent recommends that you prepare the site before you install the ONT
equipment. In addition, you must control relative humidity, use static dissipating
material for furniture or flooring, and restrict the use of air conditioning.
Environmental requirements
See the ONT technical specification documentation for temperature ranges for
ONTs.
During operation in the supported temperature range, condensation inside the ONT
caused by humidity is not an issue. To avoid condensation caused by rapid changes
in temperature and humidity, Alcatel-Lucent recommends:
• The door of the ONT not be opened until temperature inside and outside the
enclosure has stabilized.
• If the door of the ONT must be opened after a rapid change in temperature or
humidity, use a dry cloth to wipe down the metal interior to prevent the risk of
condensation.
• When high humidity is present, installation of a cover or tent over the ONT helps
prevent condensation when the door is opened.
Alcatel-Lucent 7368 ISAM ONT
xxxi
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Contents
Preface
iii
Scope
............................................................................................... iii
Audience ............................................................................................... iii
Required knowledge ................................................................................... iii
Acronyms and initialisms ............................................................................. iii
Assistance and ordering phone numbers ........................................................... iv
Alcatel-Lucent quality processes .................................................................... iv
Safety information ..................................................................................... iv
Documents .............................................................................................. iv
Procedure 1 To download a ZIP file package of the customer
documentation.................................................................... iv
Procedure 2 To access individual documents ...................................... v
Special information ..................................................................................... v
Procedures with options or substeps ................................................. v
Procedure 3 Example of options in a procedure.................................. vi
Procedure 4 Example of required substeps in a procedure ..................... vi
Multiple PDF document search....................................................................... vi
Procedure 5 To search multiple PDF files for a common term ................. vi
ETSI ONT safety guidelines
ix
Safety instructions ..................................................................................... ix
Safety instruction boxes .............................................................. ix
Safety-related labels ................................................................... x
Safety standards compliance......................................................................... xi
EMC, EMI, and ESD compliance....................................................... xi
Equipment safety standard compliance ............................................ xi
Environmental standard compliance ............................................... xii
Laser product standard compliance ................................................ xii
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xxxiii
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Contents
Resistibility requirements compliance ............................................. xii
Acoustic noise emission standard compliance .................................... xii
Electrical safety guidelines.......................................................................... xii
Power supplies......................................................................... xii
Cabling .................................................................................. xii
Protective earth ...................................................................... xiii
ESD safety guidelines ................................................................................ xiii
Laser safety guidelines .............................................................................. xiii
Laser classification................................................................... xiii
Transmit optical output .............................................................. xv
Normal laser operation ............................................................... xv
Location class .......................................................................... xv
Environmental requirements ........................................................................xvi
ETSI environmental and CRoHS guidelines
xvii
Environmental labels ................................................................................ xvii
Overview .............................................................................. xvii
Environmental related labels....................................................... xvii
Hazardous Substances Table (HST)................................................................. xix
Other environmental requirements ................................................................xix
ONT environmental requirements .................................................. xx
Storage.................................................................................. xx
Transportation ......................................................................... xx
Stationary use ......................................................................... xx
Thermal limitations ................................................................... xx
Material content compliance ........................................................ xx
End-of-life collection and treatment ..............................................xxi
ANSI ONT safety guidelines
xxiii
Safety instructions .................................................................................. xxiii
Safety instruction boxes in customer documentation ......................... xxiii
Safety-related labels ............................................................... xxiv
Safety standards compliance....................................................................... xxv
EMC, EMI, and ESD standards compliance ....................................... xxvi
Equipment safety standard compliance ......................................... xxvi
Environmental standards compliance ............................................ xxvi
Laser product standards compliance .............................................xxvii
Resistibility requirements compliance ...........................................xxvii
Laser safety guidelines .............................................................................xxvii
Laser warning labels ............................................................... xxviii
Laser classification.................................................................. xxix
Transmit optical output ............................................................. xxx
Normal laser operation .............................................................. xxx
Location class ......................................................................... xxx
xxxiv
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Contents
Electrical safety guidelines......................................................................... xxx
Power supplies........................................................................ xxx
Cabling ................................................................................ xxxi
Protective earth ..................................................................... xxxi
ESD safety guidelines ............................................................................... xxxi
Environmental requirements ...................................................................... xxxi
1—
G-240W-B unit data sheet
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
2—
Install a G-240W-B indoor ONT
2.1
2.2
2.3
2.4
2.5
2.6
3—
4—
3-1
Purpose ................................................................................... 3-2
General ................................................................................... 3-2
Prerequisites ............................................................................. 3-2
Recommended tools .................................................................... 3-2
Safety information ...................................................................... 3-3
Procedure ................................................................................ 3-4
Configure a G-240W-B indoor ONT
4.1
4.2
2-1
Purpose ................................................................................... 2-2
General ................................................................................... 2-2
Prerequisites ............................................................................. 2-2
Recommended tools .................................................................... 2-2
Safety information ...................................................................... 2-3
Procedure ................................................................................ 2-4
Replace a G-240W-B indoor ONT
3.1
3.2
3.3
3.4
3.5
3.6
1-1
G-240W-B part numbers and identification ......................................... 1-2
G-240W-B general description ........................................................ 1-3
G-240W-B software and installation feature support.............................. 1-4
G-240W-B interfaces and interface capacity ....................................... 1-4
G-240W-B connections and components .......................................... 1-5
G-240W-B LEDs .......................................................................... 1-6
G-240W-B detailed specifications .................................................... 1-7
G-240W-B GEM ports and T-CONTs ................................................... 1-8
G-240W-B performance monitoring statistics....................................... 1-9
G-240W-B functional blocks .......................................................... 1-11
G-240W-B standards compliance .................................................... 1-13
FCC statement ....................................................................... 1-13
FCC Radiation Exposure Statement .............................................. 1-13
G-240W-B special considerations .................................................... 1-14
Wi-Fi service ......................................................................... 1-14
G-240W-B ONT considerations and limitations ................................. 1-14
4-1
General ................................................................................... 4-2
HGU mode GUI configuration.......................................................... 4-2
Login ................................................................................... 4-2
Procedure 4-1 Login to web-based GUI .......................................... 4-2
Device and connection status ...................................................... 4-3
Procedure 4-2 Device information retrieval..................................... 4-4
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xxxv
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Contents
4.3
4.4
xxxvi
Procedure 4-3 LAN status retrieval ............................................... 4-5
Procedure 4-4 WAN status retrieval .............................................. 4-6
Procedure 4-5 WAN status IPv6 retrieval ........................................ 4-8
Procedure 4-6 Home networking information retrieval ....................... 4-9
Procedure 4-7 Optics module status retrieval ................................. 4-10
Network configuration.............................................................. 4-11
Procedure 4-8 LAN networking configuration .................................. 4-12
Procedure 4-9 LAN IPv6 networking configuration ............................ 4-13
Procedure 4-10 WAN networking configuration................................ 4-15
Procedure 4-11 WiFi 2.4G networking configuration ......................... 4-16
Procedure 4-12 WiFi 5G networking configuration ............................ 4-18
Procedure 4-13 Routing configuration .......................................... 4-19
Procedure 4-14 DNS configuration ............................................... 4-20
Procedure 4-15 TR-069 configuration ........................................... 4-21
Security configuration .............................................................. 4-22
Procedure 4-16 Firewall configuration .......................................... 4-23
Procedure 4-17 MAC filter configuration ....................................... 4-24
Procedure 4-18 IP filter configuration .......................................... 4-25
Procedure 4-19 DMZ and ALG configuration.................................... 4-26
Application configuration .......................................................... 4-27
Procedure 4-20 Port forwarding configuration ................................ 4-27
Procedure 4-21 DDNS configuration ............................................. 4-28
Procedure 4-22 NTP configuration ............................................... 4-29
Procedure 4-23 USB storage configuration ..................................... 4-30
Maintenance ......................................................................... 4-31
Procedure 4-24 Password configuration ........................................ 4-31
Procedure 4-25 SLID configuration .............................................. 4-32
Procedure 4-26 Device management ............................................ 4-33
Procedure 4-27 Backup and restore ............................................. 4-34
Procedure 4-28 Upgrade firmware............................................... 4-34
Procedure 4-29 Reboot ONT ...................................................... 4-35
Procedure 4-30 Restore factory defaults ....................................... 4-36
Procedure 4-31 Diagnose connections........................................... 4-37
Procedure 4-32 View log files .................................................... 4-38
SFU mode GUI configuration ......................................................... 4-39
Login .................................................................................. 4-39
Procedure 4-33 Login to web-based GUI ........................................ 4-39
Device and connection status ..................................................... 4-40
Procedure 4-34 Device information retrieval .................................. 4-41
Maintenance ......................................................................... 4-42
Procedure 4-35 Password configuration ........................................ 4-42
Procedure 4-36 LOID configuration .............................................. 4-43
Procedure 4-37 SLID configuration .............................................. 4-44
Operator ID.............................................................................. 4-44
Procedure 4-38 Modify the operator ID using OLT ............................ 4-45
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Contents
List of figures
Figure 1 PSE certification ............................................................................ xi
Figure 2 Laser product label .......................................................................xiv
Figure 3 Laser classification label .................................................................xiv
Figure 4 Laser warning labels ...................................................................... xv
Figure 1 Products below MCV value label ...................................................... xviii
Figure 2 Products above MCV value label ........................................................xix
Figure 3 Recycling/take back/disposal of product symbol ....................................xxi
Figure 1 Sample safety label on the ONT equipment.......................................... xxv
Figure 2 Sample laser product label showing CDRH 21 CFR compliance ..................xxvii
Figure 3 Laser product label .................................................................... xxviii
Figure 4 Laser classification label .............................................................. xxviii
Figure 5 Laser warning labels .................................................................... xxix
Figure 6 Sample laser product safety label on the ONT equipment......................... xxx
Figure 1-1 G-240W-B indoor ONT physical connections ....................................... 1-5
Figure 1-2 G-240W-B indoor ONT LEDs........................................................... 1-6
Figure 1-3 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and
without RF video ................................................................ 1-11
Figure 1-4 G-240W-B ONT hardware block ..................................................... 1-12
Figure 2-1 Wall mounting keyholes on G-240W-B indoor ONTs .............................. 2-4
Figure 2-2 G-240W-B indoor ONT connections (back view) ................................... 2-5
Figure 3-1 G-240W-B indoor ONT connections .................................................. 3-4
Figure 4-1 Web login window ..................................................................... 4-3
Figure 4-2 Device Information window .......................................................... 4-4
Figure 4-3 LAN status window..................................................................... 4-5
Figure 4-4 WAN status window .................................................................... 4-6
Figure 4-5 WAN status IPv6 window .............................................................. 4-8
Figure 4-6 Home networking information window ............................................. 4-9
Figure 4-7 Optics module status window ....................................................... 4-10
Figure 4-8 LAN network window ................................................................. 4-12
Figure 4-9 LAN IPv6 network window ........................................................... 4-13
Figure 4-10 WAN network window............................................................... 4-15
Figure 4-11 WiFi 2.4G network window ........................................................ 4-16
Figure 4-12 WiFi 5G network window ........................................................... 4-18
Figure 4-13 Routing network window ........................................................... 4-19
Figure 4-14 DNS network window................................................................ 4-20
Figure 4-15 TR-069 network window ............................................................ 4-21
Figure 4-16 Firewall window ..................................................................... 4-23
Figure 4-17 MAC filter window ................................................................... 4-24
Figure 4-18 IP filter window ...................................................................... 4-25
Figure 4-19 DMZ and ALG window ............................................................... 4-26
Figure 4-20 Port forwarding window ............................................................ 4-27
Figure 4-21 DDNS window......................................................................... 4-28
Figure 4-22 NTP window .......................................................................... 4-29
Figure 4-23 USB storage window................................................................. 4-30
Figure 4-24 Password window .................................................................... 4-31
Figure 4-25 SLID configuration window ......................................................... 4-32
Figure 4-26 Device management window ...................................................... 4-33
Figure 4-27 Backup and Restore window ....................................................... 4-34
Figure 4-28 Firmware upgrade window ......................................................... 4-34
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xxxvii
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Contents
Figure 4-29
Figure 4-30
Figure 4-31
Figure 4-32
Figure 4-33
Figure 4-34
Figure 4-35
Figure 4-36
Figure 4-37
Reboot window ...................................................................... 4-35
Factory default window ............................................................ 4-36
Diagnose window .................................................................... 4-37
Log window ........................................................................... 4-38
Web login window ................................................................... 4-40
Device Information window ........................................................ 4-41
Password window .................................................................... 4-42
LOID configuration window ........................................................ 4-43
SLID configuration window ......................................................... 4-44
List of tables
Table 1 Safety labels .................................................................................. x
Table 1 Safety labels .............................................................................. xxiv
Table 1-1 Identification of G-240W-B indoor ONTs ............................................. 1-2
Table 1-2 G-240W-B power supply ................................................................ 1-3
Table 1-3 G-240W-B indoor ONT interface connection capacity ............................. 1-5
Table 1-4 G-240W-B indoor ONT physical connections......................................... 1-5
Table 1-5 G-240W-B indoor ONT LEDs ............................................................ 1-7
Table 1-6 G-240W-B indoor ONT physical specifications....................................... 1-8
Table 1-7 G-240W-B indoor ONT power consumption specifications ........................ 1-8
Table 1-8 G-240W-B indoor ONT environmental specifications............................... 1-8
Table 1-9 G-240W-B indoor ONT capacity for GEM ports and T-CONTs...................... 1-8
Table 1-10 Package P ONTs ONTENET performance monitoring statistics .................. 1-9
Table 1-11 Package P ONTs ONTL2UNI performance monitoring statistics ................ 1-10
Table 1-12 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI,
PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance
monitoring statistics ............................................................ 1-10
Table 1-13 Package P ONTs PONONTTC aggregate performance monitoring
statistics .......................................................................... 1-10
Table 1-14 G-240W-B ONT considerations and limitations ................................... 1-15
Table 4-1 Device Information parameters ....................................................... 4-4
Table 4-2 LAN status parameters.................................................................. 4-5
Table 4-3 WAN status parameters ................................................................. 4-7
Table 4-4 WAN status IPv6 parameters ........................................................... 4-8
Table 4-5 Home networking parameters ......................................................... 4-9
Table 4-6 Optics module status parameters .................................................... 4-10
Table 4-7 LAN network parameters .............................................................. 4-12
Table 4-8 LAN IPv6 network parameters ........................................................ 4-13
Table 4-9 WAN network parameters ............................................................. 4-15
Table 4-10 WiFi 2.4G network parameters ..................................................... 4-17
Table 4-11 WiFi 5G network parameters ........................................................ 4-18
Table 4-12 Routing network parameters ........................................................ 4-20
Table 4-13 DNS network parameters............................................................. 4-21
Table 4-14 TR-069 network parameters ......................................................... 4-21
Table 4-15 Firewall parameters .................................................................. 4-23
Table 4-16 MAC filter parameters ................................................................ 4-24
Table 4-17 IP filter parameters ................................................................... 4-25
Table 4-18 DMZ and ALG parameters ............................................................ 4-26
xxxviii
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Contents
Table 4-19 Port forwarding parameters ......................................................... 4-27
Table 4-20 DDNS parameters...................................................................... 4-28
Table 4-21 NTP parameters ....................................................................... 4-29
Table 4-22 USB storage parameters.............................................................. 4-30
Table 4-23 Password parameters ................................................................. 4-32
Table 4-24 SLID configuration parameters ...................................................... 4-32
Table 4-25 Device management parameters ................................................... 4-33
Table 4-26 Device Information parameters ..................................................... 4-41
Table 4-27 Password parameters ................................................................. 4-42
Table 4-28 SLID configuration parameters ...................................................... 4-44
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
xxxix
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1—
G-240W-B unit data sheet
1.1 G-240W-B part numbers and identification
1.2 G-240W-B general description
1-2
1-3
1.3 G-240W-B software and installation feature support
1.4 G-240W-B interfaces and interface capacity
1.5 G-240W-B LEDs
1-4
1-6
1.6 G-240W-B detailed specifications
1.7 G-240W-B GEM ports and T-CONTs
1-7
1-8
1.8 G-240W-B performance monitoring statistics
1.9 G-240W-B functional blocks
1-9
1-11
1.10 G-240W-B standards compliance
1-13
1.11 G-240W-B special considerations
1-14
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
1-4
1-1
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
1.1
G-240W-B part numbers and identification
Table 1-1 provides part numbers and identification information for the G-240W-B
indoor ONT.
Table 1-1 Identification of G-240W-B indoor ONTs
Mnemonic
Ordering kit
part number
Provisioning
number
Description
CLEI
CPR
ECI/
Bar
code
G-240W-B
3FE 56636 AA
3FE 56756 BAAA
Package P 2 POTS ports, 4 10/100/1000
Base-T Ethernet interfaces, and
802.11b/g/n/ac Wi-Fi radio with
on/off switch.
This ONT also has 2 USB ports, 1 USB
3.0 and 1 USB 2.0.
Includes 3-pin wall-mounted US AC/DC
adapter.
—
—
—
3FE 56636 BA
3FE 56756 AABA
Package P 2 POTS ports, 4 10/100/1000
Base-T Ethernet interfaces, and
802.11b/g/n/ac Wi-Fi radio with
on/off switch.
This ONT also has 2 USB ports, 1 USB
3.0 and 1 USB 2.0.
Includes 2-pin wall-mounted European
(EU) AC/DC adapter.
—
—
—
3FE 56636 CA
3FE 56756 AABA
Package P 2 POTS ports, 4 10/100/1000
Base-T Ethernet interfaces, and
802.11b/g/n/ac Wi-Fi radio with
on/off switch.
This ONT also has 2 USB ports, 1 USB
3.0 and 1 USB 2.0.
Includes 3-pin wall-mounted British
(UK) AC/DC adapter.
—
—
—
3FE 56636 CB
3FE 56756 ABBA
Package P 2 POTS ports, 4 10/100/1000
Base-T Ethernet interfaces, and
802.11b/g/n/ac Wi-Fi radio with
on/off switch.
This ONT also has 2 USB ports, 1 USB
3.0 and 1 USB 2.0.
Includes 3-pin wall-mounted British
(UK) AC/DC adapter.
—
—
—
Customer-spe
cific
Table 1-2 provides power supply ordering information about the G-240W-B ONT.
For more information on power supplies, see the 7368 ISAM ONT Power Supply and
UPS Guide.
1-2
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Table 1-2 G-240W-B power supply
Power model
Power information
Customer category
or country
compliance tested
for
Mass Power
36 Watt AC/DC power adapter
ANSI municipality
United States,
Canada
1.2
Notes
G-240W-B general description
G-240W-B indoor ONTs provide the subscriber interface for the network by
terminating the PON interface and converting it to user interfaces that directly
connect to subscriber devices. The ONT is compatible with all existing subscriber
equipment, including analog phones with both tone and rotary dial capabilities,
cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and
Type III).
G-240W-B indoor ONTs provide the following functions:
• Single fiber GPON interface with 1.244Gbit/s upstream and 2.488Gbit/s
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
downstream data rates
Advanced data features such as VLAN tag manipulation, classification, and
filtering.
Traffic classification and QoS capability
Analog Telephone Adapter (ATA) function integrated based on SIP (RFC3261)
and H.248, with various CLASS services supported, including Caller ID, Call
Waiting, Call Forwarding, and Call Transfer
5 REN per line
Multiple voice Codec
MDI/MDIX auto-negotiation
Line Rate L2 traffic
Internal Switch
UPnP IGD1.0 support
Bridged mode or routed mode per LAN port
Optics that support received signal strength indication (RSSI)
Internal DHCP server, with configurable DHCP pool and gateway
WPS on wireless authorization support
Configurable Wi-Fi tx power from 100mw to 500mw, in 100mw increments.
Enhanced ONT; SSH-Telnet-FTP and http server are disabled from the WAN
side
Concurrent 802.11n 3x3 MIMO in 2.4GHz and 802.11ac 4x4 MIMO in 5GHz
64/128 WEP encryption
WPA, WPA-PSK/TKIP
WPA2, WPA2-PSK/AES
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
1-3
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
• support for multiple SSIDs (private and public instances); contact your ALU
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.3
representative for further details.
WLAN on/off push button
WPS/PBC buttons (for 2.4G and 5G)
Ethernet-based Point-to-Point (PPPoE)
Network Address Translation (NAT)
Network Address Port Translation (NAPT)
ALG and UpnP port forwarding
DMZ
IP/MAC filter
Multi-level firewall
DNS server
DHCP client/server
support for HT40 mode for increased channel bandwidth
support for up to 20 simultaneous wireless connections
External USB HD (Hard Drive) support, accessible to all LAN devices
G-240W-B software and installation feature support
For information on installing or replacing the G-240W-B see:
• Install a G-240W-B indoor ONT
• Replace a G-240W-B indoor ONT
For information on the following topics, see the 7368 ISAM ONT Product Overview
Guide:
•
•
•
•
•
•
•
•
1.4
ONT and MDU general descriptions of features and functions
Ethernet interface specifications
POTS interface specifications
RSSI specifications
Wi-Fi specifications
ONT optical budget
SLID entry via Ethernet port
ONT management using an ONT interface
G-240W-B interfaces and interface capacity
Table 1-3 describes the supported interfaces and interface capacity for G-240W-B
indoor ONTs.
1-4
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Table 1-3 G-240W-B indoor ONT interface connection capacity
ONT type
and model
Maximum capacity
POTS
10/
100
BASE-T
10/
100/
1000
BASE-T
RF video
(CATV)
MoCA
VDSL2
E1/T1
Local craft
GPON
SC/
APC
G-240W-B (1)
—
—
—
—
—
—
Note
(1)
The G-240W-B ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch.
G-240W-B connections and components
Figure 1-1 shows the physical connections for G-240W-B indoor ONTs,
Figure 1-1 G-240W-B indoor ONT physical connections
Wireless
On/Off
button
USB 3.0
USB 2.0
USB
ports
TEL1
TEL2
POTS
ports (2)
(RJ-11)
LAN1
LAN2
LAN3
LAN4
POWER
ON/OFF
UPS
Ethernet
Reset
On/Off
ports (4)
button
button
Power
(RJ-45) Wi-Fi
input
security
buttons (2)
Fiber
optic
port
24614
Table 1-4 describes the physical connections for G-240W-B indoor ONTs.
Table 1-4 G-240W-B indoor ONT physical connections
Connection (1)
Description
USB ports
This connection is provided through 2 USB ports, 1 USB 3.0 and 1 USB
2.0. The ONT supports external USB hard drives that can be made
accessible to all LAN devices.
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
1-5
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Connection (1)
Description
POTS ports
This connection is provided through RJ-11 ports. Up to two POTS
connections are supported.The POTS ports support voice services.
Ethernet ports
This connection is provided through Ethernet RJ-45 connectors. Up to
four 10/100/1000 Base-T Ethernet interfaces are supported.The
Ethernet ports can support both data and in-band video services on all
four interfaces.
WPS buttons
The Wi-Fi Protected Setup buttons are labeled WPS2.4G and WPS5G.
These buttons enable and disable WLAN data encryption.
WLAN button
Wi-Fi service is compliant with IEEE 802.11 standards and is enabled
and disabled using the WLAN button.
Reset button
This button resets the ONT to the factory defaults.
Power input
This connection is provided through the power connector. A power
cable fitted with a barrel connector is used to make the connection.
On/Off button
This button turns the ONT on or off.
(2 of 2)
Note
(1)
1.5
The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the
power connector.
G-240W-B LEDs
Figure 1-2 shows the G-240W-B indoor ONT LEDs.
Figure 1-2 G-240W-B indoor ONT LEDs
LAN1
LINK
AUTH
LAN3
LAN2
TEL1
LAN4
VOIP
TEL2
WPS
2.4G
BTR
WPS
5G
WLAN
2.4G
WLAN
5G
USB
POWER
INTERNET
POWER
BTR
LINK
AUTH
LAN1
LAN2
LAN3
LAN4
TEL1
TEL2
VOIP
WPS
2.4G
WPS
5G
WLAN
2.4G
WL A N
5G
USB
INTE RNET
24615
Table 1-5 provides LED descriptions for G-240W-B indoor ONTs.
1-6
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Table 1-5 G-240W-B indoor ONT LEDs
Indicator
Power
LED color and
behavior
LED behavior description
Green solid
Power on
Red solid
Light failed on startup (for example corrupt flash), or self test failed on startup,
or self test failed during regular operation or when executed over OMCI
Power off
Off
BTR
Off
Green
Battery alarm set or battery not provisioned (not affected by AC power failure)
Battery charged; no battery alarms
Link
Green solid
Off
GPON link between ONT and OLT is operating normally
GPON link is down or no link connected
Auth
Green solid
ONT is authorized
Green flashing
ONT is process of ranging or synchronizing on OMCI
ONT is not authorized
Off
LAN 1 to 4
Green solid
Green flashing
Off
TEL 1 to 2
VOIP
WPS
2.4G and 5G
WLAN
2.4G and 5G
USB
INTERNET
LAN activity is present (in either direction)
ONT power is off or Ethernet is not connected
Green solid
Green flashing
Off hook
Off
On hook
Green solid
VOIP service is OK
Off
VOIP service is not OK
Green solid
Green flashing
Wireless LAN link is up
Wireless LAN link activity
Off
Wireless LAN link is down or no link is connected
Green solid
Green flashing
Wireless is enabled
Off
Wireless is down or no link is connected
Green solid
Green flashing
At least one USB device is connected
There is traffic activity on at least on USB device
Off
No USB device is connected
Green solid
HSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP,
or static, and no traffic has been detected; b) the session is dropped due to idle
timeout but the PON link is still present.
PPPoE or DHCP connection in progress
Green flashing
Off
1.6
Ethernet is linked
Call in or talking
There is traffic on wireless interface
HSI WAN is not connected: a) there is no physical interface connection; b) the
device is in bridged mode without an assigned IP address; c) the session has been
dropped for reasons other than idle timeout.
G-240W-B detailed specifications
Table 1-6 lists the physical specifications for G-240W-B indoor ONTs.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
1-7
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Table 1-6 G-240W-B indoor ONT physical specifications
Description
Specification
Length
11.8 in. (300 mm)
Width
7.3 in. (185 mm)
Height
1.4 in. (36 mm)
Weight [within ± 0.5 lb (0.23 kg)]
1.33 lb (0.61 kg)
Table 1-7 lists the power consumption specifications for G-240W-B indoor ONT.
Table 1-7 G-240W-B indoor ONT power consumption specifications
Mnemonic
Maximum power
(Not to exceed)
Condition
Minimum power
Condition
G-240W-B
(3FE 56525
AAAA)
30 W
2 POTS off-hook, 4
10/100/1000 Base-T
Ethernet, Wi-Fi operational
12 W
2 POTS on-hook, other
interfaces/services not
provisioned
Table 1-8 lists the environmental specifications for G-240W-B indoor ONT.
Table 1-8 G-240W-B indoor ONT environmental specifications
Mounting method
Temperature range and humidity
Altitude
On desk or wall
mounted
Operating: 23°F to 113°F (-5°C to 45°C)
ambient temperature
10% to 90% relative humidity, non-condensing
Contact your Alcatel-Lucent technical support
representative for more information
Storage: Contact your Alcatel-Lucent support
representative for more information
1.7
G-240W-B GEM ports and T-CONTs
Table 1-9 lists the maximum number of supported T-CONTs and GEM ports. See the
appropriate release Customer Release Notes for the most accurate list of supported
devices.
Table 1-9 G-240W-B indoor ONT capacity for GEM ports and T-CONTs
ONT or MDU
Maximum
Notes
64
—
Package P ONTs
GEM ports per indoor or
outdoor ONT
(1 of 2)
1-8
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
ONT or MDU
Maximum
Notes
T-CONTs per indoor or outdoor
ONT
32
—
(2 of 2)
G-240W-B performance monitoring statistics
The following section identifies the supported performance monitoring statistics for
G-240W-B ONTs. A check mark indicates the statistic is supported on that ONT. An
empty cell indicates the statistic is not supported. The following tables are
categorized by supported alarm types:
• Table 1-10 provides statistics for ONTENET type counters
• Table 1-11 provides statistics for ONTL2UNI type counters
• Table 1-12 provides statistics for PONONTTC, PONONTMCTC,
PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, and
PONONTTCVOIP type counters
• Table 1-13 provides statistics for PONONTTC aggregate type counters
Note — If you have trouble accessing G-240W-B ONTs performance
monitoring statistics using TL1, please contact your Alcatel-Lucent
support representative for more information about how to access and
retrieve performance monitoring type counters.
Si vous avez des difficultés àaccéder statistiques de suivi
de la performance G-240W-B ONT utilisant TL1, se il vous plaî
contacter votre représentant de support d'Alcatel-Lucent pour plus
d'informations sur la façon d'accéder et de récupérer des compteurs
de performance de type de surveillance.
Table 1-10 Package P ONTs ONTENET performance monitoring statistics
LC
RBO
SCF
MCF
DT
IMTE
CSE
AE
IMRE
FTL
TBO
SQE
G-240W-B (1)
ONTENET statistics
EC
ONT
FCSE
1.8
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Note
(1)
A 5 second polling window limitation exists on the ONT, therefore the margin of error for each
15-min window is 5 seconds
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Table 1-11 Package P ONTs ONTL2UNI performance monitoring statistics
BYTES
MCFRAMES
DSDRPDFRMS
USDRPDFRMS
USFRAMES
DSFRAMES
USBYTES
DSBYTES
USMCFRAMES
DSMCFRAMES
G-240W-B (
ONTL2UNI statistics
FRAMES
ONT
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
1)
Note
(1)
A 5 second polling window limitation exists on the ONT, therefore the margin of error for each
15-min window is 5 seconds
Table 1-12 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES,
PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics
RXBLOCKS
RXFRAGS
LOSTFRAGS
✓
✓
✓
✓
✓
BADGEMHDRS
TXFRAGS
G-240W-B (1)
PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES,
PONONTTCFLOW, PONONTTCVOIP statistics
TXBLOCKS
ONT
Note
(1)
A 5 second polling window limitation exists on the ONT, therefore the margin of error for each
15-min window is 5 seconds
Table 1-13 Package P ONTs PONONTTC aggregate performance monitoring statistics
RXBLOCKS
RXFRAGS
LOSTFRAGS
✓
✓
✓
✓
✓
BADGEMHDRS
TXFRAGS
G-240W-B (1)
PONONTTC (aggregate) statistics
TXBLOCKS
ONT
Note
(1)
1-10
A 5 second polling window limitation exists on the ONT, therefore the margin of error for each
15-min window is 5 seconds
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
1.9
G-240W-B functional blocks
G-240W-B indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi)
service. Wi-Fi service on these ONTs is compliant with the IEEE 802.11 standard
and enabled or disabled using a WLAN button. In addition to the Wi-Fi service, these
ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two
RJ-11 POTS ports. These ONTs also feature fiber optic, USB, and power connectors.
Figure 1-3 shows the functional blocks for G-240W-B indoor ONT.
Figure 1-3 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF
video
ANT
PCIe
11n
PA/LNA
converter
USB3.0
GPON
PCIe
GPON SoC
NAND
USB2.0
DDR3
GE GE GE GE
mux
2xRJ11 FXS
RGMII
GE
11ac
3x3
2.4G
ANT
PA/LNA
4x4, 5G
SLIC
GE PHY
RAM
XFMR
4xGE
24674
ONT SoC technology serves as the main hardware block for these ONTs; see
Figure 1-4.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
1-11
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Figure 1-4 G-240W-B ONT hardware block
POTS ports
Control
processor
SoC
DSP
SoC Bridge
Ethernet
MACs
GPON
MAC
Ethernet ports
GPON
19421
ONT SoC technology consists of five key elements:
• GPON MAC
•
•
•
•
The Gigabit Passive Optical Network Media Access Control (GPON MAC)
element on the SoC terminates the GPON interface using an optical diplexer. This
interface supports GPON as described in G.984.3 (GPON TC Layer) ITU
specification.
Ethernet MAC
The SoC provides up to four GE MACs.
DSP interface
The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines
with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and
shares a 32 kbyte data cache with the Control Processor. It provides up to 4
network processor cores, each at 800MHz.
Control Processor
The Control Processor features an integral memory management unit that
supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data
cache with the DSP. The Control Processor and DSP also include a single channel
Data Management Application (DMA) controller with a 4 kbyte read ahead
low-latency Dynamic Random Access Memory (DRAM) access port. The
processors typically run at 500 MHz.
Switch matrix
The Switch matrix provides an integrated data channel between the four GE
MACs, the GPON MAC, the DSP, the control processor, and the other integrated
elements such as flash memory, DRAM, and the local bus controller.
These ONTs can also interact with additional hardware components to support
functionality not provided by the SoC technology.
1-12
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
1.10
G-240W-B standards compliance
G-240W-B indoor ONTs are compliant with the following standards:
•
•
•
•
•
•
•
•
•
802.1p marking and VLAN based pbit is supported
G.711 support for FAX and modem connection
G.984 support GPON interface (framing)
G.984.2 support for Amd1, class B+
G.984.3 support for activation and password functions
G.984.3 support for AES with operator enable/disable on per port-ID level
G.984.3 support for FEC in both upstream and downstream directions
G.984.3 support for multicast using a single GEM Port-ID for all video traffic
G984.4 and G.983.2 support for OMCI v1 and v2 interface for ONT management
and provisioning
FCC statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to provide
a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provided with antenna installation instructions and consider
removing the no-collocation statement.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
1-13
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
this device may not cause harmful interference, and
this device must accept any interference received, including interference that
may cause undesired operation.
Caution — Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate the equipment.
Les changements ou modifications non expressément
approuvés par la partie responsable de la conformité pourraient
annuler l'autoritéde l'utilisateur àutiliser l'équipement.
1.11
G-240W-B special considerations
G-240W-B is a package P ONT.
Wi-Fi service
G-240W-B indoor ONTs feature Wi-Fi service as well as voice and data services.
Wi-Fi is a wireless networking technology that uses radio waves to provide wireless
HSI and network connections. This ONT complies with the IEEE 802.11 standards,
which the Wi-Fi Alliance defines as the basis for Wi-Fi technology.
Wi-Fi physical features
G-240W-B indoor ONTs have the following physical features that assist in providing
Wi-Fi service:
• WLAN button for enabling and disabling Wi-Fi service
• two internal antennae
• two Wi-Fi Protected Setup (WPS) push buttons (one each for 2.4G and 5G) for
adding WPS-enabled wireless devices
Wi-Fi standards and certifications
The Wi-Fi service on G-240W-B indoor ONTs supports the following IEEE
standards and Wi-Fi Alliance certifications:
•
•
•
•
compliant with IEEE 802.11 standards
certified for IEEE 802.11b/g/n standards
WPA support including WPA-PSK
certified for WPA2-Personal and WPA2-Enterprise
Wi-Fi GUI features
G-240W-B indoor ONTs have HTML-based Wi-Fi configuration GUIs.
G-240W-B ONT considerations and limitations
Table 1-14 lists the considerations and limitations for Package P G-240W-B ONTs.
1-14
Alcatel-Lucent 7368 ISAM ONT
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
1 — G-240W-B unit data sheet
Table 1-14 G-240W-B ONT considerations and limitations
Considerations and limitations
Call History Data collection (ONTCALLHST) is supported, except for the following parameters: RTP
packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip
delay, MOS, average jitter, number of jitter-buffer over-runs and under runs.
Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way
Calling, and Call Transfer.
The following voice features / GSIP parameters are configurable on a per-Client/ per-ONT basis (not
per-Subscriber):
•
•
•
•
•
•
Enable Caller ID and Enable Caller Name ID
Digitmap and the associated Interdigit and Critical timers and Enter key parameters
Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT
and must have a lower value than the Permanent time
Miscellaneous timers: Permanent, Timed-release, Reanswer, Error-tone, and CW-alert timers
Features / functions: Message waiting mode, WMWI refresh interval, DTMF volume level
Service Codes for the following features: CCW, Call Hold and Warmline
The Molex interface is not operational.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
1-15
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
2—
Install a G-240W-B indoor ONT
2.1 Purpose
2-2
2.2 General
2-2
2.3 Prerequisites
2-2
2.4 Recommended tools
2.5 Safety information
2.6 Procedure
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
2-2
2-3
2-4
2-1
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
2 — Install a G-240W-B indoor ONT
2.1
Purpose
This chapter provides the steps to install a G-240W-B indoor ONT.
2.2
General
The steps listed in this chapter describe mounting and cabling for G-240W-B indoor
ONTs.
2.3
Prerequisites
You need the following items before beginning the installation:
• all required cables
2.4
Recommended tools
You need the following tools for the installation:
•
•
•
•
•
•
•
•
•
2-2
#2 Phillips screwdriver
1/4 in. (6 mm) flat blade screwdriver
wire strippers
fiber optic splicing tools
RJ-45 cable plug crimp tool
voltmeter or multimeter
optical power meter
drill and drill bits
paper clip
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
2 — Install a G-240W-B indoor ONT
2.5
Safety information
Read the following safety information before installing the unit.
Danger 1 — Hazardous electrical voltages and currents can cause
serious physical harm or death. Always use insulated tools and follow
proper safety precautions when connecting or disconnecting power
circuits.
Tensions et courants électriques dangereuses peuvent
causer des dommages ou la mort physique grave. Toujours utiliser
des outils isolés et suivre les précautions de sécuritéadéquates pour
connecter ou déconnecter les circuits de puissance.
Danger 2 — Make sure all sources of power are turned off and have
no live voltages present on feed lines or terminals. Use a voltmeter to
measure for voltage before proceeding.
Assurez-vous que toutes les sources d'alimentation sont
éteints et ne ont pas de tensions vivants présents sur les lignes
d'alimentation ou de terminaux. Utilisez un voltmètre pour mesurer
la tension avant de procéder.
Danger 3 — Always contact the local utility company before
connecting the enclosure to the utilities.
Toujours contacter la compagnie d'électricité
locale avant de brancher l'enceinte pour les services publics.
Warning — This equipment is ESD sensitive. Proper ESD
protections should be used when removing the fiber access cover of
the indoor ONT.
Cet équipement est sensible ESD. Protections ESD
appropriées doivent être utilisées pour retirer le couvercle de l'ONT
àl'intérieur d'accès en fibre.
Caution — Keep indoor ONTs out of direct sunlight. Prolonged
exposure to direct sunlight can damage the unit.
Gardez ONT intérieur hors du soleil direct. Une
exposition prolongée aux rayons du soleil peut endommager
l'appareil.
Note 1 — Observe the local and national laws and regulations
that may be applicable to this installation.
Respecter les lois et réglementations locales et
nationales qui peuvent être applicables àcette installation.
Note 2 — Observe the following:
• The indoor ONT should be installed in accordance with the
applicable requirements of the NEC or CEC. Local authorities and
practices take precedent when there is conflict between the local
standard and the NEC or CEC.
• The indoor ONT must be installed by qualified service personnel.
• Indoor ONTs must be installed with cables that are suitably rated
and listed for indoor use.
• See the detailed specifications in the G-240W-B unit data sheet for
the temperature ranges for these ONTs.
Respectez les consignes suivantes:
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
• L'ONT intérieure doit être installée en conformitéavec les
exigences applicables de la NEC ou CEC. Les autorités et les
pratiques locales prennent précédent quand il ya conflit entre la
norme locale et le NEC ou CEC.
• L'ONT intérieure doit être installépar un personnel qualifié.
• ONT intérieure doit être installée avec des câbles qui sont
convenablement évalués et classés pour une utilisation intérieure.
• Voir les spécifications détaillées dans la fiche de données de
l'unitéG-240W-B pour les plages de température pour ces ONT.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
2-3
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
2 — Install a G-240W-B indoor ONT
2.6
Procedure
Use this procedure to install a G-240W-B indoor ONT.
Place the indoor ONT unit:
On the flat surface, such as a desk; go to step 3.
Note — The G-240W-B cannot be stacked with another ONT or with
other equipment. The ONT mounting requirements are:
•
•
•
allow a minimum 100 mm clearance above the top cover
allow a minimum 50 mm clearance from the side vents
do not place any heat source directly above the top cover or below
the bottom cover
Le G-240W-B ne peut être empilé avec un autre ONT ou
avec d'autres équipements. Les exigences de montage ONT sont:
• Laisser un espace minimum de 100 mm au-dessus du capot
supérieur
• Laisser un espace minimum de 50 mm à partir des prises d'air
latérales
• Ne placez pas une source de chaleur directement au-dessus du
capot supérieur ou inférieur à la couverture inférieure
On a wall, go to step 2.
Mount the G-240W-B indoor ONT on a wall.
The G-240W-B indoor ONT can be mounted in either a horizontal or vertical
position, as shown in Figure 2-1. If possible, mount the ONT on a wall stud.
Figure 2-1 Wall mounting keyholes on G-240W-B indoor ONTs
Keyholes for horizontal mounting
RES ET
Keyholes for
vertical
mounting
24111
ii
Mark the wall with the location of the mounting holes. These holes should be
the same distance apart as the distance between the centers of the keyholes
on the ONT.
iii
Drill the two holes in the wall where the ONT will be mounted and then drive
the mounting screws into the holes.
The recommended length of mounting screw is 1.15 in. (3.8 cm).
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
2 — Install a G-240W-B indoor ONT
Do not drive the screw into the wall completely. Leave approximately 1/8 in.
(6 mm) between the screw head and the wall surface.
iv
Slide the wall mount keyholes on the ONT enclosure or fiber storage tray
down over the mounting screws until the ONT is securely seated.
Review the connection locations as shown in Figures 2-2.
Figure 2-2 G-240W-B indoor ONT connections (back view)
Wireless
On/Off
button
USB 3.0
USB 2.0
USB
ports
TEL1
TEL2
POTS
ports (2)
(RJ-11)
LAN1
LAN2
LAN3
LAN4
POWER
ON/OFF
UPS
Ethernet
Reset
On/Off
ports (4)
button
button
Power
(RJ-45) Wi-Fi
input
security
buttons (2)
Fiber
optic
port
24614
Connect the Ethernet cables to the RJ-45 ports; see Figure 2-2 for the location of
the RJ-45 ports.
Route the POTS cables directly to the RJ-11 ports as per local practices.
The POTS port to the left is labeled 1 for Line 1 while the port on the right is
labeled 2 for Line 2, as shown in Figure 2-2.
Connect the fiber optic cable with SC/APC adapter into the SC/APC connector; see
Figure 2-2 for the location of the SC/APC connector.
Danger — Fiber cables transmit invisible laser light. To avoid eye
damage or blindness, never look directly into fibers, connectors, or
adapters.
Câbles de fibres transmettent la lumière laser invisible.
Pour éviter des lésions oculaires ou la cécité, ne jamais regarder
directement dans les fibres, les connecteurs ou adaptateurs.
Warning — Be careful to maintain a bend radius of no less than 1.5 in.
(3.8 cm) when connecting the fiber optic cable. Too small of a bend
radius in the cable can result in damage to the optic fiber.
Veillez à maintenir un rayon de courbure d'au moins 1,5
po. (3,8 cm) lors de la connexion du câble de fibre optique. Trop petit
d'un rayon de courbure dans le câble peut entraîner des dommages à
la fibre optique.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
2 — Install a G-240W-B indoor ONT
Note — Fiber cable preparation varies depending on the type and size
of the inside or outside plant fiber cable being spliced to the SC/APC
fiber optic pigtail cable.
Préparation du câble de fibres varie en fonction du type et de
la taille de l'intérieur ou de câble de fibres de plante extérieur étant
assemblés bord à bord pour la SC/APC câble en queue de cochon à
fibres optiques.
Install the power supply according to manufacturer specifications.
Note — Observe the following:
•
Units must be powered by a Listed or CE approved and marked
limited power source power supply with a minimum output rate of
12 V dc, 1.25 A.
Respectez les onsignes
suivantes:
• Les unités doivent être alimentés par une alimentation de source
d'alimentation limitée répertoriés ou homologués CE et sont
marqués d'un taux de sortie minimum de 12 V cc, 1,25 A
Connect the power cable to the power connector.
Power up the ONT unit by using the power switch.
10
If used, enable the Wi-Fi service.
Locate the WLAN button on the ONT; see Figure 2-2 for location of the WLAN
button.
ii
Press the WLAN button to change the status of the Wi-Fi service.
11
Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368
Hardware and Cabling Installation Guide.
12
Activate and test the services; see the 7368 Hardware and Cabling Installation
Guide.
13
If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management,
and Troubleshooting Guide.
14
If necessary, reset the ONT.
15
Locate the Reset button on a G-240W-B indoor ONT as shown in Figure 2-2.
ii
Insert the end of a straightened paper clip or other narrow object into the
hole in the Reset button to reset the ONT.
STOP. This procedure is complete.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
3—
Replace a G-240W-B indoor ONT
3.1 Purpose
3-2
3.2 General
3-2
3.3 Prerequisites
3-2
3.4 Recommended tools
3.5 Safety information
3.6 Procedure
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
3-2
3-3
3-4
3-1
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
3 — Replace a G-240W-B indoor ONT
3.1
Purpose
This chapter provides the steps to replace G-240W-B indoor ONTs.
3.2
General
The steps listed in this chapter describe mounting and cabling for G-240W-B indoor
ONTs.
3.3
Prerequisites
You need the following items before beginning the installation:
• all required cables
3.4
Recommended tools
You need the following tools for replacing the ONT:
•
•
•
•
•
•
•
•
3-2
#2 Phillips screwdriver
1/4 in. (6 mm) flat blade screwdriver
wire strippers
fiber optic splicing tools
RJ-45 cable plug crimp tool
voltmeter or multimeter
optical power meter
drill and drill bits
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
3 — Replace a G-240W-B indoor ONT
3.5
Safety information
Read the following safety information before replacing the unit.
Danger 1 — Hazardous electrical voltages and currents can cause
serious physical harm or death. Always use insulated tools and follow
proper safety precautions when connecting or disconnecting power
circuits.
Tensions et courants électriques dangereuses peuvent
causer des dommages ou la mort physique grave. Toujours utiliser
des outils isolés et suivre les précautions de sécuritéadéquates pour
connecter ou déconnecter les circuits de puissance.
Danger 2 — Make sure all sources of power are turned off and have
no live voltages present on feed lines or terminals. Use a voltmeter to
measure for voltage before proceeding.
Assurez-vous que toutes les sources d'alimentation
sont éteints et ne ont pas de tensions vivants présents sur les lignes
d'alimentation ou de terminaux. Utilisez un voltmètre pour mesurer
la tension avant de procéder.
Danger 3 — Always contact the local utility company before
connecting the enclosure to the utilities.
Toujours contacter la compagnie d'électricité
locale avant de brancher l'enceinte pour les services publics.
Warning — This equipment is ESD sensitive. Proper ESD
protections should be used when removing the fiber access cover of
the indoor ONT.
Cet équipement est sensible ESD. Protections ESD
appropriées doivent être utilisées pour retirer le couvercle de l'ONT
àl'intérieur d'accès en fibre
Caution — Keep indoor ONTs out of direct sunlight. Prolonged
exposure to direct sunlight can damage the unit.
Gardez ONT intérieur hors du soleil direct. Une
exposition prolongée aux rayons du soleil peut endommager
l'appareil.
Note 1 — Observe the local and national laws and regulations
that may be applicable to this installation.
Respecter les lois et réglementations locales et
nationales qui peuvent être applicables àcette installation
Note 2 — Observe the following:
• The indoor ONT should be installed in accordance with the
applicable requirements of the NEC or CEC. Local authorities and
practices take precedent when there is conflict between the local
standard and the NEC or CEC.
• The indoor ONT must be installed by qualified service personnel.
• Indoor ONTs must be installed with cables that are suitably rated
and listed for indoor use.
• See the detailed specifications in the G-240W-B unit data sheet for
the ONT temperature ranges for these ONTs.
Respectez les consignes suivantes:
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
• L'ONT intérieure doit être installée en conformitéavec les
exigences applicables de la NEC ou CEC. Les autorités et les
pratiques locales prennent précédent quand il ya conflit entre la
norme locale et le NEC ou CEC.
• L'ONT intérieure doit être installépar un personnel qualifié.
• ONT intérieure doit être installée avec des câbles qui sont
convenablement évalués et classés pour une utilisation intérieure.
• Voir les spécifications détaillées dans la fiche de données de
l'unitéG-240W-B pour les plages de température pour ces ONT
ONT.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
3-3
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
3 — Replace a G-240W-B indoor ONT
3.6
Procedure
Use this procedure to replace a G-240W-B indoor ONT.
Deactivate the ONT services at the P-OLT.
If you are using the SLID feature, this step is not required. The ONT and the
services can remain in service (IS).
Use the RTRV-ONT command to verify the ONT status and th associated
services. Record the serial number or the SLID of the ONT displayed in the
command output.
Example:
RTRV-ONT::ONT-1-1-1-1-1;
ii
If the ONT is in service, place the ONT in OOS state.
Example:
ED-ONT::ONT-1-1-1-1-1;
If used, disable the Wi-Fi service by pressing the WLAN button; see Figure 3-1 for
the location of the WLAN button.
Figure 3-1 G-240W-B indoor ONT connections
Wireless
On/Off
button
USB 3.0
USB 2.0
USB
ports
TEL1
TEL2
POTS
ports (2)
(RJ-11)
LAN1
LAN2
LAN3
LAN4
POWER
ON/OFF
UPS
Ethernet
Reset
On/Off
ports (4)
button
button
Power
(RJ-45) Wi-Fi
input
security
buttons (2)
Fiber
optic
port
24614
3-4
Power down the unit by using the on/off power switch.
Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 3-1 for
the connector locations on the G-240W-B indoor ONT.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
3 — Replace a G-240W-B indoor ONT
Disconnect the fiber optic cables.
Danger — Fiber cables transmit invisible laser light. To avoid eye
damage or blindness, never look directly into fibers, connectors, or
adapters.
Câbles de fibres transmettent la lumière laser invisible.
Pour éviter des lésions oculaires ou la cécité, ne jamais regarder
directement dans les fibres, connecteurs ou adaptateurs
Unplug the fiber optic cable with SC/APC connector from the ONT; see
Figure 3-1 for the location of the fiber optic port.
ii
Attach a fiber dust cover to the end of the SC/APC connector.
Replace the ONT with a new unit:
On a flat surface, such as a desk, substitute the new ONT for the old ONT on
a flat surface, horizontally resting on its four feet.
On a wall.
Slide the old ONT off of the mounting screws until the ONT is free of the
wall.
ii
Slide the wall mount holes on the ONT enclosure over the mounting
screws until it is securely seated.
Connect the Ethernet cables directly to the RJ-45 ports; see Figure 3-1 for the
location of the RJ-45 ports.
Connect the POTS cables directly to the RJ-11 ports as per local practices; see
Figure 3-1 for the location of the RJ-11 ports.
The RJ-11 port to the left is labeled 1 for Line 1 while the port on the right is
labeled 2 for Line 2.
If required, have approved service personnel who are trained to work with optic
fiber clean the fiber optic connection. See the 7368 ISAM ONT Configuration,
Management, and Troubleshooting Guide for more information about fiber optic
handling, inspection, and cleaning.
Danger — Fiber optic cables transmit invisible laser light. To avoid eye
damage or blindness, never look directly into fibers, connectors, or
adapters.
Câbles de fibre optique transmettent la lumière laser
invisible. Pour éviter des lésions oculaires ou la cécité, ne jamais
regarder directement dans les fibres, les connecteurs ou adaptateurs.
10
Connect the fiber optic cable with SC/APC adapter into the SC/APC connector.
Figure 3-1shows the location of the SC/APC connector.
Danger — Fiber cables transmit invisible laser light. To avoid eye
damage or blindness, never look directly into fibers, connectors, or
adapters.
Câbles de fibre optique transmettent la lumière laser
invisible. Pour éviter des lésions oculaires ou la cécité, ne jamais
regarder directement dans les fibres, les connecteurs ou adaptateurs.
Warning — Be careful to maintain a bend radius of no less than 1.5 in.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
(3.8 cm) when connecting the fiber optic cable. Too small of a bend
radius in the cable can result in damage to the optic fiber.
Veillez à maintenir un rayon de courbure d'au moins 1,5
po. (3,8 cm) lors de la connexion du câble de fibre optique. Trop petit
d'un rayon de courbure dans le câble peut entraîner des dommages à
la fibre optique.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
3-5
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
3 — Replace a G-240W-B indoor ONT
Note — Fiber cable preparation varies depending on the type and size
of the inside or outside plant fiber cable being spliced to the SC/APC
fiber optic pigtail cable.
Préparation du câble de fibres varie en fonction du type et
de la taille de l'intérieur ou de câble de fibres de plante extérieur
étant assemblés bord à bord pour la SC/APC câble en queue de cochon
à fibres optiques.
11
Install the power supply according to manufacturer specifications.
Note — Observe the following:
•
Units must be powered by a Listed or CE approved and marked
limited power source power supply with a minimum output rate of
12 V dc, 1.25 A.
Respectez les consignes suivantes:
• Les unités doivent être alimentés par une alimentation de
source d'alimentation limitée répertoriés ou homologués
CE et sont marqués d'un taux de sortie minimum de 12 V
cc, 1,25 A.
12
Connect the power cable to the power connector.
13
Power up the unit by using the power switch.
14
If used, enable the Wi-Fi service by pressing the WLAN button; see Figure 3-1 for
the location of the WLAN button.
15
If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management,
and Troubleshooting Guide for more information.
Note — A new SLID or the old SLID may be used with the replacement
ONT. If a new SLID is used, the new SLID must also be programmed at
the P-OLT using TL1 or a network manager. If the old SLID is used, no
changes need to be made at the P-OLT; see the operations and
maintenance documentation for the OLT for more details.
Une nouvelle EDTR ou le vieux EDTR peut être utilisé avec
l'ONT de remplacement. Si une nouvelle EDTR est utilisé, le nouveau
EDTR doit également être programmé à la classe P-OLT utilisant TL1
un gestionnaire de réseau. Si l'ancien EDTR est utilisé, aucune
modification ne est à apporter à la classe P-OLT; voir les opérations et
la documentation de maintenance pour le BTA pour plus de détails.
16
Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368
Hardware and Cabling Installation Guide.
17
Activate and test the services; see the 7368 Hardware and Cabling Installation
Guide.
18
If necessary, reset the ONT.
19
Locate the Reset button on a G-240W-B indoor ONT as shown in Figure 3-1.
ii
Insert the end of a straightened paper clip or other narrow object into the
hole in the Reset button to reset the ONT.
STOP. This procedure is complete.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4—
Configure a G-240W-B indoor ONT
4.1 General
4-2
4.2 HGU mode GUI configuration
4-2
4.3 SFU mode GUI configuration
4-39
4.4 Operator ID
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-44
4-1
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
4.1
General
Please refer to the configuration information provided with your OLT for the
software configuration procedure for a G-240W-B ONT.
For HTTP configuration procedures, please refer to the 7368 ISAM ONT
Configuration, Management, and Troubleshooting Guide.
4.2
HGU mode GUI configuration
Use the procedures below to use the web-based GUI for the G-240W-B in HGU
mode. This mode is preset at delivery.
A home gateway unit (HGU) is a home networking device, used as a gateway to
connect devices in the home through fiber to the Internet. An HGU provides a variety
of features for the home network including routing and firewall capability. By using
the HGU, users can connect all smart equipment in their home, including personal
computers, set-top boxes, mobile phones, and other consumer electronics devices, to
the Internet.
Login
Use the procedure below to login to the web-based GUI for the G-240W-B.
Procedure 4-1 Login to web-based GUI
Open a web browser and enter the IP address of the ONT in the address bar.
The login window appears.
The default gateway IP address is http://192.168.1.1. You can connect to this IP
address using your web browser after connecting your PC to one of Ethernet ports
of the ONT. The static IP address of your PC must be in the same subnet as the
ONT.
Enter your username and password in the Log in window, as shown in Figure 4-1.
The default username and password are printed on the ONT. The default user
name is userAdmin. The default superuser name is adminGPON. Contact
Alcatel-Lucent for the superuser password.
4-2
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Figure 4-1 Web login window
Caution — If you reset the router to recover the default username and
password, all other router configuration settings will also be restored to
their factory default values.
Si vous réinitialisez le routeur pour récupérer le nom
d'utilisateur et mot de passe par défaut, tous les autres paramètres de
configuration du routeur seront aussi restaurés à leurs valeurs par
défaut d'usine.
Note — If you forget the current username and password, press the
reset button for 5 s and the default values for the username and
password will be recovered at startup.
Si vous oubliez le nom d'utilisateur et mot de passe actuel,
appuyez sur le bouton de réinitialisation pendant 5 s et les valeurs
par défaut pour le nom d'utilisateur et mot de passe seront
récupérés au démarrage.
Click Login.
STOP. This procedure is complete.
Device and connection status
G-240W-B ONTs support the retrieval of a variety of device and connection
information, including:
•
•
•
•
•
•
device information
LAN status
WAN status
WAN status IPv6
Home networking information
Optics module status
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-2 Device information retrieval
Select Status > Device Information from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-2.
Figure 4-2 Device Information window
Table 4-1 describes the fields in the Device Information window.
Table 4-1 Device Information parameters
4-4
Field
Description
Device Name
Name on the ONT
Vendor
Name of the vendor
Serial Number
Serial number of the ONT
Hardware version
Hardware version of the ONT
Boot version
Boot version of the ONT
Software version
Software version of the ONT
Chipset
Chipset of the ONT
Device Running
Time
Amount of time the device has run since last reset in hours, minutes, and
seconds
Click Refresh to update the displayed information.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-3 LAN status retrieval
Select Status > LAN Status from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-3.
Figure 4-3 LAN status window
Table 4-2 describes the fields in the LAN status window.
Table 4-2 LAN status parameters
Field
Description
Wireless Information
Wireless Status
Indicates whether the wireless is on or off
Wireless Channel
Wireless channel number
SSID Name
Name of each SSID
Wireless
Encryption Status
Encryption type used on the wireless connection
Wireless Rx
Packets
Number of packets received on the wireless connection
Wireless Tx
Packets
Number of packets transmitted on the wireless connection
Wireless Rx Bytes
Number of bytes received on the wireless connection
Wireless Tx Bytes
Number of bytes transmitted on the wireless connection
Power
Transmission (mW)
Power of the wireless transmission, in mW
Ethernet Information
Ethernet Status
Indicates whether the Ethernet connection is on or off
Ethernet IP
Address
IP address of the Ethernet connection
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-5
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Ethernet Subnet
Mask
Subnet Mask of the Ethernet connection
Ethernet MAC
Address
MAC address of the Ethernet connection
Ethernet Rx
Packets
Number of packets received on the Ethernet connection
Ethernet Tx
Packets
Number of packets transmitted on the Ethernet connection
Ethernet Rx Bytes
Number of bytes received on the Ethernet connection
Ethernet Tx Bytes
Number of bytes transmitted on the Ethernet connection
(2 of 2)
Click Refresh to update the displayed information.
STOP. This procedure is complete.
Procedure 4-4 WAN status retrieval
Select Status > WAN Status from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-4.
Figure 4-4 WAN status window
Table 4-3 describes the fields in the WAN status window.
4-6
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Table 4-3 WAN status parameters
Field
Description
WAN connection
list
Drop-down menu listing all WAN connections. The connection shown is the
connection for which WAN status will be shown.
Connection Mode
Connection mode of the WAN connection
Enable/Disable
Select this checkbox to enable the WAN connection
VLAN
VLAN ID
WAN Link Status
Whether the WAN link is up or down
Pon Link Status
Whether the PON link is up or down
Tx Packets
Number of packets transmitted on the WAN connection
Rx Packets
Number of packets received on the WAN connection
Tx Dropped
Number of packets dropped on the transmit WAN connection
Rx Dropped
Number of packets dropped on the receive WAN connection
Err Packets
Number of errored packets on the WAN connection
Click Refresh to update the displayed information.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-7
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-5 WAN status IPv6 retrieval
Select Status > WAN Status IPv6 from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-5.
Figure 4-5 WAN status IPv6 window
Table 4-4 describes the fields in the WAN status IPv6 window.
Table 4-4 WAN status IPv6 parameters
Field
Description
WAN connection
list
Drop-down menu listing all WAN connections. The connection shown is the
connection for which WAN status will be shown.
Connection Mode
Connection mode of the WAN connection
Enable/Disable
Select this checkbox to enable the WAN connection
VLAN
VLAN ID
WAN Link Status
Whether the WAN link is up or down
IPv6 Address
IPv6 address that identifies the device and its location
Netmask
Network mask
Gateway
Gateway address
Primary DNS
Primary Domain Name Server
Second DNS
Secondary Domain Name Server
Pon Link Status
Whether the PON link is up or down
(1 of 2)
4-8
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Tx Packets
Number of packets transmitted on the WAN connection
Rx Packets
Number of packets received on the WAN connection
Tx Dropped
Number of packets dropped on the transmit WAN connection
Rx Dropped
Number of packets dropped on the receive WAN connection
Err Packets
Number of errored packets on the WAN connection
(2 of 2)
Click Refresh to update the displayed information.
STOP. This procedure is complete.
Procedure 4-6 Home networking information retrieval
Select Status > Home Networking from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-6.
Figure 4-6 Home networking information window
Table 4-5 describes the fields in the Home networking window.
Table 4-5 Home networking parameters
Field
Description
Local Interface
Ethernet
Table displays the number of Ethernet connections and their settings
Wireless
Table displays the number of wireless connections and their settings
Wireless Settings
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-9
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Network Name
Name of the wireless network
Access Point
Hexadecimal address of the wireless access point
Local Devices
Table entry
Each entry indicates the connection type, device name, IP address, hardware
address, and IP address allocation of each connected local device.
(2 of 2)
Click Delete to delete a particular local device connection.
Click Refresh to update the displayed information.
STOP. This procedure is complete.
Procedure 4-7 Optics module status retrieval
Select Status > Optics Module Status from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-7.
Figure 4-7 Optics module status window
Table 4-6 describes the fields in the Optics module status window.
Table 4-6 Optics module status parameters
Field
Description
Laser Bias Current (ONT ANI-ONT-Side Optical
Measurements)
Laser bias current, measured in uA
Optics Module Voltage (ONT ANI-ONT-Side Optical
Measurements)
Optics module voltage, measured in V
(1 of 2)
4-10
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Optics Module Temperature (ONT ANI-ONT-Side
Optical Measurements)
Optics module temperature, measured in
Rx Optics Signal Level at 1490 nm (ONT ANI-ONT-Side
Optical Measurements)
Received optics signal level at 1490 nm,
measured in dBm
Tx Optics Signal Level at 1310 nm (ONT ANI-ONT-Side
Optical Measurements)
Transmitted optics signal level at 1310 nm,
measured in dBm
Lower (ONT ANI-ONT-Side Optical
Measurements-Optical Threshold)
Lower optical threshold, measured in dBm
Upper (ONT ANI-ONT-Side Optical
Measurements-Optical Threshold)
Lower optical threshold, measured in dBm
(2 of 2)
Click Refresh to update the displayed information.
STOP. This procedure is complete.
Network configuration
G-240W-B ONTs also support network configuration, including:
•
•
•
•
•
•
•
•
LAN
LAN IPv6
WAN
WiFi 2.4G
WiFi 5G
Routing
DNS
TR-069
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-11
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-8 LAN networking configuration
Select Network > LAN from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-8.
Figure 4-8 LAN network window
Table 4-7 describes the fields in the LAN network window.
Table 4-7 LAN network parameters
4-12
Field
Description
Port Mode:
All Port to L2 Mode
Select this checkbox to set all ports to L2 mode
Port Mode
Port 1 - 4
Drop-down port mode for each port: Route mode or bridge mode
IPv4 Address
IP Address of the ONT
Subnet Mask
Subnet mask of the ONT
DHCP enable
Select this checkbox to enable DHCP
DHCP Start IP
Address
Starting DHCP IP address
DHCP End IP
Address
Ending DHCP IP address
DHCP Lease Time
DHCP lease time (in min)
Bind MAC Address
MAC address to associate to the LAN
Bind IP Address
IP address to associate to the bound MAC address
Select the mode for each port.
Click Save.
Enter the DHCP configuration information.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Click Save.
Bind a MAC address to the LAN by entering the MAC and IP addresses and then
clicking Add. Repeat for all MAC addresses to be bound.
STOP. This procedure is complete.
Procedure 4-9 LAN IPv6 networking configuration
Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-9.
Figure 4-9 LAN IPv6 network window
Table 4-8 describes the fields in the LAN IPv6 network window.
Table 4-8 LAN IPv6 network parameters
Field
Description
DNS Server
Choose a DNS server from the drop-down menu.
prefix config
Choose a prefix config option from the drop-down menu, either
WANConnection (prefix will be obtained from the WAN) or Static (enables you
to enter the prefix).
prefix
This field appears if you selected the “Static” option for the “prefix config”
field. Type a connection.
Interface
This field appears if you selected the Wan Connection option for the “prefix
config” field. Choose a WAN connection interface from the drop-down menu.
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-13
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
DHCPv6 Server
Enable
Select this checkbox to enable DHCP IPv6 server.
DHCP Start IP
Address
Enter the starting DHCP IP address.
DHCP End IP
Address
Enter the ending DHCP IP address.
Whether the
address info
through DCHP
Select this checkbox to enable address information retrieval through DHCP.
Whether other info
obtained through
DHCP
Select this checkbox to enable retrieval of other information through DHCP.
Maximum interval
for periodic RA
messages
Enter the maximum interval (in seconds) for periodic Router Advertisement
messages. The interval range is from 4 to 1800.
Minimum interval
for periodic RA
messages
Enter the minimum interval (in seconds) for periodic Router Advertisement
messages. The interval range is from 4 to 1800.
(2 of 2)
4-14
Choose a DNS server, prefix config, and interface.
Select or enter the DHCP configuration information.
Enter the maximum and minimum intervals for RA messages.
Click Save/Apply.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-10 WAN networking configuration
Select Network > WAN from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-10.
Figure 4-10 WAN network window
Table 4-9 describes the fields in the WAN network window.
Table 4-9 WAN network parameters
Field
Description
WAN Connection
List
Choose a WAN connection from the drop-down menu to set the connection
parameters
Connection Type
Select a connection type: IPoE or PPPoE
IP Mode
Choose an IP mode from the drop-down menu: IPv4 or IPv6
Enable/Disable
Select this checkbox to enable the WAN connection
NAT
Select this checkbox to enable NAT
Service
Select the checkboxes to enable service types for this connection
Enable VLAN
Select this checkbox to enable VLAN
VLAN ID
Enter the VLAN ID
VLAN PRI
Enter the VLAN PRI
WAN IP Mode
Choose an IP mode from the drop-down menu
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-15
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Connection Type
Choose a connection type from the drop-down menu
Username
Enter the username
Password
Enter the password
Keep Alive Time
Enter the Keep Alive Time (from 5 to 60 seconds)
(2 of 2)
Configure a specific WAN connection.
Click Save.
STOP. This procedure is complete.
Procedure 4-11 WiFi 2.4G networking configuration
Select Network > WiFi 2.4G from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-11.
Figure 4-11 WiFi 2.4G network window
Table 4-10 describes the fields in the WiFi 2.4G network window.
4-16
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Table 4-10 WiFi 2.4G network parameters
Field
Description
Enable
Select this checkbox to enable WiFi
Mode
Choose a wi-fi mode from the drop-down menu:
•
•
•
•
•
auto (b/g/n)
b/g
Channel
Choose a channel from the drop-down menu or choose Auto to have the
channel automatically assigned
Bandwidth
Choose 20 MHz or 40 MHz from the drop-down menu.
Transmitting
Power
Choose the percentage transmitting power from the drop-down menu
SSID Select
Choose the SSID from the drop-down menu
SSID Name
Enter the SSID name
Enable SSID
Enable or disable SSID from this drop-down menu
SSID Broadcast
Enable or disable SSID broadcast from this drop-down menu
Port Mode
Choose a port mode from the drop-down menu:
•
•
Encrypt Mode
WPA Version
Route
Bridge
Choose an encryption mode from the drop-down menu:
•
•
•
•
OPEN
WEP
WPA/WPA2 Personal
WPA/WPA2 Enterprise
Choose a WPA version from the drop-down menu:
•
•
•
WPA1
WPA2
WPA1/WPA2
WPA Encryption
Mode
Choose a WPA encryption mode from the drop-down menu:
WPA Key
Enter the WPA key
Enable WPS
Enable or disable WPS from this drop-down menu
•
•
•
TKIP
AES
TKIP/AES
Configure the WiFi connection.
If you have enabled and configured WPS, click WPS connect.
Click Save.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-17
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-12 WiFi 5G networking configuration
Select Network > WiFi 5G from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-12.
Figure 4-12 WiFi 5G network window
Table 4-11 describes the fields in the WiFi 5G network window.
Table 4-11 WiFi 5G network parameters
Field
Description
Enable
Select this checkbox to enable WiFi
Channel
Choose a channel from the drop-down menu or choose Auto to have the
channel automatically assigned
Bandwidth
Choose 20 MHz or 40 MHz from the drop-down menu
Transmitting
Power
Choose the percentage transmitting power from the drop-down menu
SSID Select
Choose the SSID from the drop-down menu
SSID Name
Enter the SSID name
Enable SSID
Enable or disable SSID from this drop-down menu
SSID Broadcast
Enable or disable SSID broadcast from this drop-down menu
(1 of 2)
4-18
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Encrypt Mode
Choose an encryption mode from the drop-down menu:
•
•
•
•
OPEN
WEP
WPA/WPA2 Personal
WPA/WPA2 Enterprise
WPA Key
Enter the WPA key
Enable WPS
Enable or disable WPS from this drop-down menu
(2 of 2)
Configure the WiFi connection.
If you have enabled and configured WPS, click WPS connect.
Click Save.
STOP. This procedure is complete.
Procedure 4-13 Routing configuration
Select Network > Routing from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-13.
Figure 4-13 Routing network window
Table 4-12 describes the fields in the Routing network window.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-19
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Table 4-12 Routing network parameters
Field
Description
Enable Routing
Select this checkbox to enable routing
Destination IP
Address
Enter the destination IP address
Destination
Netmask
Enter the destination network mask
Gateway
Enter the gateway address
IPv4 Interface
Choose a WAN connection previously created in the WAN network window
from the drop-down menu
Enter the routing information.
Click Add.
STOP. This procedure is complete.
Procedure 4-14 DNS configuration
Select Network > DNS from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-14.
Figure 4-14 DNS network window
Table 4-13 describes the fields in the DNS network window.
4-20
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Table 4-13 DNS network parameters
Field
Description
Domain Name
Domain name
IPv4 Address
Domain IP address
Origin Domain
Origin domain name
New Domain
New domain name
Enter the domain name and IP address and click Add.
If required, associate an origin domain with a new domain, click Add.
STOP. This procedure is complete.
Procedure 4-15 TR-069 configuration
Select Network > TR-069 from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-15.
Figure 4-15 TR-069 network window
Table 4-14 describes the fields in the TR-069 network window.
Table 4-14 TR-069 network parameters
Field
Description
Periodic Inform
Enable
Select this checkbox to enable periodic inform updates
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-21
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Periodic Inform
Interval(s)
Time between periodic inform updates, in seconds
URL
URL of the auto-configuration server
Username
Username used to log in to the ONT
Password
Password used to log in to the ONT
Connect Request
Username
Username used to log in to the auto-configuration server
Connect Request
Password
Password used to log in to the auto-configuration server
(2 of 2)
Configure TR-069 by entering the required information.
Click Save.
STOP. This procedure is complete.
Security configuration
G-240W-B ONT also supports security configuration, including:
•
•
•
•
4-22
firewall
MAC filter
IP filter
DMZ and ALG
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-16 Firewall configuration
Select Security > Firewall from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-16.
Figure 4-16 Firewall window
Table 4-15 describes the fields in the firewall window.
Table 4-15 Firewall parameters
Field
Description
Security level
Choose the security level from the drop-down menu
Attack Protect
Enable or disable attack protect from the drop-down menu
Configure the firewall.
Click Save.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-23
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-17 MAC filter configuration
Select Security > Mac Filter from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-17.
Figure 4-17 MAC filter window
Table 4-16 describes the fields in the MAC filter window.
Table 4-16 MAC filter parameters
4-24
Field
Description
Enable MAC filter
Select this checkbox to enable the MAC filter
Mac Address
MAC address
Mac Filter Mode
Choose the MAC filter mode from this drop-down menu
Configure a MAC filter.
Click Add.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-18 IP filter configuration
Select Security > IP filter from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-18.
Figure 4-18 IP filter window
Table 4-17 describes the fields in the IP filter window.
Table 4-17 IP filter parameters
Field
Description
Enable IP Filter
Select this checkbox to enable an IP filter
Mode
Choose an IP filter mode from the drop-down menu:
•
•
Internal Client
Drop for upstream
Drop for downstream
Choose an internal client from the drop-down menu:
•
•
Customer setting - uses the IP address input below
IP - uses the connecting devices' IP to the ONT
Local IP Address
Local IP address
Source Subnet
Mask
Source subnet mask
Remote IP Address
Remote IP address
Destination Subnet
Mask
Destination subnet mask
Protocol
Choose an application protocol or all from the drop-down menu
Configure the IP filter.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-25
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Click Add.
STOP. This procedure is complete.
Procedure 4-19 DMZ and ALG configuration
Select Security > DMZ and ALG from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-19.
Figure 4-19 DMZ and ALG window
Table 4-18 describes the fields in the DMZ and ALG window.
Table 4-18 DMZ and ALG parameters
Field
Description
ALG Config
Select the checkboxes to enable the protocols to be supported by the ALG
DMZ Config
4-26
WAN Connection
List
Choose a WAN connection from the drop-down menu
Enable DMZ
Select this checkbox to enable DMZ on the chosen WAN connection
DMZ IP Address
Choose Customer Setting and enter the DMZ IP address or choose the IP
address of a connected device from the drop-down menu
Configure ALG.
Click Save ALG.
Configure DMZ.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Click Save DMZ.
STOP. This procedure is complete.
Application configuration
G-240W-B ONT also supports application configuration, including:
•
•
•
•
port forwarding
DDNS
NTP
USB storage
Procedure 4-20 Port forwarding configuration
Select Application > Port forwarding from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-20.
Figure 4-20 Port forwarding window
Table 4-19 describes the fields in the port forwarding window.
Table 4-19 Port forwarding parameters
Field
Description
APPName
Choose an application name from the drop-down menu
WAN Port
WAN port range
LAN Port
LAN port range
Internal Client
Choose a connected device from the drop-down menu and enter the
associated IP address
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-27
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Protocol
Choose the port forwarding protocol from the drop-down menu:
•
•
•
TCP
UDP
TCP/UDP
Enable Mapping
Select this checkbox to enable mapping
WAN Connection
List
Choose a WAN connection from the drop-down menu
(2 of 2)
Configure port forwarding.
Click Add.
STOP. This procedure is complete.
Procedure 4-21 DDNS configuration
Select Application > DDNS from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-21.
Figure 4-21 DDNS window
Table 4-20 describes the fields in the DDNS window.
Table 4-20 DDNS parameters
Field
Description
WAN Connection
List
Choose a WAN connection from the drop-down menu
(1 of 2)
4-28
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Enable DDNS
Select this checkbox to enable DDNS on the chosen WAN connection
ISP
Choose an ISP from the drop-down menu.
Domain Name
Domain name
Username
Username
Password
Password
(2 of 2)
Configure DDNS.
Click Save.
STOP. This procedure is complete.
Procedure 4-22 NTP configuration
Select Application > NTP from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-22.
Figure 4-22 NTP window
Table 4-21 describes the fields in the NTP window.
Table 4-21 NTP parameters
Field
Description
Enable NTP Service
Select this checkbox to enable NTP service
Current Time
Enter the current local date and time
First Time Server
Choose a time server from the drop-down menu or choose Customer setting
and enter the address of the time server.
(1 of 2)
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-29
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Field
Description
Second Time
Server
Choose a time server from the drop-down menu or choose Customer setting
and enter the address of the time server.
Interval Time
Interval at which to get the time from the time server, in seconds
Time Zone
Choose the local time zone from the drop-down menu
(2 of 2)
Configure NTP.
Click Save.
STOP. This procedure is complete.
Procedure 4-23 USB storage configuration
Select Application > USB storage from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-23.
Figure 4-23 USB storage window
Table 4-22 describes the fields in the USB storage window.
Table 4-22 USB storage parameters
4-30
Field
Description
Enable FTP server
Select this checkbox to enable using an FTP server for data storage
Username
Username for FTP server
Password
Password for FTP server
Re-enter Password
Password for FTP server
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Configure USB storage.
Click Save.
STOP. This procedure is complete.
Maintenance
G-240W-B ONT also supports maintenance tasks, including:
•
•
•
•
•
•
•
•
•
password change
SLID configuration
device management
backup and restore
firmware upgrade
device reboot
restore factory defaults
diagnose
log
Procedure 4-24 Password configuration
Select Maintain > Password from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-24.
Figure 4-24 Password window
Table 4-23 describes the fields in the password window.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-31
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Table 4-23 Password parameters
Field
Description
New Password
New password
Re-enter password
Password must match password entered above
Prompt message
Password prompt message
Configure the new password.
Click Save.
STOP. This procedure is complete.
Procedure 4-25 SLID configuration
Select Maintain > SLID Configuration from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-25.
Figure 4-25 SLID configuration window
Table 4-24 describes the fields in the SLID configuration window.
Table 4-24 SLID configuration parameters
4-32
Field
Description
Current SLID
Displays current SLID
Input new SLID
Enter new SLID
SLID Mode
Choose a SLID mode from the drop-down menu.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Configure the new SLID.
Click Save.
STOP. This procedure is complete.
Procedure 4-26 Device management
Select Maintain > Device Management from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-26.
Figure 4-26 Device management window
Table 4-25 describes the fields in the Device management window.
Table 4-25 Device management parameters
Field
Description
Host name
Choose a host from the drop-down menu
Alias
Enter an alias for the chosen host
Configure an alias for a specific host.
Click Add.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-33
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-27 Backup and restore
Select Maintain > Backup and Restore from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-27.
Figure 4-27 Backup and Restore window
Click Select File and choose the backup file.
Click Import Config File to restore the ONT to the saved backup or click Export
Config File to export the current ONT configuration to the backup file.
STOP. This procedure is complete.
Procedure 4-28 Upgrade firmware
Select Maintain > Firmware Upgrade from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-28.
Figure 4-28 Firmware upgrade window
4-34
Click Select File and choose the firmware file.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Click Upgrade to upgrade the firmware.
STOP. This procedure is complete.
Procedure 4-29 Reboot ONT
Select Maintain > Reboot Device from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-29.
Figure 4-29 Reboot window
Click Reboot to reboot the ONT.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-35
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-30 Restore factory defaults
Select Maintain > Factory Default from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-30.
Figure 4-30 Factory default window
4-36
Click Factory Default to reset the ONT to its factory default settings.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-31 Diagnose connections
Select Maintain > Diagnose from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-31.
Figure 4-31 Diagnose window
Choose a WAN connection to diagnose from the drop-down menu.
Enter the IP address or domain name.
Select the test type by selecting either ping or traceroute.
Enter a ping packet length (64-1024).
Enter the number of ping attempts to perform (1 - 1000).
Click Start Test. Results will be displayed at the bottom of the window.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-37
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-32 View log files
Select Maintain > Log from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-32.
Figure 4-32 Log window
Choose a write level from the drop-down menu to determine which types of events
are recorded in the log file:
•
•
•
•
•
•
•
•
Choose a reading level from the drop-down menu to determine which types of
events to display from the log file:
•
•
•
•
•
•
•
•
4-38
Emergency
Alert
Critical
Error
Warning
Notice
Informational
Debug
Emergency
Alert
Critical
Error
Warning
Notice
Informational
Debug
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
4.3
The log file is displayed at the bottom of the window.
STOP. This procedure is complete.
SFU mode GUI configuration
Use the procedures below to use the web-based GUI for the G-240W-B in SFU
mode. This mode is preset at delivery.
SFU customer premise devices are designed for single indoor residential
applications. These ONTs address the demand for bandwidth intensive services, such
as high definition television (HDTV), video-on-demand (VOD) and online games.
The ONT can be configured to seamlessly deliver voice-over-IP and high speed
Internet access via a single fiber optic connection to the home.
Login
Use the procedure below to login to the web-based GUI for the G-240W-B.
Procedure 4-33 Login to web-based GUI
Open a web browser and enter the IP address of the ONT in the address bar.
The login window appears.
The default gateway IP address is http://192.168.1.254. You can connect to this
IP address using your web browser after connecting your PC to one of Ethernet
ports of the ONT. The static IP address of your PC must be in the same subnet as
the ONT.
Enter your username and password in the Log in window, as shown in Figure 4-33.
The default username and password are printed on the ONT. The default
superuser username is adminGPON. Contact Alcatel-Lucent for the superuser
password.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-39
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Figure 4-33 Web login window
Caution — If you reset the router to recover the default username and
password, all other router configuration settings will also be restored to
their factory default values.
Si vous réinitialisez le routeur pour récupérer le nom
d'utilisateur et mot de passe par défaut, tous les autres paramètres de
configuration du routeur seront aussi restaurés à leurs valeurs par
défaut d'usine.
Note — If you forget the current username and password, press the
reset button for 5 s and the default values for the username and
password will be recovered at startup.
Si vous oubliez le nom d'utilisateur et mot de passe actuel,
appuyez sur le bouton de réinitialisation pendant 5 s et les valeurs
par défaut pour le nom d'utilisateur et mot de passe sera récupéré
au démarrage
Click Login.
STOP. This procedure is complete.
Device and connection status
G-240W-B ONTs support the retrieval of a variety of device information.
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-34 Device information retrieval
Select Status > Device Information from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-34.
Figure 4-34 Device Information window
Table 4-26 describes the fields in the Device Information window.
Table 4-26 Device Information parameters
Field
Description
Device Name
Name on the ONT
Vendor
Name of the vendor
Serial Number
Serial number of the ONT
Hardware version
Hardware version of the ONT
Boot version
Boot version of the ONT
Software version
Software version of the ONT
Chipset
Chipset of the ONT
Device Running
Time
Amount of time the device has run since last reset in hours, minutes, and
seconds
Click Refresh to update the displayed information.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-41
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Maintenance
G-240W-B ONT also supports maintenance tasks, including:
• password change
• LOID configuration
• SLID configuration
Procedure 4-35 Password configuration
Select Maintain > Password from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-35.
Figure 4-35 Password window
Table 4-27 describes the fields in the password window.
Table 4-27 Password parameters
4-42
Field
Description
New Password
New password
Re-enter password
Password must match password entered above
Prompt message
Password prompt message
Configure the new password.
Click Save.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-36 LOID configuration
Select Maintain > LOID Config from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-36.
Figure 4-36 LOID configuration window
Enter the LOID.
Enter the password, if applicable.
Click Save/Apply.
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-43
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-37 SLID configuration
Select Maintain > SLID Configuration from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-37.
Figure 4-37 SLID configuration window
Table 4-28 describes the fields in the SLID configuration window.
Table 4-28 SLID configuration parameters
4.4
Field
Description
Current SLID
Displays current SLID
Input new SLID
Enter new SLID
SLID Mode
Choose a SLID mode from the drop-down menu.
Configure the new SLID.
Click Save.
STOP. This procedure is complete.
Operator ID
Use the procedure below to modify the operator ID for the G-240W-B.
4-44
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
4 — Configure a G-240W-B indoor ONT
Procedure 4-38 Modify the operator ID using OLT
Create a new .xml file named OntConfig.xml.
For AONT releases AONTR2.4.02 and higher, add the following content to the
OntConfig.xml file:



where xxxx is the correct operator ID, such as PTXX.
For AONT releases prior to AONTR2.4.02, add the following content to the
OntConfig.xml file:



where xxxx is the correct operator ID, such as PTXX.
Use a TFTP client tool to transfer OntConfig.xml to the OLT's ONT directory and
change the filename to the software version number, for example,
FE54869201410.xml.
Using TL1 commands, configure ONUSWCTRL:
ENT-ONTSWCTRL::1::::HWVER=hwver,VARNT=,PLNDSWVER=UNPLANNED,
PLNDSWVERCONF=UNPLANNED,DLDSWVER=swver;
where:
hwver is the hardware version number, for example 3FE54945ABBA.
swver is the software version number used as the filename in step 2, for example
3FE54869201410.
Download the .xml file to update the operator ID:
ED-ONT::ONT-1/1/3/1/19::::DLSW=AUTO;
Restart the ONT, then connect to the LAN and access the web-based to check the
operator ID default setting.
Using TL1 commands, disable further downloads:
ED-ONT::ONT-1/1/3/1/19::::DLSW=DISABLED;
STOP. This procedure is complete.
Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240W-B Product Guide
4-45
R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01
Customer documentation and product support
Customer documentation
http://www.alcatel-lucent.com/myaccess
Product manuals and documentation updates are available at
alcatel-lucent.com. If you are a new user and require access to this
service, please contact your Alcatel-Lucent sales representative.
Technical Support
http://support.alcatel-lucent.com
Documentation feedback
documentation.feedback@alcatel-lucent.com
R05.01.01 I December 2014 I 3FE-56678-AAAA-TCZZA I Edition 01
.Lucent
2014
A1catel-Lucent. A11 rights
served.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Alcatel-Lucent
Create Date                     : 2015:01:08 12:09:42+08:00
Modify Date                     : 2015:03:05 16:06:16+08:00
Subject                         : 7368 ISAM G-240W-B
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Alcatel-Lucent
Description                     : 7368 ISAM G-240W-B
Title                           : 7368 ISAM ONT G-240W-B Product Guide
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2015:03:05 16:06:16+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:6137337e-ddcb-4056-b6da-6b17429ddfea
Instance ID                     : uuid:394912c8-9f69-4371-9da0-2bed17c8b3bb
Page Count                      : 113

EXIF Metadata provided by EXIF.tools