Nokia Solutions and Networks WTFA-01 GSM 800 Transciever User Manual dn99252966x3x0xen

Nokia Solutions and Networks GSM 800 Transciever dn99252966x3x0xen

Solution Accessories

Download: Nokia Solutions and Networks WTFA-01 GSM 800 Transciever User Manual dn99252966x3x0xen
Mirror Download [FCC.gov]Nokia Solutions and Networks WTFA-01 GSM 800 Transciever User Manual dn99252966x3x0xen
Document ID303291
Application IDi6We2RE5/xcB5trwspeO6A==
Document DescriptionSolution Accessories
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize80.1kB (1001296 bits)
Date Submitted2003-02-17 00:00:00
Date Available2003-02-14 00:00:00
Creation Date2002-10-10 17:14:02
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2002-10-10 17:09:30
Document Titledn99252966x3x0xen
Document CreatorFrameMaker 5.5.6.

Nokia MetroSite EDGE Base Station
Solution Accessories
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
1 (66)
Solution Accessories
The information in this documentation is subject to change without notice and describes only
the product defined in the introduction of this documentation. This documentation is intended
for the use of Nokia's customers only for the purposes of the agreement under which the
documentation is submitted, and no part of it may be reproduced or transmitted in any form or
means without the prior written permission of Nokia. The documentation has been prepared to
be used by professional and properly trained personnel, and the customer assumes full
responsibility when using it. Nokia welcomes customer comments as part of the process of
continuous development and improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity,
or performance of the mentioned hardware or software products cannot be considered binding
but shall be defined in the agreement made between Nokia and the customer. However, Nokia
has made all reasonable efforts to ensure that the instructions contained in the documentation
are adequate and free of material errors and omissions. Nokia will, if necessary, explain issues
which may not be covered by the documentation.
Nokia's liability for any errors in the documentation is limited to the documentary correction of
errors. NOKIA WILL NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS IN THIS
DOCUMENTATION OR FOR ANY DAMAGES, INCIDENTAL OR CONSEQUENTIAL
(INCLUDING MONETARY LOSSES), that might arise from the use of this documentation or
the information in it.
This documentation and the product it describes are considered protected by copyright
according to the applicable laws.
NOKIA logo is a registered trademark of Nokia Corporation.
Other product names mentioned in this documentation may be trademarks of their respective
companies, and they are mentioned for identification purposes only.
Copyright © Nokia Corporation 2002. All rights reserved.
2 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
0523
FCC
Hereby, Nokia Corporation, declares that this product is in compliance with the
essential requirements and other relevant provisions of Directive: 1999/5/EC.
The product is marked with the CE marking and Notified Body number according to the
Directive 1999/5/EC.
FCC §15.21 - Information to user - This product is used as an intentional radiated
equipment and any changes or modifications on the equipment without any approval
by Nokia could void the user's authority to operate the equipment.
FCC §15.105 - Information to user - This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
DN99252966
Issue 3-0 en
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
3 (66)
Solution Accessories
4 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Contents
Contents 5
List of tables 7
List of figures 9
Summary of changes 11
About this document 13
2.1
2.1.1
2.1.2
2.2
2.2.1
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.6
2.5
2.6
2.6.1
2.6.2
2.6.3
2.6.4
2.7
2.7.1
2.7.2
2.7.3
2.7.4
2.7.5
2.8
2.8.1
2.8.2
2.8.3
2.8.4
2.8.5
Accessories and specifications 15
Flexbus accessories 15
Flexbus cable specifications 15
TNC male connector specifications (straight and right-angled) 17
Local Management Port accessories 20
Q1 LMP cable specifications 20
Abis PCM cable 21
PCM cable 75 ohm 22
PCM cable 120 ohm 22
BT43 plug 23
TQ plug 23
MetroSite antennas 23
MetroSite 130o panel antenna 24
MetroSite XX-pol panel antenna 26
Omni dual band antenna 31
Indoor omni multi-band antenna 34
Indoor multi-band panel antenna 35
Pole mounting clamps (50-115 mm pole diameter) 37
GSM/EDGE 900, 1800 and 1900 combiners 38
Antenna lines 42
Antenna line cables 42
N male connector: straight 45
N male connector: right angled 46
7-16 Straight Male connector 48
MetroSite Battery Backup Unit 49
Battery Backup Unit 49
Mains power cable (230 VAC) 49
230/110 VAC output cable 50
Alarm cable 51
Battery connection kit 52
Miscellaneous 53
Jumper cables 54
Grounding cable 54
AC power cables for MetroSite BTS or MetroHub 55
DC power cable for MetroSite BTS or MetroHub 56
Optical Alignment Tool 57
Attachments 59
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
5 (66)
Solution Accessories
6 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
List of tables
Table 1.
Flexbus accessories for the MetroSite EDGE Base Station
Table 2.
Flexbus cable specifications
Table 3.
LMP accessories for the MetroSite EDGE Base Station
Table 4.
LMP cable connector specifications
Table 5.
Abis PCM cable and accessories
Table 6.
PCM cable 75 Ω specifications
Table 7.
PCM cable 120 Ω specifications
Table 8.
Antennas for the Nokia MetroSite EDGE Base Station
Table 9.
Specifications for the 130o antenna
15
17
20
20
21
22
22
23
25
Table 10. Specifications for the MetroSite XX-pol 900/1800 MHz panel antenna
27
Table 11. Specifications for the MetroSite XX-pol 850/1900 MHz panel antenna
30
Table 12. Specifications for the omni-directional 900/1800 MHz dual band
antenna 31
Table 13. Specifications for the omni-directional 850/1900 MHz dual band
antenna 33
Table 14. Specifications for the indoor omni multi-band antenna
35
Table 15. Specifications for the indoor multi-band panel antenna
36
Table 16. Combiners for the Nokia MetroSite EDGE Base Station
Table 17. Specifications for the GSM/EDGE combiners
38
40
Table 18. Antenna line accessories for the Nokia MetroSite EDGE Base
Station 42
Table 19. Sheath characteristics for the antenna line cable
Table 20. Cable characteristics for the antenna line cable
43
43
Table 21. Attenuation and power characteristics for the antenna line cable
Table 22. Specifications for the N male connector
46
Table 23. Specifications for the N male connector, right angled
47
Table 24. Specifications for the N male connector, right angled
48
Table 25. Specifications for the 230 VAC mains power cable
50
Table 26. Specifications for the 230/110 VAC mains power cable
Table 27. Specifications for the alarm cable
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
44
51
52
Draft
7 (66)
Solution Accessories
Table 28. Contents of the battery connection kit
52
Table 29. Miscellaneous accessories for the Nokia MetroSite EDGE Base
Station 53
Table 30. Jumper cable accessories
54
Table 31. Grounding cable specifications
54
Table 32. Specifications for the 230 VAC power cable
55
Table 33. Specifications for the 110 VAC power cable
56
Table 34. Specifications for the DC power cable
56
Table 35. Specifications for the optical alignment tool
8 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
58
DN99252966
Issue 3-0 en
List of figures
Figure 1.
Flexbus cable 16
Figure 2.
TNC connectors 19
Figure 3.
LMP cable and connectors 21
Figure 4.
MetroSite 130o panel antenna 25
Figure 5.
MetroSite XX-pol 900/1800 MHz panel antenna 27
Figure 6.
MetroSite XX-pol 850/1900 MHz panel antenna 29
Figure 7.
Omni-directional dual band 900/1800 MHz antenna 31
Figure 8.
Omni-directional dual band 850/1900 MHz antenna 33
Figure 9.
Indoor omni multi-band antenna 34
Figure 10. Indoor multi-band panel antenna 36
Figure 11. Installing the indoor multi-band panel antenna 37
Figure 12. Antenna pole mounting clamp 38
Figure 13. GSM/EDGE combiner 39
Figure 14. Dimensions of the GSM/EDGE combiner 40
Figure 15. Antenna line cable 43
Figure 16. N male connector 45
Figure 17. N male connector, right angled 47
Figure 18. 7-16 Straight male connector 48
Figure 19. Battery connection kit 53
Figure 20. Optical alignment tool 57
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
9 (66)
Solution Accessories
10 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Summary of changes
Version 1-0, 5th March, 1999. Norman M. Thomas.
Version 2-0, 30th August 2001. Tyrone Williams.
Version 3-0, August 2002. Kudos (Celia Pires, Mark Seymour). Added chaining
extension cables into “Miscellaneous”, made corrections to specifications
following comments from Jan Ekman, Tomi Karvonen and Peter Berghall.
Version 3-0, October 2002. Kudos (Mark Seymour). Product codes updated.
800/1900 MHz antennas added.
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
11 (66)
Solution Accessories
12 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
About this document
About this document
This document lists the Nokia accessories which are available to support the
Nokia MetroSiteTM Base Station. Descriptions and specifications of the
accessories are also included.
For more information and ordering of the accessories, contact your local Nokia
customer services representative.
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
13 (66)
Solution Accessories
14 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Accessories and specifications
2.1
Flexbus accessories
Table 1.
2.1.1
Flexbus accessories for the MetroSite EDGE Base Station
Item
Product code
Jumper cable, 2.5 m, TNC (m) - TNC (f)
CS72450.10
RG223, 4 m, TNC-TNC straight
T36625.02
RG223, 8 m, TNC-TNC straight
T36625.03
RG223, 15 m, TNC-TNC straight
T36625.04
TNC male for flexbus cable straight
(RG214)
T36630.01
TNC male for flexbus cable 90 degree
(RG214)
T36631.01
TNC male for flexbus cable straight
(RG223)
T36627.01
TNC male for flexbus cable 90 degree
(RG223)
T36627.02
Flexbus cable, RG223, 500 m reel
T36626.01
Flexbus cable, RG214, 500 m reel
T36629.01
Flexbus cable specifications
Product codes: T36626.01 (RG223); T36629.01 (RG214)
This coaxial cable is suitable for both straight and right-angled BNC/TNC plug
connector types. Flexbus uses 50 Ω cable with TNC male connectors of both
types, as applicable.
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
15 (66)
Solution Accessories
The cable is capable of handling frequencies up to 2.8 GHz and is, for example,
used to connect the radio outdoor unit to the transmission unit.
Table 2 and Figure 1 identify the diameter of the cable attributes. The 'D' and 'E'
min-max ranges allow for the different connectors used.
Cables, type RG223, of 4 m, 8 m and 15 m lengths terminated with TNC male
straight connectors are available. The product code for each of these is identified
in Table 1.
Figure 1.
16 (66)
Flexbus cable
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Table 2.
Parameter
Flexbus cable specifications
RG214 cable
G223 cable
Detail
Inner Conductor
Dielectric Core
Outer conductor
(layer 1)
2.28 mm diameter
0.9 mm diameter
Silver plated copper wires (7)
Silver plated copper wire (single)
5.6 Ω/km at 20oC
29.4 Ω/km at 20oC
50+/- 2 Ω impedance
50+/- 2 Ω impedance
101 nf/km capacitance at 800 Hz
106 nf/km capacitance at 800 Hz
201 g/m weight
59 g/m weight
Attenuation: 23 dB/100 m at 800 MHz.
Attenuation: 69 dB/100 m at 1000 MHz
Specification: DIN 40500/T4
Specification: DIN 40500/T4
7.4 mm diameter
3.05 mm diameter
PE
PE
Colour: neutral
Colour: neutral
Braided shield, silver plated copper
wires
Braided shield, silver plated copper wires
Specification: DIN 40500/T4
Specification: DIN 40500/T4
Outer conductor
(layer 2)
9.1 mm diameter maximum
4.39 mm diameter maximum
Braided shield, silver plated copper
wires
Braided shield, copper plated wires
Specification: DIN 40500/T4
Specification: DIN 40500/T4
Sheath
2.1.2
10.9 mm diameter
5.55 -0.2 mm diameter
PVC
PVC
Black
Black
Specification: DIN 53505
Specification: DIN 53505
TNC male connector specifications (straight and right-angled)
Product code: T36630.01 and T36631.01 (RG214); T36627.01 and T36627.02
(RG223)
RF one step TNC connectors are single piece assemblies for the centre conductor
and the braid of a broad range of coaxial cables. The connectors are fully
compliant with MIL-C-39012 connectors. In this case, 50 Ω versions are used.
The features of these connectors include:
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
17 (66)
Solution Accessories
•
exceptional cable retention force to withstand vibration and frequent
connections and disconnections
•
long term reliability
•
usable with RG/U and Raychem Cheminax cables
•
meets performance requirements of MIL-C-39012 up to 2.8 GHz
Only the right-angled connectors are used with type RG214 cable because of the
cable's rigidity.
18 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Figure 2.
DN99252966
Issue 3-0 en
TNC connectors
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
19 (66)
Solution Accessories
2.2
Local Management Port accessories
Table 3.
2.2.1
LMP accessories for the MetroSite EDGE Base Station
Item
Product code
Nokia Q1 LMP cable
T55270.01
Q1 LMP cable specifications
Product code: T55270.01
This is an RS232 cable terminated with a BQ bayonet type connector at one end
and a 9-pin `D' type (D9F) connector at the other end. The length of the cable is
2,5 m and is provided already assembled.
Table 4.
LMP cable connector specifications
BQ Connector
‘D’ type Connector
Pin No.
Function
Pin No.
Function
LMP in
TD
n/c
1, 4, 6-9
n/c
LMP out
RD
GND
GND
RD = Received Data
TD = Transmitted Data
GND = Ground
n/c = not connected
Note
The pins of each connector correlate as shown in Table 4. For example, pin 1 of
connector BQ connects to pin 3 of the ‘D’ type connector.
20 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
BQ on the BTS end
of cable
D9P (female) on the PC
end of cable
3 LMP out
2 LMP in
4 GND
2 nc
= Hole
= Pin
Figure 3.
2.3
nc
RD
TD
nc
GND
nc
nc
nc
nc
GND = Ground
RD = Received data
TD = Transmitted data
nc = not connected
LMP cable and connectors
Abis PCM cable
Table 5.
DN99252966
Issue 3-0 en
Abis PCM cable and accessories
Item
Product code
Abis PCM cable for MetroSite, 3 m, 120 Ω
T36612.01
Abis PCM cable for MetroSite, 15 m, 120
Ω
T36612.05
Abis PCM cable for MetroSite, 50 m, 120
Ω
T36612.04
Abis PCM cable, 75 Ω/m
T36602.01
Abis PCM cable, 120 Ω/m
T36614.01
BT43 plug, 75 Ω, 6 pieces for ABC cable
T36601.01
TQ plug, 120 Ω, 1 piece
CS73214.02
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
21 (66)
Solution Accessories
2.3.1
PCM cable 75 ohm
Product Code: T36602.01
The 75 Ω PCM cable is used for 2 Mbit transmission between the Nokia
MetroSite EDGE Base Station and a BSC. This high quality coaxial cable
consists of a plain copper inner conductor, polyethylene dielectric material, two
copper braids, and a PVC outer jacket.
Table 6.
2.3.2
PCM cable 75 Ω specifications
Characteristic impedance
75+ / - 4 Ω
Mutual capacitance
67 pF/m
Wave attenuation 1 MHz
2.3 dB/100 m
Wave attenuation 4 MHz
4.5 dB/100 m
Wave attenuation 20 MHz
9.2 dB/100 m
Operating voltage
300 V rms
Minimum bending radius
18 mm
Diameter
3.55 mm
Colour
Black
PCM cable 120 ohm
Product Code: T36614.01
The 120 Ω PCM cable is used for 2 Mbit transmission between the Nokia
MetroSite EDGE Base Station and a BSC. This high quality cable consists of four
bare copper wires, polyethylene wire insulation, intermediate plastic tape
insulation, tinned copper wire gauze, and a halogen-free outer sheath.
The cables available are 3 m, 15 m, and 50 m, terminated with a TQ plug at each
end.
Table 7.
22 (66)
PCM cable 120 Ω specifications
Characteristic impedance
120+ / - 10 Ω
Mutual capacitance
40 nF/km
Wave attenuation 1 MHz
1.7 dB/100 m
Wave attenuation 4 MHz
3.5 dB/100 m
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Table 7.
2.3.3
PCM cable 120 Ω specifications (Continued)
Wave attenuation 20 MHz
7.8 dB/100 m
Operating voltage
300 V rms
Minimum bending radius
30 mm
Diameter
4.1 mm
Colour
Grey
BT43 plug
Product code: T36601.01
This connector is used with the TZC5024 cable. For connection of this plug to the
Abis 75 Ω coaxial cable, refer to Attachment 1.
2.3.4
TQ plug
Product code: CS73214.02
This Abis 120 Ω interface connector supports the use of cables with outer
diameter of 4-13 mm and wires of dimension AWG 26-30.
For connection of this plug to the Abis 120 Ω cable refer to Attachment 2. The
cable is provided already assembled and is 2 m in length.
2.4
MetroSite antennas
Table 8.
Antennas for the Nokia MetroSite EDGE Base Station
Item
Product code
MetroSite 130o panel antenna, dual band
870-960 / 1710-1880 MHz, 5 dBi, 2 x N
female connectors
CS72454.01
MetroSite XX-pol panel antenna, dual
CS72180
band 870-960 / 1710-1880 MHz, 65o,
12.5/13.5 dBi, 4 port
MetroSite XX-pol panel antenna, dual
band 824-960 / 1710-2170 MHz,
14.5/17.5 dBi
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
CS72763.01
65o,
Draft
23 (66)
Solution Accessories
Table 8.
Antennas for the Nokia MetroSite EDGE Base Station (Continued)
Item
Product code
MetroSite omni antenna, dual band 870960 / 1710-1880 MHz, 2 dBi, 2 x N female
connectors
CS72187
MetroSite omni antenna, dual band 824960 / 1805-2170 MHz, 2 dBi, N female
CS72187.02
Indoor omni antenna, multi-band 824-960
CS72166
/ 1425-2170 MHz, 2 dBi,
360o
, N female
Indoor panel antenna, multi-band 824-960
/ 1425-2170 MHz, 7 dBi,
90o,
N female
Single pole mounting clamp for 50-115
mm poles
2.4.1
CS72168
CS72196
MetroSite 130o panel antenna
Product code: CS72454.01
This antenna is a vertically polarised, dual band, two-port antenna providing 130o
coverage with a gain of 6 dBi.
24 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Figure 4.
MetroSite 130o panel antenna
Table 9.
Specifications for the 130o antenna
Item
GSM 900
GSM 1800
Frequency range
870-960 MHz
1710-1880 MHz
VSWR
< 1:1.7
< 1:1.7
Gain
6 dBi
6 dBi
Impedance
50 Ω
50 Ω
Polarization
Vertical
Vertical
Front-to-back ratio (copolar)
> 10 dB
> 10 dB
Half power beam width
Horizontal: 130o
Horizontal: 130o
Vertical: 55o
Vertical: 55o
50 W
50 W
Maximum power/input (at
25o
DN99252966
Issue 3-0 en
C)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
25 (66)
Solution Accessories
Table 9.
2.4.2
Specifications for the 130o antenna (Continued)
Item
GSM 900
GSM 1800
Isolation
> 25 dB (GSM 900 - GSM 900) on Tx band > 30 dB
(GSM 1800 - GSM 1800) > 30 dB (GSM 900 - GSM
1800)
Input
2 x N female
Connector position
Bottom
Weight
2.0 kg (without packaging)
Wind load
Frontal: 27 N (at 150 km/h) Lateral: 16 N (at 150 km/h)
Rear side: 63 N (at 150 km/h)
Maximum wind velocity
150 km/h
Packing size
480 x 125 x 110 mm
Height x width x depth
452 x 95 x 100 mm
Material
Reflector screen: painted aluminium Radome: ABS;
grey NCS S 2500-N screws and nuts: stainless steel
Mounting
TBA
Ice protection
The antenna remains operational during icy conditions
Grounding
The metal parts of the antenna, including the mounting
kit are DC grounded.
MetroSite XX-pol panel antenna
Product codes: CS72180, CS72763.01
This is a four port, dual band antenna. Its output is cross polarised + / - 45 o and
provides 65 o coverage with a gain of 12.5 to 13.5 dBi for the 900/1800 MHz
antenna and 14.5 to 17.5 dBi for the 850/1900 MHz antenna (see also the note
below).
Note
Further variations of the Nokia MetroSite XX-pol panel 850/1900 MHz antennas
are available. Please contact your Nokia representative.
26 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
900/1800 MHz XX-pol panel antenna (CS72180)
DN99252966
Issue 3-0 en
Figure 5.
MetroSite XX-pol 900/1800 MHz panel antenna
Table 10.
Specifications for the MetroSite XX-pol 900/1800 MHz panel
antenna
Item
GSM 900
GSM 1800
Frequency range
870-960 MHz
1710-1880 MHz
VSWR
< 1.5
< 1.5
Impedance
50 Ω
50 Ω
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
27 (66)
Solution Accessories
Table 10.
Specifications for the MetroSite XX-pol 900/1800 MHz panel
antenna (Continued)
Item
GSM 900
GSM 1800
Polarization
+45o ; -45o
+45o ; -45o
Front-to-back ratio (copolar)
> 30 dB
> 30 dB
Half power beam width
+45o / -45o
+45o / -45o
Horizontal: 65o
Horizontal: 65o
Vertical: 28o
Vertical: 28o
250 W
150 W
Maximum power/input (at
50o C)
Isolation
> 30 dB (GSM 900 - GSM 900) > 30 dB (GSM 1800 GSM 1800) > 30 dB (GSM 900 - GSM 1800)
Input
4 x 7-16 female
Connector position
Top or bottom
Weight
7 kg
Wind load (at 150 km/h)
Frontal: 110 N. Lateral: 60 N. Rearside: 240 N.
Maximum wind velocity
200 km/h
Packing size
782 x 287 x 165 mm
Height / width / depth
656 mm / 262 mm / 116 mm
Material
Reflector screen: weather proof aluminium Radome:
fibreglass (white)
Screws and nuts: stainless steel
Mounting
Walls: using two mounting plates already attached to
the antenna
Masts: using two clamps suitable for the mast diameter
28 (66)
Ice protection
The antenna remains operational under icy conditions
Grounding
The metal parts of the antenna, including the mounting
kit and the inner conductors are DC grounded.
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
850/1900 MHz XX-pol panel antenna (CS72763.01)
Figure 6.
DN99252966
Issue 3-0 en
MetroSite XX-pol 850/1900 MHz panel antenna
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
29 (66)
Solution Accessories
Table 11.
Specifications for the MetroSite XX-pol 850/1900 MHz panel
antenna
Item
GSM 850
GSM 1900
Frequency range
824-960 MHz
1710-2170 MHz
VSWR
< 1.5
< 1.5
Impedance
50 Ω
50 Ω
Polarization
+45o ; -45o
+45o ; -45o
Front-to-back ratio (copolar)
> 28 dB
> 25 dB
Half power beam width
+45o / -45o
+45o / -45o
Horizontal: 68 - 65o
Horizontal: 65 - 63o
Vertical: 16 - 14.5o
Vertical: 7.5 - 6.5o
250 W
200 W
Maximum power/input (at
50o C)
Isolation: intrasystem
> 30 dB
Isolation: intersystem
> 45 dB
Input
4 x 7-16 female
Connector position
Top or bottom
Weight
16.5 kg
Wind load (at 150 km/h)
Frontal: 230 N. Lateral: 180 N. Rearside: 430 N.
Maximum wind velocity
200 km/h
Packing size
1590 x 287 x 177 mm
Height / width / depth
1296 mm / 262 mm / 139 mm
Material
Reflector screen: weather proof aluminium Radome:
fibreglass (white)
Screws and nuts: stainless steel
Mounting
Walls: using two mounting plates already attached to
the antenna
Masts: using two clamps suitable for the mast diameter
30 (66)
Ice protection
The antenna remains operational under icy conditions
Grounding
The metal parts of the antenna, including the mounting
kit and the inner conductors are DC grounded. The
inputs 824-960 MHz are also DC grounded. The inputs
1710-2170 MHz are coupled capacitively.
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
2.4.3
Omni dual band antenna
Product codes: CS72187, CS72187.02
This is a dual port, dual band 900/1800 or 850/1900 MHz antenna. The output is
omni-directional (360o) with a gain of 2 dBi and has two units (upper and lower).
900/1800 MHz omni-directional, dual band antenna (CS72187)
DN99252966
Issue 3-0 en
Figure 7.
Omni-directional dual band 900/1800 MHz antenna
Table 12.
Specifications for the omni-directional 900/1800 MHz dual band
antenna
Input
2 x N female
Frequency range
870-960 MHz and 1710-1880 MHz for the upper
and lower units
VSWR
< 1.8
Gain
2 dBi
Impedance
50 Ω
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
31 (66)
Solution Accessories
Table 12.
Specifications for the omni-directional 900/1800 MHz dual band
antenna (Continued)
Polarization
Vertical
Isolation
> 25 dB
Maximum power/input
50 W at 50oC ambient temperature
Weight
1.2 kg
Radome diameter
30 mm
Wind load
30 N at 150 km/h
Maximum wind load
200 km/h
Packing size
700 x 80 x 80 mm (approximately)
Height
500 mm
Material
Radiator: copper, brass
Radome: fibreglass (grey)
Base: weatherproof aluminium
Mounting clamp and screws: stainless steel
32 (66)
Mounting
Attached laterally at the tip of a tubular mast of
40-70 mm diameter. The connecting cable (not
supplied) runs outside the mast.
Range of application
Urban areas, preferably in places around
buildings at low or medium heights above ground
level or light poles or short masts on rooftops.
The antenna shape reduces the optical impact.
Grounding
All metal parts of the antenna and the mounting
kit (excluding the inner conductor of the upper
unit) are DC grounded.
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
850/1900 MHz omni-directional, dual band antenna (CS72187.02)
DN99252966
Issue 3-0 en
Figure 8.
Omni-directional dual band 850/1900 MHz antenna
Table 13.
Specifications for the omni-directional 850/1900 MHz dual band
antenna
Input
2 x N female
Frequency range
824-960 MHz and 1805-2170 MHz for the upper
and lower units
VSWR
< 2.0
Gain
2 dBi
Impedance
50 Ω
Polarization
Vertical
Maximum power/input
50 W at 50oC ambient temperature
Weight
250 g
Radome diameter
20 mm
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
33 (66)
Solution Accessories
Table 13.
Specifications for the omni-directional 850/1900 MHz dual band
antenna (Continued)
Height
216 mm
Material
Radiator: brass
Radome: fibreglass (white)
Base: weatherproof aluminium
Mounting clamp and screws: stainless steel
2.4.4
Mounting
One hole mounting (16 mm) to surfaces of
maximum 10 mm thickness or attached laterally
at the tip of a tubular mast of 40-70 mm diameter.
Range of application
Urban areas, preferably in places around
buildings at low or medium heights above ground
level or light poles or short masts on rooftops.
The antenna shape reduces the optical impact.
Grounding
All metal parts of the antenna and the mounting
kit (excluding the inner conductor of the upper
unit) are DC grounded.
Indoor omni multi-band antenna
Product code: CS72166
This is a single port, multi-band 850/900/1800/1900 MHz antenna. This antenna
is vertically polarised and the horizontal radiation pattern is omni-directional
(360o) with a gain of 2 dBi. The antenna can be operated in all frequency ranges
simultaneously, and needs no additional groundplane.
Figure 9.
34 (66)
Indoor omni multi-band antenna
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Table 14.
Specifications for the indoor omni multi-band antenna
Input
N female
Frequency range
824-960 MHz and 1425-2170 MHz
VSWR
< 2.0: 824-960MHz
< 2.0: 1425-1710MHz
< 1.6: 1710-1990MHz
< 2.0: 1990-2170MHz
Gain
2 dBi
Input
1 x N female
Impedance
50 Ω
Polarization
Vertical
Maximum power (at 50o C)
50 W /band
Weight
400 g
Diameter
260 mm
Height
78 mm (without connector)
Material
Base: aluminium
Protective housing: high impact
polystyrol
Colour: white
Additional painting is possible
2.4.5
Mounting
Three holes in the base to enable
mounting on a ceiling. Two types of
screws are supplied. N connector: a hole
of 35 mm diameter needed in the ceiling.
Grounding
All metal parts including the inner
conductor are DC grounded.
Indoor multi-band panel antenna
Product code: CS72168
This is a single port, multi-band indoor panel antenna. The antenna has a half
power beam width of 90 o with a gain of 7 dBi.
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
35 (66)
Solution Accessories
Figure 10.
Indoor multi-band panel antenna
Table 15.
Specifications for the indoor multi-band panel antenna
Input
Cable RG 223/CU of 1 m length; white; N
female connector.
Frequency range
824-960 MHz and 1710-2170 MHz
VSWR
870-960 MHz and 1710-1900 MHz: < 1.6
824-960 MHz and 1710-2170 MHz: < 2.0
Gain
7 dBi approximately
Impedance
50 Ω
Polarization
Vertical
Half power beam width
Horizontal; 90o
Maximum power (at 50o C)
25 W
Weight
500 g
Packing size
321 x 165 x 50 mm
Height x width x depth
205 x 155 x 42 mm
Material
Radiator: brass
Reflector: Aluminium
Radome: ABS (white)
Mounting plates: stainless steel
36 (66)
Mounting
Two holes of 6 mm diameter in the
mounting plate.
Grounding
All metal parts and inner conductor DC
grounded.
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Installing the multi-band indoor panel antenna
1.
Fix the attachment plate to the wall using two 4 mm diameter screws. See
[1] in Figure 11.
2.
Align the antenna over the attachment plate, keeping the cable in the
middle of the plate. See [2] in Figure 11.
3.
Pull the antenna downwards until it clicks into place. See [3] in Figure 11.
Do not pull the antenna downwards with the antenna cable.
Figure 11.
2.4.6
Installing the indoor multi-band panel antenna
Pole mounting clamps (50-115 mm pole diameter)
Product code: CS72196
This standard single unit clamp is suitable for standard Nokia antennas.
The number of clamps required depends upon the antenna.
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
37 (66)
Solution Accessories
Figure 12.
2.5
Antenna pole mounting clamp
GSM/EDGE 900, 1800 and 1900 combiners
Table 16.
Combiners for the Nokia MetroSite EDGE Base Station
Item
Product code
GSM/EDGE 900 BTS 2-to-1 combiner
CS72216.01
GSM/EDGE 1800 BTS 2-to-1 combiner
CS72216.02
GSM/EDGE 1900 BTS 2-to-1 combiner
CS72216.03
Product code: CS72216.01; CS72216.02; CS72216.03
The GSM/EDGE combiner is a cost-effective solution for combining two
MetroSite TRXs into a single antenna and feeder system.
38 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
The GSM/EDGE combiner allows you to combine the transmit signals from the
transceivers and also divide receive signals from the antenna to those
transceivers.
The GSM/EDGE 900, 1800 and 1900 combiners function in an identical manner
and are designed for mounting outdoors. The combiners are compact,
lightweight, easy to install, and require no maintenance.
Figure 13.
DN99252966
Issue 3-0 en
GSM/EDGE combiner
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
39 (66)
Solution Accessories
Figure 14.
Dimensions of the GSM/EDGE combiner
Table 17.
Specifications for the GSM/EDGE combiners
GSM 900
Combiner
GSM 1800
Combiner
GSM 1900
Combiner
Frequency range
925-960 MHz
1805-1880 MHz
1930-1990 MHz
Impedance
50 Ω
50 Ω
50 Ω
Insertion loss
3.5 dB maximum
3.5 dB maximum
3.5 dB maximum
Antenna port
return loss
18 dB minimum
18 dB minimum
18 dB minimum
BTS port return
loss
18 dB minimum
18 dB minimum
18 dB minimum
Isolation BTS
port to BTS port
(antenna port
loaded to 50 Ω
25 dB minimum
25 dB minimum
25 dB minimum
Power handling
2 x 10 W
2 x 10 W
2 x 10 W
Transmit Path:
Receive Path:
40 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Table 17.
Specifications for the GSM/EDGE combiners (Continued)
GSM 900
Combiner
GSM 1800
Combiner
GSM 1900
Combiner
Frequency range
880-915 MHz
1710-1785
1850-1910
Impedance
50 Ω
50 Ω
50 Ω
Insertion loss
3.5 dB maximum
3.5 dB maximum
3.5 dB maximum
Antenna port
return loss
18 dB minimum
18 dB minimum
18 dB minimum
BTS port return
loss
18 dB maximum
18 dB maximum
18 dB maximum
Power division
imbalance
0.5 dB maximum
0.5 dB maximum
0.5 dB maximum
Intermodulation: 2 x 10 W unmodulated carriers:
Antenna port
880-915 MHz: 100 dBm
maximum
1710-1785 MHz: 100 dBm maximum
1850-1910 MHz: 100 dBm maximum
BTS port
880-915 MHz: 116 dBm
maximum
1710-1785 MHz: 116 dBm maximum
1850-1910 MHz: 116 dBm maximum
Outside the
bands indicated
-38 dBm maximum
-38 dBm maximum
-38 dBm maximum
W x H x D mm
139 x 117
(including
connectors) x 27
mm
139 x 117
(including
connectors) x 27
mm
139 x 117
(including
connectors) x 27
mm
Weight
680 g
680 g
680 g
Connectors
N type female
(silver plated)
N type female
(silver plated)
N type female
(silver plated)
Enclosure
Aluminium; RAL
7047
Aluminium; RAL
7047
Aluminium; RAL
7047
Protection
IP65
IP65
IP65
Operating
temperature
-40oC to +60oC
-40oC to +60oC
-40oC to +60oC
Lightning
specification
IEC 1312-1
IEC 1312-1
IEC 1312-1
Mechanical:
Environmental:
DN99252966
Issue 3-0 en
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
41 (66)
Solution Accessories
Table 17.
2.6
GSM 900
Combiner
GSM 1800
Combiner
GSM 1900
Combiner
Storage
Class 1.3E ETSI
300 010-1-1
Class 1.3E ETSI
300 010-1-1
Class 1.3E ETSI
300 010-1-1
Transportation
Class 2.3 ETSI
300 019-1-2
Class 2.3 ETSI 300
019-1-2
Class 2.3 ETSI 300
019-1-2
MTBF
> 500,000 hours
> 500,000 hours
> 500,000 hours
Antenna lines
Table 18.
2.6.1
Specifications for the GSM/EDGE combiners (Continued)
Antenna line accessories for the Nokia MetroSite EDGE Base
Station
Item
Product code
N-male 3/8" straight connector
CS72683.20
N-male 3/8" angle connector
CS72683.21
7-16 male, 3/8” connector for superflex
cable
CS72697
3/8" cable, RFF-50, telegrey, 250 m reel,
superflex, UV
CS72259.10
3/8" cable, RFF-50, black, 250 m reel,
superflex, UV
CS72258.10
Antenna line cables
Product code: CS72259.10 and CS72258.10
The inner conductor is copper clad aluminium wire contained in a cellular
polyethylene dielectric. The outer conductor constitutes a corrugated copper tube.
The markings on the sheath consist of the manufacturer's name, cable type, week
of manufacture, year of manufacture, and cable length in metres.
42 (66)
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Figure 15.
Antenna line cable
Table 19.
Sheath characteristics for the antenna line cable
Sheath Characteristics
Item
3/8"-50 LD GY7047
(CS72259.10)
3/8"-50 (CS72258.10)
Jacket
Telegrey, LD polyethylene
Black, LD polyethylene
IEC754-1/-2 (halogen free, noncorrosive
Yes
Yes
IEC1034 (low smoke emission)
No
No
IEC332-3C (fire retardant)
No
No
UV retardant
Yes
Yes
Minimum installation
temperature
-20o C
-20o C
Table 20.
Cable characteristics for the antenna line cable
Cable Characteristics
Item
CS72258.10 and CS72259.10
(3/8")
Mechanical:
DN99252966
Issue 3-0 en
Weight
130 kg/km
Maximum pulling force
400 N
Minimum bending radius: single bending - repeated
bending
13 mm; 25 mm
Operating temperature range
-40o C to +70o C
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
43 (66)
Solution Accessories
Table 20.
Cable characteristics for the antenna line cable (Continued)
Cable Characteristics
Item
CS72258.10 and CS72259.10
(3/8")
Electrical at +20o C
Characteristic impedance
50 + 1 Ω
Attenuation
See table
Velocity factor
0.81
Capacitance
82 pF/m
Cut-off frequency
15200 MHz
Maximum operating frequency
3000 MHz
Maximum power rating
See table
Peak RF voltage rating
1.04 kV
Peak power rating
11 kW
DC resistance: inner conductor
5.1 Ω/km
DC resistance: outer conductor
6.1 Ω/m
Table 21.
Attenuation and power characteristics for the antenna line cable
Attenuation (maximum) and power rating
CS72258.10 and CS72259.10 (3/8”)
Frequency
(MHz)
44 (66)
Attenuatio
n at
ambient
Power
rating at
ambient
Power
rating at
ambient
temp. 20o
C dB/100
temp.40o C
inner
conductor
temp.40o
C inner
conducto
+70o C
(kW)
r +100o C
(kW)
700
12.1
0.32
0.69
800
13.0
0.30
0.64
850
13.4
0.29
0.62
900
13.9
0.29
0.60
950
14.3
0.28
0.58
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
DN99252966
Issue 3-0 en
Accessories and specifications
Table 21.
Attenuation and power characteristics for the antenna line cable
Attenuation (maximum) and power rating
CS72258.10 and CS72259.10 (3/8”)
Frequency
(MHz)
2.6.2
Attenuatio
n at
ambient
Power
rating at
ambient
Power
rating at
ambient
temp. 20o
C dB/100
temp.40o C
inner
conductor
temp.40o
C inner
conducto
+70o C
(kW)
r +100o C
(kW)
1000
14.7
0.26
0.57
1200
16.3
0.24
0.51
1400
17.8
0.22
0.47
1600
19.1
0.20
0.44
1800
20.5
0.19
0.41
1900
21.1
0.18
0.40
2000
21.8
0.18
0.39
2200
23.0
0.17
0.37
N male connector: straight
Product code: CS72683.20 (3/8")
This connector type is suitable for 3/8 inch helical cable and facilitates solderless
attachment of the inner wire of the connected cable.
Figure 16.
DN99252966
Issue 3-0 en
N male connector
© Nokia Corporation
Nokia Proprietary and Confidential
Draft
45 (66)
Solution Accessories
Table 22.
Specifications for the N male connector
Item
CS72683.20 (3/8")
Frequency f/GHz
0
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Producer                        : Acrobat Distiller 4.0 for Windows
Creator                         : FrameMaker 5.5.6.
Modify Date                     : 2002:10:10 17:09:30+03:00
Create Date                     : 2002:10:10 17:14:02
Title                           : dn99252966x3x0xen
Page Count                      : 66
Page Mode                       : UseOutlines


EXIF Metadata provided by EXIF.tools
FCC ID Filing: L7KWTFA-01

Navigation menu