Nokia Solutions and Networks WTPA-01 GSM 1900 Transceiver User Manual dn99252966x3x0xen

Nokia Solutions and Networks GSM 1900 Transceiver dn99252966x3x0xen

Solution Accessories

Nokia MetroSite EDGE Base StationDN99252966 © Nokia Corporation Draft 1 (66)Issue 3-0 en Nokia Proprietary and ConfidentialSolution Accessories
Solution Accessories2 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enThe information in this documentation is subject to change without notice and describes onlythe product defined in the introduction of this documentation. This documentation is intendedfor the use of Nokia's customers only for the purposes of the agreement under which thedocumentation is submitted, and no part of it may be reproduced or transmitted in any form ormeans without the prior written permission of Nokia. The documentation has been prepared tobe used by professional and properly trained personnel, and the customer assumes fullresponsibility when using it. Nokia welcomes customer comments as part of the process ofcontinuous development and improvement of the documentation.The information or statements given in this documentation concerning the suitability, capacity,or performance of the mentioned hardware or software products cannot be considered bindingbut shall be defined in the agreement made between Nokia and the customer. However, Nokiahas made all reasonable efforts to ensure that the instructions contained in the documentationare adequate and free of material errors and omissions. Nokia will, if necessary, explain issueswhich may not be covered by the documentation.Nokia's liability for any errors in the documentation is limited to the documentary correction oferrors. NOKIA WILL NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCIDENTAL OR CONSEQUENTIAL(INCLUDING MONETARY LOSSES), that might arise from the use of this documentation orthe information in it.This documentation and the product it describes are considered protected by copyrightaccording to the applicable laws.NOKIA logo is a registered trademark of Nokia Corporation.Other product names mentioned in this documentation may be trademarks of their respectivecompanies, and they are mentioned for identification purposes only.Copyright © Nokia Corporation 2002. All rights reserved.
DN99252966 © Nokia Corporation Draft 3 (66)Issue 3-0 en Nokia Proprietary and ConfidentialHereby, Nokia Corporation, declares that this product is in compliance with theessential requirements and other relevant provisions of Directive: 1999/5/EC.The product is marked with the CE marking and Notified Body number according to theDirective 1999/5/EC.FCC FCC §15.21 - Information to user - This product is used as an intentional radiatedequipment and any changes or modifications on the equipment without any approvalby Nokia could void the user's authority to operate the equipment.FCC §15.105 - Information to user - This equipment has been tested and found tocomply with the limits for a Class B digital device, pursuant to part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, thereis no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which canbe determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced radio/TV technician for help.0523
Solution Accessories4 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en
DN99252966 © Nokia Corporation Draft 5 (66)Issue 3-0 en Nokia Proprietary and ConfidentialContentsContents 5List of tables 7List of figures 9Summary of changes 111 About this document 132 Accessories and specifications 152.1 Flexbus accessories 152.1.1 Flexbus cable specifications 152.1.2 TNC male connector specifications (straight and right-angled) 172.2 Local Management Port accessories 202.2.1 Q1 LMP cable specifications 202.3 Abis PCM cable 212.3.1 PCM cable 75 ohm 222.3.2 PCM cable 120 ohm 222.3.3 BT43 plug 232.3.4 TQ plug 232.4 MetroSite antennas 232.4.1 MetroSite 130o panel antenna 242.4.2 MetroSite XX-pol panel antenna 262.4.3 Omni dual band antenna 312.4.4 Indoor omni multi-band antenna 342.4.5 Indoor multi-band panel antenna 352.4.6 Pole mounting clamps (50-115 mm pole diameter) 372.5 GSM/EDGE 900, 1800 and 1900 combiners 382.6 Antenna lines 422.6.1 Antenna line cables 422.6.2 N male connector: straight 452.6.3 N male connector: right angled 462.6.4 7-16 Straight Male connector 482.7 MetroSite Battery Backup Unit 492.7.1 Battery Backup Unit 492.7.2 Mains power cable (230 VAC) 492.7.3 230/110 VAC output cable 502.7.4 Alarm cable 512.7.5 Battery connection kit 522.8 Miscellaneous 532.8.1 Jumper cables 542.8.2 Grounding cable 542.8.3 AC power cables for MetroSite BTS or MetroHub 552.8.4 DC power cable for MetroSite BTS or MetroHub 562.8.5 Optical Alignment Tool 573 Attachments 59
Solution Accessories6 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en
DN99252966 © Nokia Corporation Draft 7 (66)Issue 3-0 en Nokia Proprietary and ConfidentialList of tablesTable 1. Flexbus accessories for the MetroSite EDGE Base Station 15Table 2. Flexbus cable specifications 17Table 3. LMP accessories for the MetroSite EDGE Base Station 20Table 4. LMP cable connector specifications 20Table 5. Abis PCM cable and accessories 21Table 6. PCM cable 75 Ω specifications 22Table 7. PCM cable 120 Ω specifications 22Table 8. Antennas for the Nokia MetroSite EDGE Base Station 23Table 9. Specifications for the 130o antenna 25Table 10. Specifications for the MetroSite XX-pol 900/1800 MHz panel antenna 27Table 11. Specifications for the MetroSite XX-pol 850/1900 MHz panel antenna 30Table 12. Specifications for the omni-directional 900/1800 MHz dual bandantenna 31Table 13. Specifications for the omni-directional 850/1900 MHz dual bandantenna 33Table 14. Specifications for the indoor omni multi-band antenna 35Table 15. Specifications for the indoor multi-band panel antenna 36Table 16. Combiners for the Nokia MetroSite EDGE Base Station 38Table 17. Specifications for the GSM/EDGE combiners 40Table 18. Antenna line accessories for the Nokia MetroSite EDGE BaseStation 42Table 19. Sheath characteristics for the antenna line cable 43Table 20. Cable characteristics for the antenna line cable 43Table 21. Attenuation and power characteristics for the antenna line cable 44Table 22. Specifications for the N male connector 46Table 23. Specifications for the N male connector, right angled 47Table 24. Specifications for the N male connector, right angled 48Table 25. Specifications for the 230 VAC mains power cable 50Table 26. Specifications for the 230/110 VAC mains power cable 51Table 27. Specifications for the alarm cable 52
Solution Accessories8 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enTable 28. Contents of the battery connection kit 52Table 29. Miscellaneous accessories for the Nokia MetroSite EDGE BaseStation 53Table 30. Jumper cable accessories 54Table 31. Grounding cable specifications 54Table 32. Specifications for the 230 VAC power cable 55Table 33. Specifications for the 110 VAC power cable 56Table 34. Specifications for the DC power cable 56Table 35. Specifications for the optical alignment tool 58
DN99252966 © Nokia Corporation Draft 9 (66)Issue 3-0 en Nokia Proprietary and ConfidentialList of figuresFigure 1. Flexbus cable 16Figure 2. TNC connectors 19Figure 3. LMP cable and connectors 21Figure 4. MetroSite 130o panel antenna 25Figure 5. MetroSite XX-pol 900/1800 MHz panel antenna 27Figure 6. MetroSite XX-pol 850/1900 MHz panel antenna 29Figure 7. Omni-directional dual band 900/1800 MHz antenna 31Figure 8. Omni-directional dual band 850/1900 MHz antenna 33Figure 9. Indoor omni multi-band antenna 34Figure 10. Indoor multi-band panel antenna 36Figure 11. Installing the indoor multi-band panel antenna 37Figure 12. Antenna pole mounting clamp 38Figure 13. GSM/EDGE combiner 39Figure 14. Dimensions of the GSM/EDGE combiner 40Figure 15. Antenna line cable 43Figure 16. N male connector 45Figure 17. N male connector, right angled 47Figure 18. 7-16 Straight male connector 48Figure 19. Battery connection kit 53Figure 20. Optical alignment tool 57
Solution Accessories10 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en
DN99252966 © Nokia Corporation Draft 11 (66)Issue 3-0 en Nokia Proprietary and ConfidentialSummary of changesVersion 1-0, 5th March, 1999. Norman M. Thomas.Version 2-0, 30th August 2001. Tyrone Williams.Version 3-0, August 2002. Kudos (Celia Pires, Mark Seymour). Added chainingextension cables into “Miscellaneous”, made corrections to specificationsfollowing comments from Jan Ekman, Tomi Karvonen and Peter Berghall.Version 3-0, October 2002. Kudos (Mark Seymour). Product codes updated.800/1900 MHz antennas added.
Solution Accessories12 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en
About this documentDN99252966 © Nokia Corporation Draft 13 (66)Issue 3-0 en Nokia Proprietary and Confidential1About this documentThis document lists the Nokia accessories which are available to support theNokia MetroSiteTM Base Station. Descriptions and specifications of theaccessories are also included.For more information and ordering of the accessories, contact your local Nokiacustomer services representative.
Solution Accessories14 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en
Accessories and specificationsDN99252966 © Nokia Corporation Draft 15 (66)Issue 3-0 en Nokia Proprietary and Confidential2Accessories and specifications2.1 Flexbus accessories2.1.1 Flexbus cable specificationsProduct codes: T36626.01 (RG223); T36629.01 (RG214)This coaxial cable is suitable for both straight and right-angled BNC/TNC plugconnector types. Flexbus uses 50 Ω cable with TNC male connectors of bothtypes, as applicable.Table 1. Flexbus accessories for the MetroSite EDGE Base StationItem Product codeJumper cable, 2.5 m, TNC (m) - TNC (f) CS72450.10RG223, 4 m, TNC-TNC straight T36625.02RG223, 8 m, TNC-TNC straight T36625.03RG223, 15 m, TNC-TNC straight T36625.04TNC male for flexbus cable straight(RG214)T36630.01TNC male for flexbus cable 90 degree(RG214)T36631.01TNC male for flexbus cable straight(RG223)T36627.01TNC male for flexbus cable 90 degree(RG223)T36627.02Flexbus cable, RG223, 500 m reel T36626.01Flexbus cable, RG214, 500 m reel T36629.01
Solution Accessories16 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enThe cable is capable of handling frequencies up to 2.8 GHz and is, for example,used to connect the radio outdoor unit to the transmission unit.Table 2 and Figure 1 identify the diameter of the cable attributes. The 'D' and 'E'min-max ranges allow for the different connectors used.Cables, type RG223, of 4 m, 8 m and 15 m lengths terminated with TNC malestraight connectors are available. The product code for each of these is identifiedin Table 1.Figure 1. Flexbus cable
Accessories and specificationsDN99252966 © Nokia Corporation Draft 17 (66)Issue 3-0 en Nokia Proprietary and Confidential2.1.2 TNC male connector specifications (straight and right-angled)Product code: T36630.01 and T36631.01 (RG214); T36627.01 and T36627.02(RG223)RF one step TNC connectors are single piece assemblies for the centre conductorand the braid of a broad range of coaxial cables. The connectors are fullycompliant with MIL-C-39012 connectors. In this case, 50 Ω versions are used.The features of these connectors include:Table 2. Flexbus cable specificationsParameter RG214 cable G223 cableDetailInner Conductor 2.28 mm diameterSilver plated copper wires (7)5.6 Ω/km at 20oC50+/- 2 Ω impedance101 nf/km capacitance at 800 Hz201 g/m weightAttenuation: 23 dB/100 m at 800 MHz.Specification: DIN 40500/T40.9 mm diameterSilver plated copper wire (single)29.4 Ω/km at 20oC50+/- 2 Ω impedance106 nf/km capacitance at 800 Hz59 g/m weightAttenuation: 69 dB/100 m at 1000 MHzSpecification: DIN 40500/T4Dielectric Core 7.4 mm diameterPEColour: neutral3.05 mm diameterPEColour: neutralOuter conductor(layer 1)Braided shield, silver plated copperwiresSpecification: DIN 40500/T4Braided shield, silver plated copper wiresSpecification: DIN 40500/T4Outer conductor(layer 2)9.1 mm diameter maximumBraided shield, silver plated copperwiresSpecification: DIN 40500/T44.39 mm diameter maximumBraided shield, copper plated wiresSpecification: DIN 40500/T4Sheath 10.9 mm diameterPVCBlackSpecification: DIN 535055.55 -0.2 mm diameterPVCBlackSpecification: DIN 53505
Solution Accessories18 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en• exceptional cable retention force to withstand vibration and frequentconnections and disconnections• long term reliability• usable with RG/U and Raychem Cheminax cables• meets performance requirements of MIL-C-39012 up to 2.8 GHzOnly the right-angled connectors are used with type RG214 cable because of thecable's rigidity.
Accessories and specificationsDN99252966 © Nokia Corporation Draft 19 (66)Issue 3-0 en Nokia Proprietary and ConfidentialFigure 2. TNC connectors
Solution Accessories20 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enNote2.2 Local Management Port accessories2.2.1 Q1 LMP cable specificationsProduct code: T55270.01This is an RS232 cable terminated with a BQ bayonet type connector at one endand a 9-pin `D' type (D9F) connector at the other end. The length of the cable is2,5 m and is provided already assembled.RD = Received DataTD = Transmitted DataGND = Groundn/c = not connectedThe pins of each connector correlate as shown in Table 4. For example, pin 1 ofconnector BQ connects to pin 3 of the ‘D’ type connector.Table 3. LMP accessories for the MetroSite EDGE Base StationItem Product codeNokia Q1 LMP cable T55270.01Table 4. LMP cable connector specificationsBQ Connector ‘D’ type ConnectorPin No. Function Pin No. Function1 LMP in 3 TD2 n/c 1, 4, 6-9 n/c3 LMP out 2 RD4 GND 5 GND
Accessories and specificationsDN99252966 © Nokia Corporation Draft 21 (66)Issue 3-0 en Nokia Proprietary and ConfidentialFigure 3. LMP cable and connectors2.3 Abis PCM cable4321432159876= Hole= Pin1 nc2 RD3 TD4 nc5 GND6 nc7 nc8 nc9 nc3 LMP out2 LMP in4 GND2 nc GND = GroundRD = Received dataTD = Transmitted datanc = not connectedBQ on the BTS endof cable D9P (female) on the PC end of cableTable 5. Abis PCM cable and accessoriesItem Product codeAbis PCM cable for MetroSite, 3 m, 120 ΩT36612.01Abis PCM cable for MetroSite, 15 m, 120ΩT36612.05Abis PCM cable for MetroSite, 50 m, 120ΩT36612.04Abis PCM cable, 75 Ω/m T36602.01Abis PCM cable, 120 Ω/m T36614.01BT43 plug, 75 Ω, 6 pieces for ABC cable T36601.01TQ plug, 120 Ω, 1 piece CS73214.02
Solution Accessories22 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en2.3.1 PCM cable 75 ohmProduct Code: T36602.01The 75 Ω PCM cable is used for 2 Mbit transmission between the NokiaMetroSite EDGE Base Station and a BSC. This high quality coaxial cableconsists of a plain copper inner conductor, polyethylene dielectric material, twocopper braids, and a PVC outer jacket.2.3.2 PCM cable 120 ohmProduct Code: T36614.01The 120 Ω PCM cable is used for 2 Mbit transmission between the NokiaMetroSite EDGE Base Station and a BSC. This high quality cable consists of fourbare copper wires, polyethylene wire insulation, intermediate plastic tapeinsulation, tinned copper wire gauze, and a halogen-free outer sheath.The cables available are 3 m, 15 m, and 50 m, terminated with a TQ plug at eachend.Table 6. PCM cable 75 Ω specificationsCharacteristic impedance 75+ / - 4 ΩMutual capacitance 67 pF/mWave attenuation 1 MHz 2.3 dB/100 mWave attenuation 4 MHz 4.5 dB/100 mWave attenuation 20 MHz 9.2 dB/100 mOperating voltage 300 V rmsMinimum bending radius 18 mmDiameter 3.55 mmColour BlackTable 7. PCM cable 120 Ω specificationsCharacteristic impedance 120+ / - 10 ΩMutual capacitance 40 nF/kmWave attenuation 1 MHz 1.7 dB/100 mWave attenuation 4 MHz 3.5 dB/100 m
Accessories and specificationsDN99252966 © Nokia Corporation Draft 23 (66)Issue 3-0 en Nokia Proprietary and Confidential2.3.3 BT43 plugProduct code: T36601.01This connector is used with the TZC5024 cable. For connection of this plug to theAbis 75 Ω coaxial cable, refer to Attachment 1.2.3.4 TQ plugProduct code: CS73214.02This Abis 120 Ω interface connector supports the use of cables with outerdiameter of 4-13 mm and wires of dimension AWG 26-30.For connection of this plug to the Abis 120 Ω cable refer to Attachment 2. Thecable is provided already assembled and is 2 m in length.2.4 MetroSite antennasWave attenuation 20 MHz 7.8 dB/100 mOperating voltage 300 V rmsMinimum bending radius 30 mmDiameter 4.1 mmColour GreyTable 7. PCM cable 120 Ω specifications (Continued)Table 8. Antennas for the Nokia MetroSite EDGE Base StationItem Product codeMetroSite 130o panel antenna, dual band870-960 / 1710-1880 MHz, 5 dBi, 2 x Nfemale connectorsCS72454.01MetroSite XX-pol panel antenna, dualband 870-960 / 1710-1880 MHz, 65o,12.5/13.5 dBi, 4 portCS72180MetroSite XX-pol panel antenna, dualband 824-960 / 1710-2170 MHz, 65o,14.5/17.5 dBiCS72763.01
Solution Accessories24 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en2.4.1 MetroSite 130o panel antennaProduct code: CS72454.01This antenna is a vertically polarised, dual band, two-port antenna providing 130ocoverage with a gain of 6 dBi.MetroSite omni antenna, dual band 870-960 / 1710-1880 MHz, 2 dBi, 2 x N femaleconnectorsCS72187MetroSite omni antenna, dual band 824-960 / 1805-2170 MHz, 2 dBi, N femaleCS72187.02Indoor omni antenna, multi-band 824-960/ 1425-2170 MHz, 2 dBi, 360o, N femaleCS72166Indoor panel antenna, multi-band 824-960/ 1425-2170 MHz, 7 dBi, 90o, N femaleCS72168Single pole mounting clamp for 50-115mm polesCS72196Table 8. Antennas for the Nokia MetroSite EDGE Base Station (Continued)Item Product code
Accessories and specificationsDN99252966 © Nokia Corporation Draft 25 (66)Issue 3-0 en Nokia Proprietary and ConfidentialFigure 4. MetroSite 130o panel antennaTable 9. Specifications for the 130o antennaItem GSM 900 GSM 1800Frequency range 870-960 MHz 1710-1880 MHzVSWR < 1:1.7 < 1:1.7Gain 6 dBi 6 dBiImpedance 50 Ω50 ΩPolarization Vertical VerticalFront-to-back ratio (co-polar)> 10 dB > 10 dBHalf power beam width Horizontal: 130oVertical: 55oHorizontal: 130oVertical: 55oMaximum power/input (at25o C)50 W 50 W
Solution Accessories26 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enNote2.4.2 MetroSite XX-pol panel antennaProduct codes: CS72180, CS72763.01This is a four port, dual band antenna. Its output is cross polarised + / - 45 o andprovides 65 o coverage with a gain of 12.5 to 13.5 dBi for the 900/1800 MHzantenna and 14.5 to 17.5 dBi for the 850/1900 MHz antenna (see also the notebelow).Further variations of the Nokia MetroSite XX-pol panel 850/1900 MHz antennasare available. Please contact your Nokia representative.Isolation > 25 dB (GSM 900 - GSM 900) on Tx band > 30 dB(GSM 1800 - GSM 1800) > 30 dB (GSM 900 - GSM1800)Input 2 x N femaleConnector position BottomWeight 2.0 kg (without packaging)Wind load Frontal: 27 N (at 150 km/h) Lateral: 16 N (at 150 km/h)Rear side: 63 N (at 150 km/h)Maximum wind velocity 150 km/hPacking size 480 x 125 x 110 mmHeight x width x depth 452 x 95 x 100 mmMaterial Reflector screen: painted aluminium Radome: ABS;grey NCS S 2500-N screws and nuts: stainless steelMounting TBAIce protection The antenna remains operational during icy conditionsGrounding The metal parts of the antenna, including the mountingkit are DC grounded.Table 9. Specifications for the 130o antenna (Continued)Item GSM 900 GSM 1800
Accessories and specificationsDN99252966 © Nokia Corporation Draft 27 (66)Issue 3-0 en Nokia Proprietary and Confidential900/1800 MHz XX-pol panel antenna (CS72180)Figure 5. MetroSite XX-pol 900/1800 MHz panel antennaTable 10. Specifications for the MetroSite XX-pol 900/1800 MHz panelantennaItem GSM 900 GSM 1800Frequency range 870-960 MHz 1710-1880 MHzVSWR < 1.5 < 1.5Impedance 50 Ω50 Ω
Solution Accessories28 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enPolarization +45o ; -45o+45o ; -45oFront-to-back ratio (co-polar)> 30 dB > 30 dBHalf power beam width +45o / -45oHorizontal: 65oVertical: 28o+45o / -45oHorizontal: 65oVertical: 28oMaximum power/input (at50o C)250 W 150 WIsolation > 30 dB (GSM 900 - GSM 900) > 30 dB (GSM 1800 -GSM 1800) > 30 dB (GSM 900 - GSM 1800)Input 4 x 7-16 femaleConnector position Top or bottomWeight 7 kgWind load (at 150 km/h) Frontal: 110 N. Lateral: 60 N. Rearside: 240 N.Maximum wind velocity 200 km/hPacking size 782 x 287 x 165 mmHeight / width / depth 656 mm / 262 mm / 116 mmMaterial Reflector screen: weather proof aluminium Radome:fibreglass (white)Screws and nuts: stainless steelMounting Walls: using two mounting plates already attached tothe antennaMasts: using two clamps suitable for the mast diameterIce protection The antenna remains operational under icy conditionsGrounding The metal parts of the antenna, including the mountingkit and the inner conductors are DC grounded.Table 10. Specifications for the MetroSite XX-pol 900/1800 MHz panelantenna (Continued)Item GSM 900 GSM 1800
Accessories and specificationsDN99252966 © Nokia Corporation Draft 29 (66)Issue 3-0 en Nokia Proprietary and Confidential850/1900 MHz XX-pol panel antenna (CS72763.01)Figure 6. MetroSite XX-pol 850/1900 MHz panel antenna
Solution Accessories30 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enTable 11. Specifications for the MetroSite XX-pol 850/1900 MHz panelantennaItem GSM 850 GSM 1900Frequency range 824-960 MHz 1710-2170 MHzVSWR < 1.5 < 1.5Impedance 50 Ω50 ΩPolarization +45o ; -45o+45o ; -45oFront-to-back ratio (co-polar)> 28 dB > 25 dBHalf power beam width +45o / -45oHorizontal: 68 - 65oVertical: 16 - 14.5o+45o / -45oHorizontal: 65 - 63oVertical: 7.5 - 6.5oMaximum power/input (at50o C)250 W 200 WIsolation: intrasystem > 30 dBIsolation: intersystem > 45 dBInput 4 x 7-16 femaleConnector position Top or bottomWeight 16.5 kgWind load (at 150 km/h) Frontal: 230 N. Lateral: 180 N. Rearside: 430 N.Maximum wind velocity 200 km/hPacking size 1590 x 287 x 177 mmHeight / width / depth 1296 mm / 262 mm / 139 mmMaterial Reflector screen: weather proof aluminium Radome:fibreglass (white)Screws and nuts: stainless steelMounting Walls: using two mounting plates already attached tothe antennaMasts: using two clamps suitable for the mast diameterIce protection The antenna remains operational under icy conditionsGrounding The metal parts of the antenna, including the mountingkit and the inner conductors are DC grounded. Theinputs 824-960 MHz are also DC grounded. The inputs1710-2170 MHz are coupled capacitively.
Accessories and specificationsDN99252966 © Nokia Corporation Draft 31 (66)Issue 3-0 en Nokia Proprietary and Confidential2.4.3 Omni dual band antennaProduct codes: CS72187, CS72187.02This is a dual port, dual band 900/1800 or 850/1900 MHz antenna. The output isomni-directional (360o) with a gain of 2 dBi and has two units (upper and lower).900/1800 MHz omni-directional, dual band antenna (CS72187)Figure 7. Omni-directional dual band 900/1800 MHz antennaTable 12. Specifications for the omni-directional 900/1800 MHz dual bandantennaInput 2 x N femaleFrequency range 870-960 MHz and 1710-1880 MHz for the upperand lower unitsVSWR < 1.8Gain 2 dBiImpedance 50 Ω
Solution Accessories32 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enPolarization VerticalIsolation > 25 dBMaximum power/input 50 W at 50oC ambient temperatureWeight 1.2 kgRadome diameter 30 mmWind load 30 N at 150 km/hMaximum wind load 200 km/hPacking size 700 x 80 x 80 mm (approximately)Height 500 mmMaterial Radiator: copper, brassRadome: fibreglass (grey)Base: weatherproof aluminiumMounting clamp and screws: stainless steelMounting Attached laterally at the tip of a tubular mast of40-70 mm diameter. The connecting cable (notsupplied) runs outside the mast.Range of application Urban areas, preferably in places aroundbuildings at low or medium heights above groundlevel or light poles or short masts on rooftops.The antenna shape reduces the optical impact.Grounding All metal parts of the antenna and the mountingkit (excluding the inner conductor of the upperunit) are DC grounded.Table 12. Specifications for the omni-directional 900/1800 MHz dual bandantenna (Continued)
Accessories and specificationsDN99252966 © Nokia Corporation Draft 33 (66)Issue 3-0 en Nokia Proprietary and Confidential850/1900 MHz omni-directional, dual band antenna (CS72187.02)Figure 8. Omni-directional dual band 850/1900 MHz antennaTable 13. Specifications for the omni-directional 850/1900 MHz dual bandantennaInput 2 x N femaleFrequency range 824-960 MHz and 1805-2170 MHz for the upperand lower unitsVSWR < 2.0Gain 2 dBiImpedance 50 ΩPolarization VerticalMaximum power/input 50 W at 50oC ambient temperatureWeight 250 gRadome diameter 20 mm
Solution Accessories34 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en2.4.4 Indoor omni multi-band antennaProduct code: CS72166This is a single port, multi-band 850/900/1800/1900 MHz antenna. This antennais vertically polarised and the horizontal radiation pattern is omni-directional(360o) with a gain of 2 dBi. The antenna can be operated in all frequency rangessimultaneously, and needs no additional groundplane.Figure 9. Indoor omni multi-band antennaHeight 216 mmMaterial Radiator: brassRadome: fibreglass (white)Base: weatherproof aluminiumMounting clamp and screws: stainless steelMounting One hole mounting (16 mm) to surfaces ofmaximum 10 mm thickness or attached laterallyat the tip of a tubular mast of 40-70 mm diameter.Range of application Urban areas, preferably in places aroundbuildings at low or medium heights above groundlevel or light poles or short masts on rooftops.The antenna shape reduces the optical impact.Grounding All metal parts of the antenna and the mountingkit (excluding the inner conductor of the upperunit) are DC grounded.Table 13. Specifications for the omni-directional 850/1900 MHz dual bandantenna (Continued)
Accessories and specificationsDN99252966 © Nokia Corporation Draft 35 (66)Issue 3-0 en Nokia Proprietary and Confidential2.4.5 Indoor multi-band panel antennaProduct code: CS72168This is a single port, multi-band indoor panel antenna. The antenna has a halfpower beam width of 90 o with a gain of 7 dBi.Table 14. Specifications for the indoor omni multi-band antennaInput N femaleFrequency range 824-960 MHz and 1425-2170 MHzVSWR < 2.0: 824-960MHz< 2.0: 1425-1710MHz< 1.6: 1710-1990MHz< 2.0: 1990-2170MHzGain 2 dBiInput 1 x N femaleImpedance 50 ΩPolarization VerticalMaximum power (at 50o C) 50 W /bandWeight 400 gDiameter 260 mmHeight 78 mm (without connector)Material Base: aluminiumProtective housing: high impactpolystyrolColour: whiteAdditional painting is possibleMounting Three holes in the base to enablemounting on a ceiling. Two types ofscrews are supplied. N connector: a holeof 35 mm diameter needed in the ceiling.Grounding All metal parts including the innerconductor are DC grounded.
Solution Accessories36 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enFigure 10. Indoor multi-band panel antennaTable 15. Specifications for the indoor multi-band panel antennaInput Cable RG 223/CU of 1 m length; white; Nfemale connector.Frequency range 824-960 MHz and 1710-2170 MHzVSWR 870-960 MHz and 1710-1900 MHz: < 1.6824-960 MHz and 1710-2170 MHz: < 2.0Gain 7 dBi approximatelyImpedance 50 ΩPolarization VerticalHalf power beam width Horizontal; 90oMaximum power (at 50o C) 25 WWeight 500 gPacking size 321 x 165 x 50 mmHeight x width x depth 205 x 155 x 42 mmMaterial Radiator: brassReflector: AluminiumRadome: ABS (white)Mounting plates: stainless steelMounting Two holes of 6 mm diameter in themounting plate.Grounding All metal parts and inner conductor DCgrounded.
Accessories and specificationsDN99252966 © Nokia Corporation Draft 37 (66)Issue 3-0 en Nokia Proprietary and ConfidentialInstalling the multi-band indoor panel antenna1. Fix the attachment plate to the wall using two 4 mm diameter screws. See[1] in Figure 11.2. Align the antenna over the attachment plate, keeping the cable in themiddle of the plate. See [2] in Figure 11.3. Pull the antenna downwards until it clicks into place. See [3] in Figure 11.Do not pull the antenna downwards with the antenna cable.Figure 11. Installing the indoor multi-band panel antenna2.4.6 Pole mounting clamps (50-115 mm pole diameter)Product code: CS72196This standard single unit clamp is suitable for standard Nokia antennas.The number of clamps required depends upon the antenna.
Solution Accessories38 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enFigure 12. Antenna pole mounting clamp2.5 GSM/EDGE 900, 1800 and 1900 combinersProduct code: CS72216.01; CS72216.02; CS72216.03The GSM/EDGE combiner is a cost-effective solution for combining twoMetroSite TRXs into a single antenna and feeder system.Table 16. Combiners for the Nokia MetroSite EDGE Base StationItem Product codeGSM/EDGE 900 BTS 2-to-1 combiner CS72216.01GSM/EDGE 1800 BTS 2-to-1 combiner CS72216.02GSM/EDGE 1900 BTS 2-to-1 combiner CS72216.03
Accessories and specificationsDN99252966 © Nokia Corporation Draft 39 (66)Issue 3-0 en Nokia Proprietary and ConfidentialThe GSM/EDGE combiner allows you to combine the transmit signals from thetransceivers and also divide receive signals from the antenna to thosetransceivers.The GSM/EDGE 900, 1800 and 1900 combiners function in an identical mannerand are designed for mounting outdoors. The combiners are compact,lightweight, easy to install, and require no maintenance.Figure 13. GSM/EDGE combiner
Solution Accessories40 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enFigure 14. Dimensions of the GSM/EDGE combinerTable 17. Specifications for the GSM/EDGE combinersGSM 900CombinerGSM 1800CombinerGSM 1900CombinerTransmit Path:Frequency range 925-960 MHz 1805-1880 MHz 1930-1990 MHzImpedance 50 Ω50 Ω50 ΩInsertion loss 3.5 dB maximum 3.5 dB maximum 3.5 dB maximumAntenna portreturn loss18 dB minimum 18 dB minimum 18 dB minimumBTS port returnloss18 dB minimum 18 dB minimum 18 dB minimumIsolation BTSport to BTS port(antenna portloaded to 50 Ω25 dB minimum 25 dB minimum 25 dB minimumPower handling 2 x 10 W 2 x 10 W 2 x 10 WReceive Path:
Accessories and specificationsDN99252966 © Nokia Corporation Draft 41 (66)Issue 3-0 en Nokia Proprietary and ConfidentialFrequency range 880-915 MHz 1710-1785 1850-1910Impedance 50 Ω50 Ω50 ΩInsertion loss 3.5 dB maximum 3.5 dB maximum 3.5 dB maximumAntenna portreturn loss18 dB minimum 18 dB minimum 18 dB minimumBTS port returnloss18 dB maximum 18 dB maximum 18 dB maximumPower divisionimbalance0.5 dB maximum 0.5 dB maximum 0.5 dB maximumIntermodulation: 2 x 10 W unmodulated carriers:Antenna port 880-915 MHz: -100 dBmmaximum1710-1785 MHz: -100 dBm maximum1850-1910 MHz: -100 dBm maximumBTS port 880-915 MHz: -116 dBmmaximum1710-1785 MHz: -116 dBm maximum1850-1910 MHz: -116 dBm maximumOutside thebands indicated-38 dBm maximum -38 dBm maximum -38 dBm maximumMechanical:W x H x D mm 139 x 117(includingconnectors) x 27mm139 x 117(includingconnectors) x 27mm139 x 117(includingconnectors) x 27mmWeight 680 g 680 g 680 gConnectors N type female(silver plated)N type female(silver plated)N type female(silver plated)Enclosure Aluminium; RAL7047Aluminium; RAL7047Aluminium; RAL7047Environmental:Protection IP65 IP65 IP65Operatingtemperature -40oC to +60oC -40oC to +60oC -40oC to +60oCLightningspecificationIEC 1312-1 IEC 1312-1 IEC 1312-1Table 17. Specifications for the GSM/EDGE combiners (Continued)GSM 900CombinerGSM 1800CombinerGSM 1900Combiner
Solution Accessories42 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en2.6 Antenna lines2.6.1 Antenna line cablesProduct code: CS72259.10 and CS72258.10The inner conductor is copper clad aluminium wire contained in a cellularpolyethylene dielectric. The outer conductor constitutes a corrugated copper tube.The markings on the sheath consist of the manufacturer's name, cable type, weekof manufacture, year of manufacture, and cable length in metres.Storage Class 1.3E ETSI300 010-1-1Class 1.3E ETSI300 010-1-1Class 1.3E ETSI300 010-1-1Transportation Class 2.3 ETSI300 019-1-2Class 2.3 ETSI 300019-1-2Class 2.3 ETSI 300019-1-2MTBF > 500,000 hours > 500,000 hours > 500,000 hoursTable 17. Specifications for the GSM/EDGE combiners (Continued)GSM 900CombinerGSM 1800CombinerGSM 1900CombinerTable 18. Antenna line accessories for the Nokia MetroSite EDGE BaseStationItem Product codeN-male 3/8" straight connector CS72683.20N-male 3/8" angle connector CS72683.217-16 male, 3/8” connector for superflexcableCS726973/8" cable, RFF-50, telegrey, 250 m reel,superflex, UVCS72259.103/8" cable, RFF-50, black, 250 m reel,superflex, UVCS72258.10
Accessories and specificationsDN99252966 © Nokia Corporation Draft 43 (66)Issue 3-0 en Nokia Proprietary and ConfidentialFigure 15. Antenna line cableTable 19. Sheath characteristics for the antenna line cableSheath CharacteristicsItem 3/8"-50 LD GY7047(CS72259.10)3/8"-50 (CS72258.10)Jacket Telegrey, LD polyethylene Black, LD polyethyleneIEC754-1/-2 (halogen free, non-corrosiveYes Ye sIEC1034 (low smoke emission) No NoIEC332-3C (fire retardant) No NoUV retardant Yes YesMinimum installationtemperature -20o C -20o CTable 20. Cable characteristics for the antenna line cableCable CharacteristicsItem CS72258.10 and CS72259.10(3/8")Mechanical:Weight 130 kg/kmMaximum pulling force 400 NMinimum bending radius: -single bending - repeatedbending13 mm; 25 mmOperating temperature range -40o C to +70o C
Solution Accessories44 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enElectrical at +20o CCharacteristic impedance 50 + 1 ΩAttenuation See tableVelocity factor 0.81Capacitance 82 pF/mCut-off frequency 15200 MHzMaximum operating frequency 3000 MHzMaximum power rating See tablePeak RF voltage rating 1.04 kVPeak power rating 11 kWDC resistance: inner conductor 5.1 Ω/kmDC resistance: outer conductor 6.1 Ω/mTable 21. Attenuation and power characteristics for the antenna line cableAttenuation (maximum) and power ratingCS72258.10 and CS72259.10 (3/8”)Frequency(MHz)Attenuation atambienttemp. 20oC dB/100mPowerrating atambienttemp.40oCinnerconductor+70o C(kW)Powerrating atambienttemp.40oC innerconductor +100o C(kW)700 12.1 0.32 0.69800 13.0 0.30 0.64850 13.4 0.29 0.62900 13.9 0.29 0.60950 14.3 0.28 0.58Table 20. Cable characteristics for the antenna line cable (Continued)Cable CharacteristicsItem CS72258.10 and CS72259.10(3/8")
Accessories and specificationsDN99252966 © Nokia Corporation Draft 45 (66)Issue 3-0 en Nokia Proprietary and Confidential2.6.2 N male connector: straightProduct code: CS72683.20 (3/8")This connector type is suitable for 3/8 inch helical cable and facilitates solderlessattachment of the inner wire of the connected cable.Figure 16. N male connector1000 14.7 0.26 0.571200 16.3 0.24 0.511400 17.8 0.22 0.471600 19.1 0.20 0.441800 20.5 0.19 0.411900 21.1 0.18 0.402000 21.8 0.18 0.392200 23.0 0.17 0.37Table 21. Attenuation and power characteristics for the antenna line cableAttenuation (maximum) and power ratingCS72258.10 and CS72259.10 (3/8”)Frequency(MHz)Attenuation atambienttemp. 20oC dB/100mPowerrating atambienttemp.40oCinnerconductor+70o C(kW)Powerrating atambienttemp.40oC innerconductor +100o C(kW)
Solution Accessories46 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en2.6.3 N male connector: right angledProduct code: CS72683.21 (3/8")This connector type is suitable for 3/8" helical cable and facilitates solderlessattachment of the inner wire of the connected cable.Table 22. Specifications for the N male connectorItem CS72683.20 (3/8")Frequency f/GHz 0 < f ≤ 11 < f ≤ 2.7VSWR ≤ 1.02≤ 1.03Intermodulation (2x20W;936/958MHz; 1770/1810MHz)≤ -155 dBcAssembly time < 2 minutesWeight 70 ga (mm) 47b (mm) 21
Accessories and specificationsDN99252966 © Nokia Corporation Draft 47 (66)Issue 3-0 en Nokia Proprietary and ConfidentialFigure 17. N male connector, right angledTable 23. Specifications for the N male connector, right angledItem CS72683.21 (3/8")Frequency f/GHz 0< f ≤11 < f ≤22 < f ≤ 2.72.7 < f ≤ 3.7VSWR ≤ 1.02≤ 1.04≤ 1.06≤ 1.13Intermodulation (2x20W;936/958MHz; 1770/1810MHz)≤ -155 dBcAssembly time < 2 minutesWeight 145 g
Solution Accessories48 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en2.6.4 7-16 Straight Male connectorProduct code: CS72697 (3/8")This connector type is suitable for 3/8" helical cable and facilitates solderlessattachment of the inner wire of the connected cable.Figure 18. 7-16 Straight male connectora (mm) 36b (mm) 38.3c (mm) 23Table 23. Specifications for the N male connector, right angled (Continued)Item CS72683.21 (3/8")Table 24. Specifications for the N male connector, right angledItem CS72697 (3/8")Frequency f/GHz 0 < f ≤ 11 < f ≤ 2.72.7 < f ≤ 3.7VSWR ≤ 1.02≤ 1.03≤ 1.06Intermodulation (2x20W;936/958MHz; 1770/1810MHz)≤ -155 dBc
Accessories and specificationsDN99252966 © Nokia Corporation Draft 49 (66)Issue 3-0 en Nokia Proprietary and ConfidentialNote2.7 MetroSite Battery Backup UnitProduct code: CS70401.01 for BBU (without batteries) and .02 for batteries2.7.1 Battery Backup UnitThe MetroSite BBU is designed to provide 110 VAC or 230 VAC backup supportfor connected elements.The MetroSite BBU is able to support a single MetroSite BTS or a singleMetroHub and can be pole or wall mounted in almost any location, indoors oroutdoors. Its appearance is identical to the MetroSite BTS and the MetroHub,consequently it can be readily integrated into a site location unobtrusively.2.7.2 Mains power cable (230 VAC)This item is included in CS70401.01.The 230 VAC power cables for AC connectivity are light and flexible. They canbe installed in dry, damp and wet environments, both indoor and outdoor, inaddition to fire-sensitive locations.The cable has three conductors made of high quality copper insulated withEPDM-rubber.Assembly time < 2 minutesWeight 105 ga (mm) 39b (mm) 21Table 24. Specifications for the N male connector, right angled (Continued)Item CS72697 (3/8")
Solution Accessories50 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enNoteNoteOne end of the cable is fitted with an IEC320 female connector and the other endwith an appropriate three-pin male connector for connection to the mains powersource (user defined).The MetroSite BTS or MetroHub mains power cable can be utilised forconnecting the MetroSite BBU to the mains power source.2.7.3 230/110 VAC output cableThis item is included in CS70401.01.The 230/110 VAC power cables for AC connectivity are light and flexible. Theycan be installed in dry, damp and wet environments, both indoor and outdoor, inaddition to fire-sensitive locations.The cable has three conductors made of high quality tinned copper insulated withEPDM-rubber and is 2 metres in length.Table 25. Specifications for the 230 VAC mains power cableCode DetailCross section 1.5 mm2Nominal diameter 9.0 mmNominal voltage Uo /U 300 V/500 VMaximum continuous operatingtemperature +60o CMinimum recommended handlingtemperature -50o CMinimum bending radius 54 mmLive wire colour BrownNeutral wire colour BlueEarthing cable colour Green/yellowSheath colour Black
Accessories and specificationsDN99252966 © Nokia Corporation Draft 51 (66)Issue 3-0 en Nokia Proprietary and ConfidentialNoteOne end of the cable is fitted with an IEC320 female connector and the other endwith an IEC320 male connector. The former connects to the MetroSite BBU andthe latter to a MetroSite BTS or MetroHub.2.7.4 Alarm cableThis item is included in CS70401.01.This cable facilitates the monitoring of the status of the various MetroSite BBUalarm outputs at a remote control centre via the MetroSite BTS.The cable is fitted with an X3, mini D26 (EAC) connector at each end.Table 26. Specifications for the 230/110 VAC mains power cableCode DetailCross section 1.5 mm2Nominal diameter 9.0 mmNominal voltage Uo /U 300 V/500 VMaximum continuous operatingtemperature +60o CMinimum recommended handlingtemperature -50o CMinimum bending radius 54 mmLive wire colour BrownNeutral wire colour BlueEarthing cable colour Green-yellowSheath colour Black
Solution Accessories52 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enNote2.7.5 Battery connection kitThis item is included in CS70401.01.The kit provides the connection busbars and the connector cable for the batterybackup to the MetroSite BBU. The cable which connects the batteries to theMetroSite BBU is fitted with terminals for connection to the batteries and acommon connector for connection to the MetroSite BBU -48 VDC connector.Table 27. Specifications for the alarm cablePin Signal Pin Signal1 EAC1 14 GND2 EAC2 15 GND3 EAC3 16 GND4 EAC4 17 GND5 EAC5 18 GND6 EAC6 19 GND7 EAC7 20 GND8 EAC8 21 GND9 EAC9 22 GND10 EAC10 23 GND11 CO1 24 CO312 +3 V 25 CO413 CO2 26 +5 VTable 28. Contents of the battery connection kitItem Quantity10-pin genderless connection cable 1Short battery inter-connecting busbar 2Long battery inter-connecting busbar 1
Accessories and specificationsDN99252966 © Nokia Corporation Draft 53 (66)Issue 3-0 en Nokia Proprietary and ConfidentialFigure 19. Battery connection kit2.8 MiscellaneousTable 29. Miscellaneous accessories for the Nokia MetroSite EDGE BaseStationItem Product codeEarthing cable, 16 mm2CS73174Metro Hopper optical alignment tool T55875.01Alarm cable (between BTS and Hub) CS72451.20Pole mounting kit for MetroSite cabinet CS72451.10Power cable for BTS/Hub (230 VAC) CS72452.50Power cable for BTS/Hub (110 VAC) CS72452.51Power cable for BTS (DC) CS72452.52Power cable for Hub (DC) CS72452.53Clamp for 2 x 3/8” cable CS72747.04Two-pair, 120 Ω cable, 305 m CS72452
Solution Accessories54 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en2.8.1 Jumper cables2.8.2 Grounding cableProduct Code: CS73174The grounding cable is plastic insulated copper wires with a yellow-green colourinsulation cover identification.Extension cable kit, 1 metre 469584AExtension cable kit, 3 metres 467614AExtension cable kit, 5 metres 469585AExtension adapter for PCM/clock cable CS74814Table 29. Miscellaneous accessories for the Nokia MetroSite EDGE BaseStation (Continued)Item Product codeTable 30. Jumper cable accessoriesCode DescriptionCS72672 Jumper cable 2,5 m, 3/8” N-m angle/N-m telegreyCS72680.06 Jumper cable 1,25 m, 3/8” N-m angle/N-m, telegreyCS72680.07 Jumper cable 2 m, 3/8” N-m right-angle/7-16f, telegreyTable 31. Grounding cable specificationsCode DetailsCross-section 16 mm2Nominal diameter 7.2 mmNominal voltage Uo /U 450 V/750 VMaximum continuous operatingtemperature +60o C
Accessories and specificationsDN99252966 © Nokia Corporation Draft 55 (66)Issue 3-0 en Nokia Proprietary and Confidential2.8.3 AC power cables for MetroSite BTS or MetroHubThe power cables for AC connectivity are light and flexible. They can be installedin dry, damp and wet environments, both indoor and outdoor, in addition to fire-sensitive locations.The cables have three conductors made of high quality tinned copper insulatedwith EPDM-rubber and are 10 m in length.One end of the cable is fitted with an IEC320 three-pin male connector and theother end with an appropriate three-pin male connector for connection to themains power source (user defined).230 VAC power cable: CS72452.50Minimum recommended handlingtemperature -50o CMinimum recommended bending radius(single bend)22 mmColour Yellow-greenTable 31. Grounding cable specifications (Continued)Code DetailsTable 32. Specifications for the 230 VAC power cableCode DetailCross section 1.5 mm2Nominal diameter 9.0 mmNominal voltage Uo /U 300 V/500 VMaximum continuous operating temperature +60o CMinimum recommended handling temperature -50o CMinimum bending radius 54 mmLive wire colour BrownNeutral wire colour BlueEarthing cable colour Green-yellowSheath colour Black
Solution Accessories56 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en110 VAC power cable: CS72452.512.8.4 DC power cable for MetroSite BTS or MetroHubProduct code: CS72452.52 (MetroSite); CS72452.53 (MetroHub)The -48 VDC power cables for DC connectivity are light and flexible. They canbe installed in dry, damp and wet environments, both indoor and outdoor, inaddition to fire-sensitive locations.Each cable type has three conductors made of high quality tinned copper insulatedwith EPDM-rubber and is 10 m in length.Table 33. Specifications for the 110 VAC power cableCode DetailCross section 1.5 mm2Nominal diameter 9.0 mmNominal voltage Uo /U 300 V/500 VMaximum continuous operating temperature +60o CMinimum recommended handling temperature -50o CMinimum bending radius 54 mmLive wire colour BrownNeutral wire colour BlueEarthing cable colour Green-yellowSheath colour BlackTable 34. Specifications for the DC power cableCode DetailCross section TBANominal diameter TBANominal voltage Uo /U 300 V/500 VMaximum continuous operating temperature +60o CMinimum recommended handling temperature -50o CMinimum bending radius TBA
Accessories and specificationsDN99252966 © Nokia Corporation Draft 57 (66)Issue 3-0 en Nokia Proprietary and Confidential2.8.5 Optical Alignment ToolProduct code: T55875.01The optical alignment tool is used to align the MetroHopper for optimumefficiency.The optical alignment tool is fitted on the MetroHopper mounting assemblybefore the MetroHopper is fitted. Upon switching on, a red dot is visible throughthe eyepiece and this can be adjusted for brightness. A coarse then a finealignment is carried using the red dot.The red dot is aimed towards the centre of the far-end radio and the mountingassembly is aligned accordingly. During the course of alignment, appropriatescrews are tightened to lock the mounting assembly in the aligned position.When satisfied that alignment is complete, the optical alignment tool is switchedoff and removed from the MetroHopper mounting assembly. The MetroHoppercan then be fitted to the mounting assembly.Figure 20. Optical alignment toolLive wire colour BrownNeutral wire colour BlueEarthing cable colour Green-yellowSheath colour BlackTable 34. Specifications for the DC power cable (Continued)Code Detail
Solution Accessories58 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enTable 35. Specifications for the optical alignment toolItem DetailsType Optical red dot alignment sight. ‘Aimpoint Comp’sight with a 90oviewing angle and a mounting baseperpendicular to the optical axis of sight.Manufacturer Aimpoint AB, SwedenApplication Used with MetroSite Alignment Unit, typeT55850.01Alignment ranges Alignment range with 2x magnification lens, 0.5 to 1km.4x magnification lens version: 1 kmOptical characteristics Red dot size 3 MOACalibration Factory calibrated with the optical axis setperpendicular to the base within 10 MOA. The unitcan be re-calibrated as necessary.Power source Battery operated. One lithium DL1/3N battery orsimilar.Battery life: 150-250 h (average)Mechanical characteristics Base has mechanical interface to alignment unit(T55850.01)Materials and surfacetreatmentAnodised/painted aluminium; stainless steelRequired tools One 6 mm Allen key.
AttachmentsDN99252966 © Nokia Corporation Draft 59 (66)Issue 3-0 en Nokia Proprietary and Confidential3AttachmentsAttachment 1: Installation instructions for the Abis 75-ohm interface ofNokia MetroSite with TZC75024 cableFor installation the following listed tools are needed:• CS74863 Peeling Tool• CS74862 Centre Contact Crimp Tool• CS77550.01 Crimp ToolThe connector consists of three parts: a ferrule, a jack and a body.
Solution Accessories60 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enInstructions:1. Slide the shrinking sleeve and the ferrule onto the un-peeled part of thecable.2. Peel the cable as shown in the picture. The lengths of the peeled parts are:21 mm (0.827"), 13 mm (0.512") and 4.5 mm (0.177").3. Position the jack on the end of the cable. Push the cable into the crimpingtool so that the jack is inside the crimping hole, and crimp the jack onto theconductor.4. Push the body onto the cable so that the braid is outside the thinnest part ofthe body.5. Pull the ferrule over the braid onto the body so that the ferrule touches thethick part of the body.
AttachmentsDN99252966 © Nokia Corporation Draft 61 (66)Issue 3-0 en Nokia Proprietary and ConfidentialNote6. Crimp the ferrule onto the body with the crimping tool CS77550.01. Usethe gap '4.52' on the tool.7. Draw the shrinking sleeve over the ferrule and warm it to cause it to shrinkonto the ferrule.Attachment 2: Installation configuration for the Abis 120-ohm interface ofNokia MetroSite.This cable is provided already assembled but is shown here to identify all the partsconstituting an Abis 120-ohm interface.A TQ connector is fitted to both ends of the cable. The wires connecting the TQconnectors are coloured as follows (see figure): OUT+ (pin 4): White stripe OUT- (pin 3): White IN+ (pin 2): Blue stripe IN- (pin 1): Blue
Solution Accessories62 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enAttachment 3: Installation instructions for the AC power plug for NokiaMetroSite.The power feeder is a flexible rubber insulated cable with three multi-wireconductors having dimensions of: 1.5 mm2 or 2.5 mm2 (AWG 15.5-13.5).For installation the following listed tools are needed:• Screwdriver (flat)• Screwdriver (Philips)
AttachmentsDN99252966 © Nokia Corporation Draft 63 (66)Issue 3-0 en Nokia Proprietary and ConfidentialInstructions:1. Strip the power feeder cable from its main insulation 20 mm (0.787").2. Strip the inner conductors and cut them so that the blue and brown wiresare 20 mm (0.787") long and the yellow/green wire is slightly longer, at 25mm (1"). The stripped area is 4 mm (0.157") long.3. Undo the screw holding the body parts together and store the screw, nut andwasher in a safe place. Separate the two parts of the body.4. Remove the sleeve then feed the cable (exposed end) through the sleevefrom the rear.5. Pull the cable through sufficiently to enable the wires to be attached to theplug connectors.
Solution Accessories64 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0enNote6. Undo each plug connector screw sufficiently to enable the cable wire to beinserted and insert the wires in each connector.The brown (live) wire to be inserted in the right-hand connector as viewed fromthe front. The blue (neutral) wire is inserted into the left-hand connector, and theyellow/green (earth) wire to the centre connector.7. Tighten each screw in turn to fix the wires in the connectors.8. Align the sleeve on the cable so that the raised end can be inserted into theslot.9. Place the two body parts together, making sure they are aligned, the wiresare clear of the body fixing hole and the sleeve is properly located in theslot.10. Fix the body parts together with the screw, nut and washer.11. This procedure is to be repeated for the other end of the cable if the powercable is to connect the MetroSite BBU to a MetroSite BTS.If the cable is to be connected to a MetroHub, repeat steps 1 and 2 for theother end of the cable. Connect that end to the MetroHub as described inthe MetroHub User Manual (Installation).If the cable is to be connected to the mains power source then this is userdefined.Attachment 4: Installation instructions for the DC power plug for NokiaMetroSiteThe power feeder is a flexible rubber insulated cable with three multi-wireconductors having dimensions of: 1.5 mm2 or 2.5 mm2 (AWG 15.5-13.5).
AttachmentsDN99252966 © Nokia Corporation Draft 65 (66)Issue 3-0 en Nokia Proprietary and ConfidentialInstructions:1. Strip the power feeder cable from its main insulation 'X' mm (TBA).2. Strip the inner conductors and cut them so that they are of equal length.3. Strip each wire insulation to 'Y' mm (TBA) length using a sharp blade,taking care not to cut any strands of wire.4. Insert each wire, in turn, into a contact and using the crimping tool, crimpthe contact around the wire.5. Undo the cable clamp to enable the cable to be inserted.6. Push the contacts into the connector in their correct positions.It is veryimportant that the contacts are in the correct order in the connector.7. If the cable is to connect the DC supply to a MetroSite BTS, the procedureis to be repeated for the other end of the cable. If the cable is to connect theDC supply to a MetroHub, refer to the MetroHub User Manual(Installation)for the connection of the other end of the cable.
Solution Accessories66 (66) © Nokia Corporation Draft DN99252966Nokia Proprietary and Confidential Issue3-0en

Navigation menu