Nolangroup S p A NCOM5 Motorcycle helmet communication system with BT transceiver User Manual 2 B1v03 ENG

Nolangroup S.p.A. Motorcycle helmet communication system with BT transceiver 2 B1v03 ENG

user manual

Firmware Version: 1
.x
x
EN
USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N
-
Com product.
N-
Com
B1
was made using the most advanced technologies and
the best materials. Long-running tests and thorough system
development have allowed the highest audio quality to be
achieved.
For additional information about
B1
, and to download high-
definition instructions as well as the latest
Firmware
version, visit
the website
www.n
-
com.it
REFERENCE STANDARDS
The products of the N
-
Com line are in compliance with standards as per the table
below:
B1
The Bluetooth system complies with the main safety
requirements and other applicable provisions of Directive
99/5/CE
, Directiv
e
2002/95/CE
, Directive
2002/96/CE
Battery
charger
Directive
2006/95
,
2004/108
,
2002/95/CE
,
2002/96/CE
,
2009/125/CE
Battery
Directive
2006/66
The Declarations of Compliance can be downloaded from the website
www.n
-
c
om.it
(Download section).
FccID
:
Y6MNCOM5
N21550
Bluetooth is a registered trademark property of Bluetooth SIG, Inc.
B1
3
Contents
1.
WARNINGS AND SAFETY
........................................................
4
1.1.
Road safety
...........................................................................
4
1.2.
Switching on the system in safe environments
............................
4
1.3.
Interferences
.........................................................................
4
1.4.
Appropriate use
.....................................................................
4
1.5.
Qualified personnel
................................................................
. 5
1.6.
Accessories and batteries
........................................................
5
1.7.
Disposal
................................................................................
6
2.
CONTENT OF THE PACKAGING
................................................
6
3.
INSTALLATION
.......................................................................
7
3.1.
Installing the microphone
........................................................
9
3.2.
Connecting the battery
...........................................................
10
3.3.
Installing the system on the helmet
.........................................
11
4.
REMOVING THE SYSTEM
.......................................................
14
5.
SYSTEM
CHARACTERISTICS
.................................................
14
5.1.
Basic functions
......................................................................
15
5.2.N-
Com Wizard
......................................................................
15
6.
PAIRING UP BLUETOOTH DEVICES
.......................................
15
6.1.
Affiliation reset function
.........................................................
16
7.
MOBILE PHONE FUNCTIONS
.................................................
16
8.
GPS SATELLITE NAVIGATOR FUNCTIONS
.............................
16
9.
BLUETOOTH A2DP MUSIC PLAYER
........................................
17
10.
AUDIO DEVICES
WITH CABLE CONNECTION
........................
17
11.
RIDER
-
PASSENGER INTERCOM MODE
..................................
18
11.1.
Intercom affiliation
..............................................................
18
11.2.
Intercom function
................................................................
18
12.
BATTERY
..............................................................................
19
12.1.
Battery discharged signal
......................................................
19
12.2.
Recharging the system
.........................................................
19
13.
SUMMARY TABLE OF CONTROLS
...........................................
20
14.
LIMITED WARRANTY
............................................................
21
14.1.
Warranty coverage
..............................................................
21
14.2.
Exclusions and limitations of the coverage
...............................
21
14.3.
Validity of this limited warranty
.............................................
21
14.4.
Procedure for the forwarding of claims
....................................
22
14.5.
Product identif
ication
...........................................................
22
15.
WARRANTY REGISTRATION FORM
.......................................
23
B1
5
1.
WARNINGS AND SAFETY
Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you
will be using with the N
-
Com
B1
. Read the simple rules listed below. Failure to comply with
these rules may lead to dangerous situations.
Caution
: The product cannot be used in official or non-official competitions, motordromes,
circuits, racing tracks an
d the like.
Caution
: Installation of the N-
Com
B1
system results in a weight increase of
approximately
110
g, which is added to the weight of the helmet and of the other
accessories.
Warning
: The electronic components of the N
-
Com system mounted inside th
e helmet are
not waterproof. Consequently, make sure the inside of the helmet, including the
comfort padding, does not get wet in order to avoid damage to the system. If it does,
remove the N-Com system and the helmet comfort padding and let it air dry.
Di
sconnect the battery connector and let it dry as well.
1.1.
Road safety
Always obey all Traffic Regulations in force. While riding the motorcycle, your hands should
always be engaged in actually riding the vehicle. Any operation to the N-Com system must
be car
ried out with the vehicle stopped.
Specifically:
Set your cell phone on automatic answer (see the cell phone instructions to do this).
If your cell phone is not equipped with this function, first stop your vehicle in a safe
area, in compliance with Traffic
Regulations and then answer the call.
Do not make any calls while riding. Stop your vehicle in a safe place in compliance
with Traffic Regulations, and then make the call.
Adjust the volume so that it does not cause a disturbance or distraction while ridi
ng
and at the same time allows you to distinctively hear background noises.
Do not operate your cell phone or other devices connected to N-Com while riding
your motorcycle.
In all cases, obey the Traffic Regulations and remember that riding the motorcycle
has absolute priority over any other maneuver.
1.2.
Switching on the system in safe environments
When using the N-Com system, comply with all limitations and instructions related to
the use of cell phones.
Do not turn on your cell phone or the N-Com system whenever their use is forbidden
or when the devices can cause interference or dangerous situations.
Turn off while refueling. Do not use the N-Com system in filling stations. Do not use
the device near combustible materials or chemical products.
Turn off in
proximity to explosive materials.
1.3.
Interferences
All phones and devices with wireless signal transmission are subject to interferences that
may affect the performance of the device connected to them. These interferences are not
ascribable to a defect of th
e N
-
Com system.
1.4.
Appropriate use
Use the device only in the normal position, as described in the product documentation. Do
not attempt to disassemble, tamper with or modify any part of the N
-
Com system.
B1
5
Caution
: Adjust the volume of the N-Com system (where provided) and of the audio
sources connected to it before you use the system on the road.
Caution
: Adjusting the volume to very high levels may cause damage to your hearing.
Caution
: Adjust the volume of the N-Com system (where provided) and of the audio
sources connected to it so as to avoid audio reproduction at high volumes. Constant
exposure to high audio volumes may damage your hearing.
Caution
: An incorrect installation of the system in the helmet may alter the aerodynamic
and safety characteristics of the helmet itself, thus creating dangerous conditions.
Install the N-Com system according to the instructions provided in the product
documentation. In case of doubt, please contact your local N
-
Com dealer.
Warning:
Listening to other equipment sh
ould not interfere with driving the vehicle, which
must be the top priority at all times. Carry out all operations on the electronic
equipment and on the N-Com system with the vehicle stopped, in compliance with
Traffic Regulations.
1.5.
Qualified personnel
Only qualified personnel can carry out technical assistance on this product. In case of
any malfunction, always turn to your local dealer.
The helmet is a safety device. Tampering with it and/or with the electronic system
inside the helmet, in addition to invalidating the product warranty, can also lead to
dangerous situations.
1.6.
Accessories and batteries
Only use the type of batteries, battery chargers and accessories approved by Nolan
for the specific model.
The use of a battery type different from the recommended one may lead to
dangerous situations and invalidate the warranty.
Contact your local dealer to see about the availability of approved accessories.
When disconnecting the power supply cable of any accessory or of the battery
charger, always grab an
d pull the plug not the cable.
Do not use batteries for purposes other than the prescribed ones.
Never use batteries or battery chargers that turn out to be damaged.
Do not short
-
circuit the battery.
Keep the battery at a temperature between 0 ° / + 4 5° C (
ch
arging
) ; -2 0° / + 6 0
°C
(in use
).
Danger of fire or explosion: do not throw the batteries into a fire nor expose them to
high temperatures!
Do not throw out batteries together with household refuse. The batteries should be
disposed of in compliance with lo
cal regulations
Do not wear the helmet while the battery is recharging.
The helmet should never be left within the reach of unsupervised children in order to
prevent damage to their health caused by access to the batteries.
Battery
Lithium Ion593847
3,7V
800mAh
AK00G
-
0500040VU
100/240v
50/60 Hz 5V
0,4 A
Batterycharger
S-
TR
-
038
100
-
240V
-
60/50Hz 0.1A
6
1.7.
Disposal
Refer to this user manual and to manuals related to other parts of the N-Com system in
order to disassemble the system from the helmet. Once the system has been
disassembled, dispose of it according to the following instructions:
The presence of a crossed-out wheelie bin indicates that in the European
Union the product is subject to separate collection at the end of its useful
life (Eur
opean Directive 2002/96/EC).
Do not dispose of these products together with undifferentiated urban
waste.
The proper disposal of obsolete equipment contributes to preventing possible negative
consequences on people s health and on the environment.
For more detailed information on the disposal of obsolete equipment, contact your
municipality, a waste disposal service or the store where the product was purchased.
2.
CONTENT OF THE PACKA
GING
The N
-
Com
B1
package contains:
e-
box
B1
Electronic plate
PC
connection cable
M
icrophone
Rechargeable battery
Battery charger
Battery holder
Key and screw
Clamp
Microphone
-
Stop
Adhesive
Velcro pads
B1
7
3.
INSTALLATION
Fig. 1
Fig. 2
Fig. 3
Remove the N-Com protection plate
located on the helm
and open the helmet chin guard (flip
up helmets).
Remove the right and left cheek pads
from the helmet (see specific
instructions provided in the user
manual of the helmet).
Remove the Noise Reducers from the
two cheek pads, and tear off the pre-
cut plastic (if equipped).
Fig. 4
Fig. 5
Fig. 6
Remove the back of the comfort
padding by pulling on the neck roll
until it separates from the shell (Fig.
4).
Temporarily put the padding on the
outside of the helmet (Fig. 5).
Remove the N-Com cover from the
helmet border gasket. Push from the
inside of the helmet to facilitate the
removal (Fig. 6).
8
Fig. 7
ONLY FOR FULL
-
FACE HELMETS
Remove the chin guard by pulling on
the special red tab.
Fig. 8
Remove the right and left polystyren
e
cheek pads by gently pulling them out
of the helmet. The helmet shell can be
opened slightly to facilitate the
removal of the cheek pad
.
Caution
: In case the polystyrene cheek
pad is damaged during this operation,
turn to your local dealer for its
repl
acement.
B1
9
3.1.
Installing the microphone
JET HELMETS OR FLIP
-
UP
HELMETS
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Prepare the microphone by inserting the
microphone clamp, being careful to position it
properly (Fig. 9
)
Note
: the flat part of the clamp must be facing
upward when the microphone is positioned as
shown in figure 11
.
Position the microphone in its support as
shown in figure 10, being careful that the
fluorescent clamp is facing toward the inside of
the helmet.
Insert screw and washer in the micro
phone
clamp; use the key to screw in the microphone
securing screw to the shell frame.
FULL
-
FACE HELMETS
Fig. 13
Fig. 14
Take the polystyrene cheek pad (left-hand side) and position the microphone in
its
housing, as shown in fig. 13, making sure that the fluorescent band stays facing the
inside of the helmet.
(Fig. 14
)
10
3.2.
Connecting the battery
Only for Jet helmets or
flip
-
up
helmets
:
Fig. 15
Fig.
16
Hook up the battery cable (Red+Black) to the connector located on the wiring system
(Fig. 15
).
Insert the battery in its holder, first positioning the side equipped with the cables
outlet, keeping the cables un
derneath the plastic tab (Fig. 16
).
Fig.
17
Fig.
18
Insert the connectors set in the cable-stop guide located on the side of the battery-
holder (Fig. 17 and 18
).
Only
for full face helmets
:
Fig.
19
Position the battery in the right
polystyrene cheek pad housing
(Fig.
19
).
B1
11
3.3.
Installing the
system
on the helmet
Fig. 20
Position the
system
inside the helmet as shown in figure 20, next to the N-Com housing
in the shell
.
Fig. 21
Looking at the helmet from the outside,
slide the rear positioning tab into
groove A as shown in the figure;
Press in the area marked PUSH from
inside the helmet until the f
astenin
g
clasp B clicks (Fig. 21
).
Fig. 22
Pull out the connectors area from the
helmet gasket: the gasket will have to
be slightly deformed to facilitate the
insertion.
12
Fig. 23
Fig.
24
Insert the microphone connector in
the
micro USB
electronic plate
.
Before you place the speaker in its housing, apply the Velcro pad to the polystyrene
cheek pad (Fig.
24
).
Fig.
25
Position the loudspeaker in the special
housing obtained in the polystyrene cheek
pad (Fig. 25
).
Fig. 26
Replace the polystyrene cheek pad (left
side), positioning the cable in the
groove that you see in the cheek pad
(Fig. 25
).
Note:
Make sure the cheek pad is properly
positioned in its housing, pushing in
the lined corner underneath the ribbing
on the shell (Fig. 26
).
B1
13
Fig.
27
Only
for Jet helmets or flip
-
up helmets
Secure the battery-holder support to
the right side of the helmet, lining up
the holes with the pins on the shell
(Fig.
27
)
Before you place the speaker in its housing, apply the Velcro pad to the polystyrene
cheek pad
(right side).
Position the loudspeaker in its housing obtained in the polystyrene cheek pad (right
side).
Replace the polystyrene cheek pad (right side), positioning the cable in the groove you
see in the cheek pad.
Fig. 28
O
nly for full
-
face helmets
Insert the chin guard (microphone side),
gently
placing the microphone in its
housing. Then press down on the red tab
until the chin guard is locked in place on the
helmet.
(Fig. 28
)
Fig. 29
Fig. 30
Position the comfort padding in its housing (see specific instructions provided in the
helmet user manual), hooking the neck roll (Fig. 29).
14
Position both the comfort cheek pads in their housing (see specific instructions
provided in the helmet user manual) making sure that all the press
-
studs click.
Not
e: Carefully check the proper final positioning of the cheek pad, pulling the chinstrap
toward the inside of the helmet and testing the press
-
studs.
Caution:
Make sure that there are no cables sticking out of the helmet and that the
loudspeakers are in the
ir housing.
Caution
: Always verify the proper length of the chinstrap and adjust it as necessary, once
again referring to the specific helmet instructions.
Position the e-box in the relevant housing. First insert the front part, then press down
on the e-box until both hooks fully click. To remove the e-box, press the two sliding
hooks at the same time until the e
-
box comes out.
Warning
: Do not leave the helmet exposed to atmospheric agents without the e-box or
the protection plate provided with the helme
t.
4.
REMOVING THE
SYSTEM
Fig. 31
To remove the
system
from the helmet,
remove the earphone and the comfort
cheek pads as shown in the assembly
operations. Then remove the polystyrene
cheek pads. Remove the protection plate,
then, looking at the helmet from the
outside, release the connector by acting on
the fastening clasp as illustrated in the
figure.
After releasing the connector from the shell, also remove the right part by releasing the
battery holder
.
Now remove the entire
system
from the helmet.
5.
SYSTEM CHARACTERISTI
CS
N-
Com
B1
allows wireless connection to a mobile phone, a satellite navigator, and an MP3
A2DP player using Bluetooth technology.
The system can also be used for wireless intercom communication between two helmets,
if
both helmets
are equipped with a N
-
Com
Bluetooth system
.
The system can be expanded by means of a
USB
Multimedia Wire accessory (
sold
separately
)
, which is used for cable connection to multimedia sources.
B1
can be managed, updated and customised using the N-
Com
Wizard
programme, which can be downloaded from the Download section of the
Internet site
www.n
-
com.it
B1
15
5.1.
Basic functions
All N
-Com system functions are available through the operation of three pushbuttons: ,
on
and
. Every time the system is given a command, a special acoustic signal can be
heard, which varies depending on the function being requested. This way, all the functions
can be used while wearing the helmet.
The type of command given to the system dep
ends on how long the pushbutton is pressed.
System ON
Press
on
and keep it pressed for about 2 seconds, until the
LEDs turn on and you hear a beep in the headset.
System OFF
Press
on
and keep it pressed for about 4 seconds, until the
LEDs turn off and you hear a beep in the headset.
Increase Volume
Briefly press to increase the volume. A double tone signals
the highest volume level.
Decrease Volume
Briefly press to decrease the volume. A double tone signals
the lowest volume level.
5.2.
N-
Com
Wizard
N-Com Wizard is the PC application that can be used to manage and
configure the
B1
system.
The programme can be downloaded from the Internet site
www.n
-
com.it
, in the
Download section. In order to use it, a helmet equipped with
B1
must be connected to
the PC, using the USB cable supplied with the system.
N-
Com Wizard allows you to customize your
B1
, specifically:
Setting the system audio levels
Update the device firmware
The programme includes an on-
lin
e guide that explains how it works (after installing it on
your PC, press F1 to display this guide).
6.
PAIRING UP BLUETOOTH
DEVICES
In order for
the
B1
system
to be connected to another Bluetooth device, the latter needs
to be first
paired up
with the N
-
Com
system.
The pairing up procedure is the same for all Bluetooth devices: mobile phones, MP3
Bluetooth players, satellite navigators, etc.
1.
Make sure the
B1
is turned off;
2. Press
on
and keep it pressed (for more than 6 seconds), until the LEDs start to
fla
sh quickly and you hear a sharp beep in the headset, indicating the Pair-
up
mode ;
3. On the Bluetooth device, turn on the search for Bluetooth devices (refer to the
instructions manual of your device for the proper pairing up procedure, as it
varies dependi
ng on the brand and model of the device);
4. After a few seconds, the
device
will display the name N-
Com
B1
v.X.XX ,
followed by the manufacturer s identification data;
5.
Select the N
-
Com device. If a password is requested, enter
0000
(four zeros);
6.
B1
will confirm the pairing up by means of a tone in the headset, and the LEDs
will stop flashing;
7.
Turn off and on both the
device
and the
B1
to store the pairing up data.
N
ote
: The affiliation is stored in the helmet and in the cell phone and it is not lost when
th
e two devices are turned off. As a result it needs to be carried out only once.
16
Note:
If a Bluetooth device (mobile phone or GPS) equipped with music player with
Bluetooth A2DP player has already been paired up, the pairing up DOES NOT have to
be repeated
as the A2DP protocol has already been stored in the
B1
.
Once the Bluetooth device has been paired up, connection is automatic when the system is
turned on.
6.1.
Affiliation reset function
You can remove all affiliated devices from the system memory. This operation is not
reversible; right after resetting, you will have to repeat the affiliation procedure for the cell
phone (or for other compatible Bluetooth devices).
To erase all devices previously affiliated, proceed as follows:
Press
on
and keep it pressed (for more than 4 seconds), until the LEDs start to flash
quickly and you hear a sharp beep in the headset, indicating the Pair-up mode ;
Press and at the same time for 4 seconds, and release them when you hear a
beep
. The N-Com will emit a special acoustic signal to confirm and will then turn itself
off.
This function can also be turned on through PC using the N-Com Wizard
programme.
7.
MOBILE PHONE FUNCTIO
NS
Answering a phone
call
Briefly press any key when you hear the incoming call signa
l
Hanging
up/rejecting a
phone call
Press
on
and keep it pressed for about 2 seconds (until you
hear the acoustic signal)
Voice call (if
equipped)
Press
on
and keep it pressed for about 2 seconds (until you
hear the acoustic signal)
Redial last nu
mber
Briefly press and at the same time
Transferring a call
from helmet to
mobile phone
To transfer an ongoing call from the helmet to the mobile phone,
press both and at the same time and keep them
pressed for 4 seconds
Conference call
function
B1
allows a conference call with
Rider
and
Pillion Passenger
.
When a call comes in on a mobile phone connected via Bluetooth to
B1
, the
Rider
-
Pillion
Passenger
intercom is temporarily turned off. However, if you wish to share the phone call
with
the other helmet, simply turn on the intercom manually during the phone call
(by
briefly pressing
on
).
Caution
: this function is available only if the
Pillion Passenger
helmet is also equipped with
a N
-
Com system provided with the same function.
8.
GPS
SATELLITE NAVIGATOR
FUNCTIONS
B1
is compatible with the most common satell
ite navigators for motorcycles.
By connecting the N-Com system to the GPS, all instructions will be transferred to the
helmet.
Every time the navigator communicates instructions, the intercom via Bluetooth with the
Pillion Passenger
is cut off and automatically restored at the end of the communication.
B1
17
Note
: If the navigator is pre-set for connection to a Bluetooth mobile phone, you will be
able to receive the phone call audio directly in the helmet through the GPS. In this
case, you can answer the call directly from the navigator.
GPS Conference Call Function
The Conference function allows you to keep the Rider-Pillion Passenger intercom open
even while the satellite navigator is
giving instructions, thus preventing the intercom mode
to be turned off every time the navigator gives instructions.
Caution
: this function is available only if the
Pillion Passenger
helmet is also equipped with
a N
-
Com system provided with the same funct
ion.
At the end of the GPS communication, the intercom with the second helmet stays open and
the "Conference" setting is stored for future GPS communications.
9.
BLUETOOTH A2DP MUSIC
PLAYER
You can listen to high quality music by connecting
B1
to a device equipped with Bluetooth
A2DP (Advanced Audio Distribution Profile) protocol.
The
B1
system is also equipped with Bluetooth AVRCP (Audio Video Remote Control
Profile) protocol, which allows you to stop and resume music reproduction directly from the
hel
met (with devices equipped with AVRCP).
Connection to A2DP music
player
The connection is automatic when you turn on the
system
.
Wait a few seconds for the connection
.
Play music (Play)
Press the button and keep
it pressed for 2 seconds.
Pause funct
ion (Pause)
When the player is connected and playing music, press
for 2 seconds.
Next track (Skip)
When the player is playing music, press for 4 about
seconds.
Stop playing music (Stop)
Press for 2 seconds.
Note
: The Bluetooth intercom does
not work while listening to an A2DP audio source or an
un Mp3 player connected via cable.
10.
AUDIO DEVICES WITH C
ABLE CONNECTION
N-
Com B1 allows connection via cable (sold separately) to audio sources equipped with the
3.5mm output generally used by these
devices for the headsets.
To listen to the audio source, connect the cable to the helmet using the micro-USB port,
then start playing the audio file on the device, then activate the audio peripheral device
using the specific key.
You can turn on or off l
istening in the helmet by pressing the key for 2 seconds.
N.B.
: You cannot stay connected in intercom mode with the pillion passenger while using
the audio source via cable.
18
11.
RIDER
-
PASSENGER INTERCOM M
ODE
In order to use
B1
in wireless intercom mod
e, both helmets have to be equipped with a
N-
Com Bluetooth system
.
In order for two N-Com systems to communicate with one another, they have to be paired
up first.
11.1.
Intercom affiliation
1.
Make sure both N
-
Com Bluetooth systems are turned off;
2.
Set both N
-
Com
Bluetooth systems in Pairing up mode by pressing
on
(for more than
4 seconds), until the LEDS start to flash quickly;
3. On either one of the two helmets, press
on
briefly;
4. After a few seconds, the helmets recognize each another, a beep is emitted to s
ignal
the pair up was successful and intercom communication is activated;
5. Turn off both N-Com Bluetooth systems and turn them back on to store the pair up
data.
11.2.
Intercom function
To activate the intercom connection, turn on the two N-Com systems and
brief
ly
press
on
on one of the helmets.
I
ntercom activation
With
B1
turned on, briefly press
on
.
I
ntercom deactivation
With
B1
turned on, briefly press
on
.
B1
19
12.
BATTER
Y
Before using the N-Com device for the first time, recharge the battery completely for at
least 10 hours. To obtain best performances from the battery, it is recommended to
completely recharge the battery the first few times. Afterwards, you can recharge the
battery for shorter periods. Whenever possible, it is best to recharge the battery
completely.
12.1.
Battery discharged signal
When turned on, the system signals when the battery is running down by switching to the
Reserve
mode.
When the battery charging power falls below 1 hour of operation, the buttons and
start to flash in order to indicate that the system is in
Reserve
mode. Three consecutive
beeps also signal the reserve mode.
When the battery operates in Reserve , the system automatically turns itself off in case
no button is pressed for 30 minutes. The shutting off is sig
naled by a series of beeps in the
helmet. This function makes it possible to always have a small reserve of energy to use it
again in case you forget to turn off your helmet.
12.2.
Recharging the system
To recharge the
B1
system, connect the USB cable to a battery charger or to a powered
USB port. Charging occurs as follows:
B1 system turned off
When you connect the
B1
system to the battery
charger, the blue LED begins to flash.
When the battery is fully charged, the blue LED stops
flashing and stays on.
B1
system turned on
When you connect the
B1
system to the battery
charger, the red LED begins to flash.
When the battery is fully charged, the red LED turns off.
N.B.
: If the device has not been charged for a long time (a few months), it may not be
possib
le to turn on the system during the first few minutes of the charging, as the
voltage may drop below the minimum limit.
20
13.
SUMMARY TABLE OF CON
TROLS
Button
on
on
Pres
sure
Brief
Long
Brief
Long
Brief
Long
Brief
Long
Turning on
X
(3s)
Turning off
X
(4s)
Increase Volume
X
Decrease Volume
X
Activate
/
Deactivate
audio via cable
X
(2s)
Activate
intercom
X
Basic Functions
Deactivate
intercom
X
Answer phone call
X
X X
Voice call
X
(2s)
Hang up/reject a
phone call
X
(2s)
Redial last number
X
Mobile phone
connection
X
(2s)
Mobile phone
disconnection
X
(4s)
Call transfer
X
(4s)
Bluetooth peripheral
Activate Conference
Mode
X
Connect A2DP device
X
(2s)
Disconnect A2PD
device
X
(2s)
Play music (Play)
X
(2s)
Pause Function
(Pause)
X
(2s)
Mp3 player
Next track
(Forward)
X
(4s)
Pairing up mod
e
-
system turned off
X
(4s)
Rider
-
Passenger
intercom pair up
X
Setting
Erase pair ups
**
X
( 4
s)
*
Briefly press at the same time
**
With N
-
Com system in Pairing up Mode
B1
21
14.
LIMITED WARRANTY
With this LIMITED WARRANTY CERTIFICATE,
Nolangrou
p warrants this Product to be free from defects
in material and workmanship at the time of its original purchase by the buyer.
We invite you to:
-
Read the cautions pertaining to safety and proper use.
-
Read the warranty terms and conditions.
- Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these
cases, the product has to be taken back to the dealer where it was purchased.
14.1.
Warranty coverage
If any defect covered by this limited warranty certificate is discovered within 2 (two) years from the
purchase date shown on the tax receipt,
Nolangroup
shall repair or replace the defective product
through its distribution network after having verified the defect.
Nolangroup
shall supply all the material
and labor that is reasonably required to remedy the defect, except in those cases where the damage is
caused by one of the items listed in the following paragraph Exclusions and limitations of the
Coverage .
14.2.
Exclusions and limitations of the coverage
This warranty only covers defects in materials and manufacturing.
Nolangroup
shall not be considered
responsible for product defects that can be attributed, either partially or in full, to any other cause,
including but not limited to:
Defects or damages resulting from usin
g the Product in conditions that differ from the usual ones.
Damages caused by improper use not conforming with normal operation in accordance with the
product operating and maintenance instructions provided by
Nolangroup
.
Negligence and normal wear of int
ernal and external parts.
Any damage caused by an accident;
Any change or modification made to the helmet or to the N-com system by the user or by third
parties.
Color changes or damages caused by exposure to harmful chemical products.
The use of incompati
ble accessories that are not part of the N
-
Com product range.
Moreover, the warranty does not cover product defects caused by fortuitous events, modifications or
adjustments, causes of force majeur or damages deriving from the product coming in contact wit
h
liquids.
The internal helmet components are not and cannot be waterproof. Consequently, any improper
exposure to rain, humidity, food spillages or other liquids can result in damages to the N
-
Com electronic
devices, damages for which Nolan
group
shall not
be responsible.
This warranty does not include those parts subject to wear and tear such as, for example, the
rechargeable battery and the cables used for connection between the various N-Com systems or
between the N
-
Com systems and other devices.
Since
N
olangroup
does not supply the system on which the cell phones work, it shall not be
responsible for the operation, availability, coverage, services or range pertaining to the aforementioned
system.
Whenever the product is used in conjunction with accessories or equipment not supplied by
Nolangroup
,
Nolangroup
shall not guarantee proper operation of the product/device combination, nor
will it accept requests for repairs or replacements under warranty in case the product is used in such a
way.
Nolangroup
shall not be responsible in case the product presents limited capabilities due to the
operating mode of cell phones or of other accessories or equipment not supplied by
Nolangroup
.
Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate the
warranty.
Moreover, the defects covered by this warranty do not include all those specific and subjective
situations that may come up during the active use of the helmet such as, for example, comfort
problems while riding or aero
dynamic noises.
Nolangroup
shall not be held responsible in any case for incidental or consequential damages (including,
without any limitation whatsoever, damages to one or more persons) resulting from non-fulfillment of
the obligations arising from this
warranty as it pertains to
Nolangroup
products.
14.3.
Validity of this limited warranty
This warranty is valid only if the enclosed warranty form is duly and completely filled out with the
following information:
Product identification code
22
Name and stamp of th
e authorized dealer.
Product purchase date.
Buyer s name and address.
Nolangroup
reserves itself the right to not carry out repairs under warranty if the aforementioned
information is removed or modified after the original purchase of the product from the
dealer.
14.4.
Procedure for the forwarding of claims
To forward a claim covered by this warranty, the buyer has to directly notify the dealer where the
helmet was purchased with regards to the defect, presenting at the same time the defective product, a
copy o
f the sales receipt and the Warranty registration form, duly filled out as instructed above.
PRIOR TO CONTACTING THE DEALER, WE RECOMMEND THAT YOU READ CAREFULLY THE USER
MANUAL ENCLOSED WITH THE PRODUCT.
AFTER 2 (TWO) YEARS FROM THE DATE OF PURCHASE, THIS LIMITED WARRANTY IS VOID FOR ALL
EFFECTS AND PURPOSES.
Repairs or maintenance under warranty do not extend the period of the warranty itself. Therefore, in
case the product or one of its components is replaced, this does not initiate a new warranty period, as
the purchase date of the original product shall be taken into account for warranty purposes.
Only for repairs or replacement of electronic components, in the event that
Nolangroup
proceeds to
repairing or replacing the product, said product shall enjoy a warranty period equal to the residual
portion of the original warranty or ninety (90) days from the repair date (the longer period being
considered).
The repair or replacement can be carried out even with regenerated components with equivalent
functi
ons.
The replaced parts or components shall become property of Nolangroup
.
THIS WARRANTY VOIDS AND REPLACES ANY OTHER WRITTEN OR VERBAL WARRANTIES PROVIDED
FOR BY THE LAW THAT CAN BE DEROGATED AT THE PARTIES WILL; SPECIFICALLY,
NOLANGROUP
DOES NOT GRANT SPECIFIC WARRANTS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. IN NO CASE SHALL NOLAN BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING BUT NOT LIMITED TO LOST PROFITS OR COMMERCIAL DAMAGES, TO THE FULL EXTENT
THOSE DAMAGES CAN BE DISC
LAIMED BY THE LAW.
NOLANGROUP
RESERVES ITSELF THE RIGHT TO MODIFY, AT ANY TIME AND WITHOUT ADVANCE
NOTICE, THE PRODUCT CHARACTERISTICS, FUNCTIONS, COMPATIBILITY AND SOFTWARE.
Some Countries do not allow the exclusion or limitation of incidental or consequential damages, or the
limitation of the duration of implied warranties; as a result of this, the previous limitations and
exclusions may not be applicable to you.
This warranty does not have any effect on the customer s legal rights under the national jurisdiction in
force or on the consumer s rights towards the dealer sanctioned by the purchase/sale contract.
This warranty is valid throughout the European territory, and it represents the only express warranty
provided by
Nolangroup
in relation to the sale of its own products. This warranty does not affect the
rights to which the buyer is entitled and which are expressly provided for by Directive 1999/44/CE.
This warranty does not affect the consumer s rights provided for by the law, and specifically by t
he
provisions of Legislative Decree 2 February 2002 n. 24.
14.5.
Product identification
N-Com products are identified by means of a code that allows product
traceability and identification.
The identification code is found underneath the bar code printed on
th
e product packaging.
15.
WARRANTY REGISTRATIO
N FORM
Product name:
B1
Identification code
Buyer s I nform ation
Name
Last name
Address
Phone
e-
mail
Dealer s stam p
Date of purchase
Printed on recycled paper
B1
-
16/10/2012
9.28.00

Navigation menu