Nortek Security and Control 2GIG FT1345 Flood and Temp Sensor User Manual 10008993A indd
2GIG Technologies, Inc. Flood and Temp Sensor 10008993A indd
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3036694 |
| Application ID | 74mPCiGmuZsZYtiYbLkVRg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 56.66kB (708254 bits) |
| Date Submitted | 2016-06-22 00:00:00 |
| Date Available | 2016-06-22 00:00:00 |
| Creation Date | 2016-03-23 07:34:35 |
| Producing Software | Acrobat Distiller 10.1.16 (Windows) |
| Document Lastmod | 2016-03-23 07:35:49 |
| Document Title | 10008993A.indd |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | Copyright © 2016 Nortek Security & Control |
PRINTER’S INSTRUCTIONS: INSTR,INSTL,2GIG-FT1 TEMP FLOOD SENSOR - P/N: 10008993 A- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5000” X 11.000” - TOL. +/- 0.125”- SCALE: 1-1 - PAGE 1 OF 2- FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING 2GIG-FT1-345 FLOOD AND TEMPERATURE DETECTOR Figure 2. Opening Sensor Case 1. PUSH DOWN ON THUMB TAB. INSTALLATION INSTRUCTIONS The 2GIG-FT1-345 is a fully supervised, tamper protected one-way 345 MHz sensor. It will monitor the ambient temperature and/or will detect a wet/dry flood condi on. The sensor reports wet/dry condi ons and temperature to the panel. Flood Conditions Once the sensor probe detects the presence of water for three (3) minutes, the integral transmi er will send a wet alarm transmission to the panel. The probe will also send a restore (dry) report when the presence of liquid is no longer detected by the flood probe for three (3) minutes. For flood repor ng the sensor requires the installa on of the supplied external flood probe. The sensor is capable of detec ng clean or dirty fresh water, salt water, or tap water. Temperature Conditions Heat: 2. PULL BACK PLATE OFF OF COVER Grip the base of the sensor case. Place thumb on tab and push down un l sensor case separates. Figure 3. Separate Sensor Case 1. If the temperature is more than 95° F (35°C) for five (5) minutes, the sensor will send a loop 2 transmission. 2. If the temperature is less than 95°F (35°C) for five (5) minutes, the sensor will send a loop 2 clear. REMOVE SENSOR COVER FROM SENSOR BASE Cold: 1. If the temperature is less than 41°F (5°C) for five (5) minutes, the sensor will send a loop 3 transmission. 2. In the temperature is more than 41°F (5°C) for five (5) minutes, the sensor will send a loop 3 clear. Contents Figure 4. Installing New Ba ery Verify that the package includes the following: • 1—2GIG Flood/Temperature Sensor • 1—Sensor Mounting Plate • 1—3V Lithium Battery ( Panasonic CR15H270 uninstalled) • 3—3/8” Phillips Screws • 1—Double Stick Tape Strip • 1—Probe Mounting Plate BATTERY BATTERY REMOVAL AND/OR INSTALLATION Installation Tools Required • Phillips Screwdriver Figure 1.Temperature/Flood Sensor Contents Double S ck Tape Strip Sensor Moun ng Plate Probe Moun ng Plate 3V Lithium Ba ery Phillips Screws (3/8”) Flood Probe Cord Flood Probe Transmi er with Integral Temperature Sensor Installing and Replacing Battery Open Sensor Case as show in Figures 2 and 3. Install or replace ba ery. TEMPERATURE/ FLOOD SENSOR BASE Installing a New Battery and System Programming NOTE: Do not install ba ery un l panel is in Sensor Programming Mode. 1. Place panel in Sensor Programming mode 2. Insert ba ery 3. Close sensor Replacement Battery Installation: NOTE: If ba ery has been previously installed 1. Remove ba ery and dispose of (mee ng state regula ons) 2. Wait two (2) seconds 3. Replace ba ery 4. Close sensor Installing/Mounting Flood/Temperature Sensor The 2GIG-FT1-345 Flood and Temperature Sensor includes two methods of installa on: 1. Double S ck Tape Installa on (See Figure 5). 2. Screw/Moun ng Plate Installa on (See Figure 6). It is strongly recommended that the Flood/Temperature Sensor be mounted using screws (provided) and Moun ng Plate (provided). Figure 5. Double S ck Tape Moun ng Sensor Moun ng Plate APPLY DOUBLE STICK TAPE TO BACK OF MOUNTING PLATE FLOOD/ TEMPERATURE SENSOR WALL FIRST PUSH SENSOR ONTO MOUNTING PLATE TABS DOUBLE STICK TAPE MOUNTING STRIP THEN PUSH UP PLATE Copyright ©2015 Nortek Security & Control LLC 1 PRINTER’S INSTRUCTIONS: INSTR,INSTL,2GIG-FT1 TEMP FLOOD SENSOR - P/N: 10008993 A- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5000” X 11.000” - TOL. +/- 0.125”- SCALE: 1-1 - PAGE 2 OF 2- FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING 2GIG Flood & Temperature Control I Instruc on Manual REGULATORY INFORMATION Figure 6. Screw Moun ng Sensor Moun ng Plate MOUNT SENSOR MOUNTING PLATE WITH SCREWS (INCLUDED) SENSOR WALL FIRST PUSH SENSOR ONTO MOUNTING PLATE TABS MOUNTING PLATE THEN PUSH UP Removing Flood/Temperature Sensor from Mounting Plate If Flood/Temperature Sensor needs to be removed from the wall (for changing out ba ery), open sensor case (See Figures 2 and 3). Remove ba ery, then Press Down on release tab with flathead screwdriver and pull sensor UP. Figure 7. Removing Sensor from Wall/Moun ng Plate OPEN SENSOR CASE AND REMOVE BATTERY PRESS DOWN ON TAB IN UPPER LEFT CORNER WITH FLATHEAD SCREWDRIVER THEN PUSH UP ON SENSOR CASE TO REMOVE Mounting Flood Probe The Flood Probe must be mounted at floor level using the Probe Moun ng Plate and screw (included) mount as shown in Figure 8. Figure 8. Moun ng Probe Moun ng Plate at Floor Line This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference in a residen al installa on. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruc ons, may cause harmful interference to radio communica ons. However, there is no guarantee that interference will not occur in a par cular installa on. If this equipment does cause harmful interference to radio or television recep on, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna Increase the separa on between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. Any changes or modifica ons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. Ľexploita on est autorisée aux deux condi ons suivantes: (1) ľappareil ne doit pas produire de brouillage, et (2) ľu lisateur de ľappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscep ble ďen comprome re le fonc onnement. FCC COMPLIANCE STATEMENT This device complies with FCC Rules and Regula ons as Part 15 devices as well as Industry Canada license exempt RSS Rules and Regula ons. Opera on is subject to the following two (2) condi ons: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired opera on. LIMITED WARRANTY This Nortek Security & Control LLC product is warranted against defects in material and workmanship for two (2) years. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control LLC or through Nortek Security & Control normal distribu on channels. Nortek Security & Control does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obliga ons or liabili es on the part of Nortek Security & Control for consequen al damages arising out of or in connec on with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installa on, or reinstalla on. All implied warran es for func onality, are valid only un l the warranty expires. This Nortek Security &Control Warranty is in lieu of all other warran es expressed or implied. FLOOD PROBE INSTALL FLOOD PROBE TO MOUNTING PLATE UNTIL IT “SNAPS” INTO THE SIDE CLIP SCREW FASTENER MOUNT FLOOD PROBE MOUNTING SIDE CLIP PLATE AT FLOOR LINE Flood/Temperature Specifications Opera ng Temperature: 32°to 120° F (0° to 49° C) Opera ng Rel. Humidity: 5 to 95%, non-condensing Opera ng Frequency: 345 MHz Ba ery Type: CR2 3V lithium ba ery Projected Ba ery Life: 5 Years Nortek Security & Control LLC 1950 Camino Vida Roble, Suite 150 Carlsbad, CA 92008-6517 USA For technical support in the USA and Canada: 855-2GIG-TECH (855-244-4832) Email: 2gigtechsupport@nortek.com Visit www.nortekcontrol.com for technical support hours of opera on For technical support outside of the USA and Canada: Visit dealer.2gig.com for a list of distributors in your region 10008993 A 2 Copyright © 2015 Nortek Security & Control
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2016:03:23 07:35:49-07:00 Create Date : 2016:03:23 07:34:35-07:00 Metadata Date : 2016:03:23 07:35:49-07:00 Format : application/pdf Title : 10008993A.indd Creator : Copyright © 2016 Nortek Security & Control Producer : Acrobat Distiller 10.1.16 (Windows) Keywords : Document ID : uuid:d64dd13d-1708-456c-8e81-92e4b8b49a54 Instance ID : uuid:d5d79058-f3ca-4bbe-8e0b-35b11ed369e0 Startup Profile : Print Page Count : 2 Author : Copyright © 2016 Nortek Security & Control Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools