Nortek Security and Control 00178 Alarm Control Panel User Manual 10013635A 1

Nortek Security & Control LLC Alarm Control Panel 10013635A 1

Contents

Cell Module Installation Instructions

Copyright © 2016 Nortek Security & Control LLC 1LTE CELL RADIO MODULEINSTALLATION INSTRUCTIONSThe 2GIG LTE Cell Radio Module is a snap-in, cellular radio module that provides the 2GIG Control Panel with the ability to send and receive two (2) -way voice communicaons with the Central Staon monitoring the security system. It is designed for use with two (2) External Cellular Antennas which provides a consistently strong signal for communicaons.NOTE: For best performance locate the antenna away from metal.In addion to providing the Control Panel the ability to transmit security informaon to online monitoring portals, the cell radio module allows for delivery of Over-the-Air (OTA) firmware updates to the Control Panel. Box ContentsVerify that the package includes the following items:•1—LTE Cell Radio Module•2—External Cellular Antennas•2—#4 Phillips Head Machine Screws and Lock WashersRequirements•2GIG Control Panel with the appropriate firmware version foryour Cell Radio ModuleInstalling the LTE Cell Radio Module and AntennasNOTE: As with all electrical appliances, a shock hazard exists if any electrical current is connected to the 2GIG Control Panel by AC power or baery while inserng, removing, or replacing parts. To install the Cell Radio Module:1Disconnect the AC power supply from its power source. 2Remove the backplate from the Control Panel. 3Disconnect the baery from the Control Panel.4Align the Cell Radio Module as shown in the figure below.5Use the two (2) screws and lock washers provided to secure the Cell Radio Module as shown in the figure below.Figure 1 LTE Cell Radio Module PlacementA = MAIN connector for out-of-panel antenna (in wall or in desk mount)B = DIV connector for in-panel antenna7 Affix both antenna cables to the connectors on top of the Cell Radio Module as follows:NOTE: Both antennas must be installed for proper performance.•Connect one antenna to the MAIN connector and place theantenna outside the case as shown in Figure 2.•Connect the other antenna to the DIV connector and place itinside the case.NOTE: Route the antenna cables so that they do not run across the top of the module.8 Pull the loose end of the antenna through the access hole on the Control Panel’s backplate.Figure 2 Antenna Placement9 Replace the Control Panel’s backplate.Removing an Existing Cell Radio Module and AntennaIf you are replacing an exisng module with a new LTE Cell Radio Module, use the steps below.NOTE: As with all electrical appliances, a shock hazard exists if any electrical current is connected to the 2GIG Control Panel by AC power or baery while inserng, removing, or replacing parts. Removing the Cell Radio ModuleTo remove the Cell Radio Module:1Disconnect the AC power supply from its power source. 2Remove the backplate from the Control Panel. 3Disconnect the baery from the Control Panel.4Detach the antennas as shown in 1 in the figure below. For steps, see "Removing an Internal Antenna" on page 2 or "Removing an External Antenna" on page 2.5Remove the screws as shown in 2 in the figure below.6Pull the Cell Radio Module out carefully, without bending the pins as shown in 3 in the figure below.PRINTER’S INSTRUCTIONS10013635A LTE-CELL-MODULE-INSTALL-INSTR-en-PRT, 09/16/2016, BLACK, 20LB MEAD BOND, 8.5X11”, TOL. +/- 0.125, SCALE: 1:1, FRONT & BACK, FOLD TO FIT BOX6 Attach the provided FCC Label to the control panel back cover.
2 Copyright © 2016 Nortek Security & Control LLCFigure 3 Removing the Cell Radio Module7Plug the new Cell Radio Module into the 2GIG Control Panel by carefully placing it onto the pins. 8Secure the module with the two (2) Phillips Head Machine Screws and Lock Washers. 9Aach both of the new antennas as described in "Installing the LTE Cell Radio Module and Antennas" on page 1. NOTE: If replacing a 3G or CDMA radio, do not reuse the exisng antenna.Removing an Internal AntennaTo remove an internal antenna:1Disconnect AC power supply from power source. 2Disconnect the baery from the 2GIG Control Panel. 3Li up the side flap on the 2GIG Control Panel. 4Detach the antenna.5Pull the internal antenna out from the side of the 2GIG Control Panel. Removing an External AntennaTo remove an external antenna:1Disconnect AC power supply from power source.2Remove the backplate from the Control Panel. 3Disconnect the baery from the 2GIG Control Panel.4Detach the antenna. 5Pull the external antenna from where it was previously installed. 6Replace the back cover on the control panel.Regulatory InformationRegulatory marks are affixed to either the LTE Cell Radio Module and/or its packaging. For regulatory informaon, submit an email request to: 2gigtechsupport@nortek.comLimited WarrantyThis Nortek Security & Control product is warranted against defects in material and workmanship for one (1) year. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control LLC or through Nortek Security & Control LLC’s normal distribuon channels. Nortek Security & Control LLC does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any.There are no obligaons or liabilies on the part of Nortek Security & Control LLC for consequenal damages arising out of or in connecon with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installaon, or reinstallaon. All implied warranes for funconality, are valid only unl the warranty expires. This Nortek Security & Control LLC Warranty is in lieu of all other warranes expressed or implied. For technical support in the USA and Canada:855-2GIG-TECH (855-244-4832)Email: 2gigtechsupport@nortek.comVisit website for technical support hours of operaonFor technical support outside of the USA and Canada:Contact your regional distributorVisit 2gig.com/dealers/ for a list of distributors in your regionPN: 10013635A10 Replace the previous FCC label with the new FCC label on the control panel back cover.

Navigation menu