Nortel Networks 1000E Users Manual Communication Server
1000e 9d0cccfd-0852-44ed-a9b5-b93cb2a8f6fb Nortel Networks Telephone 1000E User Guide |
2015-01-26
: Nortel-Networks Nortel-Networks-1000E-Users-Manual-346506 nortel-networks-1000e-users-manual-346506 nortel-networks pdf
Open the PDF directly: View PDF
Page Count: 490 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- Title page
- Revision history
- Contents
- List of Procedures
- About this document
- Safety instructions
- Installation summary
- System components
- Contents
- Introduction
- CS 1000E Call Server
- Backup and restore enhancements
- New backup rules
- Signaling Server
- Media Card
- Media Gateway
- Media Gateway Expander
- 19-inch Rack Mount Kit
- BayStack 470 Switch
- BayStack 460 Layer 2 switch
- MRV Terminal Server
- 19-inch rack
- System cables
- Miscellaneous system components
- Uninterruptible Power Supply
- Telephones
- Rack-mounting the components
- Contents
- Introduction
- Lifting system components
- Guidelines for component placement in a rack
- Rack-mounting a CS 1000E Call Server
- Rack-mounting a Media Gateway or Media Gateway Expander
- Rack-mounting a Signaling Server
- Rack-mounting a Terminal Server
- Rack-mounting a BayStack 470 Switch
- Rack-mounting a BayStack 460 Power over Ethernet unit
- Installing system grounds
- Contents
- Introduction
- Installing a ground bar
- Grounding a CS 1000E Call Server
- Grounding a Signaling Server
- Grounding a Media Gateway powered by the same electrical panel
- Grounding a Media Gateway powered by multiple electrical panels
- Grounding a Media Gateway Expander
- Grounding other rack-mounted components
- Grounding equipment in the UK
- Connecting CS 1000E system components
- Contents
- Introduction
- Connecting Call Server 0 to Call Server 1
- Connecting the CS 1000E Core Call Servers to an MG 1000E
- Connecting a Signaling Server to the ELAN subnet
- Connecting a Signaling Server to the TLAN subnet
- Inserting a Shielded 50-pin to Serial/ELAN/TLAN adapter onto a Media Card
- Connecting a Media Card to the ELAN subnet
- Connecting a Media Card to the TLAN subnet
- Connecting a Media Gateway to a Media Gateway Expansion
- Installing software on the CS 1000E
- Connecting MG 1000T system components
- Contents
- Introduction
- Connecting an MG 1000T Core to a Survivable MG 1000T Expansion
- Connecting an MG 1000T Core to the ELAN subnet
- Connecting a Signaling Server to the ELAN subnet
- Connecting a Signaling Server to the TLAN subnet
- Inserting a Shielded 50-pin to Serial/ELAN/TLAN adapter onto a Media Card
- Connecting a Media Card to the ELAN
- Connecting a Media Card to the TLAN subnet
- Connecting a Media Gateway to a Media Gateway Expansion
- Installing and configuring the Signaling Server software
- Configuring the CS 1000E Call Server
- Contents
- Introduction
- Enabling the Login Name option
- Configuring login IDs and passwords
- Enabling the multi-user option
- Configuring pseudo-terminals (PTYs)
- Checking PTY status
- Configuring Virtual Tone and Conference Circuits
- Configuring the MG 1000E Bandwidth Management Zones
- Configuring the MG 1000E ports
- Configuring Digitone Receivers
- Configuring Tone Detectors
- Logging in to Element Manager
- Importing preconfigured IP telephony files
- Reviewing and submitting IP telephony node configuration files
- Adding a Follower Signaling Server to an IP telephony node
- Performing a datadump
- Configuring a Small System Controller
- Installing software on an MG 1000E Small System Controller
- Installing software on an MG 1000T Small System Controller
- Connecting a Terminal Server
- Configuring a terminal and SDI ports
- Verifying the network
- Installing and cross-connecting a trunk card
- Installing and configuring a Voice Gateway Media Card
- Contents
- Introduction
- Configuring a card
- Adding a card to an IP telephony node
- Configuring a card as a node Leader
- Configuring voice gateway channels using Element Manager
- Configuring voice gateway channels using LD 14
- Saving configuration changes
- Installing a CompactFlash
- Installing a card in a Media Gateway
- Verifying a card
- Disabling a card
- Disabling a card unit
- Enabling a card
- Enabling a card unit
- Verifying functionality
- Upgrading loadware
- Installing the Main Distribution Frame
- Configuring an IP telephony node
- Installing Line cards and cross-connecting telephones
- Installing and configuring IP Phones
- Contents
- Introduction
- Package components for the IP Phones
- Configuring VoIP bandwidth management zones
- Configuring virtual superloops
- Configuring an IP Phone using LD 11
- Setting administrator and temporary IP Telephone Installer passwords
- Installing IP Phone hardware components
- Configuring the IP Phone boot parameters
- Entering IP Phone boot parameters using manual configuration
- Entering IP Phone boot parameters using full DHCP parameters
- Entering IP Phone boot parameters using partial DHCP parameters
- Using Set-Based Installation
- Installing the IP Softphone 2050
- Verifying IP Phone functionality
- Displaying registered IP Phones
- Upgrading firmware
- Installing and cross-connecting a Power Fail Transfer Unit
- Installing and cross-connecting an external alarm from a PFTU
- Configuring MG 1000T survivability and alternate primary controller
- Contents
- Introduction
- MG 1000T switch over to Survival Mode
- Switchback from Survival Mode
- LOCK and UNLOCK commands
- Database synchronization
- Configuring a survivable MG 1000T Expansion
- Printing Survivable MG 1000T Expansion parameters
- Configuring Alternate primary controller
- Verifying IP telephony node operation in Survival Mode
- Retrieving CDR records from a survivable MG 1000T Expansion
- Basic system telephony configuration
- Configuring IP Peer Networking and managing the Gatekeeper database