Norton 7100SZ Series Safe Zone With External Sensor Installation And Instruction Manual 80 9371 0084 020

User Manual: Norton 7100SZ Series SafeZone with External Sensor Installation and Instruction Manual Installation

Open the PDF directly: View PDF .
Page Count: 6

1

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9371-0084-020 (01-14)

• Allen wrench set (inch)

• Flat blade screwdriver (potentiometer & terminal size)

• Screwdriver (Phillips size 2)

• Tape rule

• Power drill

• Center punch

• Wire stripper

Tools required:

Mechanical Installation 2

Wiring Diagrams 3

Sensor Settings 4

Sensing Field Settings 5

Trouble Shooting 5

Specifications 6

Safety Precautions 6

Table of Contents:

ASSA ABLOY

Patent Pending

®

7100SZ Series SafeZone

External Sensor

Installation and Instruction Manual

3.14

(79.8)

4.76

(120)

2.0

(50.8)

2

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9371-0084-020 (01-14)

MOUNTING TEMPLATE

DRILL

1/8” HOLE

DRILL

1/8” HOLE

DRILL 1/4” HOLE

THEN INSERT CABLE

PLACE TEMPLATE

AT LEASE 1” ABOVE

BOTTOM OF HEADER

For optional cable routing, notch

cover in one of the areas shown.

10'-0" Max height

Above floor surface

2.0"

Frame Face

1.0" Min.

Above Frame Face

Note:

If frame face is 3.0" or greater,

Sensor can be mounted on frame

face.

1. Apply adhesive backed template, supplied with

sensor, to appropriate surface and aligned with

centerline of door on side of opening opposite

from SafeZone Mount.

2. Drill two 1/8" holes for mounting.

3. Drill one 1/4" hole for cable access.

4. Insert mounting screws into mount surface, but

do not screw them fully in.

5. Route wiring through backplate.

6. Mount sensor backplate and tighten screws.

7. Complete wiring connections and sensor setup

and testing.

8. Secure sensor cover to backplate.

C

LOf Door

Electrical Cable

See page 3 for Wiring Diagrams

See page 4 for Sensor Adjustments

MOUNTING TEMPLATE

DRILL

1/8” HOLE

DRILL

1/8” HOLE

DRILL 1/4” HOLE

THEN INSERT CABLE

PLACE TEMPLATE

AT LEASE 1” ABOVE

BOTTOM OF HEADER

Opening the sensor

Mechanical Installation

*

*

*

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9371-0084-020 (01-14)

3

Wiring Diagram

(Wiring external sensor to SafeZone Unit)

24VDC

Terminal Connection

1 (Red) 24 VDC (+)

2 (Black) 24 VDC (-)

3 (White) Relay Common

4 (Green) Relay N.O.

5 Relay N.C.

Note: Input power tolerance is +/- 10% for

AC, and -10% to +30% for DC power.

12345

12345

SafeZone Unit 24VDC

Closer

Solenoid

Red

Black Green

Jumper Wire

External Sensor

24VDC (-)

24VDC (+)

Wiring Diagram

(Wiring external sensor to SafeZone Unit)

120VAC

SafeZone Unit 120VAC

Red

Black Green

Jumper Wire

External Sensor

Closer

Solenoid

L

N

G

12345

12345

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9371-0084-020 (01-14)

4

Terminal Block

Planner Antenna

(Narrow)

Hold Time Buttons

Lateral and Angular

Antenna Adjustments

Wire

Passage

Increase (+)

Decrease (-) LED

Wire Knockout

(Inside Cover) Cover removal slot

Front Cover

s

Default Factory Settings:

Sensitivity 3

Hold Time 10 seconds

Immunity 2

Detection Mode 1 (Bidirectional)

Door Control Mode 1

Setting Time (Seconds)

1 5

2 6

3 7

4 8

5 (Default) 10

6 14

7 16

8 18

9 20

0 0.5

Recommended Hold Time Settings

Setting 4-6

Setting 1-3 Setting 7-9

Setting Hold Open Time:

Press and release the Increase

(+) or decrease (-) buttons until

desired setting is achieved.

Reset Hold Time to Default:

Holding both buttons depressed

simultaneously for 3 seconds

will set unit at default hold time

of 10 seconds.

Hold Time

Hold open time is defined as the amount of time the door will remain open

AFTER movement in opening is no longer detected.

Sensitivity Setting

Sensitivity is factory set at setting #3. The sensitivity range is (0 - 9). This setting

can be adjusted along with other advanced settings when using the optional

remote.

Optional remote for advanced setting.

List number 7100REM

Sensor Settings

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9371-0084-020 (01-14)

5

Troubleshooting

SYMPTOMS PROBABLE CORRECTIVE

CAUSE ACTION

Door Stops several times in

the same cycle without

sensing presence in the door

way.

Sensitivity is set too high Change sensitivity setting using

optional remote.

Door not closing when cover

installed.

Eye is sensing the closer

cover.

Adjust the sensing field away from

cover edge. (See “Sensing Field

Adjustments” above.

Power switch is off.

Loose wire connection.

Turn power switch to “ON” position.

Inspect wiring for loose connections.

Red LED does not light up.

(No power to sensor)

16" 0

0

16"

16"

32"

48"

32" 32"

Nominal Detection Pattern with Sensor Set as follows:

Mounting Height: 7'-2"

Sensitivity: 3 (factory default)

Immunity: 2 (factory default)

Direction Mode: 1 (Bi-Directional; factory default)

Door Control: 1 (factory default)

Vertical Tilt: 30°

Lateral Tilt: 0°

Altering the lateral tilt angle will shift the detection

pattern left or right of center.

Note:

Always “walk” the opening during senor adjustment to

confirm the detection pattern is adequate for the

opening and application.

Adjusted hole open times as required for application.

See page 4 for hold open time settings.

Sensing Field Adjustments

0º 30º 45º

The position of the sensing field is determined by the vertical and lateral angle of the antenna.

Sensing field as close to the door as possible:

Antenna is set at the position of 0°

Sensing field far from the door:

Antenna is set at the position of 45°

Sensing field close to the door:

Antenna is set at the position of 30°

Vertical Angle Adjustments Lateral Angle Adjustments

+15°-15°

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9371-0084-020 (01-14)

6

Sensor Technical Specifications

DESCRIPTION SPECIFICATION

Frequency: 24.125 GHz

Suppl voltage: y 24 VDC: -10% / +30%:

Mounting height: Normal: 7’; Maximum: 10’-0”

Tilt angle: 0 to 90 vertical

-15 to +15 lateral

Detection area:

Wide

Narrow

13ft (W) x 6.5ft (D)

6.5ft (W) x 8.2ft (D) (supplied as optional)

Minimum detection speed: 2 in/sec. (measured in axis)

Power consumption: < 2 W

Standard output relay:

Max contact voltage

Max contact current

Max s itching po ew w r

60 VDC / 125 VAC

1 A (resistive)

30W (DC / 60V) A (AC)

Hold time: 0.5 sec. to 9 sec. (adjustable)

Temperature range: -4°F to 131°F

Dimensions: 4.75in (W) x 3.15in (H) x 2.0in (D)

Weight: 0.5lbs

Material: ABS

®

SafeZone

Safety Precautions

• Shut off all power going to the header before attempting any wiring procedures.

• Maintain a clean & safe environment when working in public areas.

• Constantly be aware of pedestrian traffic around the door area.

• Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by

the door.

• Always check placement of all wiring and components before po ering upw to ensure that moving door parts will not

catch an w res and cause damay i ge to equipment.

• Ensure compliance w yith all applicable safet standards upon completion of installation.

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

Circuit board components are vulnerable to damage by electrostatic discharge

(ESD). ESD can cause immediate or subtle damage to sensitive electronic parts.

An electrostatic charge can build up on the human body and then discharge when

you touch a board. A discharge can be produced when walking across a carpet

and touching a board, for example. Before handling any board, make sure you

dissipate your body’s charge.

CAUTION: In the event a unit needs to be opened, observe the following precautions.

Ground yourself by touching a conductive surface of the door or other element connected to common earth

ground to discharge the static electricity present in your body.



Avoid walking around while replacing items inside the case, especially if you are on carpet or during

conditions of low temperature and low humidity.



Handle the board by the edges only to avoid touching electronic components.

Store a loose board in an anti-static bag.

•

•

•

•

3000 Highway 74 East • Monroe, NC 28112

Tel: (877)- • Fax: (800)-338-0965974-2255

www. no r to ndoorcontrols. com

ASSA ABLOY