Norton 7290MPI, 7290 MPS Overhead Concealed Closer/Holder 80 9372 1071 020

User Manual: Norton 7290MPI, 7290 MPS Overhead Concealed Closer/Holder Installation

Open the PDF directly: View PDF .
Page Count: 6

Download
Open PDF In Browser	View PDF

Support Unit Models

7290 MPI (Infinite Hold Open Range)
ASSA ABLOY
Range)
7290 MPS (Selective Hold-Open

ASSA ABLOY
Multi-Point Electromechanical
Overhead Concealed Closer
Holder Releasing Device
with Rigid Slide Arm
For wood or metal doors 1- 3/4” to 2 -1/4" (45-57mm) thick
Hung in a hollow metal frame
Standard butt hinges

80-9372-1071-020 (01-14)

CAUTION
An incorrectly installed or improperly
adjusted door closer can cause property
damage or personal injury. These instructions
should be followed to avoid the possibility
of misapplication or misadjustment.

Typical Installation
• One track & closer position for all door opening angles
• Easy arm attachment
• Removable Frame Stop Required*-Not Shown

Hinge or
Pivot

Right Hand Door-RH
Left Hand Reverse-LHR

Left Hand Door-LH
Right Hand Reverse-RHR

Hinge or
Pivot

*Not required when frame rabbet exceeds 2-3/16" (56mm).
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

80-9372-1071-020 (01-14)

Model 7290MPI/7290MPS
Multi-Point Electromechanical
Overhead Concealed
With Rigid Slide Arm

Templa-te Standard Butt Hinges
ASSA ABLOY

Viewed From Above

4 Holes
for Closer Fasteners

3/8
(9.5)

2
(50.8)

1-1/4
(31.8)
22-1/4
(565.2)

3/8
(9.5)
2
(50.8)

7/8
Dia. Hole
(22.2) (Conduit)

23
(584.2)

C
L Conduit

20-1/4 Ref.
(514.4)

1"
(25.4)

CL Closer
Dust Box
(By frame mfr.)

Conduit Box

5/32 to Centerline
(4.0)
Of Conduit Hole

Reinforcement
(By frame mfr.)
CL

1/8 Ref.
(3.2)
Removable
Frame Stop
(By frame mfr.)

21
(533.4)
Frame Reinforcements

Min. 1-3/4
(44.5)

C
L Hinge
Viewed From Above
11/16
(to edge of cutout)
(17.5)

4 Holes
for Track
Fasteners

1-1/4
(31.8)

Max. 2-1/4
(57.2)

1"
(25.4)
1"
(25.4)

14
(355.6)

2-1/2
(63.5)
1/8
(3.2)

3/8
(9.5)

Hinge
1/4
(6.4)
C
L Door and Track

C
L Door
and
Track
8
(203.2)

1-3/16
(30.2)

3-3/4
(95.3)

LEFT
HAND DOOR

5/8
(15.9)
22
(558.8)

24
3/8 (9.5) deep cutout in shaded area
(609.6)
24
(609.6)

Fastener

NOTES:
• Do not scale drawing.
• Left hand door shown.
• Hardware dimensions shown (not
cutouts).
• Dimensions are in inches (mm).
• Minimum door width 27" (685.8).
• Track 24" (609.6) long.
• Maximum width hinge is 5" (127).

1/4-20 machine
screw
#14 wood screw

Preparation

Use

metal frame
#7 (.201" dia.) or 5.10mm. drill
and
1/4-20 tap
metal door
wood
door

7/32" or 5.5mm. drill

Track Installation
Door Angle
180°
110°

Auxiliary Door
Stop Required

With
Without
Cushion and Cushion and
stop block
Stop block

Opening
greater
than 110º

See installation sequence on pages 4 & 5.

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

Page 2

80-9372-1071-020 (01-14)

Model 7290MPI/7290MPS
Multi-Point Electromechanical
Overhead Concealed
With Rigid Slide Arm

Components
ASSA ABLOY
Plug
(MPS Unit only)
Closer Assembly

Conduit Box Cover

Cam
Plug
(MPS & MPI Unit)

H

in

ge

Conduit Knockout

L

(5)
Dress Plate
Mounting Screws
6-32 x 3/8 long

S
S/D

Spring
Tube

Conduit Box

P
B

Short
Dress Plate

Self Clinching Studs

Positioning
Screw

Mounting Plate

Cushion and
Stop Block
Arm

Track

Flat Washer
with
countersink

(4)
Mounting screws
1-4-20 x 5/8 long

(2)
Arm/track screw
1/4-20 x 3/4” long
Hex drive with
thread lock

(4)
Track screws
1/4-20 x 7/16”
or
14-10 x 1-1/4” long
wood screws

Long Dress Plate

Arm

Slider

This end of slider (short
side) toward cushion
and stop block.

Align Squares

Stud
Slider

Screw Pack

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

Page 3

80-9372-1071-020 (01-14)

Installation Sequence
Note: Read instructions entirely prior to installation.

ASSA ABLOY

Door/Frame Prep:
• Determine hand of door from illustration on page 1.
Closer are handed. Hand of closer must match hand of
door.
• Using template dimensions on page 2, locate holes
and cutouts in frame and door, unless a separate
template has been supplied for your application.

12

Door:
Prepare door for track. Drill and tap (4) holes for 1/4-20
machine screws.

3

Frame:
Prepare the frame for mounting closer. Drill and tap (4)
holes for 1/4-20 machine screws or #14 wood screws.
Note: Generally on new construction hardware
cutouts are made by suppliers at their shop.

Wiring:
• Wiring of switch must be in compliance with N.E.C.
Class 2 wiring specifications.
• Voltage to unit must be the same as shown on the unit:
24 Volts AC/DC or 120 Volts AC, 60hz. Voltage must be
within a range of plus 10% and minus 15% of the unit's
stated voltage.

Terminal Block
FUSE
0.75 AMPS
(+)

• Pull hook-up box off mounting plate's self clinching
studs, disconnect plugs and remove hook-up box
cover.

(-)

VI

(+)
(-)

TEST
SWITCH

3
2
1

ALARM PANEL

DOOR HOLDER
CIRCUIT

• Anchor conduit at 1 or 2 hook-up box knockouts.
• Secure power input leads to terminal lock, positions #1
and #2 as shown.
SPECIFICATIONS
120VAC
Voltage

MAX.
120V 132V
102V MIN.

Current

.035 AMPS

24VDC

24VAC
24V

26.4V MAX.
20.4V MIN.

26.4V MAX.

24V 20.4V MIN.

.070 AMPS .070 AMPS

FUSE

VoltageTest
Socket
Pos. (+) Black

OPTIONAL SELECTIVE
HOLD OPEN
SWITCH

SOLENOID
COIL

Reconnect sockets
a. Connect plug with white leads from solenoid for
MPI and MPS units.
b. Connect plug with black leads from cam switch
if used.
Replace hook-up box cover and secure with (2) screws.

Test switch
(Push)

VoltageTest
Socket
Neu. (-) white

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

Reattached hook-up box to mounting plate by aligning
(2) holes at bottom of hook-up box with (2) self clinching
studs. See illustration on page 3.

Page 4

80-9372-1071-020 (01-14)

Installation Sequence con't
ASSA ABLOY
• Determine door opening angle
See page 2 and below.
• Series 7290MPI: Infinite Hold Open units
will hold door at virtually any degree of
door opening from 5° to 175°.
• Series 7290MPS: Selective Open Hold
units are shipped with hold open set at
approximately 85°. Hold open can be set
from 5° to 175°.
The hold open position can be increased
or decreased by loosening the cam screw,
rotating the cam to the new setting and
tighten cam screw. See chart below for cam
settings where hold open range will start.

• Mount closer to frame.
Position spring tube away from hinge and
mounting plate flush with frame rabbet.
Secure to frame reinforcements with (4)
1/4 -20 x 5/8 screws. Use care to avoid damaging
or pinching wires.
• Install arm on closer pinion (see illustration below)
Position arm counterbore facing down with
index mark aligned with pinion index mark. Install
onto pinion. Secure with washer and flat head arm
screw with thread lock (see page 3).

Left hand

Arm in position

• Align letters on hold open cam with
“V” centerline of switch rocker. Choose
row of letters on cam that are closest to
the hinge side face of door.

Setting

G

H

J

K

Door Angle 15º 30º 45º 60º

L

Right hand

(Bottom View)

Pinion Mark
Arm Index Mark

M

90º 135º

NOTE: Verify setting of cam before
mounting closer to the frame.

• Install track in door.
Place the assembled track into door cutout with
open side up, cushion and stop block if used, toward
the hinge. Move slider to the opposite
end of track (see illustration, page 3). Secure track
with (4) 1/4-20 machine screws.
• Connect arm to track. Open door to approximately
5" (127mm), rotate arm to slider and place end on
stud. Use a screw driver to align the square on slider’s
stud with the arm square (see illustration on page 3).
Push down on arm to seat stud and to prevent stud
from rotating. Secure with arm/track screw,
1/4-20 x 5/8” long flat head hex drive with thread
lock.

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

Page 5

80-9372-1071-020 (01-14)

Model 7290MPI/7290MPS
Multi-Point Electromechanical
Overhead Concealed
With Rigid Slide Arm

Closer Adjustment
CAUTION: ASSA ABLOY
Do not back valves out of
closer or a leak will result.

Standard
Door Closer

Door Closing Controls
"L"

Range

Door Opening Controls
"BC"

"S"

Closing Power Adjustment

Range

Range

Never Close Completely

INCREASE

MODEL
7290

SIZE HAND
RH
4

BC
LATCH

BC

POWER ADJUST

POSITION

SWEEP

DECREASE

Mounting Base Plate

Closing Controls

Latch

Opening Controls

Sweep

Delayed Action

• Closer Controls accessible through mounting plate for closer adjustment:
Use 1/8" (3mm.) hex-key for valve adjustments.
Use standard screwdriver for power adjustment.
• Power Adjustment permits increasing door closing force.
Controlled by slotted screw marked "P.A."

Backcheck

VoltageTest
Socket
Pos. (+) Black

FUSE

• Closing Speed controlled by valves marked "SWEEP" and "LATCH".
Attention: Adjust closing speed time to between 4 to 7 seconds from 90°.
Use of the door by handicapped, elderly, or small children may require
greater closing time.
• Backcheck cushions or slows the opening of a door that is forced
to travel faster than conditions require.
Backcheck controlled by valves marked "BC POSITION" (open for
backcheck start at a greater door opening angle) and "BC" (for
adjusting backcheck intensity). Never close "BC" valve completely.
• Optional Enhanced Backcheck provides adjustable backcheck intensity
beginning at approximately 15° of the door opening cycle. Backcheck
positioning valve is omitted when this feature is provided.

Test switch
(Push)

VoltageTest
Socket
Neu. (-) white

• Hold Open Check. Turn power to the unit “On”. Open door to the hold open
position. Manually pull door out of hold open and release, door should close.
• Hook-Up Box Testing. Open door to the hold open position. Depress “Test
Switch” button on Hook-up Board, accessible through cutout in hook-up
box and mounting plate (see illustration at right). Door should close.

3000 Highway 74 East • Monroe, NC 28112
Tel: (877)- 974-2255 • Fax: (800)-338-0965
www.nor tondoorcontrols.com

• Install short and long dress plates with (5) 6-32 screws.
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

Page 6

80-9372-1071-020 (01-14)



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 6
Create Date                     : 2014:01:13 12:06:21-05:00
Modify Date                     : 2014:01:13 12:06:21-05:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Author                          : McNally;Tommy
Creator                         : CorelDRAW X6
Title                           : Untitled-1

EXIF Metadata provided by EXIF.tools