Norton 7290MPI, 7290 MPS Overhead Concealed Closer/Holder 80 9372 1071 020

User Manual: Norton 7290MPI, 7290 MPS Overhead Concealed Closer/Holder Installation

Open the PDF directly: View PDF .
Page Count: 6

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9372-1071-020 (01-14)

ASSA ABLOY

Multi-Point Electromechanical

Overhead Concealed Closer

Holder Releasing Device

with Rigid Slide Arm

80-9372-1071-020 (01-14)

7290 MPI

7290 MPS

(Infinite Hold Open Range)

(Selective Hold-Open Range)

Support Unit Models

For wood or metal doors 1- 3/4” to 2 -1/4" (45-57mm) thick

Standard butt hinges

Hung in a hollow metal frame

Typical Installation

• Removable Frame Stop Required*-Not Shown

• One track & closer position for all door opening angles

• Easy arm attachment

An incorrectly installed or improperly

adjusted door closer can cause property

damage or personal injury. These instructions

should be followed to avoid the possibility

of misapplication or misadjustment.

CAUTION

*Not required when frame rabbet exceeds 2-3/16" (56mm).

Hinge or

Pivot

Right Hand Door-RH

Left Hand Reverse-LHR

Hinge or

Pivot Left Hand Door-LH

Right Hand Reverse-RHR

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9372-1071-020 (01-14)

Page 2

See installation sequence on pages 4 & 5.

Hinge

Door

and

Track

14

(355.6) 22

(558.8)

3/8 (9.5) deep cutout in shaded area

8

(203.2)

1"

(25.4)

4 Holes

for Track

Fasteners

Viewed From Above

11/16

(17.5)

24

(609.6)

20-1/4

1/8 Ref.

Conduit Box

Reinforcement

(By frame mfr.)

1"

(25.4)

21

(533.4)

Frame Reinforcements

C

L

Ref.

C

L

Conduit

22-1/4

(565.2)

23

(584.2)

Viewed From Above

3/8

(9.5)

1-1/4

(31.8)

2

(50.8)

4 Holes

for Closer Fasteners

C

L

Track Installation

Door Angle Auxiliary Door

Stop Required

110° 180°

With

Cushion and

stop block

Without

Cushion and

Stop block

Opening

greater

than 110º

Templa-te Standard Butt Hinges

2-1/4

(57.2)

Min.

Removable

Frame Stop

(By frame mfr.) 3/8

(9.5)

1-3/16

(30.2)

3-3/4

(95.3)

LEFT

HAND DOOR

Dust Box

(By frame mfr.)

Closer

5/32

(4.0)

Dia. Hole

(Conduit)

2-1/2

(63.5)

1/8

(3.2)

C

L

Multi-Point Electromechanical

Overhead Concealed

Model 7290MPI/7290MPS

With Rigid Slide Arm

NOTES:

• Do not scale drawing.

• Left hand door shown.

• Hardware dimensions shown (not

cutouts).

• Dimensions are in inches (mm).

• Minimum door width 27" (685.8).

• Track 24" (609.6) long.

• Maximum width hinge is 5" (127).

3/8

(9.5)

2

(50.8)

(514.4)

(3.2)

1-3/4

(44.5)

(to edge of cutout)

1"

(25.4)

24

(609.6)

1-1/4

(31.8)

5/8

(15.9)

Fastener Use Preparation

1/4-20 machine

screw

#14 wood screw

metal frame

and

metal door

wood

door

#7 (.201" dia.) or . drill

1/4-20 tap

5.10mm

7/32" or drill5.5mm.

7/8

(22.2)

to Centerline

Of Conduit Hole

C

L

Max.

C

LDoor and Track

1/4

(6.4)

Hinge

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9372-1071-020 (01-14)

Page 3

S

L

S/D

P

B

Conduit Knockout

Dress Plate

Mounting Screws

6-32 x 3/8 long

(5)

(4)

Mounting screws

1-4-20 x 5/8 long

Conduit Box

Plug

(MPS Unit only)

Cam

Plug

(MPS & MPI Unit)

Short

Dress Plate

Track screws

1/4-20 x 7/16”

or

14-10 x 1-1/4” long

wood screws

Positioning

Screw

Cushion and

Stop Block

(4)

Track

(2)

Arm/track screw

1/4-20 x 3/4” long

Hex drive with

thread lock

Slider

Arm

Flat Washer

with

countersink

Screw Pack

Align Squares

Stud

Arm

Slider

This end of slider (short

side) toward cushion

and stop block.

Components

Multi-Point Electromechanical

Overhead Concealed

Model 7290MPI/7290MPS

With Rigid Slide Arm

Conduit Box Cover

Closer Assembly

Spring

Tube

Hinge

Self Clinching Studs

Mounting Plate

Long Dress Plate

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9372-1071-020 (01-14)

Page 4

Note: Generally on new construction hardware

cutouts are made by suppliers at their shop.

Reconnect sockets

. Connect plug with black leads from cam switch

if used.

Reattached hook-up box to mounting plate by aligning

(2) holes at bottom of hook-up box with (2) self clinching

studs. See illustration on page 3.

a. Connect plug with white leads from solenoid for

MPI and MPS units.

b

Replace hook-up box cover and secure with (2) screws.

Installation Sequence

3

2

1DOOR HOLDER

CIRCUIT

ALARM PANEL

FUSE

0.75 AMPS (+)

(-)

VI

(-)

(+)

SOLENOID

COIL

OPTIONAL SELECTIVE

HOLD OPEN

SWITCH

TEST

SWITCH

SPECIFICATIONS

Voltage

Current

120VAC 24VAC 24VDC

120V 24V 24V

.070 AMPS

.070 AMPS

.035 AMPS

132V MAX.

102V MIN.

26.4V MAX.

20.4V MIN.

26.4V MAX.

20.4V MIN.

FUSE VoltageTest

Socket

Pos. (+) Black

VoltageTest

Socket

Neu. (-) white

Test switch

(Push)

123

Terminal Block

Door/Frame Prep:

Note: Read instructions entirely prior to installation.

Wiring:

• Wiring of switch must be in compliance with N.E.C.

Class 2 wiring specifications.

• Voltage to unit must be the same as shown on the unit:

24 Volts AC/DC or 120 Volts AC, 60hz. Voltage must be

within a range of plus 10% and minus 15% of the unit's

stated voltage.

• Pull hook-up box off mounting plate's self clinching

studs, disconnect plugs and remove hook-up box

cover.

• Anchor conduit at 1 or 2 hook-up box knockouts.

• Secure power input leads to terminal lock, positions #1

and #2 as shown.

• Determine hand of door from illustration on page 1.

Closer are handed. Hand of closer must match hand of

door.

• Using template dimensions on page 2, locate holes

and cutouts in frame and door, unless a separate

template has been supplied for your application.

Door:

Prepare door for track. Drill and tap (4) holes for 1/4-20

machine screws.

Frame:

Prepare the frame for mounting closer. Drill and tap (4)

holes for 1/4-20 machine screws or #14 wood screws.

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9372-1071-020 (01-14)

Page 5

Setting

Door Angle

G H J K L M

135º

15º 30º 45º 60º 90º

• Determine door opening angle

the hinge side face of door.

See page 2 and below.

units

will hold door at virtually any degree of

door opening from

Selective Open Hold

units are shipped with hold open set at

The hold open position can be increased

or decreased by loosening the cam screw,

rotating the cam to the new setting and

tighten cam screw. See chart below for cam

settings where hold open range will start.

• Align letters on hold open cam with

“V” centerline of switch rocker. Choose

row of letters on cam that are closest to

• Series 7290MPI: Infinite Hold Open

• Series 7290MPS:

5° to 175°.

• Mount closer to frame.

Position spring tube away from hinge and

mounting plate flush with frame rabbet.

Secure to frame reinforcements with (4)

1/4 -20 x 5/8 screws. Use care to avoid damaging

or pinching wires.

• Install arm on closer pinion (see illustration below)

Position arm counterbore facing down with

index mark aligned with pinion index mark. Install

onto pinion. Secure with washer and flat head arm

screw with thread lock (see page 3).

Arm in position

(Bottom View)

Pinion Mark

Right hand

Left hand

Arm Index Mark

• Install track in door.

Place the assembled track into door cutout with

open side up, cushion and block if used, toward

the hinge. Move slider to the opposite

end of track (see illustration, page 3). Secure track

with (4) 1/4-20 machine screws.

stop

• Connect arm to track. Open door to approximately

5" (127mm), rotate arm to slider and place end on

stud. Use a screw driver to align the square on slider’s

stud with the arm square (see illustration on page 3).

Push down on arm to seat stud and to prevent stud

from rotating. Secure with arm/track screw,

1/4-20 x 5/8” long flat head hex drive with thread

lock.

NOTE: Verify setting of cam before

mounting closer to the frame.

Installation Sequence con't

approximately 85°. Hold open can be set

from 5° to 175°.

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Copyright © 2002, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9372-1071-020 (01-14)

Page 6

3000 Highway 74 East • Monroe, NC 28112

Tel: (877)- • Fax: (800)-338-0965974-2255

ww w.no r to nd oo rc on tr ols.c om

ASSA ABLOY

accessible through mounting plate for closer adjustment:

Use 1/8" (3mm.) hex-key for valve adjustments.

Use standard screwdriver for power adjustment.

• Closer Controls

permits increasing door closing force.

Controlled by slotted screw marked "P.A."

• Power Adjustment

controlled by valves marked "SWEEP" and "LATCH".

Attention: Adjust closing speed time to between 4 to 7 seconds from 90°.

Use of the door by handicapped, elderly, or small children may require

greater closing time.

• Closing Speed

cushions or slows the opening of a door that is forced

to travel faster than conditions require.

Backcheck controlled by valves marked "BC POSITION" (open for

backcheck start at a greater door opening angle) and "BC" (for

adjusting backcheck intensity). Never close "BC" valve completely.

• Backcheck

Delayed Action Backcheck

Sweep

Latch

Closing Controls Opening Controls

CAUTION:

Do not back valves out of

closer or a leak will result.

Closer Adjustment

Standard

Door Closer Closing Power Adjustment

Door Closing Controls Door Opening Controls

Never Close Completely

"BC"

Range

"L"

Range "S"

Range

provides adjustable backcheck intensity

beginning at approximately 15° of the door opening cycle. Backcheck

positioning valve is omitted when this feature is provided.

• Optional Enhanced Backcheck

BC BC

POSITION

MODEL SIZE

4

HAND

RH

7290 LATCH SWEEP POWER ADJUST

INCREASE

DECREASE

Mounting Base Plate

• Hook-Up Box Testing.

Turn power to the unit “On”. Open door to the hold open

position. Manually pull door out of hold open and release, door should close.

Open door to the hold open position. Depress “Test

Switch” button on Hook-up Board, accessible through cutout in hook-up

box and mounting plate (see illustration at right). Door should close.

• Install short and long dress plates with (5) 6-32 screws.

FUSE

VoltageTest

Socket

Pos. (+) Black

VoltageTest

Socket

Neu. (-) white

Test switch

(Push)

Multi-Point Electromechanical

Overhead Concealed

Model 7290MPI/7290MPS

With Rigid Slide Arm

• Hold Open Check.