Norton Master (PTDO) Or Support (PTO) Units, Push Pull Side 80 9377 0716 020

User Manual: Norton Master (PTDO) or Support (PTO) Units, Push or Pull Side Installation

Open the PDF directly: View PDF PDF.
Page Count: 4

DownloadNorton  Master (PTDO) Or Support (PTO) Units, Push Pull Side 80-9377-0716-020
Open PDF In BrowserView PDF
Power Track® Series
Master Unit – PTDO (with detector)
Support Unit - PTO (without detector)
ASSA ABLOY

CAUTION
An incorrectly installed or improperly
adjusted door closer can cause property
damage or personal injury. These instructions
should be followed to avoid the possibility
of misapplication or misadjustment.

Models

Hinge (Pull) Side of Stop (Push) Side of
Door Application
Door Application

ASSA ABLOY

7705PTDO
7705PTO

Installation Instructions
Combination Door Closer-Holder and
Releasing Device WITH and WITHOUT
Integral Smoke Detector

7705PTDO
PULL SIDE
illustrated
LH – Left Hand Door
RHR – Right Hand Reverse

NOTES: - For wiring of PTDO models, see "PowerTrack®"
"Wiring Instructions" No. 80-9342-0902-021 (01-09)
- When used with a PTDO model, PTO unit must
be a 24V unit

P7705PTDO
PUSH SIDE
illustrated
LH – Left Hand Door
RHR – Right Hand Reverse

PTO UNITS NOT SHOWN

Preparation for Fasteners

Components:
9/64"
Hex Drive
Socket Screw

PTOHB24
PTOHB120

Arm Assembly
7700ST-1A

2 Cover Screws

PTO Track
PTO24
PTO120

Pull (Hinge) Side
Push (Stop) Side

7700M *

7700P

PPTDO Hook-Up Box
PPTDOHB24
PPTDOHB120

PPTO24
PPTO120

PPTOHB24
PPTOHB120

L S

L

S
P

D
P

Delayed
Action Option

PPTO Track
PPTO Hook-Up Box

Metal Cover
with Clips

Plastic Cover
(Standard)

PTDO Hook-Up Box
PTDOHB24
PTDOHB120

Door or Frame Drill-Sizes
Aluminum
or Metal No drill required
Self-Drilling Screw
Standard
Wood 3/16” (4.30 mm)
Pilot hole required
1/4” - 20 machine
Metal Drill: #7 (0.201” dia.)
Tap: 1/4” - 20
screw
Hollow 9/32” (7 mm) through;
Metal 3/8” (9.5 mm) door face
opposite to closer
Sleeve nuts and
Aluminum 3/8” (9.5 mm) through
bolts
Optional
or Wood
9/32” (7 mm);
Through-bolts and
All
3/8” (9.5 mm) dia. x
grommet-nuts
3/8” (9.5 mm) deep on
door opposite to closer
Fasteners

PTO Hook-Up Box

Smoke
Detector

P7705PTDO
P7705PTO

BC

BC

Standard
7705LAP

7705LAP-DA
Smoke
Detector

Power Adjustment Nut
* This cover is only available for PULL SIDE applications.

 For special applications a separate door and frame

 Use of an auxiliary door stop is always recommended.
 Unit must be mounted on interior of building in dry

 Use this instruction sheet for installation sequence and

 See NFPA70 for wiring requirements and NFPA72 for alarm

NOTE:
preparation template is packed with these instructions.

closer adjustments only.

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

environment, maximum humidity of 95%.

system requirements.

1

80-9377-0716-020 (04-14)

7705PTO/7705PTDO Series
Hinge (Pull) Side Application
Parts

ASSA ABLOY

1

2

Mark and Drill Holes
CL

1/2
(13)

B
A
3-5/8
(92)

Solenoid wire
coiled inside
end of track

3/4
(19)
5
6-3/4
(171)
(127)
Right Hand Shown
Co
ve
r
Optional

Installation Sequence

3

RH Door

After installed,
bend out tabs
to secure.

Dim. "B”

PTO

31-1/16
(788)

32-1/8
(816)

34-11/16
(881)

35-3/4
(908)

+

Sweep

C

Preparation for Fasteners

Dim. "A”

LH Door

Closer
Valves
Up

7/8 (22) Conduit
hole for concealed
wiring only

2-3/8
(60)

Power Track

PTDO

Closer
Valves
Down

-

1-1/4
(32)

1-7/16
(37)

19
(483)

4

Door or
Frame
Aluminum
or Metal
Wood
(see Note)

Fasteners

Self-Drilling
Screw
1/4”-20
machine screw

Metal

Drill Sizes
No drill required
3-16” (4.3mm)
Drill #7 (.201” dia)
Tap 1/4”-20

Note: Wood doors/frames MUST have pilot
hole when using Self-Drilling Screws.

Latch

-

+

5

Pinion Flat

F

G

See Page 4 for
wiring instructions.
B

A

I

Position

Backcheck

+

D
H

2

Hold Open Angle

7

(Between 85° and 110° only)
A
B

-

Caution:
Don't completely
close cushion valve

1

Lock into
hold-open

6

Cushion

+

!

E

-

D
Use holes
that align
in arms

8

Closing Force

Install closer per instructions with the
proper pre-load applied to the arm
then adjust spring power. The
power adjustment will not work
properly if the closer spring is
not pre-loaded.
Product shipped
with closing force
set at the middle of
the power range.

+

Optional Cover

9

7700M

_

7700P

C Open door to
desired angle

DO NOT use a power drill or driver
to turn adjustment nut. This will
damage closer and void warranty.

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

2

80-9377-0716-020 (04-14)

P7705PTO/P7705PTDO Series
Stop (Push) Side Application

ASSA ABLOY

1

Parts

Mark and Drill Holes
CL

3-1/8
(79)

2

B

A
12
(305)

Solenoid wire
coiled inside
end of track

4
(102)

4
(102)

4-3/4
(121)

Bottom of Frame Stop

4
5/16 1-1/8
(102) (8) (29)

2-5/8
(67)

Used for 7788
Drop Plate

2-3/8
(60) 4-1/4
(108)

Co
ve
r
Optional

Left Hand Shown
6-3/4
(171)

Preparation for Fasteners
Door or
Frame
Aluminum
or Metal
Wood
(see Note)

Fasteners

Installation Sequence

3

Pinion Flat

Closer
Valves
Down

See Page 4 for
wiring instructions.
B

Power Track

Dim. "A”

Dim. "B”

PTO

30-9/16
(776)

31-11/16
(805)

34-3/16
(868)

35-5/16
(897)

PTDO

LH Door RH Door

+

Sweep

Closer
Valves
Up

4

-

Self-Drilling
Screw
1/4”-20
machine screw

No drill required
3-16” (4.3mm)
Drill #7 (.201” dia)
Tap 1/4”-20

Note: Wood doors/frames MUST have pilot
hole when using Self-Drilling Screws.

Latch

-

+

5

F

Position

Backcheck

C

+

A
D

2
G

(Between 85° and 110° only)
A
Lock into
B

6

Cushion

+

!

-

Caution:
Don't completely
close cushion valve

Closing Force

Hold Open Angle

hold-open

Metal

Drill Sizes

E

H

1

1/2
(13)

1-1/8 (29) hole
for Conduit
1
(25)

19
(486)

D
Use holes
that align
in arms

+
C Open door to
desired angle

8

Optional Cover

Install closer per instructions with the
proper pre-load applied to the arm then
adjust spring power. The power
adjustment will not work properly if 7700M
the closer spring is not pre-loaded.
Product shipped with
closing force set at the
middle of the power
range.

_

DO NOT use a power drill or driver
to turn adjustment nut. This will
damage closer and void warranty.

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

9

7700P

3

80-9377-0716-020 (04-14)

PTO Support Unit Wiring Diagram
(120VAC Input)

PTO Support Unit Wiring Diagram
(24VAC/DC Input)

Input
Power
Earth
(+)
(-)

24VAC/DC Circuit Board

Input
Power

4-Pin
Jumper

3
2
1

Earth
(+)
(-)

1
2
3
4

2-Pin Jumper

Openings for surface
wiring shown

120VAC Circuit Board

1
2
3
4

2-Pin Jumper

Openings for surface
or concealed wiring

Header for Solenoid
Connection

SOL

Fuse (PTO125V)
125V / 1/2A

Terminal Strip for
Power Input Connection

Test Switch

4-Pin
Jumper

3
2
1

SOL

Fuse (PTO125V)
125V / 1/2A

Terminal Strip for
Power Input Connection

(Do not use a 120VAC PTO unit when power is
supplied from a PTDO unit)ASSA ABLOY

Header for Solenoid
Connection

Test Switch

ELECTRICAL DATA
120VAC

For PTDO Models:
Refer to Wiring Instructions
No. 80-9342-0902-021 (01-09)
for making wiring connections.

24VAC

24VDC

Detector

132V Max
26.4V Max
26.4V Max
26.4V Max
Voltage 120V 102V Min 24V 20.4V Min 24V 20.4V Min 24V 20.4V Min
Current

.036 Amps

.059 Amps

.074 Amps

0.034 Amps

NOTES:
 Maximum wire size is 14AWG.
 All wiring and connections use standard wiring practice conforming with
local wiring codes.

 Again, open door to the hold-open position.
Depress “Test Switch” button on the hook-up
board (accessible through cover)...door should
close. If arm does not release, see previous step.

IMPORTANT:
Remove solenoid wire from end of track before
installing track to frame. Do not pinch or crimp wire.
Once track and hook-up box are installed, solenoid
wire must be plugged into Header on circuit board
shown above.

Installation of Cover:
 Plastic Cover (7700P): Slide cover insert into the
un-used cutout in cover. Install cover using
screws provided.
 Metal Cover (7700M): Fasten cover to mounting
clips with screws provided.

After making all wiring connections:
 Turn power to unit “ON”. (On Master (PTDO) unit
only, red LED should illuminate once every 15
sec.).
 Track’s hold open force is preset at the factory.
 Open door to hold-open position. Manually pull
door out of hold-open and release...door should
close. If arm does not release from hold-open,
increase the releasing force by turning the screw
accessible thru the end cap of the track using the
9/64” hex wrench provided.
Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY
3000 Highway 74 East • Monroe, NC 28112
Tel: (877)- 974-2255 • Fax: (800)-338-0965
www.nor tondoorcontrols.com

4

80-9377-0716-020 (04-14)



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 4
Create Date                     : 2014:04:15 16:35:27-04:00
Modify Date                     : 2014:04:15 16:35:27-04:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Author                          : McNally;Tommy
Creator                         : CorelDRAW X6
Title                           : Untitled-1
EXIF Metadata provided by EXIF.tools

Navigation menu