Norton Master (PTDO) Or Support (PTO) Units, Push Pull Side 80 9377 0716 020

User Manual: Norton Master (PTDO) or Support (PTO) Units, Push or Pull Side Installation

Open the PDF directly: View PDF .
Page Count: 4

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9377-0716-020 (04-14)

1

Installation Instructions

Combination Door Closer-Holder and

Releasing Device WITH and WITHOUT

Integral Smoke Detector

An incorrectly installed or improperly

adjusted door closer can cause property

damage or personal injury. These instructions

should be followed to avoid the possibility

of misapplication or misadjustment.

CAUTION ®

Power Track Series

Master Unit – PTDO (with detector)

Support Unit - PTO (without detector)

Models

Hinge (Pull) Side of

Door Application

Stop (Push) Side of

Door Application

7705PTDO

7705PTO

P7705PTDO

P7705PTO

7705PTDO

PULL SIDE

illustrated

LH – Left Hand Door

RHR – Right Hand Reverse

P7705PTDO

PUSH SIDE

illustrated

LH – Left Hand Door

RHR – Right Hand Reverse

Components:

®

NOTES: - For wiring of PTDO models, see "PowerTrack "

"Wiring Instructions" No. 80-9342-0902-021 (01-09)

- When used with a PTDO model, PTO unit must

be a 24V unit

* This cover is only available for PULL SIDE applications.

ASSA ABLOY

PTO UNITS NOT SHOWN

Arm Assembly

7700ST-1A

9/64"

Hex Drive

Socket Screw

Metal Cover

with Clips

7700M *

Power Adjustment Nut

Delayed

Action Option

7705LAP-DA

Standard

7705LAP

BC

P

D

S

L

BC

P

S

L

Plastic Cover

(Standard)

7700P

2 Cover Screws

Push (Stop) Side

Pull (Hinge) Side

PTO Hook-Up Box

PTOHB24

PTOHB120

PTO Track

PTO24

PTO120

PPTO Track

PPTO24

PPTO120

PPTO Hook-Up Box

PPTOHB24

PPTOHB120

PPTDO Hook-Up Box

PPTDOHB24

PPTDOHB120

Smoke

Detector

PTDO Hook-Up Box

PTDOHB24

PTDOHB120

Smoke

Detector

9/32” (7 mm);

3/8” (9.5 mm) dia. x

3/8” (9.5 mm) deep on

door opposite to closer

Standard

Optional

Through-bolts and

grommet-nuts

All

Preparation for Fasteners

Door or Frame

Fasteners Drill-Sizes

Self-Drilling Screw

Wood 3/16” (4.30 mm)

Pilot hole required

1/4” - 20 machine

screw Metal Drill: #7 (0.201” dia.)

Tap: 1/4” - 20

Sleeve nuts and

bolts

Hollow

Metal

9/32” (7 mm) through;

3/8” (9.5 mm) door face

opposite to closer

Aluminum

or Wood

3/8” (9.5 mm) through

Aluminum

or Metal No drill required

NOTE:

For special applications a separate door and frame

preparation template is packed with these instructions.

Use this instruction sheet for installation sequence and

closer adjustments only.

Use of an auxiliary door stop is always recommended.

Unit must be mounted on interior of building in dry

environment, maximum humidity of 95%.

See NFPA70 for wiring requirements and NFPA72 for alarm

system requirements.

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9377-0716-020 (04-14)

2

9

8

7

6

5

3

12

4

Cover

Optional

Latch

Sweep

Parts

Caution:

Don't completely

close cushion valve

Optional Cover

Hinge (Pull) Side Application

Right Hand Shown

Mark and Drill Holes

Installation Sequence

!

19

(483)

3-5/8

(92)

A

B

5

(127)

6-3/4

(171)

C

L

Closing Force

7700M

7700P

A

C

After installed,

bend out tabs

to secure.

D

G

See Page 4 for

wiring instructions.

2

1

H

Pinion Flat

RH Door LH Door

F

Power Track

PTO

PTDO

31-1/16

(788)

34-11/16

(881)

Dim. "A”

32-1/8

(816)

35-3/4

(908)

Dim. "B”

Hold Open Angle

(Between 85° and 110° only)

A

Lock into

hold-open

C Open door to

desired angle

BD

Use holes

that align

in arms

I

7/8 (22) Conduit

hole for concealed

wiring only

1/2

(13)

B

7705PTO/7705PTDO Series

Closer

Valves

Up

Closer

Valves

Down

E

-

+

-

+

Backcheck

-

+

-

+

Cushion

Position

Self-Drilling

Screw Wood

(see Note)

No drill required

3-16” (4.3mm)

Drill #7 (.201” dia)

Tap 1/4”-20

Metal

Fasteners Door or

Frame Drill Sizes

Preparation for Fasteners

Note: Wood doors/frames MUST have pilot

hole when using Self-Drilling Screws.

1/4”-20

machine screw

Aluminum

or Metal

3/4

(19)

1-7/16

(37)

1-1/4

(32)

2-3/8

(60)

Solenoid wire

coiled inside

end of track

+_

Product shipped

with closing force

set at the middle of

the power range.

DO NOT use a power drill or driver

to turn adjustment nut. This will

damage closer and void warranty.

Install closer per instructions with the

proper pre-load applied to the arm

then adjust spring power. The

power adjustment will not work

properly if the closer spring is

not pre-loaded.

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9377-0716-020 (04-14)

3

Optional

3

Parts

Stop (Push) Side Application

2

Left Hand Shown

Mark and Drill Holes

Installation Sequence

12

(305)

3-1/8

(79)

AB

C

L

A

F

D

G

Power Track

PTO

PTDO

30-9/16

(776)

34-3/16

(868)

Dim. "A”

31-11/16

(805)

35-5/16

(897)

Dim. "B”

H

19

(486)

Used for 7788

Drop Plate

1

(25)

1-1/8 (29) hole

for Conduit

Bottom of Frame Stop

4

(102)

4-3/4

(121)

1-1/8

(29)

5/16

(8)

2-5/8

(67)

2-3/8

(60)

1/2

(13)

See Page 4 for

wiring instructions.

B

5

C

P7705PTO/P7705PTDO Series

9

6

4Latch

Sweep

Caution:

Don't completely

close cushion valve

Optional Cover

!

Closing Force 8

7700M

7700P

-

+

-

+

Backcheck

-

+

-

+

Cushion

Position

Hold Open Angle

(Between 85° and 110° only)

A

Lock into

hold-open

C Open door to

desired angle

BD

Use holes

that align

in arms

E

Self-Drilling

Screw Wood

(see Note)

No drill required

3-16” (4.3mm)

Drill #7 (.201” dia)

Tap 1/4”-20

Metal

Fasteners Door or

Frame Drill Sizes

Preparation for Fasteners

Note: Wood doors/frames MUST have pilot

hole when using Self-Drilling Screws.

1/4”-20

machine screw

Aluminum

or Metal

Cover

4-1/4

(108)

6-3/4

(171)

4

(102)

4

(102)

1

2

1

Pinion Flat

RH DoorLH Door

Closer

Valves

Down

Closer

Valves

Up

Solenoid wire

coiled inside

end of track

+_

Product shipped with

closing force set at the

middle of the power

range.

DO NOT use a power drill or driver

to turn adjustment nut. This will

damage closer and void warranty.

Install closer per instructions with the

proper pre-load applied to the arm then

adjust spring power. The power

adjustment will not work properly if

the closer spring is not pre-loaded.

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9377-0716-020 (04-14)

4

PTO Support Unit Wiring Diagram

(24VAC/DC Input)

PTO Support Unit Wiring Diagram

(120VAC Input)

(Do not use a 120VAC PTO unit when power is

supplied from a PTDO unit)

2-Pin Jumper SOL

1

2

3

4

3

2

1

24VAC/DC Circuit Board 4-Pin

Jumper

2-Pin Jumper SOL

1

2

3

4

3

2

1

120VAC Circuit Board 4-Pin

Jumper

Test Switch

Header for Solenoid

Connection

Openings for surface

wiring shown Fuse (PTO125V)

125V / 1/2A

Terminal Strip for

Power Input Connection Test Switch

Openings for surface

or concealed wiring

Terminal Strip for

Power Input Connection

ELECTRICAL DATA

NOTES:

Maximum wire size is 14AWG.

All wiring and connections use standard wiring practice conforming with

local wiring codes.

For PTDO Models:

Refer to Wiring Instructions

No. 80-9342-0902-021 (01-09)

for making wiring connections.

Earth

(+)

(-)

Earth

(+)

(-)

Input

Power

Input

Power

Again, open door to the hold-open position.

Depress “Test Switch” button on the hook-up

board (accessible through cover)...door should

close. If arm does not release, see previous step.

Installation of Cover:

Plastic Cover (7700P): Slide cover insert into the

un-used cutout in cover. Install cover using

screws provided.

Metal Cover (7700M): Fasten cover to mounting

clips with screws provided.

IMPORTANT:

Remove solenoid wire from end of track before

installing track to frame. Do not pinch or crimp wire.

Once track and hook-up box are installed, solenoid

wire must be plugged into Header on circuit board

shown above.

After making all wiring connections:

Turn power to unit “ON”. (On Master (PTDO) unit

only, red LED should illuminate once every 15

sec.).

Track’s hold open force is preset at the factory.

Open door to hold-open position. Manually pull

door out of hold-open and release...door should

close. If arm does not release from hold-open,

increase the releasing force by turning the screw

accessible thru the end cap of the track using the

9/64” hex wrench provided.

120VAC 24VAC 24VDC

Voltage

Current

120V 24V 24V

132V Max

102V Min

26.4V Max

20.4V Min

26.4V Max

20.4V Min

.036 Amps .059 Amps .074 Amps

Detector

26.4V Max

20.4V Min

0.034 Amps

24V

Header for Solenoid

Connection

Fuse (PTO125V)

125V / 1/2A

3000 Highway 74 East • Monroe, NC 28112

Tel: (877)- • Fax: (800)-338-0965974-2255

www. no r to nd oo rc ont rol s. co m

ASSA ABLOY