Nutek ATNF Transmitter User Manual

Nutek Corporation Transmitter Users Manual

Users Manual

1PROPLME Install Guide rev A.PROPLME Installation InstructionsFCC COMPLIANCEThis device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including any interference that may cause undesired operation.Warning! Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Technical Support (800) 225-6074or go tohttp://avxtech1.comInstallation Precautions:Roll down window to avoid locking keys in vehicle during installationAvoid mounting components or routing wires near hot surfacesAvoid mounting components or routing wires near moving partsTape or loom wires under hood for protection and appearanceUse a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR “COMPUTER SAFE PROBE” as these can set off air bags or damage vehicle computers.Use grommets when routing wires through metal surfaces
22014 VOXX Electronics Corporation. All rights reserved.Security System Layout .............................................................................. 4I.T.S. Interior Theft Sensor Layout .............................................................5Setup & Programming - Consumer Mode ................................................. 6 Consumer Mode Types ............................................................................. 6 Consumer Mode Transmitter Programming .............................................. 6 Consumer Mode Feature Programming Bank - Without Transmitters ......6 Consumer Mode Feature Programming Bank - With Transmitters ...........7 Defaulting All Options in the Feature Programming Bank ......................... 7 Consumer Mode Feature Programming Banks ......................................... 8 Setup & Programming - LOT Mode ............................................................ 9 Dealer Lot Mode Description .................................................................... 9 Lot Mode ACM Keypad Transmitter Programming .................................... 9 Lot Mode Feature Programming - Without an ACM Keypad ..................... 9 Lot Mode Feature Programming - With an ACM Keypad ........................ 10 Defaulting the Feature in the Feature Programming Bank ...................... 10 Lot Mode Feature Programming Banks .................................................. 11Consumer & Lot Mode Types ................................................................... 12 Consumer Mode Types ........................................................................... 12 Lot Mode Types ....................................................................................... 12Transitioning Between Modes - ACM Keypad ........................................13 Entering into Lot Mode from any Consumer Mode ..................................13 Blue Mode - Keyless Entry Security Upgrade .........................................13 Red Mode - Remote Vehicle Security & Keyless Entry ........................... 14 Green Mode - I.T.S. Interior Theft Sensor ............................................... 14 Yellow Mode - No-Sale ............................................................................ 15 Purple Mode - BCA Borrowed Car Agreement ........................................15 Table of Contents
3PROPLME Install Guide rev A. Purple Mode - BCA Borrowed Car Agreement ........................................15Transitioning Between Modes - Short Range Transmitter ..................... 16 Entering into Lot Mode from any Consumer Mode ..................................16 Transitioning into Consumer Mode ..........................................................16On Board Shock Sensor ........................................................................... 17Wire Connection Guide .............................................................................18 8 Pin Main Harness .................................................................................19 6 Pin Input / Output Harness ...................................................................21 5 Pin Input Harness ................................................................................. 22 3 Pin Door Lock Harness ........................................................................24Accessory Connectors ............................................................................. 35I.T.S. Interior Theft Sensor Functionality .................................................36I.T.S. Activation ..........................................................................................36 Factory Alarm Trigger .............................................................................. 36 Optional Warn Away ................................................................................ 36 Valet Mode ............................................................................................... 37 I.T.S. Harness Connections ..................................................................... 37System Power-up Procedure.................................................................... 38Mounting the Module/Finishing the Installation ..................................... 38Feature Descriptions ................................................................................. 39Additional Features ................................................................................... 42 Arm System with Shock Sensor Bypassed ............................................. 42 Attempted Intrusion Identication ............................................................42 Valet Mode ............................................................................................... 42 Deleting Arm / Disarm Notication Chirps ............................................... 42 Dome Light Delay / Theater Lighting Programming ................................ 43Aftermarket Transmitter Functions..........................................................43
42014 VOXX Electronics Corporation. All rights reserved.SECURITY SYSTEM LAYOUTORANGE 86 - ARMED OUTPUT ( - ) RED 85 - IGNITION ( + ) BLACK 87A - STARTER OUTPUT - MOTOR SIDEWHITE / BLACK 30 - STARTER OUTPUT - KEY SIDESTARTER INTERUPT RELAYRELAY &HARNESS#1363731BLACK GROUNDYELLOW IGNITIONPURPLE DOOR TRIGGER (+)RED PARKING LIGHT INPUTWHITE PARKING LIGHT OUTPUTBROWN DOOR TRIGGER (-)RED/WHITE +12 VOLT BATTERYORANGE ARMED OUTPUT (-) OPENDK GREEN INSTANT TRIGGER (-)BLACK/WHITE HORN OUTPUT (-)LT. GREEN INSTANT TRIGGER (-)GREEN/WHITE ILLUMINATED ENTRY (-)DK BLUE TRUNK RELEASE (-) BLUE TRUNK SHUNT (+)RED/BLACK DISARM INPUT 2RED/YELLOW DISARM INPUTGREEN/BLACK ARM INPUT 2GREEN ARM INPUTRED/BLACK 2ND UNLOCKGREEN UNLOCK OUPUT (-)RED LOCK OUTPUT (-)TELEMATIC PORTDBI PORT3 Pin 5 Pin 6 Pin 8 PinLED / OVERRIDE PODSHOCK SENSOR DIALPROGRAMMING BUTTON#4120016#4120019#4120018#4120017 #4120015LOT MODE / CONSUMER SECURITY MODE
5PROPLME Install Guide rev A.I.T.S. - INTERIOR THEFT SENSOR LAYOUTBLACK GROUNDYELLOW IGNITIONPURPLE DOOR TRIGGER (+)RED N/AWHITE N/ABROWN DOOR TRIGGER (-)RED/WHITE +12 VOLT BATTERYORANGE N/A OPENDK GREEN N/ABLACK/WHITE HORN OUTPUT (-)LT. GREEN N/AGREEN/WHITE N/ADK BLUE FACTORY ALARM TRIGGER (-) BLUE N/ARED/BLACK N/ARED/YELLOW N/AGREEN/BLACK N/AGREEN N/ARED/BLACK N/AGREEN N/ARED N/ATELEMATIC PORTDBI PORT3 Pin 5 Pin 6 Pin 8 PinLED / OVERRIDE PODSHOCK SENSOR DIALPROGRAMMING BUTTON#4120016#4120019#4120018#4120017 #4120015I.T.S. - INTERIOR THERFT SENSOR - MODEPlease note that this layout is simplied for a basic ITS mode installation with the minimum required connections. If needed, other connections such as the 5 pin arm/disarm harness may still be utilized to arm or disarm the system using the vehicle’s factory remote transmit-ters.
62014 VOXX Electronics Corporation. All rights reserved.SETUP & PROGRAMMING - CONSUMER MODESConsumer Mode Transmitter Programming1. Open a door.2. Turn the ignition ON. 3. Press and release the override button 3 times.4. The system will chirp 1 time.5. Press the lock button of each transmitter you wish to program. 6. The system will respond with 1 chirp for each accepted transmitter.7. Turn the ignition OFF to exit transmitter programming.8. The system will chirp 2 times to conrm exit.Note: This system has 1 button programming which programs all channels of the transmitter to the system at once. Consumer Mode Feature Programming - Without Transmitters1. Open a door.2. Turn the ignition ON.3. Press and release the override button 3 times, the system will chirp 1 time.4. Turn the ignition OFF, the system will chirp 2 times.5. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The LED will ash the current setting for the option.6. Use the override button to scroll through the selections in the feature bank, the system will chirp to match the feature number.7. Press the programming button on the module to change the desired feature, The LED will ash indicating the feature’s setting.8. Turn the ignition OFF to exit programming, the system will chirp 1 time to conrm exit.Consumer Mode TypesBlue Mode - Keyless Entry Security Upgrade System. Full security utilizing the vehicle’s existing factory remote transmitters.Red Mode - Remote Vehicle Security & Keyless Entry System. Full security adding aftermarket remote transmitters.Green Mode - Interior Theft Sensor. Add-on impact sensor for vehicles with basic factory security systems and can also be controlled by either the factory or aftermarket remote transmitters.
7PROPLME Install Guide rev A. Defaulting All Options in the Feature Programming Bank1. Open a door.2. Turn the ignition ON. 3. Press and release the override button 3 times, the system will chirp 1 times4. Press the programming button on the module, the system will chirp 4 times indicating the features have been defaulted.5. Continue on to edit option settings or turn off the ignition to exit programming.NOTE: This will also default the Dome Light Delay timing if a custom time was set. Consumer Mode Feature Programming - With Transmitters1. Open a door. 2. Turn the ignition ON.3. Press and release the override button 3 times, the system will chirp 1 time.4. Turn the ignition OFF, the system will chirp 2 times.5. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The LED will ash the current setting for the option.6. Use the CAR FIND/PANIC button to scroll through the selections in the feature bank, the system will chirp to match the feature number.7. Press the LOCK button to change the desired feature. The LED will ash indicating the feature’s setting.8. Turn the ignition OFF to exit programming, the system will chirp 1 time to conrm exit.
82014 VOXX Electronics Corporation. All rights reserved.Programming Notes: • The system will remain in programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.• Changing feature #11 to either of the “ITS Functionality” settings will change the functionality of the entire system, refer to the “I.T.S. - Interior Theft Sensor Functionality” section of this manual for details.• Default setting are listed in BOLD. Consumer Mode - Feature Programming BanksFeature Bank 1Transm itter ProgrammingFeature Bank 2Consumer Mode Security Control 1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 1Security Function ON OFFON - Warn Away Disabled 2Passive Locks PassiveActive3Silent Choice ON OFF4Passive/Active Arming PassiveActive5Siren/Horn SirenHorn6Door Trigger DelayInstant15 Second7Arm 2 Input PolarityNegative ( - )Posi tive ( + )8ChirpsON OFFON - Including ITS Mode9Door Lock Output Timing0.9 Seconds 3 Seconds0.9 Sec / Dbl Pulse Unlock 0.75 Seconds10 Ignition Controlled Door Locks ALLLock Only Unlock OnlyOFF11 DK BLUE Wire Output Trunk ITS FunctionITS Function - Warn Away Disabled12 Disarm 2 Input PolarityNegative ( - )Posi tive ( + )13 Horn Output Timing10mS 16mS 40mS 72mS14 Real Panic Sound ON OFF15 ORANGE Wire Output ( - ) Armed Output( - ) Disarmed Output16 Arming DelayOFF45 Seconds Factory R/S Option17 GREEN /WHITE Wire Output Illuminated EntryFactory Disarm
9PROPLME Install Guide rev A.SETUP & PROGRAMMING - LOT MODE Lot Mode ACM Keypad Transmitter Programming1. Open a door.2. Turn the ignition ON. 3. Press and release the override button 3 times, the system will chirp 1 time.4. Enter the desired VEHICLE NUMBER into the ACM keypad and then press the LOCK button, the system will respond with 1 chirp.5. Turn the ignition OFF to exit transmitter programming, the system will chirp 2 times to conrm exit.NOTE: This system has 1 button programming which programs all channels of the transmitter to the system at once.When an ACM keypad is programmed to the system, it is automatically transi-tioned into Lot Mode. Only 1 vehicle number may be learned to the system. Lot Mode Feature Programming - Without an ACM Keypad1. Open a door.2. Turn the ignition ON.3. Press and release the override button 3 times, the system will chirp 1 time.4. Turn the ignition OFF, the system will chirp 2 times.5. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The LED will ash the current setting for the option.6. Use the override button to scroll through the selections in the feature bank, the system will chirp to match the feature number.7. Press the programming button on the module to change the desired feature. The LED will ash indicating the feature’s setting.8. Turn the ignition OFF to exit programming, the system will chirp 1 time to conrm exit.Dealer Lot Mode DescriptionLot Mode - Dealer Lot Protection & Keyless Entry System. Limited security features. Passive arming / locking and starter interrupt utilizing a dealer ACM Keypad remote transmitter.
10 2014 VOXX Electronics Corporation. All rights reserved. Lot Mode Feature Programming - With an ACM Keypad1. Open a door.2. Turn the ignition ON.3. Press and release the override button 3 times, the system will chirp 1 time.4. Turn the ignition OFF, the system will chirp 2 times.5. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The LED will ash the current setting for the option.6. Use the CAR FIND/PANIC button to scroll through the selections in the feature bank, the system will chirp to match the feature number.7. Press the LOCK button to change the desired feature. The LED will ash indicating the feature’s setting.8. Turn the ignition OFF to exit programming, the system will chirp 1 time to conrm exit. Defaulting All Options in the Feature Programming Bank1. Open a door.2. Turn the ignition ON.3. Press and release the override button 3 times, the system will chirp 1 time.4. Press the programming button on the module, the system will chirp 4 times indicating the features have been defaulted.5. Continue on to edit option settings or turn off the ignition to exit programming.NOTE: This will also default the Dome Light Delay timing if a custom time was set.
11PROPLME Install Guide rev A.Programming Notes: • The system will remain in programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.• Changing feature #11 to either of the “ITS Functionality” settings will change the functionality of the entire system, refer to the “I.T.S. - Interior Theft Sensor Functionality” section of this manual for details.• Default setting are listed in BOLD. Lot Mode - Feature Programming BanksFeature Bank 2Lot Mode Security Control 1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 1Security Function ON OFFON - Warn Away Disabled 2Passive Locks Passi ve Active3Silent ChoiceONOFF4Passive/Active Arming Passi ve Active5Siren/Horn SirenHorn6Door Trigger DelayInstant15 Second7Arm 2 Input PolarityNegative ( - )Posi tive ( + )8ChirpsONOFFON - Including ITS Mode9Door Lock Output Timing0.9 Seconds 3 Seconds 0.9 Sec / Dbl Pulse Unlock 0.75 Seconds10 Ignition Controlled Door Locks ALLLock Only Unlock OnlyOFF11 DK BLUE Wire Output Trunk ITS FunctionITS Function - Warn Away Disabled12 Disarm 2 Input PolarityNegative ( - )Posi tive ( + )13 Horn Output Timing10mS16mS 40mS72mS14 Real Panic Sound ON OFF15 ORANGE Wire Output ( - ) Armed Output( - ) Disarmed Output16 Arming Delay OFF45 Seconds Factory R/S Option17 GREEN /WHITE Wire Output Illuminated EntryFactory Disarm 18 Lot Alert OFFON19 Lot Mode Passive Arming Ti mersTX Disarm / Ignition 5 / 30 minute1 / 1 minuteFeature Bank 1Transm itter Programming
12 2014 VOXX Electronics Corporation. All rights reserved.Consumer Mode TypesBlue Mode - Keyless Entry Security Upgrade System. Full security utilizing the vehicle’s existing factory remote transmitters. The LED will ash BLUE in this mode.Red Mode - Remote Vehicle Security & Keyless Entry System. Full security adding aftermarket remote transmitters. The LED will ash RED in this mode.Green Mode - Interior Theft Sensor. Add-on impact sensor for vehicles with basic factory security systems and can also be controlled by either the factory or aftermarket remote transmitters. The LED will ash GREEN in this mode.Lot Mode TypesYellow Mode - No-Sale Mode. Completely disables the system. Requires a special xture to recover from this mode. The LED does not ash. Lot Mode - Dealer Lot Protection & Keyless Entry System. Limited security features. Passive arming / locking and starter interrupt utilizing a dealer ACM Keypad remote transmitter. The LED will ash RED in this mode.BCA Mode - Borrowed Car Agreement. BCA Mode can also only be accessed while in Lot Mode and puts the Lot Mode feature into a “valet” status to allow an extended driving period for the customer. BCA Mode is only accessible through special access ACM Keypads. The LED alternates between RED and BLUE in this mode.The system is shipped from the factory in BLUE mode, programming a Remote transmitter to the system will cause the unit to enter RED mode. The only difference between the blue and red modes are the addition of the transmitters in red mode. The GREEN mode can be activated while in the consumer Blue/Red modes by changing the option in the programming bank. Transitioning into Lot Mode or from Lot Mode into any of the consumer modes requires an authorized ACM keypad and is explained in the sections that follow.CONSUMER & LOT MODE TYPES
13PROPLME Install Guide rev A.Entering into Lot Mode from any Consumer Mode1. Turn the ignition ON. 2. Press and release the override button 3 times, the system will chirp 1 time.3. Enter the desired VEHICLE NUMBER into the ACM keypad and then press the LOCK button. 4. The system will respond with 1 chirp.5. Turn the ignition OFF to exit transmitter programming, the system will chirp 2 times to conrm exit.Notes:• This system has 1 button programming which programs all channels of the transmitter to the system at once.• Use of an ACM keypad is required.• Once an ACM keypad is programmed to the system, it is automatically transitioned into Lot Mode. Only 1 vehicle number may be learned to the system.• When in lot mode, a consumer remote can not be programmed to the system until it is transitioned to consumer mode.• All programming features will be defaulted to the factory default settings.TRANSITIONING BETWEEN MODES - ACM KEYPADBlue Mode - Keyless Entry Security Upgrade1. Open a vehicle door.2. Enter the vehicle number into an ACM keypad.3. Press the UNLOCK button.4. Press and release the TRANS button.5. Press and release the “BLUE” button. 6. The LED will ash blue 1 time and the system will chirp 3 times.7. Close the vehicle’s door.Notes:• The ACM keypad must be authorized for transitioning.• Factory Keyless Upgrade Mode enables all of the device’s security functionality and utilizes the factory remote transmitters.
14 2014 VOXX Electronics Corporation. All rights reserved.Green Mode - I.T.S. Interior Theft Sensor1. Open a vehicle door.2. Enter the vehicle number into an ACM keypad.3. Press the UNLOCK button.4. Press and release the TRANS button.5. Press and release the “GREEN” button.6. Close the vehicle’s door.Notes:• The ACM keypad must be authorized for transitioning.• I.T.S. mode enables the shock sensor only of this device for applications in a vehicle equipped with a factory security system. Red Mode - Remote Vehicle Security & Keyless Entry1. Open a vehicle door.2. Enter the vehicle number into an ACM keypad.3. Press the UNLOCK button.4. Press and release the TRANS button.5. Press and release the “RED” button.6. The LED will ash red 1 time and the system will chirp 3 times.7. Within 5 seconds program the aftermarket transmitter by pressing the lock but ton of each transmitter you wish to program. 8. Close the vehicle’s door.Notes: • The ACM keypad must be authorized for transitioning.• If no remotes are programmed during step 7, the system will automatically transition into the Factory Keyless Entry Security Upgrade Mode - BLUE• Security with Transmitters Mode enables all of the device’s security functionality by use of aftermarket transmitters.
15PROPLME Install Guide rev A.Yellow Mode - No-Sale1. Open a vehicle door.2. Enter the vehicle number into an ACM keypad.3. Press the UNLOCK button.4. Press and release the TRANS button.5. Press and release the “YELLOW” button.6. Close the vehicle’s door.Notes:• The ACM keypad must be authorized for transitioning.• No-Sale mode disables all functionality of the unit and requires a programming jig to recover the module from this mode. This mode is typically only used when there is a no-sale of the product and you are not removing the system from the vehicle.Purple Mode - B.C.A. Borrowed Car Agreement1. Open a vehicle door.2. Enter the vehicle number into an ACM keypad.3. Press the UNLOCK button.4. Press and release the TRANS button.5. Press and release the “PURPLE” button.6. Close the vehicle’s door.Notes: • The ACM keypad must be authorized for BCA transitioning.• Lot Mode and puts the Lot Mode feature into a “valet” status to allow an extended driving period for the customer. Note that the is still in Lot Mode.Exit B.C.A. ModeExiting B.C.A. Mode returns the unit to an active Lot Mode state with the original vehicle stock number entered when Lot Mode was activated.1. Open a vehicle door.2. Turn ON the vehicle’s ignition.3. Press and Hold the valet button for 3 seconds. The unit will exit BCA Mode.
16 2014 VOXX Electronics Corporation. All rights reserved.Transitioning into Consumer Mode1. Open a vehicle door.2. Press and hold button 2 of the short range transmitter until the system chirps 3 times.3. Again press and hold button 2 of the short range transmitter until the system chirps 3 times.4. Within 5 seconds program a consumer remote. If no remotes are programmed in the 5 second window, the system will default to the factory keyless upgrade setting which uses the factory remote controls to arm and disarm the system. Notes:• Programming features 1-4 will be defaulted to the factory default settings, programming features 5-13 will retain any changes that have been made.Entering into Lot Mode from any Consumer Mode1. Turn the ignition ON. 2. Press and release the override button 3 times, the system will chirp 1 time.3. Press button 1 of the short range transmitter, the system will chirp 1 time.4. Turn the ignition OFF to exit transmitter programming.5. The system will chirp 2 times to conrm exit.Notes:• This system has 1 button programming which programs all channels of the transmitter to the system at once.• When in lot mode, a consumer remote can not be programmed to the system until it is transitioned to consumer mode.• All programming features will be defaulted to the factory default settings.TRANSITIONING BETWEEN MODES - SHORT RANGE TRANSMITTER
17PROPLME Install Guide rev A.ON BOARD SHOCK SENSORAdjusting and Testing the Shock SensorIt is recommended that you test the shock sensor after making any adjustments to the sensitivity.The shock sensor has two levels of protection, one to detect light impacts to the vehicle and one to detect larger impacts. Adjusting the shock sensor’s sensitivity dial will adjust both light and full triggers zones simultaneously. If the light impact zone, also referred to as warn-away, can be turned completely off in option programming. To test the shock sensor, arm the system and wait 6 - 10 seconds for the zone to stabi-lize, then rmly strike the vehicle being careful not to damage it. Repeat if necessary. • Increase sensitivity by turning the adjustment dial clockwise.• Decrease sensitivity by turning the adjustment dial counter clockwise. When using the aftermarket remote transmitter the shock sensor can be temporarily bypassed when for one arm cycle by pressing Trunk or Find button within 5 seconds of pressing the Lock button.
18 2014 VOXX Electronics Corporation. All rights reserved.1BLACKGROUND2YELLOWIGNITION ( + )3PURPLE DOOR TRIGGER INPUT ( + )4REDPARKING LIGHT INPUT5WHITEPARKING LIGHT OUTPUT6BROWNDOOR TRIGGER INPUT ( - )7RED / WHITEBATTERY 12V ( + )8ORANGE ARMED OUTPUT ( - )8 PIN MAIN1BLUE TRUNK SHUNT INPUT ( + )2RED / BLACKDISARM INPUT 2 3RED/YELLOW DISARM INPUT4GREEN / BLACK ARM INPUT 25GREEN ARM INPUT5 PIN INPUT1OPEN2DK GREEN INSTANT TRIGGER INPUT ( - )3BLACK / WHITEHORN OUTPUT ( - )4LT GREEN INSTANT TRIGGER INPUT ( - )5GREEN / WHITEILLUMINATE D ENTRY OUTPUT ( - )6DK BLUETRUNK RELEASE OUTPUT ( - )6 PIN INPUT / OUTPUT8 PIN MAIN HARNESS6 PIN INPUT / OUTPUT HARNESS5 PIN INPUT HARNESS
19PROPLME Install Guide rev A.8 PIN MAIN HARNESS 1 BLACK Chassis Ground Source ( - ) Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver’s side kick panel area.NOTE: Do not ground the BLACK wire with any other vehicle components.1RED / BLACK2ND UNLOCK OUTPUT ( - )2GREEN UNLOCK OUTPUT ( - )3REDLOCK OUTPUT ( - )3 PINLOCK86 ORANGE ARMED OUTPUT ( - )85 REDIGNITION ( + )87aBLACKSTA RTER OUTPUT - MOTOR SIDE87 WHITE / BLACK STARTER OUTPUT - KEY SIDESTARTER INTERUPT RELAY3 PIN LOCK HARNESSSTARTER INTERRUPT HARNESS 2 YELLOW Ignition ( + ) Locate the vehicle’s ignition wire at the ignition switch. Verication:This wire registers voltage when the key is turned to the ON (or RUN) position. The voltage does not drop out when the key is turned to the START (or CRANK) position.Connect the YELLOW wire to the vehicle’s Ignition wire.
20 2014 VOXX Electronics Corporation. All rights reserved. 3 PURPLE Door Trigger Input ( + ) Locate the vehicle’s dome light or door pin switch wire. Verication:Thiswirewillregisterpositivevoltage(POS)whenthedoorisopenedand the interior light is on. This wire will register ground or “0” Volts when the door is closed and the interior light is off. Connect the PURPLE wire to the vehicle’s positive door input wire(s).NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide 4 RED Parking Light Polarity 5 WHITE Parking Light Output ( + / - ) Locate the vehicle’s parking light wire at the vehicle light switch. Verication:This wire will register positive voltage or ground when the vehicle parking light switch is turned to the ON position.These wires are the COMMON and NORMALLY OPEN contacts of the on-board parking light relay. If the vehicle’s parking lights are a +12 volt switched system, connect the RED wire to a fused +12 volt battery source, and connect the WHITE wire to the vehicle’s parking light wire. If the vehicle’s parking lights are a chassis ground switched system, connect the RED wire to a chassis ground source, and connect the WHITE wire to the vehicle’s parking light wire. 6 BROWN Door Trigger Input ( - ) Locate the vehicle’s dome light or door pin switch wire. Verication:Thiswirewillregisterground(NEG)whenthedoorisopenedandtheinterior light is on. This wire will register positive voltage when the door is closed and the interior light is off. Connect the BROWN wire to the vehicle’s negative door input wire(s).NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide
21PROPLME Install Guide rev A. 7 RED / WHITE 12 Volt Battery Input ( + ) Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch. Verication:This wire will register voltage in all positions of the ignition switch.Connect the RED/WHITE wire to the constant 12 Volt battery wire.NOTE: Remove the in-line fuse until all connections are made. 8 ORANGE Armed Output ( - ) 500mA This wire will show ground when the system is armed. This wire is used for controlling a starter interrupt relay, window modules or other additional sensors.NOTE: Can also be used as a Disarmed Output ( - ) for a normally open starter kill. Setting must be changed in option programming.6 PIN INPUT / OUTPUT HARNESS 2 DK. GREEN Instant Trigger Input ( - ) This wire is a ground input for an external sensor, trunk pin or secondary pin switch. Verication:Thiswire,whenconnected,willtriggerthesecuritysystem. 3 BLACK / WHITE Horn Output ( - ) 300mA Locate the vehicle’s horn wire at the steering column. Verication:This wire will register at positive voltage and register ground when the horn switch is pressed.Connect the BLACK/WHITE wire to the vehicle’s horn wire. 1 OPEN No Wire Connection
22 2014 VOXX Electronics Corporation. All rights reserved.5 GREEN / WHITE Illuminated Entry Output ( - ) 200mA This wire provides a 200mA output for 30 seconds when the system is disarmed and a continuous output when the system is triggered. Verication:This wire will register positive voltage or ground when the vehicle’s dome light is turned ON. Locate the vehicle’s dome light or pin switch wire.6 DK. BLUE Trunk Release Output ( - ) 300mA This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories such as trunk release.• To Activate press and hold UNLOCK for 2 seconds. Verication:This wire will register either positive voltage or ground when the trunk release is activated.Locate the vehicle’s trunk release wire at the trunk release switch.5 PIN INPUT HARNESS1 BLUE Trunk Shunt Input ( + ) This Wire, when activated, will suspend all security zones from triggering the system until 5 second after the shunt input OR the last trigger input clears. 4 LT. GREEN Instant Trigger Input ( - ) Install the supplied Hood Pin Switch and connect to the LT GREEN wire. Verication:Thiswirewhenconnectedwillregistergroundwhenthevehicle’shoodisopened.Connect the LT GREEN wire to the hood pin.NOTE: Be sure to loom the wire, and seal the grommet.
23PROPLME Install Guide rev A.3 RED / YELLOW Disarm Input This wire will DISARM the security system when a ( + ) pulse is applied to it from an external device such as the vehicle’s factory unlock motor wire.2 RED / BLACK Disarm Input 2 This wire will prevent the system from disarming the security system when a POS or NEG pulse is applied to it from an external device. This will prevent the system from disarming if it is pulsed at the same time as the RED (Disarm Input) wire. For example: To prevent the system from disarming from the switch on the door connect this wire to the unlock switch or passenger unlock motor wire NOTE: Only required if using the factory keyless entry transmitter to ARM/DISARM this system.5 GREEN Arm Input This wire will ARM the security system when a ( + ) pulse is applied to it from an external device such as the vehicle’s factory lock motor wire.4 GREEN / BLACK Arm Input 2 This wire will prevent the system from arming the security system when a POS or NEG pulse is applied to it from an external device. This will prevent the system from disarming if it is pulsed at the same time as the GREEN (Arm Input) wire. For example: To prevent the system from arming from the switch on the door connect this wire to the lock switch or passenger lock motor wire NOTE: Only required if using the factory keyless entry transmitter to ARM/DISARM this system.
24 2014 VOXX Electronics Corporation. All rights reserved.3 PIN DOOR LOCK HARNESS 1 RED / BLACK 2nd Unlock Output ( - ) 200mA 2 GREEN Unlock Output ( - ) 200mA 3 Red Lock Output ( - ) 200mA Negative Switching and Negative Switching with 2-step unlock feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verication: These wires will register ground when the lock and unlock switches are activated. Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door. Verication:This wire will rest at ground and register positive voltage when the driver’s door is unlocked. Connect the RED and GREEN or RED/BLACK wires shown in the diagram below. NOTE: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect the relay as shown in the diagram below to unlock the driver’s door on the rst press of unlock.
25PROPLME Install Guide rev A.LockUnlock8787a86 8530Vehicle Door Lock Control RelaysRED (-) Lock OutputGREEN (-) Unlock Output orRED/BLACK 2nd UnlockOutput for 2 Step UnlockFor 2 Step Unlock:Fused +12 Volt Battery SouceGREEN (-) Unlock OutputFrom Keyless Entry Module or Door Unlock Relay Drivers Door Unlock Motor WireXCutNegative Locks:
26 2014 VOXX Electronics Corporation. All rights reserved. 1 RED / BLACK 2nd Unlock Output ( - ) 200mA 2 GREEN Unlock Output ( - ) 200mA 3 Red Lock Output ( - ) 200mA Positive Switching and Positive Switching with 2-step unlock feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verication: These wires will register positive voltage when the lock and unlock switches are activated. Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door. Verication:This wire will rest at ground and register positive voltage when the driver’s door is unlocked. Connect the RED and GREEN or RED/BLACK wires shown in the diagram below. NOTE: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all vehicle doors on the second press of unlock. Two additional SPDT relays (not supplied) are required. Connect the relays as shown in the diagram below to unlock the driver’s door on the rst press of unlock.
27PROPLME Install Guide rev A.LockUnlock8787a86 85308787a86 85308787a86 8530Vehicle Door Lock Control RelaysFused +12 Volt Battery SouceFused +12 Volt Battery SouceRED (-) Lock OutputGREEN (-) Unlock Output orRED/BLACK 2nd UnlockOutput for 2 Step UnlockFor 2 Step Unlock:Fused +12 Volt Battery SouceGREEN (-) Unlock OutputFrom Keyless Entry Module or Door Unlock Relay Drivers Door Unlock Motor WireXCutPositive Locks:
28 2014 VOXX Electronics Corporation. All rights reserved. 1 RED / BLACK 2nd Unlock Output ( - ) 200mA 2 GREEN Unlock Output ( - ) 200mA 3 Red Lock Output ( - ) 200mA One Wire Negative Multiplexed and One Wire Negative Multiplexed with 2 step Unlock Feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verication: This wire will show variable ground when the switch is activated. Please consult the Vehicle Wire Color and Location Chart for specic resistor values for the vehicle. Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door. Verication:This wire will rest at ground and register positive voltage when the driver’s door is unlocked. Connect the RED and GREEN or RED/BLACK wires shown in the diagram below using (2) SPDT relays (not supplied).NOTE: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect the relay as shown in the diagram below to unlock the driver’s door on the rst press of unlock.
29PROPLME Install Guide rev A.LockUnlock8787a86 8530Vehicle Door Lock Control RelaysRED (-) Lock OutputGREEN (-) Unlock Output orRED/BLACK 2nd UnlockOutput for 2 Step UnlockFor 2 Step Unlock:Fused +12 Volt Battery SouceGREEN (-) Unlock OutputFrom Keyless Entry Module or Door Unlock Relay Drivers Door Unlock Motor WireXCutMultiplex Locks:8787a86308787a863085 85Fused +12 VoltBattery SourceGroundResistor
30 2014 VOXX Electronics Corporation. All rights reserved. 1 RED / BLACK 2nd Unlock Output ( - ) 200mA 2 GREEN Unlock Output ( - ) 200mA 3 Red Lock Output ( - ) 200mA One Wire Positive Multiplexed and One Wire Multiplexed With 2-step Unlock Feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verication: This wire will show variable positive voltage when the switch is activated. Please consult the Vehicle Wire Color and Location Chart for specic resistor values for your vehicle. Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door. Verication:This wire will rest at ground and register positive voltage when the driver’s door is unlocked. Connect the RED and GREEN or RED/BLACK wires shown in the diagram below using (2) SPDT relays (not supplied).NOTE: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect the relay as shown in the diagram below to unlock the driver’s door on the rst press of unlock.
31PROPLME Install Guide rev A.LockUnlock8787a86 8530Vehicle Door Lock Control RelaysRED (-) Lock OutputGREEN (-) Unlock Output orRED/BLACK 2nd UnlockOutput for 2 Step UnlockFor 2 Step Unlock:Fused +12 Volt Battery SouceGREEN (-) Unlock OutputFrom Keyless Entry Module or Door Unlock Relay Drivers Door Unlock Motor WireXCutMultiplex Locks:8787a86308787a863085 85Fused +12 VoltBattery SourceResistor
32 2014 VOXX Electronics Corporation. All rights reserved. 1 RED / BLACK 2nd Unlock Output ( - ) 200mA 2 GREEN Unlock Output ( - ) 200mA 3 Red Lock Output ( - ) 200mA Reverse Polarity (5-Wire Door locks) and Reverse Polarity with 2-step Unlock: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verication: These wires will rest at ground and register positive voltage when the lock and unlock switches are activated. Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door. Verication:This wire will rest at ground and register positive voltage when the driver’s door is unlocked. Connect the RED and GREEN or RED/BLACK wires shown in the diagram below using (2) SPDT relays (not supplied). NOTE: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect the relays as shown in the diagram below to unlock the driver’s door on the rst press of unlock.
33PROPLME Install Guide rev A.LockUnlock8787a86 85308787a86 85308787a86 8530Fused +12 Volt Battery SouceFused +12 Volt Battery SouceRED (-) Lock OutputGREEN (-) Unlock Output orRED/BLACK 2nd UnlockOutput for 2 Step UnlockFor 2 Step Unlock:Fused +12 Volt Battery SouceGREEN (-) Unlock OutputFrom Keyless Entry Module or Door Unlock Relay Drivers Door Unlock Motor WireXCutReverse Polarity Locks:XCutXCutTo Door Lock MotorTo Door Lock Motor
34 2014 VOXX Electronics Corporation. All rights reserved. 1 RED / BLACK 2nd Unlock Output ( - ) 200mA 2 GREEN Unlock Output ( - ) 200mA 3 Red Lock Output ( - ) 200mA Adding Door Actuators: After installing door actuators, (not supplied). Connect the RED and GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).308787a86 85Fused +12 VoltBattery SourceDoor Lock Actuator308787a86 85ChassisGroundChassisGround RED (-) Lock Output GREEN (-) Unlock OutputFused +12 VoltBattery SourceM
35PROPLME Install Guide rev A.ACCESSORY CONNECTORS6 Pin LED / Override Pod The status LED / override button should be mounted in a visible and easily accessible location on the driver’s dashboard area. Route the harness and plug the 6 pin connector into the module.4 Pin Telematic Port This 4 pin port is used for connecting the telematic accessories such as Car Connection, CarLink, or PursuiTrak.4 Pin DBI - Data Bus Interface Port This 4 pin port is used for Flashlogic Door Lock and Transponder Databus Interfaces to communicate with the vehicle’s Databus. When using the DBI port to control the Flashlogic Door Lock and Transponder Interface modules the following options may be available. Please refer to the D2D (Data to Data) function list available per vehicle on the tech service web site. Door Trigger Trunk/Hatch Open Keyless Entry Control Dome Light Supervision Factory Alarm Arm / Disarm Manual Arm / Disarm Inputs (factory keyless controls system)
36 2014 VOXX Electronics Corporation. All rights reserved.Factory Alarm TriggerThe ITS Factory Alarm Trigger is active 30 seconds after the ignition is turned off and the factory alarm has been set. When a heavy impact is detected the ITS will pulse the vehicle’s door trigger wire to active the factory alarm.Optional Warn AwayThe optional Warn-Away Trigger is active 30 seconds after the ignition key is turned off and the dome light shuts off after exiting the vehicle. When a light impact is detected the system will briey honk the vehicles horn. If at any time a door is opened (dome light “on”), the Warn-Away Trigger will be bypassed until the ignition key is cycled “ON” and “OFF”. This feature prevents the Warn-Away chirps of the vehicle’s horn when the customer/user enters the vehicle. The Warn-Away Trigger will reactivate when the ignition key is cycled “ON” and “OFF” again.I.T.S. ACTIVATIONI.T.S. - INTERIOR THEFT SENSOR FUNCTIONALITYI.T.S. - Interior Theft Sensor IntroductionThe system may be used as an I.T.S. (Interior Theft Sensor) and when doing so it is de-signed to honk the horn if a light impact is detected or trigger the vehicle’s factory security system if a harder impact is detected.Note: The vehicle MUST have a factory security system that is triggered by opening the vehicle’s door.Option #11 must be changed in the feature programming bank for the system to function as the I.T.S.. This will also happen automatically when transitioning from Lot mode to Green mode using an ACM Keypad.The factory keyless remote can also be used to arm/disarm the I.T.S. sensor as long as the standard arm & disarm input wires are connected to the vehicle. You may also program an aftermarket remote transmitter to the unit as well.
37PROPLME Install Guide rev A.I.T.S. Harness ConnectionsDK BLUE - Factory Alarm Trigger: Connect this to a wire which triggers the vehicle’s factory alarm system such as the door ajar, hood or trunk wire.PURPLE and BROWN - Door Inputs ( + / - ): Connect one of these wires to the vehicle’s dome light wire.RED/WHITE - +12 Volt Input: Connect this wire to constant +12 volt source.BLACK - Ground Input: Connect this wire to chassis ground.YELLOW - Accessory Input: Connect this wire to +12 volt accessory source.BLACK/WHITE - Warn Away Horn Output: Connect this wire to the vehicle’s horn wire.NOTES:The ITS uses the PURPLE or BROWN (Door Input) to DISARM the optional Warn-Away feature. The PURPLE or BROWN must sense all of the doors for the ITS to DISARM properly. It is recommended to only use the Warn-Away feature with vehicle’s that have an “ALL” door trigger output in the vehicle. Valet ModeValet Mode deactivates both the optional Warn-Away and Factory Alarm Trigger. To turn Valet Mode ON:Turn the ignition key to the ON position and press and hold the valet button until the LED turns on solid.To turn Valet Mode OFF:Turn the ignition key to the ON position and press and hold the valet button until the LED turns off.
38 2014 VOXX Electronics Corporation. All rights reserved.SYSTEM POWER-UP PROCEDURE1. After all connections are complete, turn the vehicle’s ignition key to the ON position2. Insert the 5 Amp fuse into the respective fuseholder.3. Turn the ignition key to the OFF position.MOUNTING THE MODULE / FINISHING INSTALLATION Mount the module to a brace or wire harness under the dash. The module and harnesses must be clear of moving parts. Installation Complete.
39PROPLME Install Guide rev A. Feature Bank 1, 3 Chirps1 - Security Function: Controls security functionality - ON / OFF. Note: In Lot Mode all security triggers will be ignored no matter what setting is selected. ON - Full security functionality. OFF - The security system does not trigger. All other convenience features operate as normal. ON, Warn Away Disabled - Full security functionality with the warn-away function of the shock sensor disabled. 2 - Passive Locks: Determines manual or automatic locking of the vehicle’s doors. Passive - Automatically locks the vehicle’s doors 1 minute after the last door is closed. Active - Requires use of the transmitter to lock the vehicle’s doors.3 - Silent Choice: Controls when the normal arm/disarm chirps of the security system will sound. (Feature #8 must be ON) ON - Silent arming/disarming upon rst press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/ unlock buttons. OFF - normal arm/disarm chirps upon the rst press of lock/unlock.4 - Passive/Active Arming: Determines manual or automatic locking of the vehicle’s doors. Passive - Automatically arms the security system 1 minute after the last door is closed. Active - Requires use of the transmitter to arm the security system.5 - Siren / Horn: This feature selects the output type for the BLACK/WHITE wire during the security trigger cycle. Siren - 30 second constant output. Horn – 30 second pulsed output.6 - Door Trigger Delay: Selectable instant or delayed trigger cycle when security is trig-gered by the door input. Instant – Door input instantly triggers alarm sequence. 15 Second - Door input delays triggering the alarm sequence for 15 seconds. 7 - Arm Input 2 Polarity: Select the input polarity as positive or negative.FEATURE DESCRIPTIONS
40 2014 VOXX Electronics Corporation. All rights reserved.8 - Arm/Disarm Chirps: Controls the normal Arm / Disarm chirps. NOTE: This feature must be ON to use system chirps even with the silent choice feature enabled ON - Arm / Disarm chirps function as normal. OFF - All Arm / Disarm chirps are disabled. ON Including ITS Mode - Arm / Disarm chirps function as normal including when in ITS Mode.9 - Door Lock Output Timing: Controls the timing of the RED and GREEN lock output wires. 0.9 Second - Single 0.9 second lock pulse, single 0.9 second unlock pulse. 3 Seconds - Single 3 second lock pulse, single 3 second unlock pulse. 0.9 Second Lock, Double Pulse Unlock - Single 0.9 second lock pulse, double 0.9 second unlock pulse. 0.75 Second - Single 0.75 second lock pulse, single 0.75 second unlock pulse. 10 - Ignition Controlled Locks: Control of door locks when the ignition is cycled ON or OFF. All (Lock & Unlock) - Doors lock when ignition is turned on and unlock when ignition is turned off. Lock Only - Doors lock when ignition is turned on Unlock Only - Doors unlock when ignition is turned off. OFF - Door locks not activated by ignition.11 - DK BLUE Wire Output: This feature controls the type of output for the DK BLUE wire. Setting this feature to ITS Function will change the functionality of the entire sys-tem, refer to ITS functionality of the install guide. Trunk - 1 second pulsed output. ITS Function - ITS function, warn-away and full trigger. ITS Function, Warn Away Disabled - ITS function with full trigger only12 - Disarm Input 2 Polarity: Select the input polarity as positive or negative.13 - Horn Output Timing: Control the minimum horn pulse time in milliseconds, some vehicle will require a longer pulse to activate the factory horn. 10mS 16mS 30mS 40mS 72mS14 - Real Panic Sound: Controls the horn output when the system is triggered. ON - Randomized horn honks when panic/security is triggered. OFF - Standard pattern horn honks when panic/security is triggered.
41PROPLME Install Guide rev A.15 - Orange Wire Output: Controls the output of the orange wire. This wire will either supply a ( - ) output when armed OR disarmed. ( - ) Armed Output - Supplies a constant negative out while the system is armed ( - ) Disarmed Output - Supplies a constant negative out while the system is disarmed16 - Arming Delay: Control the type of arming; standard, delayed or armed with vehicle remote started. OFF - No delay when arming, normal security functionality. 45 Seconds - Delays the arming process for 45 seconds when armed using the ARM/DISARM INPUTS, during this time the system will be disarmed if the ignition is turned ON. No delay is added if using an aftermarket transmitter to arm the system Factory R/S Option - For use with vehicles with a FACTORY INSTALLED Remote Start. If the ignition comes on within 6 seconds of arming the system, the system will ignore ALL security inputs until 5 seconds after ignition clears OR any remaining inputs clear after ignition has cleared. 17 - GREEN/WHITE Output Wire: Controls the GREEN/WHITE output type. Illuminated Entry - Supplies a constant output for 1 minute. Factory Disarm - Single 1 second puled output upon disarming the system. 18 - Lot Alert: Available in Lot Mode only - Toggle Lot Mode notication chirps ON/OFF. OFF - No notication chirps ON - 5 short low volume chirps each time the ignition is turn ON. 19 - Lot Mode Passive Arming Timers; TX Disarm / Ignition: Available in Lot Mode only - Change the passive arming timers when the system is unlocked or the ignition is turned on. 5 / 30 Minute - 5 minute timer when doors have been unlocked / 30 minute timer after the ignition has been turned OFF. 1 / 1 Minute - 1 minute timer when doors have been unlocked / 1 minute timer after the ignition has been turned OFF.
42 2014 VOXX Electronics Corporation. All rights reserved.ADDITIONAL FEATURES Arm System with Shock Senor Bypassed (Aftermarket TX only)1. Press Lock button to arm system2. Within 5 seconds press the Trunk OR Find/Panic button. Parking Lights/Horn will ash/chirp 2 times.  AttemptedIntrusionIdenticationPressing UNLOCK after a full 30 second trigger cycle has completed, the horn will honk 4 times and the LED will ash a number of times to indicate which input triggered the alarm. Turning on the ignition or pressing the valet/override button will reset the LED ashes, pressing the valet/override button will also honk the horn to match the LED ashes before it is reset.Number of ashes: 1 - Interior Theft Sensor (Shock Sensor) 2 - Door Input 3 - Hood Input 4 - Trunk Input 5 - Ignition Valet Mode - Consumer Modes OnlyTo engage valet mode:1. Turn the ignition key ON. 2. Press and hold the valet button until the LED status light turns on solid indicating that the system is in valet mode.3. Release the valet button.4. When valet mode is activated all security functions will be disabled.To disengage valet mode:1. Turn the ignition key ON.2. Press and hold the valet button until the LED status light turns off indicating that the system has exited valet mode. DeletingArm/Disarmnoticationchirps1. Turn the ignition ON then OFF.2. Press and release the valet button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.
43PROPLME Install Guide rev A.System Function Lot ModeACM Keypad TXConsumer ModeAftermarket TX Operation MethodLock Doors / Arm System Lock Lock Press and ReleaseUnlock / Disarm(consumer Mode)Unlock Press and ReleaseUnlock / Unlock 2 / Disarm(Lot Mode) Unlock Press and Release2 Step UnlockUnlockPress and Release 2 times (within 5 sec)Unlock & Unlock 2 activate at the same timeTrunk TrunkPush and Hold (2 Sec) Trunk / DisarmUnlockPush and Hold (2 Sec) Car Finder (Progressive)Find/PanicFind/PanicPress and Release, 3 volume levels for Chirp - 1st press - Low(within 3 sec of 1st press) 2nd press - Medium(within 3 sec of 2nd press) 3rd press - LoudPanicFind/PanicFind/PanicPush and Hold (1 Sec) Shock BypassLock - Trunk-or-Lock - Find/PanicPress and Release Lock then within 5 sec. Press Trunk-or-Press and Release Lock then within 5 sec. Press Car FindAFTERMARKET TRANSMITTER FUNCTIONS Dome Light Delay/Theater Lighting Programming The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the dome light delay and add 2 seconds before arming.1. Close all doors with ignition off. 2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK. The LED will light solid to indicate the system has entered DOME DELAY LEARN MODE.3. Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the learning mode.4. The LED will begin to ash indicating the system has exited the learning mode and is now armed.
44 2014 VOXX Electronics Corporation. All rights reserved.FCC COMPLIANCEThis device complies with Part 15 of the FCC rules and with RSS-210 ofIndustry Canada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including any interferencethat may cause undesired operation.Warning!Changes or modications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment. VOXX Electronics Corporation.150 Marcus Blvd., Hauppauge, New York 11788Customer Service 1-800-225-6074WWW.CODE-ALARM.COMPLTX4

Navigation menu