Nutek NTRNC Transceiver User Manual AL 1860 EDPB operation guide indd
Nutek Corporation Transceiver AL 1860 EDPB operation guide indd
Nutek >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2348153 |
| Application ID | 5tJqNm2F+IiT3B8qR8VMUA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 98.61kB (1232646 bits) |
| Date Submitted | 2014-08-06 00:00:00 |
| Date Available | 2014-08-07 00:00:00 |
| Creation Date | 2017-10-21 17:27:43 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-21 17:27:43 |
| Document Title | AL-1860-EDPB operation guide.indd |
| Document Creator | Adobe InDesign CS5.5 (7.5.3) |
AL-1860-EDPB Deluxe 2-way Alarm & Remote Start w/ BLADE Technology July 8, 2013 Operation Guide Temporary cover. Color cover is in a separate ile. Table Of Contents Controller & Transmitter Overview 3 The 2-Way Controller 3 The 1-Way Transmitter 3 Controller & Transmitter Functions 3 Other Remote Start Features 7 Low Battery/Low Temp Automatic Starting 7 Turbo Timer Feature 8 Pit-Stop Feature 8 Manual Transmission Starting 8 Security System Features 8 Last Door Arming 8 Automatic Rearming 9 Pre-Warn Detection 9 When The System Triggers 9 Using The Valet Switch 10 Emergency Override 10 Valet Mode 10 SecureCode 10 The Status Light 11 Multi-Car Operation 12 Selecting CAR #1 or CAR #2 12 Controller Options 12 LCD Screen Icons 12 In-Range Indicator 12 Setting The Clock 12 Changing remote start melodies 13 Power Save Mode 13 Selecting Melody & Vibrate modes 13 Parking Timer & Remote Start Timer 13 Button Lock 13 Anti-Carjacking Protection 14 Programming Controllers/Transmitters 15 Programming Features 15 User Programmable Features 16 Installer Programmable Features 19 Programmable Features Matrix 23 Controller & Transmitter Overview ThE 2-WAy COnTROLLER Controller part number: #159 (w/ 2 CR2032 batteries) 159-03 Call your dealer or visit www.caralarm.com to order replacement transmitters. “start” button Controller battery replacement: Slide the back cover (do not pry up) off the back of the case in the direction of the arrow Release the small black battery clips and pull up on the battery from the inside edge (closest to the other battery) Sometimes a small tool or the edge of the back cover is helpful in gently prying up the batteries Insert the new batteries, making sure to insert the edge beneath the “+” terminal irst. Slide the back cover back onto the case ThE 1-WAy TRAnSmiTTER Transmitter part number: #1411 (w/ 2 CR2016 batteries) 1411-03E “trunk” button programming button “unlock” button “lock” button “lock” button “unlock” button Call your dealer or visit www.caralarm.com to order replacement transmitters. Transmitter battery replacement: Remove the small screw from the lower back case, and separate the transmitter halves Replace the battery with the same type and reassemble the transmitter case “start” button “trunk” button Controller & Transmitter Functions LOCK / ARm: Press and release the “LOCK” button • THE SIREN WILL CHIRP & THE PARKING LIGHTS WILL FLASH ONCE • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL SHOW THE LOCK/ARM ICON AND BEEP ONCE nOTE: PRESSinG LOCK TWiCE in 5 SECOnDS STARTS ThE PARKinG TimER. ThE CLOCK WiLL ChAnGE TO 0:00 AnD START COunTinG in minuTES & hOuRS. Controller & Transmitter Functions (cont’d) unLOCK / DiSARm: Press and release the “UNLOCK” button • THE SIREN WILL CHIRP TWICE & THE PARKING LIGHTS WILL FLASH TWICE, THEN ILLUMINATE FOR 30 SECONDS • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL SHOW THE UNLOCK/ DISARM ICON AND BEEP TWICE TRunK RELEASE / ChAnnEL 2: Press the “TRUNK” button for 3 seconds • THE SYSTEM WILL DISARM AND THE TRUNK WILL OPEN (IF EQUIPPED) • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL PLAY THE TRUNK RELEASE ANIMATION AND BEEP TWICE. REmOTE START: Press and release the “START” button twice within 5 seconds (see user feature #8 for additional options) x2 • THE PARKING LIGHTS WILL FLASH ONCE AND THE STATUS LIGHT WILL FLASH RAPID • THE SYSTEM WILL TURN ON THE IGNITIONS AND PROCEED TO START THE ENGINE • ONCE THE ENGINE IS RUNNING, THE PARKING LIGHTS WILL FLASH EVERY 15 SECONDS AND THE STATUS LIGHTS WILL FLASH SLOW • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL PLAY THE REMOTE MELODY AND SHOW THE REMOTE START ICON • THE CLOCK WILL CHANGE TO 0:00 TO START THE REMOTE START TIMER IT WILL TIME HOW LONG THE ENGINE RUNS IN MINUTES & HOURS • If the engine stalls, the system will make up to 3 more attempts • Each time you park, set the climate controls to give you the desired interior temperature when you use the remote start (continued on pg 5) Controller & Transmitter Functions (cont’d) The engine will run for the preset run time (see user feature #1) • Run Time Extender: Press the “START” button one time during remote start to restart the engine run timer The timer will restart at “0:00” nOTE: This can only be used once per remote start cycle. The controller will also give you “run time expiration” warning (2 chirps) 1 minute before the remote start cycle ends. • If you decide not to drive your vehicle, you can turn off the remote start using the same method to turn it on (Default = press “START” twice in 5 seconds) nOTE: if user feature #8 is programmed for 1 press, the 1st press = Run Time Extender so an additional press is required. • Upon entering the vehicle during remote start mode, turn the ignition key to the “ON/RUN” position (nOT START!!) When you press the brake pedal, the remote start will turn off allowing the ignition key to take over ChAnnEL 3: Press and hold the “TRUNK” & “START“ buttons for 3 seconds • YOUR SYSTEM WILL ACTIVATE THE CHANNEL 3 OUTPUT • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL SHOW “CH3” ON THE CLOCK DISPLAY ChAnnEL 4: Press and hold the “LOCK” & “TRUNK” buttons for 3 seconds • YOUR SYSTEM WILL ACTIVATE THE CHANNEL 4 OUTPUT • THERE IS NO 2-WAY CONFIRMATION FOR THIS FUNCTION ChAnnEL 5: Press and hold the “UNLOCK” & “START“ buttons for 3 seconds • YOUR SYSTEM WILL ACTIVATE THE CHANNEL 5 OUTPUT • THERE IS NO 2-WAY CONFIRMATION FOR THIS FUNCTION Controller & Transmitter Functions (cont’d) PAniC: Press and hold the “LOCK” or “UNLOCK” button for 3 seconds • THE SIREN/HORN WILL SOUND, THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR UNLOCK DEPENDING WHICH BUTTON IS PRESSED OR SiLEnT ARm / DiSARm: Press and release the “TRUNK” button twice in 5 seconds • THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL LOCK/ARM OR UNLOCK/DISARM DEPENDING ON THE CURRENT SYSTEM STATUS • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL SHOW THE LOCK/ ARM OR UNLOCK/DISARM ICON x2 SEnSOR ByPASS: Press and release the “TRUNK” button within 5 seconds of locking/arming the alarm system • THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE THE SENSOR IS BYPASSED • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL ALSO CHIRP ONCE & DISPLAY THE SENSOR ICON LOW VOLTAGE/TEmP AuTO START: Press and release the “START” button within 5 seconds of locking/arming the system • THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE THE LOW VOLT/LOW TEMP(15 DEGREE ONLY) AUTOSTART IS ACTIVATED SEE PAGE 7 FOR MORE INFO • UPON RECEIVING CONFIRMATION, THE CONTROLLER WILL CHIRP ONCE AND THE CLOCK WILL READ “RS AUTO” EVERY 5 SECONDS Controller & Transmitter Functions (cont’d) REmOTE VALET: Press “LOCK” then “UNLOCK” then “TRUNK” + “START” within 5 seconds • THE SYSTEM WILL ENTER VALET MODE SEE PAGE 10 FOR MORE INFO ON VALET MODES • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL SHOW THE VALET ICON TO EXiT VALET ViA REmOTE, REPEAT ThESE STEPS AuXiLiARy FunCTiOnS 1-4: The actual operation of these functions will vary from car to car They are designed to operate extra vehicle functions like automatic sliding doors or motorized hatches Aux 1-4 are virtual outputs only available on certain vehicles when this system is integrated with the vehicle’s data network. Consult with your installer to ind out if any of these functions are available for your vehicle. If so, conirm each operation with the controller and write each function in the blank spaces provided below - Auxiliary 1 Function (___________________): To activate this function, press and release the “trunk” and “start” buttons simultaneously) - Auxiliary 2 Function (___________________): To activate this function, press and release the “lock” and “trunk” buttons simultaneously) - Auxiliary 3 Function (___________________): To activate this function, press and release the “unlock” and “start” buttons simultaneously) - Auxiliary 4 Function (___________________): To activate this function, press and release the “unlock” and “trunk” buttons simultaneously) Other Remote Start Features LOW BATTERy/LOW TEmP AuTOmATiC STARTinG This feature will automatically start the engine if the vehicle battery drops below 11 volts or the interior temperature drops to 15 (or 32) degrees fahrenheit You must activate these features each time you park your car to use them They can be activated one of two ways: method 1 - Valet Switch • Turn the ignition switch “on”, then “off” (engine not running), and within 7 seconds press the valet switch twice If there is a 2 second delay without additional valet button presses, the horn will honk 3 times activating low voltage start mode • To activate low temp starting, enter low voltage start mode as described above then, immediately after the horn honks, press the valet switch 1 time (15 degrees) or 2 times (32 degrees) within 5 seconds. The horn will honk to conirm your selection. method 2 - With The Controller (Low Volt + Low Temp - 15 Degrees Only) • Within 5 seconds of pressing LOCK, press the START button. You will get one chirp and the 2-way controller will alternate between “ARM” and “RS AUTO” nOTE: When low temp start mode is activated, low voltage start is also activated These features will operate once every two hours until the ignition key is turned “ON” Other Remote Start Features (cont’d) TuRBO TimER FEATuRE It is typically recommended that vehicles equipped with turbocharged engines allow the engine to idle after driving to cool the turbocharger When Installer Programmable Feature #10 is ON, the system will automatically keep the engine running as follows: • With the engine running, hold the brake pedal and engage the parking brake When the brake pedal is released, the system will keep the engine running for the programmed time (1, 2, or 3 minutes), and then automatically turn it off • The system may be locked while the engine is running. Turbo Timer can be prevented from engaging, or “bypassed” if desired, by turning the engine off before engaging the parking brake, or if it’s already engaged, step on the brake pedal to turn the engine off PiT-STOP FEATuRE This feature allows you to leave your engine running for making quick errands To use this feature, have the engine running normally from the ignition switch and your foot off the brake pedal. Press the Valet Switch twice; the parking lights will lash and the horn will chirp 5 times Turn the key off and the engine will remain running for the programmed run time mAnuAL TRAnSmiSSiOn STARTinG Remote starting with a manual transmission requires a different installation method and installer feature #11 must be turned on Also, a setup procedure that ensures the transmission was left in neutral must be performed each time you leave your vehicle and intend to use remote start later Perform these steps: 1) With the engine running, hold the brake pedal, apply the parking brake, then release the brake pedal 2) Use the transmitter as if you were activating remote start (default: press START twice). The green status light will start to lash slow. 3) Turn off the ignition key and exit the vehicle 4) Press LOCK on the transmitter The engine will shut down (unless turbo timer is on) and the status light will lash green every 2 seconds to indicate it is ready to be remote started nOTE: manual transmission starting is canceled if you enter the vehicle after performing the setup procedure. Security System Features LAST DOOR ARminG This system can be conigured to arm automatically when all the vehicle’s doors are closed (see user feature #9) When this feature is utilized, the siren/horn will chirp once when all of the doors are closed At that point, it will start a 30 second countdown (indicated by a fast lashing status light). After 30 seconds, the system will arm (and lock the doors if conigured to do so). During the 30 second arming delay, if a point of entry is opened, the countdown will pause until all entry points are closed again Turning ON the ignition key will cancel the last door arming sequence until the key is turned off and the doors are all closed once again Security System Features (cont’d) AuTOmATiC REARminG This automatically rearms the alarm if the system is disarmed from the remote (see user feature #10) When disarmed by remote, the system will start a 90 second countdown (fast lashing status light) to arm the system. This is useful if the controller accidentally disarms the system when it’s kept in a purse or pocket where other items could potentially press the buttons ENHANCED AUTO REARM allows you to cancel the countdown by pressing UNLOCK a second time within 5 seconds of the irst press to disarm the alarm PRE-WARn DETECTiOn This system’s impact sensor is designed, in addition to detecting a full impact, will warn away potential violators when it detects a light impact to the vehicle The system will respond by chirping the siren/horn 3 times and locking the doors This is very useful when an intruder attempts to unlock the door with “slim jim” types of devices WhEn ThE SySTEm TRiGGERS If the system were to be compromised while armed, it will trigger by sounding the siren/horn and lashing the parking lights for 30 seconds (programmable). At this point you will also be notiied on the controller as to which zone is violated (if in range of the system) When disarming the system after a trigger event, the siren/horn will chirp 4 times and the parking lights will lash 4 times instead of the standard 2 times. LOCK On TRiGGER: If a door is opened when the system is triggered, it will wait until the door is closed again, then lock the doors This patented feature is useful to further deny a thief of further access to the vehicle STORm SAFE mODE: When the system is triggered, pressing the “UNLOCK” button will stop the alarm from sounding but will leave the doors locked This function is useful if you have a false triggering situation due to violent weather ZOnE ViOLATiOn RECALL: The system is capable of telling you which zones were triggered last. The system’s status light will lash to indicate which zone was triggered. This occurs during the alarm cycle AND after disarming The system will store the last triggered zone until the vehicle’s ignition key is turned on See “The Status Light” section of this manual for further explanation of this feature nuiSAnCE PREVEnTiOn: If the system prewarns 5 times within 15 minutes, it will bypass the zone for the remainder of the 15 minutes before rearming the pre-warn zone Additionally, if a full trigger zone is left open, the system will trigger a total of 3 times before bypassing the zone Once the zone is closed again, it will re-arm that zone using The Valet Switch EmERGEnCy OVERRiDE If you were to lose or break your controller, you’d need to perform an emergency override to disarm the system and use your vehicle To do so, use the following steps: STEP 1 - Enter the vehicle (the alarm should sound) STEP 2 - Turn the ignition key to the “ON” position STEP 3 - Press the valet switch (located in the window-mount antenna) once NOTE: Enter your SecureCode at this time if programmed via user feature #13 STEP 4 - Turn the ignition key “OFF” VALET mODE Valet mode completely disables all security & remote start functions Keyless entry is still operable To enter valet mode, perform the following steps: STEP 1 - Disarm the system by remote or by performing an emergency override STEP 2 - Press and hold the valet switch for 2 seconds The system will chirp once and the status light will turn on EXiTinG VALET mODE - Press and release the valet switch once The status light will turn off SECuRECODE SecureCode allows you to customize the number of valet presses required to perform an emergency override This is an extra layer of security that prevents anyone from overriding the alarm even if they have a key to the vehicle SecureCode has 2 stages with the irst requiring 1-9 button valet presses and the second requiring 0-9 valet button presses This gives you 99 possible combinations To program a custom SecureCode, please refer to user feature #13 on Page 18 To perform an emergency override with SecureCode, use the following steps: STEP 1 - With the system armed, enter the vehicle (the alarm will activate) STEP 2 - Turn the ignition switch to the “ON” position STEP 3 - Within 5 seconds of step 2, press the valet switch to enter the irst digit of your programmed code STEP 4 - After a few seconds, the siren will stop sounding and chirp once (conirming stage 1) The siren will then continue sounding STEP 5 - Now, within 5 seconds of step 4, press the valet switch to enter the second digit of your code If the code is correct, the alarm will disarm If the code is entered incorrectly, you must turn the ignition key OFF, then back ON to try again Additionally, if 2 failed attempts are made, the alarm will ignore any further attempts for 2 minutes 10 The Status Light The status lights, located in the window-mount antenna, provide a visual indication of the system’s status SECuRiTy SySTEm STATuS OFF: The alarm is disarmed and not performing any automatic functions On: The alarm is in valet mode FLAShinG SLOW: The alarm is armed and monitoring all entry points FLAShinG FAST: One of the automatic arming features is in progress AuTOmATiC TRAnSmiTTER VERiFiCATiOn Every time you turn on the ignition key, the status light will lash a number of times equal to the number of transmitters programmed to the system This unique security feature combats potential thieves (valet attendant, mechanic, etc) from adding their own transmitter without your knowledge and accessing your vehicle at a later time ALARm ZOnE ViOLATiOn RECALL If the security system is triggered, upon disarming, the status lights will lash a number of times to indicate exactly which zone(s), has been violated It will store the last 2 violated circuits and continually repeat the lash pattern until the vehicle’s ignition key is turned ON 2 FLAShES: Hood trigger 3 FLAShES: Door trigger 4 FLAShES: Sensor port trigger REmOTE START STATuS FLAShinG SLOW: The engine was remote started successfully and is running FLAShinG FAST: The remote start sequence has begun and is in process of starting the vehicle’s engine 2 FLAShES, PAuSE: The engine is running while the alarm is armed REmOTE START DiAGnOSTiCS The remote start system can also indicate which zone caused the last remote start cycle to end To see this indicator, place the system into alarm valet mode Immediately after the chirp, the status light will lash to indicate which zone violation occured. 1 FLASh: Run time expired 2 FLAShES: Brake pedal was pressed or the hood was opened 3 FLAShES: Engine stalled or a bad tach signal 4 FLAShES: Received transmitter command to stop 5 FLAShES: The neutral safety circuit was triggered 6 FLAShES: The alarm was triggered or low battery voltage 11 multi-Car Operation The controller can operate up to 2 different systems When controlling 2 systems, it will receive all status updates on the currently selected vehicle proile and will receive only trigger alerts for the 2nd vehicle You can switch from one car to the other at anytime Use the following steps to change vehicles SELECTinG CAR #1 OR CAR #2 Vehicle #1: Press the “P” and “LOCK” buttons for 1 second to select Car #1 The controller will beep/vibrate once and the clock will change to “CAR 1” Vehicle #2: Press the “P” and “UNLOCK” buttons for 1 second to select Car #2 The controller will beep/vibrate twice and the clock will change to “CAR 2” Controller Options LCD SCREEn iCOnS melody/Vibrate Battery Level Clock / Timer Sensor Trigger Remote Start Shutdown Door Trigger hood Trigger Remote Start indicator Carjack mode Valet mode Alarm Status in Range indicator in-RAnGE inDiCATOR All primary commands sent to the system have a conirmation response that is sent to the controller to indicate that the command was successful If the command is successful, the icon will not display the “X” in the middle of the icon If no response is received within a few seconds, the “X” will be displayed indicating that you may be out of range of your system SETTinG ThE CLOCK 1) Press the “P” button for 5 seconds to access the controller features The controller will beep twice 2) Press and release the “P“ button once to select the clock (hour digits will lash). 3) Press the “TRUNK“ button to scroll up or the “START“ button to scroll down 4) Press the “P” button to switch to the minute digits 5) Press the “TRUNK“ button to scroll up or the “START” button to scroll down 6) Wait 10 seconds or press the “P” button for 5 seconds to exit programming The controller will beep once 12 Controller Options (cont’d) ChAnGinG REmOTE START mELODiES The controller has 5 different melodies to choose from for remote start ON and 5 melodies for remote start OFF conirmation. 1) Press the “P” button for 5 seconds to access the controller features The controller will beep twice 2) Press and release the “P“ button 3 times to select the melody settings The clock will change to “01 STRT” indicating “start melody #1” for the remote start ON melody 3) Press the “TRUNK“ button or the “START“ button to scroll through the melodies 4) Press the “P” button to switch to the remote start OFF melody selection 5) Press the TRUNK button or the “START“ button to scroll through the melodies 6) Wait 10 seconds or press the “P” button for 5 seconds to exit programming The controller will beep once POWER SAVE mODE This feature turns off the screen after 15 seconds of no activity to save battery life 1) Press the “P” button for 5 seconds to access features The controller beeps twice 2) Press the “P“ button 5 times to select “Power Save” (clock reads “PS ON”) 3) Press the “TRUNK“ button to change between “PS ON” or “PS OFF” 4) Wait 10 seconds or press the “P” button for 5 seconds to exit programming SELECTinG mELODy & ViBRATE mODES Whenever 2-way alerts are received from the system, the controller can alert you with a melody, vibration, or both By default, the controller is set for melody only Press the “P” and “TRunK“ buttons simultaneously for 1 second to change the setting. PARKinG TimER & REmOTE START TimER The controller has 2 convenient timer functions The PARKING TIMER tells you how long you’ve been parked in case you are at a parking meter or other parking areas with time restrictions The REMOTE START TIMER tells you how long your engine has been running in remote start mode PARKinG TimER: Press LOCK twice within 5 seconds When the controller receives both LOCK conirmations, it will start the timer. REmOTE START TimER: This turns on every time you remote start note: Pressing the “P” during either timer will switch to the clock. BuTTOn LOCK You can lock the buttons on the controller to prevent accidental button presses To lock the buttons, press “P” and “START“ simultaneously for 1 second Repeat this to unlock the buttons 13 Anti-Carjacking Protection The system is equipped with two separate Anti-Carjacking protection features (ignition, open door, or both) All are programmable, and must be turned on to operate Once activated, the user has 60 seconds to cancel the Anti-Carjacking protection process (described below) If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 seconds to alert the user that the system is about to enter into an alarm condition The Valet Switch may still be pressed once during this period to cancel the Anti-Carjacking process If the Anti-Carjacking process is not cancelled before the 60 second countdown expires, the system will enter an alarm condition, sounding the siren and lashing the parking lights 30 seconds after this occurs, or should the ignition be turned off in the meantime, the stater interrupt will engage Once the system enters the alarm condition, it will not respond to the transmitter, nor will the system reset automatically after 60 seconds, and it can only be disengaged by: Step 1 Turning the vehicle’s ignition off Step 2 Turning the ignition back on Step 3 Within 5 seconds, perform an Emergency Override using the Valet Switch If the SecureCode has been customized, the correct number of Valet Switch presses must be made The different types of Anti-Carjacking protection are: ignition Activated Anti-Carjacking activates every time the vehicle’s ignition is turned on The Valet Switch must be pressed within 60 seconds of activating to cancel Anti-Carjacking This is User Programmable Feature #12 Door Anti-Carjacking activates when a door is opened after the vehicle is started and the engine is running The Valet Switch must be pressed within 60 seconds after activation to cancel Anti-Carjacking This is User Programmable Feature #12 14 Programming Controllers/Transmitters Standard Programming: Using this method to program additional or replacement transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert (UTA) feature Before you begin, have all transmitters which are to operate the system at hand and make sure the correct vehicle proile (see page 12) is selected on the controller(s) Step 1 Then, turn the ignition “on” Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times The siren/horn will briely sound, conirming that the system is ready to learn a transmitter code. Step 3 Press the “lock” button on each transmitter one at a time The system will chirp the siren/horn once to conirm that each was learned. If a code is not received within 10 seconds of Step 2, the learning process will automatically exit If the Unauthorized Transmitter Alert feature is on, programming a transmitter to the system will activate the “UTA” warning and the extended Status Light indication For the next 48 hours, the siren/horn will sound a brief series of chirps every time the vehicle’s ignition key is turned on Special Programming procedure to turn on the uTA feature: Use this method to program transmitters or optional controllers, and to turn on the Unauthorized Transmitter Alert feature Follow the same steps as the Standard Programming, but on any transmitter/controller being programmed instead of pressing the “lock” button, press the “lock” and the “unlock” buttons together This action turns on the Unauthorized Transmitter Alert feature and at the same time programs the transmitter or controller to operate the system Once the Unauthorized Transmitter Alert feature is turned on, the warning will sound for 48 hours after any transmitter programming, including the programming session which was used to turn it on This feature can only be turned off again by sending the system back to Omega for a reset Programming Features Step 1 Turn the ignition key “ON”, then “OFF” Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user features (10 times to access installer features) ~ The siren/horn will sound and the status light will turn on Step 3 Within 10 seconds of step 2, press the valet switch the number of times corresponding with the desired feature’s number ~ The siren/horn will chirp, the status lights, and the parking lights will lash equal to the selected feature Step 4 Change the feature by pressing the transmitter button that corresponds with the desired setting The siren/horn will chirp to correspond with the chosen setting 15 user Programmable Features Feature #1 - Remote Start Run Time 10 minutes (press “lock” button to program) - DEFAuLT 5 minutes (press “unlock” button to program) 15 minutes (press “trunk” button to program) 20 minutes (press “start” to program) This sets the maximum amount of time that the remote start will keep the engine running if it is not shut down by other methods Feature #2 - Flashing Light Conirmations unlock: On, RS: On (press “lock” button to program) unlock: On, RS: Flash (press “unlock” button to program) unlock: Flash, RS: On (press “trunk” button to program) unlock: Flash, RS: Flash (press “start” button to program) - DEFAuLT This feature affects the parking light conirmations for system unlock & remote start functions With the above options, you can select any combination of: unlock: Flash - Flashes twice after unlock unlock: On - Flashes twice then stays on for 30 seconds after unlock RS: On - Stays on during remote start mode RS: Flash - Flashes once every 15 seconds during remote start mode Feature #3 - Conirmation Chirp Volume Low (softest) (press “lock” button to program) medium Low (press “unlock” button to program) medium high (press “trunk” button to program) - DEFAuLT high (loudest) (press “start” button to program) This feature allows the choice different chirp volume levels, and when programming it, each selection will be conirmed in the chosen volume making it easy to choose the most suitable setting Feature #4 - BROWn Wire Audible Output Pulsed horn Low (press “lock” button to program) Pulsed horn medium (press “unlock” button to program) Pulsed horn high (press “trunk” button to program) Steady Siren (press “start” button to program) - DEFAuLT This changes the BROWN wire’s audible output when the alarm is triggered Steady siren must be selected when using a siren (other horn outputs stay at the Medium setting) The horn honk options will affect all horn honk outputs used as well as change the BROWN wire’s function Feature #5 - ignition Controlled Lock/unlock Off (press “lock” button to program) - DEFAuLT Lock w/ ignition On (press “unlock” button to program) unlock w/ ignition Off (press “trunk” button to program) Lock And unlock w/ ignition (press “start” button to program) This feature controls the lock/unlock operations when the ignition key is turned on/off, Feature #6 - Open Door Bypass of ignition Locking On (press “lock” button to program) - DEFAuLT Off (press “unlock” button to program) This feature cancels the automatic locking or unlocking of the vehicle’s doors if one of the doors is open when the ignition switch is turned on or off 16 user Programmable Features (cont’d) Feature #7 - unlock w/ Trunk Release On (press “lock” button to program) - DEFAuLT Off (press “unlock” button to program) “2nd channel” is most commonly used for trunk release, in which case the alarm should also disarm. This feature, when on, conigures the system to unlock/disarm when the 2nd channel is activated Feature #8 - Remote Start Activation From The Remote Press “start” button 1 time (press “lock” button to program) Press “start” button 2 times (press “unlock” button to program) - DEFAuLT Press “start” button 3 times (press “trunk” button to program) Press “start” button 4 times (press start” button to program) This feature changes how the remote start feature is activated from the remote Feature #9 - Last Door Arming Off (press “lock” button to program) - DEFAuLT On w/o doors locking (press “unlock” button to program) On w/ doors locking (press “trunk” button to program) “Last Door Arming” has the system automatically arm itself every time you exit the vehicle (the complete operation is described on page 8) Feature #10 - Automatic Rearming Off (press “lock” button to program) - DEFAuLT On w/o doors locking (press “unlock” button to program) On w/ doors locking (press “trunk” button to program) Enhanced auto rearm (press “start” button to program) “Automatic Rearming”, described on page 9, rearms the alarm if accidentally disarmed Options are to have Automatic Rearming operate with or without also locking the doors when the system does rearm Enhanced auto rearm allows you to cancel the rearming sequence by pressing unlock a 2nd time after disarming Feature #11 - Conirmation Chirps Siren + horn (press “lock” button to program) Siren Only (press “unlock” button to program) - DEFAuLT On Demand (siren+horn) (press “trunk” button to program) Off (press “start” button to program) This feature selects whether the siren and/or horn give conirmation chirps Both outputs will always sound when the alarm system is triggered or in panic mode Feature #12 - Anti-Carjacking ignition Only (press “lock” button to program) Door Only (press “unlock” button to program) ignition + Door (press “trunk” button to program) Off (press “start” button to program) - DEFAuLT This selects between the 2 forms of anti-carjacking protection Details on using anticarjacking protection are described on page 14 17 user Programmable Features (cont’d) Feature #13 - SecureCode DEFAuLT - 1 Press SecureCode is a unique patented feature which allows you to select the number of Valet Switch presses in two stages, instead of “1 press”, which would be required in order to perform an Emergency Override If any of the three anti-carjacking features are utilized, a customized SecureCode would also be required to turn it off once it is fully activated SecureCode operation is described on page 10 To custom program a new SecureCode: Step 1 Access user feature #13 (follow the steps on page 15) Step 2 Within 10 seconds slowly press and release the transmitter’s “arm/lock” button the number of times equal to the desired SecureCode for stage 1, allow the system to respond to each transmitter button press with a siren chirp before pressing the button again. A few seconds after the inal button press, the system will chirp conirming the total number for stage 1. Step 3 Conigure stage 2 of the SecureCode by pressing and releasing the “disarm/ unlock” button the number of times desired for the stage 2 The system will conirm as it did for stage 1. Feature #14 - ignition Activated Override On (press “lock” button to program) Off (press “unlock” button to program) - DEFAuLT This feature allows an activated system to be overridden and disarmed by simply turning the ignition switch on within 10 seconds of the system’s activation After 10 seconds, the Emergency Override must be performed Feature #15 - Alarm Trigger Duration 30 Seconds (press “lock” button to program) - DEFAuLT 60 Seconds (press “unlock” button to program) 90 Seconds (press “trunk” button to program) 120 Seconds (press “start” button to program) This feature selects the period of time for which the system sounds the siren (and/or horn) and lashes the lights when triggered. Caution: Before lengthening the Alarm Duration you should always check and determine if there are any local antinoise or nuisance ordinances in your area. Feature #16 - Arming Delay 3 Seconds (press “lock” button to program) - DEFAuLT 15 Seconds (press “unlock” button to program) 30 Seconds (press “trunk” button to program) 45 Seconds (press “start” button to program) This selects how long the alarm waits to monitor trigger zones after arming Feature #17 - Open Door Warning upon Arming On (press “lock” button to program) Off (press “unlock” button to program) - DEFAuLT When this feature is turned on, if one of the vehicle’s doors is open at the time that the system is armed via the controller or transmitter, the siren will chirp 3 times and the parking lights will lash 3 times, instead of once. 18 installer Programmable Features This group of Installer Programmable Features are all accessed as a group in the second level of features’ programming These features have a direct affect upon the system’s operations related to the installation and vehicle type AnD ShOuLD OnLy BE ChAnGED By ThE inSTALLER!!! Feature #1 - Remote Start Activation From The WhiTE/BLuE Wire 1 pulse (press “lock” button to program) - DEFAuLT 2 pulses (press “unlock” button to program) 3 pulses (press “trunk” button to program) 4 pulses (press start” button to program) This feature changes how the remote start feature is activated from the (-) activation input wire Feature #2 - PinK/WhiTE (iGn #2) Wire Function ignition (press “lock” button to program) - DEFAuLT Accessory (press “unlock” button to program) Starter (press “trunk” button to program) This feature changes the operation of the unit’s large PINK/WHITE output wire This feature should only be programmed by the installer Feature #3 - Engine Detection method Tachless hi (press “lock” button to program) - DEFAuLT Tachless Lo (press “unlock” button to program) Tach Wire (press “trunk” button to program) Data Tach (press “start” button to program) Crank Only (press “lock” & “unlock” to program) This feature selects the method in which the remote start monitors the engine’s running condition in remote start mode “Tachless hi” sensitivity mode uses a preset crank time (see installer feature #7) and monitors the vehicle’s voltage level to determine if the engine is running This setting looks for a voltage increase of 03v after cranking “Tachless Lo” sensitivity mode operates like the “Tachless Hi” setting but looks for a voltage increase of 05v after cranking “Tach Wire” Before this setting is programmed, refer to the “Violet/White wire” section of the installation manual for proper wiring connection and the Tach Learn Procedure It will crank the engine for up to 3 seconds or until a tach signal is detected “Data Tach” mode operates just like the “Tach Wire” setting except it takes its reading from the D2D data port instead of using the Violet/White wire Before using, make sure this function is supported by the Databus Interface module “Crank Only” AKA “blind start” is similar to the “Tachless” settings however, it only makes one start attempt and does not monitor engine running conditions This is useful for many “push-tostart” vehicles Feature #4 - Gasoline Or Diesel Engine Gasoline (press “lock” button to program) - DEFAuLT Diesel 15 Sec. Delay (press “unlock” button to program) Diesel 20 Sec. Delay (press “trunk” button to program) Diesel 30 Sec. Delay (press “start” button to program) This feature changes the system’s timing of the ignition and starter output sequence for gas or diesel engines Gasoline: the starter output will occur 3 seconds after the ignitions turn on When in “Tachless” mode, the engine running status is determined 10 seconds after starting Diesel: the starter output will occur 15, 20, or 30 seconds after the ignitions turn on (allows for glow plug warming) When in “Tachless” mode, the engine running status will be determined 40 seconds after cranking 19 installer Programmable Features (cont’d) Feature #5 - Light Relay Function Dome Light Output (press “lock” button to program) - DEFAuLT Start (press “unlock” button to program) ignition Output (press “trunk” button to program) Accessory Output (press “start” button to program) Status (press “lock” & “unlock” button to program) The system has two built-in relays, which can be programmed to perform several different functions The primary function of this relay, is to operate the vehicle’s dome, or interior lighting as part of the system’s operations Optionally, if desired or needed, this relay can be programmed for the other functions listed above Feature #6 Blue Satellite Port, Blue Wire Function ignition (press “lock” button to program) Status / GWR (press “unlock” button to program) - DEFAuLT Defrost Pulse (press “trunk” button to program) Pulse After Engine Off (press “start” button to program) horn (press “lock” & “unlock” button to program) This determines the function of the Blue wire on the Blue satellite relay port The Status setting turns on briely before the Ignition output and stays on during remote start mode The other pulse settings give a 08 second pulse under the selected condition Defrost Pulse will send a pulse after start only when the cabin temperature is below freezing (32 degrees F / 0 degrees C) Feature #7 - Starter Cranking Time 0.75 Second (press “lock” button to program) - DEFAuLT 1.00 Second (press “unlock” button to program) 1.5 Seconds (press “trunk” button to program) 2.25 Seconds (press “start” button to program) This feature determines the crank time of the 1st start attempt when in “Tachless” mode If the engine doesn’t start on the irst attempt, it will retry up to 3 more times extending the crank time by an additional 02 second with each attempt Feature #8 - Door Lock/unlock Outputs 0.8 Second Outputs (press “lock” button to program) - DEFAuLT 3 Second Outputs (press “unlock” button to program) Double Pulse unlock Output (press “trunk” button to program) Total Closure Lock Output (press “start” button to program) This changes the system’s doorlocking outputs to suite different vehicle requirements The total closure setting provides a 28 second lock pulse (press LOCK or UNLOCK is during the pulse to stop it) and a 08 second unlock pulse Feature #9 Remote Start Lock Control Off (press “lock” button to program) - DEFAuLT Lock After Start (press “unlock” button to program) unlock before start (press “trunk” button to program) unlock Before RS & Lock After RS (press “start” button to program) This feature allows for OEM alarm/lock control in relation to remote start operations thus eliminating extra wiring for OEM alarm control 20 installer Programmable Features (cont’d) Feature #10 - Turbo Timer Off (press “lock” button to program) - DEFAuLT Run 1 minute (press “unlock” button to program) Run 2 minutes (press “trunk” button to program) Run 3 minutes (press “start” button to program) This feature, the operation of which is described on page 8, when turned on conigures the system to automatically keep the engine running briely after the key is turned off. This operation is designed speciically for vehicles with turbocharged engines. nOTE: This feature is dependent on the proper wiring of the neutral safety circuit. Feature #11 - manual Transmission mode On (press “lock” button to program) Off (press “unlock” button to program) - DEFAuLT This feature changes the parameters of the system’s remote start operation to be suitable for manual transmission-equipped vehicles via a “setup” procedure which must be followed upon exiting the vehicle to ensure the transmission is in neutral Feature #12 Data Port Protocol Green: DBi, Black: DBi (press “lock” button to program) - DEFAuLT Green: iData, Black: iData (press “unlock” button to program) Green: DBi, Black: iData (press “trunk” button to program) Green: iData, Black: DBi (press “start” button to program) This feature determines which data protocol is used on each data port Choose this based on the accessory being connected to the port nOTE: When a BLADE is inserted, this feature automatically switches to the ADS protocol. Feature #13 - Alarm Functions On (press “lock” button to program) - DEFAuLT Off (press “unlock” button to program) This feature converts the system into a strictly Keyless Entry/Remote Start System by eliminating all antitheft alarm-oriented operations and features Feature #14 - Pulse ignition On Disarm On (press “lock” button to program) Off (press “unlock” button to program) - DEFAuLT This feature will pulse the ignition and activate any attached immobilizer bypass module for vehicles that require the ignition to be turned on to disarm the OEM alarm Feature #15 Lock On Prewarn On (press “lock” button to program) - DEFAuLT Off (press “unlock” button to program) This feature will automatically lock the doors to combat unauthorized entry from lock picking when the prewarn zone is triggered Feature #16 - Starter interrupt Functions Alarm Only (press “lock” button to program) Anti-Grind Only (press “unlock” button to program) Alarm & Anti-Grind (press “trunk” button to program) - DEFAuLT Automatic (press “start” button to program) Alarm Only - The Starter Interrupt is operable whenever the alarm is armed Anti-Grind Only - The Starter Interrupt is operable whenever remote start is on Alarm & Anti-Grind - This setting engages starter interrupt when the alarm is armed AND when the system is in remote start mode This prevents the starter from grinding if the user accidentally turns the key to “START” during remote start Automatic - This will cause the Starter Interrupt output to automatically engage 90 seconds after the ignition switch is turned “off”, and after disarming the system 21 installer Programmable Features (cont’d) Feature #17 Low Temp Crank Extender 0ms (Off) (press “lock” button to program) 200ms (press “unlock” button to program) - DEFAuLT 300ms (press “trunk” button to program) 400ms (press “start” button to program) When the vehicle’s interior temperature is below freezing, this feature adds extra crank time to the base timing (see installer feature #7) It applies to tachless modes only (installer feature #3) Feature #18 - Arm, Disarm or Additional Channels Arm / Disarm (press “lock” button to program) - DEFAuLT Arm / Channel 5 (press “unlock” button to program) Channel 4 / Disarm (press “trunk” button to program) Channel 4 / Channel 5 (press “start” button to program) The system has outputs designed for arming and/or disarming a factory-equipped security system These wires may be used instead to provide further system outputs, which are remotely operated by the controller or transmitter These outputs are in addition to the 2nd channel and 3rd channel outputs As shown in the programming assignment, the arm, disarm, channel 4 and channel 5 are programmable as various combinations For example, if the disarm output is needed, but not the arm output, then channel 4 may be made available for use Feature #19 - horn Relay Functions horn Output (press “lock” button to program) - DEFAuLT ignition (press “unlock” button to program) Trunk Release (press “trunk” button to program) Pulse After Start (press “start” button to program) The primary function of this second relay, is to operate the vehicle’s existing horn; either in conjunction with the electronic siren, or in place of the siren Using both the siren and the horn creates an extremely effective security system Optionally, if desired or needed, this relay can be programmed for the other functions listed above Feature #20 Low Current / motorcycle mode On (press “lock” button to program) Off (press “unlock” button to program) - DEFAuLT This feature, when on, reduces the system’s current draw by as much as 40% to maximize the vehicle’s battery life while the alarm is armed It causes the starter interrupt output to only operate when the ignition is turned on and reduces the frequency of the “armed” lashing status light signiicantly. This is ideal when the system is to be used on vehicles that have limited battery capacity and/or may sit for extended periods without charging the battery This device complies with FCC Rules part 15 Operation is subject to the following two conditions, (1) This device may not cause harmful interference and, (2) This device must accept any interference that may be received, including interference that may cause undesired operation The manufacturer is not responsible for any radio or TV interference caused by unauthorized modiications to this equipment. Such modiications could void the user’s authority to operate the equipment 22 SECuRiTy COnVEniEnCE User Feature Programming: Ignition on, off, press valet 5 times # Feature Lock Button (Brake x 1) Unlock button (Brake x 2) Trunk button (Brake x 3) Start button (Brake x 4) 1 Remote Start Run Time 10 min 5 min 15 min 20 min 2 Flashing Light Conirmations Unlock: ON RS: ON Unlock: ON RS: Flash Unlock: Flash RS: ON Unlock: Flash RS: Flash 3 Conirmation Chirp Volume Low Med-Low Med-High High 4 BROWN Wire: Siren / Pulsed Horn Pulse LOW Pulse MED Pulse HI Steady Siren 5 Ignition Lock / Unlock Off Ign On = Lock Ign. Off = Unlock Lock + Unlock 6 Door Open Bypass for Feat. #5 On Off 7 Unlock w/ Trunk Release On Off 8 RS Activation (Remote) Start x 1 Start x 2 Start x 3 Start x 4 9 Last Door Arming Off On w/o Lock On w/ Lock 10 Automatic Rearming Off On w/o Lock On w/ Lock Enhanced 11 Conirmation Chirps Siren + Horn Siren Only On Demand Off 12 Anti-Carjacking Ignition Door Ignition + Door Off 13 Secure Code Read Page 18 For Programming Instructions 14 Ignition Override On Off 15 Alarm Trigger Duration 30 sec 60 sec 90 sec 120 sec 16 Arming Delay 3 sec 15 sec 30 sec 45 sec 17 Open Door Warning Upon Arming On Off 4 pulses Lock + Unlock (Brake x 5) inSTALLER OnLy Installer Feature Programming: Ignition on, off, press valet 10 times 1 RS Activation (WHITE/BLUE wire) 1 Pulse 2 pulses 3 pulses 2 PINK/WHITE Wire Ignition Accessory Starter 3 Engine Detection Tachless Hi Tachless Lo Tach Wire Data-tach 4 Gasoline or Diesel Engine Gasoline 15 sec Diesel 20 sec Diesel 30 sec Diesel 5 Light Relay Function Dome Light Start Ignition Accessory Status Pulse After Engine Off Horn 6 Blue Sat Port BLUE Wire Ignition Status Pulse After Start below freezing 7 Crank Time 0.75 sec 1 sec 1.5 sec 2.25 sec 8 Door Lock/Unlock Outputs 0.8 sec 3 sec Double Unlock Total Closure 9 Remote Start Lock Control Off Lock after Start Unlock before Start Lock + Unlock 10 Turbo Timer Off 1 min 2 min 3 min 11 Manual Transmission On Off 12 Data Port Protocol Green: DBI Black: DBI Green: iData Black: iData Green: DBI Black: iData Green: iData Black: DBI 13 Alarm Functions On Off 14 Pulse Ign. on Disarm On Off 15 Lock On Prewarn On Off 16 Starter Interrupt Alarm Only Anti-grind Only Alarm/Anti-Grind Automatic 17 Low Temp Crank Extender 0 ms 200 ms 300 ms 400 ms 18 Arm/Disarm or CH. 4/5 Arm/Disarm Arm/CH. 5 CH. 4/Disarm CH. 4/CH.5 19 Horn Relay Function Horn Ignition Trunk Release Pulse After Start 20 Low Current/Motorcycle Mode On Off Crank Only 23 Back Cover Color cover is in a separate ile. 24
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Instance ID : uuid:9c2a45f2-1693-4d8c-b066-3dac65de6a53 Document ID : adobe:docid:indd:a712ace7-c308-11e2-81f0-cce26e98435d Original Document ID : adobe:docid:indd:a712ace7-c308-11e2-81f0-cce26e98435d Rendition Class : proof:pdf Version ID : 1 Derived From Instance ID : 335651fa-4634-11e2-9a45-9691798027e0 Derived From Document ID : adobe:docid:indd:7a3278f3-c9f2-11e1-810e-a9af046bd2e3 History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:DFAD9E52AA06E4119649E56D8DB311FC, xmp.iid:E0AD9E52AA06E4119649E56D8DB311FC, xmp.iid:B104A7C3AE06E4119649E56D8DB311FC, xmp.iid:1975980AAF06E4119649E56D8DB311FC, xmp.iid:2C4AFB73B906E4119649E56D8DB311FC, xmp.iid:933D898AB906E4119649E56D8DB311FC, xmp.iid:6631AB8EB906E4119649E56D8DB311FC, xmp.iid:EB170E9AB906E4119649E56D8DB311FC, xmp.iid:4B160CBFB906E4119649E56D8DB311FC, xmp.iid:5C91EBFFCE06E4119649E56D8DB311FC, xmp.iid:F4307171D906E4119649E56D8DB311FC, xmp.iid:2D037485D906E4119649E56D8DB311FC, xmp.iid:8609F565DC06E4119649E56D8DB311FC History When : 2014:07:08 10:15:32-04:00, 2014:07:08 10:15:32-04:00, 2014:07:08 10:47:20-04:00, 2014:07:08 10:49:19-04:00, 2014:07:08 12:03:51-04:00, 2014:07:08 12:04:29-04:00, 2014:07:08 12:04:36-04:00, 2014:07:08 12:04:55-04:00, 2014:07:08 12:05:57-04:00, 2014:07:08 14:38:05-04:00, 2014:07:08 15:52:50-04:00, 2014:07:08 15:53:24-04:00, 2014:07:08 16:14-04:00 History Software Agent : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Create Date : 2014:07:08 16:18:32-04:00 Modify Date : 2014:08:04 16:05:38+08:00 Metadata Date : 2014:08:04 16:05:38+08:00 Creator Tool : Adobe InDesign CS5.5 (7.5.3) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 6424 bytes, use -b option to extract), (Binary data 7497 bytes, use -b option to extract) Doc Change Count : 1119 Format : application/pdf Title : AL-1860-EDPB operation guide.indd Producer : Adobe PDF Library 9.9 Trapped : False GTS PDFX Version : PDF/X-1:2001 GTS PDFX Conformance : PDF/X-1a:2001 PXC Viewer Info : PDF-XChange Viewer;2.5.200.0;Dec 14 2011;19:51:40;D:20140722121236+08'00' Page Count : 24 Creator : Adobe InDesign CS5.5 (7.5.3)EXIF Metadata provided by EXIF.tools