Nutone Range Hoods Rl6100 H Users Manual
Nutone-Rl6330Wh-Quick-Start-Guide nutone-rl6330wh-quick-start-guide
Nutone-Rl6224Ss-Quick-Start-Guide nutone-rl6224ss-quick-start-guide
RANGE HOODS RL6300-H RL6200-install
RL6100-H to the manual 47392893-70a1-4fc2-93c7-db2a4851b675
2015-02-03
: Nutone Nutone-Range-Hoods-Rl6100-H-Users-Manual-466875 nutone-range-hoods-rl6100-h-users-manual-466875 nutone pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
READ & SAVE THESE INSTRUCTIONS! INSTALLATION INSTRUCTIONS Range Hoods RL-H SERIES (RL6100-H, RL6200-H, RL6300-H) IMPORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS WARNING — TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: • Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. • Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. CAUTION: To reduce the risk of fire or electric shock, do not use this range hood with an additional speed control device. WARNING — TO REDUCE THE RISK OF RANGE TOP GREASE FIRE: • Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. • Always turn hood ON when cooking at high heat or when cooking flaming foods. • Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. • Use proper pan size. Always use cookware appropriate for the size of the surface element. WARNING — TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: • SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. • NEVER PICK UP A FLAMING PAN — you may be burned. • DO NOT USE WATER, including wet dishcloths or towels — a violent steam explosion will result. • Use an extinguisher ONLY if: 1. You know you have a Class ABC extinguisher, and you already know how to operate it. 2. The fire is small and contained in the area where it started. 3. The fire department is being called. 4. You can fight the fire with your back to an exit. *Based on “Kitchen Fire Safety Tips” published by NFPA. WARNING — TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: • Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards - including fire-rated construction. • Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local code authorities. • When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. • Ducted fans must always be vented to the outdoors. WARNING: “To reduce the risk of fire, use only metal ductwork”. CAUTION: To reduce the risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages. ROOF CAP ADJUSTABLE ELBOW (if needed) ROOF PLANNING • Recommended mounting height is 24” to 30” above the cooking surface. • The hood should be mounted to the bottom of a standard wall cabinet. If the hood must be mounted directly to a wall, secure the hood to wall studs. • All wiring must be properly grounded. Connection should be made to a 110-120VAC lighting circuit (15 Amp) in the circuit breaker or fuse box. • DUCTING: (a) RL6300-H installs with 7” round duct vented vertically. RL5300-H installs with 5” round vented vertically. RL6100-H installs with 3¼” x 10” duct vented vertically or horizontally. (b) Make the duct run as short as possible. Try to avoid the use of elbows in the duct. All joints should be properly sealed. Do not use duct smaller than the discharge on the hood. (c) Do not terminate duct in an attic space. Run duct to the outside, using a roof or wall cap to terminate the run. 5” ROUND RL5300-H SERIES VERTICAL OR HORIZONTAL DISCHARGE USING 5” DUCT 5” ROUND DUCT RANGE HOOD FIGURE 1 RL6100-H SERIES VERTICAL OR HORIZONTAL DISCHARGE USING 3¼” X 10” DUCT 3¼” X 10” FIGURE 2 RL6300-H SERIES VERTICAL OR HORIZONTAL DISCHARGE USING 7” DUCT 7” ROUND FIGURE 3 PREPARATION 1. Use the dimensional drawing to lay out the Range Hood’s mounting holes, wiring access and ductwork. 2. Make cutouts for wiring and ductwork. 3. If the hood is to be ducted, install the ductwork so that is flush to the Range Hood’s mounting surface. • Refer to Figure 1 for Model RL5300-H. • Refer to Figure 2 for Model RL6100-H. • Refer to Figure 3 for Model RL6300-H. 4. Run two-conductor wire (with ground) from a power source to the hood location. Bring approximately 12” of wiring through wiring hole in cabinet. 5. Drill four 3/32” diameter pilot holes at points where mounting holes are marked in the filler strips or cabinet bottom. 6. Insert four (4) mounting screws (not supplied), leaving approximately ¼” of thread exposed. Use No. 8 or No. 10 round head screws. INSTALLATION 1. For RL6100 model, attach duct transition to top or back of hood using screws provided. (Refer to figure 4) Note: for horizontal venting the damper in the duct transition may be removed to avoid interference with the wall cap. 2. Remove top or back wiring knockout from the hood and feed the wiring into electrical box. 3. Align hood’s keyhole mounting slots over the four partially installed screws. 4. Making sure the duct positions over the hood’s duct transition, push the hood against the rear wall. Secure hood by tightening screws. 5. Using a long blade screwdriver, reach into the discharge openings and be certain the damper operates freely. 6. Secure ducting to hood. WIRING CONNECTIONS All wiring connections must comply with local codes and the unit must be properly grounded. 1. Make sure box connector is secure. 2. Refer to Figure 5. Make wiring connections. 3. Replace electrical box cover and secure with screw. COMPLETING ASSEMBLY 1. Install 75-watt (maximum) bulb in to receptacle. (Purchase bulb locally). 2. Install filter and light lens. REPLACEMENT PARTS Should replacement parts be required, please indicate hood model number and appropriate part number. Contact your NuTone dealer or write to NuTone: Madison and Red Bank Roads, Cincinnati, Ohio 45227-1599. Attn.: Parts Department. OPERATION AND MAINTENANCE NOTE: To avoid risk of fire, electrical shock, or injury, turn off power at supply before servicing. FILTERS The aluminum filter should be removed once a week and washed in hot detergent water. Rinse in clear, warm water and shake off excess moisture before replacing. The filter may also be cleaned in your dishwasher. CLEANING The hood should be wiped off occasionally both inside and outside using warm water, mild dish detergent and a soft cloth. Never use scouring powders, steel wool pads or any other abrasive cleaners which will destroy the hood’s finish. REPLACEMENT FILTERS PRODUCT MODEL FILTER USE Nutone Alternate 1 Alternate 2 RL6100-H K7589 BP29 97006931 RL6200-H K7588 41F 97007696 RL6300-H K7589 BP29 97006931 Product specifications subject to change without notice. Madison & Red Bank Roads, Cincinnati, Ohio 45227-1599 Printed in U.S.A., Rev. 4/99, Part No. K7591B
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Modify, Annotate, Fill forms, Extract, Assemble, Print high-res Create Date : 2003:06:12 21:14:27-05:00 Modify Date : 2003:06:12 21:14:27-05:00 Page Count : 4 Creation Date : 2003:06:13 02:14:27Z Mod Date : 2003:06:13 02:14:27Z Producer : Acrobat Distiller 5.0 (Windows) Author : PRINTSHOP Metadata Date : 2003:06:13 02:14:27Z Creator : PRINTSHOP Title : Untitled-1EXIF Metadata provided by EXIF.tools