Nyce Sensors Z30411 MOTION SENSOR WITH ZIGBEE RADIO User Manual NCZ 3041 manual

Nyce Sensors Inc. MOTION SENSOR WITH ZIGBEE RADIO NCZ 3041 manual

Users Manual

NCZ-3041 MOTION SENSOR User Guide Product Summary: Nyce Control’s NCZ-3041 is a wireless motion sensor using the ZigBee radio protocol. It is used in conjunction with a low RF transmit power wireless ZigBee network to monitor the occupancy state of indoor areas, and provide this information to other devices operating in a ZigBee Home Automation network. • Button functions: Identify/join Network • Accurate battery voltage level measurement and reporting back to co-ordinator • Network operation based on the ZigBee open profile Home Automation • Up to 4 years projected battery life Specifications: Detection Range 5m Horizontal Detection Range +/- 47° Vertical Detection Range +/- 41°
Installation Guidelines: • If using double sided tape for mounting sensor, thoroughly clean the surface to ensure proper adhesion because dust and particles can reduce the adhesion of the tape • Open the case and insert the battery, noting the correct polarity. Close the cover. • Place the NCZ-3041 indoors and away from sources of water/moisture and extreme weather conditions • Press the button once to join the network • Snap in front cover to mounted rear cover. Placement Guidelines: Place the motions sensor facing where you want to detect motion. Measurements below are approximate. 100° Top View Bottom View 41° 6’ 2.9’ 15’
Troubleshooting: To improve communication: • Reposition the sensor • Relocate the sensor • Move a ZigBee router / range extender closer to the sensor • If necessary, replace the sensor Technical Specifications: • Model Number: NCZ-3041 • Battery Type: 3.0 V CR2 850 mAhr Lithium • RF Frequency: ZigBee channels 11-26, 2.48 GHz • Operating Temperature: -10oC to 50oC (14oF to 122oF) • Dimensions: 20mm x 29mm x 65mm Battery Replacement: • Remove front cover to expose battery • Replace with 3.0 volt CR2 850 mAhr Lithium, noting the correct polarity of the battery Button Functionality: Action ZED State Description Not joined to any network Attempt to join the a Home Automation profile network (Open Standard) Joined to the network Identify to the network Press and release once Identifying to the network Stop Identifying, form Group. Press and release two times Any state LED flashes indicate whether ZED is joined to a network or not. Press and release four times Not joined to any network Attempt to join a Control 4 network Press and release six times Joined to a Control 4 or Open Standard network Leave the network Press and release ten times Any state Reset to factory settings. Press and hold for 4 seconds Joined to a Control 4 network Leave Control 4 network
LED Indicators: Colour Behaviour Description Flash 2 times Failed to join a network, or forced to leave, or not joined when queried (2 button presses) Flash once Initial detection of Occupancy or Motion Red Flash 3 times Provisioning failed Flash 2 times Successfully joined a Home Automation Network, or is currently joined Flash 3 times Provisioning succeeded Green Flash 5 times Successfully reset to factory defaults Flash 2-5 Hz Identify mode Flash 1 time Unsupported button command Orange Flash 5 times Communication or device error
MODEL #: NCZ-3041 FCC ID: Y8R-Z30411 IC ID: 9488A-Z30411 Compliance Statements: For complete declarations and certifications please visit: www.nycecontrol.com/compliance Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: the manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. Changes or modifications not expressly approved by NYCE Control, Inc can void the user’s authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is Subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Warranty: For product warranty information please visit: www.nycecontrol.com Support: For product support please email: support@nycecontrol.com

Navigation menu