Nyce Sensors Z32011 KEY FOB WITH ZIGBEE RADIO User Manual DOOR WINDOW SENSOR

Nyce Sensors Inc. KEY FOB WITH ZIGBEE RADIO DOOR WINDOW SENSOR

User Manual

NCZ-3201 KEY FOB User Guide Product Summary: Nyce Control’s NCZ-3201 is a wireless key fob using the ZigBee radio protocol. It is used in conjunction with a low RF transmit power wireless ZigBee network for access control to other devices operating in a ZigBee Home Automation network. • Button functions: network commands, state change commands for other devices • Accurate battery voltage level measurement and reporting back to co-ordinator • Network operation based on the ZigBee open profile Home Automation • Up to 4 years projected battery life
Troubleshooting: To improve communication:  Operate the device closer to the router / director  Move a ZigBee router / range extender closer to the desired operating area  Replace battery Technical Specifications:  Model Number: NCZ-3201  Battery Type: 3.0 V CR2032 Lithium coin cell  RF Frequency: ZigBee channels 11-26, 2.405 - 2.48 GHz  Operating Temperature: -10oC to 50oC (14oF to 122oF)  Dimensions: 32mm x 56mm x 6mm Battery Replacement:  Remove back cover to expose battery  Replace with 3.0 volt CR2032 Lithium coin cell battery, noting the correct polarity of the battery Button Functionality (Generic Commands): Button Function Lock Button Unlock Button Star Button 1 Tap ACE: Arm all zones (Endpoint 1) ACE: Disarm (Endpoint 1) ACE: Panic (Endpoint 1) 2 Taps ACE: Arm all zones (Endpoint 2) ACE: Disarm (Endpoint 2) ACE: Panic (Endpoint 2) 3 Taps ACE: Arm all zones (Endpoint 3) ACE: Disarm (Endpoint 3) ACE: Panic (Endpoint 3) Press ACE: Arm all zones (Endpoint 4) ACE: Disarm (Endpoint 4) ACE: Panic (Endpoint 4) Release ACE: Arm all zones (Endpoint 5) ACE: Disarm (Endpoint 5) ACE: Panic (Endpoint 5)
Button Functionality (Network Commands): Action Mode Action Press button 1 and button 2 together, then button 1 once Un-associated to any network Network Join to Open Std network Press button 1 and button 2 together, then Button 1 four times Un-associated to any network Network Join to C4 Network Press button 1 and button 2 together, then Button 1 six times Associated to the network Leave network Press button 1 and button 2 together, then Button 1, 10 times Associated to the network Restore defaults, leave network Press button 1 and button 2 together, then Button 1, 10 times Un-associated to any network Restore defaults Press button 1 and button 2 together, then Button 1 two times any Indicate network connectivity Press other than 1,2,4,6 10 times or other button combination any Single orange LED flash – unsupported command. The next press of multiple presses must occur within 1 seconds of the end of the last button press. Any button held down for more than 1 second will cause the keyfob to disregard the button press. Press-hold functionality will not be supported – only multi-press.
LED Indicators: LED Response Definition One green flash Message acknowledged by Coordinator, or button pressed (command mode) Two green flash Network join succeeded, or status = joined One red flash button pressed (network mode) 2 red flashes Network leave or status = not joined 3 slow Red flashes, 1 second after other LED signalling is complete Low battery One Orange flashes Unsupported button command Two Orange Flashes Network Error Five Green flash Successfully reset to factory defaults All flashes are 250ms in duration. Repeated flashes are each followed by a 250ms pause, unless otherwise indicated. A “slow” flash is 250ms in duration followed by a 1sec pause.
MODEL #: NCZ-3201 FCC ID: Y8R-Z32011 IC ID: 9488A-Z32011 Compliance Statements: For complete declarations and certifications please visit: www.nycecontrol.com/compliance Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: the manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. Changes or modifications not expressly approved by NYCE Control, Inc can void the user’s authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is Subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Warranty: For product warranty information please visit: www.nycecontrol.com Support: For product support please email: support@nycecontrol.com

Navigation menu