OKIN Refined Electric Technology JLDK-18-1 Wireless remote handset User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1980473
Application ID	+wMDfqP1j540BlmJm+XX0Q==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.36kB (229468 bits)
Date Submitted	2013-06-02 00:00:00
Date Available	2013-06-02 00:00:00
Creation Date	2013-05-31 13:27:09
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2013-05-31 13:27:09
Document Title	Microsoft Word - Operating manual of the remote control.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

OKIN Refined Electric Technology Co., Ltd
Operating Manual of Remote Hand Control
1、Interface of the Handset
2、Button description
A.
button: Press the button, the head and foot motor will move simultaneously and
do not stop until return to the position of the system set (reading position). You can press
any button to stop action during moving.
B.
button: Press the button, the head and foot motor will move simultaneously and
do not stop until return to the position of the system set (recline position). You can press
any button to stop action during moving.
C.
button: Press the button, the head and foot motor will move simultaneously and
do not stop until return to the position of the system set (zero gravity position). You can
press any button to stop action during moving.
The reading, recline and zero gravity position can be changed by the end user.
Step 1: Adjust the head position and feet position to a desired position;
Step 2: Press and hold the
Step 3: Release
button for 3sec, backlight LED start flashing;
button, during next 1sec, press
or
or
button, LED stop flashing. Then the corresponding position is updated successfully.
Page 1 of 5
OKIN Refined Electric Technology Co.,Ltd
D.
HEAD button：Press and hold the button, the head motor will go up or down.
E.
FEET button：Press and hold the button, the foot motor will go up or down.
FLAT button：Press the button, the head and foot motor will move down to the flat
F.
position simultaneously. You can press any button to stop action during moving.
G.
H.
HEAD Massage ON/OFF button：
Press the button to turn on or turn off the vibrating of the head vibrator;
FEET Massage ON/OFF button：
Press the button to turn on or turn off the vibrating of the feet vibrator;
I.
HEAD and FEET Massage intensity button：
Press the button to change circularly the vibrating intensity of the head and feet
vibrator by one level, total 3 levels;
J.
Massage time button：
Press the button and released to stop all moves and change circularly the vibrating
time of the head and feet vibrator by one level, total 4 levels;
The indication of the vibrating time is below:
The yellow LED on-------10minutes
Page 2 of 5
OKIN Refined Electric Technology Co.,Ltd
The blue LED on-------20minutes
Both of the yellow LED and the blue LED on-------30minutes
Both of the yellow LED and the blue LED off-------forever
3、Wireless Matching operation
Step 1: Set up DIP switch to a desired channel;
The below is only for example.
Step 2: Disconnect the DC plug (not the AC plug) of the control box from the SMPS to turn off
the power;
AC plug
DC plug
SMPS
control box
Page 3 of 5
OKIN Refined Electric Technology Co.,Ltd
Step 3: Two seconds later connect again the DC plug of the control box to the SMPS to turn on
the power.
Step 4: Press simultaneously and hold the head up button
and feet up button
on the
handset until backlight LED flashing. Release the two buttons and LEDs continue flashing and
search with control box, once the LEDs stop flashing the matching is successful, which means
the control box and the handset can work together.
All matching set up process must finish in two minutes after turning on again the power of the
control box.
Configuring two beds to a big bed
Connect the two control boxes with the cable as below, as do this, the two beds can work
synchronously.
Usage notice of the Control Box
1. The control box is designed for using the SMPS of 29VDC/ around 2A as the power. It is
necessary to use the SMPS provided by us when normal operation.
2. In the case of the AC power utility failure, the battery box for backup of 18VDC can be used
as the power. It is only for flatting the bed plate without load if the battery box used as the
power and each one of the batteries must be new with 9V voltage. Due to the electric
quantity of the batteries limit it is impossible to move repeatedly the bed plate, it is strongly
recommended to use in turn the button “Head Down” and “Feet Down” to drive the head
motor and feet motor in turn not simultaneously to flat the bed plate. Not to use the button
“Flat” to flat the bed plate, in this way the battery voltage will be pulled down by the bigger
current because the head motor and the feet motor is driven simultaneously, that perhaps
results the motors will not work normally. It isn’t also strongly recommended to start the
massage motors when the battery box used as power.
FCC STATEMENT: FCC ID: PCU-JLDK-18-1
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Page 4 of 5
OKIN Refined Electric Technology Co.,Ltd
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Page 5 of 5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2013:05:31 13:27:09+08:00
Modify Date                     : 2013:05:31 13:27:09+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : Microsoft Word - Operating manual of the remote control.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:e955b5e7-3797-493a-90ce-008b7f76b966
Instance ID                     : uuid:524bf8ad-c2d0-4e03-a002-09d3e47d5c25
Page Count                      : 5

EXIF Metadata provided by EXIF.tools