OKIN Refined Electric Technology JLDK-21-01 Shenzhou Spaceship2012 Wireless remote handset User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2070745
Application ID	B/vb/fjJOYXzy3i5Wzs/SQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.96kB (374476 bits)
Date Submitted	2013-09-13 00:00:00
Date Available	2013-09-13 00:00:00
Creation Date	2013-08-14 08:51:32
Producing Software	Microsoft® Word 2010
Document Lastmod	2013-09-11 16:20:58
Document Title	User manual
Document Creator	Microsoft® Word 2010
Document Author:	Wayne Cao

OKIN Refined Electric Technology Co., Ltd
Operating Manual of Remote Hand Control
1、 Interface of the Handset
S1 S2
S3
2、 Button description
A．Press button(S1) and hold until you bring the chair to a seated position. If you
release the button, the motor will immediately shut off.
B．Press button(S2) and hold until you bring the chair to a reclined position. If you
release the button, the motor will immediately shut off.
C．Double press button(S3) and the Remote handset will enter a connecting state
for 30s. During this time, If a nearby Control box is also in connecting state, they
will be connected with each other.
3、 indicator light description
A. Only orange light flashing indicates that the motor is running to a seated
position normally.
B. Only blue light flashing mostly indicates that the motor is running to a reclined
OKIN Refined Electric Technology Co., Ltd
position normally. Sometimes, it indicates the Remote handset being in a
connecting state.
C. Both of the indicator lights flashing 3 times indicates something wrong
happened to the Remote handset during operation, as follows:
a. In connecting state, the Remote handset fail to connect to a Control box.
b. In connected state, if you press button(S1 or S2), the control commands cannot
reach the Control box.
4、 To connect the Remote handset to a Control box
Step1:
Connect the DC plug of the Actuator to the SMPS to turn on the power. Connect
the 5-pin plug of the Control box to the Actuator.
DC plug
5-pin plug
SMPS
AC plug
Control box
Step2:
Double press the button of the Control box. The light going on indicates the
Control box entered a connecting mode for 30s.
Step3:
Double press button(S3) and the blue light flashing indicates the Remote handset
being in a connecting mode.
Step4:
When flashing blue light goes out, the Remote handset and the Control box are
connected. If blue light flashing state turns to double indicator lights flashing 3
times, it means the Remote handset fails to connect to the Control box. At this
OKIN Refined Electric Technology Co., Ltd
time, you should repeat step2 ~ step4.
FCC STATEMENT:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Wayne Cao
Create Date                     : 2013:08:14 08:51:32+08:00
Creator Tool                    : Microsoft® Word 2010
Modify Date                     : 2013:09:11 16:20:58+08:00
Metadata Date                   : 2013:09:11 16:20:58+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:b335bf60-c06d-4f68-9d71-24262251d712
Instance ID                     : uuid:a702a682-62b7-407c-a8f5-cf039f4aba45
Page Count                      : 3
Author                          : Wayne Cao

EXIF Metadata provided by EXIF.tools