OKIN Refined Electric Technology RF358D Remote Control User Manual Function Instructions of RF358D

Download:
Mirror Download [FCC.gov]
Document ID	4066926
Application ID	4bkXAQP+H7XRi99g62eLgQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.31kB (303867 bits)
Date Submitted	2018-11-09 00:00:00
Date Available	2018-11-09 00:00:00
Creation Date	2018-10-23 11:30:50
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2018-11-09 16:33:55
Document Title	Microsoft Word - Function Instructions of RF358D
Document Creator	PScript5.dll Version 5.2.2
Document Author:	baclsh51

Issuing Department：Bedding
Division
Function Test
Instructions
Function Test Instructions of RF358D
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 1 of 8
Function Instructions of RF358D
Product description
LED for MassageWave
MassageWave
FootMassage
HeadMassage
FAN Strength
FANSYNC
Fan Left
FAN Right
UnderbedLightadjustment
Foot actuator adjustment
Head actuator adjustment
Zero G
Anti snore
Memory Favorite
MemoryTV
Flat
Made by:Jarek
Checked by:
1 /8
Confirmed by:
Issuing Department：Bedding
Division
Function Test
Instructions
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 2 of 8
Function Test Instructions of RF358D
FCC ID: WKZ-CU3582
IC:20840-CU3582
Function
1.
description
Paring code
Process of paring code:
Double click RESET button on control box，pairing LED turns on，The control box enters the mode
of code paring;
Press and hold the code paring button under battery cover, the backlight of paring LED flashes,
and the backlight of remote flashes, the remote enters into mode of code paring;
The backlight of paring LED stops flashing and the paring LED of control box turns off, it indicates
that the code paring is successful;
If fails, repeat all the steps above;
2.
Head actuator moves out
Press and hold the head upbutton, head actuator moves out, stop when released;
Made by:Jarek
Checked by:
2 /8
Confirmed by:
Issuing Department：Bedding
Division
Function Test
Instructions
Function Test Instructions of RF358D
3.
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 3 of 8
Head actuator moves in
Press and hold the headdown button, head actuator moves in, stop when released;
4.
Foot actuator moves out
Press and hold foot up button, foot actuator moves out, stop when released;
5.
Foot actuator moves in
Press and hold foot downbutton, head actuator moves in, stop when released;
6.
Underbed lighting
Click underbed lighting button, turn on (or turn off) the undered lighting, it switches its status
once when click the button every time;
7.
FLAT function
Click FLAT button, head and foot actuators move to the lowest position(when the actuators are
free, you can stop the massage motor, turn off the massage motor LED), running can be stopped
by clicking any button;
8.
ZERO G position
Click ZERO G button, head and foot actuators move to the memory position which is preset,
running can be stopped by clicking any button;
9.
ANTISNOREposition
Click ANTISNORE button, head and foot actuator actuators move to the memory position which is
preset, running can be stopped by clicking any button;
Made by:Jarek
Checked by:
3/8
Confirmed by:
Issuing Department：Bedding
Division
Function Test
Instructions
Function Test Instructions of RF358D
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 4 of 8
10. Memory Favoriteposition
ClickMemory Favoritebutton, head and foot actuators move to the memory position which is
preset, running can be stopped by clicking any button;
11. Memory TVposition
ClickMemory TVbutton, head and foot actuators move the memory position which is preset,
runningcan be stopped by clicking any button;
12. Customized position button（ANTISNORE ，Memory Favorite，Memory
TV）
The custom setting processesare as follows:
1. Click FLATbutton, flat the actuator;
2.Operate the head uporhead down or foot up or foot down button, adjust
thehead actuator and foot actuator to an expected position;
3.Press and hold the button that needs customize position, hold for 5s, the LED
on the top of the remote cycle flashes;
4.Release the button, LED stops flashing, it indicates that the customization is
finished.
The default position setting can be restored to the default setting. Press and
hold the ZERO G + FLAT button for about 5 seconds. The LED on the top of the
remote cycle flashes, whenthe LED stops flashing, it indicates that the setting to
the default position is finished.
13. Head massage adjustment function
Every time when click “HEAD massage“ button, the intensity of head massage
motor enhances by one level, there are three massage intensities totally. When
in the third intensity, click “ HEAD massage“ button again, the intensity
levelswitches to 0, the mode cycles;
Made by:Jarek
Checked by:
4/8
Confirmed by:
Issuing Department：Bedding
Division
Function Test
Instructions
Function Test Instructions of RF358D
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 5 of 8
14. Foot massage adjustment function
Every time when click “FOOTmassage“ button, the intensity of head massage
motor enhances by one level, there are three massage intensities totally. When
in the third intensity, click “FOOT massage“ button again, the intensity level
switches to 0, the mode cycles;
Made by:Jarek
Checked by:
5/8
Confirmed by:
Issuing Department：Bedding
Division
Function Test
Instructions
Function Test Instructions of RF358D
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 6 of 8
16. Childlock
Press and hold Head Up & Head Down., after more than 6s, you can see the backlight flashes 2
rounds, which indicates that the remote turns on the child lock; if you press any button, the
control box has no action;
Press and hold Head Up & Head Down, after more than 6s, you can see the backlight flashes 2
rounds, which indicates that the remote turns off the child lock; if you press any button, the
control box has corresponding action;
17. Affiliated FAN function
This function is used as an accessory for the FAN control box. It is used by the sync cable access to
control box MFP port. The functions are as follows:
1.17.1. Click the FAN L+ button to turn on the port B of fan control box which controls the
low‐mid‐hign output of fan, and there are third air volume which corresponds to the
three indicators of FAN L led. The default fan is turned on for 10 hours. Click again to
close the port B of fan control box.
Press and hold the FAN L+ button for more than 3s to turn on the step‐down mode of the
left fan; click again to switch the fan gear and automatically turn off the step‐down
mode;
1.17.2. Click the FAN R+ button to turn on theport A of fan control box which controls the
low‐mid‐hign output of fan, and there are third air volume which corresponds to the
three indicators of FAN R led. The default fan is turned on for 10 hours. Click again to
close the port A of fan control box.
Press and hold the FAN R+ button for more than 3s to turn on the step‐down mode of
the right fan; click again to switch the fan gear and automatically turn off the step‐down
mode;
1.17.3. Click FAN SYNC button to turn on the port A &B of fan control box which controls the low
wind‐>mid wind‐>hign wind‐>off of fan, corresponds the three indicators on both sides
of the FAN L led and FAN R led, and the default fan is turned on for 10 hours, so that the
cycle is repeated;
Press and hold the FAN SYNC button for more than 3s, and turn on the step‐down mode
of the two fans at the same time; click again to switch the fan gear and automatically
close the step‐down mode;
2.19.4. Press and hold the FAN L+ and FAN R+ button simultaneously. If it exceeds 3S, you can see
that the backlight of the remote control flashes twice. The fan control box enters the demo mode.
The default time is 5min. Press any FAN related button to turn off the fan control.
Remark：
LED 1 lights, it corresponds low wind, output duty ratio is 30%;
LED 2 lights, it corresponds mid wind, output duty ratio is 40%;
Made by:Jarek
Checked by:
6/8
Confirmed by:
Issuing Department：Bedding
Division
Function Test
Instructions
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 7 of 8
Function Test Instructions of RF358D
LED 3 lights, it corresponds high wind, output duty ratio is 50%;
All three LEDs are off to indicate that the fan function is turned off;
Step‐down mode description：
In the current fan position, once the step‐down mode is started, after the fan runs for 5 hours, it
automatically switches to the corresponding weakened gear position. The corresponding
relationship is as follows:
Fan gear
Gear duty cycle in normal
mode
Step‐down mode, gear duty
cycle after 5 hours
30%
0%
40%
30%
50%
40%
18. Description of remote control current and backlight
After power on, observe the work current of remote(<40mA);
After the key operation, place still for 5s, the backlight of remote turns off and
the remote enters into sleep mode. Observe the sleep current of remote
control (< 10uA).
If the remote control enters into sleep mode, the remote can be wakened up
by pressing any button or shaking; Continues to wake it up for 6 times and do
not press any button, then you can only wake up the remote control by key
operation.
Note: When the actuator is in flat postion, and you press the memory
position button, the motor can move to the theoretical angle or
theoretical stroke, the error range will no more than 3 ° or 5mm.
Made by:Jarek
Checked by:
7/8
Confirmed by:
Issuing Department：Bedding
Division
Function Test
Instructions
Function Test Instructions of RF358D
Date：
2018-10-15
Author：
Aaron
Model：RF358D
Edition：
1.0
Page 8 of 8
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
ISED RSS Warning:
This
device
complies
with
Innovation,Science
and
Economic
Development
Canada
licence exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this devicemay not cause interference, and
(2) this device must accept any interference, includinginterference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,même si le brouillage
est susceptible d'en compromettre le fonctionnement.
Made by:Jarek
Checked by:
8/8
Confirmed by:

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : baclsh51
Create Date                     : 2018:10:23 11:30:50+08:00
Modify Date                     : 2018:11:09 16:33:55-08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:11:09 16:33:55-08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - Function Instructions of RF358D
Creator                         : baclsh51
Document ID                     : uuid:37fcd69c-d933-4521-b694-9f4cb3d6ae37
Instance ID                     : uuid:6c29d26e-4c98-406f-8346-47d4e5d56b3d
Page Count                      : 8

EXIF Metadata provided by EXIF.tools