OPISYS orporated AVHR-5000 Dual Band Repeater (Model: AVHR-5000) User Manual Microsoft PowerPoint manual

OPISYS Incorporated Dual Band Repeater (Model: AVHR-5000) Microsoft PowerPoint manual

Users Manual

Installation User GuideMODEL : AVHRMODEL : AVHR--50005000
Page 1- Content -1. General Information1.1 Precautions1.2 Features2. System Components3. Installation3.1 Outside Antenna Installation3.2 Inside Antenna Installation3.3 Amplifier and Antenna Connection3.4 Operating Instructions4. Trouble Shooting4.1 LED Alarm4.2 Insufficient Outside Signal Problem4.3 Vehicle Battery Discharge Problem5. Specification5.1 Amplifier Specification5.2 Outside Antenna Specification5.3 Inside Antenna Specification5.4 Cigarette Power Code Specification6. Certificates7. Memo
1. General Information1.1 Precautions 1.1.1 Do not drop the device - Drop could damage the product1.1.2 Do not place near magnetic- It could be cause of malfunction1.1.3 Product is supposed to be used with the cigarette power code. If you want to use fuse cable, please ask professional installers. 1.1.4 Please unplug either with cigarette power code or fuse cable if you don’t use- It may cause battery discharge1.1.5 Set up product on advised location- It may not properly operate on unadvised location1.1.6 Do not repair or remodel- It could be cause of malfunction. Please contact a store where you purchased if there is a problem1.1.7. Do not operate device while driving - It could be cause of traffic accident1.1.8 Turn off the ignition before set up the device.1.1.9 Do not put the device near vehicle air bag in the car- You could be hurt by burst air bag or air bag which doesn’t operate properly 1.1.10 Do not handle with wet hands- Avoid risk of an electric shock1.1.11 Clean up the surface where you set up inside and outside antenna- It could be cause of a traffic accident when the antennas detached from the surface. 1.1.12 Please stop use and unplug when smog comes out of the product or could detect strange odor Page 2Reference : Things you need to know to operate the product properly Caution : Things that you need to know not to damage the product Warning : Showing instructions for users to avoid unexpected hazard
1.2 Features1.2.1 SummaryThis product is installed on cars, trucks, trailers, boats and homes to improve user’s mobile phone signal. It is a RF type amplifier used for only CDMA Cellular bands in the 800MHz and PCS1900MHz .(Please see page 11 for Operating Frequency)1.2.2 FeaturesPage 3I. Decrease dropped callII. Increase 2G/3G/4G data speedIII. Battery life extensionIV. Voice quality improvement I. Strong coverage area- Gain 55dB II. Automatic Overload Protect & Detect System- Plug and play systemsIII. IS-95A Spurious Specifications with 25dBm(0.3W) Output power- Providing high data communication rate IV. Complete Repeater Kit.-Providing all components for installation V. Dual Band Amplifier - 800MHz / 1900MHz VI. LED Alarm System VII. GUI(Graphic User Interface)- Please ask professional installers about GUI program.VIII. Cost Effective Application for Vehicles, Boats, and Homes- For at home users need to purchase cables, inside and outside antennas to install.
Page 4① Inside Antenna ②AVHR-5000 ③User Manual④cigarette power code ⑤Outsider Antenna① . Inside Antenna: connects signal between mobile phone and amplifier②. AVHR-5000: amplifies signal from outside antenna which receives signal from a base station and sends amplified signal to mobile phone ③. User Manual: shows how to operate system ④. Cigarette Power Code : is the source of electricity⑤. Outside Antenna: connects signal between base station and amplifier ▣ System Components1.2.3 Installation2. System Components
Page 53. Installation3.1 Outside Antenna Installation3.1.1 Outside antenna is magnetic. So you can mount on the roof of vehicle3.1.2 Outside antenna should be distance at least 5 feet from inside antenna 3.1.3 As showing on the picture below, suggested place to mount outside antenna is rear end of roof3.2 Inside Antenna Installation3.2.1 Inside antenna is self adhesive. You can place it wherever you want3.2.2 Before installation, please remove attached paper3.2.2 Recommend to mount under location shown on the picture Better BestGood
Page 63.3 Amplifier and Antenna Connection3.3.1 Place the amplifier under the seat or appropriate location.3.4 Operating Instructions3.4.1 As the picture shown below, plug in the cigarette power code and press red button to turn on3.3.2 Connect inside antenna connector to repeater
Page 73.4.2 Connect DC Jack as picture down below3.4.3 Turn on the Switch as picture down below3.4.4 After turning on switch, green LED light will be on(Green LED means that system is normal mode) ※ Green and Red LED simultaneously brinks 3 times and then only green LED light will be on
Page 84. Trouble Shooing4.1 LED AlarmItem GREEN LED RED LED 문제점 찾기Setting/Resetting ON (after 3 times blinks) 3 times blinks See 4.1.1Normal Mode ON OFF See 4.1.2CellularOverload Blink( once) -See 4.1.3Oscillation Blink(twice) -See 4.1.4Insufficient Isolation Blink(3 times) -See 4.1.5Alarm Checking Blink(Consecutively) -See 4.1.6PCSOverload -Blink( once) See 4.1.3Oscillation -Blink(twice) See 4.1.4Insufficient Isolation -Blink(3 times) See 4.1.5Alarm Checking -Blink(Consecutively) See 4.1.54.1.1 ① Check if the LED light is on, on the cigarette power code② Verify that DC code is connected correctly4.1.2 ① Green LED light is normal mode. If it is blinking 2-3 times in a few seconds, please see 4.1.3 ~ 4.1.64.1.3 ① This is normal mode that checking on input power signal and shows signal status to users. ③ It will go back to normal mode soon4.1.4 ① There is an oscillation between inside and outside antenna.② This status is caused by a structure around that temporarily disturbs mobile signals. Please move your vehicle to other location. LED light will turn to green
Page 94.2 Insufficient Outside Signal Problem After repeater installed, if there is insufficient outside signal around your vehicle such as uncovered signal area, you may not use your mobile phone4.3 Vehicle Battery Discharge ProblemVerify cigarette power code LED light is on as shown below. If not, check either vehicle key is appropriately positioned or engine is on. In case of battery discharge, replace battery. 4.1.5 ① There is a insufficient isolation between inside and outside antenna② While installing if LED light blinks three times, move the inside and outside antenna away and turn on/off and move antenna as needed. ③ If there was no blinking problem while set up but happens after, it could be caused by surrounding structure but that could be come back to normal if you move to different location. 4.1.6 ① Repeater CPU software is checking out if there are any problems such as isolation, overload or conciliation. ② On alarm checking status repeater is not operating
Page 105. Specification5.1 Amplifier Specification Items Cellular PCS RemarksOperating FrequencyDownlink 869 ~ 894 MHz 1930 ~ 1990 MHz CDMA OnlyUplink 824 ~ 849 MHz 1850 ~ 1910 MHz CDMA OnlyGainDownlink 55dB±2.0dB 55dB±2.0dBUplink 55dB±2.0dB 55dB±2.0dBOutput Power LevelDownlink +10dBm +10dBm@ 1FAUplink +25dBm +25dBmRippleDownlink < 5dB < 7dBUplink < 5dB < 7dBNoise FigureDownlink < 5dB < 5dBUplink < 5dB < 5dBALC LevelDownlink +10dBm ±1dB +10dBm ±1dB@ 1FAUplink +25dBm ±1dB +25dBm ±1dBShutdown LevelDownlink +10dBm ±1dB +10dBm ±1dBAfter ALCUplink +25dBm ±1dB +25dBm ±1dBSpuriousDownlink&Uplink-45dBc/30kHz @±885KHz@PCS-50dBc/30kHz @±1.98MHz-45dBc/30kHz @±750KHz@Cellular-50dBc/30kHz @±1.98MHzVSWR < 1 : 1.8Propagation Delay < 1usFrequency Stability ≤ ±0.05ppmGUI Interface RS-232CIsolation Detection Range 45dB ~ 65dBOnly Uplink Shutdown ≥ -45dBm ±1dB @ downlink Input Signal For BTS Protection Input Voltage 6.0Vdc / 3.5A Cigar Charger ‘s VdcPower Consumption 6.0Vdc / 840mA @ No callRF Connector Type FME-male Operating Temperature -40°C ~ +50°C (-40°F ~ 122°F)Weight < 2.2 Ibs (< 1.0kg)Size(L*W*H) 4.9*4.8*1.4nch (125.5 * 123 * 35.5mm)
Page 115.2 Outside Antenna Specification5.3 Inside Antenna Specification5.4 Cigarette Power Code Specification 5.4.1 Input SpecificationItems Cellular PCS RemarksOperating Frequency 820 ~ 890 MHz 1710 ~ 1990 MHz -Bandwidth 70MHz 170MHz -Gain 5dBi -VSWR ≤ 2.0 : 1 -Impedance 50 Ω -Polarization Vertical -Connector FME(Female) -Antenna Length 28Cm -Weight 220g -Cable Length 5M -Items Cellular PCS RemarksOperating Frequency 820 ~ 890 MHz 1710 ~ 1990 MHz -Bandwidth 70MHz 170MHz -Gain 2dBi -VSWR ≤ 2.0 : 1 -Impedance 50 Ω -Polarization Vertical or Horizontal -Connector FME(Female) -Weight 50g -Cable Length 2M -Items Min Typical MaxNormal DC Input Voltage 12V -24VDC Input Voltage Range 12V -24VDC Input Voltage Current - - 3.0A
Page 125.4.2 Output SpecificationItems Min Typical MaxNormal DC Output Voltage -6.0Vdc -DC Output Voltage Range 5.7Vdc -6.3VdcLoad Current Range - - 3.5ARipple - - 350mVOver Current Protection 4.2 -7.0AShort Circuit Protection -Yes -6. Certificates6.1 FCC Certification▪ Model : AVHR-5000▪ Certificate Data : 2011.03 ▪ Certificate No.:6.2 IC Certification ▪ Model : AVHR-5000▪ Certificate Data : 2011.03 ▪ Certificate No.: 7. RequirementA minimum separation distance of 8 inchs(20 cm) must be maintained between the user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure requirements. For more information about RF exposure, visit the FCCwebsite at www.fcc.gor
Page 137. Memo

Navigation menu