OPTOELECTRONICS OPN2102I Data Collector User Manual
OPTOELECTRONICS Co., Ltd. Data Collector Users Manual
Users Manual
SPECIFIICATIONS MANUAL OPN OP N-221002i OPN-2102i 1st Data Colle ector with h Bluetootth This manual prov vides speciifications fo or the OPN N-2102i Bluuetooth data collector with laser ba arcode sca anner. 1st SPECIFICATIONS MANUAL OPN-2102i 1st The information in this document is subject to change without notice. Document History Model Number: Edition: Date: OPN-2102i 1st 30-September-2016 Specification Number: Original Spec Number: SS16056 (SS16017) © 2016 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers Please read this manual carefully before installing or using the product. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase excluding batteries. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your data collector or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184 SUPPORT USA Europe Phone: 800-636-0090 Email: support@opticonusa.com Web: www.opticonusa.com Phone: +31235692728 Email: support@opticon.com Web: www.opticon.com SPECIFICATIONS MANUAL OPN-2102i 1st Revision History Product Name : OPN-2102i Edition st Date 2016/09 /30 Page Section Description of Changes SPECIFICATIONS MANUAL OPN-2102i 1st Contents Abstract............................................................................................................................ 6 Overview .......................................................................................................................... 6 Basic Specifications ....................................................................................................... 7 Detailed View ................................................................................................................... 9 Electrical Specifications ............................................................................................... 10 5.1 USB ........................................................................................................................................ 10 5.2 Wireless Charging .................................................................................................................. 10 Interface Specifications ................................................................................................ 10 6.1 USB Interface ......................................................................................................................... 10 6.1.1 Connector ....................................................................................................................... 10 6.1.2 USB Interface Circuit ...................................................................................................... 10 6.2 Bluetooth ................................................................................................................................ 11 6.3 NFC Tag ................................................................................................................................. 11 Optical Specifications................................................................................................... 11 7.1 Basic Specifications ............................................................................................................... 11 7.2 Laser Scanning Standards ..................................................................................................... 12 7.2.1 Laser Scanning Tilt ......................................................................................................... 12 7.2.2 Laser Scanning Curvature .............................................................................................. 12 Technical Specifications .............................................................................................. 13 8.1 Barcode Test Sample ............................................................................................................. 13 8.2 Scan Area and Depth of Field ................................................................................................ 14 8.3 Printed Contrast Signal (PCS) ............................................................................................... 15 8.4 Minimum Resolution ............................................................................................................... 15 8.5 Pitch, Skew and Tilt ................................................................................................................ 15 8.6 Curvature ................................................................................................................................ 16 Environmental Specifications ...................................................................................... 16 9.1 Temperature ........................................................................................................................... 16 9.2 Humidity.................................................................................................................................. 16 9.3 Ambient Light Immunity .......................................................................................................... 17 9.4 Dust and Drip Proof ................................................................................................................ 17 9.5 Vibration Strength (without packing) ...................................................................................... 17 9.6 Vibration Strength (in individual packing) ............................................................................... 17 9.7 Drop Impact Strength (without packaging) ............................................................................. 18 9.8 Drop Impact Strength (in individual packaging) ..................................................................... 18 9.9 Electrostatic Discharge Immunity ........................................................................................... 18 10 Regulatory Compliance ................................................................................................ 19 10.1 LED Safety ............................................................................................................................. 19 10.2 Product Safety ........................................................................................................................ 19 10.3 EMC........................................................................................................................................ 19 10.4 Other....................................................................................................................................... 20 SPECIFICATIONS MANUAL OPN-2102i 1st 11 RoHS .............................................................................................................................. 20 12 Reliability ....................................................................................................................... 20 13 Precautions.................................................................................................................... 20 13.1 Precaution against Laser Light ............................................................................................... 20 13.2 Handling ................................................................................................................................. 21 13.3 Radio Law............................................................................................................................... 21 13.4 Bluetooth ................................................................................................................................ 22 13.5 Frequency Band ..................................................................................................................... 22 14 Product Labels .............................................................................................................. 23 15 Packaging Specifications ............................................................................................. 24 15.1 Individual Packaging .............................................................................................................. 24 15.2 Collective Packaging .............................................................................................................. 25 16 Physical Features.......................................................................................................... 26 16.1 Dimensions ............................................................................................................................. 26 16.2 Weight .................................................................................................................................... 26 16.3 Mechanical Drawing ............................................................................................................... 26 17 Supported Symbologies ............................................................................................... 27 17.1 Default Setting ........................................................................................................................ 27 17.2 Supported Symbologies ......................................................................................................... 27 17.2.1 1D Barcodes ................................................................................................................... 27 17.2.2 GS1 Databar, Composite Code ...................................................................................... 28 Table of Figures Figure 1: Detailed View ........................................................................................................................... 9 Figure 2: micro USB B Connector ......................................................................................................... 10 Figure 3: Interface Circuit (USB) ........................................................................................................... 10 Figure 4: Laser Scanning Specification ................................................................................................. 12 Figure 5: Scan Area and Depth of Field ................................................................................................ 14 Figure 6: Pitch, Skew and Tilt ................................................................................................................ 15 Figure 7: Curvature................................................................................................................................ 16 Figure 8: Drop Test................................................................................................................................ 18 Figure 9: Product Label Position ........................................................................................................... 23 Figure 10: Individual Packaging ............................................................................................................ 24 Figure 11: Collective Packaging ............................................................................................................ 25 Figure 12: Mechanical Drawing ............................................................................................................. 26 SPECIFICATIONS MANUAL OPN-2102i 1st 1 Abstract This manual provides specifications for the OPN-2102i compact laser data collector with built-in Bluetooth. 2 Overview The OPN-2102i is compact battery powered portable laser scanner with a build-in wireless battery charger. Below are some of the key features: • The OPN-2102i is a handy and simple to use data collector. • The scanned barcode data can be transmitted to a host device through the USB interface or via the build-in Bluetooth interface. • The scanner can work with many Bluetooth enabled host devices, such as PCs, tablets and smart phones. • Bluetooth SPP (Serial Port Profile) and HID (Human Interface Device Profile) are implemented. • Built-in NFC tag allows for “tap to connect” on supported telephones which greatly simplifies the pairing process of Bluetooth. • A red LED aiming line toward a target bar code can help the users find the appropriate scanning position. • Alcohol can be used to wipe the scanner clean • The power source is a 3.7 V 600 mAh (typ.) Li-ion polymer battery. • The OPN-2102i supports wireless charging and a dedicated charging cradle, the CRD-3000 is available for that. The OPN-2102i can also be charged via its USB interface. • The scanner is Apple MFi certified. SPECIFICATIONS MANUAL OPN-2102i 1st 3 Basic Specifications Item Specification Control Section Input Section Indicator RTC CPU 32 bit CISC / 96 MHz FROM 512 Kbyte + 32 Kbyte SRAM 96 Kbyte FROM (storage) 1 Mbyte Key type 2 key: trigger, function LED 2 bi-colors LEDs (red, green) and 1 blueLED Buzzer Loudness (3-level) / tone adjustable Vibration motor Strength (3-level) / duration adjustable Contents Year, month, date, hour, minute, second Accuracy ± 90 seconds per month Interface Bluetooth Note For data area only Data and time are lost when the main battery is removed. Frequency 2402 ~ 2480 MHz Specification Bluetooth Ver 2.1 compliant Communication distance 10 m Not guaranteed. Output level Class 2 Max output 4 dBm Profile SPP / HID ISO/IEC 14443 TYPE A, TYPE B JISX6319-4 ・Full-Speed 12Mbps ( HID/COM ) ・Hi-Power Bus-powered supported NFC tag USB Optical Section Light-emitted element Red laser diode Laser wavelength / output 650±10nm 1mW or less Scan rate 100±20scan/sec Symbologies JAN,EAN,UPC-A,UPC-E,NW-7 (Codabar), Industrial 2 of 5,Interleaved 2 of 5, Code 11,Code 39,Code 93,Code 128 Refer to Section 17. for details Minimum resolution Code 39 : 0.076mm PCS 0.9 Wavelength in temperature 25℃ Supported 1D Symbologies R ≥ 15 mm ( 8-digit JAN) R ≥ 20 mm (13-digit JAN) 100 mm wide 0.2 mm resolution Code 39 (DOF 150 mm) is readable: Curvature Barcode width PCS 0.9 Pitch : α ≦±35° Scan angle Skew : β ≦±50° (Excluding dead zone) Tilt Depth of Field Code 39 PCS 0.9 : γ ≦±20° Resolution (1.0) 50 ~ 420 Resolution (0.5) 45 ~ 340 Resolution (0.25) 40 ~ 250 Resolution (0.15) 40 ~ 155 Resolution (0.127) 45 ~ 130 SPECIFICATIONS MANUAL Item Specification Power Section Minimum PCS 0.3 or more Main battery Lithium-polymer 600 mAh (typ.) Up-time 25 hours or more Feeding system Electromagnetic guidance wireless charging, microUSB Operating (charging) voltage 4.5 ~ 5.5V Current consumption Charging Less than 500 mA Operating -10 ~ 50°C Storage -20 ~ 60°C Operating 20 ~ 85% Storage 20 ~ 85% Fluorescent 4,000 lx or less Sunlight 80,000 lx or less Temperature Environmental Specifications Humidity Ambient light immunity OPN-2102i 1st Note MRD 32% or more *1 Charging with USB No condensing No frost 10 Hz ~ 100 Hz, acceleration of 19.6 m/s2, 60 minutes per cycle, repeat once in each X, Y and Zdirection Drop the scanner 18 times (6 faces x 3) from a height of 150 cm onto a concrete floor Vibration Drop Dust and drip proof IP54 equivalent JIS C 6802:2011 Class2 IEC 60825-1 Ed.2: 2007 Class 2 CDRH Class Ⅱ EN60950-1:2005 IEC60950-1:2006 EN 55024:2010 EN 55032:2012+AC: 2013 EN 301 489-1 V1.9.2 EN 301 489-17 V2.2.1 EN 300 328 V1.9.1 EN 302 291-2 V1.1.1 FCC Part 15 Subpart C, Subpart B ClassB VCCI Class B LED safety Product safety Regulatory Compliance EMC For residential, commercial and lightindustrial environments CE Marking European conformity Bluetooth logo certification MFi license Other Immunity Test ESD Certification for Construction Design of Specified Radio Equipment No distraction No malfunction Air discharge (direct): ±15 kV Air discharge (direct): ±8 kV Physical Features Dimensions 83.0 × 36 × 21.5 (WDH mm) Weight Approx. 60 g Conditions: IEC61000-4-2 compliant Excluding accessories *1: When a barcode is read twice every 10 seconds at room temperature in a constant Bluetooth connection (SPP master mode). SPECIFICATIONS MANUAL OPN-2102i 1st 4 Detailed View Figure 1: Detailed View No Name Scan Window Description The laser light is emitted through this window. Ensure that the lens is not exposed to dust and dirt before scanning. USB Cap Cap for USB connector part used to make the scanner IP54 water tight. Trigger Key Press this key to enable the laser and start reading barcodes. Function Key The function of this key depends on the installed application. LED Indicates operating status, such as bar code reading, Bluetooth connection, warning etc. Buzzer Orifice Holes for buzzer. Strap Orifice Holes for attaching a hand strap. Charging Coil NFC The charging coil is located here with which the dedicated cradle can supply power to the scanner. This is the location of the NFC tag. Hold an NFC reader close to this area when the tag has to be read. SPECIFIICATIONS MANUAL OPN-2102i 1st 5 Ele ectrical Specifica ations 5.1 USB Su upply Voltage Bu us-power (Cllass) Cu urrent consu umption 5.2 : 4.5-5.5V : 500mA m max (hi-powe er) : Less tha an 500mA Wireless Charging Fe eeding system Po ower consum mption : Electrom magnetic indu uction : Less tha an 5W 6 Intterface Specifica ations The OPN N-2102i supp ports two typ pes of interfacces; USB an nd Bluetooth. 6.1 USB Interfa ace Interface is Fu ull Speed USB interface. 6.1.1 Connectorr Signal Name Contact Num mber VCC DATA A(-) DATA A(+) (NC C) GND Figure 2: micro US SB B Connecttor 6.1.2 USB Interfa ace Circuitt USB Connect ctor Pow wer Sup pply Microcontroller Figure 3:: Interface Circ cuit (USB) 10 SPECIFICATIONS MANUAL 6.2 OPN-2102i 1st Bluetooth The specifications of the OPN-2102i Bluetooth interface are as follows: Frequency : 2402 ~ 2480 MHz 6.3 Specification : Bluetooth Ver 2.1 compliant Communication distance : 10 m Output level : Class 2 (max 4 dBm) Implemented profile : SPP / HID Communication configuration : 1 to 1 Operating mode in communication : Master / Slave mode Security mode : Authentication supported Encryption : Encryption supported NFC Tag OPN2102i has NFC tag built-in which record Bluetooth device address. Frequency: 13.56MHz Standard : Recorded Contents: ISO/IEC 14443 TYPE A, TYPE B and JISX6319-4 Total 928 byte NDEF Record #1 type: ”application/vnd.bluetooth.ep.oob” OOB data length: 8 Byte MAC address: 00:12:6A:xx:xx:xx Record #2 type: ”T” TEXT data length: 15 Byte TEXT data: ”00126Axxxxxx” Free area Reserved area *xx will differ according to product. Rewriting from external: possible 7 Optical Specifications 7.1 Basic Specifications Item Unit Characteristics Light-Emitting Element Red laser diode Emission Wavelength 650 ±10 (25° C) nm Light Output < 1.0 μW Scanning Method Bi-directional scanning Scanning Speed 100 ±20 scans/sec 54 ±5 deg 44 (Min) deg Scan Angle Scan Angle Effective Scan Angle 11 SPECIFICATIONS MANUAL 7.2 7.2.1 OPN-2102i 1st Laser Scanning Standards Laser Scanning Tilt Vertical differences between both ends of a laser scanning line: - Up to 1.2 degrees in a vertical direction from the scan origin (scanning mirror). - Up to 3.1 mm measured at 150 mm from the scan origin and with zero skew angle. - Measure in the middle of the scanning line. 7.2.2 Laser Scanning Curvature The maximum differences between the laser scanning line and a straight line connecting the both ends of the scanning line: - Up to 1.27 degrees from the scan origin (scanning mirror). - Up to 3.3 mm measured at 150 mm from the scan origin. - Measure in the middle of the scanning line. Figure 4: Laser Scanning Specification 12 SPECIFICATIONS MANUAL OPN-2102i 1st 8 Technical Specifications Ambient conditions are as follows unless otherwise specified in each section:Ambient Temperature and Humidity Room temperature, room humidity Ambient Light 500 ~ 900 lx Barcodes Refer to Section 8.1. Background Power supply voltage Black 5V (USB) Accept the performance with 10 consecutive successes in reading. Each reading should be done in 0.5 seconds or less. Reading Test 8.1 Barcode Test Sample Resolution 1.0 mm 0.5 mm 0.25 mm 0.25 mm 0.15 mm 0.127 mm 0.076mm Symbology PCS Code 39 0.9 Symbology PCS JAN 0.9 Quiet Zone ( mm 25 18 mm 10 mm 10 mm 7 mm 5 mm 5 mm No. of Digits 10
Resolution 0.26 mm 0.26 mm Quiet Zone ( mm 10 10 mm No. of Digits 13 13 SPECIFICATIONS MANUAL Scan Area and Depth of Field The scanner is able to read in the area between the two arcs that are centered on the scan origin with a center line distance from the front of the scanner as indicated for each resolution. Resolution No. of Digits Depth of Field (mm) 1.0mm 50 ~ 420 0.5mm 45 ~ 340 0.25mm 40 ~ 250 0.15mm 10 40 ~ 155 0.127mm 45 ~ 130 Barcode Angle : Code 39 specified in Section 8.1. : α = 0°, β = + 15°, γ = 0° 0" 2" 4" 6" 8" 50 100 150 200 10" 14" 12" 16" 18" 20" 22" 24" [ inch ] [ mm ] 350 400 450 500 550 600 10" 300 8" 200 0.25mm ( 10mil ) 7" 175 Code 39 6" 150 0.15mm ( 6mil ) 5" 125 4" 100 0.127mm ( 5mil ) 3" 75 2" 50 25 1" 0" 25 1" 50 2" 75 3" 100 4" 125 5" 150 6" 7" 175 200 8" 225 9" 250 250 Figure 5: Scan Area and Depth of Field 14 [ inch ] 1.0mm ( 40mil ) 10" 250 9" 225 0.5mm ( 20mil ) [ mm ] 8.2 OPN-2102i 1st SPECIFICATIONS MANUAL 8.3 OPN-2102i 1st Printed Contrast Signal (PCS) PSC 0.3 or higher (70% or higher reflectivity of space and quiet zone) PCS = Reflectance of white space – Reflectance of black bar Reflectance of white space Note: Be sure to keep the optical window clean without dirt or scratches, or it may have a detrimental effect on the reading characteristics. 8.4 Minimum Resolution Minimum Resolution 0.076mm Barcode Distance Angle 8.5 Code 39 specified in Section 8.1 60 mm from the front edge of the scanner Skew angle β = 15° Pitch, Skew and Tilt Pitch Skew Dead Zone Tilt Bar code Distance Curvature Angle : α ≦ ±30° : β ≦ ±50° (Excluding dead zone) : β ≦ ±8 ° (Decoding may fail in some areas as a result of specular reflection) : γ ≦ ±20° Resolution 0.25 mm, 9-digit Code 39 specified in Section 8.1. Resolution 0.26 mm, JAN-13 specified in Section 8.1. 100 mm from the edge of the scan engine R=∞ Pitch angle : β = +15°, γ = 0° Tilt angle : α = 0°, β = +15° Skew angle / Dead zone: α = 0°, γ = 0° β γ Figure 6: Pitch, Skew and Tilt 15 SPECIFICATIONS MANUAL 8.6 OPN-2102i 1st Curvature 8-digit JAN: 13-digit JAN: Barcode Distance Angle R ≧ 15 mm R ≧ 20 mm Resolution 0.26 mm, JAN specified in Section 8.1. 100 mm from the edge of the scan engine Skew angle β = +15° バーコード Bar code Figure 7: Curvature Note: The reading performance may deteriorate if there is specular reflection of the laser light, this typically will occur when the reflectivity of the barcode is high. 9 Environmental Specifications 9.1 Temperature Scanning performance is guaranteed when the ambient temp. is within the following range: Operating Temperature: Storage Temperature : -10 ~ 50 °C -20 ~ 60 °C Please charge when the temperature is between 0 and 40°C. When the temperature is over 40°C, charging may stop to prevent battery breakdown.. 9.2 Humidity Scanning performance is guaranteed when the ambient humidity within following range: Operating Humidity: 20 ~ 85%RH (no condensation, no frost) Storage Humidity: 20 ~ 85%RH (no condensation, no frost) 16 SPECIFICATIONS MANUAL 9.3 OPN-2102i 1st Ambient Light Immunity Scanning performance is guaranteed when the illumination on a barcode surface is between zero and the following values: Incandescent light: Fluorescent light: Sunlight: Barcode: Distance: Angle: Curvature: Power-supply voltage: 4,000 lx 4,000 lx (excluding high-frequency lighting) 80,000 lx Optoelectronics Test Sample Resolution 0.25 mm, 9-digit Code 39, Quiet Zone 10 mm, N/W Ratio = 1 : 2.5 100 mm from the front edge of the scanner α = 0°, β =+15°, γ = 0° R=∞ 5.0V * Avoid direct or specula reflection from the laser beam as it may blind the scanners optical receiver. 9.4 Dust and Drip Proof IEC IP54 equivalent Protection against solid objects: Level 5 equivalent (Dust proof type) Prevent dust ingress to inside. Even if slight dust intrusion will not inhibit normal operation. Protection against liquids: Level 4 equivalent (Splash proof type) Protected against water splash from any direction. * () is JIS drip-proof type. 9.5 Vibration Strength (without packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in non-operating state. Repeat this in each X, Y and Z direction. 9.6 Vibration Strength (in individual packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state. Repeat this in each X, Y and Z direction. 17 SPECIFICATIONS MANUAL 9.7 OPN-2102i 1st Drop Impact Strength (without packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop the scanner 18 times in total (3 times at each 6 face), from a height of 150 cm onto a concrete floor as shown below. 150cm Figure 8: Drop Test 9.8 Drop Impact Strength (in individual packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges, and 6 faces, from a height of 150 cm onto a concrete floor. 9.9 Electrostatic Discharge Immunity Air discharge ±8 kV max. (No malfunction) ±15 kV max. (No destruction) Measurement environment Discharge resistance Charging capacitor An electrostatic testing device compliant with IEC 61000-4-2 330 Ω 150 pF 18 SPECIFICATIONS MANUAL OPN-2102i 1st 10 Regulatory Compliance 10.1 LED Safety JIS C 6802:2011 Class 2 IEC 60825-1 Ed.2: 2007 Class 2 CDRH Class Ⅱ 10.2 Product Safety EN60950-1:2005 IEC60950-1:2006 10.3 EMC R & TTE Directive ・EN 55024:2010 ・EN 55032:2012+AC: 2013 ・EN 301 489-1 V1.9.2 ・EN 301 489-17 V2.2.1 ・EN 300 328 V1.9.1 ・EN 302 291-2 V1.1.1 FCC Part 15 Subpart C, Subpart B ClassB Federal Communications Commission Notices This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Harmful Interference Notice This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment or devices • Connect the equipment to an outlet other than the receiver's • Consult a dealer or an experienced radio/TV technician for assistance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 19 SPECIFIICATIONS MANUAL OPN-2102i 1st VC CCI Class B This is a Class B product, to be b used in a do omestic enviro onment, based d on the Tech nical equirement of the t Voluntary Control Coun cil for Interfere ence from Info ormation Techhnology Re Equipment (VCC CI). If this is us sed near a rad dio or televisio on receiver in a domestic ennvironment, it ay cause radio o interference. ma 10.4 O Other ・Bluetooth lo ogo certification ・MFi license “Made forr iPod,” “Made for iPhone,” a and “Made forr iPad” mean that an electronic accessory ha as been design ned to pecifically to iP Pod, iPhone, o or iPad, respectively, connect sp and has be een certified by b the develop per to meet Ap pple performance standards.Apple is not re esponsible forr the operation of o this device or its complian nce with safetty and regulatory standards. Please note tha at the use of th his accessory with iPod, iPh hone, or iPad may affect wirreless performance. ・Certification n for Construc ction Design n of Specified d Radio Equipment ・Classifica ation of Specified Radio Equ uipment ・Model Na ame ・Certificate e Number Article 2 Para agraph 1, Item m 19 Low poower data ccommunicatio on system in 2.4 GHz band OPA-26X1 201-125603 11 Ro oHS Ro oHS complia ance. Ro oHS: The resstriction of the use of certtain hazardous substances in electriccal and ele ectronic equipment, 2011 1/65/EU 12 Re eliability MTBF (M Mean Time Between Failures) 50,0 000 hours 13 Precaution ns 13.1 Precaution against Laser Ligh ht ・ Do not stare into the las ser light from m the scannin ng window. m your eyes. It may harm ・ Do not poin nt the laser directly at oth hers’ eyes. It may harm m their eyes. ・ Do not stare into the be eam with optiical instrume ents. It may harm your eyes. ・ Use of conttrols or adjus stments or pe erformance of o procedures other than those speciffied herein mayy result in haz zardous radiiation exposu ure. 20 SPECIFICATIONS MANUAL OPN-2102i 1st 13.2 Handling Handle this product carefully. Do not deliberately subject it to any of the following. (1) Shock: ・ Do not drop this product from a height greater than specified in this manual. ・ Do not place this product under or between any heavy items. ・ Do not swing the cable around. (2) Temperature Conditions: ・ Do not use this product at temperatures outside the specified range. ・ Do not pour boiling water on this product. ・ Do not throw this product into a fire. (3) Foreign Materials: ・ Do not immerse this product in water or other liquid. ・ Do not expose this product to chemicals. Others ・ Do not disassemble this product. ・ Do not use this product near a radio or a TV. It may cause reception problems. ・ This product may be affected by a momentary voltage drop caused by lightning. ・ Please use within the range of operating voltage. Using outside of operating voltage may cause malfunction. ・ Do not attach piece of metal or metal foil to the back of charging coil stored part and NFC coil stored part. Also, do not fix anything that prevents placing to charging cradle. ・ Please securely close the USB cap to keep the waterproof. ・ Do not pull strong, fold and bend the cables. ・ Do not add shock or apply load to jack and connector. ・ When charging is completed, please remove USB cable from connector. 13.3 Radio Law This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data communication system and has obtained the Certification for Construction Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan. The following activities are prohibited under the Radio Law: ・Remodelling and disassembly ・Peeling off the certificate label Do not use this equipment under the following environment, as radio interference may affect other device and end up with causing physical or material damage. ・Safety apparatus and medical device for human body protection ・Environment where is concerned to cause serious damage 21 SPECIFICATIONS MANUAL OPN-2102i 1st 13.4 Bluetooth ・This product supports Bluetooth wireless communication with other Bluetooth devices that have the same profile ・This product complies with Bluetooth standards; however, its communication performance with untested devices is not guaranteed. ・Bluetooth devices use the 2.4 GHz frequency band that is shared among other devices. It may affect the communication speed and distance between this product and the host device. ・The communication speed and distance vary depending on the interference and radio wave condition between this product and the host device. 13.5 Frequency Band This product uses the 2.4 GHz frequency band. Read carefully the followings before using this product. In the frequency band of this product, scientific, medical and industrial devices including microwaves are used. Also other radio stations including local private radio station for mobile object identification requiring license for such as manufacturing lines at factories, specific power-saving radio station requiring no license and amateur radio station are managed. 1. Make sure that “other radio stations” are not managed in the frequency band 2.4 GHz before using this product. 2. In case that radio interference occurs between this product and “other radio stations,” change the service space immediately, or stop transmitting radio wave to avoid the interference. 3. If you have any questions or troubles, please contact our sales office. * This specification manual is subject to change without prior notice. 22 SPECIFICATIONS MANUAL OPN-2102i 1st 14 Product Labels The product labels are affixed to the scanner as shown below. Figure 9: Product Label Position 23 SPECIFIICATIONS MANUAL OPN-2102i 1st 15 Pa ackaging g Specific cations 15.1 In ndividual Packaging Asssembled pa ackage size: Approx. 125 5 × 112 × 40 (WDH mm) Weight: Appro ox. 140g OPN-20 012i Place intto the box with h folded side do own without ta aped. *Place with w Opticon lo ogo upward. Display for the Serial--No. 『 『123456』 123456=Producct serial numbe er. Displayy 6-digets serial number. Place the MiicroUSB cable with conne ector far side. Place with h taped side backk ward. Place pro oduct in front side, and place neck strap p to the USB cable connecto or side, th han place QSG G on the top. Individuual box label: 3A0002 OPN-21 102i-WHT *UF2O OPN2102* *Do not fold d the barcode w when pasting *UF2O OPN2102* Figure 10 0: Individual Packaging 24 SPECIFIICATIONS MANUAL OPN-2102i 1st 15.2 C Collective Packaging 10 00pcs per bo ox Asssembled pa ackage size Weight: Appro ox. 15kg : Approx. 5 595 × 520 × 245 2 (WDH mm) Thhe order of serial-No. Packing box: 5B0008 (100pcs perr box) Enter battery tyype 「Lithium ion battery」and phon ne number 「01-24 422-31-31」. And place 1pc next to either side of the packing box label. 5 Ste teps *13962* *OPN2102I--09* Figure 11 1: Collective Packaging 25 SPECIFICATIONS MANUAL OPN-2102i 1st 16 Physical Features 16.1 Dimensions 83.0 × 36.0 × 21.5 (DWH mm) 16.2 Weight Approx. 60 g (excluding accessories) 16.3 Mechanical Drawing Unit: mm Figure 12: Mechanical Drawing 26 SPECIFICATIONS MANUAL OPN-2102i 1st 17 Supported Symbologies 17.1 Default Setting The scanner is set to default by reading the following menu label. Recorded contents of the NFC tag will also return to default. Function Menu label Menu code _ZZ_ _SO_ _ZZ_ SET Default END ZZ SO ZZ 17.2 Supported Symbologies 17.2.1 1D Barcodes Code type UPC UPC Add-on 2 UPC Add-on 5 EAN (JAN) EAN Add-on 2 EAN Add-on 5 EAN-13 EAN-13 Add-on 2 EAN-13 Add-on 5 EAN-8 EAN-8 Add-on 2 EAN-8 Add-on 5 Code 39 Default ○ Minimum length ○ Note ○ ○ ○ Not transmit ST/SP Tri-Optic ○ Not transmit ST/SP Codabar (NW7) ○ Not transmit ST/SP Industrial 2 of 5 ○ Interleaved 2of 5 ○ S-Code Code 128 ○ Code 93 ○ IATA ○ MSI/Plessey ○ UK/Plessey TELEPEN GS1 conversion (setting required) ○ Code 11 Matrix 2 of 5 Chinese Post Matrix 2 of 5 Korean Postal Authority 27 SPECIFICATIONS MANUAL OPN-2102i 1st 17.2.2 GS1 Databar, Composite Code Code type GS1 DataBar ・GS1 DataBar Omnidirectional ・GS1 DataBar Truncated ・GS1 DataBar Stacked ・GS1 DataBar Stacked Omnidirectional GS1 DataBar Limited GS1 DataBar Expanded ・GS1 DataBar Expanded ・GS1 DataBar Expanded Stacked Default Note GS1 conversion (setting required) 28
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Producer : Acrobat Distiller 8.3.1 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2016:10:24 19:17:28+09:00 Create Date : 2016:10:24 19:17:28+09:00 Format : application/pdf Title : Microsoft Word - SS16056(SS16017)_P-X44Ri_Preliminary_160527_Eng.docx Creator : kokamoto3218 Document ID : uuid:50f43ace-8974-4823-9b4d-7064505d60f9 Instance ID : uuid:2bde7fb6-02f9-4767-a776-2ac122b1c2e8 Page Count : 28 Author : kokamoto3218EXIF Metadata provided by EXIF.tools