ORION ELECTRIC M210A DVD/VCR TV Interface Device User Manual 2F3PJ01A E Cover

ORION ELECTRIC CO., LTD. DVD/VCR TV Interface Device 2F3PJ01A E Cover

UserManual.wiki >

ORION ELECTRIC >

M210A User Manual

Users Manual

RDVD PLAYER/Hi-Fi VIDEO CASSETTE RECORDEROWNER'S MANUALBefore operating the unit, please read this manual thoroughly.ATTENTIONIf you purchase a universal remote control from your local retailer, please contact theremote manufacturer for the required programming code.TV/CABLE MODE SELECTIONWhen shipped from the factory, the TV/CABLE menu option is set to the “CABLE”(Cable TV) mode.If not using CABLE (Cable TV), set this menu option to the “TV” mode.VRDVD4100BAIF CONTACT WITH CUSTOMER SERVICE IS REQUIREDPLEASE HAVE THE MODEL NUMBER READY PRIOR TO THE CALLCUSTOMER SERVICE – 1-800-289-0980ORION WEBSITEFOR INFORMATION ON OUR OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE ATwww.orionsalesinc.com 2F3PJ01A[E] Cover 11/2/05, 11:41 AM1DRAFT

2WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAINOR MOISTURE.CAUTION:THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FORFUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCA-TION-SEE SERVICE PROCEDURE.USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIEDHEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASERRADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM.Location of the required MarkingThe rating sheet and the safety caution are on the rear of the unit.RISK OF ELECTRIC SHOCKDO NOT OPENCAUTIONThe lightning flash with arrowheadsymbol, within an equilateral triangle isintended to alert the user to the presenceof uninsulated dangerous voltage withinthe product's enclosure that may be ofsufficient magnitude to constitute a riskof electric shock to persons.The exclamation point within an equilateraltriangle is intended to alert the user tothe presence of important operating andmaintenance (servicing) instructions inthe literature accompanying the appliance.CAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK). NO USER-SERVICEABLE PARTSINSIDE. REFER SERVICING TO QUALIFIEDSERVICE PERSONNEL.WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference toradio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with the FCCRules could void the user's authority to operate this equipment.CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCESTANDARDS, 21 CFR SUBCHAPTER J. 2F3PJ01A[E](02-05) 11/2/05, 11:46 AM2

31. READ INSTRUCTIONSAll the safety and operating instructions should be read before the unit is operated.2. RETAIN INSTRUCTIONSThe safety and operating instructions should be retained for future reference.3. HEED WARNINGSAll warnings on the unit and in the operating instructions should be adhered to.4. FOLLOW INSTRUCTIONSAll operating and use instructions should be followed.5. CLEANINGUnplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use a damp cloth for cleaning the exterior cabinet only.6. ATTACHMENTSThe manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.7. WATER AND MOISTUREDo not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, ornear a swimming pool.8. ACCESSORIESDo not place this unit on an unstable cart, stand, tripod, bracket, or table.The unit may fall, causing serious injury, and serious damage to the unit.8A. An appliance and cart combination should be moved with care. Quick stops,excessive force, and uneven surfaces may cause the appliance and cartcombination to overturn.9. VENTILATIONSlots and openings in the cabinet back or bottom are provided for ventilation,to ensure reliable operation of the unit, and to protect it from overheating.These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed,sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unitshould not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and/or themanufacturer’s instructions have been adhered to.10. POWER SOURCESThis unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of thetype of power supply to your home, consult your appliance dealer or local power company. For units intended to operatefrom battery power, or other sources, refer to the operating instructions.11. GROUNDING OR POLARIZATIONThis unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). Thisplug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into theoutlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Donot defeat the safety purpose of the polarized plug, if your unit is equipped with a 3-wire grounding-type plug, a plughaving a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This too, is a safety feature. If youare unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat thesafety purpose of the grounding-type plug.12. POWER-CORD PROTECTIONPower-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon oragainst them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit fromthe appliance.13. LIGHTNINGTo protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug itfrom the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning andpower line surges.14. POWER LINESAn outside antenna system should not be located in the vicinity of overhead power lines or other electric light or powercircuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme careshould be taken to keep from touching such power lines or circuits, as contact with them might be fatal.15. OVERLOADINGDo not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.16. OBJECT AND LIQUID ENTRYDo not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts thatcould result in fire or electric shock. Never spill or spray any type of liquid into the unit.17. OUTDOOR ANTENNA GROUNDINGIf an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded toprovide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code,ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding ofthe lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connec-tion to grounding electrodes, and requirements for the grounding electrode.18. SERVICINGDo not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or otherhazards. Refer all servicing to qualified service personnel.S3125APORTABLE CART WARNING(symbol provided by RETAC)IMPORTANT SAFEGUARDS 2F3PJ01A[E](02-05) 11/1/05, 16:573

4EXAMPLE OF ANTENNA GROUNDING AS PER THENATIONAL ELECTRICAL CODECONDENSATIONMoisture will form in the operating section of the DVD/VCR if the player is brought from cool surroundings into a warm roomor if the temperature of the room rises suddenly. When this happens, the DVD/VCR's performance will be impaired.To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or make sure that theroom temperature rises gradually.Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air conditioner. In suchcases, change the location of the DVD/VCR.19. DAMAGE REQUIRING SERVICEUnplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:a. When the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into the unit.c. If the unit has been exposed to rain or water.d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that arecovered by the operating instructions, as an improper adjustment of other controls may result in damage and willoften require extensive work by a qualified technician to restore the unit to its normal operation.e. If the unit has been dropped or the cabinet has been damaged.f. When the unit exhibits a distinct change in performance, this indicates a need for service.20. REPLACEMENT PARTSWhen replacement parts are required, be sure the service technician uses replacement parts specified by the manufac-turer or those that have the same characteristics as the original part.Unauthorized substitutions may result in fire, electric shock or other hazards.21. SAFETY CHECKUpon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determinethat the unit is in proper operating condition.22. HEATThe product should be situated away from heat sources such as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat.23. DISC TRAYKeep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.24. CONNECTINGWhen you connect the product to other equipment, turn off the power and unplug all of the equipment from the walloutlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the otherequipment carefully and follow the instructions when making any connections.25. LASER BEAMDo not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. Itmay cause sight damage.26. DISCDo not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injuryand product malfunction.27. NOTE TO CABLE TV SYSTEM INSTALLERThis reminder is provided to call the CABLE TV system installer’s attention to Article 820-40 of the NEC that providesguidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the groundingsystem of the building, as close to the point of cable entry as practical.ANTENNADISCHARGE UNIT(NEC SECTION 810-20)ANTENNA LEAD IN WIREGROUNDING CONDUCTORS(NEC SECTION 810-21)GROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)GROUND CLAMPELECTRIC SERVICEEQUIPMENTNEC-NATIONAL ELECTRICAL CODES2898AIMPORTANT SAFEGUARDS 2F3PJ01A[E](02-05) 11/1/05, 16:574

6ContentsIMPORTANT SAFEGUARDS .................................. 3Features ................................................................... 5Contents ................................................................... 6Parts and functions .................................................. 7Remote control ......................................................... 8Power source ........................................................... 9Basic connections .................................................. 10Antenna to DVD/VCR connection ..................... 10DVD/VCR to TV connection .............................. 10CABLE TV connections ......................................... 11Playback connections ............................................ 12Setting up the VCR section .................................... 14Setting the video channel.................................. 14Setting the language ......................................... 14Auto clock setting .............................................. 15Manual clock setting ......................................... 16Tuner setting ..................................................... 16To add/delete channels..................................... 16Noise elimination ............................................... 16Tape playback operation ........................................ 17Loading and Unloading a cassette tape............ 17Cassette tape playback..................................... 17Special playback ............................................... 17ZERO RETURN function .................................. 18Video index search system ............................... 18Recording ............................................................... 19Recording a TV program ................................... 19One-touch Timer Recording (OTR)................... 20Timer recording ................................................. 20Advanced function of VCR section ........................ 22Stereo recording and playback ......................... 22Second Audio Program (SAP) .......................... 22Duplicating a video tape.................................... 22Disc playback operation ......................................... 23Disc ................................................................... 23Setting setup language ..................................... 23Playback procedure .......................................... 24Special playback ............................................... 24Zooming ............................................................ 24Locating desired scene ..................................... 25Marking desired scenes .................................... 25Changing soundtrack language ........................ 25Subtitles ............................................................ 25Changing angles ............................................... 26Title selection .................................................... 26DVD menu ........................................................ 26Repeat playback ............................................... 26Program playback (CD) .................................... 26Random playback (CD)..................................... 27MP3 playback ................................................... 27Advanced function of DVD section ........................ 28Parental control ................................................. 28Temporary disabling of rating level byDVD disc ........................................................... 28Setting language ............................................... 29Setting the aspect ratio of TV screen ................ 29Setting the picture mode ................................... 29Setting on screen display .................................. 30Status display of disc ........................................ 30Dynamic Range Control .................................... 30Progressive scan .............................................. 30Language code list ................................................. 31Problems and troubleshooting ............................... 32Video head cleaning .............................................. 33Specifications ......................................................... 34 2F3PJ01A[E](06-09) 11/1/05, 16:576

7Parts and functionsPOWER CHANNELVCR DVDVCR/DVDVIDEO IN L - AUDIO IN - RDVDVCRFrontFF (Fast Forward) buttonVCR/DVD mode selector buttonREW (Rewind) button REC buttonDVD indicatorPOWER buttonCHANNEL / buttonsAUDIO (L/R)/VIDEO IN jacks Remote sensorDisplay windowSTOP buttonPLAY buttonOPEN/CLOSE buttonDisc trayEJECT buttonCassette Loading SlotDisplay windowDVD indicatorProgressive scanning indicatorPause indicatorPlay indicatorVCR indicatorREC indicatorTRK indicatorVideo tape indicatorTimer recording indicatorVCR indicatorCD indicatorPM indicatorNumber indicator (Track playing time or other information)RearNOTE:Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.AC power cordDVD/VCR common AUDIO (L/R)/VIDEO OUT jacksDVD COAXIAL DIGITAL AUDIO OUT jackDVD S-VIDEO OUT jackRF IN jackDVD AUDIO (L/R) OUT jacksDVD COMPONENT OUT jacks RF OUT jack 2F3PJ01A[E](06-09) 11/1/05, 16:577

8Remote controlPOWER [9]EJECT [17]0 – 9 [16]SETUP [23]VCR MENU [14]CH / [9]TRK/SET + / – [14]Cursor Buttons [15]DVD MENU [26]STOP [17] [24]SKIP [24]INDEX + / – [18]ZOOM [24]MARKER [25]AUDIO [25]AUDIO SELECT [22]SUBTITLE [25]ATR [18]REC/OTR [19]JUMP [25]ZERO RETURN [18]OPEN/CLOSE [24]VCR/DVD [9]TIMER REC [20]INPUT SELECT [22]PROGRESSIVE [30]DISPLAY [15] [25]RETURN [23]TOP MENU [26]ENTER [14]CANCEL [21]PLAY [17] [24]PAUSE/STILL [18] [24]SEARCH + / – [17] [24]REPEAT A-B [26]SLOW [18] [24]ANGLE [26]COUNTER RESET [18]CLOCK/COUNTER [18]TV/VCR [14]PLAY MODE [26]SPEED [19] 2F3PJ01A[E](06-09) 11/1/05, 16:578

9Remote control / Power sourceTO USE AC POWER SOURCEUse the AC polarized line cord provided for operation on AC. Insert the ACcord plug into a standard 120V 60Hz polarized AC outlet.NOTES:•Never connect the AC line cord plug to other than the specifiedvoltage (120V 60Hz). Use the attached power cord only.•If the polarized AC cord does not fit into a non-polarized ACoutlet, do not attempt to file or cut the blade. It is the user’sresponsibility to have an electrician replace the obsolete outlet.•If you cause a static discharge when touching the unit and theunit fails to function, simply unplug the unit from the AC outletand plug it back in. The unit should return to normal operation.Polarized AC Cord Plug(One blade is wider than the other.)AC OutletWider Holeand BladePower sourceInserting Batteries123Operation•Aim the remote control at the remote sensor and press control buttons to operate.•Operate the remote control within 30° angle on either side of the remote sensor,up to a distance of Approx. 5 meters.Replace the compartmentcover.Install two “AAA” batteries (notsupplied), paying attention to thepolarity diagram in the batterycompartment.Open the batterycompartment cover in thedirection of the arrow.Battery precautionsThe precautions below should be followed when using batteries in this device:1. Use only the size and type of batteries specified.2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversedbatteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possiblebattery leakage.5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (Follow battery manufactur-er’s directions).•Press POWER to turn the DVD/VCR on or off.•Press CH or CH to move through the channels one channel at a time.•The CH / and SET +/– are also used to navigate on-screen menu system.•You can directly access specific channels using Number keys pad.•Each press of VCR/DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the DVDscreen (DVD mode).Remote control basicsApprox. 5 meters 2F3PJ01A[E](06-09) 11/1/05, 16:579

10Basic connections75 ohm coaxialcable (supplied)DVD/VCRSplitter 75 ohm input75/300 ohm outputs(not supplied)DVD/VCR75 ohm coaxial cable(supplied)Splitter 75 ohm input300 ohm output(not supplied)DVD/VCR75 ohm coaxial cable(supplied)This DVD/VCR has a single 75 ohm output for connection to aTV. If your TV has separate VHF and UHF antenna inputs (num-bers 2 and 3 below), use a splitter to connect the DVD/VCR tothe TV for VHF and UHF reception. Antenna to DVD/VCR connectionThe DVD/VCR must be connected “between” the antenna andthe TV. First, disconnect the antenna from the TV and connectit to the DVD/VCR. Then connect the DVD/VCR to the TV.Below are 3 common methods of connecting an antenna sys-tem to a DVD/VCR. Find the type of antenna system you areusing and follow the connection diagram. DVD/VCR to TV connectionAfter you have connected the antenna to the DVD/VCR, youmust connect the DVD/VCR to the TV.Below are 3 common methods of connecting your DVD/VCRto a TV. Find the type of TV you are using and follow the con-nection diagram.Example 1: Combination VHF/UHF antenna with 75 ohmcoaxial cableExample 2: Combination VHF/UHF antenna with 300 ohmtwin lead (flat) wireExample 3: Separate VHF and UHF antennasNOTE:If both VHF and UHF antennas have 300 ohm twin lead (flat)wires, use a combiner having two 300 ohm inputs and one 75ohm output.NOTES:•A clear picture will not be obtained by the main unit unlessthe antenna signal is good. Connect the antenna to themain unit properly.•For better quality recording, an indoor antenna or a telescopicantenna is not recommended. The use of an outdoor typeantenna is required.•If you are not sure about the connection, please refer toqualified service personnel.Example 1: TV with single 75 ohm VHF/UHF antennainputExample 2: TV with 300 ohm UHF and 75 ohm VHFantenna inputsExample 3: TV with 300 ohm UHF and 300 ohm VHFantenna inputs75 ohm coaxialcableDVD/VCR300 ohm twin lead(flat) wireDVD/VCRMatching transformer300 ohm input 75 ohmoutput (not supplied)VHF UHFDVD/VCR300 ohm twinlead (flat) wire75 ohm coaxialcableCombiner75/300 ohm inputs75 ohm output (not supplied)VHF/UHFIN (ANT)UHFVHFUHFVHFNOTE:If a VHF or UHF antenna is used, set the TV/CABLE menuoption to the “TV” mode.TVTVTV 2F3PJ01A[E](10-17) 11/1/05, 16:5710

11Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converterbox, except for those channels which are intentionally scrambled. If you subscribe to a special channel which is scrambled, youmust have a descrambler box for proper reception.CABLE TV connectionsNOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the outputof the Converter/Descrambler box, usually channel 3 or 4.ALLOWS: *Recording of nonscrambled channels.*Use of the programmable timer.*Recording of one channel while watching another.ALLOWS: *Recording of channels through the converter box(scrambled and unscrambled).*Using the programmable timer to record only thechannel selected at the converter box.PREVENTS: *Recording one channel while watching another.*Using the DVD/VCR tuner to select channels.DVD/VCRIncoming CableTVConverter/DescramblerIncomingCableTVIncoming CableConverter/DescramblerTVALLOWS: *Recording of nonscrambled channels.*Use of the programmable timer.*Recording an unscrambled channel while watching anychannel selected at the converter box.PREVENT: Recording scrambled channels.To record from converter/descrambler, DVD/VCR tuner must be tuned to the converteroutput channel, usually channel 3 or 4.If you are playing a tape or using the tunerbuilt into the DVD/VCR, the converter mustbe set to the video channel output of the DVD/VCR (either 3 or 4).NOTE:NOTE:DVD/VCRDVD/VCRExample 1:Example 2:Example 3: 2F3PJ01A[E](10-17) 11/1/05, 16:5711

12Playback connectionsConnect to a TV with Audio/Video OutputYou can enjoy playback by connecting the unit to a TV.Connect the unit to a TV equipped with audio input (L/R) and video input jacks using the supplied audio/video cable.Connect to a TV with S-Video Output (for DVD/CD playback)If your TV has an S-VIDEO input, you can get higher quality by connecting it with the S-VIDEO output of the unit using the S-video cable instead of connecting the video input of the TV to the VIDEO jack of the unit.The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent on the modeland features of each component. Check the Owner's Manual provided with each component for the location of video and audioinputs and outputs.Connect to a TV with Component Video Output (for DVD/CD playback)You can enjoy high quality picture by connecting the unit’s COMPONENT VIDEO OUT jacks to the COMPONENT VIDEO INjacks of your TV with the COMPONENT video cables (not supplied).NOTES:•When connecting to a TV using the VIDEO or S-VIDEO jack, make sure that the PROGRESSIVE indicator on thedisplay window is not lit. If it is lit, the VIDEO and S-VIDEO outputs do not feed the correct signals and you cannotsee any picture. To turn off the PROGRESSIVE indicator, make the Progressive scanning mode inactive(See page 30).•When the component video input jacks on a TV is of the BNC type, use an adapter to convert a pin jack to a BNC jack(not supplied).To Audio (R) InputTo Audio (L) InputTo VideoInputAudio (L) OutputAudio (R) OutputVideo OutputDVD/VCRTVAUDIO/VIDEO cable (supplied)DVD/VCRTVS-Video cable (not supplied)To Audio (R) InputTo Audio (L) InputS-Video OutputAUDIO cable (not supplied)Audio (L) OutputAudio (R) OutputTo S-VideoInputCOMPONENT VIDEO cable (not supplied)TVDVD/VCRTo ComponentVideo InputTo ComponentVideo Output AUDIO cable (not supplied)Audio (L) OutputAudio (R) OutputTo Audio (L) Input To Audio (R) Input 2F3PJ01A[E](10-17) 11/1/05, 16:5712

13Connect to an AV Amplifier with built-in digital surroundIf you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as DolbyDigital by using the Coaxial Digital Output.Use this connection to connect an:• AV amplifier with built-in *Dolby Digital decoderConnect to a Stereo Amplifier with Audio OutputYou can enjoy high quality audio by connecting the audio output to your amplifier.Connect the AUDIO OUT jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier.NOTES:•••The DVD OUTPUT jacks (COAXIAL, AUDIO L/R, S-VIDEO and COMPONENT) are useful only for DVD section. The VHSsignal is output only from the composite jacks (DVD/VCR OUTPUT) and UHF/VHF OUT.When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL to ON on the AV Amplifier. If you do,a loud noise will suddenly come out from the speakers, affecting your ears or causing the speakers to be damaged.This unit does not apply to DTS audio out. There will be no sound output if connected to AV amplifier with built-in DTS decoder.Video cable (not supplied) To VideoInputCoaxial digital cable (not supplied)AV Amplifier withbuilt-in variousdecoder as aboveDVD/VCRTVNOTE:You may connect to a TV with a Compo-nent video cable (not supplied) or S-Video cable (not supplied) instead of avideo cable (not supplied).To Audio (L) InputTo Audio (R) InputAUDIO cable (not supplied)Stereo AmplifierDVD/VCRAudio (R) OutputAudio (L) OutputCoaxial Digital Audio OutputVideo OutputPlayback connections 2F3PJ01A[E](10-17) 11/1/05, 16:5713

14To view playback of a recorded tape or DVD disc, or towatch a program selected by the VCR's channelselector, the TV must be set to channel 3 or 4 (videochannel). Setting the video channelWhen a TV is connected with the 75 ohm coaxial cable only.1Press and hold 3 or 4 on theremote control for 3 secondsin the standby mode to selectCH 3 or 4. The selected chan-nel number will flash on the display for about 4 seconds.2Turn ON the TV and set to CH 3 or 4 to correspond withthe channel selected in step 1.3Press POWER to turn on the DVD/VCR.4Press VCR/DVD to select the VCR mode. The VCRindicator on the front panel will light.5Press TV/VCR to select the VCR position.The VCR indicator will appear in the display.6Select any channel to receive a TV station in your area.The channel number will appear on the screen for about4 seconds.For a push-button TV tunerIf CH 3 or 4 corresponding to the video channel cannot betuned on your TV, proceed as follows: set the VCR 3/4channel selector and the TV to CH 3 or 4, playback aprerecorded tape and tune the TV to receive a sharp colorpicture from the video cassette recorder. Refer to your TVowner's manual for details.NOTES:•When shipped from factory, the video channel is set toCH 3.•If the unit does not operate properly, or No key opera-tion (by the unit and/or the remote control): Static elec-tricity, etc., may affect the player's operation. Disconnect theAC power cord once, then connect it again.NOTES:•Both the VCR and the DVD have their own menu option(See page 23).•If no buttons are pressed for more than 60 seconds, theMENU screen will return to normal TV-operation automati-cally.You can choose from three different languages(English, French and Spanish) for the on-screen displays. Setting the language⟨+/-/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SETUPSYSTEM SETUP⟨+/-/ENTER/MENU⟩SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFFON OFF1Press VCR MENU.The VCR menu screenwill appear. Press SET +or – to select the“SYSTEM SETUP” menu,then press ENTER.If you use the unit for thefirst time and press VCRMENU, instead of the main menu screen on the right the“SYSTEM SETUP” menu screen in step 2 may appear.2Press SET + or – to selectthe “LANGUAGE” option,then press ENTER.3Press SET + or – to selectthe desired language: En-glish (ENGLISH), Spanish(ESPAÑOL) or French(FRANCAIS), then pressENTER.4Press VCR MENU until the MENU screen is cleared.Setting up the VCR section 2F3PJ01A[E](10-17) 11/1/05, 16:5714

15The Auto clock function will automatically set the built-in clock (Month, Day, Year and Time) when the DVD/VCR is connected to an Antenna or Cable system and itis turned off. As the DVD/VCR searches for a receivablestation in your area and it receives a broadcast signalfor Auto clock, the Auto clock needs several minutes toset itself. Auto clock setting1Connect the Antenna or Cable system.• If you use a cable box, turn it on.2Plug the AC Power cord to the AC outlet.3Make sure the DVD/VCR is turned off.• If you press POWER, the Auto clock set is not effective.4After the clock is set on the display window, pressPOWER.•Depending on the reception condition, it may take approx.thirty minutes.5Press DISPLAY to check the clock on the screen.6If the clock is not set, check the Antenna condition. TheAuto clock may not function properly if the reception con-dition is not good.The Auto clock adjustment will be performed at 6:00 AM, 12:00PM and 6:00 PM everyday if you turn off the DVD/VCR.•If you use a cable box and you want Auto clock adjustmentto be performed, the cable box must be left on.•The Auto clock adjustment is not effective when there is adifference of more than 5 minutes exists between thebuilt-in clock time and the actual time.Auto clock adjustmentWhen shipped from factory, the “AUTO CLOCK” option is setto ON.But if you do not want Auto clock set (adjustment):1Turn on the DVD/VCR.2Press VCR MENU.3Press SET + or – to select the “SYSTEM SETUP’ option,then press ENTER.4Press SET + or – to select the “AUTO CLOCK” option.5Press ENTER to select “OFF”.6Press VCR MENU repeatedly to return to the normalscreen.•When the “AUTO CLOCK” is set to “OFF”, the Auto Clockadjustment does not function.•Set the clock manually (see page 16).To set Auto clock to offIn the rare event that you live within broadcast range of twostations in two different time zones, the DVD/VCR mayrecognize the wrong station for the Auto clock set.To correct the situation:1Press VCR MENU.2Press SET + or – to select the “SYSTEM SETUP”option, then press ENTER.3Press SET + or – to select the “STANDARD TIME”option, then press ENTER.To set standard time4Press SET + or – to select your time zone, then pressENTER.ATLANTIC : GMT – 4 hours(GMT: Greenwich Mean Time)EASTERN : GMT – 5 hoursCENTRAL : GMT – 6 hoursMOUNTAIN : GMT – 7 hoursPACIFIC : GMT – 8 hoursALASKA : GMT – 9 hoursHAWAII : GMT – 10 hoursAUTO : AUTO SET5Press VCR MENU twice to return to the normal screen.NOTE:To be able to select the standard time, the clock must firstbe set by “AUTO CLOCK” once.1Press VCR MENU. Press SET +or – to select the “SYSTEMSETUP” option, then pressENTER.2Press SET + or – to select the“DAYLIGHT SAVING TIME”option, then press ENTER.3Press SET + or – to select one ofthe options, then press ENTER.Press VCR MENU until theMENU screen is cleared.ON: for manual setting(forward one hour)OFF: for manual setting(back one hour)AUTO: for automatic setting(read XDS in the signal)NOTES:•When shipped from factory, the “DAYLIGHT SAVINGTIME” option is set to “AUTO” position.•When the clock is not set, Daylight Saving Time setting isnot available.•When there is no Daylight Saving Time in your area, alwaysselect “OFF” position in step 3.When you want to set the Daylight Saving Time manually, onthe first Sunday in April you set to “ON”, and on the last Sun-day in October you set to “OFF”.You can set the Daylight saving time automatically ormanually.Daylight saving time setting⟨+/-/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SETUPSYSTEM SETUP⟨+/-/ENTER/MENU⟩SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFFON OFFSetting up the VCR section 2F3PJ01A[E](10-17) 11/1/05, 16:5715

16You must set the date and time manually for TimerRecordings, ON/OFF Timer and Daylight Saving Time ifthe Auto clock process did not set them correctly.Example: Setting the clock to “8:30 AM”, 25th (SAT) March,2005.1Press VCR MENU.Press SET + or – to select the“SYSTEM SETUP” option, thenpress ENTER.2Press SET + or – to select the“CLOCK SET” option, then pressENTER.3Press SET + or – to set the month,then press ENTER.4Set the day, year and time as instep 3.After setting the clock, date and timestarts functioning automatically.NOTES:•After a 30 minute power failure or disconnection of thepower plug, the time display will be lost. In this case, setthe present time again if the Auto clock did not set correctly.•To move cursor backward, press CANCEL.1Press VCR MENU.Press SET + or – to select the “CHSETUP” mode, then press ENTER.This DVD/VCR is equipped with a channel memoryfeature which allows channels to skip up or down to thenext channel set into memory, skipping over unwantedchannels. Before selecting channels, they must beprogrammed into the DVD/VCR’s memory. In addition tonormal VHF and UHF channels, this DVD/VCR canreceive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CABLE menu option tothe TV mode. When shipped from the factory, this menuoption is in the CABLE mode. Tuner settingTV/CABLE selection1Press VCR MENU.Press SET + or – to select the“CH SETUP” mode, then pressENTER.2Press SET + or – to select the“ADD/DELETE” mode, then pressENTER.3Select the desired channel to bememorized or deleted using SET+ or – button, or using Numberkeys.4Press ENTER to select the “ADD” or “DELETE”.5Press VCR MENU until the MENU screen is cleared. To add/delete channels1In the “CH SETUP” menu, pressSET + or – to select “AUTO CHMEMORY”, then press ENTER.2The DVD/VCR will begin memoriz-ing all the channels available inyour area.4Press VCR MENU until the MENU screen is cleared.2Press SET + or – to select the TV/CABLE mode.3Press ENTER to select the TV orCABLE mode.The arrow indicates the selectedmode.TV - VHF/UHF channelsCABLE- CABLE TV channelsAutomatic memory tuningThe VCR can receive a maximum of 181 channels bypresetting the channels into memory.⟨+/-/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SETUPSYSTEM SETUP⟨+/-/ENTER/MENU⟩SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFFON OFF⟨+/-/ENTER/CANCEL/MENU⟩MONTHDAYYEARTIME 325 (SAT)2006 8 : 30 AM Manual clock settingYou can add the channels you want or delete the chan-nels you do not want manually. Noise eliminationWhen you don't want to receive a weak signal broad-cast, the Blue back screen can be obtained by selectingthe NO NOISE BACKGROUND “ON”. When the unit isshipped from the factory, the NO NOISE BACKGROUNDis set to the “ON”.1In the “SYSTEM SETUP” menu,press SET + or – to select “ NONOISE BACKGROUND”.2Press ENTER to select the “ON”or “OFF”.3Press VCR MENU until the MENU screen is cleared.⟨+/-/ENTER/MENU⟩SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDON OFFAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFFSetting up the VCR section 2F3PJ01A[E](10-17) 11/1/05, 18:1116

17Push the center of the tape until it is automatically retractedinto the unit.Automatic power on and playWhen loading a cassette tape without the erase preventiontab intact, the unit will turn on automatically and playback willstart immediately.Insert the cassette with its labeled side facing you.An inverted video cassette cannot be inserted.Use only video cassette tapes marked .LoadingTo unload a video cassette, press EJECT on the remotecontrol, or press 5 (EJECT) on the unit.UnloadingAutomatic ejectIf the unit automatically rewinds the tape to thebeginning (AUTO REWIND FEATURE), the tape willbe ejected automatically (See page 19).After recording, break off the erase prevention tab if you donot wish to record over the tape.To prevent accidental erasureErase prevention tabScrewdriverCover the hole with adhesive tape.Be careful the tape does not extend past the edges of thevideo cassette housing.To record againAdhesive tapeNOTES:•This unit selects the playback tape speed SP, LP or SLPautomatically.•The Cassette tape and DVD disc can be played back simul-taneously. If you press VCR/DVD, the tape playback andDVD playback alternate with each other on the screen.Load a prerecorded tape (When loading a cassette tapewithout the erase prevention tab, playback will start auto-matically).To start playbackPress PLAY to begin playback.“” will appear on the screen.Press STOP once.The tape will stop, but remain fully loaded and ready to play.“ ” will appear on the screen.To stop playbackPress REW or F.FWD in the Stop mode.“” or “ ” will appear on the screen.FORWARD/REVERSE PICTURE SEARCHIf you want to see the tape during REW or F.FWD mode,press and hold the REW or F.FWD. The backward or forwardvisual search picture will be seen on the screen. Release toreturn to the REW or F.FWD mode.To rewind or forward the tape rapidly Loading and Unloading a cassette tape Cassette tape playbackVideo cassette tapeTape SpeedSLP (Super Long Play)T-160 T-120 T-602-2/3 hours 2 hours 1 hour8 hours 6 hours 3 hoursSP (Standard Play)Reverse picture search functionPress REW x 1 or x 2 during the playback.Picture SearchForward picture search functionPress F.FWD x 1 or x 2 during the playback.To return to playback: Press PLAY.Still PicturePress PAUSE/STILL during playback. To resume normalplayback: Press PLAY.PICTURE SEARCH SPEEDPRESS TWICETAPE SPEED PRESS ONCESP (Standard Play)LP (Long Play)SLP (Super Long Play)5 X9 X15 X3 X7 X9 XSPEED SEARCH TIMES Special playbackTape playback operation 2F3PJ01A[E](10-17) 11/1/05, 16:5717

18Press PAUSE/STILL during playback.Press SLOW one by one: The picture advances frame byframe.To return to playback: Press PLAY or PAUSE/STILL.Frame by Frame PictureSlow tracking and vertical lock adjustmentIf noise bars appear in the picture during slow motion, pressthe TRK + or – to reduce the noise bars.If the still picture jitters excessively, press TRK + or – tostabilize the still picture.Press DISPLAY.The counter display shows the taperunning time during playback or re-cording.This function makes tape-rewinding stop at the counter00:00:00 position automatically.Press COUNTER RESET at thedesired tape position. The counterdisplay will be reset to the“00:00:00” position (e.g. the beginning of recording).2Press STOP when playback or recording is finished.Press ZERO RETURN.The tape will be rewinded or fast forwarded and automati-cally stop at the “00:00:00” position.The CLOCK/COUNTER-buttonPress CLOCK/COUNTER. The clock and tape counter alter-nate with each other in the display.13 Video index search systemThis function enables you to locate the beginning of anyrecording made on the VCR.Recording an INDEX MARKThe Index Search function automatically records an INDEXmark on the tape whenever a recording is initiated.Index SearchPress INDEX 77777 or 66666 during stop or play mode.For Succeeding programs: Press INDEX 77777.For Preceding programs: Press INDEX 66666 .(Additional press increases the INDEX NO. up to 9.)When the INDEX 77777 or 6 6 6 6 6 is pressed, the unit startssearching the INDEX NO. selected and finds the portion,then playback starts automatically.To stop the Index Search, press STOP.NOTES:When you record an INDEX mark at the very beginning of thetape, the mark may not be found.During INDEX search, the tape may stop and begin to playat a slightly different location.INDEX may not function properly with old or worn out videotapes.INDEX marks may not be found if it is extremely close to thepoint where the search began.In recording, if you stop recording temporarily, the INDEXmark is not recorded on the tape.•••••VCRVCR ZERO RETURN functionSlow MotionDuring playback press SLOW.To return to playback: Press PLAY or SLOW.Adjusting tracking conditionWhenever you insert a tape and start playback, automatictracking starts working and continuously analyzes the signalto enable optimum picture quality during playback.Automatic tracking adjustmentRepeat playbackThe entire video tape will be played until its end. The tape willthen automatically rewind to the beginning and the playbackwill be repeated.1Press VCR MENU. Press SET + or – to select “AUTOREPEAT”.3Press VCR MENU until the menu screen is cleared.if you press DISPLAY, “” will appear on the screen.Then press ENTER to se-lect “ON” or “OFF”.If “ON” is selected, the play-back will be repeated end-lessly.4To start the playback, press PLAY.The playback will be repeated endlessly.2To cancel repeat mode:Follow the above step 1, then press ENTER to select theOFF position. Press VCR MENU to return to the TV.NOTES:•The audio output is muted during Picture Search, Still PictureSlow Motion and Frame by Frame Picture.•During Picture Search mode there will be noise bars which arecaused by the system.•The Special Playback will automatically change to playbackafter approx. 5 minutes to protect the video tape against ex-cessive wear.If automatic tracking cannot eliminate noises well duringplayback, press TRK +/– to eliminate the noises.“MANUAL TR.” will appear. Press it briefly for a fine adjustment,or press and hold for a coarse adjustment.• Press ATR to reactivate automatic tracking again.“AUTO TR.” will appear.Manual tracking adjustment NOTES:If you rewind the tape beyond “00:00:00”, a minus sign(“–”) will be displayed in front of the time.When you load a tape, the counter will reset to “00:00:00”.The counter does not function on nonrecorded (blank) sec-tions of the tape. When you rewind, fast forward or play tapesthrough blank sections, the counter stops.•••Tape playback operationMENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SETUPSYSTEM SETUP 2F3PJ01A[E](18-23) 11/1/05, 16:5718

19CH 110INDEX8 : 30AM MON00 : 15 : 12 SPHI-FICH 1258 : 47AM MON00 : 00 : 00 SPSTEREO SAPRecording and viewing the same TV program.NOTES:•If the erase prevention tab is removed, the tape will eject whenREC/OTR is pressed for recording.•If you wish to watch the DVD playback during the normalrecording on VCR, press VCR/DVD to change to DVD modeand perform the DVD playback (see page 24).•You can not record disc material in DVD, Audio CD, etc. ontoa video tape with this DVD/VCR.3Load a cassette tape with the erase prevention tab intact.The unit will automatically turn on.Set the TV/CABLE option to the appropriate position(see page 16).12Press SPEED to select the desired tape speed SP orSLP.The tape counter and SP or SLP will appear on thescreen for about 4 seconds.4Press Number keys or CH / to select the channelto be recorded.VHF/UHF/CABLE CHANNELS5Press REC/OTR.“ ” will appear on the screenfor about 4 seconds and “REC”will appear on the display.1-9 Press 0 twice and then 1-9 as required.Example: To select 2, Press 002.10-12 Press 0 first and then the remaining 2 digitsin order from left to right.Example: Press 012 for “12”.13-99 Press 2 digits in order.Example: Press 22 for “22”.100-125 Press the 3 digits in order.Example: Press 110 for “110”. Recording a TV programPress STOP to stop recording.“ ” will appear on screen for about 4 seconds.To stop recordingPress PAUSE/STILL to avoid recording unwanted material.“” will appear on screen for about 4 seconds.Press again to continue the recording.To stop recording temporarilyNOTES:The pause function will be released after 5 minutes to preventdamage to the tape or the VCR. The VCR will change to theSTOP mode.You can select a recording channel in the recording pausemode.••While the VCR is recording, press TV/VCR to select the TVposition.The “VCR” will go off and recording will continue.Select the TV channel you want to watch by using the TVchannel selector.Recording one program while watchinganotherNOTE:Some CABLE hookups do not permit viewing one channelwhile recording another. See page 11.To Display VCR operation StatusPress DISPLAY. The clock, day of the week and more informa-tion will be indicated.To cancel the display: Press DISPLAY until all indicatorsdisappear.While watching TVDAY OF THE WEEKCHANNELTAPESPEEDREAL TIME COUNTERCLOCKSTEREO ANDSECOND AUDIOPROGRAM (SAP)While operating a tapeOPERATINGMODETAPE INAUTOREPEATHI-FISTEREOAuto rewind featureThis VCR will automatically rewind the tape when the tape hasended (except during OTR and TIMER REC). It will also ejectthe tape.RecordingTV CABLEVHF2-13UHF14-69VHF2-13STD/HRC/IRC14-36 (A) (W)37-59 (AA) (WW)60-85 (AAA) (ZZZ)86-94 (86) (94)95-99 (A-5) (A-1)100-125 (100) (125)01 (5A) 2F3PJ01A[E](18-23) 11/1/05, 16:5719

203Load a cassette tape with the erase prevention tabintact.The unit will automatically turn on.Set the TV/CABLE option to the appropriate position.12Press SPEED to select the desired tape speed SP orSLP.The tape counter and SP or SLP will appear on thescreen for about 4 seconds.4The One-touch Timer Recording feature provides asimple and convenient way to make a timed recording.Press Number keys or CH / to select the channelto be recorded.5NOTE:If you wish to watch the DVD playback during the OTR, pressVCR/DVD to change to DVD mode and perform the DVDplayback (See page 24).Example: One-touch Timer Recording for 30 minutes.Press REC/OTR. Press the button again to stop record-ing after 30 minutes. Each additional press of REC/OTRwill increase recording time as shown in the chart below,up to a maximum of 6 hours. The OTR and recording timewill appear on the screen for about 4 seconds. And, “REC”will keep blinking in the display.Press STOP or turn off the power.“ ” will appear on screen for about 4 seconds.To cancel OTRPressoncetwice3 times4 times5 timesNORMAL REC0:301:001:302:003:004:005:006:00NORMAL RECRecording time Press 6 times 7 times 8 times 9 times10 timesRecording time3Press VCR MENU. Selectthe “TIMER REC SET”option, then press ENTER.Press SET + or – to selectthe date, then pressENTER.12Press SET + or – to selectone of the program line,then press ENTER.4Timer recording can be programmed on-screen with theremote control. The built-in timer allows automaticunattended recording of up to 8 programs within 1 month.Set the start time, end time,channel and tape speed asin step 3.Example: Program a timer recording for the 26th day,channel 125 (CABLE), 11:00 - 11:30 PM on timer programnumber 1 (Tape speed: SLP).NOTES:Press CANCEL to move cursor backward for correction.To record from external source set the channel to “L”. “L”will appear next to CH 125 (or 69).••5To enter other programs, repeat steps 2 through 4.• To return to the normal screen, press VCR MENU twice.6Press TIMER REC. The clock symbol ( ) will appearon the display and the VCR stands by for recording. Atthe same time, VCR mode will change to DVD modeautomatically. You can use DVD even if the VCR is inthe Timer recording mode.If you do not use the DVD, turn the power off.The timer recording will start at 20 seconds before thetime you predetermined.NOTES:If the clock symbol ( ) does not appear on the displayin spite of the pressing of TIMER REC, the cassette maynot have been loaded yet. (See page 17)If the cassette is ejected in spite of the pressing of TIMERREC, the erase prevention tab of the cassette may havebeen removed. (See page 17)••NOTES:If the clock symbol ( ) blinks when the timer recordingended, the TV program has not been completely recordedbecause of an insufficient tape supply. Press TIMER REC tocancel the timer program or press EJECT to remove thecassette tape.During timer recording standby mode, the VCR mode can-not be selected. To use the VCR, press TIMER REC at first,then press VCR/DVD to change to VCR mode. After you usethe VCR, press TIMER REC again to put the VCR into timerrecording standby mode.If you press TIMER REC during timer recording, the record-ing operation will be interrupted. If you press TIMER RECagain within the programmed time, the recording operationwill start again.After a 30 minute power failure or disconnection of the powerplug, all programmed recording settings and time display willbe lost upon resumption of power. In this case, reset theclock (See page 15) and reprogram any timer recordings.•••• One-touch Timer Recording (OTR) Timer recordingRecording 2F3PJ01A[E](18-23) 11/1/05, 16:5820

21Timer recording special caseWeekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-SA:Monday to Saturday) Timer recording.Follow the procedure of timer recording on the previous page.At picture 3 press SET + or – repeatedly until the desired settingappears. Then press ENTER.When you press SET – repeatedly, the indicator at DATE willchange as follows, in this case the day is Friday.In case Timer programs-overlapDo not overlap timer programs as portions of the conflictingprograms will be lost. The first recording time has priority overthe next recording time as shown in the diagram below.NOTES:The daily/weekly recording can be made continuously untilthe recording is canceled or the tape reaches the end.During timer recording the automatic rewinding mechanismdoes not function.••Confirmation / Cancellation of the Timerrecording1If the Timer has been activated, press TIMER REC todeactivate the Timer. The clock symbol ( ) will disap-pear. Then press VCR/DVD to change to VCR mode.2At picture 1 on the previouspage select the “TIMER RECSET” option and pressENTER.Then the timer program listas right will appear on thescreen.To cancel Timer program:4Press VCR MENU repeatedly until the TV-picture appears.3The current day (Friday) SU-SA (Sunday to Saturday)MO-SA (Monday to Saturday)MO-FR (Monday to Friday)WKL-WE WKL-TH (Weekly Thursday)(Weekly Wednesday)One month laterminus one dayPress SET + or – to selectthe unnecessary program,then press CANCEL to can-cel the program.To confirm Timer program:NOTES:•If there are other timer record programs remaining, TIMERREC must be pressed to reactivate the timer, otherwise theremaining timer record programs will be ignored.•You cannot confirm the Timer program during timer record-ing operation.•You can also correct the programmed setting in programconfirm mode.At step 2 above, press ENTER to enter the program inputmode. Then press ENTER repeatedly until the item you wishto correct blinks. Then correct the data with SET + or –.Then press VCR MENU repeatedly until the TV-pictureappears.Recording8 : 00 11 : 009 : 00 10 : 00Program 1Prog.1Deleted PartsNon Recorded Portion PartsProg.2 Prog.3Program 2Program 3Recording Control Settings+/–/ENTER/CANCEL/MENU DATE START END CH–––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––––26(SU)11:00PM11:30PM125SLP 2F3PJ01A[E](18-23) 11/1/05, 16:5821

22To AUDIO (L) INTo AUDIO (L) OUTAUDIO/VIDEO Cord (supplied)Playback VCRTo VIDEO OUT To AUDIO (R) OUTRecording VCRTo VIDEO IN To AUDIO (R) INAUDIO/VIDEO Cord (not supplied)To AUDIO (R) INTo AUDIO (L) INTo VIDEO INRecording VCRTo AV JackPlayback CamcorderWhen a MTS STEREO broad-cast is received, the word“STEREO” will appear on thescreen and the program can beviewed or recorded in stereo.The VHS Hi-Fi audio system permits high fidelity record-ing of MTS STEREO TV broadcasts.NOTES:When playing back a tape that is not recorded in Hi-Fi stereomode, the audio will automatically be monaural.When listening to a VHS Hi-Fi video tape or MTS broadcastthrough the VHF/UHF jack (Audio/Video cord not connected),the sound will be monaural. Stereo recording and playbackNOTE:When using a CABLE system, stereo TV programs may betransmitted over a mono cable channel. In this case the word“STEREO” will not appear and the sound will be in mono.When viewing an MTS STEREO TV program, or playing aprerecorded VHS Hi-Fi STEREO videotape, press AUDIOSELECT to select how the audio will be heard through thespeakers. Normally set to the Hi-Fi STEREO position, thisbutton can be set to the MONO position if the stereobroadcast or videotape audio is of poor quality. The “R” and“L” positions allow the audio from the Right or Left Hi-Fichannel to be heard over both TV speakers. This button hasno effect when viewing a MONO videotape or TV program.Each time when you press the button, output selectiondisplay appears on the screen for several seconds. Refer tothe chart below.Output selectionOUTPUTSELECTIONSTEREOL chR chMONOSOUND HEARD ON BOTHSPEAKERSSTEREOLEFT CHANNEL AUDIORIGHT CHANNEL AUDIOMONOYour VCR is fitted with a SAP broadcast system whichenables you to switch to a second audio program whenviewing a selected channel.This function applies only when the program is broad-cast in multi-languages through the SAP broadcastsystem. Second Audio Program (SAP)Press VCR MENU. Then press SET + or – to select“SAP”.12Then press ENTER to select “ON”.Then press VCR MENU until the menu screen is cleared.When the VCR is turned on or a channel selection is made,make certain the letters “SAP” appears on the screen. Thismeans that the “Second Audio Program” broadcasting isavailable.Listening to SAP••STEREOThe Hi-Fi STEREO recording procedure is the same as fornormal recordings.If you connect the VCR to another VCR or camcorder, youcan duplicate a previously recorded tape.Make all connections before turning on the power.Load a blank cassette tape with the erase prevention tabintact into the recording VCR.Load a previously recorded tape into the playback VCRor CAMCORDER.1Press SPEED to select the desired tape speed SP or SLP.It is recommended that you set the Speed to the SP modeon the recording VCR for best results.2Press INPUT SELECT to selectAUDIO/VIDEO input position. “L” willappear in the display.3Press REC/OTR on the recording VCR, then pressPAUSE/STILL.4Press the PLAY button on the playback VCR orCAMCORDER, then press the PAUSE/STILL button.5Release the recording pause and the playback still simul-taneously to begin the duplicating process.6 Duplicating a video tapeConnection with second Video recorderConnection with Video camera3Advanced function of VCR sectionFor duplicating a previously recorded tape from acamcorder, follow the camcorder manufacturer’s instruc-tions. A typical camcorder dubbing hookup is shown above. 2F3PJ01A[E](18-23) 11/1/05, 16:5822

23This unit applies to DVD discs from Region 1 or Region ALL.The loaded Disc (DVD, Audio-CD and MP3-CD) will be recog-nized automatically.The suitable Disc-formats are: DVD, CD-R and CD-RW.Some CD-R/RW discs may be incompatible.Do not play DVD-ROM, DVD-Audio, CDV, Video-CD, CD-G orPhoto CD to prevent accidental erasure of prerecorded material.This unit cannot record disc material in DVD, Audio CD etc.onto a video tape.If you press REC/OTR during DVD playback, a symbol mark“ ” will appear on the screen for approx. 4 seconds.TitleWhen two or more movies are recorded on a disc, the disc isdivided into two or more sections. Each section is called a“TITLE”.ChapterThe titles can be subdivided into many sections.Each section is called a “CHAPTER”.TrackAn Audio CD can contain several items.These are assigned to the tracks.CHAPTER 1TITLE 1 TITLE 2DVD DISCCHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5CDRemoving Disc from CaseBe sure to hold the edge of disc. Donot touch the surface of the disc.Pick up the disc gently from the case.•Do not scratch the disc.•Do not get dirt on the surface ofthe disc.•Do not stick a label or adhesivetape on the disc.•Do not drop or bend the disc.Storing Disc•Store the disc in the case toavoid risk of scratches, dirt ordamage.•Do not leave disc exposed to di-rect sunlight or in hot or humidplaces.Cleaning DiscWipe the disc with a clean, drycloth from center to edge.•Do not wipe the disc round.•Do not use liquid or aerosolcleaners. DiscAudio-CD Setting setup languageThe setup language can be selected.2Press SETUP in thestop mode. The SETUPMENU of DVD will ap-pear on the screen.To make the SETUP screen disappear, press SETUP (orRETURN).If the DVD/VCR does not operate properly: Static electric-ity, etc., may affect the player's operation. Disconnect the ACpower cord once, then connect it again.4Press or to select“OSD”, then press or to select desired lan-guage (e.g. English).1Press VCR/DVD to se-lect the DVD mode (TheDVD indicator will light).“No Disc” will appear onthe screen (If a DVD dischas already loaded, theplayback will start auto-matically).Disc playback operation5Press or toselect option, thenpress or ENTER.3/Enter/Setup/ReturnNo discMenuSubtitleAudioOSDEnglishEnglishEnglish/Setup/ReturnEnglishMenuSubtitleAudioOSDEnglishEnglish/Setup/ReturnEnglishEnglish 2F3PJ01A[E](18-23) 11/1/05, 16:5823

244Press PLAY or OPEN/CLOSE.The disc tray closes automatically.On the screen, “ ” changes to “Reading” and then play-back will commence.•A menu screen may appear on the TV screen, if thedisc has a menu feature. In this case, press , ,, or ENTER to operate a menu feature.1Press OPEN/CLOSE.The disc tray will open.2Place a disc onto the tray.Hold the disc, position it with the printed label side up, alignit with the guides, and place it in its proper position.3Press STOP to end playback.•The DVD/VCR memorizes the stopped point, depend-ing on the disc. “ ” appears on the screen. Press PLAYto resume playback (from the scene point).•If you press STOP again (“ ” appears on the screen)or unload the disc, the DVD/VCR will clear the stoppedpoint.5Then press OPEN/CLOSE.The disc tray opens.Remove the disc and press POWER.The disc tray closes automatically and DVD/VCR turns off.NOTES:•If a non-compatible disc is loaded, “Incorrect Disc”, “RegionCode Error” or “Parental Error” will appear on the TV screenaccording to the type of loaded disc. In this case, check yourdisc again (see pages 23 and 28).•Some discs may take a minute or so to start playback.•A “Prohibition” symbol “ ” may appear at the upper left ofthe screen. This symbol means either the feature you tried isnot available on the disc, or the DVD/VCR can not accessthe feature at this time. This does not indicate a problemwith the DVD/VCR.•When you set a single-faced disc label downwards (i.e. thewrong way up) and press PLAY or OPEN/CLOSE, “Reading”will appear and remain on the screen for approx. 40 secondsand then it will change to “Incorrect Disc”.•Some playback operations of DVDs may be intentionally fixedby software producers. Since this DVD/VCR plays DVDs ac-cording to the disc contents the software producers designed,some playback features may not be available. Also refer tothe instructions supplied with the DVDs.•When playing DTS-encoded Audio CDs, excessive noise willbe heard from the analog stereo outputs. To avoid possibledamage to the audio system, the consumer should takeproper precautions when the analog stereo outputs of theDVD/VCR are connected to an amplification system.There may be a slight delay between pressing the buttonand the function activation.Fast Forward PlaybackPress F.FWD during normal playback.Each press of F.FWD will increase the speed of the search(x2), (x4), (x8), (x20).• To resume normal playback, press PLAY.Review PlaybackPress REW during normal playback.Each press of REW will increase the speed of the search (x2), (x4), (x8), (x20).• To resume normal playback, press PLAY.Still PlaybackPress PAUSE/STILL during normal playback.• To resume normal playback, press PLAY.Frame AdvancePress PAUSE/STILL during still playback.One frame is advanced each time you press PAUSE/STILL.• To resume normal playback, press PLAY.Slow-motion PlaybackPress SLOW during normal playback or still playback.Each press of SLOW will change the speed of the slow x1/2,x1/4, x1/6, x1/7.• To resume normal playback, press PLAY.• To resume the still playback, press PAUSE/STILL.Locating a chapter or trackPress SKIP (77777) Forward or SKIP (66666) Reverse duringplayback to locate a chapter that you want to watch.Each time you press the button, a chapter or track is skipped.NOTE:The unit is capable of holding a still video image or On screendisplay image on your television screen indefinitely. If you leavethe still video image or On screen display image displayed onyour TV for an extended period of time, you risk permanentdamage to your television screen. Projection televisions arevery susceptible. Playback procedure Special playbackNOTE:You can use the Pause, Slow, Search or Skip feature in thezoom mode.This unit will allow you to zoom in on the frame image. Youcan then make selections by switching the position of theframe.1Press ZOOM during playback.The center part of the image will be zoomed in.Each press of ZOOM will change the ZOOM 1(x 1.3), 2 (x 1.5) and 3 (x 2.0).23Press C C C C C / D D D D D or B B B B B / A A A A A to view a different part of the frame.You may move the frame from the center position to UP,DOWN, LEFT or RIGHT direction. ZoomingIn the zoom mode press ZOOM repeatedly to return to a1:1 view ( Off).Disc playback operation 2F3PJ01A[E](24-27) 11/1/05, 16:5824

25Use the title, chapter and time recorded on the disc tolocate the desired point to play back.To check the title, chapter and time, press DISPLAY. (seepage 30)Press Number keys to change the number.•If you input a wrong number, press CANCEL.•Refer to the package supplied with the disc to check thenumbers.1Press JUMP duringplayback or stop mode.3Press ENTER.Playback starts.• When you change the title, playback starts fromChapter 1 of the selected title.• Some discs may not work in the above operation.42Press or to selectthe “Time”, “Title” or“Chapter”. Locating desired scene1Press MARKERduring playback.2Select the blank Markerusing / .Then press ENTER at the desired scene.•Repeat this procedure to set the other 2 scenes.3Press MARKER to remove this display.The unit stores the points that you want to watch again upto 3 points. You can resume playback from each scene.1Press MARKER duringplayback or stop mode.Returning to the scenes2Press / to selectthe Marker 1-3. Marking desired scenes3Press ENTER.Playback starts from the marked scene.Marking the scenes1Press MARKER.To cancel the mark2Press / to select the Marker 1-3.NOTES:•Some discs may not work with the marking operation.•The marking is cancelled when you open the disctray or turn the power off.•Some subtitles recorded around the marker may failto appear.3Press CANCEL.To remove this display, press MARKER.1Press AUDIO during playback.The current soundtrack lan-guage will appear.2Press AUDIO repeatedly until the desired language is selected.The on-screen display will disappear after a few seconds.You can select the language when you play a multilingualdisc. Changing soundtrack languageTurning the subtitles on and offWhen playing back a disc recorded with subtitles, you canturn the subtitles on or off.Press SUBTITLE during playback until “Off”appears.Changing the subtitle languageYou can select the language when playing back a discrecorded with multi-lingual subtitles.Press SUBTITLE repeatedly during play-back until your desired language appears.The on-screen display will disappear aftera few seconds.NOTES:•If the desired language is not heard after pressing the buttonseveral times, the language is not recorded on the disc.•Depending on the DVD you may be unable to turn on, turnoff, or change the subtitles, even if they are recorded on thedisc. While playing the DVD, the subtitle may change whileopening or closing the disc tray, or while changing the title.•In some cases, the subtitle language is not changed to theselected one immediately. SubtitlesDisc playback operationMarker 2Marker 1Marker 3/Enter/Cancel/MarkerMarker 2Marker 1Marker 3/Enter/Cancel/Marker271608542531000102Off1/32 EngTimeTitleChapter/Enter/0 9/Cancel/Jump/6// 2F3PJ01A[E](24-27) 11/1/05, 16:5825

26When playing back a disc recorded with multi-angle facility,you can change the angle that you are viewing the scenefrom.1Press ANGLE during playback.The current angle will appear.2Press ANGLE repeatedly until the desired angle is se-lected.1/9NOTE:Depending on the DVD, you may not be able to change theangles even if multi-angles are recorded on the disc. Changing anglesTwo or more titles are recorded on some discs. If thetitle menu is recorded on the disc, you can select thedesired title.Press ENTER or PLAY.The playback of the selected title will start.1Press TOP MENU during playback.Title menu appears on the screen.• Press TOP MENU again to resume playback at thescene when you pressed TOP MENU.2Press / or / to select the desired title.3 Title selectionSome DVDs allow you to select the disc contents usingthe menu. When you play back these DVDs, you canselect the subtitle language and soundtrack language,etc. using the DVD menu.Press ENTER. The menu continues to another screen.Repeat steps 2 and 3 to set the item completely.1Press DVD MENU during playback.The DVD menu appears on the screen.• Press DVD MENU again to resume playback at thescene when you pressed DVD MENU.2Press / or / to select the desired item.3NOTE:Depending on the DVD, you may be unable to select thetitle, and a “title menu” may simply be called a “menu” or“title” in the instructions supplied with the disc. DVD menuTitle, Chapter, Track PlaybackAudio-CD1Press PLAY MODE during playback or stop mode.DVD Repeat playbackNOTES:•Some discs may not work with the repeat operation.•In A-B repeat mode, subtitles near point A or B may not appear.•During the A-B Repeat Playback the ANGLE feature will notoperate.•You may not be able to set A-B Repeat, depending on thescenes of the DVD.•A-B repeat does not work with an interactive DVD and MP3-CD.A-B repeat playback allows you to repeat material betweentwo selected points.1Press REPEAT A-Bduring playback.The start point is se-lected.2Press REPEAT A-Bagain.The end point is selected.Playback starts at thepoint that you selected.Playback stops at the end point, returns to Point A automati-cally, then starts again.To resume normal playback press REPEAT A-B again.“Off” appears on the screen.A-B Repeat PlaybackAudio-CD2Press or to select “Chapter” or “Title”.In case of CD, at first press to select “Repeat” and thenpress or to select “Track” or “All”.DVD3Press PLAY MODE again to make the screen disappear.1Press PLAY MODE inthe stop mode.2Press or repeat-edly until the program ta-ble shown at right ap-pears.3Example: In case youwish to program in orderof 7, 3, 11:Enter as 7 , 3 , 11.If you input a wrongnumber, press CANCEL.4Press / or /to select “ProgramPlayback” and pressENTER. “Program Playback” will appear on the screen.The program you selected will begin to playback in theorder set. To return to normal playback, select “PlayMode: Off” at step 2 above.You can arrange the order of tracks on the disc. Program playback (CD)Press PLAY to start Repeat playback.To resume normal playback, select Repeat “Off”.••Disc playback operation:Play Mode/Play ModeOffOff:RepeatABAProgram Playback:Repeat/Play ModeOff:Repeat/Play ModeChapter:Play Mode/Play ModeOffAll:Repeat:Play Mode/Play ModeOffOff:Repeat 2F3PJ01A[E](24-27) 11/1/05, 16:5826

271Press PLAY MODE inthe stop mode.2Press / to select“Random”.3Press PLAY.“Random Play” will appear on the screen and RandomPlayback will start.NOTES:•To cancel program play, select “Clear” at step 4 and pressENTER.•The program is cancelled when you open the disc tray or turnthe power off.•Random playback can not be combined with Repeat play-back. Random playback (CD)This player can play back the MP3-data which has beenrecorded on CD-R or CD-RW. To produce the MP3-data,you need a Windows-PC with CD-ROM drive and a MP3-encoding Software (not supplied).The Apple-HFS-System can not be played.Limitations on MP3 CD playback•MP3 CD is the disc that is standardized by ISO9660, its filename must include 3-digits extension letters, “mp3”.•The directory and file names of the MP3 CD must correspondto the ISO standardized files.•This unit can read 999 files per disc. If one directory hasmore than 999 files, it reads up to 999 files, the remainingfiles will be omitted.•As for multi-session disc, only the first session can beplayed.•If the CD has both audio tracks and MP3 files, only audiotracks are played.•It may take more than one minute for this unit to read MP3files depending on its structure.•Music recorded by “Joliet Recording Specification” can beplayed back, the file name is displayed (within 10 letters) onthe screen. Long file names will be condensed.•The music files recorded by “Hierarchical File System” (HFS)cannot be played.Limitations on display•The maximum number for display is 10 letters. Availableletters for display are the following: capital or small alphabetsof A through Z, numbers of 0 through 9, and _ (under score).•Other characters than those above are replaced by ahyphen.Notes on MP3 filesTo play back MP3 CD in the recorded order,1. Use MP3 software that records data alphabetically ornumerically.2. Name each file including two-digit or three-digit number (e.g.“01” “02” or “001” “002”).3. Refrain from making too many sub-folders.CAUTION:•Some MP3 CDs can not be played back depending on therecording conditions.•The CD-R/RW that has no music data or non-MP3 files cannot be played back.MP3 CD InformationMP3 playback43A MP3 menu screen willappear on the TV screen.Press / or ENTER toselect folder.Press / or / or Number keys to select the de-sired track, then press ENTER. Track is selected and playcommences.• In case the folder includes more than 15 tracks, press or to display next track list.5Press STOP to end playback.• The unit records the stopped point. “ ” appears on thescreen. Press PLAY to resume playback (from thescene point).• If you press STOP again or unload the disc, the unit willclear the stopped point.6Then press OPEN/CLOSE.The disc tray opens.Remove the disc and press POWER.The disc tray closes automatically and DVD/VCR turns off.1Press OPEN/CLOSE.The disc tray will open.Place a disc onto the tray.2Press PLAY or OPEN/CLOSE. The disc tray closes auto-matically. On the TV-screen, “Reading” will appear. Read-ing will take as much time as the number of file.NOTES:•During MP3-Playback, you can not use SEARCH, A-B Re-peat functions.•You can use Repeat (Track or All), Random functions andProgram playback for MP3 CD Playback.Disc playback operation1-/72--:--/0-9/Enter/Play Mode2345JapanCD Bay BridgeCLOSE MY EYESDIVE TO BLUEHoney89101112flowerLies and Truth-winter fallRainStrawberry6BLUE EYES13Welcome party7Blurry Eyes14ThailandPops/0-9/Enter/Play Mode1516MotherCDHold Your LastPops-/72--:--1-/72--:--/0-9/Enter/Play Mode2345JapanCD Bay BridgeCLOSE MY EYESDIVE TO BLUEHoney89101112flowerLies and Truth-winter fallRainStrawberry6BLUE EYES13Welcome party7Blurry Eyes14ThailandPops:Play Mode/Enter/Play ModeRandomOff:Repeat 2F3PJ01A[E](24-27) 11/1/05, 16:5827

281Press SETUP in the stop mode.Press or to select option.Then press or ENTER.2Press once to select “Parental Off”, then press or until the level you desire appears (e.g.: 1).3Press once to select “Password ”.Then press Number keys to input a 4-digit password(e.g.: 1234).• If you input a wrong number, press CANCEL.• Be sure to remember this number!4Press ENTER.1234 change to .Parental control settingSome discs are specified not suitable for children. Suchdiscs can be prevented from play back with the unit.Level Off : The parental control setting does notfunction.Level 1 : DVD software for adults cannot beplayed back.Level 8 : All DVD software can be played back.Select from level 1 to level 8.On a scale of 1-8, “1” is the most restrictive.5To make SETUP screen disappear, press SETUP.1Select “Password ”(step 2) and press Numberkeys to input your 4-digitpassword.Then press ENTER.To unlock the Parental control setting2If the input password was right, will appear.You can move to “Parental 1” (e.g.) to input the desiredlevel or to cancel parental control.Cancel the password so as to set the Parental level freelyagain,NOTES:•If each setup (pages 23, 28 ~ 30) has been completed,the unit can always be worked under the sameconditions (especially with DVD discs).Each setup will be retained in the memory if you turnthe power off.•Depending on the discs, the unit cannot limit playback.•Some discs may not be encoded with specific rating levelinformation though its disc jacket says “adult”. For thosediscs, the age restriction will not work.•Do not forget the password. If you forget the password,contact customer service.NOTE:This temporary cancellation of rating level will be kept untilthe disc is ejected.When the disc is ejected, the original rating level will be setagain automatically.Depending on the DVD disc, the disc may try totemporarily cancel the rating level that you have set.It is up to you to decide whether to cancel the ratinglevel or not.If you wish to cancel the set rating level temporarily,select “Parental Control Level” with or , thenpress ENTER. If the 4-digits password at step 3 on leftcolumn has been set, the password entering screen willappear as shown in step 4 below.Alternatively, if the password has not been set, playbackwill commence. If you don’t know (or have forgotten) thepassword, select “Cancel Picture”.The setting screen will disappear. Press OPEN/CLOSEto remove the disc.1Load a DVD disc and press PLAY or OPEN/CLOSE (seepage 24).2If the DVD disc hasbeen designed totemporarily cancel theRating level, the screenwhich follows the“Reading” screen willchange, depending onwhich disc is played. Ifyou select “YES” withENTER key, “Your disc exceeds the parental control level1.” (e.g.) screen will then appear.3Enter the passwordwith Number keys.Then press ENTER.4Playback will commence if the entered password wascorrect.5If you interrupt theentering, pressRETURN.Your disc exceedsthe parental control level 1.Parental Control LevelCancel Picture/Enter/ReturnPlease enter the4digit password9/Cancel/ReturnEnter/0Temporary disabling of rating levelby DVD disc Parental controlAdvanced function of DVD sectionPasswordParentalOutput1Interlace/0-9/Enter/Cancel/Setup/Return1234PasswordParentalOutputOffInterlace/0-9/Enter/Cancel/Setup/Return---- 2F3PJ01A[E](28-BACK) 11/1/05, 16:5828

29Press or toselect your desiredlanguage.123To make SETUP screen disappear, press SETUP.Press or ENTER, then press or to select desiredoption.4You can select the language of the disc menu messagesof DVDs.Press SETUP in the stop mode.Press or to select option.English, Francais, Espanol:The selected language will be heard or seen.Other:Other language can be selected (see the “Languagecode list” on page 31).Off: (Subtitle)Subtitles do not appear.Original: (Audio)The unit will select the first priority language of each disc.NOTE:If the selected language is not recorded on the disc, the first-priority language is selected.Press or toselect your desiredscreen type.1Press SETUP in the stop mode.Press or to select option.23To make SETUP screen disappear, press SETUP.4NOTE:If the DVD disc is not formatted in the pan & scan style, itdisplays 4:3 style.You can select the aspect ratio for your TV.4:3 Letter boxSelect this mode when connecting to a conventional TV.When playing back a wide screen-DVD disc, it displaysthe wide picture with black bands at the top and bottom ofscreen.4:3 Pan ScanIt displays the wide picture on the whole screen with leftand right edges automatically cut off.16:9 WideSelect this mode when connecting to a wide-screen TV.A wide screen picture is displayed full size.Press or ENTER,then press or toselect “Tv Screen”.You have the following screen sizes to choose from: Setting language Setting the aspect ratio of TV screenAdvanced function of DVD sectionMenuSubtitleAudioOSDEnglishEnglishEnglish/Setup/ReturnEnglishTv ScreenDisplayPicture ModeOnAuto/Setup/Return4:3Press or toselect your desiredpicture mode.1Press SETUP in the stop mode.Press or to select option.23Press or ENTER, then press or to select“Picture Mode”. Setting the picture modeAuto: The unit recognizes the picture source (film orvideo) of the current disc according to the discinformation.The image of smoother motion can be obtained bysetting Picture Mode to Film when you view a DVDfrom the DVD player connected with the componentinput.Tv ScreenDisplayPicture ModeOn/Setup/Return4:3Auto 2F3PJ01A[E](28-BACK) 11/1/05, 16:5829

30On screen display can be switched on or off when youpress the DISPLAY button.The unit supports the Progressive scanning system aswell as the conventional interlaced scanning system.If your TV is equipped with component jacks whichsupport the progressive video input, you can enjoy highquality picture by making the Progressive scanningmode active.1Press PROGRESSIVE in the stop mode.The PROGRESSIVE indicator “ ” on the displaywindow will light.2Press PLAY to start playback.•To make the progressive scanning mode inactive, pressPROGRESSIVE in the stop mode.The PROGRESSIVE indicator “ ” on the displaywindow will go off.About PROGRESSIVE SCANNING MODETo display video on the TV screen, the conventionalscanning method is called “Interlaced scanning.” With thismethod, only half of the horizontal lines are displayed at atime. So two fields complete a single picture (frame); i.e.,the first field, containing all the odd-numbered lines, isdisplayed followed by the second field, containing all theeven-numbered lines.The Progressive scanning system scans all horizontallines at a time, so you can double the number of linescompared with the interlaced scanning, resulting in a high-density, flicker-free picture.To enjoy a progressive scanned video, the TV connectedto the unit must have Progressive inputs.Depending on the material source format, DVD discs canbe classified into two categories; film and video (note thatsome DVD discs contain both a film source and a videosource). Film sources are recorded as 24-frame-per-second information, while (NTSC) video sources arerecorded as 30-frame-per second (60-field-per-secondinterlaced) information.When the unit plays back a film source material,uninterlaced progressive output signals are created usingthe original information. When a video source material isplayed back, the unit interleaves lines between theinterlaced lines on each to create the interpolated pictureand outputs as the progressive signal.NOTES:•Some discs may not be played back with the progressive scan-ning mode correctly because of the disc characteristics or re-cording condition.•There are some progressive TV and High-Definition TV sets thatare not fully compatible with the unit, resulting in the unnaturalpicture when playing back a DVD disc in the Progressive scan-ning mode. In such a case, use the Interlaced scanning mode.•You cannot make the progressive scanning mode active in fol-lowing cases.– The unit is in the VCR mode.– The disc is played back in the DVD mode. Setting on screen display Progressive scanEach press of DISPLAY, the status display of the disc willappear on the screen and change as follows.DVDAUDIO CDStatus display of discTo make status display disappear, press DISPLAY again.When you playback the CD disc, the status display willappear on the screen and continue displaying.Press or to select“On” or “Off”.123To make SETUP screen disappear, press SETUP.4On: On screen displays appear when you press anybuttons (factory setting).Off: On screen displays do not appear when you pressany buttons except SETUP, SEARCH MODE,PLAY MODE, MARKER and DISPLAY.Press or ENTER, thenpress or to select“Display”.Press SETUP in the stop mode.Press or to select option.NOTES:•This function works only during playback of Dolby Digitalrecorded discs.•The level of Dynamic Range Reduction may differdepending on DVD video disc.Press or to selectdesired setting.1Press SETUP in the stop mode.Press or to select option.23Press or ENTER toselect “DRC”.DRC (Dynamic Range Control) enables you to controlthe dynamic range so as to achieve a suitable soundfor your equipment. Dynamic Range ControlOn:Loud sound such as explo-sion or similar is toned down slightly when playedback. This makes it suitable for when it is connectedto a stereo.Off:It plays back at the recording level on the disc.Advanced function of DVD sectionNOTE:You also can change the scan-ning mode by selecting Output inthe option.00:34:56 01:12:3300:34:56 01:12:331/9Title 1/991/81/32Chapter 1/999Eng DolbyDigitalEng34:56 71:33Track 11/99Tv ScreenDisplayPicture Mode/Setup/Return4:3AutoOnDRC/Setup/ReturnOffPasswordParentalOutputOffInterlace InterlaceProgressive/Enter/Setup/Return---- 2F3PJ01A[E](28-BACK) 11/2/05, 11:47 AM30

31Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925Amharic 1123 Galician 1722 Malay 2329 Spanish 1529Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931Armenian 1835 German 1415 Maltese 2330 Swahili 2933Assamese 1129 Greek 1522 Maori 2319 Swedish 2932Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121Chinese 3618 Javanese 2033Rhaeto-Romance2823 Urdu 3128Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631Language Name Code Language Name Code Language Name Code Language Name CodeEnter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” (see page 29).Language code list 2F3PJ01A[E](28-BACK) 11/1/05, 16:5831

32SYMPTOMS POSSIBLE SOLUTIONS•Make sure the power cord is plugged in.•Try another AC outlet.•Power is off, check fuse or circuit breaker.•Unplug unit, then plug it back in.•Select the DVD or VCR mode before operating.DVD/VCR does not operate.Problems and troubleshootingUse the following check list for troubleshooting when you have problems with your unit. Consult your local dealer or serviceoutlet if problems persist.Be sure all connections are properly made when using with other units.DVD/VCRPAGE9––9–The remote control does not function.• Aim at the remote control at the remote sensor.• Operate within Approx. 5 Meters or reduce the light in the room.• Clear the path of the beam.• The batteries are weak. Replace the batteries.• Check the batteries are inserted correctly.9DVDNo picture.• Antenna connection is not correct or antenna cable is disconnected.• Check the unit is connected correctly.• The video channel is not in the correct position or the TV is not set tothe video channel 3 or 4.• The video input selector of the TV is not set to VIDEO. Set to VIDEO (orequivalent).• Channel is set to the external mode.No sound. • Check the unit is connected correctly.• Check the input selector of the amplifier is set properly.• The unit is in the Special playback mode.10,1110~1314––10~13–18,24•Select proper language in the menu options.Display is not shown in your language. 23Playback doesn’t start.• No disc is inserted.• The disc may be dirty. Clean up the disc.• The unit cannot play DVD-ROMs, etc.Stopping playback, search, slow-motion play, repeat play, or programplay, etc. cannot be performed.• Some discs may not do some of the functions.242323–No CABLE reception. •Check all CABLE connections.•Station or CABLE system problems, try another station. 11Noise bars on screen.• Tracking adjustment beyond range of automatic tracking circuit. TryManual tracking adjustment.• Video heads are dirty.• The tape is worn or damaged.VCR•The erase prevention tab of the video cassette is broken off.•The unit is in the external input mode.TV recording does not work. 17,19Timer recording does not work.• The time is not set correctly.• The recording start/end time is not set correctly.• TIMER REC has not been pressed ( is not lit).15,1620201833–No picture, or the screen is blurred ordivided into two parts.• The progressive scanning mode is active through the unit isconnected to a TV via the VIDEO OUT jack.30 2F3PJ01A[E](28-BACK) 11/1/05, 16:5832

33RWHEN CALLING CUSTOMER SERVICE – PLEASE HAVE YOUR MODEL NUMBER READYOR WRITE TO:ORION SALES, INC.3471 N. UNION DR.OLNEY, ILLINOIS 62450FOR INFORMATION ON OUR OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE ATwww.orionsalesinc.comFOR CUSTOMER SERVICE,ADDITIONAL SET-UP OROPERATING ASSISTANCEPLEASE CALL:1-800-289-0980TO ORDER ACCESSORYPARTS OR LITERATUREPLEASE CALL:1-888-369-0304No subtitle. • Some discs have no subtitles.• Subtitles are cleared. Press SUBTITLE.Angle cannot be changed. • Multi-angles are not recorded on the DVD disc.• The function is prohibited with the unit or the disc. appears on the screen.25,292624SYMPTOMS POSSIBLE SOLUTIONS PAGEProblems and troubleshooting / Video head cleaningNo 4:3 (16:9) picture. • The setup does not match your TV.No on-screen display. • Select Display On.2930No surround sound. • The setup does not match your stereo system.The unit or remote operation key isnot functioning.• Turn off the unit and unplug the AC power cord for several minutes,then replug it.13Playback does not start when the titleis selected. • Check the Parental setup.Audio soundtrack and/or subtitlelanguage is not changed when youplay back a DVD. • Multilingual language is not recorded on the DVD disc.–2829NOTES: •DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE REAR COVER.•Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.•To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.Video head cleaningAuto head cleanerAuto Head Cleaning system cleans the video heads automatically whena cassette is inserted or ejected to prevent dirt from accumulating on theheads. However, manual head cleaning signifies that the head is gettingdirty and occurs when playing poor quality or damaged tapes. If theheads require cleaning, use a high quality head cleaning system or havethem cleaned professionally.Good Picture Snowy PictureVideo head cloggingThe video heads are the means by which the DVD/VCR reads the picture from the tape during playback. In the unlikely eventthat the heads become dirty enough to be clogged, no picture will be played back. This can easily be determined if, duringplayback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If this is the case, have theDVD/VCR checked by qualified service personnel. 2F3PJ01A[E](28-BACK) 11/1/05, 16:5833

34SpecificationsGENERALPower supply:Power consumption:Weight:Dimensions:Inputs/Outputs:Video:Audio:Antenna:Hi-Fi frequency response:Hi-Fi dynamic range:Video head:Audio track:Tuner:RF channel output:F.FWD/REW Timeat 25˚C (77˚F):DVD sectionSignal system:Applicable disc:Audio characteristicsfrequency response:S/N Ratio:Harmonic distortion:Wow and flutter:Dynamic range:Output:Pickup:ACCESSORIES:AC 120V 60HzOperation: 18WStand by: 2W7.7 lbs (3.5 kg)Width : 16-15/16 inches (430 mm)Height : 3-7/8 inches (99 mm)Depth : 8-15/16 inches (227 mm)In: 1 Vp-p/75 ohmsOut: 1 Vp-p/75 ohmsIn: –8 dBm/50k ohmsOut: –8 dBm/1k ohmsUHF/VHF IN/OUT: 75 ohms coaxial20Hz to 20,000HzMore than 90 dB4 Rotary HeadsHi-Fi Sound - 2 Tracks / MONO Sound - 1 Track181 Channel Freq. SynthesizedVHF 2-13UHF 14-69CABLE TV 14-36 (A)-(W)37-59 (AA)-(WW)60-85 (AAA)-(ZZZ)86-94 (86)-(94)95-99 (A-5)-(A-1)100-125 (100)-(125)01 (5A)Channel 3 or 4, SwitchableF.FWD Time: Approx. 4 minute and 50 secondsREW Time: Approx. 2 minute and 30 seconds(with T-120 Cassette Tape)NTSCDVD (12 cm, 8 cm), CD (12 cm, 8 cm)DVD: 4Hz - 22kHzCD: 4Hz - 20kHz90 dB0.02%Less than 0.01% WrmsMore than 90 dBVideo : (RCA) 1 Vp-p/75 ohmsAudio : (RCA) –12 dBm/1k ohmsDigital Audio : 0.5 Vp-p/75 ohmsCD : Wavelength: 770 - 800 nmMaximum output power: 0.7 mWDVD :Wavelength: 645 - 660 nmMaximum output power: 0.5 mWRemote control x 175 ohm Coaxial Cable x 1AUDIO/VIDEO Cable x 1VCR sectionDesigns and specifications are subject to change without notice. 2F3PJ01A[E](28-BACK) 11/1/05, 16:5834

35ORION warrants this product to be free from manufacturing defects in material and workmanship undernormal use and conditions for a period of ninety (90) days from date of original purchase in the United States only.Should service be necessary under this warranty for any reason due to a manufacturing defect or malfunc-tion during the first ninety (90) day period from date of original purchase, ORION will provide carry-in repairservice at an ORION authorized Independent Service Center at no charge. In addition, for a period of up to six(6) months from date of original purchase for video heads and twelve (12) months from date of original pur-chase for other component parts, if an original part fails due to a manufacturing defect in material or workman-ship we will replace the defective part only (EXCLUDING LABOR AFTER INITIAL NINETY (90) DAY WAR-RANTY PERIOD) provided the defect or malfunction is verified along with dated proof of purchase.There are ORION Independent Service Centers located throughout the country. For the one nearest you,DIAL TOLL FREE: 1-800-289-0980 or visit our website at www.orionsalesinc.com. This product is eligible forCARRY-IN service only. ORION will not be liable for damages incurred during shipment of the unit. If there areno ORION authorized Independent Service Centers in your area please call – 1-888-296-7466 for assistance.Note: This warranty is void if the product is:(a) Damaged through negligence, misuse, or accident.(b) Used in a commercial application or rentals.(c) Modified or repaired by anyone other than an Independent Service Center authorized by ORION to effectwarranty repairs to the class of product or by the ORION Factory Service Center.(d) Damaged because it is improperly connected to the equipment of other manufacturers.This warranty does not cover:a) Damage to tape cartridge.b) Cleaning of video heads.c) Damage to DVD and CD discs.d) Damage to equipment not properly connected to the product.e) Costs incurred in the shipping of the product to an ORION authorized Independent Service Center orORION Factory Service Center.f) Damage or improper operation of unit caused by customer abuse, misuse, negligence, or failure to followoperating instructions provided with the product.g) Ordinary adjustments to the product, which can be performed by customer as outlined in the owner'smanual.THIS WARRANTY IS NON-TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASERAND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT. ANY APPLICABLE IMPLIEDWARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED IN DURATION TO APERIOD OF THE EXPRESS WARRANTY AS PROVIDED HEREIN BEGINNING WITH THE DATE OF ORIGI-NAL PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED SHALL APPLYTO THIS PRODUCT THEREAFTER. ORION MAKES NO WARRANTY AS TO THE FITNESS OF THE PROD-UCT FOR ANY PARTICULAR PURPOSE AND USE.UNDER NO CIRCUMSTANCES SHALL ORION BE LIABLE FOR ANY LOSS, DIRECT, INDIRECT,INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITHTHE USE OF THIS PRODUCT.THIS WARRANTY IS VALID ONLY IN THE UNITED STATES OF AMERICA. THIS WARRANTY GIVESYOU SPECIFIC LEGAL RIGHTS, HOWEVER, YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROMSTATE TO STATE. SOME STATES DO NOT ALLOW LIMITATION ON IMPLIED WARRANTIES OR EXCLU-SION OF CONSEQUENTIAL DAMAGE; THEREFORE, THESE RESTRICTIONS MAY NOT APPLY TO YOU.ORION SALES, INC.3471 N. UNION DR.OLNEY, ILLINOIS 62450limitedWARRANTYDVD PLAYER / VIDEO CASSETTE RECORDER COMBINATION UNIT 2F3PJ01A[E](28-BACK) 11/1/05, 16:5835

Printed in ThailandJ2F3PJ01A SH 05/11 N 2F3PJ01A[E](28-BACK) 11/1/05, 16:5836