ORION ELECTRIC M2A7A DVD VCR Combo User Manual Manual

ORION ELECTRIC CO., LTD. DVD VCR Combo Manual

Manual

RDVD PLAYER/Hi-Fi VIDEO CASSETTE RECORDEROWNER'S MANUALBefore operating the unit, please read this manual thoroughly.ATTENTIONIf you purchase a universal remote control from your local retailer, please contactthe remote manufacturer for the required programming code.TV/CATV MODE SELECTIONWhen shipped from the factory, the TV/CATV menu option is set to the "CATV"(Cable Television) mode.If not using CATV (Cable TV), set this menu option to the "TV" mode.ORION WEBSITEFOR INFORMATION ON OUR OTHER PRODUCTS,PLEASE VISIT OUR WEBSITE ATWWW.ORIONSALESINC.COMVRDVD4000 2A70101A Cover 04/12/2001, 23:051
2WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THISAPPLIANCE TO RAIN OR MOISTURE.CAUTION:THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY ANDRETAIN FOR FUTURE REFERENCE.  SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT ANAUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSESPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.  VISIBLELASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.  DO NOT STARE INTOBEAM.Location of the required MarkingThe rating sheet and the safety caution are on the rear of the unit.CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCESTANDARDS, 21 CFR SUBCHAPTER J.RISK OF ELECTRIC SHOCKDO NOT OPENCAUTIONThe lightning flash with arrowheadsymbol, within an equilateral triangle isintended to alert the user to the presenceof uninsulated dangerous voltage withinthe product's enclosure that may be ofsufficient magnitude to constitute a riskof electric shock to persons.The exclamation point within an equilateraltriangle is intended to alert the user tothe presence of important operating andmaintenance (servicing) instructions inthe literature accompanying the appliance.CAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK). NO USER-SERVICEABLEPARTS INSIDE. REFER SERVICING TOQUALIFIED SERVICE PERSONNEL.WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.- Consult the dealer or an experienced radio/TV technician for help.CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance withthe FCC Rules could void the user's authority to operate this equipment.3CH.INOUTANT.DIGITAL AUDIO AUDIO S-VIDEO COMPONENTDVD OUTPUTLRVIDEOOPTICAL COAXIALAUDIOLR4(          )TV(       )YPB/CBPR/CR 2A70101A(02-05) 29/11/2001, 13:472
31. READ INSTRUCTIONSAll the safety and operating instructions should be read before the unit is operated.2. RETAIN INSTRUCTIONSThe safety and operating instructions should be retained for future reference.3. HEED WARNINGSAll warnings on the unit and in the operating instructions should be adhered to.4. FOLLOW INSTRUCTIONSAll operating and use instructions should be followed.5. CLEANINGUnplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use a damp cloth for cleaning the exterior cabinet only.6. ATTACHMENTSThe manufacturer of this unit does not make any recommendations for attachments, as they may causehazards.7. WATER AND MOISTUREDo not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wetbasement, or near a swimming pool.8. ACCESSORIESDo not place this unit on an unstable cart, stand, tripod, bracket, or table.The unit may fall, causing serious injury, and serious damage to the unit.8A. An appliance and cart combination should be moved with care. Quick stops,excessive force, and uneven surfaces may cause the appliance and cartcombination to overturn.9. VENTILATIONSlots and openings in the cabinet back or bottom are provided for ventilation,and to ensure reliable operation of the unit, and to protect it from overheating.These openings must not be blocked or covered. The openings should never be blocked by placing the uniton a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heatsource. This unit should not be placed in a built-in installations such as a bookcase or rack unless properventilation is provided or the manufacturer’s instructions have been adhered to.10. POWER SOURCESThis unit should be operated only from the type of power source indicated on the rating plate. If you are notsure of the type of power supply to your home, consult your appliance dealer or local power company. Forunits intended to operate from battery power, or other sources, refer to the operating instructions.11. GROUNDING OR POLARIZATIONThis unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than theother). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insertthe plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician toreplace your obsolete outlet. Do not defeat the safety purpose of the polarized plug, if your unit is equippedwith a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a ground-ing-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contactyour electrician to replace your obsolete outlet.Do not defeat the safety purpose of the grounding-type plug.12. POWER-CORD PROTECTIONPower-supply cords should be routed so that they are not likely to be walked on or pinched by items placedupon or against them, paying particular attention to cords at plugs, convenience receptacles, and the pointwhere they exit from the appliance.S3125APORTABLE CART WARNING(symbol provided by RETAC)IMPORTANT SAFEGUARDS 2A70101A(02-05) 29/11/2001, 13:473
413. LIGHTNINGTo protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to theunit due to lightning and power line surges.14. POWER LINESAn outside antenna system should not be located in the vicinity of overhead power lines or other electriclight or power circuits, or where it can fall into such power lines or circuits. When installing an outsideantenna system, extreme care should be taken to keep from touching such power lines or circuits, ascontact with them might be fatal.15. OVERLOADINGDo not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.16. OBJECT AND LIQUID ENTRYDo not push objects through any openings in this unit, as they may touch dangerous voltage points or shortout parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.17. OUTDOOR ANTENNA GROUNDINGIf an outside antenna or cable system is connected to the unit, be sure the antenna or cable system isgrounded to provide some protection against voltage surges and built-up static charges, Section 810 of theNational Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mastand supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of groundingconductors, location of antenna discharge unit, connection to grounding electrodes, and requirements forthe grounding electrode.18. SERVICINGDo not attempt to service this unit yourself as opening or removing covers may expose you to dangerousvoltage or other hazards. Refer all servicing to qualified service personnel.19. DAMAGE REQUIRING SERVICEUnplug this unit from the wall outlet and refer servicing to qualified service personnel under the followingconditions:a. When the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into the unit.c. If the unit has been exposed to rain or water.d. If the unit does not operate normally by following the operating instructions. Adjust only thosecontrols that are covered by the operating instructions, as an improper adjustment of other controlsmay result in damage and will often require extensive work by a qualified technician to restore theunit to its normal operation.e. If the unit has been dropped or the cabinet has been damaged.f . When the unit exhibits a distinct change in performance, this indicates a need for service.20. REPLACEMENT PARTSWhen replacement parts are required, be sure the service technician uses replacement parts specified bythe manufacturer or those that have the same characteristics as the original part.Unauthorized substitutions may result in fire, electric shock or other hazards.21. SAFETY CHECKUpon completion of any service or repairs to this unit, ask the service technician to perform safety checks todetermine that the unit is in proper operating condition.22. HEATThe product should be situated away from heat sources such as radiators, heat registers, stoves, or otherproducts (including amplifiers) that produce heat.23. DISC TRAYKeep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.24. CONNECTINGWhen you connect the product to other equipment, turn off the power and unplug all of the equipment  fromthe wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner'smanual of the other equipment carefully and follow the instructions when making any connections.IMPORTANT SAFEGUARDS 2A70101A(02-05) 29/11/2001, 13:474
5EXAMPLE OF ANTENNA GROUNDING AS PER THENATIONAL ELECTRICAL CODECONDENSATIONMoisture will form in the operating section of the DVD/VCR if the player is brought from cool surroundings into awarm room or if the temperature of the room rises suddenly. When this happens, DVD/VCR's performance willbe impaired.To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, ormake sure that the room temperature rises gradually.Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an airconditioner. In such cases, change the location of the DVD/VCR.25. LASER BEAMDo not look into the opening of the disc tray or ventilation opening of the product to see the source of thelaser beam. It may cause sight damage.26. DISCDo not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause seriouspersonal injury and product malfunction.27. NOTE TO CATV SYSTEM INSTALLERThis reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC thatprovides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-nected to the grounding system of the building, as close to the point of cable entry as practical.TO USE AC POWER SOURCEUse the AC polarized line cord provided for operation on AC. Insertthe AC cord plug into a standard 120V 60Hz polarized AC outlet.NOTES:•Never connect the AC line cord plug to other than the specifiedvoltage (120V 60Hz). Use the attached power cord only.•If the polarized AC cord does not fit into a non-polarized ACoutlet, do not attempt to file or cut the blade. It is the user’sresponsibility to have an electrician replace the obsolete outlet.•If you cause a static discharge when touching the unit and theunit fails to function, simply unplug the unit from the AC outletand plug it back in. The unit should return to normal operation.Polarized AC Cord Plug(One blade is wider than the other.)AC OutletWider Holeand BladePower SourceANTENNADISCHARGE UNIT(NEC SECTION 810-20)ANTENNA LEAD IN WIREGROUNDING CONDUCTORS(NEC SECTION 810-21)GROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)GROUND CLAMPELECTRIC SERVICEEQUIPMENTNEC-NATIONAL ELECTRICAL CODES2898AIMPORTANT SAFEGUARDS / Power Source 2A70101A(02-05) 29/11/2001, 13:475
6FeaturesDVD/CD Player/Video Cassette Recorder• DVD/CD player with Video Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Videocassette recorder. The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higherthan Super VHS. Audio quality is higher than audio CD. The DVD PLAYER can play back audio CDs.• High Quality Picture - More than 500 lines (VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400lines) or Laser Disc (430 lines) in resolution.VCR Section• Stereo/SAP Reception - This VCR is designed to receive stereo and separate audio program (SAP) broadcasts whereavailable.• 4 Video Heads - Provides optimal picture quality for special effects playback.• 19µm HEAD - For superior picture quality even in SLP mode, 19micron width technology heils to avoid crosstalk andboost SLP picture quality to near SP levels. With precision technology, ghosts and color beats are virtually eliminated.• Hi-Fi Stereo Sound - With a frequency response of 20 to 20,000 Hz and a dynamic range of better than 90dB, this VCRprovides a level of excellence that rivals compact discs.• One-touch Timer Recording (OTR) - Simply by pressing the REC/OTR button, the VCR can be programmed for up to 5hours of recording with an immediate start.DVD Section• Compatible with a wide range of DVD audio outputsDigital Audio Jack (Optical or Coaxial):• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect ofbeing in a movie theater or a concert hall.• Surround standard different from Dolby Digital. This format is already in use in many theaters. By connecting this unitto a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this formatcan be enjoyed. However, audio will not be output from the analog audio output jacks.• The MPEG audio of DVD discs recorded in this format can be enjoyed.• The Linear PCM sound of a 48 kHz/16 bit through 96 kHz/20 bit exceeds audio CD sound.• Multi-Language - Since this DVD matches with 124 language-subtitles/-soundtracks, you can enjoy selecting a favoriteone. (You can not select the language that is not recorded on the disc.)• Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc, youcan change the angles during playback. (If a Multi-Angle is not recorded on the disc, you can not change the angle.)• Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.• Program/Random Playback - You can play back tracks in programmed or random-selected sequences.• Zoom - You can zoom in on the selected subject on the screen during playback.• Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor/television on a suitable disc.• Parental Control - You can limit the playback of scenes or sounds of adult DVD discs which have a parental level rating.This product incorporates copyright protection technology that is protected by method claims of certain U.S. patentsand other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyrightprotection technology must be authorized by Macrovision Corporation or other rights owners and is intended for homeand other limited viewing uses only unless otherwise authorized by Macrovision Corporation or other rights owners.Reverse engineering or disassembly is prohibited.Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of DolbyLaboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe therights of copyright owners and be contrary to copyright laws.**** 2A70101A(06-11) 04/12/2001, 23:056
7ContentsIMPORTANT SAFEGUARDS .......................... 3Power Source...................................................5Features ...........................................................6Contents ...........................................................7Parts and functions .......................................... 8Display .............................................................9Remote control ............................................... 10Basic connections .......................................... 12CATV (CABLE TV) connections..................... 14Playback connection ...................................... 16Before using your unitRecording a TV program ................................ 26One-touch Timer Recording (OTR) ................ 28Timer recording .............................................. 29RecordingStereo recording and playback ...................... 31Separate Audio Program (SAP) ..................... 31Duplicating a video tape ................................. 32Advanced function of VCR sectionCassette tape playback .................................. 23Special playback ............................................ 24ZERO RETURN function................................ 25Video index search system ............................ 25Tape playback operationSetting the video channel ............................... 18Setting the language ...................................... 18Clock setting................................................... 19Tuner setting................................................... 20To ADD/DELETE channels............................. 21Noise elimination ............................................ 21Loading and Unloading a cassette tape ......... 22Setting up the VCR sectionDisc ................................................................ 33Setting setup language .................................. 34Playback procedure ....................................... 35Special playback ............................................ 36Zooming ......................................................... 37Repeat playback............................................. 38Memory playback/Random playback ............. 39MP3 playback ................................................. 40Changing soundtrack language ..................... 41Changing subtitles language .......................... 41Changing angles ............................................ 42Title selection ................................................. 42DVD menu...................................................... 42Disc playback operationParental control .............................................. 43Setting menu language .................................. 45Setting subtitle language ................................ 46Setting audio soundtrack language ................ 47Setting the aspect ratio of TV screen ............. 48Setting on screen display ............................... 49Setting Audio .................................................. 50Setting Operation ........................................... 51Setting Background ........................................ 52Setting Screen Saver ..................................... 52Setting intial setup .......................................... 53Output sound coversion table......................... 53Status display of disc ..................................... 54Table of languages ......................................... 55Advanced function of DVD sectionProblems and troubleshooting ....................... 56Video head cleaning....................................... 57Specifications ................................................. 58LIMITED WARRANTY.................................... 59Additional information 2A70101A(06-11) 04/12/2001, 23:057
8POWER CHANNELVCR DVDVCR/DVDVIDEO IN L - AUDIO IN - RDVDVCR3CH.INOUTANT.DIGITAL AUDIO AUDIO S-VIDEO COMPONENTDVD OUTPUTLRVIDEOOPTICAL COAXIALAUDIOLR4(          )TV(       )YPB/CBPR/CRParts and functionsFrontSTOP buttonRearAC power cordPLAY buttonOPEN/CLOSE buttonDisc trayPOWERbuttonDVD/VCR common AUDIO (L/R)/VIDEO OUTjacks3/4 Channel Selector SwitchDVD COAXIAL DIGITALAUDIO OUT jackRF IN jackCHANNEL  s / t buttonsAUDIO (L/R)/VIDEO IN jacks FF (Fast Forward) buttonRemote sensorEJECT buttonVCR indicatorVCR/DVD mode selector buttonCassette Loading SlotREW (Rewind) button REC buttonDVD indicatorDVD OPTICALDIGITAL AUDIOOUT jackDVD AUDIO (L/R) OUT jacksDVD S-VIDEO OUT jack DVD COMPONENT OUT jacksRF OUT jackDisplay window 2A70101A(06-11) 29/11/2001, 13:478
9No. Display DescriptionVCR mode12345671 2 34765PlaybackStopStill pictureFrame advanced playbackForward slowmotionFast Forward playbackReview playbackSkip chapter to forwarddirectionSkip chapter to reversedirectionOpen or Close the trayAuto resumeDirection button’s markA-B repeatSubtitle languageSoundtrack languageAngleZoomParental level lockedParental level unlockedScreen size: Normal TVScreen size: PAN SCANScreen size: WIDEShows Prohibited actABExplanation for On-Screen-Symbol:Display891011VCRDVDCDPM10 : 0001 : 002C036LTRKRECCH02Playback (lights) / Auto resume (flashes)Still pictureDVD disc is inserted.CD is inserted.Display for afternoon (lights out in the morning)Clock display (colon[ : ] flashes)Counter display by hour/minute at VCR/DVD / by minute/second at CDTrack number display for CDTV channel display for VCRCATV channel displayExternal input displayTimer recording displayVideo tape is in the unitTrack display for CDNormal recording display (flashes during One-touch Timer Recording - OTR)Note:Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.891011Display window 2A70101A(06-11) 29/11/2001, 13:479
10POWER Power on/off 18EJECT Eject a cassette tape 22OPEN/CLOSE Open or Close the tray 35VCR/DVD Switch to operate VCR or DVD 18,380-9 Direct channel selection of TV 21,26Input setting 39Enter a password 43DISPLAY/CALL Display VCR or DVD operation status 27,54INPUT SELECT Switch the connected TV to external mode 32CH  /Select channel of the connected TV or VCR26,28  /  Cursor buttons 34TRACKING/SET –/+Setting buttons 29,30Manual tracking buttons in playback mode 24    / Cursor buttons 18SELECT/ENTER Enter information in the menu 18Select option in the menu 34DVD MENU Select menu of a DVD disc 42SET UP/VCR MENUDisplay menu of setup 18,34,43-53CLEAR/CANCEL Delete Timer program 30Cancel input data in the setting mode 19,29,37,39RETURN Remove DVD set up menu 34ZOOM Zoom (for DVD playback) 37TITLE Select title of a DVD disc 42REPEAT A-BRepeat playback between A and B (DVD/CD)38AUDIO/AUDIO SELECTSwitches sound between mono, stereo and SAP31Change sound track language of DVD 41MEMORY Arrange the order of titles, chapters or tracks 39ZERO RETURNStop the tape when the counter reaches 00:0025ANGLE Change playback angle of a DVD disc 42COUNTER RESETReset the counter to 00:00 25CLOCK/COUNTERChange the front Display mode 25TIMER RECSet the unit to start recording at a preset time.29,30SUB TITLE Set Subtitle of a DVD disc 41ATR Digital AUTO TRACKING 24PLAY MODE Select playback mode 38,39SPEED Sets the tape speed for recording 26,28TV/VCR Switches between TV and VCR 18,27REW/SEARCH Rewind/Review playback 23,24,36PLAY Playback 23,35F.FWD/SEARCHFast Forward/Forward search playback23,24,36SKIP  /Skip chapter to forward or reverse direction36INDEX  /Search for the INDEX mark of a tape 25STOP Stop 23,35REC/OTR Recording 26,28,32SLOW Slowmotion playback 24,36PAUSE/STILL Still picture/Recording pause on/off 24,27,32,36EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERRemote controlPage 2A70101A(06-11) 04/12/2001, 23:0610
11Inserting Batteries123Operation•Aim the remote control at the remote sensor and press control buttonsto operate.•Operate the remote control within 30° angle on either side of the remotesensor, up to a distance of Approx. 5 meters.Remote controlReplace the compartmentcover.Install two "AAA" batteries (notsupplied), paying attention to thepolarity diagram in the batterycompartment.Open the batterycompartment cover in thedirection of the arrow.Approx. 5 metersBattery precautionsThe precautions below should be followed when using batteries in this device:1.Use only the size and type of batteries specified.2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.Reversed batteries may cause damage to the device.  To avoid a potential short circuit, insert the “–” end first.3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury frompossible battery leakage.5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow batterymanufacturer’s directions.)•Press POWER to turn the DVD/VCR on or off.•Make sure VCR/DVD switch is set to VCR/DVD.•Tap CH   or CH   to move through the channels one channel at a time.•The CH / and SET +/– are also used to navigate on-screen menu system.•You can directly access specific channels using Number keys pad.•Each press of VCR/DVD on the remote control, switches the screen between the VCR screen (VCR mode)and the DVD screen (DVD mode).Remote control basics 2A70101A(06-11) 29/11/2001, 13:4711
12OUT(TV)IN(ANT.)OUT(TV)IN(ANT.)OUT(TV)IN(ANT.)NOTES: •A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect theantenna to the DVD/VCR properly.•For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use ofan outdoor type antenna is required.•If you are not sure about the connection, please refer to qualified service personnel.If you are using an antenna system, follow the instructions. If you are a cable (CATV) subscriber,skip aheadto page 14 for the proper connections. ANTENNA TO DVD/VCR CONNECTIONThe DVD/VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TVand connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connectingan antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connectiondiagram.If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300ohm inputs and one 75 ohm output.NOTE:Basic connectionsCombination VHF/UHF Antenna with 75 ohm Coaxial CableCombination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) WireSeparate VHF and UHF Antennas123DVD/VCRVHF UHF300 ohm Twin Lead (Flat) WireMatching Transformer 300 ohm Input75 ohm output(not supplied)300 ohm Twin Lead (Flat) Wire75 ohm Coaxial Cable75 ohm Coaxial CableCombiner75/300 ohm Inputs75 ohm output(not supplied)DVD/VCRDVD/VCR 2A70101A(12-15) 29/11/2001, 13:4712
13UHFVHFUHFVHFVHF/UHF INNOTE: If a VHF or UHF antenna isused, set the TV/CATVmenu option to the "TV"mode.NOTE: If a VHF or UHF antenna isused, set the TV/CATVmenu option to the "TV"mode.NOTE: If a VHF or UHF antenna isused, set the TV/CATVmenu option to the "TV"mode.75 ohm Coaxial Cable (supplied)Splitter75 ohm Input75/300 ohm outputs(not supplied)Splitter75 ohm Input300 ohm outputs(not supplied)TV with single 75 ohm VHF/UHFantenna inputTV with 300 ohm UHFand 75 ohm VHFantenna inputsTV with 300 ohm UHF and 300 ohm VHFantenna inputs DVD/VCR TO TV CONNECTIONAfter you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and followthe connection diagram.This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antennainputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.TVTVTV75 ohm Coaxial Cable(supplied)75 ohm Coaxial Cable(supplied)Basic connections 2A70101A(12-15) 29/11/2001, 13:4713
14VHF/UHFIN (ANT)OUT(TV)IN(ANT.)VHF/UHFIN (ANT)OUT(TV)IN(ANT.)VHF/UHFIN (ANT)OUT(TV)IN(ANT.)Many cable companies offer services permitting reception of extra channels including pay or subscription channels.This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cablecompany supplied converter box, except for those channels which are intentionally scrambled. If you subscribe toa special channel which is scrambled, you must have a descrambler box for proper reception.CATV (CABLE TV) connectionsNOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCRto the output of the Converter/Descrambler box, usually channel 3 or 4.ALLOWS: *Recording of nonscrambled channels.*Use of the programmable timer.*Recording of one channel while watching another.ALLOWS: *Recording of channels through the converter box(scrambled and unscrambled).*Using the programmable timer to record only thechannel selected at the converter box.PREVENTS: *Recording one channel while watching another.*Using the DVD/VCR tuner to select channels.12DVD/VCRIncoming CableTVConverter/DescramblerIncomingCableTVIncoming Cable Converter/DescramblerTV3ALLOWS: *Recording of nonscrambled channels.*Use of the programmable timer.*Recording an unscrambled channel while watchingany channel selected at the converter box.PREVENTS: Recording scrambled channels.To record from converter/descrambler,DVD/VCR tuner must be tuned to theconverter output channel, usuallychannel 3 or 4.If you are playing a tape or using thetuner built into the DVD/VCR, theconverter must be set to the videochannel output of the DVD/VCR (either3 or 4).NOTE:NOTE:DVD/VCRDVD/VCR 2A70101A(12-15) 29/11/2001, 13:4714
15VHF/UHFIN (ANT)ABOUT(TV)IN(ANT.)VHF/UHFIN (ANT)ABOUT(TV)IN(ANT.)This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambledprograms, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consultyour local cable company for more information concerning connection to their descrambler equipment. There are manyways to connect your DVD/VCR to a cable system. Below are six common methods of connection.IMPORTANT: Make sure the TV/CATV menu option is set to the "CATV" mode.IncomingCable456ALLOWS: *Recording of one channel while watching another.*Using the programmable timer to record only the channel selected at the converter box.*Recording of all channels through the converter box.PREVENTS: *Watching scrambled channels while recording another channel.*Using the DVD/VCR tuner to select channels.DVD/VCRSplitterConverter/DescramblerTVDVD/VCRConverter/Descrambler A/B SwitchTVIncomingCableSplitterALLOWS: *Recording of nonscrambled channels.*Recording of one channel while watching another.*Watching premium channels through the converter while recording nonscrambled channels.*Using the programmable timer.PREVENTS: Recording scrambled channels.ALLOWS: *Recording of all channels through the converter box.*Recording a scrambled or unscrambled channel while watching another (scrambled orunscrambled) channel.*Using the programmable timer to record only the channel selected at the converter box.PREVENTS: Using the DVD/VCR tuner to select channels.DVD/VCRA/B SwitchSplitter TVIncomingCableConverter/DescramblerConverter/DescramblerA/B SwitchCATV (CABLE TV) connectionsVHF/UHFIN (ANT)ABOUT(TV)IN(ANT.) 2A70101A(12-15) 29/11/2001, 13:4715
163CH.INOUTANT.DIGITAL AUDIO AUDIO S-VIDEO COMPONENTDVD OUTPUTLRVIDEOOPTICAL COAXIALAUDIOLR4(          )TV(       )YPB/CBPR/CR3CH.INOUTANT.DIGITAL AUDIO AUDIO S-VIDEO COMPONENTDVD OUTPUTLRVIDEOOPTICAL COAXIALAUDIOLR4(          )TV(       )YPB/CBPR/CR3CH.INOUTANT.DIGITAL AUDIO AUDIO S-VIDEO COMPONENTDVD OUTPUTLRVIDEOOPTICAL COAXIALAUDIOLR4(          )TV(       )YPB/CBPR/CRPlayback ConnectionTo Audio (R) InputTo Audio (L) InputTo VideoInputAudio (L) OutputAudio (R) OutputVideo OutputDVD/VCRTVAUDIO/VIDEO Cord (supplied)Connect to a TV with Audio/Video OutputUse the supplied AUDIO/VIDEO Cord.Connect to a TV with S-Video OutputDVD/VCRTVS-Video Cord (not supplied)To Audio (R) InputTo S-Video InputTo Audio (L) Input S-Video OutputAUDIO Cord (not supplied)Audio (L) OutputAudio (R) OutputThe exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependenton the model and features of each component. Check the Owner's Manual provided with each component for thelocation of video and audio inputs and outputs.Connect to a BS TUNERAudio (R) OutputAudio (L) OutputVideo OutputDVD/VCRTVAUDIO/VIDEO Cord (supplied)BS TunerSatelliteAntenna To ANT. Input75 ohm Coaxial Cable (not supplied)ANT. InputANT. outputTo ANT.InputANT.Output75 ohm CoaxialCable (supplied)VHF/UHFAntenna 2A70101A(16-19) 29/11/2001, 13:4816
173CH.INOUTANT.DIGITAL AUDIO AUDIO S-VIDEO COMPONENTDVD OUTPUTLRVIDEOOPTICAL COAXIALAUDIOLR4(          )TV(       )YPB/CBPR/CR3CH.INOUTANT.DIGITAL AUDIO AUDIO S-VIDEO COMPONENTDVD OUTPUTLRVIDEOOPTICAL COAXIALAUDIOLR4(          )TV(       )YPB/CBPR/CRConnect to an AV Amplifier with built-in digital surroundIf you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systemssuch as Dolby Digital and DTS by using the Optical or Coaxial Digital Output.Use this connection to connect an:• AV amplifier with built-in *Dolby Digital decoder• AV amplifier with built-in *DTS decoderPlayback connectionConnect to a Stereo Amplifier with Audio OutputNOTES:••••••The OPTICAL, COAXIAL, AUDIO L/R, S-VIDEO and COMPONENT jacks are useful only for DVD section. TheVHS signal is output only from the composite jack (DVD/VCR VIDEO OUTPUT) and UHF/VHF OUT.When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AVAmplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing thespeakers to be damaged.Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital inputconnector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs maycause such a high level of noise that it may be harmful to your ears and damage your speakers.DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder isnecessary.When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.Video cord (not supplied) To VideoInputCoaxial digital cable(not supplied)AV Amplifier withbuilt-in variousdecoder as aboveDVD/VCRTVConnecting the optical digital cableWhen you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.When not using the optical digital cable, attach the dust protection cap to protect against dust.If your TV has COMPONENT VIDEO IN jack, you can connect the DVD/VCR to the TV with a COMPONENT cable(not supplied) as shown below. COMPONENT VIDEO output jack can send high-quality video signal to a TV thanS-Video output.You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digitalcable.NOTE:You may connect to a TV with aComponent video cable(not supplied) orS-Video cable(not supplied) instead ofa video cable(not supplied).To Audio (L) InputToComponentVideo InputTo Audio (R) InputTVAUDIO Cord (not supplied)Stereo AmplifierAUDIO/VIDEO Cord (supplied)DVD/VCRAudio (R) OutputCOMPONENT VIDEO Cord (not supplied)To ComponentVideo OutputAudio (L) OutputCoaxial digitalAudio OutputTo Audio/Video OutputTo Audio/Video InputVideo Output 2A70101A(16-19) 04/12/2001, 23:0617
18EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSetting the Video Channel / Setting the languageTo view playback of a recorded tape,or to watch a program selected bythe VCR's channel selector, the TVmust be set to channel 3 or 4 (videochannel).NOTES:•If the unit does not operateproperly, or No key operation (bythe unit and/or the remote control):Static electricity, etc., may affect theplayer's operation. Disconnect the ACpower cord once, then connect itagain.•The VCR section has its own menuand also DVD section has its ownmenu (see page 34).•If there is no pressing of any buttonsfor more than 60 seconds, then theMENU screen back to TV-operationautomatically.1Press POWER to turn on the DVD/VCR.2Press VCR/DVD to select the VCR mode. The VCR indicatoron the front panel will light.You can choose from three different languages (English,French and Spanish) for the on-screen displays.When a TV is connected with the 75 ohm coaxial cable only.3Set the 3/4 Channel selector switch on the rear panel to CH3 or 4.4Turn ON the TV and set to CH 3 or 4 to correspond with thechannel selected in step 3.5Press TV/VCR to select the VCR position.The VCR indicator will appear in the display.6Select any channel to receive a TV station in your area.The channel number will appear on the screen for about4 seconds.For a push-button TV tunerIf CH 3 or 4 corresponding to the video channel cannot be tunedon your TV, proceed as follows: set the VCR 3/4 channel selectorand the TV to CH 3 or 4, play back a prerecorded tape and tunethe TV to receive a sharp color picture from the video cassetterecorder. Refer to your TV owner's manual for details.Setting the Video ChannelSetting the language3Press VCR MENU,If you use the unit for the first timeand press VCR MENU, instead ofthe main menu screen on the rightthe SYSTEM SET UP menuscreen in step 2 may appear.Press   or   to select the desiredlanguage: English (ENGLISH),Spanish (ESPAÑOL) or French(FRANCAIS), then press ENTER.12Press   or   to select the“LANGUAGE” option, then pressENTER.4Press VCR MENU until the MENU screen is cleared.⟨+/-/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SET UPSYSTEM SET UP⟨+/-/ENTER/MENU⟩SYSTEM SET UPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDON OFF 2A70101A(16-19) 04/12/2001, 23:0618
194Clock settingYou must set the date and time fortimer recordings.Press   or   to set the month,then press ENTER.23Press   or   to select the“CLOCK SET” option, then pressENTER.After a power failure or disconnectionof the power, the timer settings will belost. In this case, reset the present time.NOTE:1Press VCR MENU. The VCR menu screen will appear.5Set the day, year and time as instep 4.6After setting the clock, date andtime starts functioningautomatically.To make corrections any time during the processPress CANCEL repeatedly until the item you want to changeblinks, then press   or  .Turn ON the TV and set to the video input mode.Press VCR/DVD to select the VCR mode. (The VCR indicatorwill light)Preparation:••⟨+/—/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SET UPSYSTEM SET UP⟨+/—/ENTER/MENU⟩SYSTEM SET UPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDON OFFEXAMPLE: Setting the clock to "8:30 AM" March, 23 (SAT), 2002.⟨+/—/ENTER/CANCEL/MENU⟩MONTHDAYYEARTIME31 (WED)200012 : 00AM⟨+/—/ENTER/CANCEL/MENU⟩MONTHDAYYEARTIME323 (SAT)20028 : 30AM8 : 30AM   SATEJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERPress   or   to select the“SYSTEM SET UP” menu, thenpress  ENTER. 2A70101A(16-19) 04/12/2001, 23:0619
203Tuner settingThis DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down tothe next channel set into memory, skipping over unwanted channels. Before selecting channels, theymust be programmed into the DVD/VCR’s memory. In addition to normal VHF and UHF channels, this DVD/VCR can receive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CATVmenu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.Press VCR MENU. The VCR menu screen will appear. Press or   to select “CH SET UP”, then press ENTER.Then press ENTER to select theTV or CATV mode. The arrowindicates the selected mode.12Press   or   to select the “TV/CATV” option.4Press VCR MENU until the menu screen is cleared.TV      - VHF/UHF channelsCATV - CABLE TV channels2Setting channels automaticallyThe VCR can receive a maximum of 181 channels bypresetting the channels into memory.Then press ENTER.The auto tuning will start. Thechannel display will count up andwhen finished, the screen returnsto normal.1Repeat above step 1 and press or   to select “AUTO CHMEMORY”.TV/CATV selectionTurn ON the TV and set to the video input mode.Press VCR/DVD to select the VCR mode. (The VCR indicatorwill light)Preparation:••⟨+/—/ENTER/MENU⟩CH SET UPTV     CATVAUTO CH MEMORYADD/DELETE⟨+/—/ENTER/MENU⟩CH SET UPTV     CATVAUTO CH MEMORYADD/DELETE⟨+/—/ENTER/MENU⟩CH SET UPTV     CATVAUTO CH MEMORYADD/DELETECH 002EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR•You can’t select “CH SET UP” if youset the channel to “L”.NOTE: 2A70101A(20-25) 04/12/2001, 23:0620
212To ADD/DELETE channels / Noise eliminationTo ADD/DELETE channelsRepeat the step 1 on page 20.Then press   or   to select the“ADD/DELETE” option and pressENTER.Press Number keys or  /to select a channel numberyou want to add or delete.1To Add or Delete desired channels1To add channelsPress ENTER until “ADD”appears on the screen to setto add the unmemorizedchannel.To delete channelsPress ENTER until “DELETE” appears on the screen toset to delete the channel from memory. The channelnumber will blink.Repeat       to       to add or delete other channel.12323Press VCR MENU until the menu screen is cleared.Repeat the steps 1~2 on page 19 and press   or   to selectNO NOISE BACKGROUND.12Press ENTER to select the “ON”position.Noise eliminationYou can add the channels you wantor delete the channels you do notwant manually.When you don't want to receive a weak signal broadcast, theBlue back screen can be obtained by selecting the NO NOISEBACKGROUND "ON". When the unit is shipped from thefactory, the NO NOISE BACKGROUND is set to the "ON".3Press VCR MENU until the menu screen is cleared.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the VCR mode. (The VCR indicatorwill light)Preparation:••⟨+/—/ENTER/MENU⟩CH SET UPTV     CATVAUTO CH MEMORYADD/DELETE⟨+/—/0—9/ENTER/MENU⟩ADD CH  003⟨+/-/ENTER/MENU⟩SYSTEM SET UPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDON OFFEJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTER 2A70101A(20-25) 04/12/2001, 23:0621
22Tape speed and maximum recording timeVideo cassette tapeTape SpeedSLP (Super Long Play)Loading and Unloading a cassette tapeTo prevent accidental erasureRemove the erase prevention tab with a screwdriver. Cover the hole with a piece of adhesive tape.To record againErase prevention tabScrewdriverAdhesive tapeAutomatic tape ejectThis VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to itsbeginning, the cassette tape will be ejected automatically.Press EJECT on the unit or the Remote. Remove the cassette tape.LoadingPush the center of the tape until it is automaticallyinserted.Insert the cassette tape with its labeled side facing upand the erase prevention tab positioned at your left.An inverted cassette tape cannot be inserted.Erase prevention tabAutomatic playbackWhen loading a cassette tape without an erase prevention tab, playback will start automatically.Automatic power ONWhen you insert a cassette tape the VCR power will turn ON automatically.Unloading12Use only video cassette tapes marked  .T-160 T-120 T-90 T-60 T-302-2/3 hours 2 hours 1-1/2 hours 1 hour 30 minutes8 hours 6 hours 4-1/2 hours 3 hours 1-1/2 hoursSP (Standard Play)VCR 2A70101A(20-25) 04/12/2001, 23:0622
23Cassette tape playbackLoad a prerecorded tape(When loading a cassette tapewithout the erase preventiontab, playback will start auto-matically).12Press PLAY.Playback will start."   " will appear on the screenfor about 4 seconds.To start playbackPress STOP once.The tape will stop but remainfully loaded and ready to play."   " will appear on the screenfor about 4 seconds.To stop playbackTo rewind the tape or forward it rapidlyStop the playback or recording with STOP.To rewind the tape:Press REW.To forward the tape:Press F.FWD.To stop the tape-winding, press STOP. To switch to playbackdirectly (without STOP), press PLAY.Forward/Reverse picture search modeWhen the tape is being winded, you can switch to picture searchmode (see next page). To do this, press REW or F.FWD and holdit down. The unit will resume the tape winding as soon as thebutton is released.•This VCR selects the playback tapespeed SP, LP or SLP automatically.•The Cassette tape and DVD disc canbe played back simultaneously. If youpress VCR/DVD, the tape playbackand DVD playback alternate with eachother on the screen.•When you select the VCR mode duringDVD playback DVD playback will stopautomatically after approx. 5 minutes.NOTES:Turn ON the TV and set to the video input mode.Press VCR/DVD to select the VCR mode. (The VCR indicatorwill light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERMEMORY/ZERO RETURNPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTR123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(20-25) 04/12/2001, 23:0623
24Adjusting tracking conditionSpecial playbackReverse picture search functionPress REW x 1 or x 2 during the playback.Picture SearchForward picture search functionPress F.FWD x 1 or x 2 during the playback.To return to playback: Press PLAY.Still PicturePress PAUSE during playback. To resume normalplayback: Press PLAY.Slow MotionDuring playback press SLOW.To return to playback: Press PLAY or SLOW.Whenever you insert a tape and start playback,automatic tracking starts working and continuouslyanalyzes the signal to enable optimum picture qualityduring playback.Press PAUSE during playback.Press SLOW one by one: The picture advances frameby frame.To return to playback: Press PLAY or PAUSE.Frame by Frame pictureNOTES:•The audio output is muted during SPEED SEARCH,STILL, FRAME ADVANCE and SLOW MOTION.•During picture search mode there will be noise barswhich are caused by the system.•These Special Playback will automatically changeto playback after approx. 5 minutes to protect thevideo tape against excessive wear.Slow tracking and vertical lock adjustmentIf noise bars appear in the picture during slow motion,press the TRACKING + or – to reduce the noise bars.If the still picture jitters excessively, press TRACKING+ or – to stabilize the still picture.Automatic tracking adjustmentIf automatic tracking cannot eliminate noises well duringplayback, press TRACKING +/– to eliminate the noises.“MANUAL TR.” will appear. Press it briefly for a fineadjustment, or press and hold for a coarse adjustment.Manual tracking adjustmentRepeat playbackThe whole of the video tape will be played until its end.Then the tape will be winded until its beginning and theplayback will be repeated.1Press SETUP MENU. Press   or   to selectAUTO REPEAT.3Press VCR MENU until the menu screen iscleared.if you press CALL, "" will appear on the screen.Then press ENTER toselect [ON] or [OFF].If [ON] is selected, theplayback will berepeated endlessly.4To start the playback, press PLAY.The playback will be repeated endlessly.2To cancel repeat mode:Follow the above step 1, then press ENTER to selectthe OFF position. Press VCR MENU to return to theTV.Press ATR to reactivate automatic tracking again.“AUTO TR.” will appear.•⟨+/—/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SET UPSYSTEM SET UPPICTURE SEARCH SPEEDPRESS TWICETAPE SPEED PRESS ONCESP (Standard Play)LP (Long Play)SLP (Super Long Play)5 X9 X15 X3 X7 X9 XSPEED SEARCH TIMES 2A70101A(20-25) 04/12/2001, 23:0624
25123CHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMDISPLAY/CALLINPUT SELECTTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWD4560789TIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURNSELECT/ENTER+3Press CALL.The counter display shows the taperunning time during playback orrecording.ZERO RETURN function / Video index search systemZERO RETURN functionThis function makes tape-rewindingstop at the counter 00:00:00 positionautomatically.NOTES for Counter Display:If you rewind the tape from “00:00:00”,a minus sign (“–”) will be displayed infront of the time.When you load a tape, the counter willreset to “00:00:00”.The counter does not function onnonrecorded (blank) sections of thetape. When you rewind, fast forward orplay tapes through blank sections, thecounter stops.•••Press COUNTER RESET at the desiredtape position. The counter display will bereset to the "00:00:00" position (e.g. thebegining of recording).2Press STOP when playback or recording is finished.Press ZERO RETURN.The tape will be rewinded or fast forwarded and automaticallystop at the ”00:00:00” position.The CLOCK/COUNTER-buttonPress CLOCK/COUNTER. The clock and tapecounter alternate with each other in the display.13Video index search systemThis function enables you to locate the beginning of anyrecording made on the VCR.Recording an INDEX MARKThe Index Search function automaticallyrecords an INDEX mark on the tapewhenever a recording is initiated.INDEX NO. (up to 9)or      is displayedIndex SearchPress INDEX      or      during stop or playmode.For Succeeding programs: Press INDEX      .For Preceding programs: Press INDEX      .(Additional press increases the INDEX NO.up to 9.)The INDEX      or      is pressed, the unitstarts searching the INDEX NO. selectedand finds the portion, then playback startsautomatically.To stop the Index Search, press STOP.NOTES for Video index search system:When you recorded an INDEX mark atthe very beginning of the tape, themark may not be found.During INDEX search, the tape maystop and begin to play at a slightlydifferent location.INDEX may not function properly withold or worn out video tapes.INDEX mark may not be found if it isextremely close to the point where thesearch began.In recording, if you stop recordingtemporarily, the INDEX mark is notrecorded on the tape.•••••Turn ON the TV and set to the video input mode.Press VCR/DVD to select the VCR mode. (The VCR indicatorwill light)Preparation:••CH  0018 : 47AM   MON00 : 04 : 38  SPSTEREO  SAPCH  0018 : 47AM   MON00 : 00 : 00  SPSTEREO  SAPVCRVCRVCRVCRCH  001INDEX 2A70101A(20-25) 04/12/2001, 23:0625
26EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR3Recording a TV programLoad a cassette tape with the eraseprevention tab intact.The VCR will automatically turn on.Set the TV/CATV option to the appropriate position (See page20).12Press SPEED to select the desired tapespeed SP or SLP.The tape counter and SP or SLP willappear on the screen for about 4seconds.4TV      - VHF/UHF channelsCATV - CABLE TV channelsRecording and viewing thesame TV programPress Number keys or CH  /  to select the channel to berecorded.VHF/UHF/CATV CHANNELSTV CATVVHF2-13UHF14-69VHF2-13STD/HRC/IRC 14-36   (A) (W) 37-59  (AA) (WW)    60-85   (AAA) (ZZZ)  86-94   (86) (94) 95-99   (A-5) (A-1)100-125  (100)(125)  01  (5A)5Press REC/OTR."   " will appear on the screen forabout 4 seconds and “REC” willappear on the display.NOTES:•If the erase prevention tab is removed,the tape will eject when REC/OTR ispressed for recording.•If you wish to watch the DVD playbackduring the normal recording on VCR,press  VCR/DVD to change to DVDmode and perform the DVD playback(see page 35).•You can not record disc material inDVD, Video CD, Audio CD, etc. onto avideo tape with this DVD/VCR.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the VCR mode. (The VCR indicatorwill light)Preparation:••00 : 00 : 00  SPCH  110CH  110INDEX1-9 Press 0 twice and then 1-9 as required. Example: Toselect 2, Press “002”.10-12 Press 0 first and then the remaining 2 digits in orderfrom left to right.Example: Press 012 for “12”.13-99 Press 2 digits in order.Example: Press 22 for “22”.100-125 Press the 3 digits in order.Example: Press 110 for “110”. 2A70101A(26-31) 04/12/2001, 23:0726
27EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERCH  1258 : 30AM   MON00 : 00 : 00  SPHI-FICH  1258 : 47AM   MON00 : 00 : 00  SPSTEREO  SAPRecording a TV programPress STOP to stop recording."   " will appear on screen for about 4seconds.To stop recordingPress PAUSE/STILL to avoid recordingunwanted material. Press again to continuethe recording."" will appear on screen for about 4seconds.To stop recording temporarilyNOTES:The pause function will be released after 5 minutes to prevent damageto the tape or the VCR. The VCR will change to the STOP mode.You can select a recording channel in the recording pause mode.••Auto Rewind featureThis VCR will automatically rewind thetape when the tape has ended (exceptduring OTR and TIMER REC). It willalso eject the tape.While the VCR is recording, press TV/VCR to select the TV position.The “VCR” will go off and recording will continue.Select the TV channel you want to watch by using the TV channelselector.Recording one program while watching anotherNOTE:Some CATV hookups do not permit viewing one channel whilerecording another. See pages 14,15.To Display VCR operation StatusPress CALL. The clock, day of the week and more informations willbe indicated.To cancel the indicating: Press CALL until all indicator disappear.While watching TVDAY OF THE WEEKCHANNELTAPE SPEEDREAL TIME COUNTERCLOCKSTEREO ANDSEPARATE AUDIOPROGRAM (SAP)While operating a tapeOPERATINGMODETAPE INAUTO REPEATHI-FI STEREO 2A70101A(26-31) 04/12/2001, 23:0727
283One-touch Timer Recording (OTR)Load a cassette tape with the eraseprevention tab intact.The VCR will automatically turn on.Set the TV/CATV option to the appropriate position (See page20).12Press SPEED to select the desired tapespeed SP or SLP.The tape counter and SP or SLP willappear on the screen for about 4seconds.4TV      - VHF/UHF channelsCATV - CABLE TV channelsThe One-touch Timer Recordingfeature provides a simple andconvenient way to make a timedrecording.Press Number keys or CH  / toselect the channel to be recorded.5NOTE:If you wish to watch the DVD playbackduring the OTR, press DVD/VCR tochange to DVD mode and perform theDVD playback (see page 35).Example: One-touch Timer Recording for 30 minutes.Press REC/OTR. Press the button again to stop recording after30 minutes. Each additional press of REC/OTR will increaserecording time as shown in the chart below, up to a maximum of5 hours. The OTR and recording time will appear on the screenfor about 4 seconds. And, REC will keep blinking in the display.Press STOP or turn off the power."   " will appear on screen for about 4seconds.To cancel OTRPressoncetwice3 times4 times5 timesNORMAL REC0:301:001:302:003:004:005:00NORMAL RECRecording time Press6 times7 times8 times9 timesRecording timeTurn ON the TV and set to the video input mode.Press VCR/DVD to select the VCR mode. (The VCR indicatorwill light)Preparation:••00 : 00 : 00  SPCH  110CH  125INDEXOTR  0 : 30EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(26-31) 04/12/2001, 23:0728
293Timer RecordingPress VCR MENU. Check the TIMERREC SET option is selected, thenpress ENTER.Press SET + or – to select the date,then press ENTER.12Press SET + or – to select one of theprogram line, then press ENTER.4Press VCR/DVD to select the VCR mode.Load a cassette tape with the erase prevention tab intact.Make sure with CALL that the time and date are correct.(seepage 27).Preparation:••Timer recording can be programmedon-screen with the remote control.The built-in timer allows automaticunattended recording of up to 8programs within 1 month.Set the start time, end time, channeland tape speed as in step 3.Example: Program a timer recording for the 26th day, channel 125(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: SLP).NOTES:Press CANCEL to move cursor backwardfor correction.To record from external source set thechannel to "L". "L" will appear next to CH125 (or 69).••5To enter other programs, repeat step2 through 4.• To return to the normal screen,press VCR MENU twice.6Press TIMER REC. The clock symbol( ) will appear on thedisplay and the VCR stands by for recording. At the sametime, VCR mode will change to DVD mode automatically. Youcan use DVD even if the VCR is in the Timer recording mode.If you do not use the DVD, turn the power off.The timer recording will start at 20 seconds bofore the timeyou predetermined.NOTES:If the clock symbol(   ) does not appear on the display in spiteof the pressing of TIMER REC, the cassette may not have beenloaded yet.(see page 22)If the cassette is ejected in spite of the pressing of TIMER REC,the erase prevention tab of the cassette may have beenremoved.(see page 22)••NOTES:If the clock symbol( ) blinks when thetimer recording ended, the TV programhas not been completely recordedbecause of an insufficient tape supply.Press TIMER REC to cancel the timerprogram or press EJECT to removethe cassette tape.During timer recording standby mode,the VCR mode can not be selected. Touse the VCR, press TIMER REC atfirst, then press VCR/DVD to changeto VCR mode. After you use the VCR,press TIMER REC again to put the VCRinto timer recording standby mode.If you press TIMER REC during timerrecording, the recording operation willbe interrupted. If you press TIMERREC again within the programmed time,the recording operation will start again.After a power failure or disconnectionof the power plug, all programmedrecording setting and time display willbe lost upon resumption of power. Inthis case, reset the clock (see page19) and reprogram any timerrecordings.••••⟨+/—/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SET UPSYSTEM SET UP⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ———————————⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————— 26(SU)⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————26(SU)11:00PM11:30PM125SLP⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————26(SU)11:00PM11:30PM125SLPCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRZOOMTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BTIMER REC SUB TITLE/ATRSELECT/ENTERMEMORY/ZERO RETURN123EJECTOPEN/CLOSEVCR/DVDDISPLAY/CALLINPUT SELECT456POWER 2A70101A(26-31) 04/12/2001, 23:0729
30Timer-RecordingTimer Recording Special caseWeekly (e.g. WKL-TU: each Tuesday) or daily (e.g.MO-SA: Monday to Saturday) Timer recordingFollow the procedure of timer recording on the previouspage. At picture 3 press SET + or – repeatedly until thedesired setting appears. Then press ENTER.When you press SET – repeatedly, the indicator atDATE will change as follows, in case today is Friday.In case of Timer progarms-overlappingDo not overlap timer programs as portions of theconflicting programs will be lost. The first recordingtime has priority over the next recording time as shownin the diagram below.•NOTES:The daily/weekly recording can be made continu-ously until the recording is canceled or the tapereaches the end.During timer recording the automatic rewindingmechanism does not function.••Confirmation / Cancellation of the TimerRecording1If the Timer has been activated, now press TIMERREC to deactivate the Timer. The clock symbol( )will disappear. Then press VCR/DVD to change toVCR mode.2At picture 1 on theprevious page selectTIMER REC SET optionand press ENTER.Then the timer programlist as right will appear onthe screen.To cancel Timer program:4Press VCR MENU repeatedly until the TV-pictureappears.3The current day (Friday) SU-SA (Sunday to Saturday)MO-SA (Monday to Saturday)MO-FR (Monday to Friday)WKL-WE WKL-TH (Weekly Thursday)(Weekly Wednesday)One month laterminus one day8 : 00 11 : 009 : 00 10 : 00Program 1Prog.1Deleted PartsNon Recorded Portion PartsProg.2 Prog.3Program 2Program 3Recording Control SettingsPress  SET + or – toselect the unnecessaryprogram, then pressCANCEL to cancel theprogram.To confirm Timer program:NOTES:•If there are other timed record programs remaining,TIMER REC must be pressed to reactivate the timer,otherwise the remaining timer record programs will beignored.•You can not confirm the Timer program during timerrecording operation.•You can correct or cancel the programmed setting inprogram confirm mode.⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————— WKL-WE⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ———————————⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————26(SU)11:00PM11:30PM125SLP 2A70101A(26-31) 29/11/2001, 13:4930
31Stereo recording and playback / Separate Audio Program (SAP)When a MTS STEREO broadcast isreceived, the STEREO will appear onthe screen and the program can beviewed or recorded in stereo.The Hi-Fi STEREO recording procedureis the same as for normal recordings.The VHS Hi-Fi audio system permits highfidelity recording of MTS STEREO TVbroadcasts.NOTES:When playing back a tape that is notrecorded in Hi-Fi stereo mode, theaudio will automatically be monaural.When listening to a VHS Hi-Fi videotape or MTS broadcast through theVHF/UHF jack (Audio/Video cord notconnected), the sound will bemonaural.Stereo recording andplaybackNOTE:When using a CATV system, stereo TV programs may be transmittedover a mono cable channel. In this case the word "STEREO" will notappear and the sound will be in mono.When viewing an MTS STEREO TV program, or playing a prerecordedVHS Hi-Fi STEREO videotape, press AUDIO SELECT to select howthe audio will be heard through the speakers. Normally set to the Hi-FiSTEREO position, this button can be set to the MONO position if thestereo broadcast or videotape audio is of poor quality. The "R" and "L"positions allow the audio from the Right or Left Hi-Fi channel to be heardover both TV speakers. This button has no effect when viewing a MONOvideotape or TV program. Each time when you press the button, OUTPUTSELECTION display appears on the screen for several seconds. Referto the chart below.Output selectionOUTPUTSELECTIONSTEREOL CHR CHMONOSOUND HEARD ON BOTHSPEAKERSSTEREOLEFT CHANNEL AUDIORIGHT CHANNEL AUDIOMONOYour VCR is fitted with an SAP broadcast system which enablesyou to switch to a separate audio program when viewing aselected channel.This function applies only when the program is broadcast inmulti-languages through the SAP broadcast system.Separate Audio Program (SAP)Press VCR MENU. Then press   or   to select "SAP".12Then press ENTER to select [ON].Then press VCR MENU until themenu screen is cleared.When the VCR is turned on or a channel selection is made, makecertain "SAP" appears on the screen. This means that the "SeparateAudio Program" broadcasting is available.Listening to SAPOR••STEREOSTEREO  SAPSAP⟨+/—/ENTER/MENU⟩MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SET UPSYSTEM SET UPEJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTER 2A70101A(26-31) 04/12/2001, 23:0731
32If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.Make all connections before turning on the power.Duplicating a video tape/Duplicating a disc material onto a video tapeLoad a blank cassette tape with the erase preven-tion tab intact into the recording VCR.Load a previously recorded tape into the playbackVCR or CAMCORDER.1Press SPEED to select the desired tape speed SPor SLP.It is recommended that you set the Speed to theSP mode on the recording VCR for best results.2Press  INPUT SELECT to select AUDIO/VIDEOinput position. "L" will appear inthe display.3Press REC/OTR on the recording VCR, then pressPAUSE/STILL.4Press PLAY button on the playback VCR orCAMCORDER, then press PAUSE/STILL button.5Press PAUSE/STILL on both the VCRssimultaneously to begin the duplicating process.6For duplicating a previously recorded tape from acamcorder, follow the camcorder manufacturer’sinstructions. A typical camcorder dubbing hookupis shown above.To AUDIO (L) INTo AUDIO (L) OUTAUDIO/VIDEO Cord (supplied)Playback VCRTo VIDEO OUT To AUDIO (R) OUTRecording VCRTo VIDEO IN To AUDIO (R) INAUDIO/VIDEO Cord (not supplied)To AUDIO (R) INTo AUDIO (L) INTo VIDEO INRecording VCRTo AV JackPlayback CamcorderConnection with second Video recorder Connection with Video cameraDuplicating a video tape 2A70101A(32-37) 29/11/2001, 13:4932
33DiscThis unit applies to DVD discs from Region 1 only.The loaded Disc (DVD, Audio-CD and MP3-CD) will be recognized automatically.The suitable Disc-format are: DVD, CD-R and CD-RW.Do not play DVD-ROM, DVD-Audio, CDV, Video-CD, CD-G or Photo CD to prevent accidental erasure of prerecordedmaterial.Some DVDs is played back with a Copy guard system. In case of a dubbing on video tape, strong disturbance mayoccur. This is not a defect of this DVD/VCR.TitleWhen two or more movies are recorded on a disc,the disc is divided into two or more sections. Eachsection is called a “TITLE”.ChapterThe titles can be subdivided into many sections.Each section is called a “CHAPTER”.TrackAn Audio CD can contain several items.These are assigned to the tracks.Removing Disc from CaseBe sure to hold the edge of disc. Do not touch the surface of the disc.Pick up the disc gently from the case.• Do not scratch the disc.• Do not get dirt on the surface of the disc.• Do not stick a label or adhesive tape on the disc.• Do not drop or bend the disc.Storing Disc• Store the disc in the case to avoid risk of scratches, dirt or damage.• Do not leave disc exposed to direct sunlight or in hot or humid places.Cleaning DiscWipe the disc with a clean, dry cloth from centre to edge.• Do not wipe the disc round.• Do not use liquid or aerosol cleaners.CHAPTER 1TITLE1 TITLE2DVD DISCCHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1TRACK  1 TRACK  2 TRACK  3 TRACK  4 TRACK  5CDAudio-CD 2A70101A(32-37) 29/11/2001, 13:4933
34EnglishEspa olFran aisABCLanguageSubtitle Language ENGAudio Language ENGDsc Menu Language ENGOn-Screen Language ENG: Select : EnterABCLanguageSubtitle Language ENGAudio Language ENGDisc Menu Language ENGOn-Screen Language ENG: Select : Enter4Setting setup languageThe setup language can be selected.Press  / to select desiredlanguage (e.g. English), thenpress  ENTER.2Press SET UP  in the stop mode.The SETUP MENU of DVD willappear on the screen.NOTE: To make SETUP screen disappear, press SETUP (orRETURN).If the DVD/VCR does not operateproperly: Static electricity, etc., mayaffect the player's operation. Disconnectthe AC power cord once, then connectit again.3Press  / to select On-screenLanguage, then press  ENTER.Then press   or   to select“Language”.ABCPictureTV Shape 4:3LB: Select : Enter1Press  VCR/DVD to select theDVD mode. (The DVD indicatorwill light)“No Disc” will appear on thescreen. (If DVD disc has alreadyloaded, the playback will startautomatically.)Turn ON the TV and set to the video input mode.When using an amplifier, switch on the amplifier.Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(32-37) 04/12/2001, 23:0734
354Playback procedurePress PLAY or OPEN/CLOSE.The disc tray closes automati-cally.On the screen,   change to“” and then playback willcommence.•A menu screen may appear onthe TV screen, if the disc hasa menu feature. In this case,press  ,  ,  ,   orENTER to operate a menufeature.1Press OPEN/CLOSE.The disc tray will open.2Place a disc onto the tray.Hold the disc, position it with theprinted label side up, align it withthe guides, and place it in itsproper position.3Press STOP to end playback.•The DVD/VCR memorizes the stopped point, depending onthe disc. “To Return To The Last Scene Viewed, Press Play.To Disable  This Operation, Press STOP Again.” appears onthe screen for approx. 4 seconds. “” keep blinking in thedisplay until the playback is stopped completely. Press PLAYto resume playback (from the scene point).•If you press STOP again (“   ” appears on the screen) orunload the disc, the DVD/VCR will clear the stopped point.5Then press OPEN/CLOSE.The disc tray opens.Remove the disc and press POWER.The disc tray closes automatically and DVD/VCR turns off.NOTES:•If a non-compatible disc is loaded, "Please Check Disc", "Disc playback unauthorized Consult owners manualfor further information" or "Parental Lock" will appear on the TV screen according to the type of loaded disc. Inthis case, check your disc again (See pages 33 and 43).•Some discs may take a minute or so to start playback.•A “Prohibition” symbol may appear at the upper right of the screen. This symbol means either the feature youtried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicatea problem with the DVD/VCR.•When you set a single-faced disc label downwards (ie. the wrong way up) and press PLAY or OPEN/CLOSE,"" will appear and remain on the screen for approx. 40 seconds and then it will change to "Please Check Disc".•Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR playsDVDs according to the disc contents the software producers designed, some playback features may not beavailable. Also refer to the instructions supplied with the DVDs.•When playing DTS-encoded Audio CDs, excessive noise will be heard from the analogue stereo outputs. Toavoid possible damage to the audio system, the consumer should take proper precautions when the analoguestereo outputs of the DVD/VCR are connected to an amplification system.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(32-37) 04/12/2001, 23:0735
36Special playbackPress F.FWD during normal playback.Each press of F.FWD will increase the speed of the search x2, x8,x30, x100. (in case of Audio-CD: x4 and x8 are available)• To resume normal playback, press PLAY.Fast Forward PlaybackPress REW normal playback.Each press of REW will increase the speed of the search x2, x8, x30,x100. (in case of Audio-CD: x4 and x8 are available)• To resume normal playback, press PLAY.Review PlaybackPress PAUSE/STILL during normalplayback.Still PlaybackTo resume normal playback, pressPLAY.Press PAUSE/STILL during still play-back.One frame is advanced each timeyou press PAUSE/STILL.Frame Advance• To resume normal playback, press PLAY.• To resume the still playback, press PAUSE/STILL.Press SLOW during normal playback or still playback.Each press of SLOW will change the speed of the slow x1/2, x1/4,x1/8.Slow-motion PlaybackTo resume normal playback, pressPLAY.Locating a chapter or trackThe unit is capable of holding a still videoimage or On screen display image on yourtelevision screen indefinitely.  If you leavethe still video image or On screen displayimage displayed on your TV for an ex-tended period of time, you risk permanentdamage to your television screen.  Pro-jection televisions are very susceptible.Press SKIP ( ) Forward or SKIP ( ) Reverse during play-back to locate a chapter that you want to watch.Each time you press the button, a chapter or track is skipped.NOTE:Note: there may be a slight delay be-tween you pressing the button and thefunction activating.EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(32-37) 04/12/2001, 23:0736
37Press ZOOM during playback.The center part of the image willbe zoomed in.As you repeatedly press theENTER or ZOOM button while“ZOOM” is selected, the magnifi-cation level changes. Variation ofthe levels includes imagereduction.• If you want to return to a 1:1 view, select “EXIT” and pressENTER.: Select : ChangeZoom OffZOOMEXITThis unit will allow you to zoom in on the frame image. You canthen make selections by switching the position of the frame.While “ZOOM” is selected, press ZOOM repeatedly to return toa 1:1 view.123ZoomingPress  /  or  / to view a different part of the frame.You may move the frame from the center position to UP,DOWN, LEFT or RIGHT direction.• Press CLEAR to restore the zoom point to the center of thepicture.ZoomingTurn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(32-37) 04/12/2001, 23:0737
38A-NOTES:Some discs may not work with therepeat operation.In A-B repeat mode, subtitles nearpoint A or B may not appear.During the A-B Repeat Playback theANGLE feature will not operate.You may not be able to set A-B Re-peat, depending on the scenes of theDVD.A-B repeat does not work with an in-teractive DVD and MP3-CD.Random playback can not be com-bined with Repeat playback.Repeat playbackTitle, Chapter, Track, Random Playback••••••2During play repeat playback will start automatically.During stop mode press PLAY within about 5 seconds afteryou press the PLAY MODE button to start repeat playback.•To resume normal playback, select Off.REPEAT PLAYBACKTurn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERA-B repeat playback allows you to repeat material between twoselected points.1Press  REPEAT A-B duringplayback.The start point is selected.2Press REPEAT A-B again.The end point is selected.Playback starts at the point thatyou selected. Playback stops atthe end point, returns to Point Aautomatically, then starts again.A-B Repeat PlaybackTo resume normal playbackpress REPEAT A-B again.“Repeat Off” appears on the screen.A-BTrack Repeat1Press PLAY MODE repeatedly to select “Chapter Repeat”,“Title Repeat” or “ALL”. (In case of CD, select “Track Repeat”or “ ALL Repeat” )CDREPEAT PLAYBACKChapter RepeatDVD 2A70101A(38-43) 04/12/2001, 23:0738
391 T:- -CT:- - -2 T:- -CT:- - -3 T:- -CT:- - -4 T:- -CT:- - -5 T:- -CT:- - -6 T:- -CT:- - -7 T:- -CT:- - -: Select 0-9 : Input : PlayMemoryMemory playback/Random playback1Press MEMORY.2Press  /  toselect “T” or “CT”.Use Number keysto Input thefavorite number.3Press or ENTER.Set the “T” and“CT” to bar thatyou want to enteras In step 2.4Press PLAY to start MEMORY playback.You can arrange the order of titles, chapter or tracks on the disc.Memory playbackTurn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••NOTES:•The memory is cancelled whenpress STOP during memory playback.•Random playback can not becombined with Repeat playback.•You can program up to 30 selectionsinto the memory.•Depending on the DVD, ChapterRandom operation may not workduring playback.•You cannot use the random playbackwith memory playback.EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATRT : Title numberCT : Chapter number or track number•When you select another chapter In thesame title, you do not need to select thetitle number.Ramdom playback12Press PLAY MODE repeatedly to select “ Chapter Random”or “Title Rondom”.(In case of CD, select Track Random)During play random playback will start automatically.During stop mode press PLAY within about 5 seconds afteryou press the PLAY MODE button to start random playback.•To resume normal playback, select Off.: Select 0-9 : Input : PlayMemory1 T:01 CT:0022 T:02 CT:0043 T:- -CT:- - -4 T:- -CT:- - -5 T:- -CT:- - -6 T:- -CT:- - -7 T:- -CT:- - -In stop modeIn stop mode1 T:- -CT:- - -: Select 0-9 : Input : PlayMemoryIn play back: Select 0-9 : Input : PlayMemory1 T:01 CT:0022 T:- -CT:- - -3 T:- -CT:- - -4 T:- -CT:- - -5 T:- -CT:- - -6 T:- -CT:- - -7 T:- -CT:- - -In stop mode1 T:01 CT:002: Select 0-9 : Input : PlayMemoryIn play back2 T:02 CT:004: Select 0-9 : Input : PlayMemoryIn play backTrack RandomCDChapter RandomDVD•To resume normal playback, press CANCEL. 2A70101A(38-43) 04/12/2001, 23:0739
40EAM: Select : EnterT1 000:23MP3PCM43MP3 PlaybackThis player can play back the MP3-datawhich recorded on CD-R or CD-RW. Toproduce the MP3-data, you need a Windows-PC with CD-ROM drive and a MP3-encodingSoftware (not supplied).The Apple-HFS-System can not be played.Limitations on MP3 CD playback•MP3 CD is the disc that standardized byISO9660, its file name must include 3-digitsextension letters, “mp3”.•The directory and file names of the MP3CD must be corresponded to the ISOstandardized files.•This unit can read 200 files per one disc. Ifone directory has more than 200 files, itreads up to 200 files, the more files will beomitted.•As for multi-session disc, only the firstsession can be played.•If the CD has both audio tracks and MP3files, only audio tracks are played.•It would take one minute or more for thisunit to read MP3 files depending on itsstructure.•Music recorded by “Joliet RecordingSpecification” can be played back, the filename is displayed (within 8 letters) on thescreen shorter than the actual file names.•The music files recorded by “HierarchicalFile System” (HFS) cannot be played.Press DISPLAY.Then press  / to selectMP3 and press ENTER.Press  / or / to select your desired track, then pressENTER. Track is selected and play commences.• In case the folder include more than 9 tracks, press /to display next track list.• To remove track list, press CANCEL.• Press / to select “T” and press Number keys yourdesired to input.Limitations on display•The maximum number for display is 8letters. Available letters for display are thefollowing: capital or small alphabets of Athrough Z, numbers of 0 through 9, and _(under score).•Other letters than those above are replacedin hyphen.Notes on MP3 filesTo play back MP3 CD in the recorded order,1. please use the MP3 software with thefunction that can record data alphabeticallyor numerically.2. we recommend you to put the nameincluding two-digit or threedigit numberlike “01” “02” or “001” “002” on each file.3. please refrain from making many sub-folders by preference.CAUTION:•Some MP3 CDs can not be played backdepending on the recording conditions.•The CD-R/RW that has no music data ornon-MP3 files can not be played back.5Press STOP to end playback.• The unit records the stopped point.Press PLAY to resume playback (from the scene point).• If you press STOP again or unload the disc, the unit willclear the stopped point.6Then press OPEN/CLOSE.The disc tray opens.Remove the disc and press POWER.The disc tray closes automatically and DVD/VCR turns off.1Press OPEN/CLOSE.The disc tray will open.Then place a disc onto the tray.2Press PLAY or OPEN/CLOSE.The disc tray closes automatically.On the TV-screen, “” and thenreading file number will appear.Reading will take as muchtime as the number of file.MP3 CD InformationNOTES:During MP3-Playback, you can not use SEARCH, A-BRepeat functions.You can use Repeat(Track or All) and Random functions forMP3 CD Playback.(See page 38 and 39)••Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVDindicator will light)Preparation:••EAM: Select : SearchT1 000:23MP3PCM1. \ CRYINI~12. \ DANGER~13. \ GITARREN4. \ LILYWA~15. \ MERCYS~16. \ OBSESS~17. \ PINKPA~18. \ RUNNIN~1T11 2A70101A(38-43) 04/12/2001, 23:0740
41: Select : ReturnSubtitle:ENG1 On: On/OffENG 1SPA 1FRE 1Off: Select : ReturnSubtitle:- - - OffENG 1SPA 1FRE 1Off: Select : ReturnAudio:ENG1 2CH2CHENG2 5.1CHFRE1 2CHENG1 2CH: Select : ReturnAudio:FRE1 2CH2CHENG2 5.1CHFRE1 2CHENG1 2CHEJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F FWDPOWERTIMER REC SUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERChanging soundtrack language / Changing Subtitles language1Press AUDIO during playback.The current soundtrack languageis displayed.2Press AUDIO repeatedly untilthe desired language is selected.The on-screen display will disap-pear after a few seconds.Changing soundtrack languageTurn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••Press SUB TITLE duringplayback.Then press  / to select thedesired language.• To turn off the subtitle settingdisplay, press the CLEAR orENTER buton.• To turn the subtitles off, select“Off”.Changing Subtitles languagePress  SUB TITLE or / toturn Subtitles on or off.You can select the language when playing back a disc  recordedwith multi-lingual subtitles.You can select the language when you play a multilingual disc.NOTES:•If the desired language is not heard   afterpressing the button several times, thelanguage is not recorded on the disc.•Changing soundtrack or subtitlelanguage is cancelled when you open thedisc tray or turn the power off. The initialdefault language or available languagewill be heard and seen if the disc isplayed back again.•Depending on the DVD, you may not beable to turn the subtitles on even if theyare recorded on it. Depending on theDVD, you may not be able to turn thesubtitles off even if you set the subtiltefunction to off. Depending on the DVD,you may not be able to change the subti-tles even if multilingual subtitles are re-corded on it. While playing the DVD, thesubtitle may change when: -you open orclose the disc tray -you change the title.•During some scenes, the subtitles may notappear immediately after you select “On”.•The abbreviation of the languageappears instead of the language name.Refer to the list of languages and theirabbreviations. (See on page 55)12 2A70101A(38-43) 04/12/2001, 23:0741
42: Select : ReturnAngle :1231EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATRChanging angles / Title selection / DVD menuWhen playing back a disc recorded with multi-angle facility, youcan change the angle that you are viewing the scene from.1Press ANGLE during playback.The current angle will appear.2Press  ANGLE  or  / repeatedly until the desired angle isselected.• To turn off the angle number display, press the CLEAR.• You can change the camera angle directly by pressing the   number keys corresponding to its angle number instead of   using the  / buttons.Changing AnglesTwo or more titles are recorded on some discs. If the title menuis recorded on the disc, you can select the desired title.1Title menu appears on the screen.•Press  TITLE again to resume playback at the scenewhen you pressed TITLE.2Press  /  or  / to select the desired title.3Title SelectionSome DVDs allow you to select the disc contents using themenu.When you play back these DVDs, you can select the subtitlelanguage and sound-track language,etc. using the DVD menu.Press ENTER.The menu continues to another screen. Repeat steps 2 and 3 toset the item completely.1Press DVD MENU during playback.The DVD menu appears on the screen.•Press DVD MENU again to resume playback atthe scene when you pressed DVD MENU.2Press  /  or  / to select the desired item.3DVD MenuNOTES:Depending on the DVD, you may notbe able to change the angles even ifmulti-angles are recorded on the DVD.Depending on the DVD, you may notbe able to select the title.Depending on the DVD, a "title menu"may simply be called a "menu" or "title"in the instructions supplied with thedisc.•••Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••Press ENTER or PLAY.The playback of the selected title will start. 2A70101A(38-43) 04/12/2001, 23:0842
43ABCOperationTitle Stop OffParental Lock OffPause/Still AutoOnOff: Select : EnterABCOperationTitle Stop OffParental Lock OffPause/Still AutoOnOff: Select : EnterParental control1Press SETUP MENU in the stop mode.Press or to select “Operation”.2Press   or   to select “Parental Lock”,then press ENTER.3Press   or   to select Off or On.4Press Number keys to input a 4-digitspassword then press the ENTERbutton.•If you input a wrong number, pressCANCEL.Parental control settingTurn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••Off: The parental lock feature doesnot function.After pressing the ENTER button,follow step 4 below.On: To activate the parental lock fea-ture or change the settings.After pressing the ENTER button, follow steps 4-6 below.Some discs are specified not suitablefor children. Such discs can be limitednot to play back with the unit.ABCPictureTV Shape 4:3LB: Select : Enter5Enter the code of a country/area whosestandards were used to rate the DVDdisc. (See the list on the page 44)NOTES:If each setup (page 43~53) has beencompleted, the unit can always beworked under the same conditions(especially with DVD discs).Each setup will be retained in thememory if you turn the power off.Depending on the discs, the unit can-not limit playback.Some discs may not be encoded withspecific rating level information thoughits disc jacket says "adult". For thosediscs, the age restriction will not work.Do not forget the password. If you forgetthe password, contact the dealer thatyou purchased the unit from.••••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATRABCOperationTitle Stop OffParental Lock OffPause/Still AutoSecurity Code ----: Select : EnterOnOffABCOperationTitle Stop OffParental Lock OffPause/Still AutoOnOff: Select : EnterArea Code U S 2A70101A(38-43) 04/12/2001, 23:0843
44Parental control (Continned)To change the parental lock levelFollow steps 4- 6.6Press the  / buttons to select the parental lock level, thenpress the ENTER button.You cannot play DVD discs reted higher than the level you selectedunless you cancel the parental lock function.For example, when you select level 7, discs rated higher than level7 are locked out and cannot be played.The parental lock level is equivalent to following USA movie ratings.Level 7: NC-17Level 6: RLevel 4: PG 13Level 3: PGLevel 1: GABCOperationTitle Stop OffParental Lock OffPause/Still AutoOnOff: Select : EnterLevel 7Area Code U SThe parental lock levels for other countries/areas than U.S. areincluded for future use. Check the appropriate parental lock levelwhen you buy a DVD disc equipped with the parental lock feature inthe future.To change your 4-digit security code1) After selecting “On” or “Off” press the STOP button four times,then press the ENTER button.The 4-digit security code is cleared.2) Press the Number Keys buttons to create a new 4-digit securitycode.3) Press the ENTER button.Country/Area CodeNETHERLANDS NLNORWAY NOPHILIPPINES PHRUSSIAN FEDERATION RUSINGAPORE SGSPAIN ESSWEDEN SESWITZERLAND CHTAIWAN TWTHAILAND THUNITED KINGDOM GBUNITED STATES USa) Press  / to select the first character.b) Press the  / to shift and press  / to select the secondcharacter.c) Press the ENTER buton.Country/Area CodeAUSTRALIA AUBELGIUM BECANADA CACHINA                                CNCHINA HONG KONG HKDENMARK DKFINLAND FIFRANCE FRGERMANY DEINDONESIA IDITALY ITJAPAN JPMALAYSIA MYEJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(44-49) 04/12/2001, 23:0844
45ABCLanguageSubtitle Language ENGAudio Language ENGOn-Screen Language ENGSpanishOthersCode E SFrench: Select : EnterDisc Menu Language ENGEnglishSetting menu languagePress ENTER.Press   or   to select yourdesired language, then pressENTER.123To make SETUP screen disappear, press SET UP.OTHER: Other language can be selected (See the Table oflanguages on page 55).English, French, SpanishThe selected language is the first-priority Menu language.Press   or   to select “DiscMenu Language”.4You can select the language of thedisc menu messages of DVDs. Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••Press SET UP in the stop mode.Press   or   to select“Language”.ABCPictureTV Shape 4:3LB: Select : EnterABCLanguageSubtitle Language ENGAudio Language ENGDisc Menu Language ENGOn-Screen Language ENG: Select : EnterEJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRSUB TITLE/ATRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTER 2A70101A(44-49) 04/12/2001, 23:0845
46ABCLanguageSubtitle Language ENGAudio Language ENGDisc Menu Language ENGOn-Screen Language ENG: Select : EnterSpanishNo SubtitleOthersCode E SFrenchEnglishABCLanguageSubtitle Language ENGAudio Language ENGDisc Menu Language ENGOn-Screen Language ENG: Select : EnterABCPictureTV Shape 4:3LB: Select : EnterIf you want to select another language, enter the language code(See the Table of languages on page 55).OTHER:English, French, SpanishThe subtitle is displayed with the selected language if it isrecorded on the disc.Setting subtitle languagePress ENTER.Press   or   to select yourdesired language, then pressENTER.1Press SET UP in the stop mode.Press   or   to select“Language”23To make SETUP screen disappear, press SET UP.4NOTES:•If the selected language is not recordedon the disc, the first-priority language isselected.•Some DVD discs may be set to displaySubtitles in a different language thanyou selected. A prior subtitle languagemay be programmed on the disc.The same subtitle language canalways be selected even if you replacethe disc or turn the power off.Press   or   to select “SubtitleLanguage”.Subtitles do not appear.No Subtitle:Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(44-49) 04/12/2001, 23:0846
47ABCPictureTV Shape 4:3LB: Select : EnterABCLanguageSubtitle Language ENGAudio Language ENGDisc Menu Language ENGOn-Screen Language ENG: Select : EnterSpanishOthersCode E SFrenchEnglishABCLanguageSubtitle Language ENGAudio Language ENGDisc Menu Language ENGOn-Screen Language ENG: Select : EnterSetting audio soundtrack languagePress ENTER.Press   or   to select yourdesired Audio Language, thenpress ENTER.1Press SET UP in the stop mode.Press   or   to select“Language”23To make SETUP screen disappear, press SET UP.4NOTES:•If the selected language is not re-corded on the disc, the originallanguage will be heard.•Some DVD discs may be played in adifferent language than you selected.A prior language may be programmedon the disc.The same audio soundtrack languagecan always be selected by your uniteven if you replace the disc or turnthe power off.English, French, SpanishThe language you have selected will play if it is recorded onthe disc.Press   or   to select “AudioLanguage”.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATROTHER: If you want to select another language,enter the language code (See the Table of languages on page55). 2A70101A(44-49) 04/12/2001, 23:0847
48ABCPictureTV Shape 4:3LB: Select : EnterSetting the aspect ratio of TV screenPress ENTER.Press   or   to select yourdesired screen type, then pressENTER.1Press SET UP in the stop mode.Press  or  to select“Picture”.2To make SETUP screen disappear, press SET UP.3NOTES:•The displayable picture size is preset onthe DVD video disc. Therefore, theplayback picture of some DVD videodiscs may not conform to the picture sizeyou select.•When you play DVD video discsrecorded in the 4:3 picture size only, theplayback picture always appears in the4:3 picture size regardless of the TVshape setting.•If you select “16:9 widescreen” and youown a 4:3 TV set, the DVD playbackpicture will be horizontally distortedduring playback. Images will appear tobe horizontally compressed. Always besure that your TV shape conforms to theactual TV in use.You can select the aspect ratio foryour TV.4:3 Letterbox:Select when a standard 4:3 TV is connected.Displays theatrical images with masking bars above and belowthe picture.4:3 Normal:Select when a standard 4:3 TV is connected.Displays pictures cropped to fill your TV screen. Either or bothsides of the picture are cut off.16:9 Widescreen:Select this mode when connecting to a wide-screen TV.A wide screen picture is displayed full size.You have the following screen sizes to choose from:ABCTV Shape 4:3LBPicture: Select : Enter16:9 Widescreen4:3 Normal4:3 LetterboxTurn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BPOWERTIMER RECMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATR 2A70101A(44-49) 04/12/2001, 23:0848
49ABCDisplayScreen Saver OnBackground PictureOn-Screen Display On: Select : EnterABCPictureTV Shape 4:3LB: Select : EnterABCDisplayScreen Saver OnBackground PictureOn-Screen Display OffOnOff: Select : EnterEJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATRSetting on Screen displayPress ENTER.Press   or   to select “On” or“Off”, then press ENTER.123To make SETUP screen disappear, press SETUP.4On screen display can be switched onor off when you press the buttons.On: Operational modes (e.g.  “ ”, “ ”) appear when youpress the buttons (factory setting).Off: Operational modes (e.g.  “ ”, “ ”) do not appear whenyou press any buttons.Press   or   to select “On-Screen Displays”.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicatorwill light)Preparation:••Press SET UP in the stop mode.Press   or   to select “Display” 2A70101A(44-49) 04/12/2001, 23:0849
50ABCAudioKaraoke Vocal OnDynamic Range ControlOnAudio Out Select BitstreamAnalog 2chPCMBitstream: Select : EnterSetting Audio1Press SET UP in the stop mode.Press  or  to select “Audio”.2NOTES:•Dynamic Range Control function worksonly during playback of Doldy Digitalrecorded discs.•The level of Dynamic Range Controlmay differ depending on the DVD videodisc.•The vocal output feature is used duringplayback of Dolby Digital (multi-channel)recorded DVD KARAOKE discs. Thisfeature allows you to turn off vocal audiotracks, or restore them for backgroundaccompaniment.•When playing KARAOKE, connectappropriate audio equipment such asamplifier to the DVD video player.Press   or   to select “Audio OutSelect”, then press ENTER. Press   or to select your desired output sound,then press ENTER.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicator will light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATRAudio Out SelectSelect the output sound format corresponding to your system connection.For details of sound recording systems, see on page 53.Bitstream: Select when connected to an amplifier equipped with a DolbyDigital, DTS, MPEG1 or MPEG2 decoder. The DVD/VCR outputsdigital audio information in the bitstream format when you play aDVD video disc recorded on the Dolby Digital, DTS, MPEG1 orMPEG2 recording system.Analog 2ch: Select when connected to a TV, Dolby Pro Logic or stereo systemvia the analog audio jacks.PCM: Select when connected to a 2 channel digital stereo amplifier.The DVD/VCR outputs sounds in the PCM 2ch format when youplay a DVD video disc recorded on the Dolby Digital. MPEG1 orMPEG2 recording system.Dynamic Range ControlTurn on or off a function that makes faint sounds easier to heareven if you lower the volume during late hours playback.3To make SETUP screen disappear, press SET UP.1Press SET UP in the stop mode.Press  or  to select “Audio”.2Press   or   to select “DynamicRange Control”, then press ENTER.Press   or   to select “On” or “Off”,then press ENTER.ABCAudioKaraoke Vocal OffDynamic Range ControlOnAudio Out Select Bitstream: Select : EnterOnOffOff: Full dynamic range is maintained.On: Dynamic range is reduced.3To make SETUP screen disappear,press SET UP.Karaoke VocalTurn on or off the vocal output during DVD KARAOKE discplayback.1Press SET UP in the stop mode.Press  or  to select “Audio”.2Press   or   to select “KaraokeVocal”, then press ENTER.Press   or   to select “On” or “Off”,then press ENTER.ABCAudioKaraoke Vocal Off: Select : EnterDynamic Range ControlOnAudio Out Select BitstreamOnOffOff: The primary vocal is not output.On: The primary vocal is output whenit is recorded on the disc.3To make SETUP screen disappear, pressSET UP. 2A70101A(50-BACK) 04/12/2001, 23:0850
51ABCOperationTitle Stop OffParental Lock OffPause/Still AutoFrameAuto: Select : EnterABCPictureTV Shape 4:3LB: Select : EnterSetting Operation1Press SET UP in the stop mode.Press  or  to select“Operation”.2Press   or   to select “Pause/Still”, then press ENTER. Press or   to select “Auto” or“Frame”, then press ENTER.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicator will light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATRPause/StillSelect the resolution of still pictures.Title StopTurn on or off a feature that automatically stops playback after atitle has been viewed.1Press SET UP in the stop mode.Press  or  to select “Operation”.ABCPictureTV Shape 4:3LB: Select : EnterAuto: For normal use. Still and fast motion images can bepaused.Frame: The resolution of still pictures is improved, so that youcan make a motionless picture more clearer when youpause it.2Press ENTER, then press  or to select “Title Stop”, thenpress ENTER.Press  or   to select “On” or“Off”, then press ENTER.ABCOperationTitle Stop OffParental Lock OffPause/Still Auto: Select : EnterOnOff3To make SETUP screen disappear, press SET UP.3To make SETUP screen disappear, press SET UP.Off: The DVD/VCR continuesafter playback of a title iscompleted.On: The DVD/VCR stops afterplayback of a title is com-pleted. 2A70101A(50-BACK) 04/12/2001, 23:0851
52ABCPictureTV Shape 4:3LB: Select : EnterSetting Background/Setting Screen Saver1Press SET UP in the stop mode.Press  or  to select “Display”.2Press   or   to select“Background”, then pressENTER. Press   or   toselect your desired background,then press ENTER.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicator will light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELANGLE/COUNTER RESETCLOCK/COUNTERPLAY MODE/SPEEDAUDIO/AUDIO SELECTTV/VCRPLAYINDEX/SKIPSKIP/INDEXSLOW PAUSE/STILLSTOPZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BREW/SEARCH SEARCH/F.FWDPOWERTIMER RECREC/OTRMEMORY/ZERO RETURN123INPUT SELECT4560789SELECT/ENTERSUB TITLE/ATRSetting BackgroundSelect the background color or background picture.Setting Screen SaverTo turn the screen saver on or off.3To make SETUP screen disappear, press SET UP.ABCDisplayScreen Saver OnBackground PictureOn-Screen DisplayOnGrayPictureJacketBlue: Select : EnterBlue: Blue background.Gray: Gray background.Picture: Use the picture which appears when you turn on the DVD/VCR as a background.Jacket: Use the jacket picture included on some discs as abackground. If it is not included, a gray background will besubstituted.ABCPictureTV Shape 4:3LB: Select : Enter1Press SET UP in the stop mode.Press  or  to select“Display”.2Press   or   to select “ScreenSaver”, then press ENTER.Press  or   to select “On” or“Off”, then press ENTER.3To make SETUP screen disappear, press SETUP MENU.ABCDisplayScreen Saver OnBackground PictureOn-Screen DisplayOnOnOff: Select : EnterOff: The screen saver is disen-gaged.On: The sreen saver operates. 2A70101A(50-BACK) 04/12/2001, 23:0852
53Fran aisEspa olABCInitial SetupAudio Out Select BitstreamTV Shape 4:3LBOn-Screen Language ENG English: Select : EnterABCPictureTV Shape 4:3LB: Select : Enter1Press SET UP in the stop mode.Press  or  to select “InitialSetup”.2Press ENTER, then press   or to select “On-ScreenLanguage”, “TV Shape” or“Audio Out Select”.Turn ON the TV and set to the video input mode.Press VCR/DVD to select the DVD mode. (The DVD indicator will light)Preparation:••EJECTOPEN/CLOSECHCHDVD MENU RETURNSET UP/VCR MENU CLEAR/CANCELZOOMVCR/DVDDISPLAY/CALLTRACKING/SET—TRACKING/SET+TITLE REPEAT A-BPOWER123INPUT SELECT4560789SELECT/ENTERSetting Initial SetupSetting Initial Setup/Output Sound Conversion TableYou can install the initial systemsetting.On-Screen Language: See on page 34.TV Shape: See on page 37.Audio Out Select: See on page 50.Output sound conversion table (sampling frequency/quantization bit)You can select the output sound format corresponding to your system connection (see page 50).48 kHz/16 bit48 kHz/20 bit48 kHz/24 bit96 kHz/16 bit96 kHz/20 bit96 kHz/24 bitDIGITAL AUDIOOUT jackBitstreanBitstreamBitstream44.1 kHz/16 bitBitstreamANALOG AUDIOOUT jack(Noise)Recording systemDolby DigitalDTSMPEG1, MPEG2Linear PCM 44.1 kHz/16 bitDTSLinear PCMDIGITAL AUDIOOUT jackBitstreanBitstreamBitstream——48 kHz/16 bit44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bitBitstreamANALOG AUDIOOUT jack(Noise)———DIGITAL AUDIOOUT jack48 kHz/16 bit48 kHz/16 bit—48 kHz/16 bit44.1 kHz/16 bitBitstreamANALOG AUDIOOUT jack(Noise)Bitstrean Analog 2ch PCMDiscsAudio CDsDVD video discs48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/20 bit48 kHz/16 bit48 kHz/20 bit48 kHz/24 bit48 kHz/16 bit48 kHz/20 bit48 kHz/24 bit48 kHz/20 bit—48 kHz/16 bit44.1 kHz/16 bit48 kHz/16 bit48 kHz/20 bit48 kHz/24 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/16 bit48 kHz/20 bit48 kHz/24 bit48 kHz/20 bit48 kHz/16 bit48 kHz/20 bit48 kHz/24 bit96 kHz/16 bit96 kHz/20 bit96 kHz/24 bit: 3D (N-2-2) sound enhancement can function. 2A70101A(50-BACK) 04/12/2001, 23:0853
54DVDStatus display of DiscYou can view Information on operation status and access and setting.Each Press of DISPLAY, the status display of the disc will appear on the screen and change as follows.1Press  or  to select your desired a symbol mark, then press ENTER.You can access the specific feature. T, C and   are no need to press ENTER.2T: Title number (Track number)Press  /  or Number keys to locate a title ortrack, then press PLAY.C: Chapter numberPress  / or Number keys to locate a Chapter,then press PLAY.: Elapsed (remaining) time of the current titlePress Number keys to locate a desired Location,then press PLAY. Audio settingSee page 41.: Subtitle settingSee page 41.: Angle settingSee page 42.ZOOM: To zoom a pictureSee page 37.: Audio Out Select settingBST: Bitstream 2CH:Analog 2ch PCM:PCMSee page 50.: To stop playbackSee page 35.: Playback starts from the beginning of thecurrent chapter or track.See page 36.: Fast reverse playbackSee Page 36.: To start playbackSee page 35.: Fast forward playbackSee page 36.: To pause playbackSee page 36.: To begin slow motion playbackSee page 36.: To locate succeeding chapters or tracks.See page 36.Data transfer rate (Mbit/s)Amount of picture, sound and subtitle data in the DVDvideo disc transferred per second.The larger the value is, the more data processed, butthis does not necessarily insure better picture quality.EAMT C23 0:08:162CHIOOMX 1CEPMEAMEAMT C23 -0:21:28ZOOM2CHIOOMX 1CEAMT C23 0:08:169.2MbpsBITRATE2CHIOOMX 1COFFEAMT C2 32CHIOOMX 1CCDEAMT100:302CHIOOMX 1CEPMEAMEAMT1-03:382CHIOOMX 1CEAMDisc Title:No TextTrack Title:No Text----- CD TEXT -----T1 01:142CHIOOMX 1CEAMT12CHIOOMX 1C: To turn off the displayCD TEXTDisplays CD text data if included on the audioCDs. (Some letters may not be displayedproperly depending on the disc.)OFFSymbol mark of the featureyou selected is displayed.PCM 2A70101A(50-BACK) 04/12/2001, 23:0954
55SYMPTOMS POSSIBLE SOLUTIONS•Make sure the power cord is plugged in.•Try another AC outlet.•Power is off, check fuse or circuit breaker.•Unplug unit, then plug it back in.•Select the DVD or VCR mode before operating.DVD/VCR does not operate.Problems and troubleshootingUse the following check list for troubleshooting when you have problems with your unit. Consult your localdealer or service outlet if problems persist.Be sure all connections are properly made when using with other units.DVD/VCRPAGE5––518,34The remote control does notfunction.• Aim at the remote control at the remote sensor.• Operate within Approx. 5 Meters or reduce the light in the room.• Clear the path of the beam.• The batteries are weak. Replace the batteries.• Check the batteries are inserted correctly.• Check the frequency code is set correctly.11DVDNo picture.• Antenna connection is not correct or antenna cable is disconnected.• The video channel is not in the correct position or the TV is notset to the video channel 3 or 4.• Check the unit is connected correctly.• The video input selector of the TV is not set to VIDEO. Set toVIDEO (or equivalent).• Channel is set to the external mode.No sound.• Check the unit is connected correctly.• Check the input selector of the amplifier is set properly.• The unit is in the Special playback mode.12~151812~17––12~17–24,36•Select proper language in the menu options.Display is not shown in yourlanguage. 34Playback doesn’t start.• No disc is inserted.• The disc may be dirty. Clean up the disc.• The unit cannot play DVD-ROMs, etc.Stopping playback, search, slow-motion play, repeat play, orprogram play, etc. cannot beperformed.• Some discs may not do some of the functions.353333–No CATV reception •Check all CATV connections.•Station or CATV system problems, try another station. 14,15Noise bars on screen.• Tracking adjustment beyond range of automatic tracking circuit.Try Manual tracking adjustment.• Video heads are dirty.• The tape is worn or damaged.VCR•The erase prevention tab of the video cassette is broken off.•The unit is in the external input mode.TV recording does not work. 22,26Timer recording does not work. • The time is not set correctly.• The recording start/end time is not set correctly.• The TIMER has not been pressed (  is not lit).1929292453– 2A70101A(50-BACK) 29/11/2001, 13:5055
56RNo subtitle • Some discs have no subtitles.• Subtitles are cleared. Press SUB TITLE.Angle cannot be changed. • Multi-angles are not recorded on the DVD disc.• The function is prohibited with the unit or the disc. appears on the screen.4642–SYMPTOMS POSSIBLE SOLUTIONS PAGEProblems and troubleshooting / Video head cleaningNOTES: •DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THEREAR COVER.•Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.•To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.Video head cleaningVideo head cloggingThe video heads are the means by which the DVD/VCR readsthe picture from the tape during playback. In the unlikely eventthat the heads become dirty enough to be clogged, no picturewill be played back. This can easily be determined if, duringplayback of a known good tape, there is good sound, but nopicture (picture is extremely snowy). If this is the case, havethe DVD/VCR checked by qualified service personnel. Good Picture Snowy PictureNo 4:3 (16:9) picture • The setup does not match your TV.No on-screen display • Select Display On.4849No surround sound • The setup does not match your stereo system.The unit or remote operation keyis not functioning.• Turn off the unit and unplug the AC power cord for severalminutes, then replug it.17Playback does not start when thetitle is selected. • Check the Parental setup.Audio soundtrack and/or subtitlelanguage is not changed whenyou play back a DVD. • Multilingual language is not recorded on the DVD disc.–4346,47OR WRITE TO:ORION SALES, INC.3471 N. UNION DR.OLNEY, ILLINOIS 62450FOR INFORMATION ON OUR OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE ATwww.orionsalesinc.comFOR CUSTOMER SERVICE,ADDITIONAL SET-UP OROPERATING ASSISTANCEPLEASE CALL:1-800-289-0980TO ORDER ACCESSORYPARTS OR LITERATUREPLEASE CALL:1-800-369-0304 2A70101A(50-BACK) 29/11/2001, 13:5056
57GENERALPower supply:Power consumption:Weight:Dimensions:Inputs/Outputs:Video:Audio:Antenna:Hi-Fi Frequency Response:Hi-Fi Dynamic Range:VCR sectionVideo Head:Audio Track:Tuner:RF Channel Output:F.FWD/REW Time:DVD sectionSignal system:Applicable disc:Audio characteristics:Frequency response:S/N Ratio:Harmonic distortion:Wow and flutter:Dynamic range:Output:Pickup:ACCESSORIES:AC 120V 60HzOperation: 20WStand by: 3W9.9lbs (4.5 kg)Width : 16-15/16 inches (430 mm)Height: 3-7/8 inches (99 mm)Depth : 12-3/8 inches (314.5 mm)In: 1Vp-p/75 ohmOut: 1Vp-p/75 ohmIn: –8dBm/50K ohmOut: –8dBm/1K ohmUHF/VHF IN/OUT: 75 ohm coaxial20Hz to 20,000HzMore than 90dB4 Rotary HeadsHi-Fi Sound - 2 Tracks / MONO Sound - 1 Track181 Channel Freq. SynthesizedVHF 2-13UHF 14-69CATV 14-36 (A)-(W)37-59 (AA)-(WW)60-85 (AAA)-(ZZZ)86-94 (86)-(94)95-99 (A-5)-(A-1)100-125 (100)-(125)01 (5A)Channel 3 or 4, SwitchableApprox. 1minutes and 48 seconds (with T-120 Cassette Tape)NTSCDVD (12cm, 8cm), CD (12cm, 8cm)DVD: 4Hz - 22KHzCD: 4Hz - 20KHz90dB0.01%Below Measurable Level90dBVideo : (RCA) 1 Vp-p/75ohmAudio : (RCA) –8 dBm/1KohmDigital Audio : 0.5Vp-p/75 ohmCD : Wavelength: 775 - 805 nmMaximum output power: 0.5 mWDVD : Wavelength: 640 - 660 nmMaximum output power: 1.0 mWRemote control x 175 ohm Coaxial Cable x 1AUDIO/VIDEO Cable x 1Specifications 2A70101A(50-BACK) 29/11/2001, 13:5057
58ORION warrants this product to be free from manufacturing defects in material and workmanship undernormal use and conditions for a period of ninety (90) days from date of original purchase in the United States only.Should service be necessary under this warranty for any reason due to a manufacturing defect or malfunc-tion during the first ninety (90) day period from date of original purchase, ORION will provide carry-in repairservice at an ORION authorized Independent Service Center at no charge. In addition, for a period of up to six(6) months from date of original purchase for video heads and twelve (12) months from date of original pur-chase for other component parts, if an original part fails due to a manufacturing defect in material or workman-ship we will replace the defective part only (EXCLUDING LABOR AFTER INITIAL NINETY (90) DAY WAR-RANTY PERIOD) provided the defect or malfunction is verified along with dated proof of purchase.There are ORION Independent Service Centers located throughout the country. For the one nearest you,DIAL TOLL FREE: 1-800-289-0980 or visit our website at www.orionsalesinc.com.  This product is eligible forCARRY-IN service only.  ORION will not be liable for damages incurred during shipment of the unit.  If there areno ORION authorized Independent Service Centers in your area please call – 1-888-296-7466 for assistance.Note: This warranty is void if the product is:(a) Damaged through negligence, misuse, or accident.(b) Used in a commercial application or rentals.(c) Modified or repaired by anyone other than an Independent Service Center authorized by ORION to effectwarranty repairs to the class of product or by the ORION Factory Service Center.(d) Damaged because it is improperly connected to the equipment of other manufacturers.This warranty does not cover:a) Damage to tape cartridge.b) Cleaning of video heads.c) Damage to DVD and CD discs.d) Damage to equipment not properly connected to the product.e) Costs incurred in the shipping of the product to an ORION authorized Independent Service Center orORION Factory Service Center.f) Damage or improper operation of unit caused by customer abuse, misuse, negligence, or failure to followoperating instructions provided with the product.g) Ordinary adjustments to the product, which can be performed by customer as outlined in the owner'smanual.THIS WARRANTY IS NON-TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASERAND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT. ANY APPLICABLE IMPLIEDWARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED IN DURATION TO APERIOD OF THE EXPRESS WARRANTY AS PROVIDED HEREIN BEGINNING WITH THE DATE OF ORIGI-NAL PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED SHALL APPLYTO THIS PRODUCT THEREAFTER. ORION MAKES NO WARRANTY AS TO THE FITNESS OF THE PROD-UCT FOR ANY PARTICULAR PURPOSE AND USE.UNDER NO CIRCUMSTANCES SHALL ORION BE LIABLE FOR ANY LOSS, DIRECT, INDIRECT,INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITHTHE USE OF THIS PRODUCT.THIS WARRANTY IS VALID ONLY IN THE UNITED STATES OF AMERICA. THIS WARRANTY GIVESYOU SPECIFIC LEGAL RIGHTS, HOWEVER, YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROMSTATE TO STATE. SOME STATES DO NOT ALLOW LIMITATION ON IMPLIED WARRANTIES OR EXCLU-SION OF CONSEQUENTIAL DAMAGE; THEREFORE, THESE RESTRICTIONS MAY NOT APPLY TO YOU.ORION SALES, INC.3471 N. UNION DR.OLNEY, ILLINOIS 62450SANSUIlimitedWARRANTYDVD PLAYER / VIDEO CASSETTE RECORDER COMBINATION UNIT 2A70101A(50-BACK) 29/11/2001, 13:5058
59Memo 2A70101A(50-BACK) 29/11/2001, 13:5059
2A70101A02/01ZPrinted in Thailand 2A70101A(50-BACK) 29/11/2001, 13:5060

Navigation menu