ORION ELECTRIC M2E5B VCR/DVD TV Interface Device User Manual Part 1

ORION ELECTRIC CO., LTD. VCR/DVD TV Interface Device Users Manual Part 1

Contents

Users Manual Part 1

21422293439IntroductionDIGITAL VIDEO42455567DVD VIDEO PLAYER & VIDEOCASSETTE RECORDERSD-V392SU2OWNER’S MANUAL©2004 Toshiba CorporationThis device does not tape-record copy protected DVD Video Discs.ConnectionsBasic setupPlayback(VCR)Recording(VCR)Other functions(VCR)Basic playback(DVD)Advancedplayback(DVD)Function setup(DVD)OthersJ2D81001A (E)COV.p65 28/5/04, 1:51 PM1
2IntroductionIMPORTANT SAFEGUARDSWARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rainor moisture.CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH ANEXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CANBE FULLY INSERTED TO PREVENT BLADE EXPOSURE.WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interferenceby one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.- Consult the dealer or an experienced radio/TV technician for help.CAUTION:Changes or modifications not expressly approved by the partly responsible for compliance with theFCC Rules could void the user's authority to operate this equipment.CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE-FULLY AND RETAIN FOR FUTURE REFERENCE.  SHOULD THE UNIT REQUIRE MAINTE-NANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHERTHAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLO-SURE.  VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.DO NOT STARE INTO BEAM.The lightning flash with arrowhead symbol, within anequilateral triangle is intended to alert the user to the presenceof uninsulated dangerous voltage within the product'senclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons.The exclamation point within an equilateral triangle is intendedto alert the user to the presence of important operating andmaintenance (servicing) instructions in the literatureaccompanying the appliance.RISK OF ELECTRIC SHOCKDO NOT OPENCAUTIONCAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLEPARTS INSIDE. REFER SERVICING TOQUALIFIED SERVICE PERSONNEL.  Location of the required MarkingThe rating sheet and the safety caution are on the rear of the unit.CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCESTANDARDS, 21 CFR SUBCHAPTER J.J2D81001A (E)p02-13.p65 28/5/04, 1:51 PM2
3Introduction1. READ INSTRUCTIONSAll the safety and operating instructions should be read before the unit is operated.2. RETAIN INSTRUCTIONSThe safety and operating instructions should be retained for future reference.3. HEED WARNINGSAll warnings on the unit and in the operating instructions should be adhered to.4. FOLLOW INSTRUCTIONSAll operating and use instructions should be followed.5. CLEANINGUnplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use a damp cloth for cleaning the exterior cabinet only.6. ATTACHMENTSThe manufacturer of this unit does not make any recommendations for attachments, as they may causehazards.7. WATER AND MOISTUREDo not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wetbasement, or near a swimming pool.8. ACCESSORIESDo not place this unit on an unstable cart, stand, tripod, bracket, or table.The unit may fall, causing serious injury, and serious damage to the unit.8A. An appliance and cart combination should be moved with care. Quick stops,excessive force, and uneven surfaces may cause the appliance and cartcombination to overturn.9. VENTILATIONSlots and openings in the cabinet back or bottom are provided for ventilation,to ensure reliable operation of the unit, and to protect it from overheating.These openings must not be blocked or covered. The openings should never be blocked by placing the uniton a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heatsource. This unit should not be placed in a built-in installation such as a bookcase or rack unless properventilation is provided and/or the manufacturer’s instructions have been adhered to.10. POWER SOURCEThis unit should be operated only from the type of power source indicated on the rating plate. If you are notsure of the type of power supply to your home, consult your appliance dealer or local power company. Forunits intended to operate from battery power, or other sources, refer to the operating instructions.11. GROUNDING OR POLARIZATIONThis unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than theother). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable toinsert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact yourelectrician to replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unitmay be equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug willonly fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the pluginto the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose ofthe grounding-type plug.12. POWER-CORD PROTECTIONPower-supply cords should be routed so that they are not likely to be walked on or pinched by items placedupon or against them, paying particular attention to cords at plugs, convenience receptacles, and the pointwhere they exit from the appliance.S3125APORTABLE CART WARNING(symbol provided by RETAC)IMPORTANT SAFEGUARDSJ2D81001A (E)p02-13.p65 28/5/04, 1:51 PM3
4IntroductionIMPORTANT SAFEGUARDS13. LIGHTNINGTo protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to theunit due to lightning and power line surges.14. POWER LINESAn outside antenna system should not be located in the vicinity of overhead power lines or other electriclight or power circuits, or where it can fall onto or against such power lines or circuits. When installing anoutside antenna system, extreme care should be taken to keep from touching such power lines or circuits,as contact with them might be fatal.15. OVERLOADINGDo not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.16. OBJECT AND LIQUID ENTRYDo not push objects through any openings in this unit, as they may touch dangerous voltage points or shortout parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.17. OUTDOOR ANTENNA GROUNDINGIf an outside antenna or cable system is connected to the unit, be sure the antenna or cable system isgrounded to provide some protection against voltage surges and built-up static charges, Section 810 of theNational Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mastand supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of groundingconductors, location of antenna discharge unit, connection to grounding electrodes, and requirements forthe grounding electrode.18. SERVICINGDo not attempt to service this unit yourself as opening or removing covers may expose you to dangerousvoltage or other hazards. Refer all servicing to qualified service personnel.For example:a. When the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into the unit.c. If the unit has been exposed to rain or water.d. If the unit does not operate normally by following the operating instructions. Adjust only those controlsthat are covered by the operating instructions, as an improper adjustment of other controls may result indamage and will often require extensive work by a qualified technician to restore the unit to its normaloperation.e. If the unit has been dropped or the cabinet has been damaged.f . When the unit exhibits a distinct change in performance, this indicates a need for service.19. REPLACEMENT PARTSWhen replacement parts are required, be sure the service technician uses replacement parts specified bythe manufacturer or those that have the same characteristics as the original part.Unauthorized substitutions may result in fire, electric shock or other hazards.20. SAFETY CHECKUpon completion of any service or repairs to this unit, ask the service technician to perform safety checks todetermine that the unit is in proper operating condition.21. HEATThe product should be situated away from heat sources such as radiators, heat registers, stoves, or otherproducts (including amplifiers) that produce heat.22. DISC TRAYKeep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.23. CONNECTINGWhen you connect the product to other equipment, turn off the power and unplug all of the equipment fromthe wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner'smanual of the other equipment carefully and follow the instructions when making any connections.J2D81001A (E)p02-13.p65 28/5/04, 1:51 PM4
5IntroductionEXAMPLE OF ANTENNA GROUNDING AS PER THENATIONAL ELECTRICAL CODE24. LASER BEAMDo not look into the opening of the disc tray or ventilation opening of the product to see the source of thelaser beam. It may cause sight damage.25. DISCDo not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause seriouspersonal injury and product malfunction.26. NOTE TO CABLE TV SYSTEM INSTALLERThis reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC thatprovides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-nected to the grounding system of the building, as close to the point of cable entry as practical.TO USE AC POWER SOURCEUse the AC polarized line cord provided for operation on AC. Insertthe AC cord plug into a standard 120V 60Hz polarized AC outlet.Notes:•Never connect the AC line cord plug to other than the specifiedvoltage (120V 60Hz). Use the attached power cord only.•If the polarized AC cord does not fit into a non-polarized ACoutlet, do not attempt to file or cut the blade. It is the user’sresponsibility to have an electrician replace the obsolete outlet.•If you cause a static discharge when touching the unit and theunit fails to function, simply unplug the unit from the AC outletand plug it back in. The unit should return to normal operation.Polarized AC Cord Plug(One blade is wider than the other.)AC OutletWider Holeand BladePower sourceANTENNADISCHARGE UNIT(NEC SECTION 810-20)ANTENNA LEAD IN WIREGROUNDING CONDUCTORS(NEC SECTION 810-21)GROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)GROUND CLAMPELECTRIC SERVICEEQUIPMENTNEC-NATIONAL ELECTRICAL CODES2898AIMPORTANT SAFEGUARDS / Power sourceJ2D81001A (E)p02-13.p65 28/5/04, 1:52 PM5
6IntroductionNotes on handlingWhen shipping the DVD/VCR, the original shippingcarton and packing materials come in handy. Formaximum protection, repack the unit as it wasoriginally packed at the factory.Do not use volatile liquids, such as insect spray, nearthe DVD/VCR. Do not leave rubber or plasticproducts to contact the DVD/VCR for a prolongedperiod. They will leave marks on the finish.The top and rear panels of the DVD/VCR maybecome warm after a long period of use. This is not amalfunction.When the DVD/VCR is not in use, be sure to removethe disc and the video cassette turn off the power.If you do not use the DVD/VCR for a long period, theunit may not function properly in the future. Turn onand use the DVD/VCR occasionally.Notes on locatingPlace the DVD/VCR on a level surface. Do not use iton a shaky or unstable surface such as a wobblingtable or inclined stand. The loaded disc or the videotape may become dis-aligned and damage the DVD/VCR.When you place this DVD/VCR near a TV, radio, orVCR, the playback picture may become poor and thesound may be distorted. In this case, place the DVD/VCR away from the TV, radio, or VCR.Notes on cleaningUse a soft, dry cloth for cleaning.For stubborn dirt, soak the cloth in a weak detergentsolution, wring well and wipe. Use a dry cloth to wipeit dry.Do not use any type of solvent, such as thinner andbenzine, as they may damage the surface of theDVD/VCR.If you use a chemical saturated cloth to clean the unit,follow that product’s instructions.To obtain a clear pictureThe DVD/VCR is a high technology, precision device. Ifthe video head, the head drum, the optical pick-up lensor disc drive parts are dirty or worn down, the picturequality will deteriorate. To obtain a clear picture, werecommend regular inspection and maintenance(cleaning or parts replacement) every 1,000 hours ofuse depending on the operating environment. Fordetails, contact your nearest dealer.Notes on moisture condensationMoisture condensation damages the DVD/VCR.Please read the following carefully.Moisture condensation occurs, for example, when youpour a cold drink into a glass on a warm day. Drops ofwater form on the outside of the glass. In the same way,moisture may condense on the head drum or the opticalpick-up lens inside this unit, one of the most crucialinternal parts of the DVD/VCR.Moisture condensation occurs during thefollowing cases.When you bring the DVD/VCR directly from a coldplace to a warm place.When you use the DVD/VCR in a room where youjust turned on the heater, or a place where the coldwind from the air conditioner directly hits the unit.In summer, when you use the DVD/VCR in a hot andhumid place just after you move the unit from an airconditioned room.When you use the DVD/VCR in a humid place.Do not use the DVD/VCR when moisturecondensation may occur.If you use the DVD/VCR in such a situation, it maydamage discs and internal parts. Remove the disc orthe video tape, connect the power cord of the DVD/VCR to the wall outlet, turn on the DVD/VCR, andleave it for two or three hours. After two or threehours, the DVD/VCR will have warmed up andevaporated any moisture. Keep the DVD/VCRconnected to the wall outlet and moisturecondensation will seldom occur.PrecautionsExampleofmoisturecondensation!TapeHead drumIt’s toowarm!Wait!Wall outletJ2D81001A (E)p02-13.p65 28/5/04, 1:52 PM6
7IntroductionNotes on discsOn handling discsDo not touch the playback side of the disc.Do not attach paper or tape to discs.On cleaning discsFingerprints and dust on the disc cause picture andsound deterioration. Wipe the disc from the centeroutwards with a soft cloth. Always keep the discclean.If you cannot wipe off the dust with a soft cloth, wipethe disc lightly with a slightly moistened soft cloth andfinish with a dry cloth.Do not use any type of solvent such as thinner,benzine, commercially available cleaners or antistaticspray for vinyl LPs. It may damage the disc.On storing discsDo not store discs in a place subject to direct sunlightor near heat sources.Do not store discs in places subject to moisture anddust such as a bathroom or near a humidifier.Store discs vertically in a case. Stacking or placingobjects on discs outside of their case may causewarping.Playback sideDVD video discTitle 1 Title 2Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3Track 1 Track 2 Track 3 Track 4 Track 5Structure of disc contentsNormally, DVD video discs are divided into titles, andthe titles are sub-divided into chapters. VIDEO CDs andaudio CDs are divided into tracks.DVD video discVideo CD/Audio CDEach title, chapter or track is assigned a number, whichis called “title number”, “chapter number” or “tracknumber” respectively.There may be discs that do not have these numbers.Notes on copyrightIt is forbidden by law to copy, broadcast, show,broadcast on cable, play in public, and rent copyrightedmaterial without permission.This device does not tape-record copy protected DVDVideo Discs.The device is not to be used for copying copyrightedcontent without the express written permission of thecopyright owner.Obtaining such permission is the sole responsibility ofthe user.This product incorporates copyright protectiontechnology that is protected by method claims of certainU.S. patents and other intellectual property rightsowned by Macrovision Corporation and other rightsowners. Use of this copyright protection technologymust be authorized by Macrovision Corporation, and isintended for home and other limited viewing uses onlyunless otherwise authorized by MacrovisionCorporation. Reverse engineering or disassembly isprohibited.Video CD/Audio CDJ2D81001A (E)p02-13.p65 28/5/04, 1:52 PM7
8IntroductionDIGITAL VIDEOAbout this owner’s manualThis owner’s manual explains the basic instructions ofthis DVD/VCR. Some DVD video discs are produced ina manner that allows specific or limited operation duringplayback. As such, the DVD/VCR may not respond to alloperating commands. This is not a defect in the DVD/VCR. Refer to instruction notes of discs.“” may appear on the TV screen during operation.A “ ” means that the operation is not permitted by theDVD/VCR or the disc.For example, sometimes it is unable to stop theplayback of copyright message of the disc when theSTOP ( ) button is pressed. Alternatively, the “ ” mayalso indicate that the feature is not available for the disc.Notes on region numbersThe region number of this DVD/VCR is 1. If regionnumbers, which stand for their playable area, are printedon your DVD video disc and you do not find  1 or ALL ,disc playback will not be allowed by the player. (In thiscase, the DVD/VCR will display a message on-screen.)On Video CDsThis DVD/VCR supports Video CDs equipped with thePBC (Version 2.0) function. (PBC is the abbreviation ofPlayback Control.) You can enjoy two playbackvariations depending on types of discs.• Video CD not equipped with PBC function(Version 1.1)Sound and movie can be played on this DVD/VCR inthe same way as an audio CD.• Video CD equipped with PBC function(Version 2.0)In addition to operation of a Video CD not equippedwith the PBC function, you can enjoy playback ofinteractive software with search function by using themenu displayed on the TV screen (Menu Playback).Some of the functions described in this owner’smanual may not work with some discs.Playable discsThis DVD/VCR can play the following discs.• You cannot play discs other than those listed above.• You cannot play discs of DVD-RAM, DVD-ROM,Photo CD, etc., or non standardized discs even if theymay be labeled as above.• Some CD-R/RWs cannot be played back dependingon the recording conditions.• This DVD/VCR uses the NTSC color system, andcannot play DVD video discs recorded in any othercolor system (PAL, SECAM, etc.).Notes on discs (continued)DVDvideodiscsDisc MarkContentsDiscSize Maximumplayback timeVideoCDsApprox. 4 hours(single sided disc)Approx. 8 hours(double sided disc)Approx. 80 minutes(single sided disc)Approx. 160 minutes(double sided disc)Approx. 74 minutesApprox. 20 minutes8 cm12 cm8 cm12 cmAudio+Video(movingpictures)Audio+Video(movingpictures)AudioCDsApprox. 74 minutesApprox. 20 minutes8 cm(CDsingle)12 cmAudioThe following discs are also available.DVD-R/RW discs of DVD video formatCD-R/CD-RW discs of CD-DA, Video CD, SVCD,MP3, WMA or JPEG formatKodak Picture CD and FUJICOLOR CD formatSome of these discs may be incompatible.J2D81001A (E)p02-13.p65 28/5/04, 1:52 PM8
9IntroductionIMPORTANT SAFEGUARDS ..........................2Power source ...................................................5Precautions ......................................................6Notes on discs..................................................7Contents. ..........................................................9Identification of controls .................................10Antenna connections......................................14Cable TV connections ....................................16Connecting to a TV ........................................18Connecting to optional equipment..................20IntroductionRecording a TV program ................................ 34One-touch Timer Recording (OTR) ................ 36Timer recording .............................................. 37Recording (VCR)Stereo recording and playback ...................... 39Second Audio Program (SAP)........................ 39Duplicating a video tape ................................. 40Recording a DVD/CD disc.............................. 41Other functions (VCR)Loading and unloading a cassette tape ......... 29Cassette tape playback .................................. 30Special playback ............................................ 31Convenience function..................................... 32Playback (VCR)Setting the video channel ............................... 22Setting the language ...................................... 23Clock setting................................................... 24Tuner setting .................................................. 27Basic setupPlaying a disc ................................................. 42Basic playback (DVD)MP3/WMA/JPEG playback ............................ 45Zooming ......................................................... 50Locating desired scene .................................. 50Marking desired scenes ................................. 51Repeat playback ............................................ 52A-B Repeat playback ..................................... 52Program playback (CD).................................. 53Random playback (CD) .................................. 53Changing angles ............................................ 54Title selection ................................................. 54DVD menu...................................................... 54Advanced playback (DVD)Language code list ......................................... 67Troubleshooting ............................................. 68Specifications ................................................. 69Limited warranty ............................................. 70OthersContentsConnectionsFunction setup (DVD)Changing soundtrack language ..................... 55Setting surround sound .................................. 55Setting subtitles .............................................. 56Karaoke playback........................................... 56E.B.L. (Enhanced Black Level) ...................... 57Setting the aspect ratio of TV screen ............. 58Setting on screen display ............................... 59Status display of disc ..................................... 59Dynamic Range Control ................................. 60Parental control setting .................................. 61To change the parental level .......................... 62Temporary disabling of rating level by DVD disc ..63Setting OSD language ................................... 64Setting language ............................................ 65Selecting PROGRESSIVE scan..................... 66J2D81001A (E)p02-13.p65 28/5/04, 1:52 PM9
10IntroductionIdentification of controlsSee the page in   for details.Front panel Rear panelWhen connecting the optical digital cable, remove the cap and fit the connector into the jack firmly.When not using the jack, keep the cap inserted to protect it from dust intrusion.ON/STANDBYbuttonAUDIO (L/R)/VIDEO IN(LINE IN 2) jacks2240EJECT button29Cassette loading slot29Disc tray42Display window11REC button34CHANNEL #/$ buttons34OPEN/CLOSE button42STOP buttonPLAY buttonFF (Fast Forward)buttonREW (Rewind) button3030 3030VCR/DVD mode selector button22Remote sensor13VCR indicatorDVD indicator4222DVD S-VIDEOOUT jack 19S-VIDEO/COMPONENTVideo selector switch19DVD OPTICAL DIGITAL AUDIOOUT jack (dust protection cap)20DVD AUDIO (L/R)OUT jacks19DVD COAXIAL DIGITALAUDIO OUT jack20DVD COMPONENTOUT jacks19RF OUT jack14RF IN jack14AUDIO (L/R)/VIDEOIN (LINE IN1) jacks40DVD/VCR common AUDIO(L/R)/VIDEO OUT jacks185AC power cordJ2D81001A (E)p02-13.p65 28/5/04, 1:52 PM10
11IntroductionVCR operation statusCH  1258 : 47AM   MON00 : 00 : 00  SPSTEREO  SAPWhile watching TVDAY OF THE WEEKCHANNELTAPE SPEEDREAL TIME COUNTERCLOCKSTEREO ANDSECONDAUDIOPROGRAM(SAP)8 : 30AM   MON00 : 15 : 12  SPHI-FISTEREOWhile operating a tapeOPERATINGMODETAPE INAUTO REPEATHI-FI STEREODVD/CD/VCD operation statusPress CALL to display information on screen.To cancel the display, press CALL again.Recording :Rec/Pause :Play :Stop :Eject :VCR Icons34:56 71:33Track 11/9900:34:56 01:12:33Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.DVD00:34:56 01:12:331/9Title 1/991/81/32Chapter 1/999Eng DolbyDigitalEngCD/VCDDISCOPERATIONTRACK NO.ELAPSED TIMECHAPTER NO.ANGLE NO.A KIND OF AUDIODISC OPERATION TITLE NO.ELAPSEDTIMETOTALTIMETOTALTIMEOUTPUT SELECTIONTimer Recording indicator (VCR)Multifunctional indicatorRecordingindicator (VCR)Track indicator (CD)Tape loaded indicator (VCR)Play indicatorVCR indicator (VCR) Still indicator Disc inserted indicator (DVD)Disc insertedindicator (CD)AM/PM indicator(AM is not displayed)Progressive indicatorAUDIO LANGUAGESUBTITLE LANGUAGEDisplay windowJ2D81001A (E)p02-13.p65 28/5/04, 1:52 PM11
12IntroductionRemote control* MENU buttonUse the MENU button to display the menu included onmany DVD video discs. To operate a menu, follow theinstructions in “DVD Menu.” 54Identification of Controls (continued)The instructions in this manual describe the functions on the remote control. See the page in   for details.FWDREWSTOPPAUSE/STILLVCRDVD CALLDISPLAYTV/VCR AUDIO SELECTAUDIO ATRSUBTITLEA-B RPTCLOCK/COUNTERSP/SLPPLAY MODECOUNTER RESETANGLEINPUT SELECTPROGRESSIVEINDEX SKIP INDEXSKIPTIMER RECREC/OTROPEN/CLOSEEJECTMARKERSET +SET –CH –CH +TOP MENU RETURNZERO RETURNJUMPMENUVCR MENUSETUP CM SKIPZOOMCANCELENTERPLAY8796543210SLOW+–OPEN/CLOSE button (DVD)42ENTER button23RETURN button58CANCEL button37CLOCK/COUNTER button33CM SKIP buttonZOOM button315450MARKER buttonINPUT SELECT button40PROGRESSIVE button66PAUSE/STILL buttonSLOW buttonVCR DVD selector button2231SP/SLP buttonPLAY MODE button3452AUDIO SELECT buttonAUDIO button395155FWD button3031INDEX + buttonSKIP      button4433A-B RPT button52PLAY button30Channel +/– buttons342459CALL buttonDISPLAY buttonINDEX – buttonSKIP      button4433TIMER REC buttonSET +/- buttons23EJECT button (VCR)29TOP MENU button54VCR MENU buttonSETUP button234756TV/VCR button22ATR buttonSUBTITLE button31COUNTER RESET buttonANGLE button543237REW button30ZERO RETURN buttonJUMP button3250STOP button30REC buttonOTR button3436*MENU button(    /    /    /    )Direction buttons45Direct channelselection buttonsNumber buttons452822) buttonPower (J2D81001A (E)p02-13.p65 28/5/04, 1:52 PM12
13IntroductionOperation• Aim the remote control at the remote sensor and press control buttons tooperate.• Operate the remote control within 30° angle on either side of the remotesensor, up to a distance of Approx. 7 meters.Replace the compartmentcover.Install two “R03/AAA” batteries(supplied), paying attention to thepolarity diagram in the batterycompartment.Slide the battery compartmentcover in the direction of thearrow.Approx. 7 metersBattery precautionsThe precautions below should be followed when using batteries in this device:1. Use only the size and type of batteries specified.2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Re-versed batteries may cause damage to the device.  To avoid a potential short circuit, insert the “–” end first.3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury frompossible battery leakage.5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow batterymanufacturer’s directions.)• Press POWER ( ) to turn the DVD VCR on or off.• Select your desired operating mode (DVD or VCR) using VCR DVD.(DVD or VCR indicator on the front panel will show you which mode is selected.)• Press CH + or CH – to move through the channels one channel at a time.• The CH +/– (/ ) and SET +/– ( / ) are also used to navigate on-screen menu system.• You can directly access specific channels using Number buttons.• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and theDVD screen (DVD mode).123Remote control basicsInserting batteriesJ2D81001A (E)p02-13.p65 28/5/04, 1:52 PM13
14ConnectionsOUT(TV)IN(ANT)OUT(TV)IN(ANT)OUT(TV)IN(ANT)Notes: •A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna tothe DVD/VCR properly.•For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor typeantenna is required.•If you are not sure about the connection, please refer to qualified service personnel.The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV andconnect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antennasystem to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs andone 75 ohm output.Note:Combination VHF/UHF Antenna with 75 ohm Coaxial CableCombination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) WireSeparate VHF and UHF AntennasDVD/VCRVHF UHF300 ohm Twin Lead (Flat) Wire(not supplied)Matching Transformer 300 ohm Input 75ohm output (not supplied)300 ohm Twin Lead (Flat) Wire(not supplied)75 ohm Coaxial Cable75 ohm Coaxial CableCombiner 75/300 ohm Inputs 75 ohm output(not supplied)DVD/VCRDVD/VCRAntenna connectionsIf you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead to page 16 forthe proper connections.Antenna to DVD/VCR connection123J2D81001A (E)p14-17.p65 28/5/04, 1:52 PM14
15ConnectionsUHFVHFUHFVHFVHF/UHF INNote: If a VHF or UHF antenna is used,set the TV/CABLE menu option tothe “TV” mode.Note: If a VHF or UHF antenna is used,set the TV/CABLE menu optionto the “TV” mode.Note: If a VHF or UHF antenna is used,set the TV/CABLE menu option tothe “TV” mode.75 ohm Coaxial Cable (supplied)Splitter 75 ohm Input75/300 ohm outputs(not supplied)Splitter 75 ohm Input300 ohm outputs(not supplied)TV with single 75 ohm VHF/UHF antennainputTV with 300 ohm UHF and 75 ohm VHFantenna inputsTV with 300 ohm UHF and 300 ohm VHFantenna inputsAfter you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow theconnection diagram.This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antennainputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.TVTVTV75 ohm Coaxial Cable(supplied)75 ohm Coaxial Cable(supplied) DVD/VCR to TV connectionJ2D81001A (E)p14-17.p65 28/5/04, 1:52 PM15
16ConnectionsCable TV connectionsVHF/UHFIN (ANT)OUT(TV)IN(ANT)VHF/UHFIN (ANT)OUT(TV)IN(ANT)VHF/UHFIN (ANT)OUT(TV)IN(ANT)Many cable companies offer services permitting reception of extra channels including pay or subscription channels. ThisDVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable companysupplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to apremium channel which is scrambled, you must have a descrambler box for proper reception.Allows: *Recording of nonscrambled channels.*Use of the programmable timer.*Recording of one channel while watching another.Allows: *Recording of channels through the converter box(scrambled and unscrambled).*Using the programmable timer to record only thechannel selected at the converter box.Prevents: *Recording one channel while watching another.*Using the DVD/VCR tuner to select channels.DVD/VCRIncoming CableTVConverter/DescramblerIncomingCableTVTVTo record from converter/descrambler,DVD/VCR tuner must be tuned to the con-verter output channel, usually channel 3or 4.Note:DVD/VCRDVD/VCRNote: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output ofthe Converter/Descrambler box, usually channel 3 or 4.Incoming Cable Converter/DescramblerAllows: *Recording of nonscrambled channels.*Use of the programmable timer.*Recording an unscrambled channel while watchingany channel selected at the converter box.Prevents: Recording scrambled channels.If you are playing a tape or using the tunerbuilt into the DVD/VCR, the converter mustbe set to the video channel output of theDVD/VCR (either 3 or 4).Note:123J2D81001A (E)p14-17.p65 28/5/04, 1:52 PM16
17ConnectionsVHF/UHFIN (ANT)ABOUT(TV)IN(ANT)VHF/UHFIN (ANT)ABOUT(TV)IN(ANT)This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scram-bled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Con-sult your local cable company for more information concerning connection to their descrambler equipment. There aremany ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.IMPORTANT: Make sure the TV/CABLE menu option is set to the “CABLE” mode.Incoming CableAllows: *Recording of one channel while watching another.*Using the programmable timer to record only the channel selected at the converter box.*Recording of all channels through the converter box.Prevents: *Watching scrambled channels while recording another channel.*Using the DVD/VCR tuner to select channels.DVD/VCRSplitterConverter/DescramblerTVDVD/VCRConverter/Descrambler A/B SwitchTVIncoming CableSplitterAllows: *Recording of nonscrambled channels.*Recording of one channel while watching another.*Watching premium channels through the converter while recording nonscrambled channels.*Using the programmable timer.Prevents: Recording scrambled channels.DVD/VCRSplitterTVConverter/DescramblerA/B Switch VHF/UHFIN (ANT)ABOUT(TV)IN(ANT)Allows: *Recording of all channels through the converter box.*Recording a scrambled or unscrambled channel while watching another (scrambled orunscrambled) channel.*Using the programmable timer to record only the channel selected at the converter box.Prevents: Using the DVD/VCR tuner to select channels.A/B SwitchIncoming Cable Converter/Descrambler456J2D81001A (E)p14-17.p65 28/5/04, 1:52 PM17
18ConnectionsConnecting to a TV  Connect the DVD/VCR to your TV.To VIDEOOUTTo ANALOG AUDIO OUT(red) (white)(yellow)Signal flowTo wall outletTo video input(yellow) (red) (white)Audio/video cable (supplied)To audio inputsNotes:• Refer to the owner’s manual of the connected TV as well.• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet beforemaking any connections.• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (notsupplied) and then connect to your TV.• Connect the DVD/VCR directly to your TV.  If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector, theplayback picture may be distorted as DVD video discs are copy protected.TV or monitor withaudio/video inputsConnecting to a TVNote: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you   also connect the S-video or ColorStream® component video outputs to your TV/monitor. (See page 19.)J2D81001A (E)p18-25.p65 28/5/04, 1:52 PM18
19ConnectionsNotes:• Refer to the owner’s manual of the connected equipment as well.• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from thewall outlet before making any connections.• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/VCR away from the tuner and radio.• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderatelistening level. Otherwise, the speakers may be damaged by a sudden high volume sound.• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, thespeakers may be damaged.•When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator “” on thedisplay window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot seeany picture. To turn off the Progressive indicator, select PROGRESSIVE scan Off (see page 66).Note: The S-video output and component video output transports the DVD-video signal exclusively and will deliverenhanced DVD video picture performance.If you connect the DVD/VCR to your TVwith the DVD OUT jacks, select thecorresponding video input on yourtelevision to watch DVD video discs.TV or monitor withColorStream®component video inputsTo PR/CR video inputTo PR/CRVIDEOOUTSignal flowTo wall outletTo audio inputs ofthe amplifier(red)(white)(red) (white)To YVIDEOOUTTo PB/CBVIDEOOUTTo Y video inputTo PB/CB video inputAudio systemTo ANALOGAUDIO OUTTo S-VIDEOOUTComponent videocable (not supplied)To S-video inputS-video cable (not supplied)When you make this connection, set the S-VIDEO/COMPONENT Video selector switch to the desiredposition.And also you must select the corresponding videoinput on your TV.Audio cable (not supplied)S-video outputAn S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has S-Video input, and does not have component video inputs.Component video outputsPROGRESSIVE outputsSome TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned videosignal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.INTERLACED outputsSome TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest qualityDVD picture playback.Notes:• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such acase, adjust the TV or monitor for optimum performance.Connecting to an audio system and TV equipped with S-video input/component video inputsJ2D81001A (E)p18-25.p65 28/5/04, 2:27 PM19
20ConnectionsConnecting to optional equipmentYou can enjoy high quality dynamic sounds of DVD video discs oraudio CDs by connecting the DVD/VCR to optional audioequipment.For connection to your TV, see “Connecting to a TV” 18 19.: Front speaker: Rear speaker: Sub woofer: Center speaker: Signal flowConnecting to an amplifier equipped with a Dolby Digital decoderConnecting to an amplifier equipped with Dolby Surround Pro LogicDolby Surround Pro LogicYou can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and leftfront speakers, a center speaker, and one or two rear speakers).Connecting to an amplifier equipped with a DTS decoderDigital Theater Systems (DTS)DTS is a high quality surround technology used in theaters and now available for home use,on DVD video discs or audio CDs.If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTSencoded sound tracks on DVD video discs or audio CDs.Manufactured under license fromDolby Laboratories.  “Dolby” “ProLogic” and the double-D symbol aretrademarks of Dolby Laboratories.• Use DVD video discs encoded viathe Dolby Digital recordingsystem.• Use DVD video discs or audioCDs encoded via the DTSrecording system.* Connect one or two rear speakers.The output sound from the rear speakerswill be monaural even if you connect tworear speakers.“DTS” and “DTS Digital Out” aretrademarks of Digital Theater Systems,Inc.With an amplifier equipped with Dolby DigitalConnect the equipment the same way as described in “Connecting to an amplifierequipped with a Dolby Digital decoder.”  Refer to that amplifier’s owner’s manual and setthe amplifier so you can enjoy Dolby Surround Pro Logic sound.With an amplifier not equipped with Dolby DigitalConnect the equipment as follows.• This connection is only suitable for Video CDs and Audio CDs.Dolby DigitalDolby Digital is the surround sound technology used in theaters showing the latest movies,and is now available to reproduce this realistic effect in the home. You can enjoy motionpicture and live concert DVD video discs with this dynamic realistic sound by connecting theDVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digitalprocessor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit ofPro Logic from the same DVD movies that provide full 5.1-channel Dolby Digitalsoundtracks, as well as from titles with the Dolby Surround mark.Connect either.To OPTICAL typedigital audio inputAmplifier equipped with aDolby Digital decoderOptical digital cable75 Ω coaxial cableTo COAXIALtype digitalaudio inputAmplifier equipped withDolby Surround Pro Logic*Amplifier equipped with aDTS decoderConnect either.To OPTICAL typedigital audio inputOptical digital cableTo COAXIALtype digitalaudio input• This selection uses the following reference mark.To ANALOGAUDIO OUTTo audio inputAudio cable75 Ω coaxial cableJ2D81001A (E)p18-25.p65 28/5/04, 2:27 PM20
21Connections75 Ω coaxial cableOptical digital cable75 Ω coaxial cableWarningWhen playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog stereo jacks. To avoidpossible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of theDVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires dangling.) To enjoyDTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to theBITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.Connecting to an amplifier equipped with an MPEG2 audio decoderMPEG2 soundYou can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier equipped withan MPEG2 audio decoder or MPEG2 audio processor.Connecting to an amplifier equipped with a digital audio input2 channel digital stereoYou can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speakersystem (right and left front speakers).Notes:• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby Digital Receiver.This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIOOUT jack of the DVD/VCR.• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the “OPTICAL” or “COAXIAL” input of a Receiver orProcessor.• Refer to the owner’s manual of the connected equipment as well.• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from thewall outlet before making any connections.• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listeninglevel. Otherwise, the speakers may be damaged by a sudden high volume sound.• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, thespeakers may be damaged.• Use DVD video discs encoded viathe MPEG2 recording system.Amplifier equipped with anMPEG2 audio decoderConnect either.To OPTICAL typedigital audio inputOptical digital cableTo COAXIALtype digitalaudio inputAmplifier equipped with adigital audio inputConnect either.To OPTICAL typedigital audio inputTo COAXIALtype digitalaudio inputJ2D81001A (E)p18-25.p65 28/5/04, 2:27 PM21
22Basic setupSetting the video channelWhen a TV is connected with the 75 ohm coaxial cable only.To view playback of a recorded tape or DVD disc, or to watch aprogram selected by the VCR's channel selector, the TV must be set tochannel 3 or 4 (video channel).Setting the video channelPress POWER to turn on the DVD/VCR.Press VCR DVD selector to select the VCR mode.Turn ON the TV and set to CH 3 or 4 to corre-spond with the channel selected in step 1.Press TV/VCR to select the VCR position.Select any channel to receive a TV station in your area.The channel number will appear on the screen forabout 4 seconds.1The VCR indicator on thefront panel will light.23456The VCR indicator willappear in the displaywindow.For a push-button TV tunerIf CH 3 or 4 corresponding to the video channel cannotbe tuned on your TV, proceed as follows: set the VCR3/4 channel selector and the TV to CH 3 or 4, playback a prerecorded tape and tune the TV to receive asharp color picture from the video cassette recorder.Refer to your TV owner's manual for details.Note:If the unit does not operate properly, or No key operation(by the unit and/or the remote control): Static electricity, etc.,may affect the player's operation. Disconnect the AC power cordonce, then connect it again.POWERVCR DVDTV/VCRPress and hold 3 or 4 on the remote for 3seconds in standby mode.The video channel willstart to flash for 3seconds in the displaywindow.34ORVCRDVDTV/VCR34J2D81001A (E)p18-25.p65 28/5/04, 1:52 PM22
23Basic setupPress SET + or – to select “LANGUAGE”, thenpress ENTER.Press VCR MENU.The VCR menu screen will appear.Press SET + or – to select “SYSTEMSETUP”, then press ENTER.If you use the unit for the first time andpress VCR MENU, instead of the mainmenu screen the “SYSTEM SETUP”menu screen in step 2 may appear.Setting the languageSetting the languageYou can choose from three different languages (English,French and Spanish) for the on-screen displays.12Press SET + or – to select the desired language:English (ENGLISH), Spanish (ESPAÑOL) orFrench (FRANCAIS), then press ENTER.3Press VCR MENU until the MENU screen iscleared.4MENUTIMER REC SETAUTO REPEAT ON OFFON OFFSAPCH SETUPSYSTEM SETUP⟨+/-/ENTER/MENU ⟩SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFFON OFF⟨+/-/ENTER/MENU ⟩⟨+/-/ENTER/MENU ⟩ENGLISHFRANCAISESPAÑOLLANGUAGE/IDIOMA/LANGUENotes:• Both the VCR and the DVD have their own player menus 57.• If no buttons are pressed for more than 60 seconds, the VCRMENU screen will return to normal TV-operation automatically.Preparation:• Turn ON the TV and select to the correspondingvideo input.• Press VCR DVD selector to select the VCR mode.(The VCR indicator will light.)1–31,4VCR DVD1–3VCR MENUSETUPSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERVCR MENUSETUPJ2D81001A (E)p18-25.p65 28/5/04, 1:52 PM23
24Basic setupConnect the Antenna or Cable system.• If you use a cable box, turn it on.Clock settingThe AUTO CLOCK function will automatically set the built-in clock(Month, Day, Year and Time) when the DVD/VCR is connected to anAntenna or Cable system and it is turned off. The DVD/VCR searches fora station in your area containing the necessary AUTO CLOCK settingsignals. Once received, it will take approximately 4 minutes for the clockto set itself automatically.Preparation:• Turn ON the TV and select the corresponding video input.• Press VCR DVD selector to select the VCR mode.(The VCR indicator will light.)1AUTO CLOCK settingPlug the AC Power cord to the AC outlet.2Make sure the DVD/VCR is turned off.• If you press POWER, the Auto Clock   set is not programmed.3Wait at least three minutes and pressPOWER.4Press CALL to check the clock setting onthe on screen display.5If the clock is not set, check the antennacondition. The AUTO CLOCK may notfunction properly if the reception conditionis not good.6AUTO CLOCK adjustmentTo set AUTO CLOCK to offThe auto clock adjustment will be updated at 6:00AM, 12:00 PM and 6:00 PM everyday when theDVD/VCR turned off.• If you use a cable box and you want AUTO CLOCKadjustment to be performed, the cable box must beleft on.• The AUTO CLOCK adjustment is not effective whenthere is a difference of more than 5 minutes existsbetween the built-in clock time and the actual time.When shipped from factory the AUTO CLOCK is set to “ON”.But if you do not want AUTO CLOCK setting:Press VCR MENU.1Press SET + or – to select “SYSTEM SETUP”,then press ENTER.2Press SET + or – to select “AUTO CLOCK”.3Press ENTER to select “OFF”.4Press VCR MENU repeatedly to return to thenormal screen.• When the AUTO CLOCK is set to“OFF”, the AUTO CLOCK adjust-ment does not function.• Set the clock manually 26.5CH  1258 : 47AM   MON00 : 00 : 00  SPSTEREO  SAPMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATSYSTEM SETUPONON OFFOFFCLOCK SETNO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIME+/–/ENTER/MENULANGUAGE/IDIOMA/LANGUESYSTEM SETUPONON OFFOFFCLOCK SETNO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIME+/–/ENTER/MENULANGUAGE/IDIOMA/LANGUEMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATPOWER2,32,41,5CALLVCR DVDCALLDISPLAYVCR MENUSETUPVCR MENUSETUPSET +SET –CH –CH +ENTERSET +CH –CH +ENTERSET –SET +SET –CH –CH +ENTERJ2D81001A (E)p18-25.p65 28/5/04, 1:52 PM24
25Basic setupMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATPress VCR MENU.1Press SET + or – to select “SYSTEM SETUP”,then press ENTER.2Press SET + or – to select “STANDARD TIME”,then press ENTER.3Press SET + or – to select your time zone,then press ENTER.4Press VCR MENU twice to return to thenormal screen.5In the rare event that you live within broadcast range of twostations in two different time zones, the DVD/VCR mayrecognize the wrong station for the AUTO CLOCK setting.To correct the situation:Notes:• To be able to select the standard time, the clock must first beset by AUTO CLOCK once.• If you live in Newfoundland and the AUTO CLOCK does notfunction properly, set the AUTO CLOCK menu option to “OFF”and set the clock manually.Press VCR MENU.Press SET + or – to select “SYSTEM SETUP”,then press ENTER.1Press SET + or – to select “DAYLIGHTSAVING TIME”, then press ENTER.2Press SET + or – to select one of theoptions, then press ENTER. Press VCRMENU until the MENU screen is cleared.3Notes:• When shipped from factory, the DAYLIGHT SAVING TIME isset to “AUTO” position.• When the clock is not set, DAYLIGHT SAVING TIME settingis not available.• When there is no DAYLIGHT SAVING TIME in your area, al-ways select “OFF” position in step 3.When you want to set the DAYLIGHTSAVING TIME manually, on the firstSunday in April you set to “ON”, andon the last Sunday in October you setto “OFF”.ON:OFF:AUTO:for manual setting(forward one hour)for manual setting(back one hour)for automatic setting(read XDS in the signal)DAYLIGHT  SAVING  TIMEONOFFAUTO⟨+/-/ENTER/MENU ⟩ATLANTIC : GMT–4hoursEASTERN : GMT–5hoursCENTRAL : GMT–6hoursMOUNTAIN : GMT–7hoursPACIFIC : GMT–8hoursALASKA : GMT–9hoursHAWAII : GMT–10hoursAUTO : AUTO SET(GMT: Greenwich Mean Time)MENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATSYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFFON OFF⟨+/-/ENTER/MENU ⟩SYSTEM SETUPONON OFFOFFCLOCK SETNO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIME+/–/ENTER/MENULANGUAGE/IDIOMA/LANGUETo set DAYLIGHT SAVING TIMEYou can set the DAYLIGHT SAVING TIME automatically ormanually.To set STANDARD TIMEVCR MENUSETUPVCR MENUSETUPSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERVCR MENUSETUPSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERVCR MENUSETUPSET +SET –CH –CH +ENTERJ2D81001A (E)p18-25.p65 28/5/04, 1:52 PM25
26Basic setupCANCELPress VCR MENU.   EXAMPLE: Setting the clock to “8:30 AM” September,24 (FRI), 2004.18 : 30AM   FRIManual clock settingAfter setting the clock, date and time startsfunctioning automatically.6Note:After a power failure or disconnection of the power, the timersettings will be lost. In this case, reset the present time.To make corrections any time during the processPress CANCEL repeatedly until the item you want tochange blinks, then press SET + or –.Press SET + or – to select “SYSTEM SETUP”,then press  ENTER.2Press SET + or – to select “CLOCK SET”,then press  ENTER.3Press SET + or – to set the month, then pressENTER.4Set the day, year and time as in step 4.5⟨+/-/ENTER/MENU ⟩SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFFON OFFMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATClock setting (continued)If the AUTO CLOCK process did not set the date and time correctly,you must set them manually for timer recording and DAYLIGHTSAVING TIME.2–41⟨+/–/ENTER/CANCEL/MENU ⟩MONTHDAYYEARTIME  91 (WED)200412 : 00AM⟨+/–/ENTER/CANCEL/MENU ⟩MONTHDAYYEARTIME  924 (FRI)20048 : 30AMVCR MENUSETUPSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTER2–4J2D81001A (E)p26-31.p65 28/5/04, 1:52 PM26
27Basic setupTuner settingThis DVD/VCR is equipped with a channel memory feature which allowschannels to skip up or down to the next channel set into memory,skipping over unwanted channels. Before selecting channels, they mustbe programmed into the DVD/VCR’s memory. In addition to normalVHF and UHF channels, this DVD/VCR can receive up to 113 CableTV channels. To use this DVD/VCR with an antenna, set the TV/CABLEmenu option to the TV mode. When shipped from the factory, this menuoption is in the CABLE mode.Press VCR MENU. Press SET + or – to select“CH SETUP”, then press ENTER.1Press SET + or – to select “TV/CABLE”.2CH SETUPTVADD/DELETECABLE+/–/ENTER/MENUAUTO CH MEMORYMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATTV/CABLE selection Setting channels automaticallyRepeat left step 1 and press SET + or – toselect “AUTO CH MEMORY”.1Press ENTER.Auto tuning will begin. The channel dis-play will count up and when finished,the screen returns to normal.2CH 002Note:You can’t select “CH SETUP” if you set the channel to “L1” or“L2”.Press ENTER to select the TV or CABLEmode.The arrow indicates the selected mode.3Press VCR MENU until the menu screen iscleared.4TV - VHF/UHF channelsCABLE - Cable TV channelsCH SETUPTVADD/DELETECABLE+/–/ENTER/MENUAUTO CH MEMORY1,21,31,4CH SETUPTV     CABLEAUTO CH MEMORYADD/DELETE⟨+/-/ENTER/MENU ⟩VCR DVDVCR MENUSETUPSET +SET –CH –CH +ENTERSET +CH –CH +ENTERSET –SET +SET –CH –CH +ENTERVCR MENUSETUPSET +CH –CH +ENTERSET –SET +SET –CH –CH +ENTERPreparation:• Turn ON the TV and select to the correspondingvideo input.• Press VCR DVD selector to select the VCR mode.(The VCR indicator will light.)J2D81001A (E)p26-31.p65 28/5/04, 1:52 PM27
28Basic setupRepeat the step 1 on page 27. Then press SET +or – to select the “ADD/DELETE” and pressENTER.1To ADD/DELETE channelsPress VCR MENU until the menu screen iscleared.3To Add or Delete desired channels2CH SETUPTVADD/DELETECABLE+/–/ENTER/MENUAUTO CH MEMORYADD CH  003+/–/0–9/ENTER/MENU0879654321Press Number buttons or SET + or – to selecta channel number you want to add or delete.To add channelsPress ENTER until “ADD” appears on thescreen.To delete channelsPress ENTER until “DELETE” appears on thescreen. The channel number will blink.12Repeat       to       to add or delete other channel.31 2Tuner setting (continued)Noise eliminationWhen you don't want to receive a weak signal broadcast, aBlue back screen can be obtained by selecting the NO NOISEBACKGROUND “ON”. When the unit is shipped from the fac-tory, the NO NOISE BACKGROUND is set to “ON”.Repeat the steps 1~2 on page 26 and pressSET + or – to select “NO NOISEBACKGROUND”.1Press ENTER to select “ON” or “OFF” position.2SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDON OFFAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFF⟨+/-/ENTER/MENU ⟩Press VCR MENU until the menu screen iscleared.3NUMBER BUTTONS1,231,2SYSTEM SETUPCLOCK SETLANGUAGE/IDIOMA/LANGUENO NOISE BACKGROUNDON OFFAUTO CLOCKSTANDARD TIMEDAYLIGHT SAVING TIMEON OFF⟨+/-/ENTER/MENU ⟩VCR MENUSETUPSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERSET +CH –CH +ENTERSET –SET +SET –CH –CH +ENTERVCR MENUSETUPJ2D81001A (E)p26-31.p65 28/5/04, 1:52 PM28
29Basic setupLoading and unloading a cassette tapeUse only video cassette tapes marked   and  .LoadingRemove the erase prevention tab with a screwdriver. Cover the hole with a piece of adhesive tape.To record againScrewdriverAutomatic tape ejectThis DVD/VCR will automatically rewind the tape when the tape has ended. Once the tape is rewound to its beginning,the cassette tape will be ejected automatically.Press EJECT on the front panel or on the Remote.Push the center of the tape until it is automaticallyinserted.Insert the cassette tape with its labeled side facing upand the erase prevention tab positioned at your left. Aninverted cassette tape cannot be inserted.Automatic playbackWhen loading a cassette tape without an erase prevention tab, playback will start automatically.Automatic power ONWhen you insert a cassette tape the DVD/VCR power will turn ON automatically.12Erase prevention tabAdhesive tapeRemove the cassette tape.Erase prevention tabUnloadingTo prevent accidental erasureTo prevent accidental erasureTape speed and maximum recording timeVideo cassette tapeTape SpeedSLP (Super Long Play)T-160 T-120 T-90 T-60 T-302-2/3 hours 2 hours 1-1/2 hours 1 hour 30 minutes8 hours 6 hours 4-1/2 hours 3 hours 1-1/2 hoursSP (Standard Play)Playback (VCR)EJECTPlayback (VCR)J2D81001A (E)p26-31.p65 28/5/04, 1:52 PM29
30Playback (VCR)Cassette tape playbackTo play a prerecorded tape.Load a prerecorded tape(When loading a cassette tape without the eraseprevention tab, playback will start automatically).Preparation:• Turn ON the TV and select the corresponding video input.• Press VCR DVD selector to select the VCR mode.(The VCR indicator will light).1Press PLAY.Playback will start. “ ” will appearon the screen for about 4 seconds.Press STOP once.The tape will stop but remain fullyloaded and ready to play.“   ” will appear on the screen forabout 4 seconds.To stop playbackStop the playback or recording via STOP on remote.To discontinue the tape-winding, press STOP. To switch toplayback directly (without STOP), press PLAY.Notes:• This VCR selects the playback tape speed SP, LP or SLP au-tomatically.• The Cassette tape and DVD disc can be played back simulta-neously. If you press VCR DVD selector, the tape playbackand DVD playback alternate with each other on the screen(via CH3, 4 or video connection).2To start playbackPlayback Rewind or forward the tapeTo rewind the tape:                               Press REW.To forward the tape:                                 Press FWD.Forward/Reverse picture search modeWhen the tape is being winded, you can switch to picturesearch mode (see next page). To do this, press REW orFWD and hold it down. The unit will resume the tapeadvance or rewinding as soon as the button is released.PLAYSTOPFWDREWVCR DVDPLAYSTOPFWDREWJ2D81001A (E)p26-31.p65 28/5/04, 1:52 PM30
31Playback (VCR)Special playbackPicture searchReverse picture search functionPress REW once or twice during playback.Forward picture search functionPress FWD once or twice during playback.To return to playback, press PLAY.Press PAUSE/STILL during playback.To resume normal playback, press PLAY or PAUSE/STILL.During playback press SLOW.To return to playback, press PLAY or SLOW.Whenever you insert a tape and start playback, theautomatic tracking feature continuously analyzes the signalto enable optimum picture quality during playback.Press PAUSE/STILL during playback.Press SLOW repeatedly: The picture advances frame byframe.To return to playback, press PLAY or PAUSE/STILL.   Slow tracking and vertical lock adjustmentIf noise bars appear in the picture during slow motion,press the SET + /– to reduce the noise bars.If the still picture jitters excessively, press SET +/– tostabilize the still picture.Automatic tracking adjustmentIf automatic tracking cannot eliminate noises well duringplayback, press SET +/– to eliminate the noise. “MANUALTR.” will appear on the screen. Press it briefly for a fineadjustment, or press and hold for a coarse adjustment.Manual tracking adjustmentSPEED SEARCH TIMESAdjusting tracking conditionStill pictureSlow motionFrame by frame pictureNotes:•The audio output is muted during SPEED SEARCH, STILL,FRAME ADVANCE and SLOW MOTION.• During picture search mode there will be noise bars. This isnot a defect.• Playback will commence after approx. 5 minutes to protectthe video tape against excessive wear during pause mode.Press ATR to reactivate automatic tracking again.“AUTO TR.” will appear on the screen.AUTO TR.PICTURE SEARCH SPEEDPRESS TWICETAPE SPEED PRESS ONCESP (Standard Play)LP (Long Play)SLP (Super Long Play)5 X9 X15 X3 X7 X9 XREWPLAYFWDSLOWATRSET +/–PAUSE/STILLVideo head cleaningVideo head clogging The video heads are the means bywhich the DVD/VCR reads the picturefrom the tape during playback. In theunlikely event that the heads becomedirty enough to be clogged, no picturewill be displayed. This can easily bedetermined if, during playback of aknown good tape, there is good sound,but no picture (picture is extremelysnowy). If this is the case, have theDVD/VCR checked and cleaned byqualified service personnel.Notes:•DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS ORSERVICE THE UNIT BY REMOVING THE REAR COVER.•Video heads may eventually wear out and should be re-placed when they fail to produce clear pictures.•To help prevent video head clogging, use only good qual-ity VHS tapes. Discard worn out tapes.Good PictureSnowy PictureCM skipPress CM SKIP during playback. The DVD/VCR will searchforward through approximately 30 seconds of the tape (e.g.unwanted commercial time) for each press of CM SKIP(maximum six presses) and then resume normal playback.For example : 1 press: 30 seconds of tape2 press: 60 seconds of tape3 press: 90 seconds of tapeCM SKIPJ2D81001A (E)p26-31.p65 28/5/04, 1:52 PM31
32Playback (VCR)Convenience functionTo cancel repeat mode:Follow the above step 1, then press ENTER to select“OFF” position. Press VCR MENU to return to the TV.Press VCR MENU.                        Press SET + or – to select “AUTO    REPEAT”.1Press ENTER to select “ON” or “OFF”.If “ON” is selected, the playbackwill be repeated endlessly.2Press VCR MENU until the menu screen iscleared.                        If you press CALL, “ ” will                         appear on the screen 11.3To commence playback, press PLAY.                        The playback will be repeated                         endlessly.4MENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATThis function rewinds the tape to the “00:00:00” counter positionautomatically.Press CLOCK/COUNTER.The counter display shows the tape run-ning time during playback or recording.1Press COUNTER RESET at the desired tapeposition.The counter display will be reset to“00:00:00” position (e.g. the beginningof recording).2Press STOP when playback or recording iscompleted.Press ZERO RETURN.The tape will automatically rewind or fastforward to the “00:00:00” counter posi-tion.3Repeat playbackThe entire video tape will play until its end. The tape willautomatically rewind to the beginning and the playback willbe repeated.MENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATZero return functionCOUNTER RESETPLAYVCR MENUSET +/–ENTERSTOPZERO RETURNCLOCK/COUNTERVCR MENUSETUPSET +CH –CH +ENTERSET –SET +SET –CH –CH +ENTERVCR MENUSETUPPLAYCLOCK/COUNTERCOUNTER RESETANGLESTOPZERO RETURNJUMPCALLJ2D81001A (E)p32-37.p65 28/5/04, 1:53 PM32
33Playback (VCR)This function enables you to locate the beginning of any recordingmade on the VCR.Recording an INDEX markThe Index Search function auto-matically records an INDEX markon the tape whenever a recordingis initiated.Index searchPress INDEX + or – during stop or play mode.For Succeeding programs: Press INDEX +.For Preceding programs: Press INDEX –.(As many as 9 index points can be accessed via thismethod.)When the INDEX + or – is pressed,the unit starts searching the INDEXNO. selected and finds the portion,then playback starts automatically.To stop the Index Search, pressSTOP.CH  001INDEXSQPB (S-VHS Quasi Playback)You can playback video cassette tapes recorded in theS-VHS system.However, the picture will not have the high resolution ofS-VHS system.Note: You cannot record S-VHS video format with this VCR.Notes:• When you record an INDEX mark at the very beginning of thetape, the mark may not be found.• During INDEX search, the tape may stop and begin to play at aslightly different location.• INDEX may not function properly with old or worn out video tapes.• INDEX marks may not be found if it is extremely close to the pointwhere the search began.• In recording, if you stop recording temporarily, the INDEX markis not recorded on the tape.Video index search systemPress CLOCK/COUNTER. The clock and tape counteralternate with each other in the display window.Notes:• If you rewind the tape beyond “00:00:00”, a minus sign (“–”)will be displayed in front of the time.• When you load a tape, the counter will reset to “00:00:00”.• The counter does not function on nonrecorded (blank)sections of the tape. When you rewind, fast forward or playtapes through blank sections, the counter stops.Clock/counter displayCOUNTERCLOCKPress VCR DVD selector. The DVD mode and theVCR mode alternate with each other in the display.DVD modeVCR mode+3INDEX NO. (up to 9)or      is displayedSTOPVCR DVDINDEX +/–CLOCK/COUNTERCLOCK/COUNTERINDEXSKIP–INDEXSKIP +STOPVCRDVDJ2D81001A (E)p32-37.p65 28/5/04, 1:53 PM33
34Recording (VCR)Recording a TV programRecording and viewing the same TV program.Recording a TV programLoad a cassette tape with the erase preventiontab intact.                     The DVD/VCR will automatically turn on.100 : 00 : 00  SPCH  110CH  110INDEXPress SP/SLP to select the desired tape speedSP or SLP.The tape counter and “SP” or “SLP”will appear on the screen for about 4seconds.2Select “TV” or “CABLE” to the appropriateposition 27.3TV - VHF/UHF channelsCABLE - Cable TV channelsPress Number buttons or CH +/– to select thechannel to be recorded.4Press REC/OTR.                       “   ” will appear on the screen                     for about 4 seconds and “REC” will                         appear on the display window.5VHF/UHF/CABLE TV CHANNELSTV CABLE TVVHF2-13UHF14-69VHF2-13STD/HRC/IRC 14-36   (A) (W) 37-59  (AA) (WW)    60-85   (AAA) (ZZZ)  86-94   (86) (94) 95-99   (A-5) (A-1)100-125  (100)(125)  01  (5A)TV mode direct channel selection:All channels can be instantly selected by using twobuttons. (for example, to select channel 2, press “0”, then“2”. If you press only “2”, channel selection will be delayedfor two seconds.) For channels 10 and above, press the 2digits in order.CABLE mode direct channel selection:1-9 Press 0 twice and then 1-9 as required.Example: To select “2”, Press 002.10-12 Press 0 first and then the remaining 2 digits inorder from left to right.Example: Press 012 for “12”.13-99 Press 2 digits in order.Example: Press 22 for “22”.100-125 Press the 3 digits in order.Example: Press 110 for “110”.08796543214425VCR DVDSP/SLPPLAY MODESET +SET –CH –CH +ENTERREC/OTRPreparation:• Turn ON the TV and select to the correspondingvideo input.• Press VCR DVD selector to select the VCR mode.(The VCR indicator will light.)J2D81001A (E)p32-37.p65 28/5/04, 1:53 PM34
35Recording (VCR)Recording one program whilewatching anotherPress STOP to stop recording.                  “   ” will appear on screen for about                                  4 seconds.Press PAUSE/STILL to avoid recording unwantedmaterial. Press again to continue the recording.                                  “ ” will appear on screen for                                  about 4 seconds.Notes:•The pause function will be released after 5 minutes to preventdamage to the tape or the VCR. The VCR will change to theSTOP mode.• You can select a recording channel in the recording pausemode.To stop recording temporarilyWhile the VCR is recording, select your desired channelon the TV.When a TV is connected with an antenna cable only,press TV/VCR to select the TV position.The “VCR” display  will go off and recording will continue.Select the TV channel you want to watch by using theTV channel selector.Note:Some Cable TV hookups do not permit viewing one channelwhile recording another. See pages 16 and 17.This VCR will automatically rewind the tape when the tapehas ended (except during OTR and timer recording). It willalso eject the tape.Auto Rewind featureTo stop recordingTV/VCRSTOPPAUSE/STILLPAUSE/STILLSTOPJ2D81001A (E)p32-37.p65 28/5/04, 1:53 PM35
36Recording (VCR)One-touch Timer Recording (OTR)The One-touch Timer Recording feature provides a simple andconvenient way to make a timed recording.One-touch Timer Recording (OTR)Pressoncetwice3 times4 times5 timesNORMAL REC0:301:001:302:003:004:005:006:00NORMAL RECRecording time Press6 times7 times8 times9 times10 timesRecording timeLoad a cassette tape with the eraseprevention tab intact.    The VCR will automatically turn on.1Press SP/SLP to select the desired tape speedSP or SLP.The tape counter and “SP” or “SLP”will appear on the screen for about 4seconds.2Set “TV” or “CABLE” option to theappropriate position 27.300 : 00 : 00  SPCH  110CH  110INDEXOTR  0 : 30TV - VHF/UHF channelsCABLE - Cable TV channelsPress Number button or CH +/– to select thechannel to be recorded.4Press REC/OTR. Recording begins. Press thebutton again to stop recording after 30 minutes.Each additional press of REC/OTR will increaserecording time as shown in the chart below, upto a maximum of 6 hours.The OTR and recording time willappear on the screen for about 4seconds. And, “   ” will appear onthe display.5To cancel OTRPress STOP or turn off the power.“   ” will appear on screen for about 4 seconds.Note:If you wish to watch the DVD playback during OTR or standardrecording, press VCR DVD selector to change to DVD mode andperform the DVD playback 43.4425VCR DVDSTOP0879654321SP/SLPPLAY MODESET +SET –CH –CH +ENTERREC/OTRSTOPPreparation:• Turn ON the TV and select to the correspondingvideo input.• Press VCR DVD selector to select the VCR mode.(The VCR indicator will light.)Example: One-touch Timer Recording for 30 minutes.J2D81001A (E)p32-37.p65 28/5/04, 1:53 PM36
37Recording (VCR)Timer recordingTimer recording can be programmed on-screen with the remote control.The built-in timer allows automatic unattended recording of up to 8programs within 1 month.Timer recordingNotes:• Press CANCEL to move cursor backward for correction.• To record from external source set the channel to “L1” or“L2”.Notes:• If the timer symbol ( ) blinks when the timer recording ended,the TV program has not been completely recorded because ofan insufficient tape length. Press TIMER REC to cancel thetimer program or press EJECT to remove the cassette tape.• During timer recording standby mode, the VCR mode cannot beoperated. To use the VCR, press TIMER REC at first, then pressVCR DVD selector to change to VCR mode. After you use theVCR, press TIMER  REC again to put the VCR into timerrecording standby mode.• If you press TIMER REC during timer recording, the recordingoperation will be interrupted. If you press TIMER REC againwithin the programmed time, the recording operation will startagain.• After a power failure or disconnection of the power plug, allprogrammed recording settings and time display will be lostupon resumption of power. In this case, reset the clock 24 andreprogram any timer recording.Press VCR MENU. Select “TIMER REC SET”,then press ENTER.Preparation:• Press VCR DVD selector to select the VCR mode.• Load a cassette tape with the erase prevention tabintact.• Check the time and date are correct 24.Example: Program a timer recording for the 26th day,channel 125 (Cable TV), 11:00 - 11:30 PM on timer programnumber 1 (Tape speed: SLP).1Press SET + or – to select one of the programline, then press ENTER.2Press SET + or – to select the date, then pressENTER.3Set the start time, end time, channel and tapespeed as in step 3.4MENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEAT⟨+/–/ENTER/CANCEL/MENU ⟩DATE START END CH–––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––––26(SU)11:00PM11:30PM125SLP⟨+/–/ENTER/CANCEL/MENU ⟩DATE START END CH–––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––––26(SU)11:00PM11:30PM125SLPTo enter other programs, repeat step 2through 4.• To return to the normal screen,press VCR MENU twice.5Press TIMER REC. The timer symbol ( ) willappear on the display and the VCR stands byfor recording.At the same time, VCR mode willchange to DVD mode automatically.You can use DVD even if the VCR isin the timer recording mode.If you do not use the DVD, turn thepower off.6Notes:• The timer recording will start at 5 seconds before the timeyou predetermined.• If the timer symbol(   ) does not appear on the display inspite of the pressing of TIMER REC, the cassette may nothave been loaded.29• If the cassette is ejected in spite of the pressing of TIMERREC, the erase prevention tab of the cassette may havebeen removed.292,31–3VCR DVDTIMER RECCANCEL1,5EJECT⟨+/–/ENTER/CANCEL/MENU ⟩DATE START END CH–––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– –––––––––––⟨+/–/ENTER/CANCEL/MENU ⟩DATE START END CH–––––– –:–– –:–– ––––:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––––– 26(SU)SET +SET –CH –CH +ENTERVCR MENUSETUPSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERVCR MENUSETUPTIMER RECJ2D81001A (E)p32-37.p65 28/5/04, 1:53 PM37
38Recording (VCR)Setting procedureTo set daily/weekly timerTo confirm Timer program:At step 1 on the previous page select “TIMER RECSET” and press ENTER.The timer program list will appear on the screen.2The current day (Friday) SU-SA (Sunday to Saturday)MO-SA (Monday to Saturday)MO-FR (Monday to Friday)WKL-WE WKL-TH (Weekly Thursday)(Weekly Wednesday)One month laterminus one dayWeekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-SA: Monday to Saturday) Timer recordingFollow the procedure of timer recording on the previouspage. At step 3 press SET + or – repeatedly until thedesired setting appears. Then press ENTER.When you press SET – repeatedly, theDATE indicator will change as follows, inthis case the day is Friday.If the programs overlap anotherDo not overlap timer programs as portions of theconflicting programs will be lost. The first recordingtime has priority over the next recording time as shownin the diagram below.Notes:• The daily/weekly recording can be made continuously until therecording is canceled or the tape reaches the end.• During timer recording the automatic rewinding mechanismdoes not function.8 : 00 11 : 009 : 00 10 : 00Program 1Prog.1Deleted PartsNon Recorded Portion PartsProg.2 Prog.3Program 2Program 3Recording Control Settings⟨+/–/ENTER/CANCEL/MENU⟩DATE START END CH WKL-WE⟨+/–/ENTER/CANCEL/MENU⟩DATE START END CH26(SU)11:00PM11:30PM125SLPNotes:• If there are other timer record programs remaining, TIMERREC must be pressed to reactivate the timer, otherwise theremaining timer record programs will be ignored.• You cannot confirm the Timer program during timer recordingoperation.• You can correct or cancel a programmed setting in programconfirm mode.If the Timer has been activated, press TIMERREC to deactivate the Timer.The timer symbol ( ) willdisappear. Then press VCR DVDselector to change to VCR mode.1To cancel Timer program:Press SET + or – to select the unwanted program,then press CANCEL to cancel the program.3Press VCR MENU repeatedly until the menuscreen is cleared.4Timer recording (continued)To confirm or cancel a programSET +/–ENTERVCR MENUCANCELVCR DVDTIMER REC⟨+/–/ENTER/CANCEL/MENU ⟩DATE START END CH–––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– ––––––––– –:–– –:–– –––––––––––TIMER RECVCR MENUSETUPSET +SET –CH –CH +ENTERSET +SET –CH –CH +ENTERSET +CH –CH +ENTERSET –CANCELVCRDVDJ2D81001A (E)p38-41.p65 28/5/04, 1:53 PM38
39Other functions (VCR)Stereo recording and playback /Second Audio Program (SAP)When a MTS STEREO broad-cast is received, “STEREO” willappear on the screen for about 4seconds and the program canbe viewed or recorded in stereo.The Hi-Fi stereo recording pro-cedure is the same as for normalrecordings.Notes:• When playing back a tape that is not recorded in Hi-Fi stereomode, the audio will automatically be monaural.• When listening to a VHS Hi-Fi video tape or MTS broadcastthrough the VHF/UHF jack (Audio/Video cable not connected),the sound will be monaural.When viewing an MTS stereo TV program, or playing aprerecorded VHS Hi-Fi stereo videotape, press AUDIOSELECT to select how the audio will be heard throughthe speakers. Normally set to the Hi-Fi stereo position,this button can be set to the MONO position if the stereobroadcast or videotape audio is of poor quality. The “R”and “L” positions allow the audio from the Right or Left Hi-Fi channel to be heard over both TV speakers. Thisbutton has no effect when viewing a MONO videotape orTV program. Each time when you press the button,OUTPUT SELECTION display appears on the screen forseveral seconds. Refer to the chart below.Output selectionYour DVD/VCR is fitted with a SAP broadcast system whichenables you to switch to a second audio program whenviewing a selected channel.This function applies only when the program is broadcastin multi-languages through the SAP broadcast system.When the VCR is turned on or a channel selection ismade, make certain the letters “SAP” appears on thescreen for about 4 seconds. This means that the “SecondAudio Program” broadcasting is available.Listening to SAPStereo recording and playbackThe VHS Hi-Fi audio system permits high fidelity record-ing of MTS STEREO TV broadcasts.Second Audio Program (SAP)OUTPUTSELECTIONSTEREOL CHR CHMONOSOUND HEARD ON BOTHSPEAKERSSTEREOLEFT CHANNEL AUDIORIGHT CHANNEL AUDIOMONOPress VCR MENU. Then press SET + or – toselect “SAP”.1Press ENTER to select “ON”.Then press VCR MENU until themenu screen is cleared.2STEREOSTEREO  SAP SAPMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATORSET +/–ENTERVCR MENUOther functions (VCR)Note:When using a Cable TV system, stereo TV programs maybe transmitted over a mono cable channel. In this case“STEREO” will not appear and the sound will be in mono.AUDIO SELECTMENUONON OFFOFFTIMER REC SETSAPCH SETUPSYSTEM SETUP+/–/ENTER/MENUAUTO REPEATAUDIO SELECTAUDIOSET +SET –CH –CH +ENTERSET +CH –CH +ENTERSET –VCR MENUSETUPVCR MENUSETUPJ2D81001A (E)p38-41.p65 28/5/04, 1:53 PM39
40Other functions (VCR)To AUDIO (L) OUTAUDIO/VIDEO cable (supplied)Playback VCRTo VIDEO OUT To AUDIO (R) OUTRecording VCRTo AUDIO (L) INTo VIDEO IN To AUDIO (R) INDuplicating a video tape       If you connect the DVD/VCR to another VCR or Camcorder, you can duplicate       a previously recorded tape. Make all connections before turning on the power.Duplicating a video tapeFor duplicating a previously recorded tape from acamcorder, follow the camcorder manufacturer’sinstructions. A typical camcorder dubbing hookup isshown above.AUDIO/VIDEO cable (not supplied)To AUDIO (R) INTo AUDIO (L) INTo VIDEO INRecording VCRTo AV JackPlayback CamcorderConnection with second VCRConnection with CamcorderPress SP/SLP to select the desired tape speedSP or SLP.  It is recommended that you set the  tape speed to the SP mode on the  recording VCR for best results.1Press INPUT SELECT once or twice to selectAUDIO/VIDEO input position.                         “L1” or “L2” will appear in the display.2Press REC/OTR on the recording VCR.                         The duplicating process begins.3Press PLAY on the playback VCR or Camcorder.4Press STOP after duplicating a video tape.5L1: on the rear panelL2: on the front panelPreparation:• Turn ON the TV and select the corresponding videoinput.• Press VCR DVD selector to select the VCR mode.(The VCR indicator will light.)• Load a cassette tape with the erase prevention tabintact.• Load a previously recorded tape into the playbackVCR or Camcorder.5142VCR DVDSP/SLPPLAY MODEINPUT SELECTPROGESSIVEREC/OTRSTOPJ2D81001A (E)p38-41.p65 28/5/04, 1:53 PM40

Navigation menu