OSIM OS-322 BT Module for Data Transfer User Manual Specifications of OS322 BT PCBA 1 June 26 2012

OSIM INTERNATIONAL LTD BT Module for Data Transfer Specifications of OS322 BT PCBA 1 June 26 2012

ARG-OS-322_User manual

Specifications of OS-322 MCU Board (Preliminary) 1 HARDWARE Specifications Frequency Band: Support for 802.11 co-existence 2.4GHz ~ 2.48GHz unlicensed band Bluetooth System: v2.1 (Class 2) Antenna: Class 2 power output with printed PCB antenna Power: 3.3V from uSqueez App Power PCBA (2.7V to 3.6V) RF: 1Mbps GFSK. Interfaces : 7 connectors – CN1 – 5 pins (1 x 5 connector 2.0mm pitch) CN7 – 3 pins (1 x 3 connector 2.50mm pitch) CN9 – 2 pins (1 x 2 connector 2.50mm pitch) CN12 – 9 pins (1 x 9 connector 2.0mm pitch) ISO3 – 7 pins, 2.54mm (1 x 7 connector 2.50mm pitch) J1 – 6pins (1 x 6 connector 2.54mm pitch) J4 – 7 pins, 2.0mm (1 x 7 connector 2.0mm pitch) Limit Safety Switch: A safety limit switch will be connecting to CN9. The safety limit switch is normally close (GND) and makes the uSqueez App working normally. If the safety limit switch is opened (Pull-high), the motors in uSqueez App will stop immediately and output beep sound twice. Optical Sensor: The optical sensor is used to detect the wide and narrow position. It will be connected to CN7. Operating: 0 - 70°C Temperature Range Dimensions: 80mm x 43mm x 8.6mm Indicators: 8 LEDs (on Button PCBs) – Power On/OFF (Color Red) Vibration Hi (Color Red) Vibration Lo (Color Red) Soothe of Auto Mode (Color Red) Pulse of Auto Mode (Color Red) Energize of Auto Mode (Color Red)
Specifications of OS-322 MCU Board (Preliminary) 2 Bluetooth power indictor (Color Red) BT connection status (Color Blue) Buttons: 4 buttons (on Button PCBs) – Power On/OFF Vibration Hi/Lo Auto Mode Bluetooth button Current consumption: 50mA (approx.) Under Industry Canada regulations, this radio transmitter may only operate using anantenna of a type and maximum (or lesser) gain approved for the transmitter byIndustry Canada. To reduce potential radio interference to other users, the antennatype and its gain should be so chosen that the equivalent isotropically radiated power(e.i.r.p.) is not more than that necessary for successful communication.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvépour l'émetteur par Industrie Canada. Dans le but de réduire les risques debrouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le typed'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communicationsatisfaisante.Information for the OEMS IntegratorsThis device is intended for OEM integrators only. Please see the full grant of equipment document forrestrictions.Label Information to the End User by the OEM or IntegratorsIf the FCC ID of this module is not visible when it is installed inside another device, then the outside ofthe device into which the module is installed must be labelled with “Contains FCC ID: ARG-OS-322 and IC:10142A-OS322”.
Specifications of OS-322 MCU Board (Preliminary) 3 MECHANICAL SIZE
Specifications of OS-322 MCU Board (Preliminary) 4 CONNECTOR PIN LAYOUT Connector Pin Signal Name Description CN1 (To Push Button PCB - BT) 1 VDD_3V3 3.3V power for LED 2 BT_LED1 Bluetooth LED1 enable / disable 3 BT_LED2 Bluetooth LED2 enable / disable 4 ADC1 Detect Push button according to input voltage level No button press : 0.28×VDD to VDD Bluetooth button: 0V to 0.28×VDD 5 KEY_DET Push button press detect CN7 (To Optical Sensor) 1 SENS_VDD 3.3V Power for Sensor 2 OPT_IN Input signal from Optical Sensor 3 GND Signal Ground CN9 (To Safety Limit Switch) 1 SAFE_DET Safety Limit Switch detection input 2 GND Signal Ground CN4 (To Button PCB - Function) 1 VDD_3V3 3.3V power for LED 2 M_DATA5 LED5 enable / disable 3 M_DATA4 LED4 enable / disable 4 M_DATA3 LED3 enable / disable 5 M_DATA2 LED2 enable / disable 6 M_DATA1 LED1 enable / disable 7 M_DATA0 LED0 enable / disable 8 ADC0 Detect Push button according to input voltage level No button press: 0.90×VDD to VDD Vibration button: 0.59×VDD to 0.90×VDD Power button : 0.28×VDD to 0.59×VDD Program button : 0V to 0.28×VDD 9 KEY_DET Push button press detect ISO3 (To Power PCBA) 1 VDD 3.3V Power supply from power board (2.7 to 3.6V) 2 GND Signal Ground 3 O_BUZZER Buzzer control signal to power board 4 O_MOMI Massage motor control signal to power board 5 O_VIB Vibration motor control signal to power board 6 GND Signal Ground 7 ZERO_CRS Zero cross signal from power board J4 1 GND Signal Ground 2 3V3 Control Signal for MCU firmware upgrade 3 PGM Control Signal for MCU firmware upgrade 4 SDO Control Signal for MCU firmware upgrade 5 RESET Control Signal for MCU firmware upgrade
Specifications of OS-322 MCU Board (Preliminary) 5 6 SDI Control Signal for MCU firmware upgrade 7 SCK Control Signal for MCU firmware upgrade J1 1 BT_3V3 Control Signal for BT module firmware upgrade 2 MOSI Control Signal for BT module firmware upgrade 3 MISO Control Signal for BT module firmware upgrade 4 CSB Control Signal for BT module firmware upgrade 5 CSK Control Signal for BT module firmware upgrade 6 GND Signal Ground Caution:This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) this device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorisée aux deux conditionssuivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur del'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage estsusceptible d'en compromettre le fonctionnement.Changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generatesuses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the followingmeasures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.

Navigation menu