Ocean Star Electronics LP200 Turntable Sound System User Manual TY LP200 1

Ocean Star Electronics Ltd. Turntable Sound System TY LP200 1

User manual

Download: Ocean Star Electronics LP200 Turntable Sound System User Manual TY LP200  1
Mirror Download [FCC.gov]Ocean Star Electronics LP200 Turntable Sound System User Manual TY LP200  1
Document ID3466731
Application IDipu07jd3j7Y2k93DD74pnQ==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize20.53kB (256624 bits)
Date Submitted2017-07-16 00:00:00
Date Available2017-07-16 00:00:00
Creation Date2017-04-23 17:19:35
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2017-07-14 19:28:14
Document TitleMicrosoft Word - TY-LP200 User manual-1
Document CreatorPScript5.dll Version 5.2.2
Document Author: hp

TY‐LP200
USB MP3 DIRECT RECORDING TURNTABLE SYSTEM
Instruction Manual
BOX CONTENTS
Make sure that the items listed below are included in the box:




Main Unit
Power Adapter
Instruction Manual
45 RPM Adapter
READ SAFETY INSTRUCTION BOOK BEFORE USING THE PRODUCT
FUNCTION KEY PANEL
LED INDICATOR
1 USB
2 PHONO
3 BLUETOOTH
4 AUX
5 REC
KEY
6 FUNCTION
7 I<< VR‐ Volume ‐
8 >>I VR+ Volume +
9 PLAY/PAIR
10 STOP/REC
11 USB SOCKET
BACK PANEL
1SPEAKER OUT
2 LINE IN
3LINE OUT
4DC IN 15V 1600mA
5POWERON/OFF
TURNTABLE PANEL
1 TURNTABLE
2 FUNCTIONKEY PANEL
3TRANSIT SCREW CROSSING
4 LIFT LEVER
5 SPEED SELECTOR (33/45/78 RPM)
6 TONE ARM LOCK
7 TONE ARM WITH STYLUS
UNPACKING AND SET UP
1. Carefully remove the unit from the display carton and remove all packing material from the unit.
2. Unwind the AC adapter jack and extend it to its full length.
3. Place the unit on a stable, level surface, convenient to an AC outlet and outside of any strong
magnetic field.
4. Connect the plug to your AC outlet.
5. Remove the opaque white plastic stylus cover from the phonograph stylus by sliding it in the
direction of the arrow.
6. During this operation pay attention to the stylus, because the stylus damage is not covered by
guarantee.
7. Remove the twist‐tie that was used to secure the tone arm during the shipment.
8. Release the tone arm lock level.
9. Clip the speaker cable to the speaker output socket.
POWERING ON THE UNIT
1. Connect the AC adapter to the AC power socket on the back of the unit.
2. Press the Power ON/OFF switch until the indication LED lights up. This will turn the on the unit.
3. When you have finished using the system, press Power ON/OFF button again to turn off the unit.
NOTE
When select a certain function, but without further instruction or signal to the unit during 30 minutes,
the unit will automatically turn off.
LINE IN OPERATION
1. This unit provides aLINE INjack for connecting external audio devices like MP3 players, CD
players and older, non‐dock‐able iPod, so you can listen to your external device through the
speakers of this system.
2. Use an audio cable (not included) with one 3.5mm stereo connection on each end of the cable.
3. Plug one end into the LINE IN jack on the main unit and the other end to the line‐out jack of your
audio device.
4. Power ON both devices.
5. The volume level can be controlled through the main unit.
6. Remove the twist‐tie that was used to secure the tone arm during the shipment.
7. Release the tone arm lock level.
NOTE
1. If the Line OUT jack of our external device is connected, you only need to adjust the volume
control of this system.
2. Make sure tone arm is securely locked to the tone arm lock to avoid any damage.
3. Press Power ON/OFF switch to turn off the unit when you are done. Don’t forget to turn off the
power on your external device as well.
PLAYING RECORDS
This system includes a full‐size, 3‐speed, belt‐drive turntable that plays 33, 45 and 78 RMP records.
1. To turn the system on, press I<< VR‐button to set the volume to a low level.
2. The phone mode was turn on. Please be sure that you have removed the stylus cover from the
stylus and have released the tone arm lock.
3. Set the turntable speed switch to the appropriate speed: 33, 45 and 78 RPM. Set the record
onto the turntable. If you are playing 45 RPM singles, place the 45 RPM adapter on the center
spindle.
4. When you choose play a certain song, move the tone arm to the record. Pull the LIFT LEVER
gently forward to yourself, the tone arm gently lower onto the record. The song will start
playing.
5. When finish playing the song, put the LIFT LEVER gently backward to you, the tone arm gently
lifter onto the record. The song will stop playing.
6. Press the I<< VR‐ Volume ‐/>>I VR+ Volume +to set the volume as desired.
7. Press Power ON/OFF switch to turn off the system when you are done.
8. During record playing, please open the dust cover.
PHONOGRAPH RECORDING OPERATION
1. Place a phone record on the turntable.
2. Plug USB stick into USB socket. Press PHONO‐REC button, the REC LED indication light on. It
starts recording the music from the phone record.
3. Press PHONO‐REC button again when you finish recording.
4. Press USB‐MP3 button with USB LED light is on, you can hear the recording track on the USB
stick.
NOTE
1. PHONE‐REC is only for phonograph recording.
2. PHONO‐REC is for recording the music from the phono record through USB stick device.
USB OPERATION
1. Press FUNCTION button to turn on USB mode with LED indication on.
2. Insert the USB device into the USB input on the system, the player will start playing the tracks on
the USB device.
3. Press the I<>Ibutton to choose our desired track.
4. Press the >II button to pause or play the track.
5. Press the POWER ON/OFF switch to turn off the unit when you are done.
NOTE
1. The USB playing mode has memory function. When inserting the same USB device, it will
resume the play the last track.
2. This unit is equipped with a USB socket that can play MP3 files stored on standard USB flash
(compatible with USB version 2.0)
3. The USB flash with more than 32GB memory may not be compatible.
4. Although this product is fully compatible with USB 2.0 standard formats, a small percentage of
USB flash drivers might not be readable due to those device manufacturers’ non‐compliance
with the full (official) USB standards.
REMOVING HE USB DRIVE
Please be sure to stop playbacks and turn the unit off before removing the USB device to avoid damage
to the USB and the system.
BLUETOOTH OPERATION
1. Press FUNCTION button on the function panel to activate the BLUETOOTH function, and the light
will be flash on.
2. Set up the Bluetooth playback device so it searches for other Bluetooth devices.
3. Select the entry TY‐LP200 from the list of found devices on your Bluetooth playback device. If
the pairing is successful, you will hear a signal with ‘Di’ sound.
4. Enjoy your music from your playback device.
NOTE
1. The next time you turn on the device, it will automatically connect to the last connected
Bluetooth playback device. If your Bluetooth playback does not automatically reconnect to the
device, you will have to re‐establish the connection to your Bluetooth device manually.
2. If you use a smart‐phone as your Bluetooth playback device, the audio file will muted when
there is an incoming call. Acceptance / termination of the call is carried out via the smart phone.
After finishing the call, the playback will be automatically continued.
LINEOUT OPERATION
1. This system includes a set of LINEOUT jack which allow you to play from the BT, USB and
PHONOGRAPH of this system to an external playback device.
2.
3.
4.
5.
Insert the Audio cable (not included) into the matching “LINE OUT” socket of the unit.
Operate the unit as usual.
In order to achieve best effect in sound, advise setting the unit volume into minimum level.
Through the speakers of external playback devices, we can hear the sound exported from the
unit.
REPLACING THE STYLUS
It’s suggested to replace the stylus after playing more than 400 hours.
Please follow below steps to change the stylus:
1. Lift the tone arm off the tone arm lock.
2. At the front end of the tone arm, place the tip of your fingernail between the red stylus holder
and the back cartridge housing as shown, press down on the red stylus holder until it separates
from the cartridge housing.
3. Completely remove the red stylus holder with worn stylus and discard it.
4. Place the new red stylus holder with stylus under the cartridge housing. First, press upward on
the back side of the stylus holder, and then press up on the front edge of the stylus holder until
it snaps into place on the cartridge housing.
5. Through the speakers of external playback devices, we can hear the sound exported from the
unit.
IMPORTANT!
TRANSPORTING THE SYSTEM
1. To protect the turntable from the damage during transportation, a silver transit screw is located
at the upper right the turntable platform.
2. Before playing, please use a screwdriver to turn the transit screw in clockwise direction (screw
going down) completely to unlock the turntable.
3. To lock the turntable again for transportation, please turn screw in counter‐clockwise direction.
CARE OF THE WOOD PANEL AND DUST COVER
1. Care of the unit is the same as any piece of the furniture.
2. When the dust cover is dusty, you may wipe it using soft, non‐abrasive dust cloth.
3. If the wood panel becomes smudged with fingerprints, you may use any good quality
commercial dusting and polishing spray cleaner.
4. We recommend spraying the cleaner on the cloth, not directly on the wooden panel.
CARE AND MAINTENANCE
To replace the cartridge from the tone arm, please follow the procedure below.
1. Gently lift off the tone arm from the tone arm lock.
2. By using your left hand to hold the tone arm and using your right hand to hold the rear portion
of the cartridge. Then push the cartridge backwards and downwards according to the direction
as shown to the left to separate the cartridge from the tone arm.
3. Using either a tweezer or your fingers, carefully unplug the terminals to the new cartridge.
4. Carefully connect the terminals to the new cartridge (not included).
5. To re‐install the new cartridge to the tone arm. First please lock the front end of the new
cartridge on the hook of the tone arm.
6. Press the rear s=ide of the new cartridge upwards to lock it on the tone arm.
CAUTION
Please don’t damage the stylus when installing the new cartridge.
SPECIFICATIONS
Operating voltage
Bluetooth Specification
Supported Storage
Output Power
Dimensions(L*W*H)
DC15V 1600mA
Version 3.0
USB
2 x 10W RMS
343 x 426 x 58
Specifications and functions are subject to change without notice. It is connected with continual
improvement of the device.
FCC Compliance Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
(1)this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
This device has been evaluated to meet general RF exposure requirement. The device can be used in
Portable exposure condition without restriction.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est
soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un
mauvais fonctionnement de l'appareil.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : hp
Create Date                     : 2017:04:23 17:19:35+08:00
Modify Date                     : 2017:07:14 19:28:14+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : hp
Title                           : Microsoft Word - TY-LP200 User manual-1
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:07:14 19:28:14+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:9db9d012-979f-469d-bb51-1975c30da5d4
Instance ID                     : uuid:a94f5382-94cd-4974-8b51-828039a09b78
Page Count                      : 10
EXIF Metadata provided by EXIF.tools
FCC ID Filing: LMZ-LP200

Navigation menu