Ohsung Electronics URCTRFUZ1 Base Station User Manual EMISSION TEST REPORT

Ohsung Electronics Co., Ltd. Base Station EMISSION TEST REPORT

user manual

G Order Number : GETEC-C1-12-307 FCC Part 15 subpart C Test Report Number : GETEC-E3-12-107 Page 1 / 1 EUT Type: Base Station FCC ID.: OZ5URCTRFUZ1 APPENDIX H : USER’S MANUALG
TRF-UZ1 Z ExtenderOwner’s Manual
TRF-UZ1 Z EXTENDER500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 TRF-UZ1 Z Extender Owner's Manual © 2012 Universal Remote Control, Inc.The information in this manual is copyright protected. No part of this manual may becopied or reproduced in any form without prior written consent from UniversalRemote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice. URC - Control the Experience is a registered trademark of Universal Remote Control, Inc.All other brand or product names are trademarks or registered trademarks of theirrespective companies or organizations.
TRF-UZ1 Z EXTENDERCongratulations! 1Features and Benefits 1Parts Guide 1TRF-UZ1 Panel Descriptions 2Specifications 3USA Limited Warranty Statement 4Federal Communication CommissionInterference Statement 6Regulatory Information to the user 7Delaration of Conformity 8
Page 1TRF-UZ1 Z EXTENDERCongratulations!Thank you for purchasing the Total Control TRF-UZ1 Z Extender foruse with an MRX Advanced Network System Controller. This deviceallows for optimal placement of the system’s RF antenna, allowingfor more robust coverage in all corners of the home or small officespace. Designed to work on URC’s 2.4GHz wireless network, thiscompact device works with other devices that use the same networkprotocol, like the MRX-10 Controller, TRC-780 Remote and theTHZ-100 Thermostat. Features and BenefitsReplaces the internal antenna on the MRX-10 to allow foroptimal placement and communication, through the wirednetwork, between devices operating on URC’s 2.4GHznetwork.Using the optional TRF-UZ1 Z disables the internal antenna onthe MRX-10 and uses its own internal antenna as the new“point of origin” for the RF signal. This feature provides anabundance of placement options, minimizes the need for ZRseries repeaters, and ensures a robust signal to auxiliary devices.Adds a 2.4GHz network antenna to the MRX-20 AdvancedNetwork System ControllerWithout an included 2.4GHz antenna, the MRX-20 requiresthe use of the TRF-UZ1 Z to enable communication, over the2.4GHz network, to compatible devices (TRC-780, THZ-100,etc.). Using this external antenna allows for optimal placementin the home or small office space.Compact design for easy installation Easily and discretely install the TRF-GE1 Extender. Maintainyour home decor while controlling your Total Control MRXAdvanced Network System Controller.Parts GuideThe TRF-UZ1 Z Extender includes:1 - TRF-UZ1 Z Extender 1 - Owner’s Manual
TRF-UZ1 Panel DescriptionsThe front, rear and bottom panel consists of: Power LED: When illuminated this light indicates the TRF-UZ1 is ON.Status LED: The Status LED signifies when the TRF-UZ1 is connectedto the network: Connected: Illuminates green. Not Connected: Remains OFF.Pairing: Illuminates orange.Data LED: The Data LED flashes as the TRF-UZ1 receives andtransmits data.DC 12V (1A): Plug in the included AC/DC adapter to power up theTRF-UZ1.LAN: Communicate over the network to an MRX-10/20 using anEthernet cable. Reset: Pressing the Reset button, with a stylus or paper clip, refreshesthe TRF-UZ1. Unplugging and re-plugging the power cable alsoresets the unit. Pressing and holding the Reset button for 10 seconds, factory defaultsthe TRF-UZ1 and places the unit back to its original factory condition.Page 2TRF-UZ1 Z EXTENDERPOWERLED STATUSLEDDATALEDDC 12VLANReset
TRF-UZ1 Z EXTENDERSpecificationsMicroprocessor: ARM32-bit Cortex- M3(120MHz)Power Supply: 12V DC 1ARAM: 128Mbyte Mobile DDRRF Range(radio frequency): 50 to 100 feet, depending upon the environmentRF Freqency: 2.405~2.480 GHzNAND: 128Mbyte FLASH: 768Kbytes SRAM: 128 + 4 KbyteWeight: 3.058 ozSize: 3.74” X 2.7” X 1.1”Power: 12V DC 1APage 3
TRF-UZ1 Z EXTENDERUSA Limited Warranty StatementYour Universal Remote Control, when delivered to you in new condition,is warranted against defects in materials or workmanship as follows:UNIVERSAL REMOTE CONTROL, INC. warrants this product againstdefects in material or workmanship for a period of one (1) year and as setforth below. Universal Remote Control will, at its sole option, repair theproduct using new or comparable rebuilt parts, or exchange the productfor a comparable new or rebuilt product. In the event of a defect, theseare your exclusive remedies.This Limited Warranty covers only the hardware components packagedwith the Product. It does not cover technical assistance for hardware orsoftware usage and it does not cover any software products whether ornot contained in the Product; any such software is provided "AS IS" unlessexpressly provided for in any enclosed software Limited Warranty. To obtain warranty service, you must deliver the product, freight prepaid,in its original packaging or packaging affording adequate protection toUniversal Remote Control at the address provided in the Owner's Manual.It is your responsibility to backup any macro programming, artwork,software or other materials that may have been programmed into yourunit. It is likely that such data, software, or other materials will be lostduring service and Universal Remote Control will not be responsible forany such damage or loss. A dated purchase receipt, Bill of Sale, InstallationContract or other verifiable Proof of Purchase is required. For productsupport and other important information visit Universal Remote Control'swebsite: http://www.UniversalRemote.com or call the Customer ServiceCenter (914) 835-4484. This Limited Warranty only covers product issues caused by defectsin material or workmanship during ordinary consumer use. It doesnot cover product issues caused by any other reason, including butnot limited to product issues due to commercial use, acts of God, third-party installation, misuse, limitations of technology, or modification ofor to any part of the Universal Remote Control product. This LimitedWarranty does not cover Universal Remote Control products sold asUSED, AS IS, REFURBISHED, so-called “B STOCK” or consumables(such as batteries). This Limited Warranty is invalid if the factory-appliedserial number has been altered or removed from the product. This LimitedWarranty is valid only in the United States of America. This LimitedWarranty specifically excludes products sold by unauthorized resellers.Page 4
LIMITATION OF REMEDIESUNIVERSAL REMOTE CONTROL SHALL NOT BE LIABLE FOR ANYINCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OFANY EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THISPRODUCT. IN NO EVENT SHALL UNIVERSAL REMOTE CONTROLBE LIABLE, WHETHER IN CONTRACT OR IN TORT (INCLUDINGNEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASEPRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE, OR FORANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIALDAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS,LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA,SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSSARISING OUT OF OR IN CONNECTION WITH THE ABILITY ORINABILITY TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARETO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BYLAW. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THEREIS NO OTHER WARRANTY EXPRESSED OR IMPLIED. UNIVERSALREMOTE CONTROL WILL NOT BE HELD RESPONSIBLE FORSTATEMENTS MADE BY OTHERS CONCERNING THEMERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSEON THIS PRODUCT. Some states or jurisdictions do not allow theexclusion or limitation of incidental or consequential damages, orallow limitations on how long an implied warranty lasts, so the abovelimitations or exclusions may not apply to you. This Limited Warrantygives you specific legal rights and you may have other rights whichvary from state to state or jurisdiction to jurisdiction.REV020708 TRF-UZ1 Z EXTENDERPage 5
Page 6TRF-UZ1 Z EXTENDERFederal Communication CommissionInterference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.Consult the dealer or an experienced radio/TV technician forhelp.Warning!Changes or modifications not expressly approved by the manufacturer couldvoid the user's authority to operate the equipment.Note : The manufacturer is not responsible for any Radio or TV interferencecaused by unauthorized modifications to this equipment. Such modificationscould void the user's authority to operate the equipment.FCC CautionThis device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference,and (2) this device must accept any interference received, including interferencethat may cause undesired operation.Any changes or modifications not expressly approved by the party responsiblefor compliance could void the authority to operate equipment.Federal Communication Commission (FCC) Radiation Exposure Statement The device and the antenna for this device must be installed to ensure a mini-mum separation distance of 20 cm more from a person's body. Other operatingconfigurations should be avoided.
Regulatory Information to the userCE conformity NoticeProducts with “CE” marking comply with the R&TTE Directive1995/5/EC, EMC Directive 2004/108/EC and Low VoltageDirective 2006/95/EEC issued by the commission of the EuropeanCommunity.1) R&TTE DirectiveSafety : EN 60950-1EMC : ETSI EN 301 489-1,17 RF : ETSI EN 300 3282) EMC DirectiveEmission : EN 55022Immunity : EN 55024Power : EN-61000-3-2, 33) Low Voltage DirectiveProduct safety : EN 60950-1Safety instruction for charging internal rechargeable battery ofremote controlUse only with EN60950-1 approved as Linited power source anddouble insulation() marked power adaptor & same ratings describedon the product label(12V DC 1A).Declaration of Conformity“Hereby, Universal Remote Control Inc. declares that this TRF-UZ1 isin compliance with the Essential requirements and other relevantprovisions of Directive 1999/5/EC.”Page 7TRF-UZ1 Z EXTENDERCertificationType No.(Model No.) TRF-UZ1Batch/Serial No. -Power Rating 12V DC 1AFrequency band 2.405~2.480 GHz
Page 8TRF-UZ1 Z EXTENDERDeclaration of ConformityCompany Name : Universal Remote Control Inc.Company Address : 500 Mamaroneck Avenue, Harrison, NY 10528, U.S.AContact Information : www.universalremote.comPhone: (914)835-4484 Fax: (914)835-4532Brand Name : UNIVERSAL remote controlProduct Name : BASE STATIONModel Name : TRF-UZ1 This product herewith complies with the requirements of EMC Directive (2004/108/EC) and R&TTE Directive(1995/5/EC) issued by the Commission of the European CommunityCompliance with these directives implies conformity to the following European Community EMC Directive EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 R&TTE Directive EN 60950-1 ETSI EN 301-489-1, 17 ETSI EN 300 328 Low Voltage Directive EN 60950-1List of test reports and/or certificate verified compliance with the standards above EMC Directive Report No. Testing Laboratory : Gumi College EMC Center R&TTE Directive Certificate No. Certificate Body : SIEMIC (No. 2200)Date of issue : March 16, 2012Name and signature of authorized person : James NovakSenior Product ManagerUniversal Remote Control Inc.
Page 9NOTE
Page 10NOTE
Page 11NOTE
Page 12NOTE
Page 13NOTE
Page 14NOTE
Page 15NOTE
Declaration of Conformity Code of Federal Regulations (CFR) 47, Part 2.906 Equipment Class : Computing device peripheral EUT Type : Base Station Rule Part(s) : FCC Part 15 subpart B Test Procedure(s) : ANSI C63.4 (2009) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operating. We hereby declare that this device bearing the trade name and model specified above has been shown to be in compliance with the applicable FCC rules under the most accurate measurement standards possible, and that all the necessary steps have been taken and are in force to assure that production units of the same equipment will continue to comply with the commission’s requirement Date of issue : Name and signature of authorized person : James NovakUniversal Remote Control Inc. MODEL NAME:TRF-UZ1TRADE NAME:UNIVERSAL Remote ControlRESPONSIBLE PARTY:Universal Remote Control Inc.ADDRESS:500Mamaroneck Avenue, Harrison, NY 10528, U.S.ACONTACT PERSON:James NovakTELEPHONE NUMBER:(914)835-4484
Duties of the Responsible Party The responsible party upon signing or accepting the Declaration of Conformity as specified in Section 2.906 of the FCC Rules hereby agrees to the duties listed below: § 2.1073(a). The responsible party warrants that each unit of equipment marketed under DoC is identical to the unit tested and found acceptable with the standards; and that the records maintained by the responsible party continue to reflect the equipment being produced are within the variation that can be expected due to quantity production and testing on a statistical basis. § 2.1073(b). The responsible party must have a written statement from the manufacturer or accredited test laboratory that the equipment complies with the appropriate technical standards. § 2.1073(c). In case of transfer of control of equipment, as in the case of sale or merger, the new responsible party shall bear the responsibility of continued compliance of the equipment. § 2.1073(d). Equipment shall be retested if any modifications or changes are made that could adversely affect the emanation characteristics of the equipment. § 2.1073(e). If ay modifications or changes made by anyone other than the responsible party, the party making the modifications or changes, if located within the U.S., becomes the new responsible party. The new responsible party must comply with all provisions for the DoC, including having test data on files demonstrating that the product continues to comply with all of the applicable technical standards. § 2.1075(a)(1). The responsible party shall maintain records of the original design drawings and specifications and all changes made to the product that may affect compliance. § 2.1075(a)(2). The responsible party shall maintain records of the procedures used for production inspection and testing to insure the conformance with the FCC Rules. § 2.946(a)(1). The test report data shall be provided to the FCC within 14 days of delivery of request. The test sample(s) shall be provided within 60 days of delivery of request. § 2.946(b). In cases involving harmful interference of safety of life or property, the production sample must be provided within 60 days, but not less than 14 days. Failure to comply with such a request with the time frame shown may be cause for forfeiture, pursuant to Section 1,80 of Part 1 of the FCC Rules.
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.comOCE-0132B Rev 01

Navigation menu